TLV2371ID - 3MHz RRIO Op Amp | Texas Instruments
MPN: TLV2371ID ✓ সক্রিয়TLV2371ID সারাংশ
A rail-to-rail operational amplifier is an analog amplifier whose input common-mode range and output voltage swing extend close to the positive and negative supply rails. This capability helps designers use nearly the full voltage range of a low-voltage supply while preserving usable signal range. In the broader component hierarchy, the TLV2371 belongs to the operational-amplifier family, combines with analog signal-chain ICs, and ultimately supports the wider category of analog and mixed-signal semiconductors.
The headline operating characteristics include a 3 MHz gain-bandwidth product, 2.1 V/us slew rate, and 550 µA quiescent current. Its rail-to-rail input and output behavior supports low-voltage designs in which the signal may approach either supply rail. The 2.7 V minimum operating supply is suitable for modern 3.3 V systems, while the 16 V maximum recommended supply provides additional flexibility for industrial and instrumentation applications operating from higher rails.
The single-amplifier architecture makes the TLV2371ID appropriate for independent gain, filtering, buffering, and level-shifting stages. A reported input bias current of 1 pA is particularly useful when high-impedance sources must not be heavily loaded. The 4.5 mV offset figure identified for the device helps engineers characterize small-signal accuracy, while the 2.1 V/us slew rate influences how quickly the output can follow large-signal transitions.
Typical uses include low-power sensor conditioning, battery-powered monitoring, current measurement, signal buffering, and general-purpose analog gain stages. The shutdown control can also reduce power consumption in intermittently sampled systems. In designs operating near the supply rails, engineers should account for input and output range limits, output loading, and the transition behavior associated with the rail-to-rail architecture.
When laying out an 8-pin SOIC implementation, place the decoupling capacitor close to the supply pins and connect the shutdown control to a defined logic level. Avoid leaving the shutdown pin floating, and check its required polarity in the manufacturer datasheet before finalizing control logic. Stable feedback-network layout and guarding of high-impedance inputs remain important for preserving accuracy.
This page combines the manufacturer electrical characteristics, ordering information, drop-in alternatives, and practical design guidance to support component selection and PCB implementation. It also highlights where shutdown polarity, supply limits, and input behavior must be checked during schematic review.
এর জন্য ড্রপ-ইন বিকল্প TLV2371ID — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible TLV2371ID (একই form factor এবং footprint).
TLV2371IDG4
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
TLV2371IDR
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
TLV2371ID সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | Single operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 3 MHz |
| Slew Rate | 2.1 V/us |
| Minimum Operating Supply Voltage | 2.7 V |
| Maximum Recommended Supply Voltage | 16 V |
| কুইসেন্ট কারেন্ট | 550 µA per channel |
| Input Offset Voltage | 4.5 mV |
| Input Bias Current | 1 pA |
| Input Common-Mode Range | Rail-to-rail |
| Output Voltage Swing | Rail-to-rail |
| Shutdown Control | Yes |
| অপারেটিং তাপমাত্রার পরিসর | Extended industrial temperature range |
| প্যাকেজ | 8-pin SOIC |
| মাউন্টিং টাইপ | Surface mount |
| RoHS স্ট্যাটাস | Compliant |
TLV2371ID পিন কনফিগারেশন
| পিন 1 | OUT — Operational-amplifier output |
| পিন 2 | V- — Negative supply or ground connection |
| পিন 3 | +IN — Noninverting input |
| পিন 4 | -IN — Inverting input |
| পিন 5 | NC — Not connected |
| পিন 6 | SHDN — Shutdown control input |
| পিন 7 | + — Positive supply |
| পিন 8 | V+ — Positive supply connection |
সাধারণ ব্যবহার
TLV2371ID এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Low-Power Sensor Signal Conditioning, Battery-Powered Monitoring Circuit, Current-Shunt Amplifier, Precision Analog Signal Buffer, Active Low-Pass Filter, Industrial Control and Instrumentation.
Low-Power Sensor Signal Conditioning
The TLV2371ID fits low-power sensor-conditioning stages that require useful signal swing from a 2.7 V minimum supply. Its rail-to-rail input range allows the amplifier to process signals near the supply rails, while the reported 1 pA input bias current minimizes disturbance of high-impedance sensors. The 3 MHz gain-bandwidth product supports moderate-bandwidth instrumentation, and the 550 µA quiescent current limits idle demand. In a typical implementation, the device amplifies a sensor output and drives a sampled ADC or comparator input. Designers should still select suitable feedback resistors and check the output range against the connected load.
Battery-Powered Monitoring Circuit
The TLV2371ID is appropriate for battery-powered monitoring circuits where every milliamp can shorten operating time. It operates from 2.7 V to 16 V and consumes 550 µA quiescent current, providing a useful low-power foundation for portable sensing and threshold-detection blocks. Rail-to-rail input and output behavior increases usable signal range in compact 3.3 V systems. The shutdown function can further reduce consumption when measurements occur intermittently. A practical design should define the shutdown logic level, confirm the required measurement bandwidth, and verify that output loading does not materially increase supply current.
Current-Shunt Amplifier
The TLV2371ID can serve as the gain stage in a low-side current-shunt measurement circuit. Its 1 pA input bias current is favorable for the high-impedance side of a shunt network, while rail-to-rail input operation helps accommodate small differential signals near a 2.7 V supply. The 3 MHz bandwidth and 2.1 V/us slew rate are suitable for many monitoring and control loops, subject to the selected shunt resistance and amplifier gain. Engineers should apply the correct differential sign, use Kelvin routing for precision measurements, and verify output-headroom limits across the intended current range.
Precision Analog Signal Buffer
The TLV2371ID can buffer a high-impedance analog source into a downstream ADC, filter, or comparator. Rail-to-rail input operation helps maintain signal fidelity when the source swings close to the 2.7 V lower supply limit, and the single-channel 8-pin SOIC keeps the circuit compact. The 3 MHz gain-bandwidth product provides useful bandwidth for moderate-frequency signals, while the 2.1 V/us slew rate helps the output follow step changes. Because the listed input offset voltage is 4.5 mV, applications requiring sub-millivolt absolute accuracy should include offset and drift in the error budget and consider a more precise amplifier.
Active Low-Pass Filter
The TLV2371ID is suitable for building an active low-pass filter in low-voltage instrumentation. Its 3 MHz gain-bandwidth product leaves useful closed-loop bandwidth for common first- and second-order filter stages, and the 550 µA quiescent current supports power-constrained designs. Rail-to-rail input and output characteristics are especially helpful when filtering signals that occupy much of a 2.7 V to 5 V supply range. Component tolerances and the op-amp's frequency response determine the achieved cutoff and Q. Place feedback components close to the device, provide local supply decoupling, and verify filter stability across temperature and process variation.
Industrial Control and Instrumentation
The TLV2371ID supports industrial control and instrumentation blocks that need a compact, general-purpose amplifier with extended industrial-temperature operation. The 16 V maximum recommended supply provides flexibility for 12 V and lower-voltage control systems, while the 2.7 V minimum supports modern embedded rails. Its 3 MHz bandwidth and 2.1 V/us slew rate are adequate for many sensor, interface, and signal-conditioning functions. For factory equipment, engineers should account for surge, grounding, noise, and component tolerances at the board level, and they should verify the exact temperature grade and lifecycle status before production release.
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা TLV2371ID — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | TLV2371IDG4 | TLV2371IDR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Number of Channels | 1 channel | 1 channel | 1 channel |
| Gain-Bandwidth Product | 3 MHz | 3 MHz | 3 MHz |
| Slew Rate | 2.1 V/us | 2.1 V/us | 2.1 V/us |
| Operating Supply Range | 2.7 V to 16 V | 2.7 V to 16 V | 2.7 V to 16 V |
| Quiescent Current | 550 µA per channel | 550 µA per channel | 550 µA per channel |
| Input Offset Voltage | 4.5 mV | 4.5 mV | 4.5 mV |
| Input Bias Current | 1 pA | 1 pA | 1 pA |
| Shutdown Control | Yes | Yes | Yes |
মূল পার্থক্যসমূহ
- Combines rail-to-rail operation with low quiescent current (বনামTLV2371IDG4)
- Operates across a broad single-supply range (বনামTLV2371IDR)
- Single-channel 8-pin SOIC implementation (বনামTLV2371IDG4)
ডিজাইন নোট
Place a local bypass capacitor directly between the positive supply and ground pins, with the ground connection following the shortest practical return path. The TLV2371ID operates from 2.7 V to 16 V, but the bypass network should be sized for the supply impedance and expected switching noise rather than only for the 550 µA quiescent current. If the shutdown pin is not used, connect it to the inactive level shown in the manufacturer datasheet instead of allowing it to float.
Keep the feedback resistors, input source, and noninverting input connection close to the 8-pin SOIC to minimize parasitic capacitance and susceptibility to injected noise. For high-impedance sources, minimize copper area around pins 3 and 4, clean the board surface after soldering, and avoid running sensitive traces parallel to switching-current paths. A solid ground plane beneath the amplifier can reduce ground inductance, but it should not replace a deliberate return-current path to the supply capacitor.
Do not assume that rail-to-rail input and output operation eliminates all range restrictions near the supply rails. Review the common-mode and output-swing graphs in the Texas Instruments TLV2371 datasheet for the actual supply voltage, output load, and temperature. Also verify shutdown polarity before connecting system-control logic. A shutdown command with the wrong polarity can disable the amplifier or interfere with intended power management.
Use the 3 MHz gain-bandwidth product and 2.1 V/us slew rate to define the usable signal bandwidth rather than assuming the amplifier has uniform performance to 3 MHz. For filters or pulse-processing circuits, calculate the closed-loop response at each gain setting and compare it with the required waveform bandwidth. The listed 4.5 mV input offset voltage should also be included when small DC signals are measured at high gain.
কমপ্লায়েন্স তথ্য
The component listing identifies the TLV2371ID as RoHS compliant. No explicit exact-part qualification was found for REACH, AEC-Q100, lead-free status, halogen-free status, or conflict-minerals compliance.