XC9572XL-7VQG44C 72-Macrocell CPLD, 5 ns, 44 VQFP | AMD
MPN: XC9572XL-7VQG44C ✗ জীবনকালের সমাপ্তিXC9572XL-7VQG44C সারাংশ
A CPLD, or complex programmable logic device, is a user-programmable semiconductor that combines non-volatile configuration memory with interconnected logic arrays. In the product hierarchy, a CPLD belongs to programmable logic devices alongside FPGAs and other logic devices. It sits below a microcontroller in general-purpose processing capability, but offers deterministic hardware logic that continues operating without software execution. The XC9500XL architecture is intended for compact control, interface, decoding, and glue-logic designs.
Key features of the XC9572XL-7VQG44C include four 54V18 function blocks, 72 macrocells, 1,600 usable gates, 34 user I/O pins, 5 ns pin-to-pin logic delays, and operation from a 3.3 V core supply. The 44-pin VQFP format supports a compact surface-mount implementation, while the -7 grade favors timing performance over the slower -10 variant. Non-volatile configuration storage allows the programmed logic design to remain available after power is removed.
The XC9500XL architecture is optimized for high-performance communications and computing systems. Each macrocell provides programmable combinational and registered logic, allowing control signals, state machines, bus decoding, protocol interfaces, and data-routing functions to be consolidated into one programmable device. The family provides substantially more logic capacity than basic GAL-type devices while maintaining a comparatively simple programming workflow and a modest 72-macrocell footprint.
Typical uses include industrial control interfaces, communications equipment, test and measurement systems, peripheral controllers, legacy bus interface logic, and embedded system support functions. A design can use the 34 available I/O pins for external data buses, control signals, status indicators, and clocked interfaces. The 178 MHz system-frequency figure describes the supported logic performance class, while the 5 ns pin-to-pin delay provides the more useful timing target for many board-level designs.
Designers should verify signal-integrity and timing requirements against the manufacturer data sheet, especially for high-speed outputs, external memory interfaces, and fanout-sensitive nets. The 44-pin surface-mount package also requires careful PCB footprint and thermal assessment. Because this device uses an established programmable-logic family, existing designs may require Xilinx or AMD ISE-compatible project files and supported programming hardware.
This product record combines the manufacturer data sheet with focused engineering guidance, package information, lifecycle context, and pin-compatible alternatives. It also highlights the timing, I/O, and capacity differences that matter when replacing a CPLD without changing the PCB footprint.
এর জন্য ড্রপ-ইন বিকল্প XC9572XL-7VQG44C — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible XC9572XL-7VQG44C (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Product Type, Usable Gates.
XC9572XL-10VQG44C
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
XC9572XL-5VQG44C
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
XC9572XL-10VQG44I
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
XC9572XL-7VQG44I
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
XC9572XL-7VQG44C সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | High-performance CPLD |
| Device Family | XC9500XL |
| Core Supply Voltage | 3.3 V |
| Macrocells | 72 macrocells |
| Usable Gates | 1,600 usable gates |
| Function Blocks | 4 function blocks |
| Function Block Architecture | 54V18 |
| User I/O Pins | 34 user I/O pins |
| Pin-to-Pin Logic Delay | 5 ns |
| Maximum System Frequency | 178 MHz |
| প্যাকেজ | 44-pin VQFP |
| Speed Grade | -7 |
| Temperature Grade | Industrial grade |
| মাউন্টিং টাইপ | Surface mount |
| Configuration Technology | Non-volatile configuration memory |
| Process Technology | 0.35 um CMOS |
XC9572XL-7VQG44C 44-pin vqfp পিন কনফিগারেশন গাইড
XC9572XL-7VQG44C (44-pin vqfp প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি XC9572XL-7VQG44C.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
XC9572XL-7VQG44C এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Communications Protocol Interfaces, Industrial Control Logic, Test and Measurement Systems, Legacy Bus Interface Bridges, Embedded Peripheral Controllers, Peripheral and Storage Support Logic.
Communications Protocol Interfaces
The XC9572XL-7VQG44C suits communications equipment requiring deterministic protocol framing, command decoding, and interface control without a processor performing every I/O operation. Its four 54V18 function blocks provide 72 macrocells and 1,600 usable gates, while the 5 ns pin-to-pin delay supplies useful timing margin for registered state-machine logic. Thirty-four user I/O pins can support data, clock, chip-select, and handshake signals. The 3.3 V architecture aligns with modern low-voltage communications logic, although external line drivers or level translators may still be required for physical interfaces.
সুপারিশকৃত
Industrial Control Logic
The XC9572XL-7VQG44C is appropriate for compact industrial controllers that combine sequencing, interlocks, status decoding, and peripheral control in programmable hardware. The 72-macrocell capacity can consolidate multiple small state machines, and the -7 speed grade provides a 5 ns pin-to-pin logic delay for faster control paths. Thirty-four user I/O pins support sensors, actuator commands, and machine-status signals at suitable logic levels. For industrial deployment, verify the exact operating-temperature limits, isolation requirements, and safety controls beyond the CPLD itself.
সুপারিশকৃত
Test and Measurement Systems
A CPLD is useful in test and measurement equipment for trigger sequencing, instrument-control decoding, status aggregation, and deterministic timing generation. The XC9572XL-7VQG44C combines 34 user I/O pins with a 5 ns logic delay, allowing several control functions to be implemented in one programmable device without relying on continuous software servicing. Its non-volatile configuration also preserves the control design across power cycles. Engineers should use the data-sheet timing specifications to establish setup, hold, clock, and output-loading margins for precision trigger paths.
সুপারিশকৃত
Legacy Bus Interface Bridges
The XC9572XL-7VQG44C can bridge or adapt older parallel buses where a compact, non-volatile controller is preferable to a larger processor subsystem. Its macrocell resources support address decoding, read and write sequencing, arbitration, and data-path gating, while 34 user I/O pins can accommodate address, control, and a portion of the data bus. The 5 ns delay class helps preserve timing margin in synchronous control paths. Final implementation requires careful analysis of bus direction changes, contention, termination, and every device’s setup and hold timing.
সুপারিশকৃত
Embedded Peripheral Controllers
The XC9572XL-7VQG44C can act as a dedicated peripheral controller in an embedded system, implementing command sequencing, interrupt logic, display multiplexing, keypad scanning, or I/O expansion independently of the main processor. Its four function blocks and 72 macrocells allow related logic sections to be mapped without a large FPGA, while the 34 I/O pins provide connections to external devices. The -7 grade offers stronger timing margin than the -10 option. The programmer and JTAG programming chain must remain supported by the selected AMD or Xilinx ISE workflow.
সুপারিশকৃত
Peripheral and Storage Support Logic
The XC9572XL-7VQG44C is suitable for auxiliary logic around processors, storage controllers, and peripheral chips where local decoding and sequencing must operate predictably. Programmable macrocells can implement command qualification, FIFO-handshake control, interrupt masking, and address decoding, reducing dependence on host software for time-critical tasks. The 44-pin VQFP footprint supports compact board layouts, and the 3.3 V core supply integrates with compatible logic. Designers should confirm output-current limits, bus contention behavior, and storage-interface timing against the relevant device data sheets.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা XC9572XL-7VQG44C — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | XC9572XL-10VQG44C | XC9572XL-5VQG44C | XC9572XL-10VQG44I | XC9572XL-7VQG44I |
|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD |
| Package | VQFP-44 | VQFP-44 - same | VQFP-44 - same | VQFP-44 - same | VQFP-44 - same |
| Device Architecture | XC9572XL | XC9572XL | XC9572XL | XC9572XL | XC9572XL |
| Macrocells | 72 macrocells | 72 macrocells | 72 macrocells | 72 macrocells | 72 macrocells |
| Usable Gates | 1,600 usable gates | 1,600 usable gates | 1,600 usable gates | 1,600 usable gates | 1,600 usable gates |
| User I/O Pins | 34 user I/O pins | 34 user I/O pins | 34 user I/O pins | 34 user I/O pins | 34 user I/O pins |
| Core Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Speed Grade | -7, 5 ns pin-to-pin logic delay | -10, slower speed class | -5, faster speed class | -10, slower speed class | -7, 5 ns pin-to-pin logic delay |
| Temperature Suffix | C - commercial | C - commercial | C - commercial | I - industrial | I - industrial |
| Function Blocks | 4 function blocks | 4 function blocks | 4 function blocks | 4 function blocks | 4 function blocks |
মূল পার্থক্যসমূহ
- Balanced -7 speed and commercial-temperature ordering (বনামXC9572XL-7VQG44I)
- Timing performance between the slower and faster speed grades (বনামXC9572XL-10VQG44C)
- Lower-delay option remains footprint compatible (বনামXC9572XL-5VQG44C)
- Commercial-temperature option for standard environments (বনামXC9572XL-10VQG44I)
ডিজাইন নোট
Do not select a replacement solely because the package drawing matches. The XC9572XL-10 and XC9572XL-5 options change the speed class, while the I option changes the temperature grade. Validate the complete timing budget, operating-temperature range, pin functions, and programming configuration for each ordering code. Re-run implementation and static timing analysis after changing speed or temperature variants rather than assuming the target device's constraints apply unchanged.
Use the 44-pin VQFP land pattern and pin-1 orientation from AMD data sheet DS057 when laying out the PCB. Place decoupling structures close to the appropriate supply pins and route the 34 user I/O signals away from fast-switching or high-current paths where practical. Because no exposed-pad construction is identified for this package, do not assign an exposed-pad thermal land without confirming it in the official package drawing.
Evaluate every high-speed or heavily loaded net against the output-current, rise-time, and capacitive-loading limits in the XC9572XL data sheet. Add series damping only after accounting for the actual receiver and trace loading, and avoid long stubs between the CPLD and external devices. The 5 ns pin-to-pin logic delay does not by itself guarantee system-level timing; external device delays, trace skew, setup time, and hold time must also be included.
Keep programming and configuration signals away from noisy analog or switching circuitry, and provide a stable 3.3 V supply with local high-frequency bypass capacitors. Review ground-return paths so output switching currents do not share narrow return paths with sensitive logic. For systems combining the CPLD with external memory or transceivers, use the manufacturer pin assignments and timing constraints to separate data, clock, and control routing where the implementation permits.
Estimated: the CPLD's actual dissipation depends on logic activity, output loading, supply voltage, and the package thermal environment, none of which is established by the available family-level information. Evaluate it with the actual switching workload and the board’s copper area instead of applying a generic thermal figure. Keep the device within its specified ambient and junction limits, and provide airflow or copper spreading where the enclosure raises the local temperature.
কমপ্লায়েন্স তথ্য
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was established for the exact ordering code. The G suffix identifies the industrial-temperature option in this family, but it does not itself establish AEC-Q100 qualification.