Products (44,000+)

LM2903DG4 - Dual Open-Collector Comparator | Texas Instruments
LM2903DG4

LM2903DG4 - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903DG4 is a dual differential comparator containing two independent comparator channels, an open-collector output configuration, and an 8-pin SOIC package. The device supports single-supply or dual-supply operation, with a maximum-rated supply voltage of 32 V and a tested differential input voltage of 30 V. Its low supply-current drain of 0.4 mA typical per comparator is independent of supply voltage, making it suitable for power-conscious industrial and embedded systems. A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital logic state indicating which input is higher. The LM2903 is a dual differential comparator, placing two independent comparator channels in one package. Within the broader semiconductor hierarchy, it is a comparator, analog IC, and interface/amplifier-class signal-conditioning component used to translate small analog voltage relationships into logic-compatible decisions. Each LM2903 channel supports operation from a single supply or from dual supplies. The open-collector outputs can sink output current while presenting a high-impedance state when the output is inactive. According to the Texas Instruments LM2903 product information, the outputs are compatible with TTL, MOS, and CMOS logic. This makes the device useful when an external pull-up resistor is required to establish the inactive output voltage. The two channels are electrically independent, allowing one comparator to monitor a control threshold while the other handles a second signal, alarm, or protection event. Common-mode input voltage range includes ground, and the differential input rating equals the maximum-rated supply voltage. These characteristics support sensing arrangements in which signals may approach the lower supply rail, subject to the limits stated in the manufacturer datasheet. Typical applications include overvoltage and undervoltage detection, industrial sensor interfaces, battery monitoring, window or threshold detection, relay-control logic, and general-purpose signal conditioning. The wide supply range also makes the device useful in 5 V, 12 V, and 24 V industrial systems when the relevant operating limits are observed. Designers should account for open-collector pull-up requirements, input common-mode limits, output sink-current capability, and unused-channel handling. A pull-up resistor must be selected to establish a valid logic-high voltage without exceeding the device's output-current limits. Input filtering may also be required when noisy signals could cause repeated transitions near the comparison threshold. This page combines manufacturer identification, package details, cross-reference information, and engineering guidance for threshold detection and open-collector interface design. It also highlights the operating conditions that should be checked before using a substitute or family variant on an existing board.

RFQ Contact
LM2903DGKR - Dual Open-Collector Comparator | Texas Instruments
LM2903DGKR

LM2903DGKR - Dual Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903DGKR is a dual differential comparator with two independent comparison channels, open-collector outputs, and rail-to-rail input capability in an 8-pin VSSOP package. The device operates from 2 V to 36 V, supports common-mode input voltages from -1 V to +18 V, and has a typical response time of 1.3 microseconds. It is intended for general-purpose voltage comparison, threshold detection, and interface applications. A comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. In the broader semiconductor hierarchy, LM2903 belongs to the comparator and linear IC family, where it bridges analog signal sensing and digital control. Each LM2903 channel combines a differential input pair with an open-collector output, allowing the output stage to pull a logic rail low when the comparison state requires it. The LM2903DGKR provides two channels in one package, reducing board area compared with separate single comparators. Its open-collector outputs support wired-AND behavior when multiple channels pull a shared bus low, while external pull-up resistors establish the high logic voltage. Rail-to-rail input capability extends the usable common-mode range toward the supply rails, which is useful in battery-powered and low-voltage systems. Its stated 1.3-microsecond response time supports general-purpose detection rather than high-speed timing applications. The operating range of 2 V to 36 V makes the device suitable for low-voltage control circuits and higher-voltage industrial systems. Common-mode operation from -1 V to +18 V permits signal sensing beyond the lower supply rail. Each output remains electrically open at the collector, so designers can select pull-up voltage, interface to open-drain logic, or connect several outputs to a shared bus. The 8-pin VSSOP package supports compact surface-mount layouts but requires careful handling because its lead pitch is narrower than that of standard SOIC packages. Typical uses include DC overvoltage and undervoltage detection, sensor-threshold conditioning, industrial control inputs, battery monitoring, and open-drain logic interfacing. In each case, resistor values should be chosen from the applied input range, output pull-up requirement, output leakage, and permissible sink current rather than from a single fixed rule. When laying out an LM2903DGKR circuit, place input and output components close to their associated pins and keep switching-current paths away from the differential inputs. Add a local supply bypass capacitor to limit transient coupling into the comparison threshold. The open-collector output also requires a pull-up resistor in every configuration where a valid high output is required. This product record combines the manufacturer ordering information, package and functional characteristics, verified replacement candidates, and practical layout guidance. It is intended to help engineers evaluate LM2903DGKR for open-collector comparator designs while accounting for voltage range, response time, channel count, and board-space constraints.

RFQ Contact
LM2903DGKRG4 - 36V Dual Comparator | Texas Instruments
LM2903DGKRG4

LM2903DGKRG4 - 36V Dual Comparator | Texas Instruments

Texas Instruments LM2903DGKRG4 is a dual differential comparator containing two independent voltage comparators, with a 2 V to 36 V supply range, approximately 300 ns response time, and an 8-pin VSSOP package. Both channels use open-collector outputs, allowing wired logic or use with an external pull-up resistor. The part supports single-supply operation and dual-supply operation when the total supply span is 2 V to 36 V. A voltage comparator is an analog interface that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the comparator hierarchy, where a comparator is an analog IC used for threshold detection, signal conditioning, and protection. Its two independent channels can monitor separate control, sensing, or feedback signals, while its open-collector architecture provides flexible interface voltage selection. The principal operating characteristics include a 2 V to 36 V supply range, approximately 300 ns propagation delay, and low supply-current drain of 0.4 mA typical per comparator. Its rail-to-rail input capability allows the input common-mode range to extend toward the supply rails. Open-collector outputs can sink output current while leaving the effective pull-up voltage under the system designer’s control, making the device useful in wired-AND, wired-OR, and level-shifting arrangements. Each channel has one inverting input, one non-inverting input, one output, and access to the supply and ground rails. Because the two comparators are independent, each channel can be configured for a different threshold or polarity. Input offset, input bias current, output saturation characteristics, and detailed common-mode behavior should be checked against the manufacturer datasheet for each operating condition, particularly when sensing near a supply rail. Typical uses include industrial control systems, battery-powered equipment, power-supply sequencing, overvoltage and undervoltage monitoring, sensor-threshold conditioning, and general-purpose logic interfaces. The wide supply range accommodates multiple industrial and automotive-style voltage environments, while the low typical supply-current drain is advantageous in portable systems. An open-collector output also allows multiple comparators to share a pull-up node when wired logic is required. The primary design consideration is the open-collector output. Every output requires a suitable pull-up resistor and account for sink-current limits, rise time, bus capacitance, and the logic threshold of the receiving device. Input filtering may also be necessary when noisy analog signals are compared, while board placement should keep comparison inputs away from switching nodes and high-current return paths. This page combines the exact ordering designation with package, pin, application, and drop-in replacement guidance to support schematic review and PCB reuse. It also provides practical design notes for pull-up selection, input conditioning, and open-collector interfacing, helping engineers evaluate the LM2903 family beyond a basic datasheet parameter summary.

RFQ Contact
LM2903DMR2 - Dual Precision Comparator, 36 V | onsemi
LM2903DMR2

LM2903DMR2 - Dual Precision Comparator, 36 V | onsemi

onsemi LM2903DMR2 is a dual independent precision voltage comparator designed for single-supply or split-supply operation, with a supply range extending to 36 V and an 8-pin SOIC package. The device compares two input voltages per channel and provides an open-collector output suitable for wired logic-level comparison and system monitoring. A voltage comparator is an analog integrated circuit that evaluates two input voltages and changes its output state according to their relationship. The LM2903 belongs to the comparator hierarchy within analog signal-processing and interface ICs. Its two independent channels allow a single package to monitor two unrelated signals, while single- or split-supply operation makes it useful across industrial, automotive, and embedded power-control systems. The LM2903 series provides a common-mode input range that extends to ground under single-supply operation. This characteristic is important when a monitored signal can approach 0 V. The low-offset-voltage designation indicates that the comparators are intended to detect relatively small differential voltages, although the exact offset limits depend on the operating conditions specified in the onsemi datasheet. Each channel operates independently, allowing different threshold networks and signal pairs to share the package. The device supports supply voltages up to 36 V, which provides headroom for industrial and automotive environments. Its comparator outputs are designed for interfacing with conventional logic, although output topology, sink-current limits, and pull-up requirements must be confirmed from the manufacturer datasheet before final circuit design. Typical uses include power-supply sequencing, battery and charger threshold detection, overvoltage and undervoltage protection, window monitoring, sensor-level detection, and general signal conditioning. In a power system, the two channels can monitor independent rails or compare a feedback voltage against a reference. The open-collector-style interface also allows multiple devices to share a pull-up arrangement when the required bus architecture and current limits are appropriate. When laying out the circuit, keep comparator input nodes short and shield them from switching nodes and high-current paths. Confirm whether the selected output configuration requires an external pull-up resistor, and use that resistor to satisfy the downstream logic's rise-time requirements. Check supply-decoupling placement at the device pins and verify input and output limits for the complete temperature range. This product record combines the LM2903DMR2 electrical description, verified source links, same-package alternatives, application guidance, and design checks to support faster component selection and PCB-level engineering decisions.

RFQ Contact
LM2903DMR2G - Dual Low Offset Voltage Comparator | onsemi
LM2903DMR2G

LM2903DMR2G - Dual Low Offset Voltage Comparator | onsemi

The onsemi LM2903DMR2G is a dual independent precision voltage comparator with 2 mV typical input offset voltage, 1.3 us typical response time, and a wide 2 V to 36 V supply range, housed in an 8-pin MSOP (Micro8) surface-mount package. A voltage comparator is an analog building block that compares two input voltages and drives its output to indicate which input is higher. Comparators form the lowest tier of the amplifier IC hierarchy (comparator -> amplifier IC -> analog signal chain IC -> semiconductor) and differ from op-amps by their open-collector outputs and fast, unsaturated switching behavior. The LM2903 belongs to the industry-standard LM393 comparator family, which has been the default choice for level detection, threshold monitoring, and limit sensing across consumer, automotive, and industrial electronics for decades. Key features include low input offset voltage as low as 2.0 mV, input common-mode range extending down to ground (V-) level even under single-supply operation, low supply current of approximately 700 uA per package, and open-collector outputs compatible with TTL, MOS, and CMOS logic levels. The wide 2 V to 36 V single-supply range (or equivalent split-supply operation) allows direct connection to automotive 12 V and industrial 24 V rails without preconditioning. Architecturally, the device integrates two fully independent comparator channels that share only the supply pins, permitting simultaneous use without channel-to-channel interaction. The open-collector output stage requires an external pull-up resistor, which lets designers set the logic interface level independently of the supply - a 5 V pull-up on a 12 V-powered comparator interfaces directly with TTL logic. Typical applications include limit comparators and threshold detectors in power supplies, window comparators in battery chargers and over-voltage protection circuits, sensor conditioning for industrial automation, and level translation and oscillator timing circuits in consumer electronics. A key design consideration: because the output is open-collector, forgetting the pull-up resistor produces a permanently floating output; select the pull-up value for the required rise time and sink current, typically 3 k to 15 k. Also keep input differential voltage within the absolute maximum rating. This page consolidates verified electrical specifications, drop-in alternatives, application guidance, and practical design notes not found in a single manufacturer document.

RFQ Contact
LM2903DR - Dual Open-Collector Comparator | Texas Instruments (Tape & Reel)
LM2903DR

LM2903DR - Dual Open-Collector Comparator | Texas Instruments (Tape & Reel)

The Texas Instruments LM2903DR is a dual differential analog comparator with two independent comparator channels, an operating supply range of 2 V to 36 V, a response time of 300 ns, and an 8-pin SOIC package. Each channel provides open-collector output behavior for level translation, relay driving, and wired-AND logic functions. The device is specified for operation from -40 °C to +125 °C according to the available manufacturer comparison data. An analog comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM2903DR belongs to the comparator hierarchy within analog and mixed-signal semiconductors, providing a simple alternative to an operational amplifier configured as a comparator. Its two channels operate independently, allowing one package to implement two threshold decisions or to control complementary functions in a single circuit. The open-collector outputs are a defining electrical feature. Each output transistor can pull its output low, but it cannot actively drive the output high, so an external pull-up resistor is required. Multiple open-collector outputs can share one pull-up to create a wired-AND arrangement. This architecture also provides a useful form of output isolation while remaining compatible with standard 5 V and 3.3 V digital logic levels when the pull-up rail is selected appropriately. The 2 V to 36 V supply capability allows operation from low-voltage analog systems through conventional industrial control rails. Its 300 ns response time supports applications where decisions must be made faster than typical slow comparators but where nanosecond-level precision is unnecessary. The operating temperature range covers industrial environments, although production designs should still verify temperature-dependent input offset, output-current, and propagation-delay behavior using the selected manufacturer's complete datasheet. Typical uses include industrial sensor conditioning, battery monitoring, overvoltage detection, window or level comparators, relay and solenoid interfaces, and digital control systems that require open-collector outputs. The SOIC-8 package is also appropriate for through-hole-style PCB assembly and manual rework, although SOIC-8 is larger than modern comparator packages such as SOT-23 and MSOP-8 variants. When designing with the LM2903DR, always place the input and pull-up networks close to their associated pins, and account for input common-mode limits at the selected supply voltage. A pull-up resistor is not optional because the open-collector output cannot source current. Reviewing the voltage drop across the pull-up and the output transistor's current rating is essential when several outputs share the same node. This page consolidates verified distributor listings, manufacturer references, pin-compatible alternatives, package details, and practical circuit guidance. It also distinguishes directly interchangeable devices from higher-speed or higher-precision alternatives whose electrical behavior may require different design assumptions.

RFQ Contact
LM2903DR2 - Dual 36 V Comparator | onsemi | SOIC-8
LM2903DR2

LM2903DR2 - Dual 36 V Comparator | onsemi | SOIC-8

onsemi LM2903DR2 is a dual differential voltage comparator designed for single-supply or split-supply operation between 2 V and 36 V. The device contains two independent comparison channels, supports a common-mode input range extending to ground in single-supply systems, and is packaged in an 8-pin SOIC. Its open-collector output architecture provides flexible interface options for wired logic, pull-up networks, relay drivers, and systems operating from multiple supply rails. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors, where its primary role is threshold detection rather than linear amplification. Two independent channels allow one package to implement two unrelated sensing functions while sharing a common supply connection and ground reference. The LM2903 series combines low input-offset voltage, low input-bias current, and a wide supply-voltage range. Input offset voltage is specified as low as 2.0 mV, which helps define the input-voltage difference required to change output state. The 2 V to 36 V operating range supports legacy 5 V logic, industrial 12 V and 24 V rails, automotive-style 12 V systems, and higher-voltage threshold-detection circuits. The open-collector outputs permit an external pull-up voltage to be selected independently of the comparator supply. Each channel compares a non-inverting input with an inverting input. When the non-inverting voltage is higher, the corresponding open-collector output transistor turns on and pulls the output toward the pull-up rail; when the inverting voltage is higher, the transistor turns off and the output rises. The two channels are independent, although their supply and ground pins are shared. This arrangement supports sensor thresholding, window detection, and complementary decisions without requiring two separate packages. Typical uses include industrial control and factory automation, battery-powered monitoring, automotive battery and power-system detection, instrumentation, protection circuits, and embedded systems using 3.3 V or 5 V microcontroller interfaces. For digital interfaces, the open-collector output can use a pull-up to the logic rail used by a comparator input or microcontroller. The SOIC-8 package also supports conventional surface-mount assembly and hand-soldering workflows. Designers should verify the allowable input and output voltage relationships, including the differential input range, and use a pull-up resistor that supplies adequate output current without exceeding the output transistor's limits. Care is also needed when a channel drives a cable, relay, or large capacitance because slower edges and parasitic coupling can affect system behavior. The input network should include suitable filtering when the sensed signal contains switching noise. This product overview combines the exact LM2903DR2 ordering identity with practical guidance on comparator operation, pin usage, output interfacing, and verified drop-in options. It is intended to support component selection, PCB replacement, and design reviews involving dual open-collector comparators in SOIC-8 packages.

RFQ Contact
LM2903DR2G - Dual 36V Open-Collector Comparator | onsemi
LM2903DR2G

LM2903DR2G - Dual 36V Open-Collector Comparator | onsemi

onsemi LM2903DR2G is a dual differential voltage comparator with two independent comparator channels, 2 V to 36 V supply operation, open-collector outputs, 1.5 µs propagation delay, and an 8-pin SOIC package. The device also supports split-supply operation with stated rails from ±1 V to ±18 V and an input offset voltage as low as 2.0 mV. A dual comparator is a semiconductor that evaluates two input voltages and changes its output state according to their relationship. The LM2903 belongs to the broader voltage-comparator hierarchy within analog integrated circuits and power-management signal conditioning. Its two independent channels allow simultaneous or separate threshold, window, sensing, and level-detection functions without requiring two separate comparator packages. Key features include two open-collector channels, a 1.5 µs response time, and low-offset operation with input offset voltage specifications as low as 2.0 mV. The 2 V to 36 V total supply range supports industrial, automotive-style, and embedded applications where the comparator may operate from a single supply or from positive and negative rails. Open-collector outputs permit external pull-up selection and can interface with TTL, MOS, or CMOS-compatible systems when the pull-up voltage and current are appropriate. The comparator architecture is appropriate when a design needs a digital decision rather than a linear analog output. Each channel can compare a sensed voltage against a reference threshold, while the open-collector structure allows wired logic, alarm signaling, or direct control of a pull-up-equipped input. Operation from single or split supplies expands its usefulness in power systems that use both positive and negative reference rails. Typical applications include automotive battery and power-rail monitoring, industrial control thresholds, motor and actuator interfaces, sensor conditioning, overvoltage and undervoltage detection, and embedded system supervision. The 8-SOIC package provides a conventional surface-mount footprint, while the dual-channel configuration helps reduce component count in dual-threshold or multi-channel sensing designs. Designers should verify input common-mode limits, output pull-up values, differential input limits, and the exact electrical grade associated with the selected ordering code. Keep output pull-up paths short, provide adequate return-current routing, and account for the open-collector output’s tendency to sink current rather than source it. The Request a Quote form on this page supports current commercial sourcing questions. This page organizes the LM2903DR2G electrical characteristics, package information, drop-in candidates, comparison parameters, and practical circuit-placement guidance. It also identifies which ordering variants are technically suitable for footprint reuse and where direct replacement requires additional engineering review.

RFQ Contact
LM2903DRE4 - Dual 2-36V Comparator | Texas Instruments
LM2903DRE4

LM2903DRE4 - Dual 2-36V Comparator | Texas Instruments

Texas Instruments LM2903DRE4 is a dual differential voltage comparator with open-collector outputs, rail-to-rail input capability, a 2 V to 36 V supply range, and an 8-pin SOIC package. Each channel can operate independently, making the device suitable for threshold detection, level translation, window monitoring, and industrial control tasks. A voltage comparator is an analog semiconductor that compares two input voltages and changes its output state when one input crosses the other. A dual comparator contains two electrically independent comparator channels in one package. The LM2903 belongs to the voltage comparator hierarchy, where it can be described more specifically as a differential comparator with open-collector outputs. It operates from a single supply or from split supplies, making it suitable for industrial power systems with widely separated ground references. The principal advantages of the LM2903DRE4 are its broad 2 V to 36 V operating supply range, rail-to-rail input characteristic, low typical supply-current drain of 0.4 mA per comparator, and 300 ns response time. The two open-collector outputs allow the output state to be pulled up to an external voltage and provide wired-AND behavior when several comparators share a pull-up resistor. This output arrangement is useful when interfacing with open-drain logic, relay drivers, or subsequent CMOS and TTL stages. Each comparator contains independent input and output circuitry. Differential input voltage is evaluated between the inverting and noninverting inputs, and the output transistor is turned off or on according to that relationship and the polarity of the open-collector stage. Because the outputs are open collector, the output voltage depends on the pull-up network rather than the comparator alone. Designers must account for leakage current, pull-up resistance, logic thresholds, and propagation delay when translating a high-impedance output state into a valid digital level. Typical uses include industrial sensor thresholds, battery and power-supply monitoring, overvoltage detection, motor-control signaling, and general-purpose logic interfacing. A split-supply arrangement can compare bipolar signals around ground, while a single-supply arrangement supports systems whose input common-mode range reaches the lower supply rail. The 8-pin SOIC package also supports conventional surface-mount assembly and easy routing between two comparator channels. A key design consideration is that open-collector outputs require an external pull-up resistor. Select that resistor so that its maximum current and the output leakage current still produce a valid high level, while keeping rise time consistent with the required system response. The 300 ns propagation delay is important for high-speed threshold decisions, but slower pull-up networks can add additional delay after the comparator changes state. This page combines manufacturer and distributor information with package guidance, application analysis, cross-brand substitution notes, and engineering-focused design advice to help evaluate the LM2903DRE4 beyond a basic catalog listing.

RFQ Contact
LM2903DRG3 - Dual Open-Collector Comparator | Texas Instruments
LM2903DRG3

LM2903DRG3 - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903DRG3 is a dual differential comparator with open-collector outputs, operating from 2 V to 36 V on a single supply or ±1 V to ±18 V on dual supplies, in an 8-pin SOIC package. Each of the two independent comparator channels draws 200 µA of supply current and offers a 1 µs response time, making the LM2903DRG3 a standard general-purpose comparator for industrial, automotive and instrumentation signal chains. A comparator is a differential amplifier whose output is driven to a logic state when one input exceeds the other by more than the input offset voltage. It belongs to the amplifier IC family, sits under the operational amplifier hierarchy, and ultimately falls inside the linear and signal-conditioning IC category. Unlike an op-amp, a comparator has no linear output region and is not intended for open-loop gain; its open-collector output is designed to pull a rail low and to be pulled up externally, which allows it to sink more current than a CMOS push-pull output can. Key features include a maximum rated supply of up to 38 V, an ESD rating of 2 kV HBM, a low input offset voltage of 0.37 mV and a low input bias current of 3.5 nA, all of which improve threshold accuracy and reduce source loading on the sensed signal. The differential input voltage range is equal to the maximum rated supply voltage at ±38 V, and the common-mode input voltage range includes ground, allowing the device to monitor bipolar signals referenced to 0 V. Outputs are compatible with TTL, MOS and CMOS logic families. Electrically the device is a bipolar dual differential comparator with an open-collector output stage. The open-collector architecture means the output can be pulled to any supply level the system uses, and a pull-up resistor sets the high level. This is essential in relay-drive, lamp-drive and level-shifting designs where the load requires more current than the IC itself can source. Typical applications include industrial sensor threshold detection, battery and rail window comparison, overvoltage and undervoltage protection in power supplies, temperature monitoring with thermistors or RTDs, and current-sense comparison in motor drive and inverter control stages. When designing with the LM2903DRG3, always place the pull-up resistor close to the output pin and check that the total sink current stays within the output rating, because the open-collector transistor, not the internal drive, sets the load capability. This page consolidates parametric data, drop-in alternatives, comparison tables and practical design notes so engineers can evaluate the LM2903DRG3 against equivalent dual comparators without rebuilding the analysis from scratch.

RFQ Contact
LM2903DRG4 - Dual 30V Open-Collector Comparator | Texas Instruments
LM2903DRG4

LM2903DRG4 - Dual 30V Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903DRG4 is a dual differential voltage comparator with an open-collector output, supplied in an 8-pin SOIC package. It operates from a single supply over a 2 V to 30 V range, or from dual supplies when the total supply difference remains within 2 V to 36 V. The device contains two independent comparators, making it suitable for threshold detection, window comparison, and industrial control functions. The LM2903 is a general-purpose comparator within the broader category of analog comparator ICs. A comparator evaluates two input voltages and produces a logic-level result indicating which input is higher. In an open-collector implementation, the output stage can sink current while remaining in a high-impedance state when the device is inactive. This architecture allows external pull-up resistors to set the output voltage and interface with TTL, MOS, or CMOS logic. Key characteristics include a 2 V to 30 V supply range for the non-V device, a 30 V maximum supply rating, approximately 1.3 microsecond propagation delay, and typical supply-current drain of approximately 0.4 mA per comparator. The input common-mode range includes ground, and the differential input voltage range is equal to the maximum-rated supply voltage at ±38 V for the versions described by the manufacturer. The open-collector outputs require pull-up resistors when connected to digital logic. The outputs are intended to sink rather than source output current, so the pull-up resistor value determines the rise time, power consumption, and compatibility with the receiving logic. The wide supply range and low-power operation make the LM2903 suitable for process control, power supervision, sensor conditioning, and general-purpose threshold detection. When designing around the LM2903, verify the supply limits, common-mode input range, differential input limits, output pull-up network, and the switching behavior required by the downstream circuit. The device is a dual comparator, so each channel is independent, but both channels share the same supply pins and package footprint. The SOIC-8 format supports conventional surface-mount assembly and provides a practical upgrade path from through-hole comparator designs when the pin configuration is verified. This page brings together the manufacturer product information, verified distributor references, package details, drop-in comparison options, and application guidance for engineers evaluating the LM2903DRG4 in new analog-control and embedded-system designs.

RFQ Contact
LM2903EPWRQ1 - Automotive Dual Comparator | Texas Instruments
LM2903EPWRQ1

LM2903EPWRQ1 - Automotive Dual Comparator | Texas Instruments

The Texas Instruments LM2903EPWRQ1 is an automotive dual differential comparator with two independent comparator channels, open-collector outputs, and operation across a 2 V to 30 V supply range. It is qualified to AEC-Q100 Grade 0 and Grade 1 and is packaged in an 8-pin TSSOP (PW) package for automotive and industrial systems. The device is intended for high-voltage signal-chain applications where a robust differential input comparator is needed to monitor two voltages and report their relationship. A comparator is an analog integrated circuit that compares an input voltage with a reference or threshold voltage and switches its output when the differential polarity changes. LM2903EPWRQ1 belongs to the differential comparator family within the broader voltage-comparison, signal-conditioning, and power-management IC hierarchy. Its differential inputs allow one signal to be evaluated against another rather than against a fixed internal reference, making it useful for threshold detection, overvoltage and undervoltage monitoring, sensor conditioning, and control systems. The dual-channel architecture provides two comparators in one package while keeping each channel independent. The open-collector output structure allows the output transistor to remain off when the output is high-impedance, which supports wired logic, pulled-up buses, and systems requiring an external pull-up resistor. The automotive qualification provides an important distinction from standard industrial comparator variants because the LM2903-Q1 family is characterized for Grade 0 and Grade 1 operating environments. Typical applications include automotive battery monitoring, 12 V and 24 V power-system supervision, sensor threshold detection, window and system monitoring, industrial control panels, and automotive actuator or interface circuits. The 30 V maximum supply rating provides useful headroom for systems with battery transients and elevated industrial rails. When designing a comparator circuit, verify the input common-mode range, output pull-up requirements, propagation delay, and the electrical limits for the intended automotive operating environment. The LM2903EPWRQ1 is supplied in an 8-pin TSSOP (PW) package, allowing compact PCB placement while supporting the pin arrangement of the LM2903-Q1 family. For new designs, confirm the selected ordering code against the manufacturer datasheet and validate the external pull-up resistor and input filtering for the specific signal environment.

RFQ Contact
LM2903FVJ-E2 - Dual Ground-Sense Comparator | ROHM Semiconductor
LM2903FVJ-E2

LM2903FVJ-E2 - Dual Ground-Sense Comparator | ROHM Semiconductor

ROHM Semiconductor LM2903FVJ-E2 is a dual-channel, general-purpose ground-sense comparator with open-collector outputs and a 3 V to 32 V operating supply range. The device is packaged in an 8-pin TSSOP-B8J package and is supplied in tape-and-reel packing. ROHM lists the LM2903FVJ as Not Recommended for New Designs, so the part is best evaluated for existing designs, maintenance, and previously qualified industrial equipment rather than new product creation. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level result indicating which input is higher. The dual architecture provides two comparison channels in one package, reducing component count when a board needs independent threshold decisions. The LM2903FVJ-E2 is intended for ground-sense applications, where a comparator evaluates a signal relative to a ground-referenced threshold and drives an open-collector output. Open-collector outputs allow wired-AND behavior when several outputs share a pull-up resistor, which is useful in alarm, interlock, and system-fault signaling circuits. The key operating characteristics are the 3 V to 32 V supply range, two comparator channels, ground-sense input arrangement, and open-collector output architecture. The broad supply range allows the device to operate from conventional 5 V and 12 V industrial rails as well as higher-voltage systems, subject to the limits in the manufacturer datasheet. Its open-collector output stage requires an external pull-up resistor when a logic-high output is required. The output should not be assumed to drive a load directly; the pull-up resistor, downstream logic input, and fault-state behavior must be checked together. Typical uses include overvoltage and undervoltage indication, ground-fault detection, battery or power-supply monitoring, industrial control interlock logic, threshold-based signal conditioning, and general embedded control. The comparator can operate directly from higher-voltage rails, but the input pins, output pull-up network, grounding, and protection network must remain within their specified limits. External filtering or clamping may be required when the monitored signal contains transients or exceeds the input common-mode range. Designers should review the ROHM datasheet for the complete electrical limits, input common-mode range, output sink-current capability, response-time behavior, and package details before release to production. Because the manufacturer marks the LM2903FVJ as Not Recommended for New Designs, a responsible product decision should compare current ROHM alternatives rather than treating this part as the preferred choice for a fresh design. Existing production equipment may still benefit from a qualified replacement strategy when availability, lifecycle status, and electrical compatibility are reviewed. This product summary consolidates the manufacturer product identity, package information, lifecycle status, operating-range information, practical application guidance, and sourcing questions into one engineering reference. It is intended to support initial part identification, circuit review, and replacement planning without replacing the complete manufacturer datasheet.

RFQ Contact
LM2903FVT-E2 Dual Ground-Sense Comparator | ROHM
LM2903FVT-E2

LM2903FVT-E2 Dual Ground-Sense Comparator | ROHM

ROHM Semiconductor LM2903FVT-E2 is a dual-channel ground-sense comparator with open-collector outputs, a 3 V to 32 V operating-voltage range, and low supply current. The device is supplied in an 8-pin TSSOP-B surface-mount package for compact industrial and automotive electronic systems. Its two independent comparator channels compare input signals against ground-sensitive thresholds and drive open-collector outputs suitable for pull-up-based interfacing. A comparator is an analog integrated circuit that evaluates one input voltage relative to another and changes its output state when the relationship between those voltages crosses a defined threshold. The LM2903 series belongs to the broader open-collector comparator hierarchy, which combines analog signal conditioning, threshold detection, and digital-compatible output signaling. Ground-sense operation is particularly useful when the reference or monitored signal is referenced to the system ground rather than to a mid-supply rail. The principal features of the LM2903FVT-E2 include two comparator channels, a wide 3 V to 32 V supply range, low supply current, and open-collector outputs. The open-collector architecture allows the output transition speed to be influenced by an external pull-up resistor and load capacitance. This flexibility makes the device suitable for wired logic, relay or solenoid interfaces, threshold monitoring, and systems where the pull-up voltage must be selected independently from the comparator supply. The wide operating-voltage range allows the comparator to operate from low-voltage 3 V systems through substantially higher supply rails, subject to the absolute maximum ratings and application conditions defined by the manufacturer. Because each channel uses an open-collector transistor, an external pull-up resistor is required to establish a valid high output level. The pull-up voltage, resistor value, allowable sink current, and rise time should be selected together according to the required operating frequency and connected load. Typical applications include automotive and industrial control modules, battery-powered equipment, overvoltage and undervoltage detection, sensor-threshold conditioning, window or level detection, and general digital control systems. The low supply-current characteristic is particularly relevant to systems that maintain operation across a broad supply range without continuously operating from a tightly regulated rail. The TSSOP-B package supports compact layouts, although careful PCB planning remains necessary for clean signal routing. For reliable implementation, connect the required pull-up resistor to the pull-up supply, keep comparator input traces short, and avoid routing high-current or fast-switching paths near the input pins. Confirm the input common-mode limits, differential input limits, output current, and supply decoupling requirements against the manufacturer datasheet for the selected automotive and temperature grades before production release. This product record combines the manufacturer product description with distributor packaging information and practical guidance for comparator implementation, PCB integration, output pull-up design, and drop-in replacement assessment. It also distinguishes verified ordering information from engineering assumptions so engineers can review the circuit and manufacturing implications before selecting a comparator for a new design.

RFQ Contact
LM2903HD - Dual 36V Open-Collector Comparator | STMicroelectronics
LM2903HD

LM2903HD - Dual 36V Open-Collector Comparator | STMicroelectronics

STMicroelectronics LM2903HD is a low-power dual differential voltage comparator designed for single-supply operation from 2 V to 36 V or dual-supply operation from ±1 V to ±18 V. Each channel provides an open-collector output, and the device is supplied in an 8-pin SOIC package with tube packing. The LM2903HD combines two independent comparators in one package for threshold detection, level translation, window sensing, and general-purpose signal conditioning. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its open-collector outputs can sink current from a pull-up network, making the device suitable for wired logic, relay drivers, and interface applications where the output must connect to another supply domain. The STMicroelectronics LM2903 datasheet identifies a wide supply range of 2 V to 36 V under single-supply operation and ±1 V to ±18 V under dual-supply operation. It also specifies low supply-current drain independent of supply voltage and a typical drain of 0.4 mA per comparator. These characteristics allow economical operation from industrial, automotive, and embedded supply rails while preserving useful input and output operating ranges. The differential input arrangement places the inverting and non-inverting terminals on separate comparator channels. When the voltage applied to the non-inverting input exceeds the corresponding inverting input, the associated open-collector output transitions according to the comparator's polarity. External resistors normally define the output high state because an open-collector transistor actively pulls the output low but does not source a sustained output voltage. Typical LM2903HD applications include DC threshold detection, battery-voltage monitoring, sensor signal conditioning, window comparators, and logic-level translation. The dual-channel configuration reduces component count in circuits requiring two independent comparisons. Its open-collector outputs also support wired-AND behavior when multiple comparator outputs share a pull-up resistor. PCB design should keep comparator inputs and feedback components away from switching nodes and high-current return paths. Place input resistors and feedback resistors close to the device, use a solid ground reference, and add supply bypassing where required by the implementation. Validate output pull-up values against sink-current limits, propagation delay, and the required logic rise time. This product page combines manufacturer specifications, ordering information, package details, application guidance, and pin-compatible comparison information. It is designed to help engineers identify the LM2903HD quickly, verify its electrical limits, and select an appropriate second source without changing the PCB footprint.

RFQ Contact
LM2903HYDT - Dual 36V Open-Collector Comparator | STMicroelectronics
LM2903HYDT

LM2903HYDT - Dual 36V Open-Collector Comparator | STMicroelectronics

The STMicroelectronics LM2903HYDT is a low-power dual differential voltage comparator with two independent comparison channels, a supply range of 2 V to 36 V, and open-collector outputs in an 8-pin SOIC package. Each channel supports single-supply or dual-supply operation, while the differential input range extends to the maximum rated supply voltage. The typical supply current is 0.4 mA, and the input bias current is 25 nA. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903HYDT belongs to the comparator hierarchy within analog ICs and interface ICs. Its two channels can be used independently, with one channel referenced to ground for single-supply operation or both channels operating from positive and negative rails in dual-supply systems. The open-collector output allows the output state to be pulled up to a suitable external voltage. Key electrical characteristics include a low typical supply current of 0.4 mA, a typical input bias current of 25 nA, and a typical input offset current of ±5 nA. The input common-mode voltage range includes ground, which supports single-supply sensing near 0 V. The open-collector output has a typical low saturation voltage of 250 mV at an output current of 4 mA, while the differential input voltage range equals the maximum rated supply voltage. The LM2903HYDT combines two differential comparators in one package, reducing board area in designs that require more than one threshold decision. Its low operating current suits battery-operated and low-power monitoring systems. Because the outputs are open collector, applications can select the pull-up voltage independently and can wire multiple open-collector outputs together when wired-AND behavior is required. A pull-up resistor is required for normal high-level output operation. Typical uses include overvoltage and undervoltage monitoring, industrial sensor thresholds, battery-pack protection, motor-control interfaces, window or level detection, and general-purpose digital thresholding. The two independent channels can monitor different supply rails or implement hysteresis around a reference voltage. For sensitive systems, input bias current, offset voltage, common-mode limits, output leakage, and propagation delay should be checked against the sensing network and logic family. PCB implementation should keep the comparator inputs away from switching nodes and high-current paths. Place the input resistors and optional hysteresis network close to the associated pins, provide a solid ground return, and route open-collector pull-ups away from sensitive analog inputs. If the input signals can switch rapidly, minimize parasitic capacitance and verify that the external network does not cause input overvoltage during transients. This page combines the electrical limits, package details, pin assignments, practical application guidance, and confirmed pin-compatible alternatives for the LM2903HYDT. It also identifies the parameters that require verification against the latest STMicroelectronics datasheet before production release or unqualified second-source use.

RFQ Contact
LM2903HYPT - Dual Open-Collector Comparator | STMicroelectronics
LM2903HYPT

LM2903HYPT - Dual Open-Collector Comparator | STMicroelectronics

The STMicroelectronics LM2903HYPT is a low-power dual differential voltage comparator with two open-collector outputs, a 2 V to 36 V single-supply range, and an 8-TSSOP package. Each comparator operates from dual supplies of ±1 V to ±18 V, responds in 1.3 µs typically, and draws 0.4 mA per comparator. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903HYPT belongs to the comparator hierarchy within analog ICs and interface electronics. Its differential inputs suit threshold, window, overvoltage, and sensor-conditioning circuits, while the open-collector outputs allow wired AND operation, level translation, or pull-up-based interfacing. Each channel offers a typical input offset voltage of 1 mV, input offset current of ±5 nA, and input bias current of 25 nA. The input common-mode range includes ground, making the device useful in single-supply systems in which signals approach the lower supply rail. Output saturation voltage is 250 mV typical with 4 mA output current, and the outputs are compatible with DTL, TTL, CMOS, ECL, and MOS logic families. The two independent comparators operate over a −40 °C to +150 °C temperature range. The HYPT ordering code places the device in an 8-TSSOP package supplied in tape-and-reel format. Its automotive qualification and RoHS-compliant construction support demanding industrial, automotive, and sensing applications where low input bias, wide supply range, and open-collector interface flexibility are important. Typical uses include battery-powered monitoring, industrial sensor interfaces, overvoltage protection, control-loop threshold detection, and open-drain alarm signaling. The 36 V maximum single-supply operation also permits direct monitoring of higher-voltage systems when the input and supply ratings are respected. For reliable implementation, place input and output traces away from fast-switching nodes, provide a pull-up resistor on each open-collector output, and verify common-mode, differential-input, and output-current limits against the manufacturer datasheet. The low input bias current helps preserve sensor accuracy, while the open-collector output requires an external pull-up. This page combines exact operating specifications, pin-level implementation guidance, application analysis, and package-compatible replacement information to support faster design-in and sourcing decisions.

RFQ Contact
LM2903IMX - Dual 36V Comparator | onsemi | Industrial
LM2903IMX

LM2903IMX - Dual 36V Comparator | onsemi | Industrial

The onsemi LM2903IMX is a dual differential comparator with two independent comparison channels, a 2 V to 36 V single-supply operating range, and an 8-SOIC package. It also supports split supplies up to ±18 V and provides a response time of approximately 1.5 µs. Each channel features open-collector output, allowing the device to pull the output low while external pull-up resistors establish the high logic level. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input rises above the inverting input, or vice versa. The LM2903 belongs to the comparator hierarchy within analog ICs and interface ICs. Unlike an operational amplifier, its primary function is threshold switching rather than linear amplification. This distinction makes the LM2903IMX suitable for sensing, protection, control, and digital-interface applications. The LM2903IMX operates from a single supply as high as 36 V, which supports industrial control systems operating from 24 V rails. Its common-mode input range includes ground, allowing signals close to 0 V to be compared in single-supply systems. Typical supply current is approximately 800 µA, while the 1.5 µs response time supports detection functions that require faster switching than a general-purpose slow comparator. Both comparison channels operate independently, reducing the component count in designs that require two threshold decisions. The open-collector outputs require pull-up resistors to define the inactive output voltage, but this architecture provides useful system-level flexibility: pull-ups can be connected to a local supply, interface voltage, or pull-up network. Input, output, and supply functions are arranged in a standard 8-SOIC footprint suitable for leaded through-hole assembly. Typical uses include 24 V industrial sensor interfaces, battery-powered monitoring circuits, overvoltage and undervoltage detection, window-comparator functions, and logic-level translation between open-collector devices. The broad supply range is particularly useful when a comparator must operate directly from an unregulated industrial rail while its output drives a pull-up connected to a lower-voltage logic domain. Designers should verify the logic thresholds, output sink current, input bias current, and pull-up voltage against the system requirements. Place the pull-up resistor close to the open-collector output, maintain a common ground return between the comparator and sensed circuitry, and avoid exceeding the 36 V maximum supply voltage. The 8-SOIC package is not the smallest option, but it supports straightforward prototyping and hand assembly. This page combines the LM2903IMX operating limits, pin assignments, drop-in replacement options, application guidance, and design considerations to provide practical information for PCB planning, circuit design, and component selection.

RFQ Contact
LM2903ITL/NOPB - Dual Open-Collector Comparator | Texas Instruments
LM2903ITL/NOPB

LM2903ITL/NOPB - Dual Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903ITL/NOPB is a dual differential comparator with two independent comparison channels, open-collector outputs, rail-to-rail input capability, and an 8-pin DSBGA (YZR) package. The specified offset voltage is as low as 2.0 mV maximum, while the listed response time is 1500 ns. Its rated operating-temperature range is -40°C to +85°C. A dual differential comparator is a semiconductor that evaluates the relative voltages applied to its inverting and non-inverting inputs and changes its output state when the difference crosses a defined threshold. The LM2903 family contains two independent comparison channels in one package, allowing one device to monitor two signals. As an analog comparator, it belongs to the comparator hierarchy within interface and signal-conditioning semiconductors, where it converts an analog voltage relationship into a digital logic indication. The open-collector output architecture permits the output stage to remain unpowered when a compatible pull-up network provides the desired logic voltage. This characteristic supports wired connections, interface standards, and system-level voltage-level compatibility. Rail-to-rail input behavior allows the comparison inputs to operate across the device supply range, which is useful when sensing signals near either supply rail. The LM2903-N family is designed for single-supply operation over a wide operating-voltage range. TI identifies the device as a low-offset, dual differential comparator and specifies an offset voltage as low as 2.0 mV maximum for two comparators. The LM2903ITL/NOPB ordering option uses the compact 8-pin DSBGA (YZR) package, making it appropriate for space-constrained assemblies that can accommodate the package dimensions, ball pattern, and assembly process. Typical uses include threshold detection, line-sensing, control-loop signaling, overvoltage and undervoltage indication, signal conditioning, and general dual-channel logic interfacing. In these applications, the comparator can translate a small analog difference into a stable logic-level event. The -40°C to +85°C temperature specification supports industrial and commercial equipment, although the final design must remain within all electrical limits and assembly constraints. Design with the input common-mode range, supply voltage, output pull-up arrangement, input offset, response time, and logic thresholds as a complete system. Confirm the YZR package pin assignment and ball dimensions against the manufacturer datasheet before routing the PCB or beginning assembly. Choose pull-up voltage and resistor values from the connected logic interface rather than assuming the open-collector output supplies a fixed high level. This product summary combines the exact ordering information, package description, operating-temperature range, comparator architecture, offset information, and response-time data needed to evaluate the LM2903ITL/NOPB. It also provides application guidance, practical interface considerations, and sourcing directions for comparing an existing design with other LM2903 ordering options.

RFQ Contact
LM2903ITLX/NOPB - Dual Low-Power Open-Collector Comparator, 8-DSBGA
LM2903ITLX/NOPB

LM2903ITLX/NOPB - Dual Low-Power Open-Collector Comparator, 8-DSBGA

The Texas Instruments LM2903ITLX/NOPB is a dual, low-offset, open-collector differential comparator in an 8-ball DSBGA package, with two independent comparator channels operating from a single supply between 2 V and 36 V. Each channel offers an input offset voltage as low as 2.0 mV maximum for the LM193-series family, an input bias current of 0.25 uA maximum at 5 V, a typical output sink current of 16 mA at 5 V, and a propagation delay of 700 ns maximum. A comparator is a differential input amplifier whose output switches state when one input exceeds the other by more than the offset voltage. Comparators sit at the bottom of the analog signal chain as the decision element that converts a small analog difference into a logic-level event. The LM2903 belongs to the LM193/LM2903/LM393 family, a classic general-purpose voltage comparator family, and this device adds a low-power, wide-supply differential pair plus a saturating open-collector transistor output stage. Key features of the LM2903ITLX/NOPB include open-collector outputs that can be pulled up to any logic level up to the supply rail, differential input range of plus or minus 18 V, common-mode input voltage range that includes ground, an industrial temperature grade of -40 C to +85 C, and total quiescent current of 2.5 mA maximum for the pair. The open-collector architecture allows multiple comparators to be wire-ORed on a shared pull-up resistor, which is the standard technique for driving slow, high-voltage relay, lamp, or open-drain bus loads. Internally the device is a bipolar dual-diff-pair design with an emitter-stabilized differential input stage feeding a saturated open-collector output transistor. Because the output stage is open collector rather than push-pull, output rise and fall times are set by the pull-up resistor and the load capacitance rather than by an internal driver, which allows a designer to trade speed for EMI margin. The wide 2 V to 36 V supply span lets a single part sense signals referenced to either a low-voltage logic rail or a 24 V industrial bus. Typical applications include over/under-voltage and window monitoring in power supplies, sensor threshold conditioning for industrial and automotive sensing chains, zero-cross and level detection in motor control and drive electronics, open-drain bus arbitration in multi-drop industrial networks, and general-purpose analog signal conditioning where an open-collector output must drive a relay or an opto-isolator. Design consideration: because the outputs are open collector, an external pull-up resistor is mandatory, and its value sets the output rise time. Keep pull-ups high enough to limit sink current within the 16 mA typical output rating, and low enough to achieve the required switching speed with the total bus capacitance. This page consolidates parametric detail, drop-in alternatives for the same 8-DSBGA footprint, and practical layout and pull-up guidance that is not assembled in one place in the original LM2903 documentation.

RFQ Contact
LM2903M - Dual Differential Comparator | Texas Instruments
LM2903M

LM2903M - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM2903M is a dual differential comparator in an 8-pin SOIC package. It contains two independent comparator channels, operates from a single supply or split supplies, and provides open-collector output stages suitable for driving external pull-up networks. The verified distributor listing identifies the device as a standard general-purpose comparator with rail-to-rail input capability, while the linked Fairchild datasheet describes the LM2903 family as a dual differential comparator designed for operation from a 2 V to 36 V supply. The LM2903M combines two precision comparators with low input offset voltage, low supply current, and a propagation delay listed by a verified distributor source as 1.5 microseconds. A comparator is a differential amplifier with a logic output rather than a conventional analog output. It evaluates the voltage relationship between its inverting and non-inverting inputs and produces a saturated digital state when the selected input exceeds the reference. In the LM2903M, two independent channels allow one device to perform two threshold decisions, window comparisons, or complementary sensing functions. This makes the part useful as a building block within logic ICs, interface ICs, industrial control systems, and discrete analog signal-conditioning circuits. Key features include dual differential comparison, an open-collector output, single-supply operation from 2 V to 36 V, support for split-supply operation, and an 8-SOIC surface-mount package. The open-collector outputs can be wired to a common pull-up rail when multiple comparators need a shared bus, although the pull-up resistor and external logic voltage must be selected for the intended interface. The reported 1.5 microsecond response time is adequate for many industrial and control applications where the system does not require sub-microsecond decisions. The LM2903 family is designed for low-power operation independent of the supply voltage, which helps conserve energy in battery-powered and distributed equipment. Each channel has independent input and output behavior, allowing one channel to monitor a sensor while the second channel provides an alarm, window-limit, or control function. Input and output behavior should still be checked against the complete manufacturer datasheet for the exact ordering code before production use. Typical applications include battery monitoring, industrial sensor interfaces, overvoltage and undervoltage detection, temperature threshold circuits, power-supply sequencing, and general-purpose logic control. The open-collector output is especially useful when driving a relay, opto-isolator, or another device that requires a pulled-up supply domain. The SOIC-8 footprint is suitable for conventional surface-mount PCB assembly, but the exposed package dimensions and lead geometry should be checked against the mechanical drawing. For a reliable design, begin by verifying the input common-mode range, output sink current, supply-current limits, and propagation delay against the required operating conditions. Do not leave the open-collector outputs without an appropriate pull-up resistor unless the intended load provides one. Decoupling capacitors should be placed close to the supply and ground pins, and input traces should be kept short to reduce noise pickup. This product page combines verified manufacturer and distributor information with engineering guidance, comparison data, and practical design notes to support component selection and PCB implementation.

RFQ Contact
LM2903M/NOPB - Dual Open-Collector Comparator | Texas Instruments
LM2903M/NOPB

LM2903M/NOPB - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903M/NOPB is a dual differential analog comparator with two independent channels, low offset voltage, and open-collector outputs in an 8-pin SOIC package. According to the manufacturer product information, the device supports a single-supply operating range extending to 18 V and an operating temperature range of -40°C to 85°C. Its maximum input offset voltage is specified as low as 2 mV, while input current values of 2 nA and 5 nA appear in the product listing. An analog comparator is a signal-conditioning semiconductor that compares two input voltages and changes its output state when one input exceeds the other. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. A differential comparator can operate from a single supply or split supply, allowing it to compare signals near ground, bipolar signals, or thresholds referenced to a supply rail. The LM2903M/NOPB provides two independent low-power, low-offset comparators in one package. Its open-collector outputs are designed for wired-interface use and require an external pull-up resistor to establish a positive logic high when the output transistor is off. The listed propagation delay is 1.5 microseconds, making the device suitable for threshold detection, level translation, relay or solenoid driving, and general industrial control functions where microsecond-scale decision speed is sufficient. A broad supply range is useful in equipment operating from industrial or automotive-style voltage rails. The -40°C to 85°C temperature range supports industrial and extended-temperature environments, although the specific LM2903M/NOPB orderable status and quality qualification should be checked for each deployment. The 8-pin SOIC package is a standard surface-mount footprint that is larger than contemporary compact packages but remains convenient for hand assembly, prototyping, and through-hole-style external pull-up routing. Typical uses include monitoring a sensor against an adjustable threshold, detecting overvoltage or undervoltage conditions, converting an analog level into a logic event, and providing two independent comparisons in control, instrumentation, or power-supply systems. Because the outputs are open collector, multiple devices or nodes can share a pull-up arrangement when the electrical conditions permit. Designers should account for input common-mode range, output pull-up requirements, supply decoupling, and the effect of input bias current when selecting threshold resistors. Keep comparator inputs away from switching-node currents and provide a stable local ground reference. The open-collector nodes should have pull-up resistors selected for the required logic voltage, sink-current budget, rise-time target, and system power budget. This page combines the manufacturer's ordering information, a source-grounded parameter summary, application engineering guidance, and package-level replacement analysis. It also identifies the design trade-offs that matter when comparing the LM2903M/NOPB with related dual comparators rather than relying only on basic device descriptions.

RFQ Contact
LM2903M/SL160222 - Dual Differential Comparator | Texas Instruments
LM2903M/SL160222

LM2903M/SL160222 - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM2903M/SL160222 is a dual differential comparator containing two independent precision voltage comparators in an 8-pin SOIC package. It supports single-supply operation, provides an input offset voltage specification as low as 2.0 mV maximum for two comparators, and uses open-collector outputs. The device is intended for general-purpose signal comparison, threshold detection, industrial control, and interface applications. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The comparator category sits within analog signal-processing ICs, alongside amplifiers and voltage references, while remaining distinct from a general-purpose operational amplifier. The LM2903 architecture combines two independent channels in one package, reducing board area when two comparison functions are required. The LM2903 family is designed to operate from a single power supply over a wide voltage range. According to the manufacturer datasheet, the offset voltage can be specified as low as 2.0 mV maximum for the two-comparator configuration. Open-collector outputs permit wired connections to pull-up circuitry and provide a flexible interface to TTL, MOS, and CMOS-compatible systems. Each channel offers separate inverting, non-inverting, and output terminals. Because the two sections are electrically independent, engineers can use one channel for a sensor threshold and the second for a system interlock or control signal. The single-supply architecture is useful in equipment where one supply rail defines the comparator signal domain. Input and output operating conditions, channel-to-channel behavior, supply-current characteristics, and absolute maximum ratings should be checked against the exact manufacturer ordering information before production release. Typical applications include industrial sensor interfaces, battery-powered monitoring circuits, overvoltage and undervoltage detection, motor-control logic, window comparators, and digital threshold conditioning. In each case, open-collector outputs can drive a pull-up and logic gate, or serve as an active-low alert signal. The small SOIC footprint also supports compact control boards where two independent channels are valuable. For robust layouts, route comparator inputs away from switching nodes and power inductors, place input-referred bypassing close to the supply pin, and pull each open-collector output up to the appropriate logic supply. Check that the pull-up voltage, input common-mode range, supply voltage, and output sink-current requirement satisfy the application before substituting this part into an existing design. This page consolidates the exact LM2903M/SL160222 ordering information, verified manufacturer and distributor references, pin assignments, drop-in alternatives, and practical application guidance to accelerate schematic review, PCB reuse, sourcing, and replacement planning.

RFQ Contact
LM2903M8-13 - Dual 36V Comparator | Diodes Incorporated
LM2903M8-13

LM2903M8-13 - Dual 36V Comparator | Diodes Incorporated

The Diodes Incorporated LM2903M8-13 is a dual differential analog comparator with two independent comparison channels, a 36 V maximum supply rating, and an 8-pin MSOP package. The device supports single-supply and split-supply operation and is designed for general-purpose signal comparison with open-collector outputs compatible with TTL, CMOS, and MOS logic. An analog comparator is an integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM2903 belongs to the differential-comparator hierarchy, which includes precision comparators, voltage comparators, and general-purpose analog interface ICs. Unlike an operational amplifier, a comparator is optimized for fast decision-making, open-drain or open-collector output signaling, and straightforward connection to digital logic rather than linear analog amplification. The LM2903M8-13 provides two independent comparator channels, a wide 36 V operating range, and a specified 300 ns propagation-delay class. Its low input offset voltage supports decisions when the compared signals differ only slightly. The open-collector architecture permits wired logic, pull-up resistor selection, level translation, and compatibility with multiple logic families. Operation from a single positive supply or from positive and negative split supplies makes the device suitable for both conventional and bipolar signal environments. The LM2903 series uses an open-collector output stage rather than a totem-pole output. Each output therefore requires an external pull-up resistor when used as a normal logic driver. This architecture can provide wired-AND behavior, but it can also expose unused outputs to leakage current and requires careful pull-up selection. The two channels are electrically independent, allowing one device to serve two unrelated threshold, window, sorting, or fault-detection functions. Typical uses include sensor threshold detection, battery and power-supply monitoring, window comparators, overvoltage and undervoltage protection, signal conditioning, relay or reset-control logic, and general interface between analog sensors and digital systems. In dual-rail systems, the split-supply capability supports comparison of bipolar signals. In single-supply systems, the comparator can compare a sensor output against a reference voltage while driving a pull-up-based digital output. Designers should verify input common-mode limits, output current, response time, and pull-up requirements against the intended supply conditions. Keep the comparator input and output paths away from high-current switching nodes, use short traces over a continuous ground plane, and place the pull-up resistor close to the output. Because the open-collector output cannot source current, the chosen resistor must satisfy both the required sink current and the logic-family input-current limits. This product page combines the exact LM2903M8-13 package and rating information with application guidance, engineering design notes, and verified cross-reference results. It also distinguishes confirmed same-package drop-in options from comparator parts that require a different footprint, helping PCB designers avoid substitutions that cannot be installed without redesign.

RFQ Contact