Products (46,000+)

STM32F031F4P6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics
STM32F031F4P6

STM32F031F4P6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics

The STMicroelectronics STM32F031F4P6 is a 32-bit Arm Cortex-M0 microcontroller operating up to 48 MHz, with 16 KB of Flash memory, in a 20-pin TSSOP package. It belongs to the STM32F0 entry-level MCU family and combines a compact RISC core, embedded Flash, and peripheral interfaces for cost-sensitive embedded-control designs. A microcontroller is a semiconductor device that integrates a processor core, memory, and peripherals into one package. The STM32F031F4P6 is specifically an Arm Cortex-M0 microcontroller within the STM32F0 family. Its architecture is designed for compact control systems where deterministic execution, low component count, and straightforward peripheral integration are more important than application-processor performance. The principal device ratings include a 48 MHz maximum operating frequency, 16 KB of programmable Flash organized as 16K × 8, 32-bit processing, and a 20-pin TSSOP package. The STM32F031F4P6 is appropriate for small control platforms that benefit from a high-performance Cortex-M0 core without requiring the memory or package size of a larger microcontroller. Its 48 MHz operating point provides additional timing headroom for GPIO control, serial communication, timer-based control, and system management functions. The 16 KB Flash capacity supports embedded boot code, application firmware, configuration data, and firmware updates within one integrated device. Because memory capacity is fixed, firmware size should be checked against the target application before PCB release. Typical uses include compact sensor controllers, small motor-control boards, industrial interface modules, battery-powered instruments, LED-control systems, and low-cost embedded accessories. The 20-pin TSSOP footprint can also simplify assembly where fine-pitch packages would increase production complexity or inspection requirements. PCB design should reserve all pins required by the selected STM32F031F4P6 pinout, connect the required programming and reset signals correctly, and provide suitable decoupling close to the supply pins. Review the complete pin-description, electrical-characteristics, and recommended-circuit sections in the manufacturer datasheet before finalizing the footprint and support components. This product page combines the manufacturer device characteristics with package, sourcing, replacement, and design guidance. It also highlights the distinction between electrically similar STM32F0 devices and a genuine pin-for-pin drop-in replacement, helping engineers reduce redesign risk while preserving firmware and PCB compatibility.

RFQ Contact
STM32F031F4P7 - 48MHz Cortex-M0 16KB Flash MCU | ST
STM32F031F4P7

STM32F031F4P7 - 48MHz Cortex-M0 16KB Flash MCU | ST

The STMicroelectronics STM32F031F4P7 is an ARM Cortex-M0 32-bit microcontroller operating at up to 48 MHz, with 16 KB of Flash memory, 4 KB of SRAM, and a 20-pin TSSOP package. The device operates from a 2.0 V to 3.6 V supply and supports an extended temperature range from -40 °C to +105 °C. Its 20-pin package and compact footprint suit cost-sensitive embedded products requiring fast processing, analog measurement, and serial connectivity in a small PCB area. A microcontroller is a programmable system-on-chip that integrates a CPU core, program memory, data memory, peripherals, and I/O into one component. The STM32F031F4P7 belongs to the STM32F0 family, a 32-bit Arm Cortex-M0 product line positioned for general-purpose embedded control. Within the product hierarchy, it combines a microcontroller with embedded Flash, SRAM, timers, an analog-to-digital converter, and communication peripherals. Key characteristics include a maximum 48 MHz operating frequency, 16 KB (16K x 8) Flash, and 4 KB of SRAM with hardware parity. The family documentation identifies up to nine timers, an ADC, and communication capabilities. A 2.0 V to 3.6 V operating range allows operation from regulated 2.5 V or 3.3 V rails. The extended -40 °C to +105 °C temperature range supports industrial environments where consumer-temperature parts would be unsuitable. The STM32F031F4P7 uses the Arm Cortex-M0 instruction set with a 32-bit architecture. Hardware parity in the SRAM helps detect memory faults, while the 48 MHz clock rate supports responsive control loops and time-sensitive peripheral operation. Because the device is available in a 20-pin TSSOP package, it offers a practical balance between I/O access, board area, assembly cost, and performance for compact embedded systems. Typical uses include low-cost sensor controllers, compact industrial monitoring modules, small motor-control subsystems, and communication-enabled edge devices. Its ADC supports analog signal acquisition, its timers support periodic measurement and output functions, and its serial interfaces allow connection to sensors, transceivers, and human-interface modules. Designers should allocate the 20-pin TSSOP footprint according to the manufacturer pinout and keep decoupling capacitors close to the supply pins. Confirm peripheral availability, alternate-function routing, and firmware support for the specific application before PCB release. The device operates from a 3.6 V maximum supply, so regulator tolerances and transients must remain inside that limit. This page combines the manufacturer product specification with package-level pinout guidance, drop-in family alternatives, application-oriented design notes, and a practical comparison table for engineers evaluating a TSSOP-20 Cortex-M0 replacement.

RFQ Contact
STM32F031F6P6 - 32-Bit 48MHz MCU, 32KB Flash | STMicroelectronics
STM32F031F6P6

STM32F031F6P6 - 32-Bit 48MHz MCU, 32KB Flash | STMicroelectronics

The STMicroelectronics STM32F031F6P6 is a 32-bit ARM Cortex-M0 microcontroller with a maximum operating frequency of 48 MHz, 32 KB of Flash memory, and a 20-pin TSSOP package. It is an entry-level member of the STM32F0 microcontroller family and is designed for compact embedded systems requiring efficient control processing, low-power operation, and integrated analog peripherals. A microcontroller is a programmable semiconductor device that integrates a processor core, memory, and peripherals on one die. The STM32F0 family combines an ARM Cortex-M0 RISC core with embedded Flash and SRAM in the broader hierarchy of embedded processors, microcontrollers, and semiconductor components. The STM32F031F6P6 is suited to applications that need deterministic control rather than a high-performance desktop-class processor. Key features include a 32-bit Cortex-M0 core operating at up to 48 MHz, 32 KB of Flash memory, and nine timers. The device also integrates an ADC and communication peripherals, as identified by the manufacturer documentation. Its 20-TSSOP package supports compact surface-mount PCB layouts. The P6 ordering code identifies this exact package configuration, so footprint and device-specific requirements should be checked against the manufacturer pin definition before layout release. Technically, the Cortex-M0 architecture provides a simple instruction set and deterministic execution suitable for control logic, monitoring, and low-to-moderate data-processing tasks. The 48 MHz operating point gives the core more performance headroom than many basic 8-bit alternatives while retaining a small, accessible embedded platform. Peripheral integration also reduces the number of separate analog and timing components required in a typical embedded control design. Typical applications include industrial sensor controllers, compact automation modules, battery-powered monitoring equipment, lighting controls, small motor-control subsystems, and consumer accessories. An ADC supports analog input measurement, while the timer resources can be used for timing, pulse generation, and periodic control functions. For PCB design, use the manufacturer's 20-pin TSSOP land pattern and pin descriptions, place decoupling capacitors close to the power pins, and keep sensitive analog routing away from fast switching nodes. Confirm the exact pin assignments, peripheral multiplexing, clock configuration, and unused-pin requirements in the manufacturer datasheet before production. This page organizes the device identity, package information, verified manufacturer and distributor references, commercially relevant sourcing answers, candidate drop-in alternatives, and engineering-focused selection guidance into a concise resource for embedded-product designers.

RFQ Contact
STM32F031G4U6 - 48MHz Cortex-M0 MCU 16KB Flash | STMicroelectronics
STM32F031G4U6

STM32F031G4U6 - 48MHz Cortex-M0 MCU 16KB Flash | STMicroelectronics

The STMicroelectronics STM32F031G4U6 is an ARM Cortex-M0 32-bit RISC microcontroller operating at up to 48 MHz, integrating 16 KB of Flash memory and 4 KB of SRAM in a 28-pin UFQFPN (4x4 mm) package. The device operates from a 2.0 V to 3.6 V supply, supporting both 2.5 V and 3.3 V typical rails used by sensor, motor, and human-machine-interface (HMI) designs. The suffix "U6" denotes the UFQFPN-28 tape-and-reel packaging option qualified for industrial -40 °C to +85 °C operation. A microcontroller (MCU) is a single-chip processor that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripheral interfaces such as timers, communication controllers, and analog blocks. Within the broader semiconductor taxonomy, an MCU belongs to the microcontroller family, which sits inside the integrated-circuit (IC) hierarchy and the embedded-computing product domain. Cortex-M0 is ARM's smallest and most energy-efficient core, designed for deterministic real-time control with a minimal instruction set and ultra-low gate count. Key specifications include a 12-bit ADC with up to 10 external channels, a 16-bit advanced-control timer for motor driving, multiple 16-bit and 32-bit general-purpose timers, communication interfaces (I2C, SPI, USART), an integrated voltage reference, brown-out reset (BOR), and a watchdog timer. The UFQFPN-28 footprint exposes 23 GPIO and embeds a 1-channel DMA controller for offloading data moves from the core, improving determinism in interrupt-driven loops. The architecture uses a single AHB-Lite bus matrix connecting the Cortex-M0 core, Flash, SRAM, and peripherals. The advanced-control timer supports complementary PWM outputs with dead-time insertion and an emergency stop input, making the part well-suited for brushless-DC (BLDC) and permanent-magnet synchronous motor (PMSM) commutation. The 12-bit ADC achieves a 1 µs conversion time and supports hardware oversampling to reach 16-bit effective resolution when required. Typical applications include BLDC and stepper motor control (small fans, pumps, e-bike throttles), sensor nodes and home-automation bridges, low-cost HMI panels and e-metering front-ends, industrial 24 V→3 V signal-conditioning modules, and consumer appliances requiring low pin-count, deterministic control. The wide 2.0–3.6 V range supports direct connection to a single Li-ion cell or to a regulated 3.3 V LDO downstream of a 5 V or 12 V bus. When designing with this MCU, plan the decoupling network (100 nF + 4.7 µF close to VDD pins) and ensure NRST is pulled up with the recommended 10 kΩ and a 100 nF capacitor for noisy industrial enclosures. The BOOT0 pin must be tied to GND through a 10 kΩ resistor on production boards to lock the part into main-Flash boot; floating BOOT0 is a common field-failure cause.

RFQ Contact
STM32F031G4U7 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics
STM32F031G4U7

STM32F031G4U7 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics

STMicroelectronics STM32F031G4U7 is an ARM Cortex-M0 32-bit microcontroller operating at up to 48 MHz, with 16 KB of Flash memory in a 28-pin UFQFPN package measuring 4 x 4 mm. The device belongs to the STM32F0 access-line family and combines a compact footprint with embedded control and analog-processing resources. A microcontroller is a semiconductor device that integrates a processor core, memory, peripherals, and input/output interfaces on one integrated circuit. Its ARM Cortex-M0 architecture executes instructions using a reduced instruction set intended for embedded control. Within the product hierarchy, this STM32F0 device belongs to the STM32 family of 32-bit embedded microcontrollers and provides a practical bridge between simple discrete logic and more complex application processors. Key features include a maximum 48 MHz operating frequency, 16 KB of Flash memory, a 28-pin UFQFPN package, and an operating supply identified as 2.5 V or 3.3 V in the product listing. The STM32F03 family also provides nine timers, an analog-to-digital converter, and communication resources. These functions support periodic measurement, motor or actuator control, signal acquisition, and serial communications without requiring multiple discrete components. The STM32F031G4U7 combines a 32-bit ARM Cortex-M0 processing core with on-chip Flash and mixed-signal peripherals. A 4 x 4 mm UFQFPN package supports compact PCB layouts, but its 28 fine-pitch leads and exposed thermal pad require careful land-pattern, solder-paste, and assembly design. The 16 KB Flash capacity is appropriate for compact control firmware, bootloader code, and moderate protocol stacks rather than graphics-intensive or large data-logging applications. Typical applications include industrial sensor nodes, compact medical monitoring instruments, smart-home controls, portable measurement equipment, communication modules, and small motor-control boards. The combination of timers, ADC capability, communication peripherals, and a 48 MHz core allows designers to consolidate basic control and sensing functions into one embedded platform while retaining a small footprint. Designers should verify the complete pin assignment, exposed-pad connection, decoupling requirements, clock configuration, and programming interface against the manufacturer datasheet before PCB release. Firmware development should also confirm the required development tool, debugger, bootloader support, and peripheral mapping for the selected STM32F03 device. This product page organizes the manufacturer specifications, sourcing information, qualified alternatives, and practical design guidance for engineers evaluating the STM32F031G4U7 in compact embedded systems.

RFQ Contact
STM32F031G6U6 - 48MHz Cortex-M0 32KB MCU | STMicroelectronics
STM32F031G6U6

STM32F031G6U6 - 48MHz Cortex-M0 32KB MCU | STMicroelectronics

The STMicroelectronics STM32F031G6U6 is an ARM Cortex-M0 32-bit RISC microcontroller operating at up to 48 MHz, with 32 KB of Flash memory, 4 KB of SRAM, and a 28-pin UFQFPN package. The device supports a 2.0 V to 3.6 V operating range and combines nine timers, one 12-bit ADC, and serial interfaces including I2C, SPI/I2S, and USART. It is intended for compact embedded-control designs that need efficient 32-bit processing without the cost or complexity of a higher-performance MCU. A microcontroller is an integrated circuit containing a processor core, nonvolatile program memory, volatile working memory, peripherals, and input/output circuitry. The STM32F031G6U6 belongs to the STM32F0 family and sits within the broader hierarchy of embedded microcontroller, 32-bit RISC processor, Arm Cortex-M processor, and semiconductor. Its compact package and mixed-signal peripherals make it suitable for cost-sensitive control, sensing, communication, and motor-adjacent products. The principal resources include 32 KB of Flash, 4 KB of SRAM, and a maximum CPU frequency of 48 MHz. Its communication peripherals comprise one I2C interface, one SPI or I2S interface, and one USART. For analog measurements, the MCU includes one 12-bit ADC. Nine timers support periodic timing, input capture, output compare, PWM generation, and other time-dependent control functions. These resources allow the MCU to consolidate several discrete functions on a single board. The STM32F031G6U6 uses an Arm Cortex-M0 core with a 32-bit RISC architecture. The core executes compact firmware from embedded Flash while using SRAM for working data and the stack. Its 48 MHz maximum operating frequency provides useful headroom for digital control loops, serial protocol handling, and periodic sensor processing. The 12-bit ADC resolution is suitable for many industrial control, consumer accessory, and compact instrumentation applications where higher-resolution conversion is not required. Typical uses include sensor-hub and environmental-monitoring nodes, small motor controllers, digital control panels, communication modules, and compact consumer products. Designers can use the I2C interface for sensors and EEPROMs, SPI or I2S for higher-speed peripherals or digital audio devices, and USART for point-to-point links. The nine timers allow multiple PWM or capture channels to be allocated without adding separate timing peripherals. Board design should preserve clean separation between analog and digital returns, route sensitive ADC inputs away from switching nodes, and place decoupling capacitors close to the power pins. Firmware and peripheral assignments should be checked against the manufacturer pin description and pinout before PCB release. This page also organizes package, interface, memory, sourcing, and replacement considerations into a single engineering reference for design-in decisions. The STM32F031G6U6 is best evaluated against the complete design rather than by clock speed alone. Verify voltage, memory, ADC, timer, serial-interface, package, and software requirements together. A lower-cost or newer-family device is only a drop-in replacement when its electrical limits, pin assignment, peripheral behavior, clock tree, firmware assumptions, and qualification requirements have all been reviewed against the original design.

RFQ Contact
STM32F031K4U6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics
STM32F031K4U6

STM32F031K4U6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics

The STMicroelectronics STM32F031K4U6 is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 16 KB of Flash memory and 27 I/O pins, housed in a 32-pin UFQFPN 5 x 5 mm package. The device provides 2.5 V and 3.3 V supply options and is positioned as an entry-level embedded-control MCU for compact industrial, consumer, communications, and automation products. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals on one device. The STM32F031K4U6 belongs to the hierarchy MCU -> embedded microcontroller -> ARM Cortex-M0 microcontroller -> STM32F0 series. Its Cortex-M0 architecture provides a 32-bit RISC processing environment while supporting peripherals commonly required for embedded products, including LIN, timers, PWM, SPI, UART/USART, I2C, IrDA, DMA, I2S, POR, and watchdog functions. The principal feature set includes a 48 MHz maximum operating frequency, 16 KB Flash program memory, a 32-pin compact package, and up to 27 I/O pins. The Flash-oriented organization of 16K x 8 supports embedded firmware storage, while the 5 x 5 mm UFQFPN package is suitable for space-constrained assemblies. Available sourcing information identifies this exact ordering code as a 2.5 V or 3.3 V device. The STM32F031K4U6 combines a general-purpose Cortex-M0 core with serial communication and timing resources suited to real-time control. Its reported peripherals include I2C, IrDA, LINbus, SPI, UART/USART, DMA, I2S, POR, PWM, and WDT. These interfaces allow the MCU to connect sensors, actuators, human-interface devices, communications transceivers, and audio converters without requiring several separate interface devices. Typical uses include compact sensor nodes, industrial control modules, LIN-connected peripherals, communication equipment, motor and actuator controllers, and small consumer products. The 48 MHz processing rate provides additional timing margin for interrupt-driven control and protocol handling, while the 27 available I/O pins support multiple digital connections on a compact board. Designers should verify the exact exposed-pad connection, decoupling requirements, clock configuration, and peripheral pin assignments against the manufacturer documentation before layout release. The target package is a 32-pin UFQFPN, and the thermal behavior of its exposed pad depends on the PCB copper area, solder mask, and thermal via arrangement. The verified excerpts do not provide the complete pin names, so no pin-level assignments are inferred here. This product page consolidates verified distributor pricing, package and memory details, sourced drop-in candidates, and practical selection guidance. It distinguishes documented STM32F031K4U6 attributes from compatibility claims that require schematic, firmware, ADC, clock, and low-power validation before production substitution.

RFQ Contact
STM32F031K6T6 - 48MHz Cortex-M0 MCU | STMicroelectronics
STM32F031K6T6

STM32F031K6T6 - 48MHz Cortex-M0 MCU | STMicroelectronics

STMicroelectronics STM32F031K6T6 is an ARM Cortex-M0 32-bit RISC microcontroller operating at up to 48 MHz, with 32 KB of Flash memory, 4 KB of SRAM, and a 32-LQFP 7 x 7 mm package. The device also provides 25 I/Os, nine timers, a 12-bit ADC, one I2C interface, one SPI/I2S interface, one USART, and operation from 2.0 V to 3.6 V. A microcontroller is a programmable system-on-chip that combines a processor core, nonvolatile program memory, volatile data memory, peripherals, and general-purpose I/O in one package. The STM32F031 belongs to the STM32F0 access-line family, where ARM Cortex-M0 -> 32-bit RISC microcontroller -> embedded microcontroller -> semiconductor forms the relevant product hierarchy. Its compact package and mixed-signal peripherals suit cost-sensitive embedded-control products that require deterministic control without a higher-performance MCU. Key features include a 48 MHz ARM Cortex-M0 core, 32 KB of Flash for firmware storage, and 4 KB of SRAM for working memory. The 12-bit ADC supports analog measurement, while the I2C, SPI/I2S, and USART interfaces cover sensor buses, serial peripherals, and point-to-point communication. Nine timers support periodic and timing functions, and the 2.0 V to 3.6 V operating range permits integration with common 3.3 V embedded systems. The STM32F031K6 architecture emphasizes compact control rather than high-performance computation. Its 32-bit Cortex-M0 instruction set provides efficient control-loop execution, while the integrated analog and serial peripherals reduce the need for external components. Available SRAM and Flash should be checked against the final application, particularly when buffering samples, maintaining protocol stacks, or supporting bootloader features. Typical applications include compact sensor controllers, small motor-control systems, industrial monitoring nodes, digital control modules, battery-powered instruments, and communication equipment. The STM32F031K6T6 is particularly relevant where 48 MHz processing, 25 I/Os, and multiple serial interfaces are required within a 32-LQFP footprint. Designers should verify the exact pin assignment, alternate-function requirements, decoupling network, clock configuration, and peripheral instance mapping against the manufacturer datasheet. The 2.0 V minimum supply imposes a 3.3 V rail design constraint, and firmware should include reset, clock, ADC-calibration, and brownout handling appropriate to the selected power architecture. This page consolidates the verified manufacturer specifications, distributor availability references, cross-reference evidence, and engineering guidance into a structured selection resource. It distinguishes verified drop-in evidence from generic MCU alternatives and highlights the limits of using an unqualified third-party replacement in production.

RFQ Contact
STM32F031K6U6 - 48MHz Cortex-M0 MCU 32KB Flash | STMicroelectronics
STM32F031K6U6

STM32F031K6U6 - 48MHz Cortex-M0 MCU 32KB Flash | STMicroelectronics

The STM32F031K6U6 is a 32-bit entry-level microcontroller from STMicroelectronics based on the ARM Cortex-M0 core, operating at up to 48 MHz with 32 KB of Flash memory and 4 KB of SRAM in a compact 32-pin UFQFPN (5x5 mm) package with exposed pad. A microcontroller (MCU) is a single-chip embedded processor combining a CPU core, memory, and programmable peripherals. The STM32F031K6U6 belongs to the STM32F0 entry-level family within the STM32 MCU ecosystem, positioned as a migration path from 8-bit and 16-bit MCUs to 32-bit ARM performance. It shares tooling, HAL libraries, and STM32CubeMX configuration software with the wider STM32 portfolio, simplifying future upgrades. Key features include a 12-bit ADC with up to 13 channels, 9 timers, and standard communication interfaces: one I2C, one SPI/I2S, and one USART. The device operates from a 2.0V to 3.6V single supply with integrated POR/PDR reset, and offers a CRC calculation unit and DMA controller for data movement without CPU intervention. Real-time performance is supported by a nested vectored interrupt controller (NVIC) and single-cycle multiplier. The Cortex-M0 architecture executes Thumb instruction sets with deterministic interrupt latency, making the device suitable for real-time control loops. The UFQFPN-32 (QFN family) surface-mount package provides a small 5x5 mm footprint with an exposed thermal pad for grounding, ideal for space-constrained boards. Operating temperature spans -40C to +85C for industrial reliability. Typical applications include industrial control, consumer appliances, IoT sensor nodes, small motor control, and power-management subsystems, where low cost, low power consumption, and adequate peripheral integration matter most. Design tip: decouple VDD pins with 100nF ceramics plus a bulk capacitor, feed VDDA from a clean analog supply to preserve ADC accuracy, and keep NRST properly filtered per the ST datasheet layout guidelines for EMI-robust designs.

RFQ Contact
STM32F038F6P6 - 48MHz Cortex-M0 32KB MCU | STMicroelectronics
STM32F038F6P6

STM32F038F6P6 - 48MHz Cortex-M0 32KB MCU | STMicroelectronics

STMicroelectronics STM32F038F6P6 is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 32 KB of embedded Flash memory, in a 20-pin TSSOP package. The device supports low-voltage operation identified at 1.8 V, 2.5 V, and 3.3 V, making it suitable for compact embedded products that require an economical 32-bit control architecture. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. In the product hierarchy, the STM32F038F6P6 belongs to the STM32F0 family of 32-bit embedded microcontrollers, uses the ARM Cortex-M0 processor core, and operates within the broader category of embedded systems semiconductors. Its reduced instruction set is designed for efficient control tasks rather than high-complexity application processing. Key features include a maximum core frequency of 48 MHz and 32 KB of Flash organized as 32K × 8 bits. The 20-TSSOP package provides a compact surface-mount footprint, while the listed operating voltages support common low-voltage embedded rails. Its Cortex-M0 architecture and 32-bit datapath provide useful processing capability for real-time control, sensor acquisition, communication, and human-interface tasks without requiring a higher-performance processor core. The STM32F038F6P6 belongs to STMicroelectronics' STM32F038x6 family, which is positioned around a high-performance Cortex-M0 core and high-speed embedded control. Its combination of 48 MHz operation, 32 KB Flash, and 20-pin packaging makes it particularly useful where PCB area is constrained but deterministic control and moderate peripheral integration remain important. Developers should select the device against the detailed peripheral, clock, and electrical requirements in the manufacturer datasheet. Typical uses include compact motor-control modules, low-cost condition-monitoring devices, simple user-interface controllers, sensor hubs, and industrial accessories. A 48 MHz Cortex-M0 can manage multiple interrupt-driven tasks and communication routines, while the 32 KB Flash budget can hold a bootloader and application code when code size is carefully managed. The primary design consideration is package and pin planning. Use the pin-description table in the STM32F038F6P6 manufacturer datasheet when assigning alternate-function pins, programming pins, and power pins. Confirm the selected board's operating voltage and decoupling arrangement, and verify all peripheral assignments against the exact package variant before releasing the PCB layout. This page combines manufacturer product information, distributor observations, package details, source-backed pricing, drop-in alternatives, and practical design guidance to support faster component selection. It also distinguishes confirmed electrical attributes from parameters that still require direct verification against the manufacturer datasheet.

RFQ Contact
STM32F042C4T6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics
STM32F042C4T6

STM32F042C4T6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics

The STMicroelectronics STM32F042C4T6 is a 32-bit ARM Cortex-M0 microcontroller operating at up to 48 MHz, with 16 KB of Flash memory, 6 KB of SRAM, USB full-speed, CAN, and a 12-bit ADC, housed in a 48-LQFP 7 x 7 mm package. It is designed for compact embedded-control products requiring USB connectivity, CAN communication, and a broad set of serial peripherals. A microcontroller, or MCU, integrates a processor core, memory, peripherals, and communication interfaces on one semiconductor device. The STM32F0 family belongs to the Arm Cortex-M0 microcontroller hierarchy and combines a low-complexity 32-bit instruction set with deterministic embedded control. In the STM32F042C4T6, the CPU executes from embedded Flash while SRAM supports working data and stack operations. USB, CAN, USART, SPI, and I2C support connected products, industrial controls, and service equipment. The device combines a 48 MHz maximum operating frequency, 16 KB Flash, and 6 KB SRAM with a 12-bit ADC capable of handling up to 10 channels. USB 2.0 full-speed, CAN, multiple USART and SPI interfaces, I2C, timers, and a CEC-related feature make it suitable for compact USB-aware control nodes. The 48-LQFP package provides 48 externally accessible pins and is appropriate for designs requiring conventional leaded-package assembly and inspection. The STM32F042C4T6 is positioned as a mainstream Arm Cortex-M0 MCU with a 2.5 V to 3.6 V supply range, as identified in distributor listings. Its 48-pin LQFP footprint simplifies access to communication and general-purpose I/O compared with smaller packages. Designers should confirm the complete pin multiplexing, clock, USB, CAN, and analog specifications against the manufacturer datasheet before releasing a production board. Typical applications include USB-connected peripheral controllers, industrial communication modules, CAN nodes, data-acquisition equipment, consumer accessories, and compact embedded-control systems. The MCU can act as the central controller for a USB peripheral while using CAN or serial interfaces for local communication. Its 12-bit ADC supports analog monitoring, while timers and GPIO provide control and sensing connections. Design guidance focuses on preserving USB signal integrity and separating analog, digital, and return-current paths. Place USB differential routing over a continuous reference plane, keep the USB transceiver and decoupling components close to their relevant pins, and validate firmware clocks and peripheral initialization against the manufacturer reference procedure. This page consolidates verified distributor specifications, sourcing information, and engineering-oriented usage guidance.

RFQ Contact
STM32F042C6T6 - 48MHz Cortex-M0 32KB Flash USB MCU | STMicroelectronics
STM32F042C6T6

STM32F042C6T6 - 48MHz Cortex-M0 32KB Flash USB MCU | STMicroelectronics

The STMicroelectronics STM32F042C6T6 is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 32 KB of Flash memory, 6 KB of SRAM, USB full-speed device support, and CAN connectivity in a 48-LQFP package. It is designed for compact USB-connected embedded systems requiring a low-cost, low-power general-purpose MCU. A microcontroller integrates a CPU core, memory, and peripheral blocks into one semiconductor device. The STM32F0 family uses an Arm Cortex-M0 core within the broader 32-bit embedded microcontroller hierarchy, providing deterministic control performance, efficient interrupt handling, and a broad ecosystem of software development tools. The STM32F042C6T6 targets USB, CAN, industrial-control, consumer-electronics, and accessory applications. The device operates from a 2.5 V or 3.3 V supply, as identified in the distributor listing. Its 48 MHz maximum operating frequency supports responsive control loops and USB full-speed device communication compliant with USB 2.0. The integrated USB device peripheral includes an internal USB PHY and embedded DP pull-up, while the datasheet summary identifies battery-charging detection support according to the Battery Charging Specification Revision 1.2. The STM32F042x4/x6 family also provides a CAN peripheral, making the MCU appropriate for industrial and embedded communication systems. The 48-LQFP 7x7 mm package exposes the required GPIO, communication, power, debug, and clock connections in a widely manufacturable surface-mount format. Typical uses include USB-connected configuration tools, data acquisition modules, compact industrial controllers, CAN-connected sensor nodes, and USB peripheral accessories. The 32 KB Flash capacity is appropriate for applications with moderate firmware size, while the 48 MHz core provides useful performance margin for protocol handling and real-time control. Designers should confirm the exact pin multiplexing, crystal requirements, USB implementation guidance, and decoupling values against the manufacturer datasheet before layout. This page combines distributor availability data, manufacturer specifications, package information, and application guidance to support component selection and sourcing.

RFQ Contact
STM32F042C6U6 - 48MHz, 32KB Flash Cortex-M0 MCU | ST
STM32F042C6U6

STM32F042C6U6 - 48MHz, 32KB Flash Cortex-M0 MCU | ST

The STMicroelectronics STM32F042C6U6 is an ARM Cortex-M0 32-bit microcontroller operating up to 48 MHz, with 32 KB Flash memory and a 48-pin UFQFPN 7 x 7 mm package. Its USB, CAN, timers, ADC, and communication interfaces make it suitable for connected embedded control, USB accessories, industrial sensing, and compact consumer products. The STM32F0 architecture combines a deterministic RISC core with extensive peripheral integration in a low-pin-count surface-mount package. A microcontroller is a semiconductor that integrates a processor core, program memory, data memory, and peripherals such as timers, serial interfaces, analog converters, and communication controllers. The STM32F042C6U6 belongs to the STM32F0 family, where the Cortex-M0 core sits at the lowest-complexity level of the ARM Cortex-M portfolio. This hierarchy makes the device appropriate for control-oriented products that need broad peripheral support without requiring a higher-performance application processor. Key verified features include a 48 MHz maximum operating frequency, 32 KB Flash, a 32-bit ARM Cortex-M0 core, and crystal-less USB full-speed support identified in the available datasheet preview. Distributor listings also identify USB and CAN functionality. The 48-UFQFPN package measures 7 x 7 mm and includes an exposed pad according to the supplied component listings, supporting compact layouts while providing a dedicated thermal and grounding connection area subject to the manufacturer's layout guidance. The STM32F0 architecture supports embedded firmware development around standard serial interfaces, analog measurement, timing, and USB communication. At 48 MHz, the MCU provides more timing margin for protocol handling, control loops, and peripheral coordination than lower-frequency STM32F0 devices. Because the verified data does not state SRAM size, ADC resolution, timer channels, or exact USB electrical limits, those values should be confirmed in the official STM32F042x4/x6 documentation before final design signoff. Typical uses include USB-to-serial or configuration accessories, low-cost CAN-connected nodes, industrial sensor controllers, compact motor-control auxiliaries, and USB-powered embedded products. The MCU is especially attractive when designers want STM32 tooling and firmware portability while retaining a compact UFQFPN footprint. Firmware, boot configuration, clocking, low-power behavior, and peripheral pin multiplexing must be selected from the manufacturer's device documentation rather than inferred from distributor summaries. For PCB implementation, follow the official UFQFPN land pattern and exposed-pad recommendations exactly. Place decoupling capacitors close to each applicable supply pin, route high-speed USB signals as a controlled differential pair, and preserve the manufacturer's thermal-pad copper and via guidance. Confirm oscillator, reset, boot, and USB requirements for the selected board configuration. This page synthesizes the verified distributor inventory, package information, architecture, and engineering considerations into a compact design reference. This product data is limited to facts present in the supplied verified web results and deliberately identifies unverified parameters instead of guessing. Lifecycle, electrical limits, pin names, memory-map details, and absolute maximum ratings require confirmation from STMicroelectronics before production release.

RFQ Contact
STM32F042F4P6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics
STM32F042F4P6

STM32F042F4P6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics

The STMicroelectronics STM32F042F4P6 is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 16 KB of Flash memory, 6 KB of SRAM, and USB, CAN, and CEC connectivity in a 20-pin TSSOP package. The device is designed for compact embedded systems requiring a low-cost general-purpose MCU, a USB peripheral, and communication interfaces in a small surface-mount footprint. A microcontroller is an integrated semiconductor containing a processor core, memory, and peripherals on one chip. The STM32F0 MCU family belongs to the embedded-processing hierarchy: microcontroller → 32-bit RISC MCU → ARM Cortex-M0 microcontroller → embedded-control device. Its combination of 48 MHz processing speed, USB connectivity, and a 20-pin package makes it useful for USB-connected control, industrial interface, and compact consumer products. Key features include a 32-bit ARM Cortex-M0 core, 48 MHz maximum operating frequency, and 16 KB of Flash for firmware storage. The device also provides 6 KB of SRAM and integrated USB, CAN, and CEC functions. Its 2.4 V to 3.6 V operating-supply range suits 3.3 V systems, while the 20-TSSOP package supports compact, high-density PCB layouts. These characteristics balance processing performance and interface coverage without requiring a larger pin count. The STM32F0 architecture is based on a 32-bit reduced-instruction-set-computing core intended for efficient embedded control. Flash-resident code and SRAM support boot-time firmware, event handling, communication stacks, and peripheral control, while USB and CAN provide paths for connected equipment and industrial networking. The USB and CAN interfaces distinguish this device from basic Cortex-M0 microcontrollers that support only serial or general-purpose interfaces. Typical applications include USB human-interface-interface accessories, compact industrial controllers, CAN-connected sensors, consumer electronics, and battery-operated equipment. The MCU can also manage LED interfaces, communication bridges, and low-speed embedded control tasks where board area is constrained. Its 20-pin package and 3.3 V supply architecture simplify integration into compact USB dongles, control modules, and secondary embedded processors. Designers should reserve all 20 TSSOP positions, route the USB data and power pins according to the manufacturer reference design, and confirm firmware support for the selected USB, CAN, and CEC peripheral configuration before PCB release. The 16 KB Flash limit requires attention to bootloader size, protocol libraries, and application code. For a production migration, verify pin multiplexing, clock setup, peripheral mapping, and interrupt behavior against the manufacturer datasheet. This page combines the official STM32F042F4 product information, exact-order-code listings, interface and memory details, same-brand drop-in alternatives, and practical integration guidance. It is intended to accelerate part selection, schematic review, firmware planning, and footprint verification for engineers designing with the STM32F042F4P6.

RFQ Contact
STM32F042F6P6 - 48MHz Cortex-M0 32KB MCU | STMicroelectronics
STM32F042F6P6

STM32F042F6P6 - 48MHz Cortex-M0 32KB MCU | STMicroelectronics

The STMicroelectronics STM32F042F6P6 is a 32-bit ARM Cortex-M0 microcontroller in a 20-pin TSSOP package, operating at up to 48 MHz with 32 KB of Flash memory, USB, and CAN connectivity. The device is designed for compact embedded systems that require a fast Cortex-M0 core and dedicated USB or CAN communication without the resource demands of a larger microcontroller family. According to the manufacturer product page, the STM32F042x4/x6 series combines high-performance embedded processing with a rich peripheral set for cost-sensitive control, communications, and human-interface applications. A microcontroller is a programmable system-on-chip that integrates a CPU core, Flash program memory, SRAM, peripherals, and communication interfaces onto one package. Within the product hierarchy, the STM32F042F6P6 is an ARM Cortex-M0 microcontroller, a 32-bit RISC device within the STM32F0 family, and a member of the broader embedded-processing and power-management ecosystem. Its 48 MHz operating frequency supports responsive control loops, while the USB and CAN peripherals provide dedicated paths for personal-computer connectivity and industrial or automotive network communication. Key features include a 48 MHz ARM Cortex-M0 core, 32 KB of Flash memory, a 12-bit ADC, USB and CAN interfaces, and operation from 2.5 V to 3.3 V. The 20-pin TSSOP package measures 4.4 mm in body width and is intended for surface-mount assembly. The -40 °C to +85 °C temperature range supports industrial-temperature commercial equipment, although extended-temperature variants should be selected when wider environmental margins are required. The STM32F0 architecture provides a practical balance between processing performance, peripheral integration, and low system complexity. Its 32-bit instruction set and dedicated communication blocks allow firmware consolidation when a design otherwise needs separate USB and CAN interface controllers. Peripheral multiplexing should be checked against the selected board configuration because assigning USB, CAN, timers, and general-purpose I/O can limit the number of simultaneously available port pins. Typical applications include USB-connected control panels, CAN-connected sensor nodes, compact industrial controllers, USB-to-serial adapters, small human-interface products, and embedded systems that require a low-pin-count Cortex-M0 implementation. The MCU also suits compact actuator controllers and peripheral modules where a USB service interface simplifies configuration and firmware updates. When laying out the board, place the decoupling capacitors beside the power pins, route the USB data lines as a controlled impedance pair, and keep the CAN transceiver interface away from sensitive analog paths. Confirm the exact peripheral-pin multiplexing, clock configuration, and pin electrical limits in the manufacturer datasheet before releasing the PCB layout.

RFQ Contact
STM32F042F6P7 - 48MHz Cortex-M0 MCU, 32KB Flash | STMicroelectronics
STM32F042F6P7

STM32F042F6P7 - 48MHz Cortex-M0 MCU, 32KB Flash | STMicroelectronics

STMicroelectronics STM32F042F6P7 is an ARM Cortex-M0 32-bit microcontroller operating up to 48 MHz, with 32 KB (32K x 8) Flash memory and USB, CAN, and other connectivity, in a 20-TSSOP package. It belongs to the STM32F0 family of compact, low-power embedded MCUs for cost-sensitive control applications. A microcontroller integrates a CPU core, program memory, data memory, peripherals, and communication interfaces on one semiconductor device. The STM32F0 series provides a simple architecture for embedded control, while this part adds USB and CAN connectivity for connected industrial, automotive, and consumer equipment. The STM32F042x4/x6 family description identifies the Cortex-M0 core and 48 MHz maximum operating frequency. Key verified features include a 32-bit ARM Cortex-M0 core, 48 MHz maximum clock frequency, and 32 KB Flash program memory. The 20-TSSOP package supports compact PCB layouts, and the exact suffix P7 identifies the supplied device ordering variant. The Mouser listing also identifies the part as a mainstream ARM Cortex-M0 USB-line MCU with 32 KB Flash, USB, and CAN. The STM32F042F6P7 combines a compact 20-pin TSSOP with general-purpose embedded-control capability and wired connectivity. It is suitable for designs that need more than basic GPIO control but do not require a high-pin-count package. The verified data does not specify RAM size, operating-voltage range, GPIO count, ADC details, timers, or package dimensions, so those values must be confirmed in the manufacturer documentation before final design release. Typical uses include USB-connected human-interface devices, CAN-connected industrial controls, compact sensor nodes, automotive accessories, low-cost communication equipment, and small controller boards. Its 48 MHz Cortex-M0 core provides useful processing headroom while retaining the simple programming model associated with ARM Cortex-M devices. Designers should treat the 20-TSSOP footprint, pin multiplexing, power requirements, clock strategy, and USB or CAN transceiver integration as the critical review points. A MCU cannot connect directly to a physical USB or CAN bus without the appropriate external circuitry, protection, routing, and signal-integrity implementation. This page combines verified manufacturer and distributor facts, transparent data gaps, package information, application guidance, and practical design cautions. It helps engineers distinguish confirmed STM32F042F6P7 characteristics from parameters that still require verification from the official datasheet.

RFQ Contact
STM32F042G6U6 - 48MHz Cortex-M0 USB MCU | STMicroelectronics
STM32F042G6U6

STM32F042G6U6 - 48MHz Cortex-M0 USB MCU | STMicroelectronics

The STMicroelectronics STM32F042G6U6 is a 32-bit ARM Cortex-M0 microcontroller operating at up to 48 MHz, with 32 KB of embedded Flash memory and USB and CAN connectivity in a 28-pin UFQFPN package measuring 4 mm by 4 mm. It targets compact embedded systems that need deterministic control, USB connectivity, and CAN communication without requiring a larger microcontroller package. A microcontroller, or MCU, is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and I/O into one package. The STM32F0 family belongs to the 32-bit embedded-controller segment of the broader semiconductor hierarchy. This combination of compact packaging, USB, CAN, and a 48 MHz Cortex-M0 core makes the STM32F042G6U6 useful for cost-sensitive human-interface, communications, industrial-control, and accessory designs. The STM32F042G6U6 provides 32 KB of Flash for firmware and 32-bit processing through the ARM Cortex-M0 core. Its listed communications features include USB and CAN, while its 28-pin UFQFPN package supports compact board layouts. The 48 MHz operating frequency provides additional timing margin for protocol handling, control loops, and user-interface tasks. Exact RAM, peripheral-count, voltage-range, and temperature-range values should be confirmed in the manufacturer datasheet before a production release. The STM32F042x4/x6 architecture is designed around STMicroelectronics’ ARM Cortex-M0 implementation, combining a compact RISC core with embedded control peripherals and integrated communications. USB support allows the MCU to enumerate as a USB device, while CAN provides a standardized interface for industrial and vehicle-related networking. Firmware migration within the STM32F0 ecosystem is easier when the device family, clock configuration, peripheral set, and development toolchain are evaluated together rather than by clock speed alone. Typical applications include USB-connected control accessories, CAN-connected sensor modules, compact industrial controllers, USB-to-CAN interface boards, and embedded user-interface products. The 4 mm by 4 mm package is especially useful where connector density limits PCB area. Designers should reserve adequate board area for routing USB differential pairs and CAN signal paths while maintaining power and ground return continuity. Design the decoupling network around the device power pins and follow the recommended external-component arrangement in the manufacturer datasheet. USB differential routing requires controlled impedance, short matched traces, and a continuous ground reference. CAN networks also need correct termination and transceiver interfacing; the MCU’s CAN peripheral does not replace the physical CAN transceiver. Firmware, clock, bootloader, and peripheral configurations must be revalidated whenever the exact ordering code changes. This page combines the manufacturer product information with package, interface, application, replacement, and procurement guidance to help engineers evaluate the STM32F042G6U6 efficiently. It also distinguishes confirmed drop-in interchangeability from merely similar controllers, helping prevent a footprint-compatible but feature-incompatible substitution from entering a production design.

RFQ Contact
STM32F042K4T6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics
STM32F042K4T6

STM32F042K4T6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics

The STMicroelectronics STM32F042K4T6 is an ARM Cortex-M0 32-bit microcontroller with a 48 MHz clock, 16 KB Flash memory, and a 32-LQFP 7 x 7 mm package. It is part of the STM32F0 family and is described by distributor data as a mainstream MCU with USB, CAN, 2.5 V and 3.3 V supply options, and a 32-pin LQFP package. These characteristics place it in the connected embedded-control segment, where moderate processing speed and serial connectivity are more important than high flash capacity. What is an ARM Cortex-M0 microcontroller? An MCU is an integrated semiconductor containing a processor core, memory, peripherals, and interfaces on one package. The ARM Cortex-M0 is a compact 32-bit embedded processor core designed for cost-sensitive, energy-efficient control systems. In the STM32F0 family, it supports embedded control, USB communications, CAN networking, and general-purpose peripherals within a small power-management and processing footprint. Key features include a 48 MHz maximum CPU frequency and 16 KB of Flash memory. The verified distributor listing identifies 16 KB organized as 16K x 8 and identifies USB and CAN connectivity. The STM32F042K4T6 is also listed with 2.5 V and 3.3 V operating-supply descriptions in distributor data. Its 32-LQFP 7 x 7 mm package provides 32 external pins for power, clock, communication, and general-purpose I/O connections. The device is suited to compact USB-connected peripherals, CAN-based industrial interfaces, low-cost control panels, sensor hubs, and embedded instrumentation. Its 48 MHz Cortex-M0 core is appropriate for interrupt-driven control, protocol handling, and application logic where a higher-performance Cortex-M3 or Cortex-M4 core is unnecessary. The 16 KB Flash capacity requires attention when selecting firmware size, boot code, and application-code partitioning. For PCB implementation, confirm the exact pin assignment and exposed functionality against the manufacturer datasheet before routing USB, CAN, crystal, reset, and supply connections. The provided search data does not include a complete electrical timing table, absolute maximum ratings, transceiver details, or a verified pin-by-pin description; those values require manufacturer documentation. The 32-LQFP package is suitable for automated assembly and is distinct from STM32F042K4U6, which uses a different package option. This page synthesizes verified distributor specifications, package information, pricing references, available cross-reference candidates, and practical sourcing considerations for engineers evaluating the STM32F042K4T6. Confirm current stock, lifecycle status, and manufacturer documentation before production release.

RFQ Contact
STM32F042K4U6 - 48MHz 16KB USB/CAN MCU | STMicroelectronics
STM32F042K4U6

STM32F042K4U6 - 48MHz 16KB USB/CAN MCU | STMicroelectronics

The STMicroelectronics STM32F042K4U6 is an ARM Cortex-M0 32-bit microcontroller operating at up to 48 MHz, with 16 KB of Flash memory, USB and CAN connectivity, and a 2.5 V or 3.3 V supply in a 32-pin UFQFPN package measuring 5 mm by 5 mm. Its combination of USB, CAN, compact packaging, and 48 MHz processing makes it suitable for connected control systems, USB-to-CAN bridges, compact human-interface devices, and industrial equipment requiring a low-footprint embedded controller. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The STM32F0 series belongs to the hierarchy of embedded microcontroller ICs, system-on-chip devices, and programmable control components. The STM32F042K4U6 uses the ARM Cortex-M0 RISC core, which executes 32-bit instructions while keeping the device suitable for cost-sensitive, low-power embedded designs. The STM32F042K4U6 combines a 48 MHz clock with 16 KB of programmable Flash for firmware. Its communication features include USB and CAN, while the 2.5 V or 3.3 V operating range supports common embedded supply rails. The 32-pin UFQFPN package has a 5 mm by 5 mm body, allowing the device to provide USB, CAN, and general-purpose control functions without requiring a larger high-pin-count package. The ARM Cortex-M0 architecture is designed around a compact instruction set and an interrupt-driven embedded-control model. Firmware can use the STM32 programming ecosystem and peripheral peripherals to manage USB device communication, CAN frames, timers, serial interfaces, and digital inputs and outputs. Exact RAM content, peripheral counts, GPIO count, and electrical limits must be confirmed in the manufacturer datasheet before finalizing the board design. Typical applications include USB-connected industrial accessories, CAN-based monitoring modules, compact data-acquisition controllers, USB-to-CAN interface equipment, and cost-sensitive embedded products. USB is useful for direct host connectivity, while CAN supports robust communication between distributed industrial nodes. The 48 MHz processing rate provides useful timing margin for protocol handling and control tasks in compact assemblies. PCB design should preserve the compact 5 mm by 5 mm footprint and route USB and CAN interfaces according to the manufacturer reference layout. Decoupling, grounding, exposed-pad thermal management, and signal-routing discipline are essential for reliable operation. Firmware and peripheral configurations should also be checked against the exact ordering code because similarly named STM32F0 devices can differ in memory and feature sets.

RFQ Contact
STM32F042K6T6 - 48MHz Cortex-M0 MCU 32KB Flash USB | STMicroelectronics
STM32F042K6T6

STM32F042K6T6 - 48MHz Cortex-M0 MCU 32KB Flash USB | STMicroelectronics

The STMicroelectronics STM32F042K6T6 is a 32-bit ARM Cortex-M0 microcontroller running at up to 48 MHz, integrating 32 KB of Flash memory and 6 KB of SRAM in a 32-pin LQFP (7x7 mm) package. It targets USB-enabled mainstream embedded designs requiring a low pin count, USB 2.0 Full-Speed Device with on-chip PHY, CAN 2.0B interface, and a rich set of peripherals including timers, ADC, comparators, and communication interfaces. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and peripheral interfaces. Within the broader taxonomy, the STM32F042K6T6 sits at the intersection of embedded processor -> ARM Cortex-M0 core -> 32-bit RISC MCU -> mainstream connectivity line MCU. The Cortex-M0 architecture uses the Thumb/Thumb-2 instruction set and is designed for deterministic, low-power real-time control, making the F042 series ideal for USB Type-C accessories, human-interface devices, and small-form-factor sensor nodes. Key features include 32 KB Flash with read-while-write support, 6 KB SRAM with hardware parity, a 12-bit 1 Msps ADC with up to 13 external channels, two 16-bit timers, one 32-bit timer, an independent watchdog, a real-time clock, and a USB 2.0 Full-Speed Device interface with integrated PHY that eliminates the need for an external USB transceiver. The device operates from 2.0V to 3.6V and supports both 2.5V and 3.3V application rails, with multiple low-power modes (Sleep, Stop, Standby) suited to battery-powered products. Architecturally, the STM32F042K6T6 leverages ST's 90 nm embedded Flash process and the Cortex-M0 v6-M core with single-cycle multiplier, achieving 0.93 DMIPS/MHz. The integrated 4-16 MHz HSI oscillator with PLL, plus a 32 kHz LSI for the RTC, allow bill-of-material reduction by removing the external crystal in non-USB applications. The CAN 2.0B interface, combined with USB, makes this part uniquely positioned among Cortex-M0 devices for industrial control and automotive body networks. Typical applications include USB HID peripherals (keyboards, mice, custom HID), USB-to-UART bridges, USB-C audio accessories, CAN node endpoints in industrial networks, small motor control boards, smart-home sensor hubs, and USB-charged IoT endpoints. The 32-pin LQFP footprint is breadboard-friendly and supports hand-rework prototypes while remaining suitable for high-volume SMT assembly. Design consideration: because USB DP/DM pins are bonded to specific GPIO pins (PA11/PA12), designers must avoid remapping these to alternate functions when the USB peripheral is enabled. The integrated pull-up resistor on the DP line is software-controlled, simplifying bus-powered designs. For CAN applications, an external transceiver (e.g., SN65HVD230) is still required because the F042 provides only the protocol controller. This page synthesizes distributor pricing, drop-in same-package alternatives, and design considerations not found in a single datasheet excerpt.

RFQ Contact
STM32F042K6U6 - 48MHz Cortex-M0 USB MCU | STMicroelectronics
STM32F042K6U6

STM32F042K6U6 - 48MHz Cortex-M0 USB MCU | STMicroelectronics

The STMicroelectronics STM32F042K6U6 is an ARM Cortex-M0 32-bit microcontroller operating at up to 48 MHz, with 32 KB of Flash memory and USB, CAN, and embedded-control peripherals, in a 32-pin UFQFPN package. The verified distributor listing identifies a 5x5 mm package and a 2.5 V/3.3 V supply class. This MCU belongs to the STM32F0 family and is positioned for compact embedded products requiring USB connectivity and a broad peripheral set. A microcontroller is an integrated circuit containing a processor core, memory, and peripherals on one device. The STM32F042K6U6 combines an ARM Cortex-M0 RISC core with embedded Flash and RAM resources, allowing a control system to execute firmware and interface with sensors, communications links, and actuators. In the hierarchy, it is a 32-bit microcontroller, embedded processor, semiconductor, and programmable control component. Verified features include a maximum 48 MHz operating frequency, 32 KB of Flash memory, USB, CAN, and an ARM Cortex-M0 CPU. The STMicroelectronics product page also describes high-speed embedded memory and the STM32F042x4/x6 device family. These features make the device relevant to USB-enabled human-interface equipment, industrial control nodes, communications modules, and low-cost embedded systems where a small package and integrated connectivity are useful. The U6 ordering code identifies the 32-pin UFQFPN option, while the exposed-pad package and tray presentation are reflected in the verified distributor data. The package is a surface-mount QFN-family component designed for PCB mounting. The exact RAM size, GPIO count, ADC resolution, supply limits, and pin names are not stated in the supplied verified data and must be confirmed from the manufacturer datasheet before design release. Typical design decisions include checking the USB clock configuration, CAN transceiver interface, bootloader workflow, and firmware peripheral mapping in the STM32CubeMX or equivalent STM32 toolchain. USB signal routing requires controlled impedance and careful placement of the USB data lines; CAN routing should account for transceiver requirements, termination, and protection. Designers should also confirm the exposed-pad thermal and assembly requirements from the manufacturer documentation. This product page consolidates the verified manufacturer identity, distributor specifications, package information, and sourcing context into one engineering reference. It does not substitute datasheet values that were not supplied in the verified web data. Confirm the official datasheet, errata, pinout, memory map, and electrical limits before PCB release or production qualification.

RFQ Contact
STM32F048G6U6 - 48MHz Cortex-M0 32KB MCU | STMicroelectronics
STM32F048G6U6

STM32F048G6U6 - 48MHz Cortex-M0 32KB MCU | STMicroelectronics

The STMicroelectronics STM32F048G6U6 is a 32-bit ARM Cortex-M0 microcontroller operating at up to 48 MHz, with 32 KB of Flash memory in a 28-pin UFQFPN 4 x 4 mm package. The device targets compact, low-voltage embedded systems that require efficient control processing without a high pin count. Its compact package and 48 MHz Cortex-M0 core make it suitable for compact consumer controls, sensing modules, industrial automation equipment and communication-oriented peripherals. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, peripherals and communication interfaces on one package. Within the embedded-system hierarchy, the STM32F048G6U6 is an ARM Cortex-M0 MCU, a 32-bit RISC microcontroller and a member of the STM32F0 product family. The Cortex-M0 architecture emphasizes low power consumption, simple instruction execution and deterministic behavior in cost-sensitive embedded control systems. The principal specifications are a maximum CPU frequency of 48 MHz, 32 KB of Flash program memory and a 28-UFQFPN package measuring 4 x 4 mm. The listing identifies the device as a low-voltage part operating from 1.8 V. Its 32-bit processing architecture provides more computational headroom than an 8- or 16-bit MCU while retaining the simple programming model associated with the Cortex-M0 core. The STM32F048G6U6 combines general-purpose embedded control with the peripheral integration expected from the STM32F0 family. Its small footprint reduces PCB area requirements, while the exposed-pad-style UFQFPN construction supports thermal dissipation when the operating conditions require it. Engineers should select input and output decoupling capacitors according to the manufacturer reference circuit and validate the power-management limits for the intended voltage and temperature range. Typical applications include compact motor-control modules, low-cost industrial sensors, programmable logic controllers, communication equipment and small consumer appliances. The 48 MHz clock rate is useful for protocol handling, digital control loops and coordinating multiple peripheral functions. The 32 KB Flash capacity is appropriate for compact firmware that includes application logic, boot handling, communications and configuration storage. A critical design consideration is the small 4 x 4 mm land pattern. Use the manufacturer pinout and footprint data to place all 28 package pins, connect the exposed thermal pad as directed and maintain adequate copper around the device for heat spreading. Confirm oscillator, debug, reset and communication connections against the application circuit before committing the PCB layout. This product page combines manufacturer and distributor specifications, a package-level alternative comparison and practical PCB guidance. It also distinguishes genuine same-package STM32 family options from broader cross-brand MCU choices, helping engineers evaluate replacement risk without treating every Cortex-M0 product as a direct substitute.

RFQ Contact
STM32F051C6T6 - 48MHz 32KB Cortex-M0 MCU | STMicroelectronics
STM32F051C6T6

STM32F051C6T6 - 48MHz 32KB Cortex-M0 MCU | STMicroelectronics

STMicroelectronics STM32F051C6T6 is an ARM Cortex-M0 32-bit RISC microcontroller operating at up to 48 MHz, with 32 KB of flash memory in a 48-LQFP package. The device operates from 2.0 V to 3.6 V and targets cost-sensitive embedded systems that require deterministic control, efficient peripheral integration, and compact package options. A microcontroller is a programmable semiconductor device that combines a processor core, program memory, data memory, and peripherals on one integrated circuit. The STM32F051 series belongs to the STM32F0 family, where the ARM Cortex-M0 core forms the foundation of a general-purpose embedded-control hierarchy spanning MCU, embedded processor, and semiconductor categories. The STM32F051C6T6 combines a 48 MHz maximum clock with 32 KB of flash for firmware storage. Its operating voltage range of 2.0 V to 3.6 V supports low-voltage embedded systems, while the 48-LQFP package exposes a broad set of I/O resources for control boards and compact automation equipment. The suffix T6 identifies an STMicroelectronics ordering configuration associated with the specified temperature and package options. At its core, the STM32F051C6T6 uses the 32-bit ARM Cortex-M0 RISC architecture, enabling efficient C-language firmware development with an ecosystem of general-purpose microcontrollers. The 32 KB flash configuration provides room for boot code, application logic, and configuration data in cost-sensitive designs. Exact RAM capacity, peripheral inventory, timer resources, and analog performance should be confirmed in the manufacturer datasheet before final design release. Typical uses include industrial control modules, compact sensor nodes, appliance controllers, building automation interfaces, and low-cost embedded instruments. In each application, the MCU can consolidate multiple control tasks into one device while operating from a 2.0 V to 3.6 V supply. Its 48 MHz Cortex-M0 processing capability is appropriate for digital control, communication handling, and peripheral coordination where a higher-performance Cortex-M core is unnecessary. PCB planning should follow the 48-LQFP land pattern and pin assignments defined by the manufacturer. Keep power and decoupling connections compact, provide clean grounding for digital and analog functions, and verify oscillator, reset, programming-interface, and I/O requirements against the device pin-description table. Adequate thermal copper and a stable 2.0 V to 3.6 V supply are essential for reliable operation. This page combines the core architecture, memory, voltage, package, and application characteristics of the STM32F051C6T6 with practical sourcing guidance, replacement considerations, and PCB design notes. These engineering details help teams assess MCU suitability before downloading the official documentation and committing the device to a production design.

RFQ Contact
STM32F051C6T7 - 48MHz ARM Cortex-M0 MCU, 32KB Flash | STMicroelectronics
STM32F051C6T7

STM32F051C6T7 - 48MHz ARM Cortex-M0 MCU, 32KB Flash | STMicroelectronics

The STMicroelectronics STM32F051C6T7 is an entry-level 32-bit ARM Cortex-M0 microcontroller in the STM32F0 Access Line, operating at up to 48 MHz with 32 KB of embedded Flash and 4 KB of SRAM. Housed in a 48-pin LQFP (7x7 mm) package, it operates from a 2.0 V to 3.6 V supply and integrates a high-performance RISC core with 1.25 DMIPS/MHz (0.9 DMIPS/MHz in Thumb mode) for deterministic embedded control. The -T7 industrial temperature grade spans -40 °C to +105 °C, while the part remains in active production on STMicroelectronics' mainstream MCU portfolio. An ARM Cortex-M0 microcontroller is a 32-bit RISC processor core implementing the ARMv6-M architecture, optimized for energy-efficient, deterministic real-time control. The Cortex-M0 belongs to the microcontroller (MCU) family within the broader taxonomy of microprocessors -> microcontrollers -> ARM Cortex-M series -> Cortex-M0. Cortex-M0 parts prioritize low cost, low power, and a Thumb-only instruction set, positioning the STM32F051C6T7 as a cost-down alternative to Cortex-M3/M4 parts where advanced DSP and floating-point are not required. Key features include up to 55 fast I/Os (5V-tolerant), an 11-channel 12-bit 1 µs ADC, one 12-bit DAC, two 16-bit timers, one 32-bit timer, an advanced-control PWM timer for motor control, two I²C, two SPI, one I²S, one HDMI-CEC, one USB 2.0 FS device (in companion STM32F052 variants, not on this 051C6), and a 4-channel DMA controller. A real-time clock (RTC), two watchdog timers, and a SysTick timer provide the timing backbone for safety-critical firmware. The integrated voltage regulator supports a low-power Sleep/Stop/Standby mode set with RTC retention. Architecturally, the device uses ST's 90 nm embedded Flash process and a bus matrix interconnecting the Cortex-M0 core, DMA, and the AHB/APB peripheral bridge. A single 8 MHz HSI oscillator (with 6-bit trim) plus a 40 kHz LSI and 4-32 MHz HSE crystal driver cover all common clocking topologies. The 12-bit ADC achieves 1 Msps with up to 19 multiplexed channels, and the 12-bit DAC supports buffered output for analog signal generation. Hardware CRC, a unique 96-bit device ID, and a JTAG/SWD debug port round out the on-chip resources. Typical applications include consumer electronics, motor control (small BLDC/PMSM with the advanced-control timer), USB HID peripherals (on 052x variants), home appliances, lighting, and low-cost IoT sensor nodes. The 48-pin LQFP footprint is friendly to 2-layer hobbyist PCBs and 4-layer industrial designs alike. When laying out the PCB, place a 100 nF decoupling capacitor within 2 mm of every VDD pin, keep the HSE crystal traces short, and provide a solid ground pour under the exposed-pad-adjacent pins to minimize EMI. Use SWD rather than JTAG to free up to 3 GPIOs for the application. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that complement (not duplicate) the ST datasheet. - The maximum ADC conversion rate is 1 Msps at 12-bit resolution (scaled down to 800 ksps at full Vdd range). - The advanced-control timer (TIM1) supports complementary PWM outputs with programmable dead-time insertion. - The LQFP-48 package has a JEDEC MSL-3 moisture sensitivity level and is Pb-free (RoHS compliant). - Programming/debug is supported via ST-LINK/V2-1, J-Link, and the on-chip ROM bootloader (USART1 boot pins).

RFQ Contact