TLE8250GVIOXUMA5 - High-Speed CAN Transceiver 1MBd | Infineon
부품 번호: TLE8250GVIOXUMA5 ✓ 활성TLE8250GVIOXUMA5 개요
A CAN (Controller Area Network) transceiver is the physical-layer interface between a CAN protocol controller (usually integrated in a microcontroller) and the twisted-pair bus wires. Within the automotive and industrial networking hierarchy, it sits at the bottom of the stack: CAN network -> high-speed CAN physical layer (ISO 11898-2) -> CAN transceiver -> CAN controller. The transceiver converts the controller's TXD logic stream into differential bus signaling on CANH and CANL, and recovers the differential bus signal to a logic-level RXD output, while protecting the microcontroller against disturbances coming from the network.
Key features include full ISO 11898-2 compliance, up to 1 MBd signaling for classical CAN frames, low electromagnetic emission (EME) and high immunity against external electromagnetic interference (EMI), and robust ESD protection on the bus pins. The separate VIO pin lets the TXD and RXD logic levels adapt to 3.3V or 5V microcontroller ports, eliminating level-shifting glue logic in mixed-voltage systems.
The device integrates a highly symmetric driver stage that minimizes bus-line unbalance, improving common-mode noise behavior. Receiver hysteresis of 200 mV suppresses false switching from bus reflections and noise, and integrated protection functions guard against transient events typical of automotive 12V environments.
Typical applications include automotive body and powertrain ECUs, industrial CANopen and DeviceNet nodes, gateways connecting CAN to other networks, and motor-drive communication modules where a 3.3V MCU must talk over a 5V CAN physical layer.
Design tip: keep the VIO pin within its specified range and decouple VCC and VIO separately; the transceiver is half-duplex, so ensure the protocol controller performs proper arbitration and never drives TXD against an active reception.
This page synthesizes drop-in alternatives, cross-reference data, applications, and engineering design notes in one place, beyond what a standard distributor listing provides.
드롭인 대체품: TLE8250GVIOXUMA5 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: TLE8250GVIOXUMA5 (동일 폼 팩터 및 풋프린트) — 차이점: Package, RoHS Status, Data Rate, Product Type, Automotive Qualification.
TLE8250GXUMA5
✅ 드롭인가격 문의
데이터시트 보기 →TJA1051T/1J
✅ 드롭인가격 문의
데이터시트 보기 →TJA1057GTJ
✅ 드롭인가격 문의
데이터시트 보기 →TLE6250GV33XUMA1
✅ 드롭인가격 문의
데이터시트 보기 →TLE8250GVIOXUMA5 사양
| Protocol | CANbus |
| 데이터 속도 | 1 MBd |
| Number of Drivers/Receivers | 1/1 |
| Duplex | Half |
| 공급 전압 | 4.5 V to 5.5 V |
| Receiver Hysteresis | 200 mV |
| 동작 온도 | -40C to +150C |
| 실장 유형 | Surface Mount |
| Supplier Device Package | PG-DSO-8-16 |
| 패키지 / 케이스 | 8-SOIC (0.154in, 3.90mm Width) |
| Physical Layer Standard | ISO 11898-2 (high-speed CAN) |
| I/O Voltage Input (VIO) | Yes, separate logic-level supply |
| ESD Protection | Robust ESD protection on bus pins |
| EME/EMI | Low electromagnetic emission, high EMI immunity |
| ECCN | EAR99 |
| HTSUS | 8542.39.0001 |
| Moisture Sensitivity Level | 2A |
| Part Status | Active |
TLE8250GVIOXUMA5 핀 구성
| 핀 1 | TXD — Transmit data input from CAN controller (logic level set by VIO) |
| 핀 2 | GND — Ground |
| 핀 3 | VCC — Transceiver supply, 4.5V to 5.5V |
| 핀 4 | RXD — Receive data output to CAN controller (logic level set by VIO) |
| 핀 5 | VIO — I/O voltage input setting TXD/RXD logic levels |
| 핀 6 | CANL — Low-level CAN bus line |
| 핀 7 | CANH — High-level CAN bus line |
| 핀 8 | NC — Not connected (per datasheet) |
일반적인 애플리케이션
TLE8250GVIOXUMA5 적합 용도: 6 애플리케이션s: Automotive Body Electronics ECUs, Industrial CANopen and DeviceNet Nodes, CAN Gateways and Network Bridges, Motor Drive and Inverter Communication, Agricultural and Off-Highway Vehicles, Diagnostic Interfaces and Test Tools.
Automotive Body Electronics ECUs
Body control modules, door modules, lighting controllers, and seat ECUs all communicate over 500 kbps high-speed CAN, exactly the regime the TLE8250GVIOXUMA5 targets. Its ISO 11898-2 compliance guarantees interoperability with the rest of the vehicle bus, while low electromagnetic emission helps the module pass automotive EMC test plans without extra suppression components. The VIO pin lets a cost-optimized 3.3V body microcontroller connect directly, removing level-shifter ICs from the BOM. The -40C to +150C operating range covers passenger-compartment and near-engine mounting locations, and the robust ESD protection on CANH/CANL withstands the transient events typical of 12V vehicle harnesses.
추천
Industrial CANopen and DeviceNet Nodes
Industrial fieldbus nodes - drives, IO blocks, sensors, and gateways - rely on high-speed CAN physical layers standardized by CANopen and DeviceNet. The TLE8250GVIOXUMA5 supplies the 1 MBd-capable differential interface these profiles require, with 200 mV receiver hysteresis that stabilizes reception on long, cable-infested factory networks prone to reflections and common-mode noise. Its low-EMI driver helps panels meet industrial EMC requirements, and the separate VIO input matches both legacy 5V PLC logic and modern 3.3V MCUs on the same PCB layout. High immunity to external electromagnetic interference keeps communication intact near variable-frequency drives and contactor switching events common in industrial cabinets.
추천
CAN Gateways and Network Bridges
Gateways bridging powertrain CAN, body CAN, and diagnostic lines need transceivers that behave identically on every channel, and the TLE8250GVIOXUMA5 provides that uniform ISO 11898-2 physical layer at up to 1 MBd per channel. The VIO input is particularly useful in gateway designs that pair a 3.3V application MCU with mixed 5V signaling, avoiding level translators that add delay to the critical RXD path. Its low EME is important because gateways often sit near sensitive RF or analog sections, and the robust bus-pin ESD protection handles cable-attached diagnostic interfaces. Per Infineon, the transceiver also shields the microcontroller against disturbances coming from the network.
추천
Motor Drive and Inverter Communication
Servo drives, inverters, and motion controllers use CAN for setpoint and status traffic in noisy power-electronic environments. The TLE8250GVIOXUMA5's high immunity against external electromagnetic interference is the deciding parameter here: switching nodes of tens of volts per nanosecond couple large transients into the bus wiring, and the receiver's 200 mV hysteresis plus the transceiver's common-mode rejection keep bit error rates low. The 4.5V to 5.5V VCC rail is typically already present in drive control boards, and the VIO pin accepts the 3.3V outputs of modern DSP/MCU control sections directly. The PG-DSO-8 footprint also supports isolation-compatible layouts where a digital isolator sits between controller and transceiver.
추천
Agricultural and Off-Highway Vehicles
Tractors, harvesters, construction machines, and marine equipment standardize on CAN (including J1939 at 250 kbps and ISOBUS implementations), all of which run comfortably within the TLE8250GVIOXUMA5's 1 MBd capability. These platforms expose the transceiver to harsher conditions than passenger cars: long harnesses, 24V system transients, moisture, and wide temperature swings. The part's -40C to +150C rating and robust ESD protection on the bus pins address those stressors, while ISO 11898-2 compliance guarantees node interoperability across mixed-vendor fleets. The VIO feature supports the 3.3V display and telematics controllers increasingly integrated into off-highway cabs alongside legacy 5V logic.
추천
Diagnostic Interfaces and Test Tools
Handheld CAN analyzers, OBD adapters, and production EOL programmers benefit from the TLE8250GVIOXUMA5's combination of full 1 MBd support - needed for fast flash reprogramming over CAN - and the VIO input, which lets one hardware design talk to both 3.3V and 5V targets without modification. Robust bus-pin ESD handling matters because diagnostic cables are plugged into arbitrary vehicles and modules all day, accumulating electrostatic stress. The compact PG-DSO-8 package fits the small probe-form-factor PCBs typical of these tools, and low EME avoids corrupting nearby RF measurements when the tool is used in lab or EMC-chamber settings.
추천
추천 제품 요약
엔지니어링 참조 데이터: TLE8250GVIOXUMA5 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | TLE8250GXUMA5 | TJA1051T/1J | TJA1057GTJ | TLE6250GV33 |
|---|---|---|---|---|---|
| Package | PG-DSO-8-16 (8-SOIC) | PG-DSO-8-16 (8-SOIC) - same | 8-SOIC (3.90mm) - same footprint | 8-SOIC - same footprint | PG-DSO-8 - same footprint |
| Brand | Infineon Technologies | Infineon Technologies | NXP Semiconductors | NXP Semiconductors | Infineon Technologies |
| Data Rate | 1 MBd | 1 MBd | 1 Mbps | 1 Mbps | 1 MBd |
| Physical Layer Standard | ISO 11898-2 | ISO 11898-2 | ISO 11898-2 | ISO 11898-2 | ISO 11898-2 |
| Duplex / Drivers-Receivers | Half, 1/1 | Half, 1/1 | Half, 1/1 | Half, 1/1 | Half, 1/1 |
주요 차별점
- Separate VIO logic-level supply input (vs TJA1051T/1J)
- 150C maximum operating temperature with VIO feature (vs TLE6250GV33)
- Same-footprint no-VIO second source within the family (vs TLE8250GXUMA5)
설계 노트
Place the TLE8250GVIOXUMA5 close to the CAN connector to minimize the stub length of CANH/CANL traces; stubs act as transmission-line discontinuities at 1 Mbps and can cause reflections that the 200 mV receiver hysteresis cannot fully mask. Route CANH and CANL as a tightly coupled differential pair with matched lengths and a characteristic impedance near 120 ohms including the connector. Decouple VCC with 100 nF ceramic plus bulk capacitance, and decouple VIO separately with 100 nF since it only sources logic-level gate charge. Keep the split termination (2 x 60 ohm with common-mode stabilization capacitor) at the network ends, not at each node.
Do not tie VIO to a rail that powers up after VCC or floats during microcontroller reset - undefined logic levels on TXD can drive random dominant states onto the bus and disturb other nodes. Tie VIO directly to the MCU IO supply and ensure it is valid whenever VCC is present. Also remember the transceiver is half-duplex: the CAN controller performs arbitration, so never bit-bang TXD manually. When second-sourcing to the TLE8250GXUMA5 (no VIO) or an NXP SOIC-8 part, re-verify the pin-5 function against that part's pin-description table before qualifying the layout change.
Infineon specifies low electromagnetic emission (EME) for the TLE8250G family, but realized EMC still depends on layout: keep the loop area between VCC, GND, and the bus pins small, and place the common-mode choke (if used in the network design) directly at the connector side of the transceiver bus pins. Symmetry of CANH/CANL routing is the dominant factor in common-mode emission; a few millimeters of asymmetry can degrade emissions at CAN bit-rate harmonics. Use the manufacturer's typical application circuit in the TLE8250G datasheet as the reference topology when drawing the schematic.
규정 준수 정보
ECCN EAR99 and HTSUS 8542.39.0001 are listed in distributor data. RoHS/REACH status should be confirmed on the Infineon product page before release.