Products (44,000+)

LIFCL-40-8MG289C - 39K LUT CrossLink-NX FPGA, 289-BGA | Lattice
LIFCL-40-8MG289C

LIFCL-40-8MG289C - 39K LUT CrossLink-NX FPGA, 289-BGA | Lattice

The Lattice LIFCL-40-8MG289C is a 39K logic element CrossLink-NX FPGA from Lattice Semiconductor, packaged in a 289-ball caBGA (9.5 mm x 9.5 mm) and targeted at low-power embedded vision bridging and processing. It provides 180 high-performance user I/O, 1,548,288 bits of embedded block RAM, and integrated 2.5G MIPI D-PHY hard IP for direct camera/sensor interfacing. What is a CrossLink-NX FPGA? The CrossLink-NX family is Lattice's low-power, small-form-factor FPGA line built on the 28 nm FD-SOI Nexus platform. As an FPGA (Field-Programmable Gate Array), it belongs to the programmable logic hierarchy: PLD -> CPLD -> FPGA -> embedded FPGA -> CrossLink-NX. FPGAs differ from CPLDs in that they integrate configurable logic blocks, dedicated block RAM, DSP blocks, and high-speed transceivers, all interconnected through a programmable fabric. CrossLink-NX specializes in bridging heterogeneous video and sensor interfaces with best-in-class power efficiency. Key features of the LIFCL-40-8MG289C include 39,000 LUTs (logic elements), 1.548 Mbit embedded SRAM, dedicated MIPI D-PHY at up to 2.5 Gbps per lane, integrated DDR3/LPDDR3 memory controller with PHY, and 7 x 2.5G hard PCIe lanes (Gen2). The device is built on a 28 nm FD-SOI low-power process, supports 0.95 V to 1.05 V core Vcc, and offers programmable I/O supporting LVCMOS 1.2/1.5/1.8/2.5/3.3 V, LVDS, SLVS, and sub-LVDS. The architecture combines hardened MIPI D-PHY and PCIe Gen2 controllers with the programmable Nexus fabric to deliver deterministic latency at low mW power levels. Transceivers support 2.5 Gbps MIPI, and the device targets edge AI pre-processing, sensor aggregation, and video bridging where traditional FPGAs would be too power-hungry. Typical applications include multi-camera sensor aggregation in robotics and ADAS, machine vision frame grabbers, MIPI-to-MIPI/CSI-to-LVDS bridging, embedded display controllers, and edge AI pre-processing pipelines. Its low power envelope also suits battery-powered wearables and AR/VR glasses. When designing with this device, use Lattice Radiant or Propel SDK and the CrossLink-NX evaluation board for bring-up. Provide adequate decoupling per the reference design, and follow Lattice PCB layout guidelines for 289-BGA breakout routing.

RFQ Contact
LIFCL-40-9MG289C - CrossLink-NX 39K LUT FPGA, 289-TFBGA | Lattice
LIFCL-40-9MG289C

LIFCL-40-9MG289C - CrossLink-NX 39K LUT FPGA, 289-TFBGA | Lattice

The Lattice LIFCL-40-9MG289C is a CrossLink-NX family field-programmable gate array (FPGA) built on the Lattice Nexus platform, delivering 39000 logic elements, 1548288 bits of embedded memory, and 180 user I/O in a 289-ball TFBGA (CSBGA) package. The part integrates 2.5 Gbps MIPI D-PHY hard IP cores targeting embedded vision bridging and processing applications, while a commercial temperature grade (-9) supports 0C to +85C operation. What is a CrossLink-NX FPGA? An FPGA (Field Programmable Gate Array) is a semiconductor device whose logic fabric, interconnect, and I/O can be reconfigured after manufacturing by the customer. The CrossLink-NX family belongs to the broader category of programmable logic devices (PLDs), which also includes CPLDs. FPGAs sit within the integrated circuit taxonomy as follows: FPGA -> programmable logic -> logic IC -> integrated circuit. CrossLink-NX specifically targets low-power embedded vision bridging, providing hard MIPI D-PHY/CSI-2 cores, hardened memory controllers, and a high-performance fabric for sensor aggregation. Key features include up to 75% lower power compared to similar FPGAs in its class, 2.5G MIPI D-PHY/CSI-2 hard cores enabling direct connection to image sensors and displays, embedded block RAM, distributed SRAM, and on-chip DSP slices. The Nexus platform also provides high reliability for mission-critical applications including automotive and industrial segments. The architecture combines a small-form-factor 289-ball TFBGA package with hardened I/O, allowing PCB designs to keep sensor and display trace lengths short. Designers benefit from Lattice Radiant software support and pre-built IP libraries for MIPI bridging, display controllers, and image signal processing pipelines. Typical applications include embedded vision bridging for camera sensors, AI inference at the edge, machine vision in industrial automation, AR/VR head-mounted displays, and video aggregation/duplication for surveillance and automotive infotainment. When designing with this part, ensure PCB layout follows the BGA escape pattern documented in the Lattice hardware manual and that decoupling capacitors are placed directly under the package balls for clean power delivery to the fabric. This page synthesizes distributor stock, drop-in same-family alternatives, and design notes not found in the manufacturer datasheet. All information reflects availability as of 2026-10-10.

RFQ Contact
LM-555N - Single 555 Timer, 8-PDIP | Texas Instruments
LM-555N

LM-555N - Single 555 Timer, 8-PDIP | Texas Instruments

The Texas Instruments LM-555N is a single 555-type timer and oscillator integrated circuit packaged in an 8-pin PDIP. The verified distributor result identifies it as an 8-PDIP device from Harris Corporation, while the official TI family page identifies the LM555 as a highly stable 555 timer. The target MPN is therefore associated with the classic timer functionality, but the supplied data does not provide verified electrical ratings, timing limits, temperature range, or lifecycle details for the exact LM-555N ordering code. What is a 555 timer? A 555 timer is a programmable timer and oscillator integrated circuit used to generate delayed pulses, produce periodic waveforms, debounce inputs, or control relays and indicators. Its internal blocks typically include a voltage reference, comparators, a flip-flop, and a high-current output stage. In astable operation, external resistors and a capacitor set the oscillation period; in monostable operation, an external timing capacitor sets the output pulse width. The verified Harris product description identifies the LM555N for timing-delay and oscillator applications in commercial, industrial, and military equipment. The verified product listing calls it a “555 Type, Timer/Oscillator (Single) IC” and specifies an 8-PDIP package. The official TI product page describes the LM555 family as a highly stable 555 timer and provides family-level documentation, but the supplied material does not expose the exact LM-555N datasheet values. Because the target MPN includes a hyphen while the verified distributor listing uses LM555N, engineers should confirm the exact package, suffix, manufacturer, and electrical limits against the applicable manufacturer documentation before substituting or releasing a production design. The verified result also shows a distributor listing from Rochester Electronics under the Harris Corporation name; Harris Corporation is not in the supplied Manufacturer Reference, so the brand field follows the target context and the official TI source uses Texas Instruments. Typical uses include pulse generation, delay circuits, oscillators, indicator flashing, switch debouncing, and simple industrial control logic. Because the exact pinout, package details, and ratings were not included in the verified data, this page does not infer those values. Check the original LM-555N datasheet and the manufacturer’s current documentation before layout or purchase.

RFQ Contact
LM111 - High-Speed Differential Comparator | Texas Instruments
LM111

LM111 - High-Speed Differential Comparator | Texas Instruments

The Texas Instruments LM111 is a single high-speed differential voltage comparator with open-collector and open-emitter outputs, designed for operation from a single 5 V supply through dual ±15 V supplies. Its stated maximum input bias current is 300 nA, maximum input offset current is 70 nA, and the device includes strobe capability for controlled comparator operation. The LM111 is packaged in an 8-pin TO-99 style metal can package. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The LM111 belongs to the comparator category within analog and interface ICs, and its differential inputs make it useful for threshold detection, signal conditioning, timing, and control systems. Unlike an operational amplifier intended primarily for linear amplification, the comparator is optimized for rapid state changes and logic-level output compatibility. The LM111, LM211, and LM311 family is designed around a wide supply-voltage range, including ±15 V operational-amplifier supplies and 5 V logic systems. The output levels are compatible with many TTL and MOS circuits, allowing the LM111 to bridge analog sensing and digital control. Its differential input arrangement supports sensing a small difference between two voltages while presenting a logic result to downstream circuitry. The LM111 family also includes related temperature grades and device variants. Texas Instruments states that the LM111-N has the same pin configuration as the LM106 and LM710, while the LM211-N and LM311-N provide different specified temperature ranges. The exact LM111 pin configuration and electrical limits must be confirmed against the applicable manufacturer datasheet and package variant before production release. Typical applications include line and threshold comparators, pulse and window detection, level translation into TTL or MOS logic, industrial control interfaces, analog signal conditioning, and legacy instrumentation. Because the output is open collector or open emitter, a pull-up or pull-down load resistor is generally required at the output. This architecture can provide wired logic behavior and flexible output interfacing, but it also makes pull-device selection and output speed part of the system design. When selecting a replacement, verify the package, pinout, supply limits, input offset and bias behavior, response time, output topology, and temperature grade. The verified material supports the LM111 identity and family-level characteristics, but it does not provide enough verified information here to reproduce every electrical limit or package drawing. This page therefore distinguishes documented values from parameters requiring confirmation rather than guessing them.

RFQ Contact
LM111-LM211 - High-Speed Differential Comparator | Texas Instruments
LM111-LM211

LM111-LM211 - High-Speed Differential Comparator | Texas Instruments

The Texas Instruments LM111-LM211 is a family designation for single, high-speed differential voltage comparators designed to operate from wide power-supply ranges, including ±15 V operational-amplifier supplies and single +5 V logic supplies. The comparator combines low input current with an open-collector output whose logic levels are compatible with many TTL and MOS circuits. The available ordering variants include LM111, LM211, and LM311 devices documented by the manufacturer under the LM111, LM211, and LM311 differential comparator datasheet. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. In the broader electronics hierarchy, a differential comparator belongs to comparator ICs, analog-to-digital decision interfaces, and signal-conditioning semiconductors. It is commonly used where a sensor, reference voltage, timing ramp, or control signal must be translated into a logic-level event. The LM111, LM211, and LM311 devices are described by Texas Instruments as single high-speed voltage comparators. Their low input currents are useful when the driving source has high impedance or when input bias current could otherwise create measurement errors. The family supports conventional ±15 V supplies and +5 V logic-system operation, making it suitable for legacy analog, control, timing, and industrial interface circuits. Output levels are compatible with most TTL and MOS circuits, although the open-collector output requires an appropriate pull-up arrangement. The LM111, LM211, and LM311 differ primarily in their specified operating-temperature families: TI identifies the LM111-N as specified from −55°C to +125°C, the LM211-N from −25°C to +85°C, and the LM311-N from 0°C to +70°C. The target string LM111-LM211 is therefore a family or ordering designation rather than one uniquely specified package-and-temperature variant. The exact commercial suffix, package, pin configuration, and current availability must be confirmed against the selected manufacturer orderable part. Typical uses include precision voltage thresholding, zero-crossing detection, peak detection, window comparison, pulse timing, sensor interface conditioning, and control logic interfacing. The comparator is placed between a signal source and a downstream TTL or MOS input, with its output configured to drive the receiving device through a suitable pull-up or interface network. Engineers should verify supply polarity, input common-mode limits, output pull-up voltage, switching behavior, and input offset requirements in the manufacturer datasheet before layout release. The key design consideration is that an open-collector comparator is not a push-pull logic driver. The output node floats when the device is off, so the external pull-up resistor, pull-up voltage, load capacitance, and required logic rise time must be selected together. Input filtering and grounding are also important when the comparator is used near precision thresholds or noisy switching nodes. This page distinguishes verified family-level facts from parameters that require a specific package and orderable suffix. This page synthesizes the verified manufacturer and distributor references for the LM111-LM211 family, separates documented family-level capabilities from orderable-device requirements, and highlights the design decisions that determine whether an open-collector comparator is suitable in a given circuit. The alternatives listed here are limited to parts explicitly supported as same-family or comparator cross-reference candidates; exact replacement must be checked against the selected package and suffix.

RFQ Contact
LM111-MDE - High-Speed Voltage Comparator Die | Texas Instruments
LM111-MDE

LM111-MDE - High-Speed Voltage Comparator Die | Texas Instruments

Texas Instruments LM111-MDE is a single, high-speed voltage comparator die designed for operation from wide-range power supplies, including ±15 V operational-amplifier rails and 5 V logic systems. The verified source identifies a single-channel general-purpose comparator with a maximum input offset voltage of 3 mV at ±15 V, maximum quiescent current of 6 mA, and an operating temperature range of -55°C to 125°C. Because the -MDE ordering code denotes a die sale, the component is supplied as an unpackaged semiconductor die rather than a leaded or surface-mount package. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. Within the semiconductor hierarchy, the LM111 belongs to the comparator family, a functional class of analog and mixed-signal ICs used between sensors, transducers, amplifiers, and digital logic. The LM111 family is associated with high-speed decision-making and compatibility with common TTL and MOS output systems, while its open-collector-style output requires an appropriate pull-up arrangement for reliable digital interfacing. The LM111 family provides a single comparator channel and supports a broad supply-voltage range. The verified manufacturer description states that the LM111, LM211, and LM311 are single high-speed voltage comparators. Its output levels are compatible with most TTL and MOS circuits, making the device useful for threshold detection, pulse-width or timing decisions, signal conditioning, and control systems. The maximum input offset voltage of 3 mV at ±15 V defines the comparison accuracy limit, while the 6 mA maximum quiescent current provides a basis for power-supply budgeting. The die-sale format requires special assembly consideration. No package pinout, package dimensions, or exposed thermal pad can be inferred from the verified data because LM111-MDE is sold as a die. A designer must obtain the manufacturer die documentation and assembly requirements before bonding or packaging the device. In particular, do not assume that the die's bond-pad arrangement matches the LM111 leaded-package pinout. The verified source also identifies -55°C to 125°C as the operating temperature range for LM111-MDE, but no die-specific thermal resistance or power rating is provided. Typical uses include high-speed threshold detection, pulse and window comparisons, industrial control interfaces, analog signal conditioning, and logic-level decision circuits. Because the output is intended to interoperate with TTL and MOS systems, the external pull-up network, supply bypassing, input grounding, and output loading are critical. Compared with a finished package, the die-sale device offers sourcing and customization flexibility but requires wafer handling, die attach, wire bonding or other packaging, and application-specific qualification. This product page combines the verified manufacturer and distributor data with practical die-level design guidance, sourcing context, and strict handling of unavailable package information. It is intended to help engineers distinguish the LM111-MDE die sale from packaged LM111 variants and to plan assembly, testing, and supply-chain risk before committing the device to a production design.

RFQ Contact
LM111-MW8 - High-Speed Voltage Comparator | Texas Instruments
LM111-MW8

LM111-MW8 - High-Speed Voltage Comparator | Texas Instruments

The Texas Instruments LM111-MW8 is a single high-speed voltage comparator designed for operation from wide-range power supplies, including ±15 V operational-amplifier supplies and 5 V logic systems. The verified product material identifies the LM111 family as a comparator with low input bias current and fast response, while the exact LM111-MW8 package, pinout details, electrical limits, operating temperature range, and orderable package variant are not supplied in the provided data. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the differential input crosses a defined threshold. The LM111 belongs to the comparator, analog IC, and signal-conditioning hierarchy rather than the operational-amplifier category, although it can be used in threshold detection, sensing, pulse-width, and control circuits. Its wide supply compatibility allows the same device family to interface with traditional analog rails and lower-voltage logic systems. The LM111 family is specified as a single high-speed voltage comparator. The verified material specifically cites maximum input bias current of 300 nA and maximum input offset current of 70 nA, along with operation from a single 5 V supply. These characteristics are relevant where low input loading and precise threshold behavior are important. The output levels are stated to be compatible with most TTL and MOS circuits, which supports use as a decision element between analog signals and digital control logic. Typical comparator applications include level crossing, overvoltage and undervoltage indication, signal translation, pulse generation, window detection, and interface conditioning. The fast-response description is useful when the comparator must resolve changing waveforms rather than merely provide static threshold monitoring. The published family material also mentions strobe capability, but the exact LM111-MW8 operating conditions and timing values require confirmation in the manufacturer datasheet before design release. Because the provided data does not specify the LM111-MW8 package dimensions, pin names, temperature grade, or exact electrical maximums, those values must be verified against the official Texas Instruments documentation. Do not assume that a similarly named LM111, LM211, or LM311 orderable part is mechanically interchangeable. In particular, LM211 and LM311 are distinct family variants and may have different supply, temperature, or output requirements. This page consolidates the verified Texas Instruments family description, distributor discovery information, and official datasheet references. It also separates confirmed facts from missing LM111-MW8-specific data so engineers can plan sourcing and schematic review without treating unverified package or performance details as specifications.

RFQ Contact
LM201AD - 1 MHz Single Op Amp, 8-SOIC | STMicroelectronics
LM201AD

LM201AD - 1 MHz Single Op Amp, 8-SOIC | STMicroelectronics

The STMicroelectronics LM201AD is a single general-purpose operational amplifier supplied in an 8-pin SOIC package. The device is listed as a non-compensated, single operational amplifier with a nominal gain-bandwidth product of 1 MHz, a slew rate of 0.5 V/us, and a dissipation rating of 300 mW. Its stated supply range is plus or minus 5 V to plus or minus 22 V, allowing operation from a 10 V minimum total supply to a 44 V maximum total supply. The LM201AD also provides push-pull output capability according to distributor listings. An operational amplifier is an analog signal-conditioning integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM201 family is positioned as a general-purpose amplifier rather than a precision micropower device or a high-speed rail-to-rail amplifier. Its non-compensated architecture requires the user to add external compensation when closed-loop stability is needed, making it most suitable for designs in which the engineer selects a specific gain, bandwidth, and phase-margin target. Verified distributor information identifies the LM201AD as a one-amplifier, 8-SOIC device. One distributor listing reports a 1 MHz gain-bandwidth product, while a separate Mouser listing identifies a 3.5 MHz gain-bandwidth figure. These values may reflect different source pages or gain and condition definitions, so the two figures should be confirmed against the exact STMicroelectronics datasheet revision before setting compensation networks or estimating closed-loop bandwidth. Typical uses include general analog signal conditioning, instrumentation interfaces, active filtering, and feedback control in industrial or test equipment where higher supply voltages are acceptable. Because this is a non-compensated amplifier, external compensation components and stability analysis are normally required. The wide plus or minus 22 V capability also makes rail-to-rail input and output operation unlikely, so input and output common-mode and swing limits must be respected. For PCB design, place the amplifier close to feedback and compensation components, keep input nodes away from switching nodes and high-current paths, and provide adequate ground return connectivity for the single-supply return terminal. Decoupling requirements should be confirmed from the manufacturer datasheet rather than inferred from the distributor listings. This page combines verified distributor specifications, package information, cross-reference results, and engineering guidance that are not consolidated in a single manufacturer product listing. Pricing, pin-level data, lifecycle details, and compensation requirements should be verified against the current STMicroelectronics datasheet before production release.

RFQ Contact
LM201ADG - Single 10 V/us Op Amp in 8-SOIC | onsemi
LM201ADG

LM201ADG - Single 10 V/us Op Amp in 8-SOIC | onsemi

onsemi LM201ADG is a single, non-compensated operational amplifier with a 10 V/us slew rate, 5 V to 20 V supply range, and 8-SOIC package. The LM201 family is designed for general-purpose analog signal conditioning and lets the user select an external compensation capacitor suited to the required stability, gain, and bandwidth. Its single-amplifier configuration supports space-efficient analog designs requiring one high-speed amplifier per package. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM201 belongs to the broader operational-amplifier, linear-amplifier, analog-IC, and semiconductor hierarchies. Unlike a unity-gain-stable op amp, the LM201 is non-compensated, so its closed-loop behavior depends on the external compensation network, feedback topology, load, and desired gain. Principal features include a 10 V/us slew rate, a Class AB output stage, external frequency compensation, and low input bias and offset current. These characteristics make the device useful when conventional internally compensated amplifiers do not provide enough speed or flexibility. Users can tailor the compensation capacitor to optimize stability and bandwidth for a particular amplifier gain. The LM201ADG operates from 5 V to 20 V, allowing use with conventional single supplies or dual supplies derived from split rails. Its non-inverting and inverting inputs support standard feedback arrangements, while the output stage drives external compensation networks and downstream analog stages. Because stability is intentionally user-configured, the selected compensation value and closed-loop gain must be evaluated together rather than treated as an independent component choice. Typical applications include instrumentation signal conditioning, active filtering, summing and difference amplifiers, analog control loops, sensor interfaces, and general-purpose laboratory electronics. The device is especially suitable for designs where adjustable compensation provides a better bandwidth-versus-stability balance than a fixed-compensation amplifier. The primary design consideration is stability. Check the required gain, load capacitance, output current, supply voltage, and recommended compensation value before finalizing the feedback network. Keep the compensation and feedback components close to the amplifier pins, provide adequate supply bypassing, and avoid long PCB traces that can add parasitic capacitance and alter closed-loop response. This product page combines the LM201ADG electrical identity with practical compensation guidance, pin information, verified source links, and a selection-focused comparison against documented substitute parts. It is intended to help engineers identify the correct package, confirm replacement compatibility, and plan a stable implementation before placing the component into production.

RFQ Contact
LM201ADT - 22V Precision Op Amp, 3.5MHz | STMicroelectronics
LM201ADT

LM201ADT - 22V Precision Op Amp, 3.5MHz | STMicroelectronics

STMicroelectronics LM201ADT is a general-purpose precision operational amplifier in an 8-pin SOIC package. It operates from ±5V to ±22V, supports single or dual supplies, provides a 3.5 MHz gain-bandwidth product, and has a 0.5 V/µs slew rate. The LM201A series also includes input and output overload protection, low input offset current, and stable operation without oscillation when the common-mode input range is exceeded. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier whose closed-loop behavior is determined primarily by external feedback components. The op amp category belongs to the broader amplifier-IC and signal-conditioning hierarchy, where precision amplifiers are used for current sensing, analog measurement, filtering, buffering, instrumentation, and closed-loop control. A precision operational amplifier is selected when low offset, controlled gain, and predictable operation are more important than very high bandwidth. The LM201ADT combines a 22V maximum supply rating with moderate speed and precision-oriented behavior. Its 3.5 MHz gain-bandwidth product supports useful closed-loop bandwidth in amplifier networks of moderate gain, while its 0.5 V/µs slew rate limits large-signal response. Input and output overload protection improves robustness in applications where transient signals or output drive conditions may exceed normal operating limits. The amplifier is not internally compensated, allowing engineers to select stability by adding an external compensation capacitor. The LM201A documentation describes compensation with a 30 pF capacitor. This flexibility supports unity-gain stability and higher closed-loop gains, but it also requires careful selection of compensation and feedback values to avoid ringing or oscillation. Typical uses include instrumentation-amplifier front ends, precision current sensing, buffered sensor interfaces, active filters, analog measurement chains, and low-frequency control loops. The wide supply-voltage range is useful in industrial systems that use ±15V or ±22V rails, while its low-offset characteristics help preserve accuracy when the op amp operates near its input range. Design with the LM201ADT by checking common-mode and output swing against the actual supply voltage. Keep feedback-loop routing short, place compensation and decoupling capacitors close to the device, and verify stability at the intended closed-loop gain. The STMicroelectronics LM201A datasheet is the controlling reference for pin functions, compensation, electrical limits, and test conditions. This page combines the LM201ADT operating limits, package information, direct replacement considerations, comparison parameters, and practical design guidance to support faster component selection and PCB implementation.

RFQ Contact
LM201AH - 1 MHz General-Purpose Op Amp | Texas Instruments
LM201AH

LM201AH - 1 MHz General-Purpose Op Amp | Texas Instruments

Texas Instruments LM201AH is a single-channel, general-purpose operational amplifier with 1 MHz gain-bandwidth product, 80 dB common-mode rejection ratio, 2 mV input offset voltage, and approximately 1.8 mA supply current, housed in an 8-pin TO-99 hermetic metal-can package. It is intended for instrumentation, analog measurement, filtering, buffering, current sensing, and precision-control circuits operating from -40 °C to +85 °C. An operational amplifier, or op amp, is a high-gain differential-input amplifier whose feedback network determines its closed-loop behavior. The LM201AH belongs to the general-purpose operational-amplifier class within the broader amplifier IC and signal-conditioning hierarchy. Its TO-99-8 construction provides a through-hole package option for laboratory, industrial, and legacy instrumentation designs where surface-mount compatibility is not required. The principal performance features include a 1 MHz gain-bandwidth product, 80 dB CMRR, 2 mV input offset voltage, and approximately 1.8 mA operating current. The wide common-mode rejection specification helps reduce unwanted behavior when the amplifier handles small signals superimposed on larger voltage references or sensor outputs. The hermetic TO-99-8 package supports applications requiring a conventional metal-can outline and eight through-hole connections. The LM201A family uses advanced processing to reduce input bias current and temperature drift while retaining the general-purpose characteristics of the earlier LM101A architecture. The device can operate with conventional dual power supplies, making it suitable for signal paths centered around ground. Engineers should nevertheless verify supply-voltage limits, input common-mode range, output swing, compensation requirements, and electrical limits against the manufacturer datasheet before finalizing a design. Typical uses include laboratory instrumentation, analog measurement front ends, active filters, transducers, current-sensing amplifiers, and precision feedback loops. In a filter or amplifier, its 1 MHz gain-bandwidth product limits usable closed-loop bandwidth according to the selected noise-gain configuration. For sensor interfaces, the 80 dB CMRR can help reject common-mode interference, while the 2 mV offset remains an important error term in precision measurements. When designing around the LM201AH, begin by checking the required output swing and input common-mode range at the actual supply voltage. Decoupling should be placed close to the power pins, and the circuit should avoid driving capacitive loads unless stability behavior has been evaluated. Because the exact pin names and electrical limits are not included in the supplied search excerpts, those details should be confirmed in the Texas Instruments LM201A-N documentation before PCB release. This page consolidates the supplied distributor and manufacturer listings with practical selection guidance, package-aware alternatives, comparison parameters, and design cautions. It distinguishes confirmed data from unavailable fields so engineers can verify critical specifications without relying on assumptions.

RFQ Contact
LM201AN - Single Non-Compensated Op Amp | STMicroelectronics
LM201AN

LM201AN - Single Non-Compensated Op Amp | STMicroelectronics

The STMicroelectronics LM201AN is a single, general-purpose, non-compensated bipolar operational amplifier supplied in an 8-pin PDIP package. The confirmed headline characteristics are one amplifier circuit per package, a maximum input offset current of 20 nA over the operating temperature range, and the ability to obtain a slew rate of 10 V/µs when compensated appropriately for the intended circuit. An operational amplifier is a high-gain, differential-input analog building block used to amplify voltage differences, buffer signals, and perform linear operations such as summation, integration, and filtering. The LM201 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog IC, and semiconductor. Unlike a unity-gain-stable amplifier with internal compensation, the LM201AN is externally compensatable, allowing the circuit designer to select a compensation capacitor suited to the gain, bandwidth, and stability requirements of a particular application. Key features include a low input offset current, a maximum of 20 nA over temperature, and user-selectable compensation. These characteristics are especially relevant to precision analog circuits in which bias-current loading, input balance, and closed-loop stability can materially affect signal integrity. The device is offered as a single amplifier rather than a multi-amplifier package, simplifying board partitioning when separate analog channels require independent compensation or grounding. The non-compensated architecture gives designers control over stability-bandwidth tradeoffs. A compensation capacitor can be omitted or changed for unity-gain service, while larger values or added frequency compensation can improve stability in noise-gain configurations. With proper compensation, the manufacturer-reported capability includes a slew rate of up to 10 V/µs. This makes the LM201AN potentially useful where signal speed matters more than the compactness of a fixed-compensation amplifier. Typical applications include precision instrumentation amplifiers, logarithmic and summing amplifiers, active filters, transducers with relatively high source impedance, laboratory measurement systems, and low-frequency analog signal-conditioning chains. Its external compensation also permits optimization for different closed-loop gains rather than imposing one fixed stability profile across every application. When designing around the LM201AN, select the compensation network for the actual noise gain and verify closed-loop phase margin on the assembled board. Keep input and output return paths short, observe the device's specified supply and common-mode limits, and prototype compensation before high-volume production. External compensation makes the part flexible, but it also places a stability responsibility on the engineer. This page combines confirmed manufacturer-distributor data with clearly marked gaps, practical compensation guidance, package-aware replacement analysis, and procurement information. It distinguishes verified LM201AN characteristics from unverified specifications so engineers can make faster component-selection decisions without mistaking generic amplifier assumptions for device-specific facts.

RFQ Contact
LM201ANG - 1 MHz Non-Compensated Op Amp | onsemi
LM201ANG

LM201ANG - 1 MHz Non-Compensated Op Amp | onsemi

onsemi LM201ANG is a single, non-compensated general-purpose operational amplifier with a 1 MHz gain-bandwidth product, supplied in an 8-pin PDIP package. It allows the designer to select an external compensation capacitor suited to the required stability, bandwidth, and slew-rate performance. The device is identified as a precision single-channel amplifier for operation from -25°C to 85°C. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its two inputs. Its applications include analog signal conditioning, closed-loop gain stages, active filtering, integrators, and feedback control. Unlike an internally compensated amplifier, the LM201ANG leaves compensation to the user, providing greater flexibility where gain-bandwidth behavior must be optimized for a particular circuit. The LM201ANG combines a 1 MHz gain-bandwidth product with a single-amplifier configuration in a through-hole 8-pin PDIP package. Its non-compensated architecture requires an external compensation network to establish stable operation. The operating-temperature grade shown for this ordering code is -25°C to 85°C, making it suitable for conventional industrial and instrumentation environments within that temperature range. Because the amplifier is not internally compensated, its dynamic behavior depends strongly on the selected compensation capacitor, circuit topology, closed-loop gain, noise gain, and load. Designers should use the compensation guidance and typical application circuits in the manufacturer datasheet rather than treating the 1 MHz figure as a fixed, topology-independent operating bandwidth. The device can therefore support different stability and bandwidth compromises in precision analog circuits. Typical uses include low-frequency instrumentation amplifiers, active filters, sensor-conditioning channels, laboratory measurement equipment, and industrial control modules. The LM201ANG is especially relevant when an adjustable compensation capacitor provides more benefit than the simplicity of a unity-gain-stable internal compensation network. Its PDIP package also simplifies prototyping, inspection, and manual rework in low- to moderate-volume assemblies. When laying out a circuit, keep the compensation capacitor close to the compensation pin and use a short, low-inductance feedback path. Check stability across the intended gain, load, supply, and temperature ranges rather than relying only on a nominal simulation result. The principal engineering trade-off is that external compensation adds component selection and validation effort but permits optimization that an internally compensated amplifier cannot provide. This product page combines the exact ordering-code details, sourcing guidance, application context, and design considerations for the LM201ANG. It also distinguishes pin-compatible replacement options from devices that require a package change, helping engineers avoid a replacement that cannot be soldered into the existing footprint.

RFQ Contact
LM211-LM311 - Single High-Speed Differential Comparator
LM211-LM311

LM211-LM311 - Single High-Speed Differential Comparator

The Texas Instruments LM211-LM311 is a family designation for the LM211 and LM311 single high-speed differential comparators, designed for wide supply ranges from single 5 V operation through ±15 V split supplies. The LM211 and LM311 provide low input currents and open-collector outputs intended for driving lamps, relays, and logic-compatible loads. Their differential inputs can accept voltages outside the supply rails, while the output polarity and output-current requirements determine the external pull-up arrangement. A voltage comparator is a semiconductor device that compares two input voltages and switches its output according to their relationship. In the broader IC hierarchy, a comparator belongs to the analog signal-conditioning and interface family, alongside op-amps and logic interfaces. The LM211-LM311 family is useful when a design needs a threshold decision, overvoltage indication, level translation, or relay-drive function rather than linear analog amplification. The verified manufacturer material identifies the devices as single high-speed comparators with low input current. According to the Texas Instruments datasheet material supplied, the output levels are compatible with most TTL and MOS circuits, and the devices are capable of driving lamps or relays. The onsemi material additionally states that the inputs can be isolated from system ground while the output can drive loads referenced to ground, VCC, or VEE. These features support industrial control, instrumentation, and legacy interface designs. The family includes temperature and sourcing differences between LM211 and LM311 variants. The supplied Mouser datasheet excerpt specifies LM211 operation from −25°C to +85°C and LM311 operation from 0°C to +70°C for the referenced comparison. The same excerpt states that offset voltage, offset current, and bias-current specifications apply from a single 5 V supply up to ±15 V supplies, and that the positive input voltage limit is 30 V above the negative supply. Exact ordering codes and package-specific electrical limits require the relevant manufacturer datasheet and suffix. Typical uses include sensing a control voltage against a reference, detecting an overvoltage condition, switching a relay when a sensor crosses a threshold, and interfacing an analog signal to TTL or MOS logic. Because the output is open collector, a pull-up resistor is generally required. The pull-up must be selected against the required sink current, output voltage, speed, and system supply constraints. The principal design consideration is ensuring that input common-mode voltage, supply voltage, output pull-up, and input/output isolation meet the particular LM211 or LM311 ordering variant. The family designation alone does not identify a unique package, suffix, temperature grade, or exact parameter set. Use the manufacturer datasheet linked on this page before committing a footprint or substituting a part. This page consolidates the verified manufacturer descriptions, practical comparator usage guidance, and the available cross-reference information. It distinguishes confirmed family-level facts from ordering-code-specific data that is not established by the supplied search results.

RFQ Contact
LM211D - Single Differential Comparator with Strobe | Texas Instruments
LM211D

LM211D - Single Differential Comparator with Strobe | Texas Instruments

The Texas Instruments LM211D is a single differential comparator with strobes that operates from wide-ranging power supplies, including ±15 V operational-amplifier rails and 5 V logic systems. Its open-collector output is compatible with most TTL and MOS circuits, and the device can drive lamps or relays. The LM211D is supplied in an 8-pin SOIC package, with an operating temperature range of -40°C to +85°C. A differential comparator is an integrated circuit that compares two input voltages and changes its output state according to their relative polarity. It belongs to the comparator hierarchy within analog and interface semiconductors: differential comparator → voltage comparator → analog interface IC → semiconductor. Unlike a general-purpose operational amplifier, the LM211D provides a saturated, logic-oriented output intended for threshold detection and switching rather than linear amplification. The LM211 family is described by Texas Instruments as a single high-speed voltage comparator. Its differential inputs allow a circuit to establish a switching threshold with an external reference, while the strobe function provides control over when the internal output participates in state changes. The open-collector architecture supports wired-interface and pull-up arrangements, although the required pull-up component and its implementation details are not included in the supplied source snippets. The LM211D uses logic-compatible output levels that can interface with TTL and MOS logic. This makes it suitable for translating an analog decision into a digital control signal. The manufacturer specifically identifies lamp and relay driving as supported applications, although the exact current limits, output sink-current ratings, response times, input common-mode limits, and input offset voltage were not present in the retrieved data and must be confirmed in the complete manufacturer datasheet before a final design is released. Typical uses include sensing a voltage crossing a reference level, detecting the state of a sensor or timing signal, driving digital control logic, and operating lamp or relay interfaces. In a practical circuit, the two inputs receive the signal and threshold voltages, the output uses an appropriate pull-up arrangement for open-collector operation, and the strobe pin is connected so the application can either enable or disable normal comparison behavior as required. The primary design consideration is to verify the complete electrical limits and pin functions from the official LM211 datasheet before layout sign-off. Designers should pay particular attention to input common-mode range, output current, supply sequencing, open-collector pull-up voltage, and strobe logic because these values were not included in the retrieved snippets. The 8-pin SOIC footprint also requires adequate spacing between adjacent pins for soldering and inspection. This page consolidates verified manufacturer and distributor information, cross-brand sourcing references, package details, selection guidance, and application-specific engineering considerations. It also clearly separates confirmed LM211D characteristics from parameters that still require datasheet verification, providing a useful basis for early component selection without replacing the authoritative manufacturer documentation.

RFQ Contact
LM211DG - 200 ns Single Comparator | onsemi | SOIC-8
LM211DG

LM211DG - 200 ns Single Comparator | onsemi | SOIC-8

onsemi LM211DG is a single high-speed voltage comparator with a 200 ns response time, 5 V to 30 V single-supply operation, and an open-collector output in an 8-pin SOIC package. It can also operate from split supplies, including ±15 V rails commonly used with operational amplifiers. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input crosses the other. The LM211 belongs to the broader comparator, analog IC, and semiconductor hierarchy. Its open-collector output can interface with TTL, MOS, DTL, and RTL logic, while its ability to accept split supplies makes it useful in systems that do not share a common signal ground. Key features include one comparator channel, a 200 ns response time, and operation across a 5 V to 30 V single-supply range. The open-collector output provides a flexible way to drive compatible digital logic, lamps, or relays when an appropriate pull-up arrangement is used. The specified operating temperature range for LM211DG is -25°C to 85°C. The LM211 architecture is designed for high-speed threshold detection rather than precision amplification. Its input stage can operate independently of system ground, which helps when comparing signals referenced to a different potential. The open-collector output remains in a high-impedance state unless pulled down, allowing the output transition speed to depend partly on the external pull-up resistor and associated capacitance. Typical applications include industrial control interfaces, pulse-width and timing circuits, sensor threshold detection, relay or lamp drive, level translation between analog and digital systems, and general-purpose logic interfacing. The combination of a 200 ns response time and flexible supply options also suits pulse-width measurement and fast event detection circuits. When designing around the LM211DG, account for the open-collector output when calculating rise time and fanout. Keep input and output paths short, use a pull-up resistor appropriate for the driven logic family, and check input common-mode limits for the selected supply configuration before finalizing the schematic. This product summary combines the LM211DG electrical envelope, package information, sourcing context, pin-compatible alternatives, and practical interface guidance. It supports faster component selection by separating core operating characteristics from application-specific design considerations.

RFQ Contact
LM211DR - 115ns Differential Comparator | Texas Instruments
LM211DR

LM211DR - 115ns Differential Comparator | Texas Instruments

Texas Instruments LM211DR is a single high-speed differential comparator with a 115 ns response time, a 3.5 V to 30 V supply-voltage range, and an 8-pin SOIC package. Its open-collector or open-emitter output is compatible with common TTL and MOS logic levels, while its differential inputs support threshold and window comparisons. A voltage comparator is an analog signal-processing IC that compares two input voltages and changes its output state when the difference crosses a defined threshold. In the electronic-component hierarchy, an LM211 comparator belongs to the comparator category, then to analog interface ICs, and ultimately to integrated circuits. It provides a decision function between sensors, transducers, dividers, and digital control logic without converting the compared quantity into a coded data stream. The LM211 family operates from wide supply ranges, including positive 5 V logic systems and positive or negative 15 V analog supplies. Its high-speed response supports decisions that must occur quickly, while the open-collector output can interface with TTL and MOS circuits and drive loads such as lamps or relays. These characteristics make it useful when a logic system needs a fast threshold event rather than a continuous analog voltage. The differential input arrangement permits comparison of two changing voltages rather than one signal against ground alone. Input offset and common-mode limits remain important when selecting the input operating region, and the supply voltage must remain within the stated 3.5 V to 30 V range. Because the output stage is open-collector or open-emitter, an external pull-up resistor is generally required to establish a valid high output level in a wired logic interface. Typical LM211DR applications include sensor threshold detection, pulse-width and timing comparisons, industrial control interfaces, lamp or relay drive with suitable interface circuitry, and general-purpose logic conditioning. The 115 ns response time is especially useful where the comparator serves as a fast boundary detector between an analog node and a digital control system. In a practical circuit, place the comparator close to the signals being compared, route high-impedance input nodes carefully, and provide stable bypassing for the supply pins. Add the pull-up component required by the open-collector output stage and verify that relay, lamp, or other inductive loads are isolated or protected from transients. This product page combines manufacturer application guidance, package and timing details, orderable alternatives, and implementation-focused design notes. It also organizes the LM211DR for engineers who need to understand its logic compatibility, supply requirements, replacement choices, and PCB-level constraints before beginning a board design.

RFQ Contact
LM211DR2G - Single 5-30V Comparator | onsemi
LM211DR2G

LM211DR2G - Single 5-30V Comparator | onsemi

The onsemi LM211DR2G is a single general-purpose voltage comparator designed for operation from a 5 V to 30 V single supply or split supplies of ±15 V. It provides a 200 ns response time and is packaged in an 8-pin SOIC. The comparator supports open-collector output operation, allowing its output state to be pulled up to a suitable supply or load reference while providing a compatible interface for DTL, MOS, open-emitter, open-collector, RTL, and TTL circuits. A voltage comparator is an analog signal-conditioning component that compares two input voltages and produces a logic-level output indicating which input is higher. Comparators belong to the broader amplifier and comparator hierarchy, where they sit between sensor or measurement inputs and digital control logic. Unlike an operational amplifier intended primarily for linear amplification, the LM211 is optimized for rapid, direct threshold decisions, making it useful in industrial control, sensing, protection, and switching interfaces. Key features include a single-comparator configuration, a 5 V to 30 V supply range, a 200 ns response time, and an operating temperature range of -25 °C to +85 °C. Its open-collector output provides flexible pull-up placement and permits the output to drive lamps, relays, and other loads referenced to ground, VCC, or VEE. These characteristics make the device useful where a logic decision must be translated into an actionable system output. The LM211 architecture supports input voltages that are isolated from system ground when split supplies are used. This allows the comparator inputs to monitor signals in systems that also use negative rails. The output topology is flexible rather than tied to only one fixed supply, which helps engineers construct level-shifting, isolation, and relay-driving circuits without changing the comparator package or footprint. Typical applications include industrial sensor thresholding, overvoltage and undervoltage detection, relay activation, lamp control, window or level comparators, and interfaces between analog measurement circuitry and TTL or MOS logic. The 200 ns response time is also suitable for moderate-speed control loops where delayed comparison would reduce system responsiveness. Designers should account for input common-mode range, output pull-up requirements, supply decoupling, and permissible output current when laying out the circuit. Place the device close to the driven logic and route the open-collector output away from sensitive analog inputs to reduce switching transients. Use a suitable pull-up resistor for TTL or MOS interfacing, and verify that the selected load does not exceed the output sink-current limits. This page combines the principal operating characteristics, practical implementation guidance, compatible alternatives, and application context for faster component selection.

RFQ Contact
LM211DRE4 - 115 ns Differential Comparator | Texas Instruments
LM211DRE4

LM211DRE4 - 115 ns Differential Comparator | Texas Instruments

Texas Instruments LM211DRE4 is a single differential voltage comparator with strobe inputs, 115 ns response time, and an 8-pin SOIC package. The device operates from 3.5 V to 30 V, supports single-supply operation from 5 V to 30 V or split supplies up to ±15 V, and provides an open-collector output compatible with TTL, MOS, DTL, and RTL logic. Its operating temperature range is -40°C to 85°C. A voltage comparator is an analog interface IC that compares two input voltages and produces a logic-level output indicating which input is higher. The comparator belongs to the broader hierarchy of analog comparator, analog IC, and semiconductor. Unlike a general-purpose operational amplifier, the LM211DRE4 is optimized for fast threshold decisions, regenerative switching behavior, and direct interface with digital logic systems. The LM211 family combines a differential input stage with an open-collector output and dedicated strobe control. Its 115 ns propagation response supports rapid level detection, while its wide supply range allows operation from ±15 V analog systems as well as 5 V logic rails. The open-collector output can sink logic-level current and can be pulled up for wired logic, relay interfaces, or lamp-driving arrangements. The comparator's inputs can operate independently of system ground when split supplies are used, providing useful flexibility in legacy industrial and instrumentation circuits. Output levels are compatible with most TTL and MOS circuits, reducing the need for intermediate logic drivers. Two strobe inputs support latch-like control in test equipment, pulse-width systems, and switching networks where the output state must be actively enabled or disabled. Typical applications include industrial control and automation, power-supply supervision, signal threshold detection, test and measurement instrumentation, relay or lamp interfaces, and legacy digital logic interfaces. The 8-pin SOIC package supports through-hole assembly and PCB layouts based on the standard SOIC footprint. The broad supply range also makes the device suitable for systems transitioning between older ±15 V equipment and newer single-rail electronics. Designers should verify output pull-up voltage, sink current, input common-mode range, and strobe logic levels for the intended system. Because the output is open collector, an external pull-up resistor is normally required. Keep the comparator close to the sensed signal and logic interface to reduce susceptibility to noise and propagation-delay variation on long traces. This page combines manufacturer specifications, practical circuit guidance, comparison parameters, and pin-compatible replacement information. It also distinguishes true drop-in options from related devices that require different output, timing, supply, or qualification behavior, helping engineers choose a replacement without overlooking circuit-level compatibility.

RFQ Contact
LM211DRG4 - High-Speed Differential Comparator | Texas Instruments
LM211DRG4

LM211DRG4 - High-Speed Differential Comparator | Texas Instruments

Texas Instruments LM211DRG4 is a single high-speed differential comparator with strobe control, supplied in an 8-pin SOIC package. The device operates from a 5 V supply as well as positive and negative supplies up to ±15 V, and its output is compatible with common TTL and MOS logic levels. The LM211 family can also drive lamps or relays, making it suitable for threshold detection, pulse shaping, and interface conversion. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference between them crosses a defined threshold. It belongs to the comparator hierarchy, which includes general-purpose comparators, differential comparators, and interface ICs. Compared with a general-purpose op-amp, a comparator provides faster threshold-oriented switching and an output stage designed to connect more directly to digital logic, lamps, or relays. The LM211 family combines single-comparator architecture with broad supply-voltage support. A 5 V implementation simplifies compatibility with TTL and MOS logic, while split or dual supplies support ±15 V industrial and analog systems. The strobe input provides a way to inhibit output transitions during selected operating intervals, and the open-collector output permits external pull-up selection and wired-interface functions. The LM211DRG4 is specified for operation from -40°C to 85°C and uses the TI D package, an 8-pin surface-mount SOIC. The open-collector output is important because it allows the output voltage, rise time, and sink current to be adapted with an external pull-up resistor. It can directly support compatible logic families when the pull-up voltage and resistor are selected correctly. However, an open-collector output cannot source current independently, so the external pull-up is required in normal operation. Designers should also account for the propagation interval around the strobe control when timing system-level events. Typical uses include zero-crossing detection, overvoltage and undervoltage monitoring, industrial control interfaces, relay or lamp drivers, and signal conditioning where a logic-level indication is required. The comparator can operate from 5 V in a logic-control board or from higher positive and negative rails when the monitored signals exceed single-supply limits. Its wide supply range allows one device family to serve multiple industrial and instrumentation architectures. For robust layouts, keep the input traces short, place the output pull-up close to the comparator, and provide adequate ground-return paths. Do not allow floating input nodes during power transitions; use input bias resistors when necessary. Review the manufacturer datasheet for input common-mode limits, output sink-current limits, supply-current behavior, and absolute maximum ratings before operating the LM211DRG4 near its supply limits. This page combines the exact LM211DRG4 ordering information with package, pinout, application, replacement, and design guidance. It also identifies same-footprint alternatives for design review while keeping separate the device's verified electrical limits and the practical conditions that determine whether it is suitable for a particular system.

RFQ Contact
LM211DT - 200 ns Voltage Comparator | STMicroelectronics
LM211DT

LM211DT - 200 ns Voltage Comparator | STMicroelectronics

STMicroelectronics LM211DT is a single general-purpose voltage comparator with a response time of 200 ns, low input current, and open-collector output. It is packaged in an 8-pin SOIC and operates from single 5 V supply to dual ±15 V supplies. The LM211 family is designed for precision threshold detection across industrial control, instrumentation, and logic-interface systems. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the differential input crosses a selected threshold. In the broader semiconductor hierarchy, the LM211DT belongs to the comparator class, analog IC category, and power-management and signal-conditioning application ecosystem. Unlike an operational amplifier, the device is optimized for fast switching behavior and logic-compatible output drive rather than linear amplification. The principal features of the LM211DT include low input current, a 200 ns propagation delay, and an output compatible with TTL, DTL, RTL, MOS, and open-collector or open-emitter logic. Its open-collector output can sink logic-level current while the output transistor remains off, making pull-up placement and system-level bus design important. The wide supply-voltage range supports both traditional analog rails and modern single-supply logic systems. Internally, the comparator provides adjustable sensitivity because the output transition can be affected by the voltage difference between its non-inverting and inverting inputs. The STMicroelectronics datasheet also identifies a strobe control, allowing the designer to inhibit or enable output transitions according to system timing. Low input current is particularly useful when the comparator monitors high-impedance sensors, divider networks, or analog front ends where input bias current could shift the comparison threshold. Typical applications include industrial sensor threshold detection, overvoltage and undervoltage supervision, relay or solenoid drive, window-comparator circuits, level translation, and conditioning slow sensor signals into fast logic events. The open-collector output is useful in systems that require wired logic, pull-up-controlled buses, or a fail-safe output state when the device is unpowered. The primary design consideration is output topology. Place the required pull-up resistor from OUT to the positive logic rail, account for the maximum sink current, and use the STROBE pin according to the required timing. Check input common-mode range, supply polarity, output pull-up voltage, and propagation-delay requirements across the complete temperature range before treating a nominal 200 ns figure as sufficient for the application. This page combines the LM211DT electrical characteristics, package information, comparison options, and application guidance into an engineering-focused reference. It also highlights practical distinctions between the comparator's low-current inputs, wide supply range, strobe function, and open-collector output so that selection is based on circuit behavior rather than part number alone.

RFQ Contact
LM211N - Wide-Supply Voltage Comparator | STMicroelectronics
LM211N

LM211N - Wide-Supply Voltage Comparator | STMicroelectronics

The STMicroelectronics LM211N is a single, general-purpose voltage comparator supplied in an 8-pin DIP package. It is designed for operation from single +5 V logic supplies through ±15 V analog supplies, with compatible output levels for common TTL and MOS logic circuits. The verified distributor record identifies the LM211N as a standard comparator with DTL, MOS, open-collector, open-emitter, RTL, and TTL compatibility. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-oriented output indicating which input is higher. In the broader semiconductor hierarchy, the LM211N belongs to the comparator class within analog and mixed-signal ICs. Its open-collector output architecture is useful when the next stage needs a pull-up supply or when multiple devices must share a wired bus. The verified manufacturer-related results identify the LM111, LM211, and LM311 family as single high-speed voltage comparators designed for a wide range of supply voltages. The TI family description specifically highlights operation from ±15 V operational-amplifier supplies and 5 V logic supplies, while the ST result identifies low input currents and wide supply-voltage operation. The LM211N’s general-purpose comparator function supports threshold detection, sensing, switching, and control tasks. The STMicroelectronics result describes the device as usable with standard ±15 V operational-amplifier supplies and single +5 V logic supplies. Its output is compatible with many TTL and MOS circuits, and it is capable of driving lamps or relays according to the verified TI family description. The exact STMicroelectronics LM211N electrical limits, timing values, input-offset figures, output-current limits, and temperature-grade details were not included in the supplied source snippets and are marked for data completion. Typical applications include 5 V logic interfacing, relay or lamp drive, threshold crossing detection, industrial control, instrumentation, and systems where a comparator must operate across positive or split analog supplies. Because this product is an analog-to-logic decision element rather than a power device, SOA data is not applicable. The 8-DIP package is through-hole and is suited to legacy industrial, educational, prototype, and repair assemblies. The principal design consideration is confirming the complete pinout, supply limits, input common-mode range, output pull-up arrangement, and timing limits from the manufacturer datasheet before replacing another LM211-family device. The supplied web results confirm the functional family and package category, but do not provide enough numeric detail to claim a fully qualified cross-brand drop-in replacement. Compare the DIP footprint, pin numbering, open-collector output, input arrangement, supply range, and propagation delay before substitution. This page consolidates verified distributor and manufacturer-family information, identifies the LM211N’s comparator role and package category, and records missing technical values rather than guessing them. For a production replacement, use the official LM211N datasheet and validate every device-specific limit on the intended PCB.

RFQ Contact
LM211P - High-Speed Voltage Comparator | Texas Instruments
LM211P

LM211P - High-Speed Voltage Comparator | Texas Instruments

The Texas Instruments LM211P is a single high-speed differential voltage comparator in an 8-PDIP package, operating from single 5 V supplies through split ±15 V supplies. It provides an open-collector output compatible with TTL and MOS logic and is capable of driving lamps and relays. The verified distributor data identifies a 115 ns response time, 3 mV input offset voltage, 100 nA input bias current, 6 µA typical input current, and a 106.02 dB gain-bandwidth figure. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input crosses the other. The LM211P belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where it bridges precision analog sensing and digital logic control. Its differential inputs support sensing of a sensor signal relative to a reference, while its open-collector output provides a flexible interface to pull-up-based digital systems. The principal benefits are low input offset voltage, low input bias current, fast response, broad supply compatibility, and logic-level output compatibility. Its open-collector output can sink current from an external pull-up while remaining in an electrically inactive high-impedance state when turned off. This architecture is useful when the output must control a relay, lamp, indicator, or interface with a higher-voltage pull-up supply. The 8-PDIP through-hole package also simplifies prototyping, inspection, and repair in laboratory and industrial control systems. The LM211, LM111, and LM311 form a related high-speed comparator family. The LM211P is suitable for dual-supply operation around ±15 V and single-supply operation beginning at 5 V. Its inputs can be isolated from system ground, while the output can be referenced through its pull-up arrangement to ground, VCC, or another suitable rail. This flexibility is important when the sensed signal and logic interface use different voltage domains. Typical applications include overvoltage and undervoltage detection, sensor threshold conditioning, industrial control interfaces, relay activation, lamp indication, and conversion of analog events into logic-compatible signals. In such systems, the non-inverting input may receive a reference voltage and the inverting input may receive a feedback or sensor voltage, or the inputs may be reversed depending on the required switching polarity. The external pull-up resistor should be selected for the desired logic family and output current. A key design consideration is the strobe and output arrangement. The strobe pins are used for gating or inhibit control, while the open-collector output requires an external pull-up. Designers should verify input common-mode limits, supply polarity, pull-up voltage, output sink current, and logic thresholds for the specific system rather than relying only on nominal logic compatibility. This page consolidates verified manufacturer information, distributor pricing, pin-level guidance, application context, and strictly filtered drop-in alternatives. It distinguishes verified LM211 family options from mere functional equivalents and highlights the electrical checks required before replacing an original 8-pin comparator in an existing design.

RFQ Contact
LM211PW - Single Strobed Differential Comparator | Texas Instruments
LM211PW

LM211PW - Single Strobed Differential Comparator | Texas Instruments

The Texas Instruments LM211PW is a single strobed differential comparator with open-collector and open-emitter outputs, operating from wide supply voltages that include ±15 V and 5 V systems. It is packaged in an 8-pin TSSOP (PW) package. A differential comparator is an analog integrated circuit that compares two input voltages and produces a logic-oriented output indicating which input is higher. The LM211 belongs to the comparator and analog IC hierarchy, where it bridges an analog sensing function and downstream TTL, MOS, lamp, or relay control. Its strobe input allows the output state to be controlled for system timing, testing, or synchronization. The verified product information identifies the LM211PW as a single high-speed voltage comparator with strobe capability, open-collector and open-emitter outputs, and compatibility with most TTL and MOS circuits. Texas Instruments describes the LM111, LM211, and LM311 family as capable of driving lamps or relays and operating across a broad power-supply range. The PW package is identified as an 8-pin TSSOP. The open-collector and open-emitter outputs make output-state control and external pull-up or pull-down implementation important. The comparator is suitable for threshold detection, level translation, relay or lamp interfaces, industrial control logic, and mixed-signal systems where a decision is based on the relationship between two voltages. Its logic compatibility allows the output to interface with digital systems when appropriate external components are used. Typical applications include sensing a control voltage against a reference, detecting an overvoltage or undervoltage condition, generating a system enable signal, and switching a relay or lamp from a low-voltage control circuit. The LM211PW should be selected when a differential comparison function, wide supply-voltage support, strobe control, and an 8-pin TSSOP are required. Exact electrical ratings, pin behavior, output ratings, and recommended operating limits should be confirmed from the manufacturer datasheet before design release. The LM211PW datasheet is the authoritative source for pin assignments, voltage ranges, input common-mode behavior, output sink and source capabilities, timing characteristics, and application guidance. Verify the absolute maximum ratings, supply sequencing, input protection, output pull-up requirements, and external drive-current limits for the intended load. Do not assume that an open-collector output can source current without an appropriate pull-up or active external network. This product data combines the verified Texas Instruments product identity, distributor catalog information, package details, comparator function, and application-relevant guidance. It is intended to support component search, engineering selection, and design review while avoiding unverified electrical values that are not present in the supplied source material.

RFQ Contact