Products (44,000+)

THS6182DW - Low-Power ADSL/PLC Line Driver | Texas Instruments
THS6182DW

THS6182DW - Low-Power ADSL/PLC Line Driver | Texas Instruments

The Texas Instruments THS6182DW is a low-power differential line driver designed for full-rate ADSL and power-line communication systems, with a 20-pin SOIC package. It uses current-feedback architecture, provides selectable operating-current modes, and supports an adjustable bias-current input. The device is specified for 1/0 DSL line-driving duties over a temperature range of -40°C to +85°C. An ADSL line driver is a specialized interface-circuit component that converts upstream data into a high-current differential signal suitable for transmission over copper telephone lines. This device belongs to the interface IC hierarchy: line driver → differential transceiver → communications interface → semiconductor. Unlike a general-purpose voltage-output amplifier, a current-feedback line driver combines high-frequency signal capability with output-current control designed specifically for line networks. Key operating features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer also identifies operation down to 1.8 mA per channel, an adjustable-current input, and a low-noise result of 3.2 nV/√Hz inverting current noise. These selectable modes allow designers to balance transmission performance against power dissipation. The current-feedback differential architecture supports full-rate ADSL applications while maintaining high linearity without the complexity and power burden of conventional designs. The adjustable bias input lets the circuit user control the operating-current condition, making it useful in designs where line length, transformer characteristics, aggregate line load, or central-office power density affect the preferred drive level. The THS6182 is also identified as pin-compatible with the EL1503C and EL1508C. Typical uses include ADSL central-office line-card equipment, DSL access concentrators, splitters, remote-terminal and line-unit equipment, and PLC interface circuits. The device is particularly relevant where multiple line channels share a constrained power budget, because its low-bias and shutdown modes reduce dissipation when channel activity is low or a port must be disabled. The primary design trade-off is current setting versus signal performance and power consumption. Select full-bias operation for maximum line drive, lower modes for reduced dissipation, and shutdown when the port is inactive. Place the device and its associated line-network components carefully because long high-current transmission paths can introduce impedance discontinuities and signal-integrity problems that are not corrected by changing bias mode. This product page combines the manufacturer’s functional description, operating-mode data, package information, interface use cases, and replacement guidance with practical selection notes. It also highlights the distinction between electrically equivalent order codes and genuinely pin-compatible drop-in choices, helping engineers assess whether a redesign or package-level substitution is actually required.

RFQ Contact
THS6212YS - Broadband PLC Line Driver | Texas Instruments
THS6212YS

THS6212YS - Broadband PLC Line Driver | Texas Instruments

Texas Instruments THS6212YS is a high-speed, differential broadband PLC/HPLC line-driver amplifier based on current-feedback architecture, with support for line power up to 14.5 dBm at frequencies through 30 MHz. The device is supplied in a 17-terminal, rectangular, no-lead die package. Its differential output topology is intended for power-line communication systems that require broadband signal transmission through challenging in-home or outdoor network wiring. A broadband PLC line driver is an interface amplifier that generates a differential signal for transmission over power-line communication wiring. The THS6212 belongs to the line-driver and receiver hierarchy of interface ICs, where its current-feedback amplifier architecture provides the active gain stage needed to drive external circuitry and realize a physical-layer transmitter signal. This makes it relevant to broadband PLC modems, HPLC endpoints, carrier communication equipment, and line-coupling networks. The manufacturer identifies current-feedback architecture, differential operation, transmission capability through 30 MHz, and line power up to 14.5 dBm as the principal characteristics of the THS6212. Differential drive helps reject common-mode disturbances picked up from the shared power-line environment. The broad operating bandwidth supports both low-frequency carrier data and substantially higher-frequency communication signals, while the 28 V maximum supply rating provides headroom for an industrial interface stage. The target is identified as an industrial-temperature device operating from -40 °C to +85 °C. Its 17-terminal no-lead package is intended for surface-mount assembly. Because this ordering code is associated with a die rather than a conventional leaded or molded IC package, PCB land-pattern design, exposed-pad treatment, assembly profile, and reflow requirements must be confirmed against the official package drawing before layout release. Typical uses include broadband PLC transmitters, HPLC communication endpoints, carrier-current networking equipment, and line-driver stages for communications over existing electrical infrastructure. In a transmitter implementation, the amplifier output is connected through the appropriate line-coupling and filtering network. Component values and protection requirements depend on the transformer, line impedance, conducted-emissions target, and safety arrangement of the complete communication equipment. Design should preserve the high-speed current-feedback path with short traces, carefully controlled return current, and decoupling placed close to the supply pins. Output isolation, impedance matching, and surge protection must be evaluated together because a line driver also sees the external network's distributed and transient behavior. The amplifier rating does not remove the need for application-level isolation and protection. This page consolidates the manufacturer's device description, electrical and environmental limits, sourcing structure, and engineering guidance. It also distinguishes verified device facts from parameters that require the official datasheet or package drawing, helping designers establish whether the THS6212YS fits a broadband PLC signal chain before committing the layout.

RFQ Contact
THS7303PW - 3-Channel Low-Power Video Amplifier | TI
THS7303PW

THS7303PW - 3-Channel Low-Power Video Amplifier | TI

The Texas Instruments THS7303PW is a three-channel, low-power video amplifier with I2C control, selectable filters, 6 dB gain, SAG correction, a 2:1 input multiplexer, and selectable input bias modes. It operates from a single 2.7 V to 5 V supply and is packaged in a 20-pin TSSOP (PW). The device also features a 190 MHz bandwidth and a 320 V/µs slew rate, making it suited to high-speed video signal processing. A video amplifier is an analog signal-conditioning IC that increases the amplitude and drive capability of composite, component, or other video signals. It belongs to the broader hierarchy of amplifier ICs, analog integrated circuits, and signal-chain semiconductors. The THS7303PW combines three buffered video channels with programmable control, allowing a compact design to select filtering, gain, multiplexer routing, and bias behavior without replacing multiple fixed-function devices. Its principal features include three integrated video amplifiers, a 2:1 input multiplexer, a selectable 6 dB gain setting, selectable low-pass filters, SAG correction, and an I2C interface. These functions support programmable video paths in set-top boxes, video processors, display equipment, surveillance systems, and general-purpose analog-to-digital signal-processing circuits. Low power consumption is particularly useful when three active video channels must operate continuously in compact commercial or industrial equipment. The THS7303PW uses a complementary silicon-germanium BiCom-III process according to the manufacturer documentation. Its approximately 190 MHz small-signal bandwidth and 320 V/µs slew rate provide ample speed for high-frequency video signals. The 2.1:1 power-supply current and 6 mA quiescent current reported in the device documentation describe a low-power design intended to balance drive strength, integration, and heat management in a surface-mount package. Typical uses include conditioning composite video for digitization, buffering multiple video outputs, switching between two input sources with a 2:1 multiplexer, and applying programmable filter or gain settings in display and broadcast equipment. The I2C control interface also enables software-controlled configuration of multiple channels in systems where the video path changes during operation. PCB design should preserve the short, controlled return paths needed by high-speed analog signals. Place input and output bypass capacitors close to the relevant supply and ground pins, keep video traces away from switching nodes and digital control lines, and follow the pin descriptions and layout guidance in the manufacturer datasheet. Bus pull-up resistors and series damping should be selected to keep SCL and SDA waveforms within valid limits. This page organizes the THS7303PW’s functions, pin-compatible replacement information, comparison parameters, application guidance, and practical design considerations. It supports faster component evaluation by placing the device’s key architectural features alongside the engineering checks required for reliable video-signal implementation.

RFQ Contact
THS7313PW - 3-Channel 6dB SDTV Video Amp | Texas Instruments
THS7313PW

THS7313PW - 3-Channel 6dB SDTV Video Amp | Texas Instruments

The Texas Instruments THS7313PW is a three-channel, low-power SDTV video amplifier with I2C control, selectable 6 dB gain, sag correction, 2:1 input multiplexing, and selectable input-bias modes. The device operates from a single 2.7 V to 5 V supply and is packaged in a 20-pin TSSOP (PW) package. It combines three video processing channels with digital configuration in one low-power integrated circuit. A video amplifier conditions analog composite video signals by providing gain, impedance buffering, bias control, and correction functions before the signal reaches an encoder, display interface, or video capture stage. The THS7313 belongs to the video-amplifier hierarchy within interface ICs and is intended for SDTV and related composite-video signal paths requiring controlled amplitude and multiple source selection. The principal features are three integrated video channels, 6 dB gain, 2:1 input multiplexing, sag correction, I2C-controlled configuration, and selectable input-bias modes. The 2:1 multiplexer allows each channel to select between two video inputs, reducing the number of external routing components when the source changes infrequently. I2C control supports programmable configuration while avoiding dedicated control pins for every parameter. The device is fabricated using Texas Instruments' complementary silicon-germanium BiCom-III process. This process supports the integration of high-speed analog video functions, low-power operation, and digital control in one monolithic device. Single-supply operation also simplifies PCB power planning in portable and space-constrained consumer equipment. Typical uses include SDTV set-top boxes, video scalers, digital video recorders, television sets, video game consoles, and other systems that process composite video. The three-channel architecture suits designs carrying red, green, and blue component signals or three separate composite-video channels. The integrated multiplexer is especially useful when each channel must accept one of two source signals. Designers should preserve the recommended input and output network, provide a stable low-noise supply, and verify I2C address and configuration settings before enabling signal routing. Because no complete pin-description table is reproduced here, use the manufacturer datasheet pin table and typical-application circuit when assigning tracks, terminating inputs, and placing bypass capacitors. This page consolidates the device identity, package information, verified commercial listing, candidate drop-in relationships, application guidance, and engineering considerations into a practical reference for evaluating the THS7313PW.

RFQ Contact
THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7314D

THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments

The Texas Instruments THS7314D is a 3-channel SDTV video amplifier with integrated fifth-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and combines three video channels in one package. According to the Texas Instruments product and data-sheet information, the device uses the Silicon-Germanium BiCom-III process and consumes 16 mA total quiescent current at 3.3 V. A video amplifier is an analog signal-chain component that conditions composite or component video signals between a source, processing stage, and display. It belongs to the amplifier hierarchy, specifically the video-amplifier and video-buffer category. Unlike a passive termination network, an integrated video amplifier can provide filtering, gain, impedance matching, and output-drive capability while reducing the number of discrete components required on a video board. The THS7314D provides three buffered channels, 6 dB gain, and fifth-order filtering in one 8-pin SOIC. Its rail-to-rail output stage supports both AC and DC line-driving requirements. The manufacturer specifically identifies driving two lines or 75-ohm loads as supported use cases, making the device relevant to SDTV routing, video distribution, and display-adapter designs. The integrated filter function is especially useful when system designers want repeatable channel filtering without external filter networks. Its low-power operation distinguishes the part from higher-current video drivers. Texas Instruments states that the total 16 mA quiescent current at a 3.3 V supply makes the THS7314 suitable for USB-powered, portable, and other power-sensitive video applications. The single-supply 3 V to 5 V operating range also allows the same architecture to operate from nominal 3.3 V and 5 V system rails, although the complete design must satisfy the limits in the manufacturer data sheet for each voltage and temperature condition. Typical applications include SDTV output buffering, video splitters and distribution boards, portable media equipment, video capture equipment, and display interfaces. In each case, the three-channel structure reduces routing complexity while the fifth-order filters and 6 dB gain support controlled signal transmission into downstream analog video stages. The 75-ohm drive capability is useful when the output must connect through conventional video cabling to a terminated load. Designers should verify the complete pin configuration, decoupling requirements, input and output impedance, bandwidth, channel-to-channel behavior, and recommended termination network against the official data sheet. Video-layout practices should also be considered, including short trace routing, careful grounding, separation between analog video paths and noisy switching circuitry, and appropriate filtering at external connectors. This page consolidates the verified manufacturer and distributor information for THS7314D and clearly identifies parameters for which verified values were not supplied. It also distinguishes the confirmed device characteristics from engineering information that must be obtained from the official THS7314 data sheet before layout or qualification decisions are finalized.

RFQ Contact
THS7314DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7314DR

THS7314DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments THS7314DR is a 3-channel SDTV video amplifier with integrated fifth-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and combines three video channels in one package. According to the Texas Instruments product and data-sheet information, the device uses the Silicon-Germanium BiCom-III process and consumes 16 mA total quiescent current at 3.3 V. A video amplifier is an analog signal-chain component that conditions composite or component video signals between a source, processing stage, and display. It belongs to the amplifier hierarchy, specifically the video-amplifier and video-buffer category. Unlike a passive termination network, an integrated video amplifier can provide filtering, gain, impedance matching, and output-drive capability while reducing the number of discrete components required on a video board. The THS7314DR provides three buffered channels, 6 dB gain, and fifth-order filtering in one 8-pin SOIC. Its rail-to-rail output stage supports both AC and DC line-driving requirements. The manufacturer specifically identifies driving two lines or 75-ohm loads as supported use cases, making the device relevant to SDTV routing, video distribution, and display-adapter designs. The integrated filter function is especially useful when system designers want repeatable channel filtering without external filter networks. Its low-power operation distinguishes the part from higher-current video drivers. Texas Instruments states that the total 16 mA quiescent current at a 3.3 V supply makes the THS7314 suitable for USB-powered, portable, and other power-sensitive video applications. The single-supply 3 V to 5 V operating range also allows the same architecture to operate from nominal 3.3 V and 5 V system rails, although the complete design must satisfy the limits in the manufacturer data sheet for each voltage and temperature condition. Typical applications include SDTV output buffering, video splitters and distribution boards, portable media equipment, video capture equipment, and display interfaces. In each case, the three-channel structure reduces routing complexity while the fifth-order filters and 6 dB gain support controlled signal transmission into downstream analog video stages. The 75-ohm drive capability is useful when the output must connect through conventional video cabling to a terminated load. Designers should verify the complete pin configuration, decoupling requirements, input and output impedance, bandwidth, channel-to-channel behavior, and recommended termination network against the official data sheet. Video-layout practices should also be considered, including short trace routing, careful grounding, separation between analog video paths and noisy switching circuitry, and appropriate filtering at external connectors. This page consolidates the verified manufacturer and distributor information for THS7314DR and clearly identifies parameters for which verified values were not supplied. It also distinguishes the confirmed device characteristics from engineering information that must be obtained from the official THS7314 data sheet before layout or qualification decisions are finalized.

RFQ Contact
THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7315D

THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments

Texas Instruments THS7315D is a three-channel SDTV video amplifier with integrated fifth-order filters and 5.2 V/V gain, operating from a single 3 V to 5 V supply in an 8-SOIC package. The device combines three video channels, fixed 5.2 V/V gain, and fifth-order filtering for CVBS, S-Video, YPBPR 480i/576i, YUV, and GBR/RGB signal paths. A video amplifier is an analog signal-conditioning IC that increases the amplitude of composite or component video signals while controlling bandwidth, attenuation, and unwanted spectral content. Within the broader semiconductor hierarchy, the THS7315D is a video amplifier, a type of analog amplifier, and ultimately an integrated circuit used within display, broadcast, set-top-box, and video-conversion systems. The THS7315D integrates three independent SDTV video amplifier channels and fifth-order filters into one package. Its fixed gain of 5.2 V/V is useful when a source produces a relatively small video amplitude and the downstream circuitry requires additional signal swing. The fifth-order filters provide frequency-dependent noise and interference attenuation, while the single-supply architecture simplifies power planning in 3 V and 5 V systems. Texas Instruments fabricated the device using its complementary silicon-germanium BiCom3 process. This integration reduces the number of discrete amplification and filtering stages required in a multi-channel analog video path. Because the amplifier includes filters rather than functioning only as a wideband buffer, board-level signal integrity depends on correct source and load impedances, adequate bypass capacitance, short output routing, and proper grounding. The supplied data does not provide detailed output impedance, bandwidth, settling-time, noise, or stability-versus-capacitance figures, so those characteristics must be confirmed in the manufacturer datasheet before final circuit sign-off. Typical uses include SDTV video buffering, Y/Cb/Cr component-video distribution, CVBS and S-Video processing, RGB amplification, and DAC reconstruction filtering. The integrated three-channel arrangement is particularly useful when red, green, and blue or Y, Pb, and Pr channels must receive matched amplification and filtering. It can also support protected or industrial video equipment where reducing the number of active stages simplifies signal routing and maintenance. A primary design consideration is ensuring that the source impedance, termination, and downstream load remain compatible with the integrated filter network. The manufacturer's datasheet and typical application information should be used to select input and output coupling or termination components. PCB layout should keep the device and its bypass capacitors close together, maintain short analog traces, provide an uninterrupted ground reference, and isolate sensitive video paths from switching and high-current return paths. This product page consolidates the verified manufacturer and distributor information, distinguishes documented THS7315D characteristics from missing technical data, identifies verified same-package replacements, and adds practical application and layout guidance for engineers evaluating the THS7315D in SDTV video signal chains.

RFQ Contact
THS7315DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7315DR

THS7315DR - 3-Channel SDTV Video Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments THS7315DR is a three-channel SDTV video amplifier with integrated fifth-order filters and 5.2 V/V gain, operating from a single 3 V to 5 V supply in an 8-SOIC package. The device combines three video channels, fixed 5.2 V/V gain, and fifth-order filtering for CVBS, S-Video, YPBPR 480i/576i, YUV, and GBR/RGB signal paths. A video amplifier is an analog signal-conditioning IC that increases the amplitude of composite or component video signals while controlling bandwidth, attenuation, and unwanted spectral content. Within the broader semiconductor hierarchy, the THS7315DR is a video amplifier, a type of analog amplifier, and ultimately an integrated circuit used within display, broadcast, set-top-box, and video-conversion systems. The THS7315DR integrates three independent SDTV video amplifier channels and fifth-order filters into one package. Its fixed gain of 5.2 V/V is useful when a source produces a relatively small video amplitude and the downstream circuitry requires additional signal swing. The fifth-order filters provide frequency-dependent noise and interference attenuation, while the single-supply architecture simplifies power planning in 3 V and 5 V systems. Texas Instruments fabricated the device using its complementary silicon-germanium BiCom3 process. This integration reduces the number of discrete amplification and filtering stages required in a multi-channel analog video path. Because the amplifier includes filters rather than functioning only as a wideband buffer, board-level signal integrity depends on correct source and load impedances, adequate bypass capacitance, short output routing, and proper grounding. The supplied data does not provide detailed output impedance, bandwidth, settling-time, noise, or stability-versus-capacitance figures, so those characteristics must be confirmed in the manufacturer datasheet before final circuit sign-off. Typical uses include SDTV video buffering, Y/Cb/Cr component-video distribution, CVBS and S-Video processing, RGB amplification, and DAC reconstruction filtering. The integrated three-channel arrangement is particularly useful when red, green, and blue or Y, Pb, and Pr channels must receive matched amplification and filtering. It can also support protected or industrial video equipment where reducing the number of active stages simplifies signal routing and maintenance. A primary design consideration is ensuring that the source impedance, termination, and downstream load remain compatible with the integrated filter network. The manufacturer's datasheet and typical application information should be used to select input and output coupling or termination components. PCB layout should keep the device and its bypass capacitors close together, maintain short analog traces, provide an uninterrupted ground reference, and isolate sensitive video paths from switching and high-current return paths. This product page consolidates the verified manufacturer and distributor information, distinguishes documented THS7315DR characteristics from missing technical data, identifies verified same-package replacements, and adds practical application and layout guidance for engineers evaluating the THS7315DR in SDTV video signal chains.

RFQ Contact
THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments
THS7316D

THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments

Texas Instruments THS7316D is a 3-channel HDTV video amplifier with integrated 5th-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and provides three buffered video channels for HDTV and related video-signal processing systems. The device is fabricated using the Silicon-Germanium (SiGe) BiCom-III process and is designed for low-power video applications where integrated filtering reduces external circuit complexity. A video amplifier is a specialized analog amplifier that buffers and conditions composite or component video signals while preserving usable bandwidth and signal amplitude. The THS7316 belongs to the broader video-amplifier and signal-conditioning category, integrating three amplifier channels with fixed filtering into one device. This makes it useful in set-top boxes, television equipment, video processors, projectors, displays, and other systems that distribute or convert analog video signals. The principal features of the THS7316D are its three-channel architecture, 6 dB voltage gain, 5th-order integrated filters, single-supply operation, and 43 MHz video bandwidth identified in the verified product data. The filter implementation helps remove unwanted high-frequency video components before they reach downstream circuitry. Its three-channel arrangement allows red, green, and blue video paths to be amplified consistently within one package, reducing the number of separate buffer devices required. The device uses a low-power SiGe BiCom-III process and is intended for 3 V to 5 V single-supply systems. The verified distributor description identifies the THS7316 as a 3-channel integrated video buffer, while the Texas Instruments product page identifies the 5th-order filter and 6 dB gain functions. The 8-SOIC package is compatible with conventional surface-mount assembly and is suitable for compact consumer and industrial video equipment. Typical applications include HDTV signal conditioning, RGB video distribution, video projection systems, television receivers, set-top-box video outputs, and industrial video interfaces. The integrated filtering is particularly useful where the source signal requires predictable bandwidth limiting before a display, encoder, scaler, or analog-to-digital conversion stage. The fixed 6 dB gain also provides a defined signal-conditioning function rather than requiring an external gain network for basic video buffering. Designers should verify the complete electrical limits, decoupling requirements, output loading, and filter response in the manufacturer datasheet before layout release. Pay particular attention to the single-supply input range, required bypass capacitors, and the acceptable input and output signal levels. Because the available verified data does not provide the complete pin mapping or all parameter values, the PCB footprint and analog signal path should be checked against the official THS7316 documentation rather than inferred from distributor descriptions. This page combines verified manufacturer and distributor information, source-backed technical context, and practical selection considerations for engineers evaluating the THS7316D. It also distinguishes verified attributes from parameters that remain to be confirmed in the datasheet, helping prevent assumptions about gain, bandwidth, filtering, or pin compatibility during component selection.

RFQ Contact
THS7316DR - 3-Channel HDTV Video Amplifier | Texas Instruments (Tape & Reel)
THS7316DR

THS7316DR - 3-Channel HDTV Video Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments THS7316DR is a 3-channel HDTV video amplifier with integrated 5th-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and provides three buffered video channels for HDTV and related video-signal processing systems. The device is fabricated using the Silicon-Germanium (SiGe) BiCom-III process and is designed for low-power video applications where integrated filtering reduces external circuit complexity. A video amplifier is a specialized analog amplifier that buffers and conditions composite or component video signals while preserving usable bandwidth and signal amplitude. The THS7316 belongs to the broader video-amplifier and signal-conditioning category, integrating three amplifier channels with fixed filtering into one device. This makes it useful in set-top boxes, television equipment, video processors, projectors, displays, and other systems that distribute or convert analog video signals. The principal features of the THS7316DR are its three-channel architecture, 6 dB voltage gain, 5th-order integrated filters, single-supply operation, and 43 MHz video bandwidth identified in the verified product data. The filter implementation helps remove unwanted high-frequency video components before they reach downstream circuitry. Its three-channel arrangement allows red, green, and blue video paths to be amplified consistently within one package, reducing the number of separate buffer devices required. The device uses a low-power SiGe BiCom-III process and is intended for 3 V to 5 V single-supply systems. The verified distributor description identifies the THS7316 as a 3-channel integrated video buffer, while the Texas Instruments product page identifies the 5th-order filter and 6 dB gain functions. The 8-SOIC package is compatible with conventional surface-mount assembly and is suitable for compact consumer and industrial video equipment. Typical applications include HDTV signal conditioning, RGB video distribution, video projection systems, television receivers, set-top-box video outputs, and industrial video interfaces. The integrated filtering is particularly useful where the source signal requires predictable bandwidth limiting before a display, encoder, scaler, or analog-to-digital conversion stage. The fixed 6 dB gain also provides a defined signal-conditioning function rather than requiring an external gain network for basic video buffering. Designers should verify the complete electrical limits, decoupling requirements, output loading, and filter response in the manufacturer datasheet before layout release. Pay particular attention to the single-supply input range, required bypass capacitors, and the acceptable input and output signal levels. Because the available verified data does not provide the complete pin mapping or all parameter values, the PCB footprint and analog signal path should be checked against the official THS7316 documentation rather than inferred from distributor descriptions. This page combines verified manufacturer and distributor information, source-backed technical context, and practical selection considerations for engineers evaluating the THS7316DR. It also distinguishes verified attributes from parameters that remain to be confirmed in the datasheet, helping prevent assumptions about gain, bandwidth, filtering, or pin compatibility during component selection.

RFQ Contact
THS7353PW - 3-Channel I2C Video Amp | Texas Instruments
THS7353PW

THS7353PW - 3-Channel I2C Video Amp | Texas Instruments

Texas Instruments THS7353PW is a three-channel, low-power video amplifier with I2C control, selectable filters, 0 dB gain, and a 2:1 input multiplexer in a 20-pin TSSOP (PW) package. It operates from a single 2.7 V to 5 V supply and consumes 16.2 mA total quiescent current at a 3.3 V supply. A video amplifier, also called a video buffer, conditions analog video signals between source and destination stages. The THS7353 belongs to the broader integrated video-amplifier hierarchy, combining signal buffering, gain control, filtering, input selection, and serial configuration in one semiconductor. This integration reduces the number of discrete signal-path components while allowing programmable behavior through an I2C interface. The device provides three video channels, a selectable 2:1 multiplexer, selectable low-pass or bypass filter configurations, and programmable 0 dB gain. Its low-power design and single-supply operation suit portable equipment, including USB-powered systems, as well as HDTV, PVR, DVDR, projector, and general-purpose video equipment. An operating-temperature range of -40 °C to +85 °C supports industrial and commercial environments. The THS7353 is fabricated using Texas Instruments' complementary silicon-germanium BiCom-III process. This process supports the integration of three video channels, filtering functions, multiplexing, gain control, and digital control into a compact low-power device. The 20-TSSOP package supports surface-mount PCB assembly while providing separate routing flexibility for three video channels. Typical deployments include buffering component video and computer video outputs, switching between two video sources through the 2:1 multiplexer, filtering unwanted video-frequency content, and protecting source devices from downstream loading. Portable and projector designs benefit from the 2.7 V minimum supply and 16.2 mA quiescent current at 3.3 V, although system-level power depends on the selected configuration and output loading. Design the I2C address and control register settings before laying out the PCB, and confirm compatibility with the video timing and filter requirements of the target source. Decoupling and analog return paths should be arranged to minimize switching noise and ground potential differences between the amplifier and video source. This product page combines manufacturer specifications, application guidance, candidate replacement analysis, and practical PCB considerations. It identifies where THS7353PW fits, which published alternatives remain unverified as true pin-to-pin replacements, and which design parameters should be checked before approving a substitution.

RFQ Contact
THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments
THS7375

THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments

The THS7375 is a low-power, single-supply, 3 V to 5 V four-channel integrated video buffer from Texas Instruments, fabricated using the complementary Silicon-Germanium (SiGe) BiCom3X process. It is available in a lead-free and green (RoHS) compliant TSSOP-14 package. The device incorporates a sixth-order Butterworth filter that can be bypassed, making it useful as a digital-to-analog converter (DAC) reconstruction filter. With a rail-to-rail output stage and a fixed gain of 5.6 V/V (15 dB), the THS7375 is designed for SDTV video applications, providing excellent image quality and driving capability for both AC and DC coupled loads. A video amplifier is an electronic amplifier that processes video signals, typically providing gain, buffering, and filtering to ensure signal integrity over transmission lines. In the signal chain, the THS7375 sits between a video DAC or encoder and the output connector, performing reconstruction filtering and line driving. It belongs to the category of integrated video buffers, which are essential in consumer electronics, set-top boxes, DVD players, and video surveillance systems. The THS7375's integrated filters eliminate the need for external passive components, simplifying design and reducing board space. Key features include a 6th-order Butterworth filter with a cutoff frequency suitable for SDTV (standard-definition television) signals, a fixed gain of 5.6 V/V, and the ability to drive two lines per channel or 75-ohm loads. The device operates from a single 3 V to 5 V supply, making it compatible with common digital logic levels. The rail-to-rail output stage ensures maximum output swing, and the low power consumption makes it ideal for battery-powered or power-sensitive applications. Technically, the THS7375 uses the BiCom3X process, which combines bipolar and CMOS transistors on a silicon-germanium substrate, offering high-speed performance with low power. The integrated filter is a 6th-order Butterworth type, providing a flat passband and sharp roll-off to remove out-of-band noise and aliasing artifacts. The device also features an internal gain of 5.6 V/V, which is optimized for driving video loads with proper termination. Typical applications include video buffer and line driver for SDTV signals in set-top boxes, DVD players, video recorders, and surveillance systems. It is also suitable for driving video signals from DaVinci processors and other video encoders. The THS7375's ability to drive two lines per channel allows for flexible routing in complex video distribution systems. When designing with the THS7375, ensure proper power supply decoupling with a 0.1 uF ceramic capacitor close to the VCC pin. The input should be AC-coupled if the source has a DC offset, and the output should be terminated with 75-ohm resistors to match the characteristic impedance of the cable. The filter bypass pin can be used to disable the internal filter if external filtering is preferred.

RFQ Contact
THS788PFD - 200 MHz Quad-Channel 13 ps TMU | Texas Instruments
THS788PFD

THS788PFD - 200 MHz Quad-Channel 13 ps TMU | Texas Instruments

The Texas Instruments THS788PFD is a four-channel time measurement unit (TMU) using time-to-digital converter architecture, with 8 ps single-shot accuracy, 13 ps resolution derived from an external 200 MHz controller clock, and a measurement result range of 7 s in a 100-pin HTQFP package. It supports a 200 MHz event-input rate and provides LVDS-compatible event inputs, an LVDS result interface, four event channels, and a synchronization channel. A time measurement unit is a specialized clock-and-timing semiconductor that converts the elapsed time between events into a digital result. The THS788 belongs to the TMU hierarchy, where its TDC architecture combines fine timing resolution with high-rate event capture. This makes it suitable for systems requiring precise timing rather than ordinary counting, including synchronized instrumentation, pulsed systems, test equipment, and communications or industrial timing subsystems. The key performance feature is 8 ps single-shot accuracy, supported by a 13 ps least-significant-bit resolution. The external controller clock operates at 200 MHz, and the event input rate can reach 200 MHz. The 7 s result range supports substantially longer measurement intervals than the 13 ps conversion resolution alone would imply, depending on the configured measurement sequence and system implementation. LVDS-compatible interfaces provide high-speed, noise-resistant signaling for demanding board environments. Technically, the THS788 uses a fast TDC architecture to perform time measurements across four event channels. Its inputs are designed for LVCMOS or LVDS signaling, while the result output is identified as LVDS. The synchronized architecture and dedicated sync channel make the device suitable for multi-event acquisition where repeatable timing relationships matter. The stated low temperature coefficient of 0.1 ps/°C indicates attention to timing stability over temperature. Typical applications include high-speed test and measurement systems, pulsed-signal analysis, synchronization of multiple timing events, industrial automation requiring deterministic event capture, and communications equipment that must measure narrow time intervals. The device can also support scientific instrumentation where event timing accuracy directly affects the quality of the collected result. Designers should treat the external 200 MHz clock, LVDS-compatible input routing, result interface, decoupling, and high-speed return paths as an integrated signal-integrity problem. Input timing, trace length, termination, and controller configuration must be evaluated together because the 13 ps resolution does not guarantee end-to-end system accuracy without clean clocking, controlled stimulus, and correct interface implementation. This page combines the verified manufacturer and distributor information for the THS788PFD with practical selection guidance, application analysis, pricing references, and an honest assessment of available drop-in alternatives.

RFQ Contact
THS788PFDT - 200MHz 4-Channel 8ps Timing IC | Texas Instruments
THS788PFDT

THS788PFDT - 200MHz 4-Channel 8ps Timing IC | Texas Instruments

The Texas Instruments THS788PFDT is a four-channel time measurement unit (TMU) built around a time-to-digital converter architecture, with 8 ps single-shot accuracy, 13 ps resolution derived from a 200 MHz external controller clock, and fast LVDS-compatible event inputs. The device is packaged in a 100-terminal 14 x 14 mm HTQFP surface-mount package and is intended for precision time-interval measurement applications. A time measurement unit is a specialized timing IC that converts the arrival time of an event into a digital value relative to a synchronization reference. The THS788 places a time-to-digital converter inside each measurement channel, allowing timing information to be captured with picosecond-class resolution instead of relying on a general-purpose counter clock. Its hierarchy runs from time measurement unit to time-to-digital converter, then to application-specific clock and timing IC and semiconductor. Key features include four measurement channels, 8 ps single-shot accuracy, 13 ps time-to-digital-converter resolution, and LVDS-compatible event inputs. The 200 MHz master clock determines the nominal TDC timing resolution, while a sync-channel input establishes time zero. According to the manufacturer product page, the device uses fast LVDS-compatible interfaces for its event inputs and supports calibrated timing calculations relative to the synchronization reference. The device supports fast event capture through hit latches, which latch an event edge before the timing data is processed. This architecture is useful when several channels must respond to closely spaced signals and the relative delay between them must be measured reliably. The controller interface and external clock remain essential parts of the measurement system because synchronization, calibration, and digital result transfer determine the integrity of the captured timing data. Typical applications include pulsed-laser range measurement, optical communication timing, radar and test instrumentation, high-speed trigger correlation, and industrial diagnostics that compare an event against a periodic reference. In such systems, the sync channel defines time zero, each event input records its relative arrival time, and the external controller applies calibration values before reporting the result. A critical design consideration is preserving the integrity of the 200 MHz reference clock and the LVDS-compatible event signals. Route timing-sensitive inputs as controlled-impedance nets, keep the clock away from high-current switching nodes, and use the exposed-pad land pattern and thermal vias recommended in the package drawing. Differential timing measurements are only as accurate as the reference distribution and input return-loss behavior of the complete board. This page consolidates the manufacturer timing specifications, package details, sourcing channels, and engineering guidance for the THS788PFDT, adding pin-connection and thermal-placement guidance that engineers would otherwise have to derive across multiple technical documents.

RFQ Contact
THS789PFD - Quad-Channel 200MHz Time Measurement IC | TI
THS789PFD

THS789PFD - Quad-Channel 200MHz Time Measurement IC | TI

Texas Instruments THS789PFD is a quad-channel time measurement unit (TMU) with a 200 MHz measurement clock, one output, and a 100-pin HTQFP package measuring 14 mm by 14 mm. The device is listed for commercial-grade operation from 0 °C to 70 °C and is supplied in a tray. Its verified product identity also includes an exposed thermal pad and surface-mount construction. A time measurement unit is a specialized clock-and-timing semiconductor that measures elapsed time by comparing reference events. A multi-channel TMU extends this function across several independent measurement paths, making it useful when a system must acquire timing relationships, delays, pulse widths, or event intervals without implementing each measurement function as discrete logic. The THS789 therefore belongs to the clock-and-timing IC category and the broader application-specific timing semiconductor hierarchy. The principal verified specifications are four measurement channels, a 200 MHz timing reference, and one output. The 200 MHz reference corresponds to a 5 ns reference period, while the quad-channel architecture permits parallel timing observations. The 100-pin HTQFP package provides numerous external connections for timing inputs, control, power, and outputs, while the exposed pad supports heat transfer from the device to the PCB. The THS789PFD is specifically identified as a Time Measurement IC and is marketed by DigiKey under the Application Specific Clock/Timing classification. This distinguishes it from conventional general-purpose timers by emphasizing precision event-interval measurement across four channels. The exact input voltage range, minimum measurable interval, timing accuracy, propagation delay, output characteristics, and power specifications are not included in the supplied verified excerpts and should be taken from the complete manufacturer datasheet before design release. Typical engineering uses include industrial automation equipment, communications timing analysis, instrumentation, automated test systems, and embedded systems that compare multiple event arrivals. The 100-pin package and exposed pad make careful PCB layout, grounding, and thermal management important. In multi-channel systems, signal integrity at the timing inputs can materially affect measurement consistency, so controlled impedance, short return paths, and clean reference distribution should be prioritized. A principal design trade-off is package size versus channel density: the 14 mm by 14 mm HTQFP offers extensive connectivity for four timing channels but requires more PCB area than a compact mixed-signal package. Engineers should also confirm the complete electrical limits and interface timing before substituting another device or extending the operating temperature beyond the verified 0 °C to 70 °C range. This product record combines verified manufacturer and distributor identity, package and ordering information, commercial availability, and explicit engineering guidance for evaluating the THS789PFD. It also distinguishes confirmed facts from parameters that still require review in the full Texas Instruments datasheet, supporting faster procurement and design planning without treating unverified specifications as guaranteed.

RFQ Contact
THS8135PHP - 10-Bit Triple 240-MSPS Video DAC | TI
THS8135PHP

THS8135PHP - 10-Bit Triple 240-MSPS Video DAC | TI

The Texas Instruments THS8135PHP is a triple 10-bit video digital-to-analog converter optimized for video and graphics applications, with a maximum sampling rate of 240 MSPS in a 48-lead HTQFP package measuring 7 mm by 7 mm. It operates from a 3.3 V analog supply and a 1.8 V digital supply, separating sensitive analog signaling from lower-voltage digital control and data inputs. A DAC is a data converter that translates digital codes into proportional analog voltages or currents. Video DACs belong to the broader ADC/DAC and data-converter IC hierarchy, where they sit between parallel digital pixel data and analog signals used by display or video-processing circuitry. The THS8135PHP combines three converters with circuitry for bi-level or tri-level synchronization and blanking-level generation. The principal features of this device are its three independent 10-bit conversion channels, 240 MSPS performance, parallel digital interface, and dedicated analog and digital supply rails. Each converter resolves the video signal into 10-bit steps. The parallel interface supports direct connection to video data sources without requiring a serial interface or a separate high-speed communication protocol. The package also provides a consolidated implementation for three color channels rather than requiring three separate DAC packages. The architecture is tailored to conventional component and graphics video systems. ITU-R BT.601-compatible full-scale output is identified for this device, making its output scaling suitable for standard-definition digital-video workflows. Bi-level and tri-level sync generation can produce the blanking levels required when converting active digital video into analog composite video. The 3.3 V analog rail and 1.8 V digital rail support partitioned supply planning, although both rails and the interface still require careful decoupling. Typical applications include SD and other video graphics systems, test and measurement video generation, digital signage, display-processing boards, and industrial imaging panels. The device is particularly useful when three synchronized analog outputs are required and the source interface already provides parallel pixel data. Its 240 MSPS ceiling provides substantial timing margin for common progressive video rates. PCB design should keep analog and digital return currents separated, place supply capacitors close to their corresponding pins, and route the parallel data bus with matched-length practices where timing margin is limited. The 48-lead HTQFP also requires careful thermal design because sustained high update rates can increase package dissipation. Use the manufacturer's pin-description table when assigning every power, data, clock, sync, and output connection. This page combines the device's principal conversion specifications, application guidance, package details, and engineering-focused replacement considerations. It also organizes sourcing information and drop-in comparison points into a format intended to accelerate schematic review, footprint verification, and prototype planning.

RFQ Contact
THS8136PHP - Triple 10-Bit 180-MSPS Video DAC | Texas Instruments
THS8136PHP

THS8136PHP - Triple 10-Bit 180-MSPS Video DAC | Texas Instruments

The Texas Instruments THS8136PHP is a triple 10-bit, 180-MSPS graphics and video digital-to-analog converter in a 48-pin HTQFP package measuring 7 mm by 7 mm. It operates from a 3.3 V analog supply and a 1.8 V digital supply, integrating three parallel-input DAC channels with circuitry for bi-level sync and blanking-level generation. The converter is designed for video and graphics systems that require simultaneous red, green, and blue analog outputs. A DAC is a data converter that translates digital color or graphics codes into proportional analog voltages. The THS8136 belongs to the video DAC category, a specialized form of digital-to-analog converter used to drive analog display and video-processing equipment. Its parallel interface, triple-channel architecture, and integrated sync and blanking support place it within high-speed video signal-chain components rather than general-purpose precision DACs. The device provides three 10-bit DAC channels operating at sampling rates up to 180 MHz. Its 1.8 V digital supply supports modern digital graphics logic, while the 3.3 V analog supply provides the operating rail for the output converters. A common full-scale-adjustment resistor sets the output range of all three channels, and a 3.8-kilohm resistor is suitable for systems targeting approximately 700 mV full-scale output levels. The 0.015-microsecond settling time supports high-speed pixel and video timing requirements. Internal circuitry generates bi-level synchronization and blanking levels for RGB and YPbPr color spaces. These functions reduce the amount of external glue logic needed when generating composite or component video signals. The parallel digital inputs accept sampled video data, while the three analog outputs provide independent red, green, and blue channels. This integration makes the THS8136 useful in graphics controllers, video splitters, frame buffers, digital display systems, and test equipment. A typical implementation places the three DAC outputs on controlled impedance PCB traces and connects the digital input bus to the graphics or video source. Designers should terminate and route the high-speed digital interface carefully because edge-rate harmonics can radiate even though the maximum sampling rate is 180 MHz. Analog and digital return currents should be managed so switching activity does not disturb the output reference. The principal design trade-off is integration versus operating flexibility. The THS8136PHP combines three converters and video-control functions in one package, reducing external circuitry, but its dedicated video feature set makes it less suitable than a general-purpose DAC when arbitrary analog waveforms, calibration, or multiple independent output ranges are required. Confirm package pin assignments and exposed-pad requirements in the manufacturer datasheet before layout release. This product overview combines the manufacturer’s device description with package, interface, output-adjustment, and ordering details that help engineers assess the THS8136PHP before designing a video DAC signal chain. It also clarifies the distinctions among same-device ordering options and pin-compatible industrial-grade variants.

RFQ Contact
THS8200PFP - Triple 10-Bit Video DAC | Texas Instruments
THS8200PFP

THS8200PFP - Triple 10-Bit Video DAC | Texas Instruments

Texas Instruments THS8200PFP is a triple 10-bit all-format video digital-to-analog converter in an 80-pin HTQFP (PFP) package measuring 12 x 12 mm. It converts digital component-video signals into three analog video outputs and supports 4:4:4 and 4:2:2 input formats through three, two, or one 10-bit ports. The specified operating-temperature range is 0°C to 70°C. A video DAC is the output stage of a digital video system. It belongs to the DAC and ADC/DAC hierarchy, which converts digital data into analog voltage signals for downstream displays, video processors, transmission equipment, or recording systems. For the THS8200PFP, the defining system role is the simultaneous generation of three analog video channels from component-video data while accepting multiple digital-interface configurations. Key features include three integrated 10-bit DAC channels, support for all-format component-video conversion, serial digital input, and a high-pin-count HTQFP package. The three 10-bit ports give the system designer flexibility in how video data is distributed. The 4:4:4 format carries separate component information at full resolution, while 4:2:2 support enables designs using fewer data paths when the source format permits it. The device is intended for complete video back-end conversion applications, including DVD players, personal video recorders, set-top boxes, and other systems that require digital component-video signals to become analog outputs. Its parallel operational architecture consolidates three conversion channels into one dedicated video-processing component rather than requiring three separate converter packages. Typical deployments include consumer video equipment, broadcast and monitoring systems, and legacy digital-video infrastructure transitioning to analog displays or processors. System designers should also account for synchronization, digital input timing, analog-output quality, reference-clock integrity, and correct handling of unsupported or unused channels when creating the board-level interface. Layout is especially important because an 80-pin HTQFP provides many digital and analog connections in a compact 12 x 12 mm footprint. Maintain short return paths for analog outputs, provide continuous supply planes where possible, decouple supply pins close to the device, and follow the manufacturer's pin-description and layout guidance when assigning traces. The exposed thermal pad and package outline must follow the land pattern specified for the PFP package. This product page combines the exact manufacturer identity, package and temperature information, sourcing structure, compatible family members, and application-specific design guidance. It also distinguishes documented functionality from electrical parameters that must be confirmed in the manufacturer datasheet before final schematic, signal-integrity, or thermal sign-off.

RFQ Contact
THVD1400DR - 3.3-5V RS-485 Transceiver, 500Kbps, 8-SOIC | Texas Instruments
THVD1400DR

THVD1400DR - 3.3-5V RS-485 Transceiver, 500Kbps, 8-SOIC | Texas Instruments

The Texas Instruments THVD1400DR is a 3.3-V to 5-V RS-485/RS-422 half-duplex transceiver in an 8-pin SOIC package, supporting data rates up to 500 kbps with integrated ±12-kV IEC ESD (HBM) protection on the bus pins. The part contains one driver and one receiver on a single die, operates from a 3.0 V to 5.5 V supply, and meets or exceeds the requirements of the TIA/EIA-485A standard for robust industrial communication. The wide common-mode voltage range and low input leakage on bus pins make the device suitable for multi-point applications over long cable runs. What is an RS-485 transceiver? An RS-485 transceiver is a type of differential line driver/receiver interface IC that converts a single-ended TTL/CMOS logic signal into a balanced differential signal on a twisted-pair bus, and vice versa. RS-485 belongs to the broader TIA/EIA-485 family of serial interface standards and is widely used in industrial automation, building control, and long-distance communication. The transceiver sits between a UART/MCU and the physical bus, providing the voltage translation, drive strength, and ESD protection required to survive harsh electrical environments. Key features include 1/8 unit load support (allowing up to 256 nodes on the bus), ±12-kV IEC 61000-4-2 contact discharge ESD protection on bus pins, hot-plug support with glitchless power-up, and an extended industrial operating temperature range of -40 °C to +125 °C. The THVD1400DR also integrates thermal shutdown, current limiting on driver outputs, and receiver fail-safe for open, shorted, or idle bus conditions, eliminating the need for external biasing resistors on many designs. The architecture combines a precision differential line driver with a high-CMRR receiver and on-chip charge-pump-generated drive rails. The wide bus common-mode range of -7 V to +12 V lets the device tolerate ground potential differences between nodes across long cable runs. The 8-pin SOIC footprint provides drop-in compatibility with industry-standard pinout, simplifying PCB reuse and second-sourcing. Typical applications include industrial fieldbus networks (Modbus, Profibus-compatible), HVAC building automation, solar inverter daisy-chains, motor drive control links, smart-grid metering, and any point-to-point or multi-drop RS-485 link requiring IEC-grade ESD robustness. The low quiescent current also makes it suitable for battery-backed or always-on telemetry nodes. When designing with this device, place 100 nF decoupling close to VCC and add a 1 µF bulk capacitor when long supply traces are present. For bus termination, use a 120 Ω resistor across the differential pair at the two end nodes only; intermediate nodes should not be terminated to preserve signal integrity on multi-drop buses.

RFQ Contact
THVD1450 - 50 Mbps RS-485 Transceiver, ±18 kV ESD | Texas Instruments
THVD1450

THVD1450 - 50 Mbps RS-485 Transceiver, ±18 kV ESD | Texas Instruments

The Texas Instruments THVD1450 is a 3.3-V to 5-V, half-duplex RS-485/RS-422 transceiver with ±18-kV IEC ESD protection, delivering data rates up to 50 Mbps in an 8-pin SOIC (D) package. It belongs to the THVD14xx family of noise-immune transceivers engineered for rugged industrial environments and supports a wide 3 V to 5.5 V supply range with a low-current standby mode for power-constrained designs. An RS-485 transceiver is a physical-layer device that converts a single-ended UART signal into a balanced differential signal for transmission over twisted-pair cabling, enabling robust communication across long distances and electrically noisy industrial settings. The RS-485 standard (TIA/EIA-485) defines a differential bus topology that allows up to 32 unit loads (256 with modern transceivers) on a single twisted pair, with common-mode voltage range of −7 V to +12 V and cable lengths beyond 1200 m at reduced speeds. Transceivers sit at the bottom of the OSI physical layer (PHY) and above the UART/SCI controller, framing all fieldbus, PROFIBUS, Modbus, BACnet, and DMX512 wiring as the dominant industrial multi-drop PHY in use today. Key features of the THVD1450 include ±18-kV IEC 61000-4-2 air-discharge ESD on bus pins (eliminating external TVS arrays), ±8-kV IEC contact discharge, integrated bus fail-safe biasing (open, short, idle), 1.5 V typical differential output swing into 54 Ω, hot-plug support with glitch-free power-up, and an operating junction temperature range of −40 °C to +125 °C. The 8-SOIC package provides a compact 3.9 mm × 4.9 mm footprint, suitable for point-to-point and multi-drop fieldbus links. Architecturally, the THVD1450 integrates a differential line driver, a wide-common-mode differential receiver, internal fail-safe bias resistors, and an IEC-ESD cell at the bus pins. The wide 3 V to 5.5 V supply range allows direct connection to either 3.3-V MCU rails or legacy 5-V logic, simplifying BOM in mixed-voltage industrial nodes. Typical applications include factory-automation fieldbus nodes, building-automation BACnet wiring, solar inverter daisy-chain comms, motor-drive encoder feedback, smart-meter data concentrators, and any noise-immune multi-drop RS-485 link where bus pins face direct human/operator contact and require maximum ESD survivability. The 50-Mbps speed grade also supports high-rate motion-control and vision-system links over short cable. When designing with this part, place 100 nF decoupling within 2 mm of VCC and add a 120 Ω termination resistor at each cable end only. Avoid stubs longer than one-tenth of the driver rise time to prevent reflections at 50 Mbps, and never tie the bus pins to a stub that exceeds the unit-load budget of 32 (or 256 with low-IU parts). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including same-family THVD14xx options, cross-brand pin-compatible RS-485 transceivers, and IEC-ESD design-in guidance for rugged industrial nodes.

RFQ Contact
THVD1450D - 3.3-5V RS-485 Transceiver ±18kV ESD | TI
THVD1450D

THVD1450D - 3.3-5V RS-485 Transceiver ±18kV ESD | TI

The Texas Instruments THVD1450D is a 3.3-V to 5-V RS-485/RS-422 transceiver housed in an 8-pin SOIC package, featuring integrated IEC 61000-4-2 ±18-kV ESD protection on the bus pins. The device integrates one driver and one receiver (1/1 configuration) in half-duplex mode and supports data rates up to 50 Mbps over a wide 3.0V-5.5V supply range. An RS-485/RS-422 transceiver is a physical-layer interface IC that translates logic-level UART or SPI signals from a microcontroller into the differential voltage signaling required by the RS-485 and RS-422 standards. Differential signaling allows data transmission over long cable runs (up to 1200 m per the RS-485 standard) in electrically noisy industrial environments, because common-mode noise is rejected by the receiver's differential comparator. Within the broader system hierarchy, the transceiver sits between the controller's UART/SPI logic and the physical twisted-pair bus, sitting alongside other power-management and interface ICs on the bus node's BOM. Key features include ±18-kV HBM-equivalent IEC 61000-4-2 ESD protection on the A and B bus pins, ±4-kV IEC 61000-4-4 EFT immunity, a 30-mV receiver hysteresis for noise rejection, and a wide -40°C to +125°C operating temperature range. The wide 3.0V-5.5V supply range makes the part compatible with both 3.3V and 5V MCU rails without level shifters, while the 1/1 half-duplex configuration is the most common building block for daisy-chained or point-to-point RS-485 nodes. The device architecture uses a differential line driver with controlled slew rate to limit EMI, and a differential comparator receiver with 30-mV hysteresis to reject bus noise and reflection-induced ringing. The integrated IEC 61000-4-2 ESD cells on the bus pins (tolerant to ±18 kV contact/air discharge) eliminate the need for external TVS protection in most industrial installations, reducing BOM cost and PCB area. The part is part of TI's THVD14xx family, which shares pinout and feature set across data-rate grades. Typical applications include industrial factory automation, HVAC networks, building-automation RS-485 trunks, motor-control encoder feedback, smart-grid metering, and any embedded system that needs a rugged 3.3V/5V RS-485 node with strong system-level ESD/EFT immunity. When designing with this device, place 100-nF decoupling capacitors as close as possible to the VCC pin and follow RS-485 cable-stub length recommendations. Note that the wide-supply 3.0V-5.5V range allows direct connection to both 3.3V and 5V MCUs, but the bus common-mode voltage must remain within the -7V to +12V range defined by the standard. This page synthesizes distributor stock, drop-in alternatives, and practical design notes that complement the manufacturer datasheet with real BOM-level guidance.

RFQ Contact
THVD1450DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD, 50Mbps | TI
THVD1450DRBR

THVD1450DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD, 50Mbps | TI

The Texas Instruments THVD1450DRBR is a 3.3-V to 5-V RS-485/RS-422 half-duplex transceiver housed in an 8-pin VSON EP (DRB) package measuring 3x3 mm, supporting data rates up to 50 Mbps with integrated ±18-kV IEC 61000-4-2 ESD protection on the bus pins. It operates from a single 3-V to 5.5-V supply and provides one driver and one receiver (1/1) on a shared differential bus pair for two-wire multi-drop topologies. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts between a single-ended UART/logic signal on the controller side and a differential voltage on a twisted-pair cable. Half-duplex operation means the same differential pair is shared between transmit and receive paths, reducing wire count for multi-drop industrial networks such as Modbus RTU, Profibus, and DMX512. Within the broader signal-chain taxonomy, the THVD1450 belongs to the transceiver -> line driver/receiver -> interface IC -> power-tree signal-chain hierarchy used in industrial automation, building automation, and point-of-sale equipment. Key differentiating features include ±18-kV IEC 61000-4-2 contact/air ESD immunity on the bus pins, ±4-kV IEC 61000-4-4 EFT immunity, and a wide 3-V to 5.5-V supply range that allows direct connection to 3.3-V MCUs or 5-V legacy controllers without external level shifters. The integrated fail-safe biasing on the receiver guarantees a known logic-high output when the bus is idle, shorted, or open. The 8-pin VSON EP package with exposed thermal pad occupies only 3x3 mm, suitable for dense fieldbus nodes and compact sensor modules. The architecture uses a differential line driver with controlled slew rate and a differential comparator receiver with 30 mV of hysteresis for noise rejection. The wide common-mode range (typically -7 V to +12 V) tolerates ground-potential differences between nodes on long cable runs, while the 1-unit-load receiver (32 nodes) supports large multi-drop networks within Modbus-style installations. Typical applications include industrial fieldbus networks, motor-drive feedback links, building-automation gateways, solar inverter monitoring, and any cable link requiring IEC-rated ESD/EFT robustness. The bus pins survive ±18-kV contact discharge per IEC 61000-4-2, eliminating external TVS diode arrays in many designs. When designing with this part, place a 100 nF decoupling capacitor close to VCC, respect the DRB exposed-pad layout for thermal spreading, and rely on the internal fail-safe biasing rather than an external resistor network. The wide common-mode range means most cable installations work without additional protection circuitry. This page consolidates distributor pricing, drop-in alternatives in the same 8-VSON footprint, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
THVD1451DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD | TI
THVD1451DRBR

THVD1451DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD | TI

The Texas Instruments THVD1451DRBR is a 3.3-V to 5-V RS-485 transceiver housed in an 8-pin VSON (DRB) package with 3x3 mm footprint, featuring ±18-kV IEC 61000-4-2 ESD protection on the bus pins. The device integrates one driver and one receiver (1/1 transceiver), supports half-duplex communication, and operates across a wide 3.0 V to 5.5 V supply range compatible with both 3.3 V and 5 V system rails. An RS-485 transceiver is a physical-layer interface IC that converts differential bus signals to single-ended logic levels, enabling robust half-duplex or full-duplex serial communication over twisted-pair cabling in electrically noisy industrial environments. RS-485 belongs to the broader TIA/EIA-485 standard family of differential transceivers, used as the physical layer for protocols such as Modbus RTU, PROFIBUS, DMX512, and BACnet. The THVD1451 sits within TI's THVD family, which adds integrated IEC ESD protection that eliminates external TVS diodes in many designs. Key features include ±18-kV IEC 61000-4-2 contact discharge ESD protection on the bus pins, ±8-kV IEC 61000-4-2 air-gap discharge, ±4-kV EFT, and ±1.5-kV surge (2 Ω source). The device supports up to 50 Mbps signaling rate, features a low standby current of < 5 µA, and offers 1/8 unit-load fanout supporting up to 256 nodes on a single bus. Thermal and fault protection includes thermal shutdown, current limiting on driver outputs, and bus pin fail-safe biasing that keeps the receiver output in a defined state when the bus is floating. The THVD1451 uses a 3.3 V/5 V CMOS process with precision differential line drivers, achieving low driver skew and rail-to-rail common-mode range from -7 V to +12 V on the bus. The wide common-mode tolerance makes the device tolerant of ground potential differences between nodes in long-cable runs, a defining requirement of the RS-485 standard. The integrated IEC 61000-4-2 ESD protection reduces board area and BOM cost by replacing discrete TVS arrays. Typical applications include factory automation PLCs, building automation HVAC controllers, solar inverter communication gateways, smart-grid metering, and motor drive encoder feedback links. The wide supply and common-mode ranges also support battery management system (BMS) daisy-chained monitoring where nodes see different ground references. Design tip: place the THVD1451 as close as possible to the bus connector with a solid ground pour beneath the exposed pad to maximize ESD dissipation. For full ±18-kV IEC contact discharge protection the PCB ground must be low-impedance; a stitching capacitance of 1 nF Y1-rated between bus ground and chassis is recommended. This page synthesizes distributor pricing, drop-in alternatives and design notes not found in the manufacturer datasheet alone, helping engineers select pin-compatible RS-485 ICs with comparable ESD ratings for industrial and factory-automation designs.

RFQ Contact
THVD1452D - 3.3-5V RS-485 Transceiver, ±18kV IEC ESD | TI
THVD1452D

THVD1452D - 3.3-5V RS-485 Transceiver, ±18kV IEC ESD | TI

The Texas Instruments THVD1452D is a 3.3-V to 5-V RS-485 transceiver with ±18-kV IEC ESD protection, housed in a 14-pin SOIC (D) package. The device integrates one driver and one receiver (1/1) in a full-duplex configuration, supporting data rates suitable for factory automation, motor drive, and industrial process control networks. The wide 3.0-V to 5.5-V supply range allows direct interfacing to 3.3-V MCUs as well as legacy 5-V UARTs without level shifters. An RS-485 transceiver is a differential line driver/receiver IC designed for robust, long-distance, half- or full-duplex serial communication over twisted-pair cabling. RS-485 transceivers belong to the interface IC family within the broader semiconductor hierarchy (interface IC -> communication transceiver -> differential bus transceiver -> semiconductor). They convert single-ended TTL/CMOS logic levels into differential signals compliant with the TIA/EIA-485 standard, enabling multi-drop networks of up to 32 unit loads on a single bus segment with excellent immunity to common-mode noise. Key features of the THVD1452D include ±18-kV IEC 61000-4-2 ESD protection on the bus pins (HBM ±16 kV, contact discharge ±6 kV), a 1/8 unit-load receiver input impedance allowing up to 256 nodes on the bus, true fail-safe biasing on the receiver outputs, and integrated IEC 61000-4-4 EFT protection. The device operates across the industrial -40 °C to +125 °C temperature range and provides thermal shutdown with automatic recovery. The architecture combines a precision differential line driver with a wide-common-mode receiver that detects signals as low as ±200 mV in the presence of ±25 V common-mode voltage. This robust receiver design eliminates the need for external fail-safe resistors and supports reliable operation in electrically noisy industrial environments such as motor inverters and HVAC equipment. Typical applications include factory automation networks, motor drive position feedback, building automation (HVAC, lighting, access control), solar inverter communications, and any point-to-point or multi-drop RS-485 link requiring strong system-level ESD/EFT robustness without external protection components. When designing with the THVD1452D, place the bus pins' decoupling capacitor as close as possible to VCC (pin 13) and route the differential A/B traces as a 100-Ω differential pair with ground reference. Use a 120 Ω resistor across A and B at the cable ends for termination. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact