Products (44,000+)

LM2903MX - Dual Differential Comparator | Texas Instruments
LM2903MX

LM2903MX - Dual Differential Comparator | Texas Instruments

Texas Instruments LM2903MX is a dual differential analog comparator containing two independent general-purpose comparator channels in an 8-pin SOIC package. Each channel supports single-supply operation from 2 V to 36 V or dual-supply operation from 1 V to 18 V, and the device includes rail-to-rail input capability, an open-collector output, and a typical response time of 1.3 us. The open-collector outputs are compatible with CMOS, MOS, and TTL logic. An analog comparator is an integrated circuit that evaluates two input voltages and changes its output state according to their relative polarity. Within the semiconductor hierarchy, a comparator belongs to the broader group of analog ICs and serves as an interface between sensors and digital logic. The LM2903MX is useful when a design needs to detect crossings, thresholds, overvoltage, undervoltage, or differences between two analog signals without converting them into a digital quantity. The two channels operate independently, allowing one device to implement two unrelated threshold functions. Key features include comparison of input voltages near ground potential, a wide supply range, low current drain, and open-collector outputs that require an external pull-up resistor. Rail-to-rail input behavior is particularly valuable when the signal of interest lies close to either supply rail. The specified 1.3 us response time makes the comparators appropriate for power-line, protection, sensing, and general signal-conditioning circuits. Typical uses include monitoring a divided battery voltage, detecting an over-temperature condition with a sensor, comparing an adjustable reference with an analog input, and translating a sensor threshold into a logic-level event. The open-collector topology also allows several comparator outputs to share a wired bus when each output has a suitable pull-up and the system design accounts for the resulting behavior. PCB implementation should follow the manufacturer pin-description table and place input, output, and decoupling connections to minimize switching noise. Input traces should be kept short and away from high-current paths. Use a pull-up resistor sized for the target logic family, and verify its maximum current across all operating conditions. Do not substitute a push-pull output device without reviewing the full pinout and signal behavior. This page compares the LM2903MX with documented same-footprint alternatives, summarizes verified electrical and package characteristics, and adds practical PCB, logic-interface, and replacement guidance for engineers evaluating this dual comparator.

RFQ Contact
LM2903MX-ON - Dual Open-Collector Comparator | onsemi
LM2903MX-ON

LM2903MX-ON - Dual Open-Collector Comparator | onsemi

The onsemi LM2903MX-ON is a dual open-collector voltage comparator for single-supply or split-supply operation, housed in an 8-pin SOIC package. It provides two independent comparator channels, a common-mode input range extending to ground during single-supply operation, and input offset voltage as low as 2.0 mV. The device supports supply voltages from 2 V to 36 V and is specified for an operating temperature range of -40°C to +85°C. A voltage comparator is an analog integrated circuit that compares two input voltages and switches its output when the difference crosses a specified threshold. The LM2903 family belongs to the comparator hierarchy, which sits within analog and mixed-signal semiconductors used for threshold detection, sensing, and control. Its two channels can operate independently from a shared supply, allowing one device to implement two comparison functions in a compact footprint. The primary features of the LM2903MX-ON are its dual-channel architecture, open-collector outputs, wide operating supply range, and low-offset capability. Open-collector outputs permit an external pull-up resistor to establish the output logic level. This arrangement supports wired-AND behavior and allows interface levels to be selected by changing the pull-up supply rather than relying on a dedicated output-supply pin. Each internal comparator has two inputs and one output. With single-supply operation, the common-mode input range can include ground, making the device useful for monitoring signals near 0 V. Split-supply operation permits comparison around a midpoint reference. Because the two channels are independent, they can compare separate sensor or threshold pairs while sharing the same package and supply architecture. Typical applications include industrial sensor interfaces, battery and power-system monitoring, control-loop threshold detection, window comparison, and general-purpose digital conditioning. The dual channel reduces board area when two independently referenced signals must be evaluated. The open-collector architecture is especially useful where the output must drive a pull-up rail, connect to a wired logic bus, or interface with a microcontroller input. PCB design should reserve a pull-up resistor for each open-collector output and route the input and output paths away from high-current switching nodes. The wide 2 V to 36 V supply range supports both low-voltage systems and higher industrial rails, but input and output operating conditions must remain within their respective absolute maximum ratings. This product page combines the LM2903MX-ON technical characteristics, verified manufacturer information, pin-level guidance, drop-in alternatives, and practical design considerations. These engineering details help shorten component selection and support direct PCB, sourcing, and lifecycle planning for dual-comparator designs.

RFQ Contact
LM2903MX-TI Dual Comparator | Texas Instruments
LM2903MX-TI

LM2903MX-TI Dual Comparator | Texas Instruments

The Texas Instruments LM2903MX-TI is a dual differential comparator with open-collector outputs, rail-to-rail input capability, and support for single-supply or dual-supply operation. The device operates with supply voltages up to ±18 V, equivalent to a 36 V total span, and is offered in an 8-pin SOIC package. Its two independent channels make it suitable for threshold detection, window comparison, and signal conditioning systems. A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital logic result indicating which input is higher. Within the semiconductor hierarchy, the LM2903MX-TI belongs to the comparator family, which is part of broader interface and signal-conditioning ICs. Its differential inputs reduce sensitivity to common-mode voltage, while the open-collector outputs allow the output state to be pulled up to a suitable external supply voltage. The LM2903 family combines two comparison channels in one package. Rail-to-rail input operation supports sensing near the supply rails, and the open-collector architecture provides flexible interface levels when paired with an external pull-up resistor. The 8-pin SOIC package supports conventional surface-mount assembly and is also available in tape-and-reel ordering. Exact offset, response-time, current, and temperature limits should be confirmed from the manufacturer datasheet before final circuit release. The dual-channel organization reduces component count in systems requiring two independent decisions. Separate open-collector outputs can drive digital logic, relay drivers, optocouplers, or other devices that require a pulled-up bus. Because an open-collector transistor can hold the output low but cannot actively drive it high, the pull-up voltage and resistor must be selected to match the driven interface and required rise time. Typical applications include industrial sensor thresholding, battery and power-system monitoring, overvoltage and undervoltage detection, waveform crossing detection, and general-purpose control logic. Two channels can implement complementary comparisons or a hysteretic switching arrangement. The device is also appropriate for educational and prototyping systems where a conventional dual comparator in an 8-pin SOIC is required. Designers should verify the input common-mode range, supply limits, output sink-current capability, input offset voltage, and response time against the manufacturer datasheet. Keep input and output return paths short, place pull-up resistors close to the relevant output pins, and account for input filtering when the compared signals contain noise or switching transients. This product page organizes the LM2903MX-TI package, sourcing, pinout availability, and design considerations while identifying same-package alternatives for engineering evaluation. Confirm electrical equivalence, lifecycle status, and manufacturing qualifications before approving a substitution.

RFQ Contact
LM2903MX/NOPB - Dual Open-Collector Comparator | Texas Instruments
LM2903MX/NOPB

LM2903MX/NOPB - Dual Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903MX/NOPB is a dual differential analog comparator with two independent comparator channels, low offset voltage, open-collector outputs, and rail-to-rail input capability in an 8-pin SOIC package. The device is intended for low-power applications operating from a single supply or split supplies, with a manufacturer-specified operating temperature range of -40°C to 85°C for this ordering variant. An analog comparator is a semiconductor that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the broader voltage comparator hierarchy, where each channel can evaluate a non-inverting input against an inverting input. Its open-collector outputs can sink output-stage current while leaving the output otherwise undriven in the high state, allowing a pull-up resistor to establish the logic-high voltage and support wired logic or level translation. The LM2903 provides two independent comparators in one package. Its differential input arrangement is useful when a circuit must detect whether a measured voltage is above or below a reference threshold. The low-offset characteristic reduces the input-voltage difference required to change output state, which is valuable in sensing circuits where small signal changes must be resolved accurately. Open-collector outputs also provide flexibility when driving pull-up resistors to a supply selected by the system designer. The rail-to-rail input characteristic expands the usable common-mode range of the comparator, while the low-power architecture suits battery-powered and general-purpose industrial designs. Because the two channels are independent, one package can implement two threshold detections, window-limit functions, or separate monitoring functions. Common implementations include overvoltage detection, undervoltage indication, temperature or sensor threshold switching, and simple control-loop decisions around a regulated supply. Typical applications include industrial control boards, battery-powered instrumentation, sensor interfaces, power-supply supervision, and embedded systems requiring logic-compatible threshold decisions. The 8-pin SOIC package supports conventional surface-mount assembly and works well where moderate pin count and straightforward layout are priorities. It is also a familiar functional family for designs built around the LM2903, LM2903-N, and related dual-comparator platforms. When designing the circuit, choose the external pull-up resistor to establish a valid logic-high voltage and check that the intended sink current remains within the output-device limits. Keep comparator inputs away from switching-node edges where practical, and evaluate input bias-current effects when the source impedance is high. The open-collector architecture avoids an active push-pull output but requires correct pull-up selection for dependable logic levels. This product data combines the exact ordering information for LM2903MX/NOPB with practical guidance on pin use, logic interfacing, common-mode behavior, and drop-in alternatives. It also organizes the comparator’s electrical, environmental, package, and sourcing attributes for faster engineering selection and PCB planning.

RFQ Contact
LM2903N - Dual Voltage Comparator, Open-Collector, 8-DIP | TI/STMicro/onsemi
LM2903N

LM2903N - Dual Voltage Comparator, Open-Collector, 8-DIP | TI/STMicro/onsemi

The LM2903N is a dual-channel low-offset voltage comparator supplied in an industry-standard 8-pin PDIP (DIP-8) through-hole package. It integrates two independent precision comparators with 2.0 mV typical input offset voltage, an open-collector output stage capable of swinging to the negative rail (ground-sense at single supply), and operates from a 2 V to 36 V single supply or ±1 V to ±18 V dual supply rail. The output transistor sinks up to 16 mA typical (6 mA minimum over temperature), making the part suitable for directly driving low-power relays, LEDs, and logic interfaces. A voltage comparator is an analog building block that compares two input voltages and produces a binary digital output; when the non-inverting input exceeds the inverting input, the output switches state. The LM2903N belongs to the LM393/LM2903 family - a long-standing industry standard introduced for low-power single-supply sensing, and it sits in the hierarchy: comparator -> analog comparator -> signal conditioning IC -> integrated circuit. Its open-collector architecture requires an external pull-up resistor (typically 10 kohm to VCC), which lets multiple comparators be wire-ORed together and lets the output pull to a different rail than the supply voltage. Key specifications include a 1.3 us typical response time at 5 V/2 mA, a 2.5 mV maximum input offset voltage (LM2903 grade), an input bias current of 25 nA typical, and ESD clamps on the inputs that tolerate human-body-model discharge. The device operates across the automotive-industrial -40 C to +125 C range (LM2903N suffix N designates the PDIP-8 package, not the temp grade). The LM2903's architecture uses a PNP input stage that gives the inputs an exceptionally wide common-mode range that includes the negative rail (ground), which is why single-supply ground-referenced sensing is its dominant application. The open-collector NPN output stage isolates the comparator logic from the load voltage; only the pull-up rail sets the high-level output. Typical applications include battery monitoring in 12 V/24 V automotive and industrial systems (window detectors, under-voltage cutoff), zero-crossing detectors for mains interfaces when paired with an optocoupler, line-receiver / level-shift interfaces between high-voltage analog and low-voltage logic, threshold alarms and signal-conditioning front-ends, and oscillator / relaxation-oscillator circuits. When designing with the LM2903N, observe one trade-off: open-collector outputs use a pull-up resistor that adds RC delay to the rising edge - at 10 kohm with 100 pF of trace capacitance, rise time is about 1 us. For high-speed logic interfaces downstream, size the pull-up conservatively or use a discrete or integrated push-pull comparator when sub-microsecond edge rates are needed.

RFQ Contact
LM2903N-NS - Dual Precision Comparator | onsemi
LM2903N-NS

LM2903N-NS - Dual Precision Comparator | onsemi

The onsemi LM2903N-NS is a dual, independent precision voltage comparator with open-collector outputs, supplied in an 8-pin PDIP package. It contains two separate comparator channels, an input offset voltage specified as low as 2.0 mV maximum for the LM193/LM2903 family, and operation from either a single supply or split supplies. Its single-supply common-mode capability extends down to ground, making it useful for systems that monitor signals referenced to the supply rail. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 family belongs to the broader comparator category within analog and mixed-signal semiconductors. Unlike an operational amplifier used primarily for linear amplification, each LM2903N-NS channel provides a binary decision function. The open-collector outputs permit wired logic, pull-up arrangements, level translation, and connection to external pull-up networks. The two internal channels are independent, allowing them to perform separate threshold, window, or protection functions without sharing signal paths. Low input offset is important when the two compared voltages are close, because excessive offset can shift the switching threshold and create errors in precision monitoring. The family was specifically designed for single-supply operation over a wide voltage range, while split-supply operation is also supported. Its supply-current drain is independent of the magnitude of the applied supply voltage. The LM2903N-NS combines two independent precision comparators in one through-hole package. Open-collector outputs require suitable pull-up resistors or suitable pull-up logic to establish a valid high output state. Because the output stage is open collector, multiple comparator outputs can be combined when the application supports wired-AND behavior and the electrical conditions remain within the device ratings. Common-mode input limits, supply voltage limits, output sink-current limits, and input-current limits must still be respected. Typical uses include industrial sensor interfaces, battery and power-system monitoring, control systems, threshold detection, overvoltage and undervoltage protection, and general digital logic interfacing. The dual-channel organization is especially useful when two independent thresholds must be monitored in the same circuit. A single package also reduces board area compared with two separate single comparators while retaining straightforward through-hole assembly. For reliable operation, connect unused comparator inputs to a defined potential so they do not float near the switching threshold. Place the input and output pull-up network close to the relevant pins, and check that the external pull-up voltage does not exceed the allowed output and supply limits. The comparator normally responds to an input crossing, so hysteresis or positive feedback may be needed to prevent repeated output transitions when the compared signals are nearly equal. This product page combines the family-level electrical description, package and pin information, sourcing guidance, compatible alternatives, and practical design notes. It also distinguishes true same-footprint replacements from alternatives that require PCB changes, helping engineers assess upgrade options before committing a design to production.

RFQ Contact
LM2903N/NOPB - 36V Dual Open-Collector Comparator | TI
LM2903N/NOPB

LM2903N/NOPB - 36V Dual Open-Collector Comparator | TI

Texas Instruments LM2903N/NOPB is a dual differential comparator with two independent channels, open-collector open-drain outputs, a 36 V maximum supply rating, and an 8-pin PDIP package. The device provides a 2 mV maximum input offset-voltage specification, 1.3 microseconds propagation delay, and an operating temperature range of -40°C to 85°C. A comparator is a signal-conditioning semiconductor that evaluates two input voltages and produces a logic-level result indicating which input is higher. A dual differential comparator combines two independent comparison channels in one package. The LM2903 belongs to the broader comparator and amplifier IC hierarchy and is designed for single-supply operation, split-supply operation, and interfaces where an open-collector output can directly drive pull-up resistors. The principal features include low offset voltage, low power consumption, and open-collector outputs. Open-collector outputs can sink current while remaining in a high-impedance state when inactive, allowing the output transition speed and logic level to be set by an external pull-up network. The two channels operate independently, supporting simultaneous comparison, level detection, window monitoring, or dual-threshold functions in one circuit. The Texas Instruments LM2903-N family is specified for operation from a single supply across a wide voltage range, with an operating range extending to 36 V. The 2 mV maximum offset specification is useful when the comparator must resolve small voltage differences. Its 1.3 microsecond response is suitable for general-purpose industrial control, monitoring, and interface circuits rather than ultra-high-speed signal comparison. Typical applications include industrial sensor interfaces, overvoltage and undervoltage detection, battery threshold monitoring, temperature-control loops, and general digital logic interfaces. The open-drain architecture also allows wired logic, alarm aggregation, and level-shifting arrangements when suitable pull-up resistors are provided. For reliable PCB implementation, place the input and output components close to the device and provide a defined pull-up resistor on each open-collector output. Check the output sink-current limit, input common-mode range, supply decoupling, and unused-channel configuration against the manufacturer datasheet before finalizing the design. This product page combines the exact orderable part information, package information, comparator characteristics, drop-in candidate analysis, and application-focused engineering guidance to support faster component selection and board-level implementation.

RFQ Contact
LM2903NG - Dual Low-Offset Voltage Comparator | onsemi | PDIP-8
LM2903NG

LM2903NG - Dual Low-Offset Voltage Comparator | onsemi | PDIP-8

The onsemi LM2903NG is a dual independent precision voltage comparator with low input offset voltage, open-collector outputs, and single or split supply operation from 2V to 36V, housed in an 8-pin PDIP through-hole package. The device operates over -40C to +105C and supports input common-mode voltage ranges down to ground. A voltage comparator is an analog circuit element that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier IC and signal-conditioning hierarchy of power management and analog semiconductor systems. Unlike an operational amplifier, a comparator is intentionally optimized for fast, saturated switching between two output states rather than linear amplification, and the LM2903 family adds an open-collector output stage that lets multiple devices share a common pull-up node for wired-OR logic. Key features include a supply range of 2V to 36V (single supply) or +/-1V to +/-18V (split supply), input common-mode range that extends to the negative rail, and very low input bias current of about 250nA. The typical response time is approximately 1.5 microseconds, which suits general-purpose threshold detection, level shifting, and oscillator timing rather than high-speed clocking. The LM2903 architecture uses two fully independent comparator channels sharing one die and supply pins. Each channel has its own inverting and non-inverting inputs plus an open-collector output, so external pull-up resistors define the output high level, allowing interface to logic families at any voltage up to the supply rails. Typical applications include power-supply undervoltage and overvoltage supervision, battery threshold monitoring, window comparators, relaxation oscillators, and sensor threshold detection in industrial and automotive-adjacent environments. The wide supply range makes it a natural fit for 5V, 12V, and 24V industrial rails. For design, always include a pull-up resistor on each open-collector output (typically 1k to 10k ohm), and add hysteresis with positive feedback when comparing slowly moving signals to avoid output chatter near the threshold. This page synthesizes datasheet parameters, drop-in alternatives, practical design notes, and application guidance not found together in the manufacturer datasheet.

RFQ Contact
LM2903P - Dual Differential Comparator, 30 V, PDIP-8 | Texas Instruments
LM2903P

LM2903P - Dual Differential Comparator, 30 V, PDIP-8 | Texas Instruments

The Texas Instruments LM2903P is a dual differential comparator with open-collector, rail-to-rail outputs, supplied in an 8-pin PDIP package. The device contains two independent voltage comparators designed for general-purpose signal conditioning, threshold detection, and simple control applications. The verified distributor and manufacturer data identifies the LM2903 as a dual differential comparator intended for operation from a single supply or dual supplies, with a maximum supply voltage rating of up to 38 V for the B-version family and a listed operating supply range of 2 V minimum for comparison devices in the same family. A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic result. The LM2903 family belongs to the broader comparator and analog signal-conditioning hierarchy, where open-collector outputs provide flexible interface options for pull-up resistors, relay drivers, lamp circuits, and low-voltage digital logic. Its differential inputs allow one signal to be monitored against a reference or another input, making the device suitable for window detection, current sensing, sensor thresholding, and industrial control circuits. The LM2903P uses two independent comparators, with output transistors capable of sinking current into an external pull-up network. The verified data identifies the output style as open-collector and rail-to-rail, while the family description confirms two independent voltage comparators and operation from a single power supply over a wide voltage range. The LM2903P is supplied through a tube package in the verified distributor result, making it appropriate for through-hole production and prototype boards rather than compact surface-mount assemblies. Typical uses include monitoring a control voltage, detecting an overvoltage or undervoltage condition, converting an analog sensor threshold into a logic event, and driving an alert or shutdown input. Because an open-collector output requires an external pull-up resistor, the output voltage is defined by the pull-up supply and resistor rather than by the comparator alone. Designers should also verify input common-mode limits, output sink current, supply-current requirements, and propagation delay for the exact operating conditions. The principal design consideration is that the LM2903P is a through-hole PDIP-8 comparator, not a low-power modern micropower comparator. Its application circuit must respect the device's supply voltage, input voltage, common-mode range, output pull-up arrangement, and maximum output current. This page combines the verified manufacturer and distributor information with practical application guidance and same-family replacement context for engineers evaluating an LM2903P design.

RFQ Contact
LM2903P-MAND - Dual Open-Collector Comparator | Texas Instruments
LM2903P-MAND

LM2903P-MAND - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903P-MAND is a dual differential comparator with two independent comparator channels and open-collector outputs, packaged in an 8-pin PDIP package. The device compares two input voltages at each channel and provides a logic-level indication of their relative relationship. Its through-hole PDIP package supports straightforward PCB assembly, prototyping, repair, and applications that favor accessible leads over a surface-mount footprint. A comparator is an analog signal-conditioning IC that occupies the comparator hierarchy within analog signal processing and broader semiconductor systems. Unlike an operational amplifier, a comparator is optimized for fast logic-level decisions and normally has open-collector outputs suited to pulling a wired bus or logic node high. The LM2903P-MAND contains two such channels, allowing a single component to monitor two thresholds, supervise two signals, or implement a window-style decision function. The principal features of the LM2903P-MAND are its dual-channel architecture, differential inputs, open-collector outputs, and PDIP-8 package. Each channel can use its non-inverting and inverting inputs around a common reference. The open-collector outputs require an external pull-up resistor when the output must actively drive a high voltage level. This arrangement also permits several open-collector outputs to share a bus when their operating conditions and logic polarity are compatible. The LM2903P-MAND belongs to the Texas Instruments LM2903 dual-comparator family. Its architecture supports operation from a single supply or split supplies, depending on the selected voltage limits and application requirements. Differential comparison is useful when the two inputs are referenced to the same signal source, such as a sensor divided into two scaled voltages. Open-collector outputs are particularly useful for relay, lamp, alarm, and industrial logic interfaces because they provide a straightforward way to sink current. Typical applications include industrial sensor threshold detection, overvoltage and undervoltage supervision, automotive electronics, battery monitoring, control-panel annunciation, and general-purpose digital control systems. The PDIP package is especially useful in equipment where long-term maintainability, socketed assembly, or hand rework is valuable. Designers should still account for the open-collector pull-up network and verify the common-mode, supply, and output-current limits against the manufacturer datasheet for the exact ordering code. For a new PCB, route the input traces away from switching nodes and connect a suitable pull-up resistor to each open-collector output. Confirm the input reference arrangement so the required high or low output polarity is obtained without reversing the channel logic. Because the MAND ordering suffix may denote a special qualification or temperature treatment, do not infer its production limits solely from the base LM2903 family designation; consult the exact MPN documentation. This product page organizes the dual-comparator function, verified package information, practical design notes, and same-footprint alternatives into an engineer-focused guide. It also highlights the distinction between the LM2903 family and the B-version with improved electrical specifications, helping PCB designers separate drop-in continuity from a functional upgrade.

RFQ Contact
LM2903PS-MAND - Dual Open-Collector Comparator | Texas Instruments
LM2903PS-MAND

LM2903PS-MAND - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM2903PS-MAND is a dual differential comparator with two independent comparator channels, an open-collector output architecture, and an 8-pin small-outline package. The LM2903 family is designed for general-purpose signal comparison and can operate from a single supply while also supporting split-supply arrangements. Its input common-mode range includes ground, making it useful in battery-powered and mixed-polarity systems where inputs may approach the lower supply rail. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level result indicating which input is higher. Within the semiconductor hierarchy, a comparator belongs to the broader operational-amplifier and signal-conditioning family, with the LM2903 providing two independently usable channels in one monolithic package. This integration reduces the component count and package footprint in threshold detection, sensing, and control circuits. The primary features of the LM2903PS-MAND are its dual-channel configuration, open-collector outputs, ground-referenced input capability, and ability to operate from either a single or split supply. Open-collector outputs are useful when the output must pull up to a system-specific voltage, interface with TTL or CMOS logic, or support wired-AND behavior. Each channel may also be used independently, allowing one device to compare two different signal pairs. In practical signal-path terms, the comparator evaluates a voltage present at its inverting or non-inverting input against a reference or threshold established by the other input. Its wide common-mode capability allows direct sensing of low-level signals referenced to ground. Designers should account for input and output timing, pull-up requirements, supply behavior, and the transition characteristics listed in the manufacturer datasheet when setting switching thresholds or driving downstream circuitry. Typical applications include battery threshold monitoring, sensor signal conditioning, window comparators, overvoltage detection, industrial control interfaces, and general-purpose digital decision logic. The two channels are particularly useful when a design needs two related comparisons, such as monitoring both a rising threshold and a falling threshold, or detecting upper and lower limits around a nominal operating point. For implementation, connect an appropriate pull-up resistor to each open-collector output and account for the resulting rise time when operating speed matters. Keep input and output routing compact to reduce sensitivity to interference, and confirm the device's operating-temperature, supply-voltage, and input-voltage limits against the requirements of the target application before releasing the PCB design. This product overview combines the device's core functionality with practical guidance on open-collector interfaces, dual-channel usage, threshold detection, and drop-in alternatives. It also provides comparison-focused engineering information intended to make component selection and PCB reuse faster than a distributor specification summary alone.

RFQ Contact
LM2903PSRG4 - Dual Differential Comparator | Texas Instruments
LM2903PSRG4

LM2903PSRG4 - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM2903PSRG4 is a dual differential comparator containing two independent comparator channels, with a 36 V maximum supply range, 0.4 mA typical supply-current drain per comparator, and an 8-pin SOIC package. It is designed for single-supply operation or dual-supply operation when the total supply span remains within 2 V to 36 V. A differential comparator is a semiconductor amplifier that compares two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM2903 family belongs to the broader hierarchy of analog comparator ICs, analog signal-conditioning ICs, and semiconductor devices. Its two channels can be used independently, allowing one package to monitor two thresholds or control two independent signals. The principal operating characteristics include a wide supply-voltage range, low supply-current drain independent of supply voltage, and a low input bias current of 25 nA. The open-collector output configuration allows each output to pull a logic signal low while an external pull-up resistor establishes the high state. This makes the device useful in interfaces requiring wired-AND behavior, relay-driver circuits, and systems that need a defined output voltage domain. The LM2903PSRG4 operates from -40°C to +125°C, supporting industrial temperature environments. Its two independent comparator sections can evaluate separate signal pairs without sharing internal signal paths. Because the outputs are open collector, the maximum output voltage is determined mainly by the pull-up network and external supply rather than by a fixed internal high-level voltage. The 8-pin SOIC footprint supports compact surface-mount layouts in industrial control, instrumentation, power-supply monitoring, and interface circuits. Typical uses include detecting overvoltage or undervoltage conditions, converting analog sensor thresholds into logic events, monitoring battery or power rails, and driving optocouplers or relay coils through suitable driver stages. The LM2903PSRG4 is particularly appropriate when the monitored signals remain within the comparator's input and supply limits and when an open-collector interface is acceptable. When designing the circuit, choose the pull-up resistor to balance sink-current capacity, rise time, and power dissipation. Confirm the output current, input common-mode range, input offset voltage, response time, and absolute maximum ratings against the manufacturer datasheet before applying the device to a new voltage range. Account for switching transients and provide stable ground-return paths to prevent comparator chatter. This product page organizes the LM2903PSRG4 specifications, package information, drop-in family alternatives, application guidance, and engineering design notes. It also provides a structured comparison for selecting a suitable comparator while preserving the same SOIC-8 footprint and pin arrangement.

RFQ Contact
LM2903PT - Dual Low-Power Voltage Comparator, +2V to +36V | STMicroelectronics
LM2903PT

LM2903PT - Dual Low-Power Voltage Comparator, +2V to +36V | STMicroelectronics

The STMicroelectronics LM2903PT is a low-power dual voltage comparator with two independent, single-pole comparators on a single monolithic substrate, supplied in an 8-pin TSSOP (8TSSOP) surface-mount package. It operates from a single +2 V to +36 V supply or from dual supplies of +/-1 V to +/-18 V, drawing only 0.4 mA of supply current independent of supply voltage, equal to 1 mW per comparator at +5 V. A voltage comparator is an amplifier IC that compares two input voltages and switches its output when the difference between them changes sign. In system terms a comparator sits at the base of the hierarchy of analog signal conditioning: comparator -> amplifier IC -> analog integrated circuit -> semiconductor, and it is the natural front end for threshold detection, sensor signalling and window monitoring. Because the LM2903 output is an open-collector style transistor stage, it interfaces directly with TTL, MOS and CMOS logic families and can pull a rail low without an external push-pull driver. Key features of the LM2903PT include a common-mode input voltage range that includes ground even when operated from a single supply, very low supply current drain of 0.4 mA, low input bias current of 25 nA typical, and low input offset current of +/-5 nA typical. The low offset current means the two comparators of the pair track each other closely, which matters when one channel is used as a reference and the other as the active comparator in a window-detector arrangement. The device is built on a bipolar monolithic process, which explains the wide supply range and the ability to accept input signals near and beyond ground. Two comparators share one package, so a single 8-pin TSSOP footprint can implement a full two-threshold window comparator, a dual-level battery monitor, or a pair of independent limit detectors for analog signals with only one board space increment. Typical applications include industrial control and instrumentation thresholds, battery-powered monitoring and protection circuits, motor and solenoid drive control loops, sensor interface modules, and consumer equipment power supervision. Because supply current is independent of the supply voltage, the part remains usable across wide battery-discharge ranges without the quiescent current rising as the cell voltage falls. When laying out the design, route the two input nets as short and separated as possible, keep the open-collector output pull-up resistor close to the device, and confirm that the logic family connected to the output can tolerate the pull-up voltage. Use the pin-description table in the STMicroelectronics datasheet when assigning PCB tracks. This page brings together the supply-voltage and input-current characteristics, drop-in alternatives that share the identical TSSOP-8 footprint, comparison tables and practical design notes that go beyond a bare parameter listing, helping engineers qualify the part quickly for industrial, automotive-adjacent and consumer designs.

RFQ Contact
LM2903PW - Dual Differential Comparator, 36V TSSOP-8 | TI
LM2903PW

LM2903PW - Dual Differential Comparator, 36V TSSOP-8 | TI

The Texas Instruments LM2903PW is a dual differential comparator with open-collector outputs, rated for supply operation up to 36 V, drawing a typical 0.4 mA of supply current per comparator, and housed in an 8-pin TSSOP package. It belongs to the industry-standard LM193/LM293/LM393/LM2903 comparator family trusted in automotive, industrial, and consumer designs. A comparator (also called a voltage comparator) is an analog building block that compares two input voltages and drives its output to indicate which is higher. It sits within the broader hierarchy of amplifier ICs and analog signal-chain components, bridging the gap between raw sensor signals and digital logic decisions. Unlike an operational amplifier used in closed-loop gain configurations, a comparator operates open-loop with very high gain, switching its output rail-to-rail between defined logic states. Key features of the LM2903PW include single-supply or dual-supply operation across a wide 36 V range, low supply-current drain that is largely independent of supply voltage, low input bias current of 25 nA typical per comparator, and low input offset current of 3 nA typical. The open-collector outputs allow wired-OR connections and direct interface with TTL, CMOS, and other logic families via a pull-up resistor. Architecturally, each comparator provides high differential gain with inputs that work down to the negative supply rail (ground in single-supply systems), enabling ground-referenced sensing. The common-mode input range extends to the positive supply minus about 1.5 V. A typical response time of approximately 1300 ns suits monitoring, threshold detection, and level-shifting tasks where microsecond-scale decisions are adequate. Typical applications include automotive sensor threshold detection, battery undervoltage lockout, zero-crossing detection for motor control, window comparators in industrial monitoring, and oscillator/timer circuits. The automotive temperature grade (up to +125 C ambient) makes the LM2903 family a default choice in vehicle environments. Design consideration: because outputs are open-collector, every output requires a pull-up resistor to the desired logic rail; choosing a lower pull-up resistance speeds rise time but increases power dissipation. This page adds engineering value beyond the datasheet: a parameter comparison against drop-in alternatives, practical design notes on pull-up sizing and hysteresis, application guidance, and sourcing FAQs consolidated in one place.

RFQ Contact
LM2903PWR - Dual Open-Collector Comparator | Texas Instruments
LM2903PWR

LM2903PWR - Dual Open-Collector Comparator | Texas Instruments

Texas Instruments LM2903PWR is a dual differential comparator with an open-collector output, rail-to-rail input capability, and a wide operating range of ±18V, or 36V total, in an 8-pin TSSOP package. The device contains two independent comparators, making it suitable for threshold detection, window comparison, industrial control, and signal-conditioning systems. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input rises above the inverting input. In the larger semiconductor hierarchy, the LM2903 belongs to the comparator and analog IC family, where its differential inputs, open-collector outputs, and wide supply tolerance support robust sensing across industrial voltage ranges. The LM2903PWR provides two independent comparison channels in one package. Its open-collector outputs can sink output current while remaining in a high-impedance state when inactive, allowing pull-up resistors to set the logic-high voltage and multiple comparator outputs to share a bus when wired appropriately. Rail-to-rail input operation extends the usable common-mode range toward the supply limits, which is valuable in battery-powered and industrial designs. The improved LM2903B family associated with this device is specified for operation up to 38V, an ESD rating of 2kV HBM, input offset voltage as low as 0.37mV, input bias current as low as 3.5nA, supply current of 200µA per comparator, and response time of 1µs. These characteristics improve on older LM393-family performance while retaining the established LM2903 function and pin arrangement. Typical uses include DC threshold monitors, overvoltage and undervoltage detection, sensor conditioning, window comparators, and industrial control logic. In a typical application, each comparator evaluates a signal against a reference generated by a resistor divider, while external pull-up resistors convert the open-collector output into a valid logic-high state. Layout should keep input traces short, route sensitive comparison nodes away from switching-node currents, and place input and reference-network components close to the device. A common ground reference and stable bypass capacitance are essential because comparator decisions depend on the difference between two input voltages. This page combines manufacturer device information, verified distributor listings, package identification, replacement analysis, and application-focused design guidance. It also distinguishes confirmed drop-in options from alternatives that cannot be installed on the same 8-pin TSSOP footprint without redesign.

RFQ Contact
LM2903PWRG3 - Dual Differential Comparator | Texas Instruments
LM2903PWRG3

LM2903PWRG3 - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM2903PWRG3 is a dual differential comparator containing two independent general-purpose comparator channels, a 2 V to 36 V single-supply operating range, and open-collector outputs in an 8-pin TSSOP package. According to the Texas Instruments LM2903 product information, each channel compares two differential inputs and can also operate from split power supplies spanning 2 V to 36 V. A differential comparator is an analog integrated circuit that evaluates the relative voltage between its inverting and non-inverting inputs. When the non-inverting input rises above the inverting input, the associated output transistor turns on; when the relationship reverses, the output transistor turns off. This complementary sensing function places the LM2903 in the amplifier and interface IC hierarchy, where comparator ICs convert small analog voltage differences into logic-level decisions for control, protection, and signaling systems. The LM2903 provides two independent channels in one package, reducing component count in designs requiring more than one threshold comparison. Its open-collector outputs permit wired connections and external pull-up resistors, providing flexibility for interfacing with TTL, CMOS, and other digital logic families. The 2 V to 36 V supply range supports both low-voltage control circuits and higher-voltage industrial systems, while the differential input arrangement helps monitor two sensed voltages without requiring a separate input amplifier. The PWRG3 ordering configuration is supplied in an 8-TSSOP surface-mount package for compact PCB layouts and automated assembly. Open-collector outputs require suitable pull-up arrangements when a logic-high output state is needed. Because both comparators share the same supply package while retaining independent inputs and outputs, designers can allocate the two channels to separate analog domains when those domains remain compatible with the device's common-mode and supply limitations. Typical uses include overvoltage and undervoltage detection, window monitoring, sensor threshold comparison, industrial control logic, and power-supply supervision. The two-channel organization is particularly useful in window comparators, where one channel establishes an upper threshold and the other establishes a lower threshold, or in systems where separate alert functions require independent decisions. When designing a PCB around the LM2903PWRG3, place input, output, and bypass connections to minimize noise coupling into the high-impedance comparison inputs. Select pull-up resistors according to the required sink current, rise time, and logic family. Verify common-mode range, supply polarity, and output-state requirements across temperature and supply tolerance before treating the comparator output as a guaranteed logic-high signal. This product page combines the Texas Instruments device information with package, application, sourcing, and replacement guidance. It also provides design-focused comparisons that help engineers distinguish ordering-grade, package, supply, and output-stage differences before selecting a pin-compatible replacement or integrating the device into a new analog control board.

RFQ Contact
LM2903PWRG4 - Dual Open-Collector Comparator | TI
LM2903PWRG4

LM2903PWRG4 - Dual Open-Collector Comparator | TI

Texas Instruments LM2903PWRG4 is a dual differential comparator with two independent open-collector outputs, a 38 V maximum supply rating, and an 8-TSSOP package. It operates from a single supply or from dual supplies when the total supply span is 2 V to 36 V. Its headline electrical characteristics include 0.37 mV low input offset voltage, 3.5 nA low input bias current, 200 uA supply current per comparator, and a 1 us response time. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM2903 belongs to the comparator hierarchy, within analog interface ICs and general-purpose semiconductor signal-conditioning devices. Its open-collector transistor output can sink current to a logic-low state while leaving the output node in a high-impedance state when the comparator is inactive. This architecture makes pull-up resistors and compatible pull-up voltage selection important parts of the surrounding circuit. Key features include two independent comparison channels, rail-to-rail input operation as identified for this device, and a wide supply-voltage range. The 0.37 mV input offset specification helps limit the input differential needed to change an output, while the 3.5 nA bias-current specification reduces disturbance on high-impedance sensing nodes. The 1 us response time is useful for threshold detection, signal conditioning, and control loops that require a defined transition interval. The device supports single-supply operation and dual-supply operation, giving designers flexibility in industrial, automotive, and embedded systems. Its open-collector outputs can drive multiple pull-up domains when appropriate system-level conditions are met, although each connected node must remain within the device's applicable electrical limits. The 200 uA supply-current value per comparator also makes the part suitable for power-conscious monitoring and control circuits where continuous comparator operation is required. Typical uses include overvoltage and undervoltage detection, sensor threshold conditioning, industrial control logic, automotive interface circuits, window or level comparison, and general-purpose decision logic. In each case, resistor selection around the open-collector outputs and proper input common-mode limits are central to obtaining predictable operation. Design with the input common-mode range, supply voltage, output pull-up voltage, and input differential polarity together. Keep sensitive comparison traces short, provide stable bypassing near the supply pins, and account for the open-collector output's rise time, which is influenced by the pull-up resistor and total node capacitance rather than only by the comparator response time. This page combines manufacturer specifications, packaging details, application guidance, and qualified drop-in comparison information to support faster component selection and PCB implementation. It also highlights the electrical details that distinguish this 8-TSSOP comparator from alternatives with different package or interface requirements.

RFQ Contact
LM2903Q2T - Dual Low-Power Voltage Comparator | STMicroelectronics
LM2903Q2T

LM2903Q2T - Dual Low-Power Voltage Comparator | STMicroelectronics

STMicroelectronics LM2903Q2T is a dual, independent, low-power voltage comparator designed for single-supply or split-supply operation across a wide voltage range. The device is identified as a standard general-purpose comparator with open-collector, rail-to-rail outputs and is packaged in an 8-DFN 2 x 2 mm package. Its two comparator channels can be used separately or together for threshold detection, overvoltage and undervoltage monitoring, signal conditioning, and basic analog control functions. A voltage comparator is an analog mixed-signal IC that compares an input voltage with a reference voltage and changes its output state when the relationship between those voltages changes. The LM2903 belongs to the comparator hierarchy, which sits between general-purpose analog signal conditioning and system-level protection or control. Its open-collector outputs can be pulled up to a suitable supply rail, allowing interface compatibility with TTL, CMOS, MOS, and other digital logic when the output circuit is designed correctly. The LM2903Q2T is specifically suited to low-power applications because the manufacturer identifies it as a low-power dual comparator. Its two independent channels provide flexibility in battery-operated equipment, industrial sensing, automotive electronics, consumer products, and embedded control systems. The 2 x 2 mm DFN package also supports compact layouts where board area is limited, although its exposed thermal pad and fine-pitch assembly requirements require careful PCB design. The comparator output architecture is open collector, so an external pull-up resistor is generally required to establish a high output level. The output transistor can sink current when the comparator condition is met, while the pull-up network determines the high-state voltage and rise time. This configuration is useful for wired-AND signal aggregation, but it also means that the output voltage, transition timing, and allowable sink current depend on the external resistor and load. The LM2903 family is designed for operation from a single supply or split supplies, making it appropriate for systems that require comparison of signals referenced to ground or signals that exceed ground when both positive and negative rails are available. Because the exact electrical limits, common-mode range, output timing, and automotive qualification details are not shown in the retrieved product summaries, final circuit design should use the manufacturer datasheet and its recommended operating conditions. A compact application should include local input filtering when sensor leads are long or noisy, a defined output pull-up, and adequate copper around the exposed pad when both channels operate continuously. The small DFN package can reduce board space, but its compact size does not eliminate thermal or assembly constraints. Use the manufacturer pin configuration and land pattern when assigning inputs, outputs, supply pins, and the exposed pad. This page combines the LM2903Q2T product identity, verified manufacturer and distributor references, application guidance, package considerations, and design notes. It also explains why open-collector operation, power-supply topology, output pull-up design, and thermal layout determine whether the comparator works reliably in a real system.

RFQ Contact
LM2903QDG4 - Dual Differential Comparator, 36 V | Texas Instruments
LM2903QDG4

LM2903QDG4 - Dual Differential Comparator, 36 V | Texas Instruments

The Texas Instruments LM2903QDG4 is a dual differential comparator containing two independent comparison channels, operating from a single 2 V to 36 V supply or dual supplies whose total voltage spans 2 V to 36 V. The device accepts differential input voltage and uses open-collector outputs compatible with TTL, CMOS, and MOS logic. It is packaged for surface-mount assembly in an 8-pin SOIC package. A differential comparator is an analog interface integrated circuit that compares two input voltages and changes its output state according to their relative polarity. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits, where it bridges low-level sensor or signal voltages to a digital logic domain. Each half of the device can operate independently, allowing two comparisons in one package when the power supplies and input signals share a suitable common range. The principal features are dual independent comparators, a wide 2 V to 36 V operating range, open-collector outputs, and logic compatibility with TTL, CMOS, and MOS devices. The open-collector architecture gives the output a defined pulled-up state when the output transistor is off and allows multiple open-collector outputs to share a wired bus when suitable, provided each output has its own pull-up path. The operating-temperature grade extends from -40 °C to 125 °C for industrial temperature conditions. Each comparator uses a differential input stage and an open-collector output stage. A positive differential input produces the corresponding output state, while the magnitude and polarity of the differential input determine switching behavior. Because the outputs are open collector, external pull-up resistors are required for normal TTL or CMOS-compatible operation. The pull-up value controls rise time, power consumption, and susceptibility to bus capacitance, so it must be selected with the driven load and operating speed in mind. Typical uses include monitoring a sensor threshold, detecting overvoltage or undervoltage conditions, comparing an analog measurement with a reference, and providing an open-collector signal to a microcontroller or logic gate. The wide supply range is useful for industrial control systems, automotive-adjacent sensing circuits, power-supply monitoring, and test equipment where input signals may exceed conventional low-voltage logic rails. PCB layout should keep the exposed routes short and provide a stable ground reference close to the comparator. Place input and output components according to the manufacturer application guidance, and avoid routing high-current or switching-node copper directly beside the differential inputs. Pull-up resistors should connect to the intended logic supply rather than the comparator supply when separate output-interface voltage is required. This page combines the manufacturer's device information, package details, operating limits, direct drop-in candidates, comparison parameters, and practical implementation guidance. It also identifies which electrical details require confirmation in the LM2903 family datasheet before production release.

RFQ Contact
LM2903QDGKRQ1 - Dual 36V Automotive Comparator | Texas Instruments
LM2903QDGKRQ1

LM2903QDGKRQ1 - Dual 36V Automotive Comparator | Texas Instruments

The Texas Instruments LM2903QDGKRQ1 is an AEC-Q100 Grade 0 and Grade 1 automotive dual differential comparator with open-collector outputs, operating from 3 V to 36 V and supplied in an 8-pin VSSOP package. The device provides two independent comparison channels, a common supply range of 3 V to 36 V, and input common-mode operation extending to the supply rails. According to the TI LM2903-Q1 product page, the LM2903-Q1 family is designed for cost-sensitive automotive and industrial systems requiring high-voltage tolerant inputs and open-collector outputs. A comparator is an analog integrated circuit that evaluates two input voltages and produces a digital output indicating whether the non-inverting input is above or below the inverting input. Within the broader hierarchy, the LM2903-Q1 is a differential comparator, a general-purpose analog IC, and a member of the power-management and signal-conditioning semiconductor category. Its open-collector output structure allows several comparator outputs to be wired together for wired-AND operation and requires an external pull-up resistor for normal logic-level operation. Key characteristics include dual-channel operation, a 36 V maximum supply capability, and open-collector outputs suitable for automotive battery-powered systems. The AEC-Q100 Grade 0 and Grade 1 qualification supports demanding automotive environments, while the wide input voltage range reduces the need for separate input protection in many 12 V, 24 V, and 36 V system architectures. The 8-pin VSSOP package also supports compact PCB layouts where space is limited. The LM2903-Q1 architecture is designed for general-purpose threshold detection rather than high-speed waveform discrimination. Its differential input stage allows sensing of small analog changes, and the open-collector outputs can directly pull up a logic bus, drive a relay driver, or interface with automotive transceiver inputs. The open-collector configuration also provides wired-AND behavior when multiple comparator channels share a pull-up resistor. Typical applications include automotive battery monitoring, overvoltage and undervoltage detection, window or door sensing, sensor conditioning, and industrial control systems. In battery systems, the wide supply tolerance supports operation across load dump and automotive electrical-environment conditions when paired with appropriate protection. In control logic, two independent channels can monitor separate thresholds or implement a window comparator using external resistor networks. When designing the PCB, route the comparator inputs away from switching nodes and high-current return paths because input offset voltage can make nearby interference appear as a false state transition. Place the pull-up resistor close to the open-collector output and verify that its value keeps the logic rise time within the receiving device's limits. Automotive designs should also include the transient-protection components required by the complete vehicle electrical system rather than relying on the comparator alone for surge suppression. This page consolidates the verified package, voltage, output, qualification, and lifecycle information with application guidance, comparison parameters, and design notes that support faster component selection and PCB implementation.

RFQ Contact
LM2903QDRG4 - 36 V Dual Comparator | Texas Instruments
LM2903QDRG4

LM2903QDRG4 - 36 V Dual Comparator | Texas Instruments

The Texas Instruments LM2903QDRG4 is a dual differential analog comparator with two independent comparison channels, an open-collector output, and an 8-pin SOIC package. The device supports single-supply or dual-supply operation over a wide voltage range up to 36 V, while each comparator typically consumes 0.4 mA. It is specified for an ambient temperature range of -40°C to +125°C. An analog comparator is an integrated circuit that compares two input voltages and produces a digital-level result indicating which input is higher. The LM2903 belongs to the comparator hierarchy within amplifier and interface ICs, providing a simple alternative to a general-purpose operational amplifier used only for voltage comparison. Its open-collector outputs can sink external pull-up current and support wired logic, level translation, or open-drain bus arrangements. The two comparators operate independently, allowing one package to implement two sensing or threshold functions. Low typical input bias current of 25 nA helps minimize disturbance on high-impedance sensor circuits. The low supply-current drain, reported as 0.4 mA typical per comparator, is useful in battery-powered equipment where continuous comparator consumption affects available operating time. The LM2903 can operate from a single positive supply or from two supplies when their voltage difference is between 2 V and 36 V. In dual-supply use, the positive supply must remain at least 1.5 V above the negative supply referenced by the device. This flexibility supports comparator designs around 5 V, 12 V, 24 V, and split-rail industrial systems. Typical applications include battery threshold detection, industrial sensor interfaces, overvoltage and undervoltage supervision, window comparators for analog signals, and open-drain alarm signaling. Because each output is open collector, a pull-up resistor is required when the output must drive a conventional logic-high state. The open-collector architecture also permits several comparators to share a common pull-up when wired logic is appropriate. PCB design should keep input and output traces short, provide a solid ground return, and place input filtering close to the relevant pins. Because an open-collector output cannot source current, size the pull-up resistor to balance rising time, signal current, and power dissipation. The -40°C to +125°C rating supports industrial temperature ranges, although the complete system still requires suitable thermal verification. This product page combines the exact LM2903QDRG4 ordering information with package, pinout, sourcing, comparison, and application guidance. It helps engineers distinguish verified pin-compatible options from devices that merely use a similar 8-pin package but differ in electrical behavior, qualification, or supply requirements.

RFQ Contact
LM2903QDRG4Q1 - Dual Comparator | Texas Instruments
LM2903QDRG4Q1

LM2903QDRG4Q1 - Dual Comparator | Texas Instruments

Texas Instruments LM2903QDRG4Q1 is an automotive dual differential comparator containing two independent comparator channels, with an 8-SOIC package, a 2 V to 36 V supply-voltage range, open-collector outputs, and an operating-temperature range of -40°C to +125°C. The device supports single-supply operation and dual-supply operation when the supply difference and common-mode requirements are satisfied. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The comparator category belongs to the broader amplifier IC and signal-conditioning hierarchy, where open-collector outputs are useful for wired logic, system-level signaling, and driving external pull-up networks. The LM2903-Q1 family combines independent channels with automotive qualification for applications requiring reliable operation across extended temperatures. Key electrical characteristics include a maximum input-offset voltage of 7 mV at 5 V, a maximum input-bias current of 0.25 µA, typical output current of 20 mA, and maximum quiescent current of 2.5 mA. Its differential architecture supports sensing whether one voltage is above or below another without requiring a feedback network. The open-collector output can sink current while remaining in a high-impedance state when the output transistor is off. The two channels operate independently, allowing one device to implement two threshold decisions, window-detection functions, or complementary monitoring functions. A supply range extending to 36 V is valuable in automotive and industrial systems where the comparator may be connected to protected battery-derived or higher-voltage signal rails. The low input-bias current helps reduce errors when sensing high-impedance sources, while the specified offset limit establishes the basic threshold-accuracy boundary. Typical applications include automotive battery and power-rail supervision, sensor threshold detection, overvoltage and undervoltage indication, window comparators, and digital-control interfaces. The open-collector architecture also allows multiple comparators to share a pull-up resistor when wired logic is acceptable. External pull-up selection must account for the required sink current, rise time, bus capacitance, and system-level fault conditions. Designers should account for input common-mode limits, supply polarity, output pull-up placement, and unused-channel handling. Place the pull-up resistor near the open-collector output or system bus, and verify that the 20 mA typical output-current capability covers the worst-case sink demand. The manufacturer datasheet and pin-description table remain the controlling references for connection, common-mode range, and package details. This product page combines manufacturer specifications, package information, drop-in replacement guidance, and practical application guidance. It supports faster component selection while preserving the electrical checks required for reliable comparator-based sensing and control systems.

RFQ Contact
LM2903QDRQ1 - 36V Automotive Dual Comparator | Texas Instruments
LM2903QDRQ1

LM2903QDRQ1 - 36V Automotive Dual Comparator | Texas Instruments

The Texas Instruments LM2903QDRQ1 is an AEC-Q100-qualified automotive dual differential comparator with two independent comparison channels, a 2 V to 36 V single-supply operating range, and open-collector outputs in an 8-pin SOIC package. It is designed for high-voltage industrial and automotive systems where two independent comparator channels are required in a compact package. A differential comparator is an analog integrated circuit that compares the voltage at its inverting input with the voltage at its non-inverting input and changes its output state when the input difference crosses a defined threshold. The comparator belongs to the broader hierarchy of analog ICs, signal-conditioning ICs, and semiconductor devices. Its open-collector architecture allows the output to be pulled up to a system-compatible logic voltage rather than being limited to the IC supply rail. Key electrical characteristics include a typical input offset voltage of 2 mV, a typical input bias current of 25 nA, and a supply current of 0.4 mA per comparator. Each channel provides one push-pull-compatible input stage and an open-collector output that is compatible with TTL, MOS, and CMOS logic families. The single-supply operating range is 2 V to 36 V, while operation from dual supplies is possible when the total supply difference is between 2 V and 36 V. The LM2903-Q1 family combines a wide supply range with low supply current and AEC-Q100 Grade 0 and Grade 1 options. These characteristics make it suitable for sensing circuits connected to higher-voltage buses than those commonly handled by low-voltage mixed-signal comparators. The open-collector outputs also simplify wired-interface and level-shifting arrangements when an external pull-up resistor is used. Typical applications include automotive battery and power-system monitoring, industrial control systems, motor and solenoid feedback circuits, window or lighting controllers, overcurrent and overvoltage detection, and general-purpose threshold sensing. Two channels in one package reduce board area when independent comparison functions are required. The main design consideration is the open-collector output. Every output requires a pull-up resistor to the desired logic rail, and the pull-up must be sized against the output sink current and expected switching rate. Designers should also verify the input common-mode range at the selected supply voltage before committing the circuit to automotive or industrial rail conditions.

RFQ Contact
LM2903QM8-13 - Dual 36V Comparator | Diodes Inc.
LM2903QM8-13

LM2903QM8-13 - Dual 36V Comparator | Diodes Inc.

The Diodes Incorporated LM2903QM8-13 is a dual differential voltage comparator designed for automotive and industrial systems, with two independent comparator channels, a 36 V maximum supply rating, 2 mV input offset voltage, 25 nA input bias current, and an 8-MSOP package. It supports input common-mode ranges that include ground and a differential input range equal to the supply voltage. A voltage comparator is an analog integrated circuit that compares two input voltages and switches its output when the difference crosses a defined threshold. The LM2903 belongs to the broader comparator hierarchy within analog ICs and signal-conditioning electronics. Each of its two channels includes a noninverting input, an inverting input, and an output, allowing one device to perform threshold detection, window comparison, or independent level sensing. Key features include low input offset voltage, low input bias current, 5 nA output leakage current, and low output saturation voltage of 200 mV at 4 mA. The LM2903QM8-13 is identified as an automotive-compliant Q-grade device, while its lead-free construction and full RoHS compliance support environmentally constrained production programs. Its open-collector-style output is compatible with TTL, MOS, and CMOS logic systems. Technically, the device combines precision differential input handling with practical supply-voltage tolerance. The comparators can operate across a broad input range because the common-mode input voltage includes ground while the differential input range can extend to the power-supply voltage. This makes the device useful where sensing signals may approach 0 V or where input stages share the comparator supply rail. Designers should still verify absolute maximum conditions and output pull-up arrangements for the specific operating environment. Typical uses include automotive battery and rail monitoring, sensor threshold detection, window comparators, overvoltage and undervoltage detection, industrial control thresholds, and digital-interface signaling. The dual-channel organization saves board area when two independent decisions are required, while the 8-MSOP package supports compact surface-mount assemblies. For implementation, use a suitable pull-up resistor on each open-collector output and account for output-leakage effects when the output is high. Keep sensitive input traces short, provide a stable local supply connection, and verify common-mode, differential, and absolute-maximum limits before applying large transient voltages. This page combines the manufacturer specifications, automotive qualification details, package information, drop-in alternatives, and practical circuit guidance into a design-oriented reference for engineers evaluating the LM2903QM8-13.

RFQ Contact