Texas Instruments

TLV2762CD - 3.6V 500kHz Dual RRIO Op Amp | Texas Instruments

MPN: TLV2762CD ✓ 啟用中
1.8 V to 3.6 V Vdss 15 pA typical Id 8-pin SOIC Package
MOQ: 1 |

TLV2762CD 概覽

Texas Instruments TLV2762CD is a dual, micropower, rail-to-rail input/output operational amplifier designed for low-voltage signal conditioning. It operates from a single 1.8 V to 3.6 V supply, provides 500 kHz unity-gain bandwidth, and is packaged in an 8-pin SOIC. Each channel combines rail-to-rail inputs and outputs with 95 nV/√Hz input-voltage noise, making it suitable for battery-powered instrumentation, sensor interfaces, and precision analog signal paths.

An operational amplifier is an active analog circuit that amplifies the voltage difference between two inputs while using negative feedback to control gain and bandwidth. A rail-to-rail input stage accepts signals close to the supply rails, while a rail-to-rail output stage can produce output voltages near either rail. This capability improves dynamic range in systems whose signal range approaches the available supply voltage. The TLV2762 belongs to the operational-amplifier hierarchy, specifically the low-voltage, low-power, rail-to-rail amplifier class.

The two independent amplifier channels can perform filtering, buffering, level shifting, transimpedance conversion, and differential sensing. Key characteristics include 500 kHz bandwidth, 230 V/ms slew rate, 550 µV typical offset voltage, 6 µV/°C typical offset drift, 15 pA typical input-bias current, and 20 µA typical amplifier supply current. Rail-to-rail input and output operation allow signals to use nearly the complete 1.8 V to 3.6 V supply range.

The 500 kHz bandwidth gives useful closed-loop performance for moderate-frequency signals while keeping quiescent current low at 20 µA per amplifier. This bandwidth-to-power balance is appropriate for portable sensor nodes, where a higher-speed amplifier may add unnecessary supply demand. The 230 V/ms slew rate preserves large-signal response, while the 95 nV/√Hz noise density supports low-noise measurement of slow analog signals.

Typical uses include battery-powered sensor conditioning, portable medical monitoring, industrial current measurement, low-voltage data acquisition, and general-purpose analog filtering. In each case, the device can operate directly from a 1.8 V rail and provide input or output headroom that is difficult to obtain with a conventional non-rail-to-rail amplifier.

Designers should verify input and output common-mode limits, output swing, capacitive-load stability, and noise performance under the intended supply and load conditions. Place bypass capacitors close to the supply pins, keep feedback routing compact, and avoid excessive loading on the output. Although the SOIC-8 outline supports conventional board assembly, the low package thermal limit still requires consideration of power dissipation during sustained high-output-current operation.

This page organizes the TLV2762CD electrical characteristics, package information, verified drop-in candidates, application guidance, and design considerations into a compact engineering reference for low-voltage analog design.

直接替換替代品,適用於 TLV2762CD — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: TLV2762CD (相同外形與佔位) — 差異在於 Package, Slew Rate, Amplifier Type, Maximum Supply Voltage, Gain-Bandwidth Product.

Texas Instruments
Package: 8-pin SOIC, 0.154 inch (3.90 mm) wide
Maximum Supply Voltage: 3.6 V
Gain-Bandwidth Product: 500 kHz
比較對象 TLV2762CD →
Texas Instruments
Package: SOIC-8 (D)
Slew Rate: 10.5 V/µs
Maximum Supply Voltage: 5.5 V
比較對象 TLV2762CD →
Texas Instruments
Slew Rate: 10.5 V/us
Amplifier Type: Dual CMOS operational amplifier
Maximum Supply Voltage: 5.5 V
比較對象 TLV2762CD →

TLV2762ID

✅ 直接替換 ⚠️ 規格未經驗證
Texas Instruments
📦 8-pin SOIC
Dual general-purpose operational amplifier · 2 circuits · 1.8 V · 3.6 V · 500 kHz · Approximately 20 microampere per amplifier · Rail-to-rail · Rail-to-rail

聯絡詢價

查看資料表 →

TLV2772CD

✅ 直接替換 ⚠️ 規格未經驗證
Texas Instruments
📦 8-pin SOIC
2 channels · 5.5 V · 2.7 V · 5.1 MHz · 10.5 V/µs · 1 mA · Rail-to-rail output · CMOS

聯絡詢價

查看資料表 →

TLV2772ID

✅ 直接替換 ⚠️ 規格未經驗證
Texas Instruments
📦 8-pin SOIC
Dual CMOS operational amplifier · 2 channels · 5.5 V · 2.7 V · 5.1 MHz · 10.5 V/us · Rail-to-rail output

聯絡詢價

查看資料表 →

TLV2762CD 最大額定值與電氣特性

Amplifier Type Dual general-purpose operational amplifier
Number of Channels 2 channels
Supply Voltage Range 1.8 V to 3.6 V
Unity-Gain Bandwidth 500 kHz
Slew Rate 230 V/ms
Input Offset Voltage 550 µV typical
Input Offset Voltage Drift 6 µV/°C typical
Input Bias Current 15 pA typical
Input Voltage Noise Density 95 nV/√Hz at 1 kHz
供應電流 20 µA typical
Shutdown Supply Current 3 pA typical
Input Common-Mode Range Rail-to-rail
Output Common-Mode Range Rail-to-rail
工作溫度範圍 0 °C to +70 °C
封裝 8-pin SOIC
安裝類型 Surface mount
RoHS 狀態 Compliant

TLV2762CD 腳位配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
腳位 1 OUTA — Channel A output
腳位 2 IN-A — Channel A inverting input
腳位 3 IN+A — Channel A non-inverting input
腳位 4 V- — Negative supply connection
腳位 5 IN+B — Channel B non-inverting input
腳位 6 IN-B — Channel B inverting input
腳位 7 OUTB — Channel B output
腳位 8 V+ — Positive supply connection

典型應用

TLV2762CD 適用於 6 應用s: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Low-Voltage Control, Portable Data Acquisition, Low-Voltage Current Measurement, Active Filtering and Level Shifting.

📱

Battery-Powered Sensor Conditioning

The TLV2762CD fits low-voltage sensor front ends because it operates from 1.8 V to 3.6 V, consumes 20 µA typical supply current per amplifier, and accepts or produces signals near either supply rail. Place the dual channels around a resistive sensor bridge to buffer the excitation outputs and amplify the differential measurement at the input stage. Rail-to-rail operation preserves much of the signal range in compact battery-powered products. The 500 kHz bandwidth supports moderate-bandwidth filtering, while the 95 nV/√Hz input-noise density helps preserve weak sensor signals. Check source-impedance-induced error and the final amplifier saturation limits before fixing the gain.

💊

Portable Medical Monitoring

The TLV2762CD is appropriate for portable monitoring modules that require low-noise amplification from a 1.8 V or 3.3 V rail. Its 95 nV/√Hz input-voltage noise density and 15 pA typical input-bias current are useful when processing low-amplitude physiological or biochemical signals, while the two channels can provide gain and active filtering. The 500 kHz bandwidth allows response beyond the bandwidth of many slow sensor signals without requiring a high-current amplifier. Rail-to-rail input and output behavior improves usable signal span in compact wearables. Validate noise, settling time, patient-safety isolation, and the complete analog front end for the intended measurement class.

🏭

Industrial Low-Voltage Control

The TLV2762CD can condition low-level control signals in 3.3 V industrial systems where rail-to-rail operation and low supply current are useful. Its dual channels can amplify a sensor output and provide an active filter or level-shifting stage for a controller input. The 1.8 V to 3.6 V operating range supports both 1.8 V and 3.3 V rails, and 500 kHz bandwidth handles many process-control signals with modest speed requirements. For industrial use, review the commercial 0 °C to +70 °C limit and select an industrial-temperature grade when the enclosure temperature can exceed that range. Also confirm the grounding and isolation arrangement for the deployed equipment.

🖥️

Portable Data Acquisition

The TLV2762CD suits compact, low-voltage data-acquisition systems requiring two analog channels, rail-to-rail signal handling, and modest bandwidth. Its 500 kHz unity-gain bandwidth supports conditioning of temperature, pressure, position, and slow vibration sensors without the higher supply demand of a 10 MHz amplifier. The 20 µA typical supply current helps preserve battery life, while 95 nV/√Hz noise density supports low-amplitude measurements. Use one channel for gain and one for filtering or active offset correction when appropriate. Choose external precision resistors and an anti-alias filter based on the sensor bandwidth, because the amplifier itself does not determine the final acquisition accuracy.

⚡

Low-Voltage Current Measurement

The TLV2762CD can amplify the output of a low-side current shunt in a 3.3 V supply design. Its rail-to-rail input stage accepts shunt voltages near the lower or upper rail, and the dual-channel configuration can provide differential gain followed by filtering or a second signal path. With 95 nV/√Hz input-voltage noise density, it is suitable for many precision current measurements where the shunt impedance and amplifier gain determine the useful resolution. The 500 kHz bandwidth supports faster transient capture than a static precision amplifier. Keep shunt and feedback traces short, use a Kelvin connection where possible, and verify input common-mode behavior under maximum current before production release.

🔧

Active Filtering and Level Shifting

The TLV2762CD is useful for implementing active filters and level-shifting stages in portable analog systems. Its rail-to-rail output allows the conditioned signal to approach the positive or negative supply more closely than a conventional amplifier, improving utilization of a 1.8 V or 3.3 V rail. The 500 kHz bandwidth supports moderate-frequency filter sections, and the 230 V/ms slew rate reduces large-signal distortion. The two channels allow cascading filter stages when the calculated Q and stability requirements permit it. Use resistor and capacitor values that remain appropriate for the intended gain, check the closed-loop response across temperature, and place feedback components close to the device to minimize parasitic feedback.

What is the operating voltage range of the TLV2762CD?
The TLV2762CD operates from a single 1.8 V to 3.6 V supply. According to the Texas Instruments TLV2762 product information, both amplifier channels support rail-to-rail input and output operation within that low-voltage range. The 3.6 V maximum also makes the device suitable for systems powered directly from a single-cell lithium-ion battery after appropriate voltage regulation.
What are the key specifications of TLV2762CD that engineers should know?
The TLV2762CD combines two amplifiers, a 1.8 V to 3.6 V supply range, 500 kHz unity-gain bandwidth, and rail-to-rail input/output operation in an 8-pin SOIC. Its principal analog characteristics include 230 V/ms slew rate, 95 nV/√Hz input-voltage noise density, 550 µV typical input-offset voltage, 15 pA typical input-bias current, and 20 µA typical supply current per amplifier.
Where can I download the TLV2762CD datasheet PDF?
The official TLV2762CD technical information is available through the Texas Instruments product page at https://www.ti.com/product/TLV2762. From that page, select the TLV2762CD ordering option and open the associated datasheet documentation. The device is also identified as TLV2762CD in the manufacturer ordering table, which links the 8-pin SOIC configuration to its technical limits and package information.
Where can I find the TLV2762CD pinout?
The TLV2762CD pinout is documented in the pin-configuration section of the Texas Instruments TLV2762 datasheet. The 8-pin SOIC uses a standard dual-operational-amplifier arrangement: pins 1 and 7 are the two amplifier outputs, pins 2 and 6 are inverting inputs, pins 3 and 5 are non-inverting inputs, pin 4 is the negative supply, and pin 8 is the positive supply. Use the manufacturer diagram when assigning PCB tracks.
Is the TLV2762CD suitable for battery-powered sensor applications?
The TLV2762CD is suitable for low-voltage battery-powered sensing because it operates down to 1.8 V and draws 20 µA typical supply current per amplifier. Its rail-to-rail inputs and outputs preserve signal range within a restricted supply, while the 500 kHz bandwidth is sufficient for many filtered sensor signals. Confirm the source impedance, settling requirements, and total system leakage before finalizing the power budget.
What can replace the TLV2762CD on the same PCB?
The TLV2762ID is the closest same-package drop-in candidate because it uses the same 8-pin SOIC outline and provides the same dual rail-to-rail amplifier architecture over the same 1.8 V to 3.6 V supply range. Its principal difference is the wider -40 °C to +85 °C operating-temperature range. Verify enable, shutdown, noise, and stability requirements before using it in a design originally specified around TLV2762CD.
Is TLV2762CD the same as TLV2762ID?
No. TLV2762CD and TLV2762ID share the dual 8-pin SOIC configuration and the same fundamental low-voltage rail-to-rail amplifier function, but their temperature grades differ. TLV2762CD is specified from 0 °C to +70 °C, whereas TLV2762ID is intended for the wider industrial range of -40 °C to +85 °C. The wider grade makes TLV2762ID the preferred choice when the enclosure cannot guarantee commercial-temperature operation.
TLV2762CD vs TLV2762ID: which is better for an industrial controller?
TLV2762ID is generally better for an industrial controller because it supports -40 °C to +85 °C, while TLV2762CD is limited to 0 °C to +70 °C. Both use the 8-pin SOIC package and are based on the same 1.8 V to 3.6 V dual rail-to-rail amplifier family. Choose the commercial-temperature part only when every system temperature condition remains inside its 0 °C to +70 °C rating.
When should I choose TLV2762CD over TLV2762ID?
Choose TLV2762CD when the application is guaranteed to remain between 0 °C and +70 °C and the assembly does not require industrial-temperature screening. Choose TLV2762ID instead when the board may operate below 0 °C or above +70 °C. Because both devices use the same 8-pin SOIC outline, temperature qualification is the principal decision criterion rather than PCB redesign.
What is the best Texas Instruments equivalent for TLV2762CD?
The TLV2762ID is the best-supported same-manufacturer equivalent identified for a footprint-compatible replacement. It retains the dual low-voltage rail-to-rail architecture, 1.8 V to 3.6 V supply capability, and 8-pin SOIC package while extending the operating range to -40 °C to +85 °C. Confirm stability with the output-load network and verify all timing and noise requirements before substitution.
Where to buy TLV2762CD online?
Use the Request a Quote form on this page to request TLV2762CD availability, current commercial terms, and order handling from XAIPART. The request should identify the 8-pin SOIC configuration, operating-temperature grade, and required quantity. This avoids relying on a stale catalog amount and lets the order be checked against the current manufacturer and channel position.
What is the price of TLV2762CD?
Current pricing for TLV2762CD should be requested through the Request a Quote form on this page. The form allows the exact 8-pin SOIC part number and quantity to be checked against the current supply position. No fixed amount is stated here because commercial pricing and quantity availability can change independently of the device's electrical characteristics.
What is the lead time for TLV2762CD?
Request the current lead time through the Request a Quote form on this page and include your required quantity and production schedule. Lead time can vary with order volume, assembly packaging, and current component availability, so it should be confirmed for the exact TLV2762CD ordering option rather than inferred from another package or reel format.
Is TLV2762CD in stock?
Current TLV2762CD stock status should be confirmed through the Request a Quote form on this page. Provide the quantity, target date, and whether the standard 8-pin SOIC tube configuration is acceptable. The manufacturer lists the TLV2762 family as active, but current inventory is a transactional condition and should not be inferred solely from lifecycle status.
How much noise does the TLV2762CD contribute to a precision amplifier stage?
The TLV2762CD has an input-voltage noise density of 95 nV/√Hz at 1 kHz, allowing low-noise amplification of signals from high-impedance sensors. Its typical input-bias current of 15 pA also limits bias-current error with high-source-impedance sensors. Actual stage noise depends on resistor values, source impedance, bandwidth, and the operating mode, so calculate those values for the complete amplifier network.
Can TLV2762CD drive a capacitive load?
The TLV2762CD can drive suitable capacitive loads, but the exact load, output stage, and stability behavior must be checked for the operating condition. Place the feedback network close to the amplifier pins and isolate unusually capacitive loads from the output when necessary. Series resistance and an additional compensation capacitor are common methods for maintaining stability without materially increasing noise.

工程參考資料,適用於 TLV2762CD — 比較、設計指引及合規資訊。

選型指南

Choose TLV2762CD for a 1.8 V or 3.3 V dual-amplifier design whose operating temperature remains between 0 °C and +70 °C. Its 500 kHz bandwidth, 20 µA typical supply current, 95 nV/√Hz input-noise density, and rail-to-rail operation are well suited to portable sensing, active filtering, and low-voltage control. Choose TLV2762ID when the same electrical architecture and 8-pin SOIC footprint are needed in an industrial-temperature environment. Consider TLV2772CD or TLV2772ID when their higher bandwidth is justified, but verify their minimum supply voltage, noise, supply current, and output behavior against the system requirements. A footprint-compatible package does not by itself guarantee equivalent AC, noise, common-mode, or stability performance, so compare the manufacturer characteristic data before releasing a substitution.

與替代品比較

參數 本產品 TLV2762ID TLV2772CD TLV2772ID
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC - same footprint 8-pin SOIC - same footprint 8-pin SOIC - same footprint
Amplifier Configuration Dual Dual Dual Dual
Operating Temperature 0 °C to +70 °C -40 °C to +85 °C 0 °C to +70 °C -40 °C to +85 °C
Input and Output Range Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail

主要差異化特點

  • Commercial-temperature drop-in simplicity (對比TLV2762ID)
  • Low supply current with usable bandwidth (對比TLV2772CD)
  • High-impedance signal conditioning (對比TLV2772ID)

設計說明

Place the supply bypass capacitor immediately between the V+ and V- pins. Keep the supply trace short, connect the capacitor ground directly to the device ground, and use a separate return path for input and feedback currents. Because the device can operate down to 1.8 V, verify that every upstream rail remains within the operating range during startup, shutdown, and load transients.

Keep the two inverting-input feedback components close to pins 2 and 6 to minimize parasitic capacitance and unwanted feedback. Route the non-inverting inputs away from supply, clock, and high-current switching nodes. For sensitive measurements, use a ground plane that remains continuous beneath the amplifier and separate analog input routing from digital return currents.

Check output stability with the actual load, including cable capacitance, probe capacitance, and the input capacitance of the following stage. If ringing appears, reduce the capacitive load or add a small isolation resistor at the output. Recalculate the gain and bandwidth after adding compensation so that the final closed-loop response still meets the signal-chain requirements.

Rail-to-rail input does not eliminate input-bias-current error when driving a high source impedance, and rail-to-rail output does not eliminate the need to observe output swing limits. Use the manufacturer characteristic curves to confirm input common-mode range and output voltage under the actual load. Also confirm the ambient temperature against the 0 °C to +70 °C rating before using TLV2762CD in an industrial enclosure.

合規資訊

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The product listing identifies the TLV2762CD as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or automotive qualification statement was identified.

相關搜尋

TLV2762CD datasheet TLV2762CD datasheet pdf TLV2762CD pinout TLV2762CD specifications Texas Instruments TLV2762CD TLV2762CD replacement TLV2762CD equivalent TLV2762CD cross reference TLV2762CD vs TLV2762ID TLV2762CD footprint TLV2762CD price TLV2762CD stock TLV2762CD sensor amplifier TLV2762CD application circuit TLV2762 1.8V dual RRIO amplifier

相關元件與詞彙

Texas Instruments TLV2762CD TLV2762ID TLV2772CD TLV2772ID operational amplifier dual amplifier rail-to-rail input rail-to-rail output low-dropout voltage regulator micropower amplifier unity-gain bandwidth input-voltage noise density input-bias current input offset voltage slew rate signal conditioning active filter battery-powered electronics SOIC-8 surface-mount package RoHS 3.6 V 1.8 V 500 kHz
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情