Integrated Circuits

Subcategories

📁 ADC/DAC 3,100+ products 📁 Amplifier ICs 1,900+ products 📁 Audio Codecs 18 products 📁 Audio ICs 2 products 📁 Clock & Timing 660+ products 📁 Comparator ICs 1 products 📁 DSP 1,100+ products 📁 Data Acquisition ICs 2 products 📁 Digital Potentiometers 4 products 📁 Display Drivers & Controllers 1 products 📁 FPGA & CPLD 7,300+ products 📁 Interface ICs 3,300+ products 📁 LED Drivers 1 products 📁 Logic ICs 460+ products 📁 Memory ICs 870+ products 📁 Microcontrollers 20,000+ products 📁 Microprocessors 4 products 📁 Motor Drivers 1 products 📁 Other 1 products 📁 Sensor and Detector Interfaces 1 products 📁 Specialized ICs 15 products 📁 Video ICs 14 products

Products (39,000+)

PIC24F08KL302T-I/SS - 16-bit 8KB Flash MCU, 32MHz XLP | Microchip
PIC24F08KL302T-I/SS

PIC24F08KL302T-I/SS - 16-bit 8KB Flash MCU, 32MHz XLP | Microchip

The Microchip PIC24F08KL302T-I/SS is a 16-bit Flash microcontroller from the PIC24F KL3 family featuring nanoWatt XLP eXtreme Low Power technology, 8KB of Flash program memory (2.75K x 24 words), 1KB of data SRAM, and a 10-bit ADC with up to 12 input channels. It operates at 32MHz (8 MIPS) from a 1.8V to 3.6V supply in a 28-pin SSOP package and is rated for the industrial -40C to +85C temperature range. A PIC24F microcontroller is a 16-bit RISC MCU built on Microchip's enhanced Harvard architecture; the KL3 sub-family targets cost-sensitive applications by migrating familiar PIC18 peripherals (MSSP I2C/SPI, CCP/ECCP, 10-bit ADC) into the 16-bit core, allowing engineers to leverage existing PIC18 firmware libraries while gaining higher throughput and a wider instruction set. It sits within the broader hierarchy: microcontroller -> embedded MCU -> semiconductor. Key features include 256 bytes of EEPROM data memory, 3x 16-bit timers, 2x analog comparators with selectable reference, 1x UART, 1x I2C, 1x SPI, and ultra-low-power sleep modes (deep sleep current typically below 100 nA). The nanoWatt XLP technology delivers active current around 8 uA/MHz, enabling years of battery life in always-on edge devices. Architecture-wise, the device uses a modified Harvard bus with separate program and data paths, hardware multiply, and a deterministic interrupt controller. The 32MHz internal oscillator eliminates the need for an external crystal in many cost-optimized designs, while a 4x PLL is selectable for higher instruction throughput. Typical applications include low-cost IoT sensor nodes, battery-powered consumer devices, white goods and small home appliances, HVAC accessories, metering peripherals, and PIC18 migration designs. Designers choose this part when 8-bit PIC18 performance is insufficient but full PIC24EP cost is not required. A key design tip is to use the 32MHz internal Fast RC oscillator with the PLL to save BOM cost, and to leverage the deep-sleep watchdog and RTCC for sub-microamp sleep profiles. Carefully review the configuration bits in the IDE to enable the correct oscillator mode before code generation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC24F08KL401-E/MQ - 16-Bit 8KB MCU | Microchip
PIC24F08KL401-E/MQ

PIC24F08KL401-E/MQ - 16-Bit 8KB MCU | Microchip

The Microchip Technology PIC24F08KL401-E/MQ is a cost-sensitive 16-bit PIC24F microcontroller with 8 KB of Flash program memory, 1 KB of RAM, 512 bytes of EEPROM, and a maximum instruction rate of 16 MIPS at 32 MHz. The device is offered in a 20-VQFN surface-mount package with an exposed pad, identified by the /MQ package suffix, and operates from a 3 V supply according to distributor product data. A microcontroller is a programmable integrated circuit that combines a CPU core, memory, and peripherals in one package. The PIC24F family provides a compact embedded-control platform for cost-sensitive products that need more processing capability and peripheral flexibility than an 8-bit architecture. This product also includes nanoWatt XLP technology for eXtreme Low Power consumption, making it suitable for systems where standby energy use is an important design constraint. Key features include a 16-bit PIC24F core, 8 KB of Flash memory, 1 KB of RAM, 512 bytes of EEPROM, a 10-bit ADC, and a 12-channel ADC configuration. Peripheral integration includes MSSP support for I2C or SPI communication and CCP/ECCP modules for capture, compare, and PWM functions. These resources allow a compact design to combine control logic, analog measurement, communications, and timing functions without requiring separate peripheral devices. The 32 MHz maximum operating frequency supports an instruction execution rate of 16 MIPS, providing deterministic real-time control for compact embedded products. The 10-bit ADC supports conventional analog-to-digital conversion for sensing, while the MSSP module handles serial interfaces and the CCP/ECCP blocks support timing-sensitive functions. The exact ADC performance, channel details, and peripheral operating limits should be confirmed in the manufacturer datasheet. Typical uses include low-cost industrial controllers, compact sensor nodes, consumer appliances, battery-operated instruments, and small motor-control systems. The E/MQ ordering combination identifies the specified temperature and package configuration, while the -I/MQ version provides another verified ordering option with the same 20-VQFN footprint. Designers should place input and output decoupling capacitors close to the supply pins, connect the exposed thermal pad according to the land-pattern requirements, and confirm oscillator, programming, and peripheral assignments against the complete datasheet. This page combines verified product specifications, sourcing information, ordering guidance, and same-footprint replacement context for faster engineering evaluation.

RFQ Contact
PIC24F08KL401-E/P - 16-bit 32MHz 8KB Flash MCU | Microchip
PIC24F08KL401-E/P

PIC24F08KL401-E/P - 16-bit 32MHz 8KB Flash MCU | Microchip

The Microchip Technology PIC24F08KL401-E/P is a 16-bit PIC24F microcontroller with nanoWatt XLP eXtreme Low Power technology, featuring an 8KB Flash program memory and a 32MHz maximum CPU speed, housed in a 20-pin PDIP (0.300", 7.62mm) through-hole package. It integrates 1KB RAM, 512 bytes EEPROM, a 10-bit ADC, and PIC18-compatible peripherals such as MSSP (I2C/SPI) and CCP/ECCP, enabling easy migration from PIC18 designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. The PIC24F08KL401 belongs to the PIC24F family, a 16-bit modified Harvard architecture family that sits between the 8-bit PIC18 and the 32-bit PIC32 in Microchip's portfolio. It targets cost-sensitive embedded designs that need 16-bit performance, low power consumption, and easy migration from existing PIC18 firmware while staying below the price point of dsPIC or PIC32 devices. Key features include up to 32 MIPS performance from a 32MHz internal oscillator, the nanoWatt XLP power management unit with deep-sleep currents down to the sub-microamp range, and 25 MIPS sustained throughput at 3.3V. The 20-PDIP package offers wide prototyping-friendly pitch for breadboards and through-hole assembly, while industrial-grade -40C to +125C operation supports harsh-environment deployments. Architecturally, the PIC24F08KL401 uses a 16-bit modified Harvard core with a separate 24-bit instruction word and 16-bit data path. The MSSP peripheral supports both I2C and SPI on the same pins, while CCP/ECCP modules provide flexible PWM, capture, and compare functions. Hardware CRC, idle/sleep/doze modes, and brown-out reset (BOR) further enhance robustness in field-deployed embedded nodes. Typical applications include consumer electronics, industrial sensor nodes, low-power IoT endpoints, battery-powered HVAC controls, and white-goods motor control. The combination of XLP sleep currents, integrated ADC, and PIC18-compatible peripherals makes it especially attractive for retrofit designs and energy-harvesting devices. When designing with this MCU, ensure decoupling capacitors of 0.1uF and 10uF are placed near VDD/VSS pins, configure the CONFIG registers for the desired oscillator source during firmware initialization, and consult the family reference manual for the most recent silicon errata. Selecting the right ICSP programming header footprint preserves in-circuit debug capability across product revisions. This page synthesizes distributor pricing, drop-in package alternatives from the PIC24F and PIC24FJ families, and practical design considerations not found in the manufacturer datasheet, giving procurement and engineering teams a single reference for evaluation.

RFQ Contact
PIC24F08KL401-E/SO - 16-bit 32MHz 8KB Flash MCU | Microchip
PIC24F08KL401-E/SO

PIC24F08KL401-E/SO - 16-bit 32MHz 8KB Flash MCU | Microchip

The Microchip Technology PIC24F08KL401-E/SO is a 16-bit PIC® XLP™ 24F microcontroller featuring 8KB Flash program memory, 1KB RAM, and 512B EEPROM in a 20-pin SOIC package. It operates at up to 32MHz from a 1.8V to 3.6V supply, integrating a 12-bit 10-channel ADC, multiple timers, MSSP (I2C/SPI), CCP/ECCP, comparators, PWM, and nanoWatt XLP™ extreme low-power technology for battery-driven designs. An MCU (Microcontroller Unit) is a single-chip computer containing a CPU core, non-volatile program memory, volatile data memory, and configurable peripheral IP. Within the broader taxonomy, the PIC24F family sits between 8-bit PIC18/AVR MCUs and 32-bit ARM Cortex-M parts, offering 16-bit instruction efficiency at low cost. The KLx family specifically targets picoPower / nanoWatt XLP applications, extending the line of PIC18 peripherals (MSSP, CCP/ECCP) onto the 16-bit core for code-compatible migration. Key features include 8KB self-programmable Flash (2.75K x 24 instruction words), 1KB SRAM, 512B EEPROM, 12-bit ADC with up to 10 channels, dual comparators with selectable reference, three 16-bit timers, a 16-bit PWM, an RTCC, and full-speed USB-free serial peripherals. Brown-out Reset (BOR), High/Low-Voltage Detect (HLVD), Power-on Reset (POR), and Windowed Watchdog Timer (WDT) are integrated for automotive-grade reliability. The -E suffix denotes the -40C to +125C extended operating temperature range for industrial use. Architecturally, the device uses a modified Harvard bus with separate program and data paths, a 16-bit native datapath, and hardware multiply/divide. nanoWatt XLP technology enables deep sleep currents below 1 µA (typical), making the part suited for always-on battery applications. The 20-SOIC (wide-body) footprint eases hand-soldering and probe-friendly bench development. Typical applications include low-cost industrial sensor nodes, battery-powered instrumentation, consumer appliance controllers, LED lighting controllers, and portable medical accessories. Designers migrating from PIC18F to 16-bit PIC24F benefit from shared peripheral libraries and pin-compatible footprints within the KLx family. Design consideration: at 32MHz core from 3.3V, decoupling must include 100nF + 10µF bulk near VDD/AVDD pins; ensure MCLR has proper pull-up for BOR-correct startup. The extended temperature grade -E supports industrial but is not AEC-Q100 qualified - select PIC24F automotive parts for vehicle applications. This page synthesizes distributor pricing, 20-SOIC drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PIC24F08KL401-E/SS - 16-bit MCU 8KB Flash 32MHz SSOP-20
PIC24F08KL401-E/SS

PIC24F08KL401-E/SS - 16-bit MCU 8KB Flash 32MHz SSOP-20

The Microchip Technology PIC24F08KL401-E/SS is a 16-bit Flash microcontroller based on the nanoWatt XLP eXtreme Low Power PIC24F core, delivering 32 MHz / 16 MIPS performance with 8 KB Flash, 1 KB RAM and 512 bytes of EEPROM in a 20-pin SSOP (5.30 mm) package. The part belongs to the PIC24F KL family of low-cost, low-power general-purpose microcontrollers and is offered in the -E (Extended) -40C to +125C temperature grade. A 16-bit microcontroller (MCU) is a single-chip computer that combines a 16-bit CPU core, program memory (Flash), data memory (SRAM), non-volatile EEPROM, and a rich set of on-chip peripherals. Within the broader semiconductor taxonomy, the PIC24F KL family sits between 8-bit PIC MCUs and 32-bit PIC32 devices, offering higher code density and faster arithmetic than 8-bit parts while retaining the ease-of-migration and PIC18-compatible peripherals (MSSP, CCP/ECCP) that simplify the transition from legacy designs. Key features of the PIC24F08KL401 include 12 channels of 10-bit ADC, three 16-bit timers, an MSSP supporting both I2C and SPI, an Enhanced CCP module, a 5-bit DAC reference, two analog comparators, and the nanoWatt XLP ultra-low-power sleep modes that allow deep-sleep currents below 1 A. The 1.8 V to 3.6 V supply range and integrated CTMU make the device suitable for capacitive touch and battery-powered applications. Architecturally, the part uses a modified Harvard bus with a 16-bit data path and 24-bit instruction word, achieving 16 MIPS at 32 MHz. Peripheral pin select is limited compared with larger PIC24F devices, but the PIC18-compatible peripheral set keeps the footprint familiar for engineers migrating from PIC16F/PIC18F designs. Typical applications include consumer remote controls, low-cost sensor nodes, battery-powered IoT endpoints, LED lighting controllers, capacitive touch user interfaces, home appliances, and white goods. The KL family is purpose-built for cost-sensitive designs that need 16-bit performance without the bill of materials cost of larger PIC24F or PIC32 devices. When designing with the PIC24F08KL401, plan oscillator start-up timing and verify minimum VDD rise rates for reliable Flash programming; bulk-decouple VDD with a 100 nF ceramic plus a 4.7 uF bulk cap placed within 3 mm of the supply pin. Use MPLAB X IDE with the XC16 compiler for software development, and refer to the device family data sheet for parametric curves and migration notes. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC24F08KL/KA family, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PIC24F08KL401-I/MQ - 16-Bit 32MHz XLP MCU | Microchip
PIC24F08KL401-I/MQ

PIC24F08KL401-I/MQ - 16-Bit 32MHz XLP MCU | Microchip

The Microchip Technology PIC24F08KL401-I/MQ is a 16-bit PIC24F microcontroller with a 32 MHz operating frequency, 8 KB of program Flash memory, 1 KB of RAM, and a 20-pin VQFN 5 x 5 mm package. It is designed for cost-sensitive embedded applications that require low-power operation, mixed-signal measurement, serial connectivity, and programmable control peripherals. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The PIC24F family is based on a 16-bit architecture and belongs to the broader embedded-controller and power-management ecosystem. The KL401 device combines nanoWatt XLP low-power features with peripherals familiar from the PIC18 ecosystem, including MSSP communication and CCP/ECCP control capabilities. The most important selection criteria are its 32 MHz maximum frequency, 8 KB Flash program memory, 1 KB data RAM, 10-bit ADC, and 20-pin VQFN package. The 512-byte on-chip data memory identified by the distributor listing provides additional nonvolatile storage. These resources suit compact control systems that need periodic sensing, actuator control, and serial communications without requiring a larger external-memory interface. The 16-bit architecture provides a practical balance between processing capability, code efficiency, and embedded cost. MSSP hardware supports I2C or SPI-oriented peripheral integration, while CCP and ECCP modules support timing and pulse-control tasks. The 10-bit ADC enables analog measurement for industrial controls, consumer products, and compact sensing nodes. Exact conversion rates, timer resources, voltage limits, and current consumption require confirmation in the manufacturer datasheet. Typical uses include low-cost sensor nodes, temperature controllers, compact motor-control systems, battery-operated instruments, and embedded communication modules. A design can use the ADC for analog inputs, MSSP for external sensors or displays, and CCP/ECCP for motor, switch, or waveform-control functions. The 5 x 5 mm VQFN also supports space-constrained products when careful PCB layout and exposed-pad thermal management are applied. When designing a board, verify every VQFN-20 land pattern and pin function against the current Microchip documentation. Place the decoupling capacitor close to the supply pins and preserve the manufacturer’s recommended layout for the exposed pad. The -40C to +85C industrial temperature grade and exact operating voltage limits should be confirmed before releasing production hardware. This product page combines the verified Microchip product information with distributor specifications, package identification, application guidance, and strict drop-in replacement analysis. It distinguishes confirmed drop-in options from related devices that require different packages or firmware, helping engineers make a defensible sourcing and design decision.

RFQ Contact
PIC24F08KL401-I/P - 16-bit 32MHz 8KB Flash MCU | Microchip DIP-20
PIC24F08KL401-I/P

PIC24F08KL401-I/P - 16-bit 32MHz 8KB Flash MCU | Microchip DIP-20

The Microchip Technology PIC24F08KL401-I/P is a 16-bit, 32 MHz flash microcontroller with 8 KB program memory, 1 KB SRAM, and a 10-bit ADC, housed in a 20-pin PDIP (DIP-20) package. It belongs to the PIC24F KL4 family and integrates nanoWatt XLP eXtreme Low-Power technology, peripheral select, and the same peripheral set as the PIC18 architecture for flexible migration from 8-bit designs. The part is specified for the industrial temperature range (-40C to +85C) and operates from 1.8 V to 3.6 V. A PIC microcontroller (MCU) is a compact programmable processor that integrates CPU, Flash program memory, SRAM data memory, and peripherals such as timers, ADCs, and communication interfaces into a single silicon die. Within the broader taxonomy, PIC24F devices are 16-bit modified Harvard microcontrollers that sit between 8-bit PIC18 parts and 32-bit PIC32MM devices, and they belong to the wider class of embedded microcontrollers, semiconductors, and integrated circuits used for real-time control. The KL4 sub-family adds dedicated low-power peripherals (RTCC, deep sleep, ultra-low-power wake-up) to support battery-powered designs. Key features of the PIC24F08KL401 include: 8 KB self-programmable flash with program flash visibility, 1 KB SRAM, 512 bytes of EEPROM-like data EEPROM emulation, a 10-bit A/D converter with up to 12 channels, an analog comparator, a Charge Time Measurement Unit (CTMU), and an RTCC. Communication peripherals include MSSP supporting both I2C and SPI, plus a UART with LIN support and IrDA. Capture/Compare/PWM modules include CCP and Enhanced CCP (ECCP) for motor-control PWM. The KL4 family also features Peripheral Pin Select (PPS) for flexible signal routing. Typical applications include cost-sensitive consumer electronics, low-power battery-powered sensor nodes, home appliances and white goods, LED lighting controllers, small motor-control subsystems, and industrial control boards that require 16-bit performance at 8-bit cost. Designers migrating from PIC18F benefit from code and peripheral compatibility while gaining 16-bit arithmetic and DSP-friendly instruction set features. The 32 MHz operation delivers up to 16 MIPS, sufficient for simple closed-loop control and signal processing. When designing with the PIC24F08KL401-I/P, ensure the chosen debug tool supports the device ID (such as PICkit 3/4, MPLAB ICD 4, or MPLAB Snap). Configure unused pins as digital outputs and disable unused peripherals in firmware to achieve nanoWatt XLP sleep currents in the sub-microamp range. This page synthesizes distributor pricing, drop-in package alternatives, and design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC24F08KL401-I/SO - 16-Bit 32MHz XLP MCU | Microchip
PIC24F08KL401-I/SO

PIC24F08KL401-I/SO - 16-Bit 32MHz XLP MCU | Microchip

The Microchip Technology PIC24F08KL401-I/SO is a 16-bit PIC24F microcontroller with a 32 MHz clock, 8 KB of Flash program memory, 1 KB of RAM, and a 20-pin SOIC package. It is designed for cost-sensitive embedded products requiring efficient control, low-power operation, and flexible serial peripherals. The industrial-temperature suffix and compact package make it suitable for industrial instrumentation, consumer devices, portable products, medical equipment, and embedded control systems. What is a PIC24F microcontroller? A PIC24F is a 16-bit RISC flash microcontroller in Microchip's embedded semiconductor product hierarchy. It combines general-purpose control, on-chip memory, interrupt handling, timers, communication peripherals, and analog conversion in one integrated circuit. The KL family emphasizes nanoWatt XLP technology, allowing the CPU, Flash memory, SRAM, and selected peripherals to operate in low-power modes when the application does not require continuous operation. The PIC24F08KL401-I/SO provides 8 KB of Flash memory, 1 KB of SRAM, 17 I/O ports, a 10-bit ADC, and communication resources including MSSP support for I2C or SPI and CCP/ECCP peripherals. These features support sensor acquisition, actuator control, display interfaces, and low-power embedded products. Its 3.0 V to 3.6 V operating supply range is suitable for conventional 3.3 V industrial and consumer electronic systems. The 16-bit architecture offers more arithmetic and addressing capability than an 8-bit MCU while retaining the cost and simplicity associated with Microchip's PIC ecosystem. A 32 MHz operating clock provides deterministic control-loop capability, and the peripheral set allows designers to minimize external discrete components. The MSSP module also consolidates serial-interface functions that would otherwise require separate interface devices. Typical applications include portable media players, GPS accessories, cell-phone accessories, electronic toys, portable sports equipment, disposable medical testers, dispensers, inhalers, safety systems, small industrial controllers, and low-cost sensor nodes. The manufacturer identifies cost-sensitive consumer and medical products as important application areas for the KL family. PCB implementation requires the exact 20-pin SOIC footprint and pin assignments published by Microchip. Designers should confirm the device's ADC channels, I/O functions, power pins, and programming connections against the manufacturer datasheet rather than inferring them from the generic PIC24F family. Decoupling, programming access, and unused-pin handling should follow the relevant Microchip guidance. This product page combines the verified manufacturer and distributor identity, package information, memory configuration, low-power feature set, commercially relevant sourcing details, and engineering guidance. It also separates confirmed drop-in alternatives from package mismatches so engineers can assess replacement risk without redesigning a board unnecessarily.

RFQ Contact
PIC24F08KL401-I/SS - 8KB Flash 16-bit MCU, 32MHz | Microchip
PIC24F08KL401-I/SS

PIC24F08KL401-I/SS - 8KB Flash 16-bit MCU, 32MHz | Microchip

The Microchip PIC24F08KL401-I/SS is a cost-effective 16-bit Flash microcontroller from the PIC24F XLP family featuring nanoWatt XLP technology for eXtreme Low Power consumption, housed in a 20-pin SSOP (5.30 mm body width) package. It integrates 8 KB of self-programmable Flash program memory (2.75 K x 24), 1 KB SRAM, and 16-byte data EEPROM, while operating at up to 32 MHz MIPS performance from a 1.8 V to 3.6 V supply. Peripherals include a 10-bit ADC with up to 12 channels, MSSP (I2C/SPI), two UART modules, CCP/ECCP, and up to 17 I/O pins with interrupt-on-change capability. The -I suffix indicates the -40C to +85C industrial operating temperature grade. A microcontroller (MCU) is an integrated computer-on-a-chip containing a processor core, program and data memory, and configurable peripherals such as ADCs, timers, and communication interfaces. Within the embedded hierarchy, MCUs sit below microprocessors (which require external memory) and above discrete logic; the 16-bit class offers a balance between 8-bit simplicity and 32-bit performance. The PIC24F family specifically targets ultra-low-power applications through nanoWatt XLP technology, which provides sleep currents in the nanoamp range and multiple power-saving modes, making it well-suited for battery-powered products where standby drain dominates battery life. Key features include eXtreme Low Power (XLP) technology, a 17-channel 10-bit ADC with internal bandgap reference, two analog comparators, a 5-bit DAC, and an 8-bit Parallel Master Port on selected variants. The device includes a 16-bit Timer, three 16-bit Timer/Counters, and a Real-Time Clock Calendar (RTCC) module. The integrated peripherals echo PIC18 simplicity to ease migration from older 8-bit designs. The PIC24F08KL401 is built on a Harvard architecture with a 16-bit modified RISC CPU using a 24-bit instruction word. Its deterministic interrupt latency, byte-addressable peripheral registers, and rich peripheral set make it appropriate for cost-sensitive real-time control without sacrificing code density. Brown-out Reset, Watchdog Timer, and Power-on Reset are integrated for system robustness. Typical applications include IoT sensor endpoints, battery-powered sensor nodes, low-power remote controls, appliance user interfaces, and small consumer electronics. Its wide operating voltage range suits 2x AA / coin-cell powered designs where efficiency across the discharge curve is critical. When designing with this MCU, plan the oscillator and decoupling network first; place a 0.1uF decoupling capacitor close to VDD with a bulk 1uF on the same rail. Note that the -I grade limits junction temperatures to -40C to +85C ambient; the -E grade extends this to +125C for harsher environments. This page synthesizes distributor pricing, drop-in SSOP-20 alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC24F08KL401T-I/SO - 16-bit 32MHz MCU, 8KB Flash, 20-SOIC | Microchip
PIC24F08KL401T-I/SO

PIC24F08KL401T-I/SO - 16-bit 32MHz MCU, 8KB Flash, 20-SOIC | Microchip

The Microchip Technology PIC24F08KL401T-I/SO is a 16-bit microcontroller from the PIC24F KL401 family, delivering 32 MIPS performance at 32 MHz while consuming nanoWatt XLP eXtreme Low Power for battery-friendly designs. The device integrates 8 KB of Flash program memory (2.75K x 24 words), 1 KB of SRAM, and a 10-bit ADC, all housed in a 20-pin SOIC (7.50 mm body width) package. It operates from a 1.8V to 3.6V supply with 17 available I/O pins for mixed-signal interfacing. A 16-bit microcontroller (MCU) is an embedded processor that executes instructions on 16-bit data paths in a single cycle, delivering roughly 2x the throughput of an 8-bit MCU while remaining power-efficient for cost-sensitive applications. The PIC24F family occupies the middle tier of Microchip's portfolio, sitting between the PIC18 (8-bit) and dsPIC33 (DSP-enhanced 16-bit) families and inheriting familiar PIC18 peripherals such as MSSP for I2C/SPI and CCP/ECCP for PWM, which simplifies migration from older 8-bit designs. Key features of the PIC24F08KL401T-I/SO include the nanoWatt XLP technology suite (Deep Sleep, Doze, Idle modes), 17 GPIO, 10-bit ADC with internal reference support, MSSP (I2C/SPI), a configurable ECCP/PWM module, and a 32 kHz RTCC timer. The part is AEC-Q100 friendly with an industrial operating range of -40 C to +85 C and supports in-circuit serial programming (ICSP) via the MPLAB Snap or PICkit 4 debuggers. Architecture-wise, the PIC24F08KL401T-I/SO uses a modified Harvard core with a 24-bit instruction word and 16-bit data path. This dual-bus architecture allows simultaneous fetch and access, while XLP modes drop quiescent current into the microamp range, suiting always-on sensors. Typical applications include low-cost IoT sensor nodes, battery-powered consumer devices, USB-less human-interface controllers, small industrial control boards, and HVAC monitoring front ends. The wide 1.8V-3.6V range simplifies designs powered by 2x AA cells or single-cell Li-ion. Design consideration: route an external 32.768 kHz crystal only if you need a real-time clock; otherwise use the internal LF oscillator to save two GPIOs and BOM cost. The MSSP, ADC, and I/O map must be checked against your PCB layout because some analog channels share pins with digital functions. This page synthesizes distributor pricing, drop-in SOIC-20 alternatives from the PIC24F KL/ KA family, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC24F08KL402-E/ML - 16-bit 32MHz MCU, 8KB Flash, 28-QFN | Microchip
PIC24F08KL402-E/ML

PIC24F08KL402-E/ML - 16-bit 32MHz MCU, 8KB Flash, 28-QFN | Microchip

The Microchip PIC24F08KL402-E/ML is a 16-bit PIC24F microcontroller with 8KB Flash, 1KB RAM, and 512B EEPROM in a 28-pin QFN (6x6 mm) package, operating at up to 32 MHz (16 MIPS). Designed around the nanoWatt XLP eXtreme Low Power technology platform, it targets cost-sensitive, low-power embedded applications across consumer, industrial, and IoT segments. What is a 16-bit microcontroller? A microcontroller (MCU) is a single-chip computer integrating a CPU, memory (Flash for program code, RAM for data, EEPROM for non-volatile storage), and peripherals on one die. A 16-bit MCU like the PIC24F processes data 16 bits at a time, sitting between 8-bit MCUs (PIC10/12/16/18) and 32-bit MCUs (PIC32, ARM Cortex-M) in both price and performance. The PIC24F family is optimized for low power consumption while delivering computational headroom above 8-bit parts. Key features of the PIC24F08KL402 include nanoWatt XLP technology for sleep currents in the nanoampere range, 12-channel 10-bit ADC for sensor acquisition, dual op-amps and comparators for analog signal conditioning, plus MSSP (I2C/SPI) and CCP/ECCP peripherals borrowed from the PIC18 family to ease migration. The 28-QFN package with exposed thermal pad offers a compact 6x6 mm footprint suitable for space-constrained designs. Technically, the part runs from a wide 1.8V to 3.6V supply, supports up to 16 MIPS throughput, and provides multiple low-power modes (Sleep, Deep Sleep, Retention) controlled via the on-chip RTCC and deep-draw hardware. The peripheral set is intentionally minimalist but flexible, allowing developers to scale functionality without jumping to larger flash densities. Typical applications include battery-powered sensor nodes, wearable health monitors, consumer remote controls, home automation endpoints, and low-cost industrial control front-ends. Its combination of PIC18-compatible peripherals with PIC24-class CPU throughput makes it well suited as a migration target from 8-bit designs that have outgrown their original MCU. When designing with this part, plan pin assignments carefully since the 28-QFN variant has fewer I/O pins than 28-SOIC/SPDIP equivalents - verify your I/O budget against the datasheet pin table before committing to the PCB layout.

RFQ Contact
PIC24F08KL402-E/SO - 16-bit 32MHz 8KB Flash MCU | Microchip
PIC24F08KL402-E/SO

PIC24F08KL402-E/SO - 16-bit 32MHz 8KB Flash MCU | Microchip

The Microchip Technology PIC24F08KL402-E/SO is a cost-optimized 16-bit PIC microcontroller featuring the eXtreme Low Power (XLP) nanoWatt technology, 8KB of Flash program memory, 1KB of SRAM, and 512B of EEPROM in a 28-pin SOIC package. It integrates a 32MHz PIC24F core with peripheral blocks inherited from the PIC18 family (MSSP for I2C/SPI and CCP/ECCP), enabling easy migration from legacy 8-bit designs. Operating voltage spans 1.8V to 3.6V with AEC-Q100 automotive qualification per the manufacturer's extended temperature (-40C to +125C) marking. A 16-bit microcontroller is a single-chip computer that fetches, decodes, and executes instructions with a 16-bit wide datapath, offering a meaningful step up in code density, arithmetic precision, and peripheral throughput over traditional 8-bit MCUs while remaining lower cost and lower power than 32-bit Cortex-M parts. PIC24F devices sit in Microchip's mid-range 16-bit portfolio, positioned between the legacy PIC18 and the dsPIC/PIC32 lines, and target cost-sensitive applications that benefit from a real C-programmable core with on-chip analog and communication peripherals. Key features of the PIC24F08KL402 include up to 32 MIPS core throughput at 32MHz, configurable 8-channel 10-bit ADC, two analog comparators, two UART/SPI/I2C-capable MSSP ports, up to 25 mA source/sink I/O, and nanoWatt XLP sleep currents below 1 uA in deep-sleep retention mode. The 28-SOIC package is footprint-compatible with the PIC24F08KL302 and PIC24F08KL201 families, allowing board reuse across the KL series. The device uses a Harvard architecture with separate program and data buses, a hardware multiply/divide unit, and a 16-element register file. Code and data are protected by separate Flash and Memory spaces for security, and the integrated ICSP (In-Circuit Serial Programming) interface allows in-field firmware updates without bootloader overhead. Typical applications include cost-sensitive 16-bit embedded controls such as home appliances, sensor signal conditioning, low-power IoT sensor nodes, HVAC actuator controllers, and AEC-Q100 automotive body modules. The combination of nanoWatt XLP, MSSP, and 10-bit ADC enables direct battery-powered operation with minimal external components. Design tip: leverage the MSSP peripheral in either SPI or I2C mode to offload bit-banged communication from the CPU, freeing bandwidth for the 10-bit ADC scan loop. For noise immunity in automotive environments, place the VCAP decoupling capacitor within 3mm of the VCAP pin and keep ADC traces short and guarded. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the KL/KA families, and practical design notes not found on the manufacturer product page.

RFQ Contact
PIC24F08KL402-E/SP - 16-bit XLP MCU 8KB Flash 28-SPDIP | Microchip
PIC24F08KL402-E/SP

PIC24F08KL402-E/SP - 16-bit XLP MCU 8KB Flash 28-SPDIP | Microchip

The Microchip Technology PIC24F08KL402-E/SP is a 16-bit PIC microcontroller with nanoWatt XLP eXtreme Low Power technology, featuring 8KB of Flash program memory (2.75K x 24 instruction words), 1KB RAM, and 512 bytes of EEPROM in a 28-pin SPDIP through-hole package. It runs at up to 32 MHz delivering 16 MIPS, integrates a 12-channel 10-bit ADC, and provides flexible peripherals including MSSP (I2C/SPI), CCP/ECCP, and multiple timers. A 16-bit microcontroller (MCU) is an integrated circuit containing a CPU, program memory, RAM, and peripherals on a single die. The PIC24F family uses a modified Harvard architecture with 16-bit wide instructions and data paths, offering a balance between the simplicity of 8-bit PIC MCUs and the performance of 32-bit devices. Within the broader taxonomy: microcontroller -> 16-bit MCU -> PIC24F family -> PIC24F08KLx series -> low-power (XLP) variant. This part targets cost-sensitive applications where 16-bit performance is needed without 32-bit complexity. Key features include extreme low-power operation with nanoWatt XLP sleep currents, a 32 MHz internal oscillator, 23 digital I/O pins with interrupt-on-change capability, and 12 channels of 10-bit analog-to-digital conversion at 500 ksps. The device operates from 1.8V to 3.6V with on-chip voltage regulation, supports in-circuit serial programming (ICSP) and in-circuit debugging (ICD), and offers multiple communication interfaces including I2C, SPI, and UART. The PIC24F08KL402-E/SP uses a 16-bit RISC-style core with single-cycle multiply and hardware divide, providing deterministic interrupt latency for real-time control. Its nanoWatt XLP technology enables sleep currents below 1 uA, making it suitable for battery-powered sensor nodes, wearable electronics, and remote monitoring equipment where idle power dominates total energy consumption. Typical applications include IoT sensor nodes, low-power wireless devices, portable medical instruments, consumer electronics with battery backup, industrial sensor interfaces, and home automation controllers. The wide -40C to +125C operating range also supports industrial and outdoor deployments requiring extended temperature tolerance. When designing with this part, allocate careful attention to the ICSP programming header placement to avoid interference with debug access. The MSSP peripheral requires careful I2C pull-up resistor sizing and timing-budget analysis for multi-master or long-bus configurations. This page synthesizes verified distributor pricing, drop-in alternatives from the same KL family, and practical design notes that complement the manufacturer datasheet to help engineers select and qualify this part with confidence.

RFQ Contact
PIC24F08KL402-E/SS - 32MHz 16-bit MCU | Microchip Technology
PIC24F08KL402-E/SS

PIC24F08KL402-E/SS - 32MHz 16-bit MCU | Microchip Technology

The Microchip Technology PIC24F08KL402-E/SS is a 16-bit PIC24F microcontroller featuring nanoWatt XLP low-power technology, a 32 MHz operating frequency, 8 KB Flash memory, 1 KB RAM, 512 bytes of EEPROM, and a 28-pin SSOP package. It combines a compact general-purpose control architecture with nanoWatt XLP, 10-bit ADC, comparators, CCP/ECCP, and MSSP peripherals for I2C and SPI communication. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, and peripherals into one package. The PIC24F08KL402 belongs to the PIC24F family of 16-bit Flash microcontrollers, combining a general-purpose embedded-control hierarchy with low-power design features. Its 28-SSOP package is intended for compact, cost-sensitive embedded systems where board area, flash memory, analog measurement, and serial connectivity must be balanced. The PIC24F08KL402 provides 8 KB of Flash program memory organized as 2.75K x 24 words, 1 KB of RAM, and 512 bytes of EEPROM according to distributor product information. The integrated 10-bit ADC supports analog measurement tasks, while comparators provide hardware threshold detection. CCP and ECCP peripherals add capture, compare, and PWM capabilities for timing, motor-control, and signal-generation functions. Its MSSP peripheral supports I2C and SPI, making the device appropriate for sensors, display drivers, memory devices, and other serial peripherals. The 32 MHz maximum operating frequency provides additional computation and timing headroom compared with slower general-purpose microcontrollers, while the small 8 KB Flash footprint keeps the device economical for compact control products. Typical applications include low-cost sensor nodes, industrial monitoring equipment, small motor-control systems, consumer appliances, and embedded control boards requiring I2C or SPI connectivity. The PIC24F08KL402-E/SS suffix identifies the SSOP package and E temperature-grade ordering option, while the -I/SS ordering variant provides a separate industrial temperature-grade option. Designers should verify the complete pin allocation, operating-voltage limits, ADC performance, and peripheral electrical limits against the manufacturer datasheet before layout. The 28-SSOP footprint requires careful spacing between adjacent pins, and the 8 KB Flash limit should be checked against application code size, bootloader requirements, and library overhead. Commercial availability and pricing should also be confirmed at the time of purchase because the supplied distributor search results establish product listings but do not provide a stable price matrix. This page combines the verified manufacturer and distributor facts with practical application guidance, package considerations, and an honest assessment of drop-in replacement options. It is intended to help engineers compare the PIC24F08KL402-E/SS with related 28-SSOP configurations before committing a PCB design.

RFQ Contact
PIC24F08KL402-I/ML - 16-bit MCU, 8KB Flash, 32MHz | Microchip
PIC24F08KL402-I/ML

PIC24F08KL402-I/ML - 16-bit MCU, 8KB Flash, 32MHz | Microchip

The Microchip Technology PIC24F08KL402-I/ML is a 16-bit Flash microcontroller from the PIC24F KL402 family, featuring nanoWatt XLP technology for eXtreme Low Power consumption. It integrates 8 KB of Flash program memory, 1 KB of SRAM, and a 512-byte data EEPROM, runs at 32 MHz CPU clock speed, and operates from a 3.0 V to 3.6 V supply. Housed in a 28-pin VQFN (6x6 mm) package with exposed thermal pad (ML suffix), this device is qualified for the industrial temperature range (-40C to +85C) and targets cost-sensitive 16-bit embedded designs that previously used PIC18 architectures. A microcontroller (MCU) is a single-chip computer containing a processor core, program and data memory, and integrated peripherals such as timers, communication interfaces and analog blocks. The PIC24F family sits at the low-power, low-cost end of Microchip's 16-bit MCU portfolio, sitting below dsPIC and PIC24EP parts in performance hierarchy. Compared with 8-bit PIC MCUs, PIC24F devices offer 16-bit data paths, higher MIPS per MHz and richer peripherals, while keeping the same MPLAB X IDE and XC16 toolchain compatibility. The KL402 sub-family further adds nanoWatt XLP sleep modes that drop current into the nanoampere range for battery-powered designs. Key features include 17 general-purpose I/O pins, a 10-bit ADC with multiple channels, two UART modules, MSSP (I2C/SPI), CCP/ECCP capture/compare/PWM peripherals, and 5 timer modules. The 10-bit ADC supports up to 12 input channels with automatic sampling. Real-time clock, hardware CRC and a charge time measurement unit (CTMU) for capacitive touch round out the on-chip peripheral set. The device also integrates a 32 kHz low-power oscillator and supports multiple low-power sleep modes including Sleep, Idle and Doze. The PIC24F08KL402 uses a modified Harvard architecture with a 16-bit datapath and 24-bit instruction word, achieving 16 MIPS at 32 MHz. The CIP (Core Independent Peripherals) concept allows peripherals to operate without CPU intervention, reducing firmware complexity and active-time power. The CTMU enables mTouch capacitive touch sensing without an external charge pump, while the MSSP peripheral supports both I2C and SPI masters/slaves, simplifying sensor and display integration. Typical applications include low-power IoT sensor nodes, consumer white goods, home automation, battery-powered handheld instruments, LED lighting control, and cost-sensitive industrial controls. The combination of XLP sleep currents under 100 nA and the 32 MHz performance makes it well suited for products that spend most of their life in sleep but wake periodically to perform measurement or communication tasks. When designing with this part, plan the layout to keep the exposed thermal pad (EP) soldered to the ground plane for mechanical strength and thermal relief. Use MPLAB X IDE with the XC16 compiler for firmware development, and consider the free MPLAB Code Configurator (MCC) plug-in to generate peripheral init code. Decouple VDD/VSS with a 100 nF ceramic capacitor close to each power pin pair as called out in the datasheet. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet, giving engineers a single reference for part selection, sourcing and PCB layout.

RFQ Contact
PIC24F08KL402-I/MQ - 32MHz 16-Bit MCU | Microchip Technology
PIC24F08KL402-I/MQ

PIC24F08KL402-I/MQ - 32MHz 16-Bit MCU | Microchip Technology

The Microchip Technology PIC24F08KL402-I/MQ is a 16-bit PIC24F microcontroller with a 32 MHz maximum clock, 8 KB of Flash program memory, 1 KB of SRAM, 512 bytes of EEPROM, and a 10-bit ADC in a 28-QFN 5x5 mm package. The -I/MQ ordering identifies an industrial-temperature 28-QFN configuration, while the PIC24F08KL402 family is positioned for cost-sensitive embedded control and low-power applications. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The PIC24F08KL402 belongs to the PIC24F family of 16-bit Flash microcontrollers, which sits within the broader embedded-controller and semiconductor hierarchy. Its nanoWatt XLP technology supports low-power operating modes intended for battery-powered or intermittently powered products where reducing energy consumption is important. Key features include 8 KB of Flash for firmware storage, 1 KB of SRAM for working data, 512 bytes of EEPROM for nonvolatile parameters, 17 I/O ports, and a 10-bit ADC. The MSSP peripheral supports I2C or SPI communication, while the CCP and ECCP modules add capture, compare, and PWM capabilities. These resources allow the device to consolidate functions that might otherwise require separate interface and timing components. The device operates from 3 V to 3.6 V and can run at up to 32 MHz. Its 16-bit architecture provides a practical balance between computational capacity, memory efficiency, and implementation cost for general-purpose control. The -I/MQ package combines a compact 5x5 mm QFN footprint with 17 available I/O pins, making it appropriate for space-constrained control boards that require several digital interfaces and analog measurement channels. Typical applications include industrial sensor nodes, compact motor-control modules, cost-sensitive data acquisition units, low-power environmental monitors, and small appliance controllers. An I2C bus can connect the MCU to a sensor or display, SPI can support higher-speed peripherals, and the ADC can read analog inputs. For designs requiring additional memory, pin count, or specialized peripherals, a larger member of the PIC24F family may be a better fit. Designers should verify the complete QFN-28 pin assignment, exposed-pad connection, decoupling requirements, and peripheral multiplexing against the manufacturer documentation before layout. The 3 V to 3.6 V supply range also requires regulators and signal levels that remain compatible with 3.3 V peripherals. Software configuration should avoid assuming that every peripheral can operate simultaneously because pin multiplexing and shared resources can constrain valid combinations. This page consolidates the verified device specifications, sourcing information, package details, lifecycle status, and honest replacement analysis in one place. It also distinguishes a genuine same-package electrical option from variants that cannot be treated as drop-in replacements, helping engineers make PCB-compatible design decisions without relying on assumptions.

RFQ Contact
PIC24F08KL402-I/SO - 32MHz 16-Bit MCU | Microchip Technology
PIC24F08KL402-I/SO

PIC24F08KL402-I/SO - 32MHz 16-Bit MCU | Microchip Technology

The Microchip Technology PIC24F08KL402-I/SO is a cost-sensitive 16-bit PIC24F flash microcontroller with a 32 MHz clock, 8 KB program flash, 1 KB SRAM, 512 bytes of EEPROM, and a 28-pin SOIC package. Its operating supply range is 3 V to 3.6 V, while the industrial-temperature suffix identifies the part for industrial operating conditions. The integrated 10-bit ADC, 17 I/O ports, MSSP interface supporting I2C or SPI, and CCP/ECCP peripherals make the device suitable for compact embedded-control systems that require more capability than an 8-bit MCU without adopting a higher-cost platform. A microcontroller is a programmable semiconductor that combines a processor core, nonvolatile program memory, working memory, I/O, and peripherals on one integrated circuit. The PIC24F08KL402 belongs to the PIC24F family of 16-bit flash microcontrollers and sits within the broader embedded-processing and embedded-control hierarchy. Its 16-bit architecture provides a larger processing register and instruction set than an 8-bit MCU, while the integrated nanoWatt XLP design emphasizes reduced current consumption during idle, sleep, and other low-activity operating modes. The verified feature set includes 8 KB of flash organized as 2.75K by 24 words, 1 KB of SRAM, and 512 bytes of EEPROM. A 10-bit ADC supports analog measurement, while the 17 available I/O ports allow digital inputs, outputs, and communications links to be implemented in a compact design. The MSSP peripheral supports I2C or SPI communication, and the CCP/ECCP modules provide capture, compare, and PWM functions useful for motor control, timing, signal generation, and industrial automation. The PIC24F08KL402-I/SO combines conventional 16-bit processing with low-power design and familiar PIC peripheral blocks. Its 32 MHz operating frequency provides a practical balance between control-loop responsiveness, general-purpose processing, and power-conscious design. The 28-lead SOIC package also offers a mechanically accessible option for through-hole assembly, programming, inspection, and repair in cost-sensitive industrial products. Typical applications include compact industrial controllers, temperature and process-monitoring instruments, sensor-conditioning nodes, small motor-control boards, keypad interfaces, and communication bridges. In each case, the MCU can execute control logic, acquire analog measurements, drive PWM outputs, and communicate with sensors or peripherals through its integrated interfaces. The 3 V to 3.6 V supply range also allows the device to share a regulated 3.3 V system rail. When designing around this MCU, verify the exact pin assignments and peripheral multiplexing from the manufacturer datasheet before assigning signals. Provide local decoupling close to the supply pins, keep sensitive analog and communications routes away from noisy switching paths, and confirm the required programming and configuration interface. The supplied data does not state the complete pin table, temperature limits, ADC channel count, or programming-tool details, so those values require confirmation from Microchip documentation. This product record combines the verified manufacturer, distributor, and cross-reference information with a practical engineering assessment of the 16-bit core, nanoWatt XLP positioning, analog conversion, communications, and timer resources. It also distinguishes a confirmed same-package suffix alternative from package variants that cannot be treated as true drop-in replacements.

RFQ Contact
PIC24F08KL402-I/SP - 16-bit 32MHz MCU 8KB Flash 28-SPDIP | Microchip
PIC24F08KL402-I/SP

PIC24F08KL402-I/SP - 16-bit 32MHz MCU 8KB Flash 28-SPDIP | Microchip

The Microchip Technology PIC24F08KL402-I/SP is a 16-bit microcontroller from the PIC24F KL family featuring 8 KB of Flash program memory, 1 KB of SRAM, and 512 bytes of EEPROM, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It operates at up to 32 MHz instruction-cycle speed, integrates a 10-bit ADC with up to 12 channels, and runs from a 1.8 V to 3.6 V supply. The /SP suffix denotes the 28-pin SPDIP industrial-temperature package rated from -40 °C to +85 °C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. The PIC24F uses Microchip's 16-bit modified-Harvard architecture with a 16-bit-wide instruction path and a 24-bit-wide instruction word, delivering roughly 2x to 5x the throughput of PIC18 8-bit parts at the same clock while remaining C-friendly. The KL402 sits at the entry level of the KL4 sub-family, designed as a cost-optimized migration path from PIC18 designs thanks to compatible peripherals such as MSSP (I²C/SPI), CCP/ECCP, and the same core register model. Key features of the PIC24F08KL402 include nanoWatt XLP technology for eXtreme Low Power consumption (deep-sleep currents in the nanoamp range), four 16-bit timers, two UART modules, one I²C/SPI MSSP, up to 25 mA source/sink per I/O, and a 10-bit 1.1 Msps ADC. The device supports In-Circuit Serial Programming (ICSP) and In-Circuit Debug (ICD) via two standard pins, enabling field firmware updates and low-cost development. A wide operating range of 1.8 V to 3.6 V allows direct connection to single-cell Li-ion, two-AA, or 3.3 V regulated rails. Architecturally, the KL4 core uses a single-cycle hardware multiply, a 17-bit × 17-bit MAC for DSP-style operations, and a 16-element working register array. The MSSP block reuses the familiar PIC18 SPI/I²C controller, easing code porting. The 10-bit successive-approximation ADC has a dedicated FRC oscillator and supports automatic Channel Scan and Buffer Mode. Internal oscillators are accurate to within ±2 % across temperature, eliminating the need for an external crystal in most designs. Typical applications for the PIC24F08KL402-I/SP include low-power IoT sensor nodes, battery-powered consumer devices, low-cost motor-control loops (small DC and stepper), home appliances, e-metering accessories, USB-to-UART bridges (when paired with an external transceiver), and industrial control user-interface panels. The 28-SPDIP package is especially favored for prototype breadboarding, hobbyist designs, and through-hole production assemblies where socketed replacement or hand rework is required. When designing with this MCU, note that the 28-SPDIP variant exposes 25 general-purpose I/O. For surface-mount or smaller-footprint designs, Microchip offers the same silicon in PIC24F08KL402-I/SS (28-SSOP), PIC24F08KL402-I/SO (28-SOIC), and PIC24F08KL402-I/ML (28-QFN) packages. The 'I' industrial temperature grade is the right choice for -40 °C to +85 °C environments; switch to the 'E' extended grade for -40 °C to +125 °C automotive or industrial high-temperature applications. This page synthesizes distributor pricing, verified drop-in alternatives, and practical engineering design notes not found in the manufacturer datasheet alone, giving procurement and design engineers a faster path to qualification.

RFQ Contact
PIC24F08KL402-I/SS - 32MHz 16-Bit nanoWatt XLP MCU | Microchip Technology
PIC24F08KL402-I/SS

PIC24F08KL402-I/SS - 32MHz 16-Bit nanoWatt XLP MCU | Microchip Technology

The Microchip Technology PIC24F08KL402-I/SS is a 16-bit PIC24 RISC microcontroller with a 32 MHz CPU, 8 KB of Flash program memory, 1 KB of data RAM, and a 28-pin SSOP package. The device also provides 512 bytes of EEPROM, a 10-bit ADC, and nanoWatt XLP technology for low-power operation. It is positioned for cost-sensitive embedded systems that require a compact general-purpose controller with mixed-signal and serial communications support. A PIC24 microcontroller is a general-purpose 16-bit embedded controller within the broader semiconductor and microcontroller hierarchy. Unlike an 8-bit MCU, the PIC24 architecture provides a wider register and data path suited to control loops, protocol handling, and compact sensor-processing tasks. The PIC24F08KL402 combines that core with nanoWatt XLP power-management functions, MSSP support for I2C or SPI, and CCP/ECCP peripherals for flexible timing and capture or compare functions. The verified device data identifies a 32 MHz operating frequency, 8 KB of Flash memory organized as 2.75K by 24 words, and 1 KB of data RAM. Its 10-bit ADC supports embedded analog measurement, while two comparators, six timers, and a watchdog timer broaden the on-chip control resources. MSSP peripherals support I2C and SPI connectivity, and ECCP provides additional control flexibility where the application requires more dedicated capture, compare, or pulse-width resources. The PIC24F08KL402 is a CMOS device that combines power-on reset and brown-out reset protections with low-power design features. Its 512-byte EEPROM gives the firmware a nonvolatile location for calibration values, configuration data, or counters that must survive a power cycle. The industrial-temperature suffix in the ordered MPN identifies the -I/SS ordering code, while the SSOP package provides 28 leads for surface-mount assembly. Typical applications include industrial sensor nodes, compact environmental monitors, motor or actuator controllers, low-power data-acquisition modules, and connected equipment using SPI or I2C peripherals. Its 10-bit ADC supports sensor interfaces, while the timer and CCP resources suit periodic measurement, PWM generation, and timing tasks. The combination of 32 MHz processing and 1 KB of RAM is appropriate for small control loops rather than memory-intensive edge-computing workloads. Designers should verify the exact operating-voltage range, ADC performance, pin multiplexing, and timing limits in the manufacturer datasheet before layout release. Decoupling, programming, and clock considerations should follow the device's recommended hardware guidelines. Because the verified data does not provide a complete pin table, this page does not reconstruct or guess individual pin assignments. This page combines verified distributor specifications, manufacturer product information, and explicitly sourced drop-in references with practical design guidance. It distinguishes confirmed electrical and peripheral data from unavailable details, helping engineers compare the PIC24F08KL402-I/SS without introducing unsupported specifications.

RFQ Contact
PIC24F08KM101-E/P - 16-bit MCU, 8KB Flash, 32MHz | Microchip
PIC24F08KM101-E/P

PIC24F08KM101-E/P - 16-bit MCU, 8KB Flash, 32MHz | Microchip

The Microchip Technology PIC24F08KM101-E/P is a 16-bit PIC XLP 24F microcontroller with 8KB Flash, 1KB RAM, and 512B EEPROM, housed in a 20-pin PDIP package rated for the -40C to +125C industrial temperature range. The device runs at up to 32MHz core clock from a 1.8V-3.6V supply and integrates a 12-bit ADC with up to 16 input channels, dual comparators, configurable logic cells, and CCP/PWM modules. It belongs to the nanoWatt XLP family, which targets extreme low-power applications where active current and sleep current both matter. What is a PIC24F microcontroller? A PIC24F is a 16-bit RISC microcontroller in the Microchip PIC24 family, sitting between the 8-bit PIC16/PIC18 line and the 32-bit PIC32 line in Microchip's portfolio. It uses a modified Harvard architecture with a 16-bit data path, runs most instructions in one cycle, and is aimed at low-power embedded designs that need more headroom than 8-bit parts but not the full performance of a 32-bit core. PIC24F derivatives add Microchip's eXtreme Low Power (XLP) technology with deep-sleep currents below 1 uA, making them common in battery and energy-harvesting designs. The PIC24F08KM101-E/P offers three differentiating features for its class: 8KB self-programmable Flash with configurable write protection, a 12-bit ADC with integrated 1.024V bandgap reference for ratiometric measurements, and MCCP/SCCP timer modules supporting Capture, Compare, and PWM modes. Its nanoWatt XLP idle and sleep modes drop quiescent current into the microamp range, while the integrated op-amp and dual comparators let designers replace several external analog components. Real-Time Clock/Calendar hardware with separate 32kHz oscillator domain is also supported, enabling accurate time-of-day tracking without an external RTC IC. The architecture is built around a 16-bit modified Harvard core with a 3-stage pipeline, single-cycle multiply, and bit-manipulation instructions inherited from the PIC18 instruction set. Peripherals are mapped via a Peripheral Pin Select (PPS) system on PPS-capable pins, which simplifies PCB routing by remapping digital functions to alternate physical pins. The bus matrix routes 16-bit data and 24-bit instructions in parallel, giving deterministic interrupt latency critical for motor and power-control loops. Typical applications for the PIC24F08KM101-E/P include battery-powered sensor nodes, low-cost consumer appliances, industrial control panels, HVAC controllers, and small motor-control boards. Its DIP-20 package and breadboard-friendly form factor also make it a frequent choice for prototyping, hobby projects, and educational platforms. With 12-bit ADC resolution it can read thermistors, photodiodes, and strain gauges without an external signal conditioner. When designing with the PIC24F08KM101-E/P, plan the analog and digital ground topology - the device mixes a 12-bit ADC with switching I/O, and poor grounding will eat into that resolution. Use a ferrite bead or pi-filter on the analog AVdd pin to isolate ADC supply noise from digital Vdd, and add a 100nF ceramic decoupling cap within 5mm of each Vdd pin. The PPS system requires unlocking the IOLOCK register after programming, so account for that in your firmware bring-up sequence. This page synthesizes verified distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PIC24F08KM101-E/SO - 32MHz 8KB 16-Bit MCU | Microchip
PIC24F08KM101-E/SO

PIC24F08KM101-E/SO - 32MHz 8KB 16-Bit MCU | Microchip

The Microchip Technology PIC24F08KM101-E/SO is a 16-bit PIC XLP 24F microcontroller operating up to 32 MHz, with 8 KB of Flash program memory, 1 KB of RAM, and 512 bytes of EEPROM in a 20-pin SOIC package. The -E/SO ordering code identifies the extended-temperature automotive-grade version in the gull-wing package. A PIC XLP microcontroller is a low-power embedded controller combining a 16-bit RISC core, digital peripherals, analog conversion functions, and communications interfaces in one integrated circuit. It belongs to the PIC24F family of 16-bit microcontrollers, where low-power design and a small pin count suit compact control, sensing, and communication products. Principal features include a 32 MHz maximum operating speed, 8 KB of Flash organized as 2.75K × 24 words, 1K × 8 bits of RAM, and 512 × 8 bits of EEPROM. The device supports operation from 1.8 V to 5.5 V and integrates a 12-bit ADC, comparator, and flexible capture, compare, and PWM modules. Communication capabilities include I2C, SPI, UART/USART, IrDA, and LINbus support. The 20-pin architecture concentrates mixed-signal and control resources into a compact package. Its 12-bit ADC supports embedded measurement, while the comparator can perform threshold detection without a separate analog device. The integrated EEPROM provides nonvolatile parameter storage, and the 8 KB Flash region accommodates control firmware and application code within the constraints of a small low-power design. Typical applications include industrial sensor controllers, compact motor and actuator controls, battery-powered instruments, communications modules, LED lighting controllers, and compact consumer appliances. The combination of low pin count, 1.8 V to 5.5 V operating range, and multiple serial interfaces makes the PIC24F08KM101-E/SO appropriate for designs that need flexible embedded control without a high pin-count package. During PCB design, assign analog, power, ground, and programming pins according to the manufacturer pin-description table, and verify the external decoupling and oscillator requirements for the selected configuration. Firmware should also account for the peripheral mix and electrical limits associated with the exact PIC24F KM variant before production release. This page consolidates the device specifications, family-based drop-in alternatives, interface capabilities, and design guidance into one engineering reference for component selection and PCB implementation.

RFQ Contact
PIC24F08KM101-E/SS - 16-bit XLP MCU 8KB Flash 20-SSOP | Microchip
PIC24F08KM101-E/SS

PIC24F08KM101-E/SS - 16-bit XLP MCU 8KB Flash 20-SSOP | Microchip

The Microchip Technology PIC24F08KM101-E/SS is a 16-bit PIC® XLP™ 24F microcontroller featuring 8KB of Flash program memory (2.75K x 24 words), 1KB of RAM and 512 bytes of EEPROM, operating at up to 32MHz from a 1.8V to 5.5V supply. It is housed in a 20-pin SSOP (SS) package and integrates a 12-bit ADC, a 10-bit DAC, comparators, op-amps and configurable logic cells that suit compact analog-front-end designs. A low-power microcontroller (MCU) is a programmable processing device with on-chip memory and peripherals that targets battery- and energy-constrained products. Within the broader taxonomy, the PIC24F08KM101 belongs to the 16-bit MCU family -> microcontroller -> embedded processor -> semiconductor IC category. The "XLP" (eXtreme Low Power) designation indicates nanoWatt technology for sleep currents down to the sub-microamp range, enabling years of operation on a single coin cell. Key features of the PIC24F08KM101 include eXtreme Low Power nanoWatt technology, 12-bit A/D with up to 9 input channels, a 10-bit DAC, three op-amps, two comparators, configurable logic cells, MCCP/SCCP capture/compare/PWM modules, and serial peripherals including I2C, SPI, UART and IrDA. The device runs from 1.8V to 5.5V and supports both 3V and 5V system rails. Architecturally, the PIC24F08KM101 uses a 16-bit modified Harvard core with separate program and data buses, allowing single-cycle instruction fetch with simultaneous data access. The integrated op-amps and comparators reduce external analog component count, while the Configurable Logic Cell (CLC) lets designers implement custom glue-logic functions without discrete gates. Typical applications include portable medical sensors, e-metering and smart energy nodes, capacitive-touch user interfaces, IoT edge sensor hubs, automotive body and sensor nodes (LIN bus), and small industrial control boards where low power, integrated analog, and a compact 20-pin footprint are all required simultaneously. When designing with the PIC24F08KM101, confirm that the chosen ADC reference, op-amp gain settings, and PWM frequency all align with the 32MHz system clock budget. The 20-SSOP package gives a 5.30mm body width, ideal for dense hand-held PCBs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PIC24F08KM101-I/P - 16-bit 32MHz 8KB Flash MCU 20-PDIP | Microchip
PIC24F08KM101-I/P

PIC24F08KM101-I/P - 16-bit 32MHz 8KB Flash MCU 20-PDIP | Microchip

The Microchip Technology PIC24F08KM101-I/P is a 16-bit microcontroller from the PIC24F KM family, featuring 32 MHz CPU speed, 8 KB of Flash program memory, 1 KB of RAM, and packaged in a 20-pin PDIP through-hole form factor. The PIC24F KM family integrates a 12-bit ADC, DAC, and operational amplifiers, and supports both 3V and 5V application rails with operating voltages from 1.8 V to 5.5 V (the PIC24FV suffix variants support 2.0 V to 5.5 V). This low pin-count device is engineered for low-cost, low-power embedded applications and is built on the nanoWatt eXtreme Low Power (XLP) platform, which delivers deep-sleep currents measured in nanoamperes, making it suitable for battery-powered products that must run for years on a single cell. A PIC microcontroller (MCU) is a compact single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals such as timers, communication interfaces, and analog blocks. PIC24F devices use a 16-bit modified Harvard architecture with a multi-stage pipeline, sitting between the 8-bit PIC18 family and the 32-bit PIC32MX/CE families in Microchip's portfolio. The '24F' suffix denotes the family tier and Flash-based program memory, and the KM subfamily specifically targets low-power, analog-rich, low pin-count applications with integrated operational amplifiers that can be used as signal conditioning front-ends before the ADC. Key features of the PIC24F08KM101-I/P include flexible Capture/Compare/PWM (CCP) modules for motor control or timing, a Configurable Logic Cell (CLC) that allows users to build custom digital peripherals from on-chip signals, an integrated 12-bit ADC with sample-and-hold, and on-chip op-amps and a DAC for analog signal chains. The device also includes multiple communication peripherals, watchdog timers, and an in-circuit serial programming (ICSP) port that allows Flash programming without removing the chip from the board. Typical applications for this part include industrial sensor nodes, low-power IoT endpoints, battery-powered handheld instruments, home appliances, white goods control boards, and small motor or fan control modules. The wide 1.8 V to 5.5 V supply range makes it especially attractive for products powered directly from a single lithium cell, two AA cells, or a regulated 3.3 V / 5 V rail, while the integrated op-amps simplify transducer-bridge designs such as temperature, pressure, or strain-gauge signal conditioning. When designing with this device, confirm the desired operating voltage range matches the KM (1.8 V–5.5 V) variant rather than the PIC24FV (2.0 V–5.5 V) variant. Use low-ESR decoupling capacitors on VDD/AVDD and place them within a few millimetres of the pins. For low-power sleep-mode designs, follow the nanoWatt XLP guidance in the datasheet to achieve the published deep-sleep currents, paying close attention to which peripherals are clocked during sleep. This page consolidates distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC24F08KM101-I/SO - 16-bit 32MHz 8KB Flash XLP MCU | Microchip
PIC24F08KM101-I/SO

PIC24F08KM101-I/SO - 16-bit 32MHz 8KB Flash XLP MCU | Microchip

The Microchip Technology PIC24F08KM101-I/SO is a 16-bit PIC24F microcontroller from the nanoWatt XLP eXtreme Low Power family, offering 8KB of Flash program storage and 1KB of RAM in a 20-pin SOIC package. Operating at up to 32 MHz with 16 MIPS instruction throughput, it delivers efficient 16-bit performance while drawing very little active and sleep current, making it suitable for battery-powered and energy-harvesting applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripherals into one IC. The PIC24F family uses a 16-bit modified Harvard architecture optimized for deterministic real-time control. Within the broader taxonomy, this device sits at: microcontroller -> 16-bit MCU -> PIC24F -> nanoWatt XLP family. It is designed for low pin count, low power applications that still demand higher performance than 8-bit cores can offer. Key differentiating features include: Configurable Logic Cell (CLC) for hardware state-machine glue logic without software overhead; multiple Capture/Compare/PWM (CCP/OC) modules for motor, lighting, and signal-generation control; a 12-bit A/D converter with up to 12 channels for sensor interfaces; 3V and 5V operating options (PIC24FV variants extend to 2.0V-5.5V); and on-chip temperature indicator, mTouch capacitive touch, and real-time clock/calendar peripherals. The 'I' suffix indicates the industrial -40C to +85C temperature range. Architecturally, the device combines a modified Harvard 16-bit core with peripheral pin select, dual-rail power, and deep-sleep modes drawing only nanoamp-class currents. Compared with 8-bit PIC16F predecessors, the 24F core doubles register width and instruction efficiency, so fewer cycles are needed per task. Typical applications include consumer appliances, sensor signal conditioning, LED lighting control, low-cost motor drivers, portable medical devices, and IoT edge nodes where the XLP nanoWatt sleep profile extends battery life beyond what classic MCUs allow. The wide analog/digital mix reduces external component count. Design consideration: Verify the I/V variant code carefully - PIC24F parts use 1.8-3.6V logic, while PIC24FV parts extend to 5.5V. Mixing these on a 5V rail will damage the F variant. This page synthesizes distributor pricing, drop-in same-package alternatives, AEO-optimized FAQ, and practical design notes that go beyond the manufacturer datasheet, giving engineers actionable intelligence for sourcing and migration decisions.

RFQ Contact