VSC8552XKS-04 - Dual-Port Gigabit Ethernet PHY | Microchip
MPN: VSC8552XKS-04 ✗ জীবনকালের সমাপ্তিVSC8552XKS-04 সারাংশ
A Gigabit Ethernet PHY is a physical-layer transceiver that converts digital data into electrical signals for transmission over copper cabling and reconstructs received signals for the associated media-access controller. Within the Ethernet hierarchy, a PHY sits below the MAC layer and above the physical cable interface. The VSC8552 therefore belongs to the interface-IC and network-interface categories rather than the processor or switching-controller categories. Its two independent Gigabit Ethernet ports support equipment that requires two physical network connections within one device.
The principal published features of the VSC8552 include dual-port Gigabit Ethernet operation and EcoEthernet IEEE 802.3az Energy Efficient Ethernet technology. IEEE 802.3az allows a compliant link to reduce power consumption when network traffic is light. A nominal 1 V core supply supports integration into modern high-speed digital equipment, while the automotive-grade temperature range allows operation from -40 °C to +125 °C in demanding environmental conditions.
The 256-PBGA package provides 256 bottom-side terminals on a 17 mm by 17 mm square body. This dense land pattern can reduce board footprint but requires careful escape routing, via planning, and power-distribution design. Because the package combines two PHYs and a high pin count, PCB signal-integrity and thermal performance depend heavily on layer count, return paths, via geometry, and layout symmetry. The nominal 1 V supply should be distributed through low-impedance power and ground planes rather than narrow traces.
Typical uses include automotive Ethernet gateways, vehicle network interfaces, industrial communication equipment, dual-port embedded systems, and access-network equipment. The dual-port architecture is particularly useful when one product must offer two copper Ethernet connections without using two separate PHY packages. The manufacturer identifies enterprise networks, data centers, and consumer electronics as VSC8552 application areas, while the automotive-temperature version is suited to vehicle electronics and other extended-temperature systems.
The primary design consideration is that a valid replacement must match the 256-terminal PBGA footprint, ball map, supply requirements, clocking, register behavior, and Ethernet application requirements. The VSC8552XKS-05 is identified as an alternative catalog part in the same 17 mm by 17 mm 256-PBGA format, but firmware, feature, and lifecycle differences still need confirmation before it is treated as an unconditional production substitute.
This page combines the manufacturer positioning, package and environmental characteristics, drop-in candidate review, comparison data, and practical design considerations into an engineering-oriented overview of the VSC8552XKS-04.
এর জন্য ড্রপ-ইন বিকল্প VSC8552XKS-04 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
VSC8552XKS-05
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
VSC8552XKS-04 বিশেষণ
| Product Type | Dual-port Gigabit Ethernet PHY transceiver |
| Number of Ethernet Ports | 2 ports |
| Ethernet Speed | Gigabit Ethernet |
| Nominal Supply Voltage | 1 V |
| অপারেটিং তাপমাত্রার পরিসর | -40 °C to +125 °C |
| Package Type | 256-terminal PBGA |
| Package Dimensions | 17 mm x 17 mm |
| Terminal Count | 256 terminals |
| Terminal Location | Bottom side |
| মাউন্টিং টাইপ | Surface mount |
| Energy Efficient Ethernet Standard | IEEE 802.3az |
| Manufacturer Product Family | VSC8552 series |
| Product Category | Ethernet interface IC |
| অপারেটিং সাপ্লাই ভোল্টেজ | 1 V nominal |
| Package Shape | Square |
| Terminal Form | Ball |
VSC8552XKS-04 square পিন কনফিগারেশন গাইড
VSC8552XKS-04 (square প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি VSC8552XKS-04.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
VSC8552XKS-04 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Automotive Ethernet Gateway, Industrial Dual-Port Communication Equipment, Enterprise Network Edge Device, Data Center Network Interface, Vehicle Network Backbone Node, Consumer Network Gateway.
Automotive Ethernet Gateway
The VSC8552XKS-04 fits an automotive Ethernet gateway that must provide two network connections while operating across an extended temperature range of -40 °C to +125 °C. Its dual-port Gigabit Ethernet PHY architecture consolidates two physical channels into one 17 mm by 17 mm device, which can simplify board partitioning compared with two separate PHY packages. The nominal 1 V core supply is suited to tightly regulated automotive digital rails, while IEEE 802.3az support can reduce link activity during idle periods. The design should preserve continuous ground references beneath the BGA, use short supply connections, and validate magnetics and channel compliance in the final vehicle-network design.
সুপারিশকৃত
Industrial Dual-Port Communication Equipment
The VSC8552XKS-04 is suitable for industrial communication equipment requiring two Gigabit Ethernet physical interfaces in a high-density package. Its -40 °C to +125 °C operating range supports equipment deployed in factories, control cabinets, and outdoor systems where ambient conditions exceed consumer-grade limits. Integrating two PHYs can reduce component count and connector-adjacent routing congestion, although the 256-terminal PBGA requires disciplined via-in-pad and escape-routing strategies. IEEE 802.3az support can lower power consumption when traffic is intermittent, making the device useful for monitoring stations and industrial gateways that must remain network-accessible without maintaining maximum link activity continuously.
সুপারিশকৃত
Enterprise Network Edge Device
The VSC8552 can support edge equipment requiring two Gigabit Ethernet links, such as an access controller or compact network interface module. Its dual-port configuration allows separate uplink and service connections without duplicating the physical-layer circuitry footprint. IEEE 802.3az Energy Efficient Ethernet is particularly relevant in enterprise networks where link idle periods can be frequent, although energy performance must be confirmed with the system link partner and network configuration. The 17 mm by 17 mm PBGA offers high pin density but can increase assembly and inspection complexity, so designers should evaluate thermal spreading, BGA assembly capability, and high-speed layer transitions during hardware qualification.
সুপারিশকৃত
Data Center Network Interface
The VSC8552XKS-04 is applicable to specialized data-center network-interface equipment that needs two compact Gigabit Ethernet physical ports. Integrating both ports into one package may simplify enclosure space and provide a consistent PHY implementation across two connections. Its nominal 1 V operating supply aligns with modern high-speed digital power architecture, while EcoEthernet IEEE 802.3az can support power-control objectives in links with variable traffic. In a data-center product, however, thermal design and signal integrity remain critical: high pin-count BGA escape routes can couple aggressors into Ethernet channels, so layer transitions, return paths, magnetics placement, and connector-to-PHY differential routing should be validated using the manufacturer layout guidance.
সুপারিশকৃত
Vehicle Network Backbone Node
The VSC8552XKS-04 can serve as the physical-layer element in a vehicle network node that requires two Gigabit Ethernet connections. The -40 °C to +125 °C rating is directly relevant to automotive environmental conditions, and the dual-port organization can support bridging, diagnostic, or service-facing links within one controller. The nominal 1 V supply should be generated from an appropriately regulated automotive rail and filtered close to the BGA power terminals. Because the device is a high-density PBGA, thermal cycling, solder-joint reliability, and differential-channel performance should be evaluated in the final enclosure and wiring environment rather than inferred from the component rating alone.
সুপারিশকৃত
Consumer Network Gateway
The VSC8552 family is identified by Microchip for consumer electronics as well as enterprise and data-center systems, making its dual-port PHY suitable for compact routers, media gateways, and connected home equipment. Two Gigabit Ethernet ports can support wired uplink and local-device connectivity in a single package. IEEE 802.3az can reduce power use when one link is lightly loaded, while the 256-terminal PBGA helps contain board area despite a large ball count. Consumer-product implementations still need careful separation between Ethernet differential pairs, clocking domains, and switching or processor supplies. The manufacturer reference layout and channel-compatibility testing should guide magnetics placement, connector clearances, and thermal verification.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা VSC8552XKS-04 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | VSC8552XKS-05 |
|---|---|---|
| Package | 256-PBGA (17 mm x 17 mm) | 256-PBGA (17 mm x 17 mm) |
| Brand | Microchip Technology | Microchip Technology |
| Product Type | Dual-port Gigabit Ethernet PHY | Ethernet transceiver |
| Nominal Supply Voltage | 1 V | 1 V |
| Terminal Count | 256 terminals | 256 terminals |
| Package Dimensions | 17 mm x 17 mm | 17 mm x 17 mm |
মূল পার্থক্যসমূহ
- Same documented 256-PBGA mechanical format (বনামVSC8552XKS-05)
- Identical nominal core supply (বনামVSC8552XKS-05)
- Documented same-series replacement candidate (বনামVSC8552XKS-05)
ডিজাইন নোট
Use the exact manufacturer land pattern and ball map for the 256-terminal PBGA rather than a generic BGA-256 footprint. A 17 mm square package leaves little room for arbitrary escape routing, so place Ethernet magnetics and their supporting networks close to the relevant PHY balls. Maintain a continuous ground reference beneath the device, avoid splits across any layer carrying high-speed signals, and route each differential pair as a tightly coupled pair with matched impedance.
Distribute the nominal 1 V supply through low-impedance power and ground planes, with local high-frequency bypass capacitors placed according to the manufacturer reference layout. Decoupling should be located close to the associated BGA power and ground terminals rather than at the system supply connector. Validate power sequencing, startup behavior, voltage tolerance, and the interaction between the PHY rails and any external processor or MAC supplies before releasing the PCB.
Treat each Gigabit Ethernet channel as a controlled-impedance differential route and keep it away from switching supplies, clocks, and unrelated high-speed traffic. The two PHY ports should have symmetric reference layouts to reduce channel-to-channel variation. Check connector, magnetics, and PCB losses together rather than validating them independently, and use the manufacturer's channel and layout guidance to set termination, biasing, and isolation requirements.
A 17 mm by 17 mm BGA can introduce substantial heat-flow distance from its center to the PCB, particularly at the 1 V core rail. Use uninterrupted ground planes and a layer stack that provides effective heat spreading, then evaluate junction and board temperatures in the maximum-activity enclosure condition. The -40 °C to +125 °C component rating does not by itself guarantee adequate system cooling or solder-joint reliability across the complete temperature range.
Do not approve a replacement solely because both devices use a 256-terminal PBGA. Verify the ball map, supply pins, clock requirements, register behavior, initialization sequence, firmware expectations, and qualification status. Also check Microchip product-change and end-of-life notices because the VSC85xx series is associated with lifecycle transitions. A mechanical footprint match is necessary for drop-in use but is not sufficient for functional equivalence.
কমপ্লায়েন্স তথ্য
The part is identified as an automotive-temperature Ethernet transceiver operating from -40 °C to +125 °C, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements were not included in the cited product records.