TLV2762CD - 3.6V 500kHz Dual RRIO Op Amp | Texas Instruments
MPN: TLV2762CD ✓ সক্রিয়TLV2762CD সারাংশ
An operational amplifier is an active analog circuit that amplifies the voltage difference between two inputs while using negative feedback to control gain and bandwidth. A rail-to-rail input stage accepts signals close to the supply rails, while a rail-to-rail output stage can produce output voltages near either rail. This capability improves dynamic range in systems whose signal range approaches the available supply voltage. The TLV2762 belongs to the operational-amplifier hierarchy, specifically the low-voltage, low-power, rail-to-rail amplifier class.
The two independent amplifier channels can perform filtering, buffering, level shifting, transimpedance conversion, and differential sensing. Key characteristics include 500 kHz bandwidth, 230 V/ms slew rate, 550 µV typical offset voltage, 6 µV/°C typical offset drift, 15 pA typical input-bias current, and 20 µA typical amplifier supply current. Rail-to-rail input and output operation allow signals to use nearly the complete 1.8 V to 3.6 V supply range.
The 500 kHz bandwidth gives useful closed-loop performance for moderate-frequency signals while keeping quiescent current low at 20 µA per amplifier. This bandwidth-to-power balance is appropriate for portable sensor nodes, where a higher-speed amplifier may add unnecessary supply demand. The 230 V/ms slew rate preserves large-signal response, while the 95 nV/√Hz noise density supports low-noise measurement of slow analog signals.
Typical uses include battery-powered sensor conditioning, portable medical monitoring, industrial current measurement, low-voltage data acquisition, and general-purpose analog filtering. In each case, the device can operate directly from a 1.8 V rail and provide input or output headroom that is difficult to obtain with a conventional non-rail-to-rail amplifier.
Designers should verify input and output common-mode limits, output swing, capacitive-load stability, and noise performance under the intended supply and load conditions. Place bypass capacitors close to the supply pins, keep feedback routing compact, and avoid excessive loading on the output. Although the SOIC-8 outline supports conventional board assembly, the low package thermal limit still requires consideration of power dissipation during sustained high-output-current operation.
This page organizes the TLV2762CD electrical characteristics, package information, verified drop-in candidates, application guidance, and design considerations into a compact engineering reference for low-voltage analog design.
এর জন্য ড্রপ-ইন বিকল্প TLV2762CD — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible TLV2762CD (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Slew Rate, Amplifier Type, Maximum Supply Voltage, Gain-Bandwidth Product.
TLV2762ID
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →TLV2772CD
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →TLV2772ID
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়মূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →TLV2762CD সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 1.8 V to 3.6 V |
| Unity-Gain Bandwidth | 500 kHz |
| Slew Rate | 230 V/ms |
| Input Offset Voltage | 550 µV typical |
| Input Offset Voltage Drift | 6 µV/°C typical |
| Input Bias Current | 15 pA typical |
| Input Voltage Noise Density | 95 nV/√Hz at 1 kHz |
| সাপ্লাই কারেন্ট | 20 µA typical |
| Shutdown Supply Current | 3 pA typical |
| Input Common-Mode Range | Rail-to-rail |
| Output Common-Mode Range | Rail-to-rail |
| অপারেটিং তাপমাত্রার পরিসর | 0 °C to +70 °C |
| প্যাকেজ | 8-pin SOIC |
| মাউন্টিং টাইপ | Surface mount |
| RoHS স্ট্যাটাস | Compliant |
TLV2762CD পিন কনফিগারেশন
| পিন 1 | OUTA — Channel A output |
| পিন 2 | IN-A — Channel A inverting input |
| পিন 3 | IN+A — Channel A non-inverting input |
| পিন 4 | V- — Negative supply connection |
| পিন 5 | IN+B — Channel B non-inverting input |
| পিন 6 | IN-B — Channel B inverting input |
| পিন 7 | OUTB — Channel B output |
| পিন 8 | V+ — Positive supply connection |
সাধারণ ব্যবহার
TLV2762CD এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Low-Voltage Control, Portable Data Acquisition, Low-Voltage Current Measurement, Active Filtering and Level Shifting.
Battery-Powered Sensor Conditioning
The TLV2762CD fits low-voltage sensor front ends because it operates from 1.8 V to 3.6 V, consumes 20 µA typical supply current per amplifier, and accepts or produces signals near either supply rail. Place the dual channels around a resistive sensor bridge to buffer the excitation outputs and amplify the differential measurement at the input stage. Rail-to-rail operation preserves much of the signal range in compact battery-powered products. The 500 kHz bandwidth supports moderate-bandwidth filtering, while the 95 nV/√Hz input-noise density helps preserve weak sensor signals. Check source-impedance-induced error and the final amplifier saturation limits before fixing the gain.
সুপারিশকৃত
Portable Medical Monitoring
The TLV2762CD is appropriate for portable monitoring modules that require low-noise amplification from a 1.8 V or 3.3 V rail. Its 95 nV/√Hz input-voltage noise density and 15 pA typical input-bias current are useful when processing low-amplitude physiological or biochemical signals, while the two channels can provide gain and active filtering. The 500 kHz bandwidth allows response beyond the bandwidth of many slow sensor signals without requiring a high-current amplifier. Rail-to-rail input and output behavior improves usable signal span in compact wearables. Validate noise, settling time, patient-safety isolation, and the complete analog front end for the intended measurement class.
সুপারিশকৃত
Industrial Low-Voltage Control
The TLV2762CD can condition low-level control signals in 3.3 V industrial systems where rail-to-rail operation and low supply current are useful. Its dual channels can amplify a sensor output and provide an active filter or level-shifting stage for a controller input. The 1.8 V to 3.6 V operating range supports both 1.8 V and 3.3 V rails, and 500 kHz bandwidth handles many process-control signals with modest speed requirements. For industrial use, review the commercial 0 °C to +70 °C limit and select an industrial-temperature grade when the enclosure temperature can exceed that range. Also confirm the grounding and isolation arrangement for the deployed equipment.
সুপারিশকৃত
Portable Data Acquisition
The TLV2762CD suits compact, low-voltage data-acquisition systems requiring two analog channels, rail-to-rail signal handling, and modest bandwidth. Its 500 kHz unity-gain bandwidth supports conditioning of temperature, pressure, position, and slow vibration sensors without the higher supply demand of a 10 MHz amplifier. The 20 µA typical supply current helps preserve battery life, while 95 nV/√Hz noise density supports low-amplitude measurements. Use one channel for gain and one for filtering or active offset correction when appropriate. Choose external precision resistors and an anti-alias filter based on the sensor bandwidth, because the amplifier itself does not determine the final acquisition accuracy.
সুপারিশকৃত
Low-Voltage Current Measurement
The TLV2762CD can amplify the output of a low-side current shunt in a 3.3 V supply design. Its rail-to-rail input stage accepts shunt voltages near the lower or upper rail, and the dual-channel configuration can provide differential gain followed by filtering or a second signal path. With 95 nV/√Hz input-voltage noise density, it is suitable for many precision current measurements where the shunt impedance and amplifier gain determine the useful resolution. The 500 kHz bandwidth supports faster transient capture than a static precision amplifier. Keep shunt and feedback traces short, use a Kelvin connection where possible, and verify input common-mode behavior under maximum current before production release.
সুপারিশকৃত
Active Filtering and Level Shifting
The TLV2762CD is useful for implementing active filters and level-shifting stages in portable analog systems. Its rail-to-rail output allows the conditioned signal to approach the positive or negative supply more closely than a conventional amplifier, improving utilization of a 1.8 V or 3.3 V rail. The 500 kHz bandwidth supports moderate-frequency filter sections, and the 230 V/ms slew rate reduces large-signal distortion. The two channels allow cascading filter stages when the calculated Q and stability requirements permit it. Use resistor and capacitor values that remain appropriate for the intended gain, check the closed-loop response across temperature, and place feedback components close to the device to minimize parasitic feedback.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা TLV2762CD — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | TLV2762ID | TLV2772CD | TLV2772ID |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint |
| Amplifier Configuration | Dual | Dual | Dual | Dual |
| Operating Temperature | 0 °C to +70 °C | -40 °C to +85 °C | 0 °C to +70 °C | -40 °C to +85 °C |
| Input and Output Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
মূল পার্থক্যসমূহ
- Commercial-temperature drop-in simplicity (বনামTLV2762ID)
- Low supply current with usable bandwidth (বনামTLV2772CD)
- High-impedance signal conditioning (বনামTLV2772ID)
ডিজাইন নোট
Place the supply bypass capacitor immediately between the V+ and V- pins. Keep the supply trace short, connect the capacitor ground directly to the device ground, and use a separate return path for input and feedback currents. Because the device can operate down to 1.8 V, verify that every upstream rail remains within the operating range during startup, shutdown, and load transients.
Keep the two inverting-input feedback components close to pins 2 and 6 to minimize parasitic capacitance and unwanted feedback. Route the non-inverting inputs away from supply, clock, and high-current switching nodes. For sensitive measurements, use a ground plane that remains continuous beneath the amplifier and separate analog input routing from digital return currents.
Check output stability with the actual load, including cable capacitance, probe capacitance, and the input capacitance of the following stage. If ringing appears, reduce the capacitive load or add a small isolation resistor at the output. Recalculate the gain and bandwidth after adding compensation so that the final closed-loop response still meets the signal-chain requirements.
Rail-to-rail input does not eliminate input-bias-current error when driving a high source impedance, and rail-to-rail output does not eliminate the need to observe output swing limits. Use the manufacturer characteristic curves to confirm input common-mode range and output voltage under the actual load. Also confirm the ambient temperature against the 0 °C to +70 °C rating before using TLV2762CD in an industrial enclosure.
কমপ্লায়েন্স তথ্য
The product listing identifies the TLV2762CD as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or automotive qualification statement was identified.