Products (44,000+)

LM2903YPT - Dual 36V Low-Power Comparator | STMicroelectronics
LM2903YPT

LM2903YPT - Dual 36V Low-Power Comparator | STMicroelectronics

The STMicroelectronics LM2903YPT is a dual low-power voltage comparator with two independent channels, an open-collector output stage, and operation from a single 2 V to 36 V supply or split supplies of ±1 V to ±18 V. The device is packaged in an 8-pin TSSOP and is identified as rail-to-rail by its distributor listing. A voltage comparator is an analog interface IC that compares two input voltages and produces a digital logic state indicating which input is higher. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its two channels can operate independently, making it suitable for threshold detection, window sensing, level translation, and basic control loops that require only polarity rather than an analog amplified output. The LM2903YPT features a very low supply current of 0.4 mA, described as independent of supply voltage. Operation at a 5 V supply corresponds to approximately 1 mW per comparator. Its low 25 nA typical input bias current and ±5 nA typical input offset current reduce errors when the sensing source has high source impedance. The open-collector outputs also permit wired connection to a common pull-up when an application requires a shared bus. The LM2903 architecture supports wide supply flexibility while retaining low power consumption. Each comparator has differential inputs and an independently controlled open-collector output. Because the output transistor can remain off, the effective output state depends on the external pull-up resistor, supply voltage, and leakage current. This architecture provides compatibility with digital logic but requires suitable pull-up placement and accounting for bus rise time. Typical uses include industrial sensor interfaces, battery-powered monitoring circuits, overvoltage and undervoltage detection, window comparators, and control systems operating across widely varying supply voltages. Two channels can be combined to form a window detector, with one comparator monitoring the upper threshold and the other monitoring the lower threshold. In automotive, industrial, or instrumentation systems, the low supply current helps limit standby power while the broad supply range simplifies power architecture. A key design consideration is output pull-up selection. The resistor must pull the open-collector node high without exceeding the output current limit, while keeping rise time acceptable for the receiving logic. Input common-mode limits, output timing, and absolute maximum ratings should be checked against the manufacturer datasheet for the exact operating conditions. The unused comparator channel should be configured according to the recommended application guidance rather than left floating. This product page combines the exact LM2903YPT ordering information with technical specifications, package and pin guidance, sourcing instructions, and practical comparison notes. It also highlights the restrictions that matter when evaluating a replacement: voltage range, output architecture, channel count, package footprint, temperature grade, and timing must all be compatible.

RFQ Contact
LM2903YQ3T - 36V Dual Comparator | STMicroelectronics
LM2903YQ3T

LM2903YQ3T - 36V Dual Comparator | STMicroelectronics

The STMicroelectronics LM2903YQ3T is a low-power dual voltage comparator with two independent comparison channels, a 2 V to 36 V single-supply range, and an open-collector rail-to-rail output in an 8-DFN 2 mm × 2 mm package. Each channel can compare an input signal against another signal, while the open-collector outputs provide flexible interface options for digital and analog control systems. A voltage comparator is a semiconductor device that compares two input voltages and changes its output state when one input crosses the other. The LM2903 belongs to the comparator hierarchy, which includes general-purpose comparators, differential comparators, and analog interface ICs. Its dual-channel architecture lets one device perform two independent threshold decisions, reducing component count in industrial control, automotive electronics, and low-power monitoring systems. Key characteristics include a wide single-supply operating range of 2 V to 36 V, dual-supply operation from ±1 V to ±18 V, and very low supply current of 0.4 mA. The typical input bias current is 25 nA, while the typical input offset current is ±5 nA. The open-collector outputs support wired-AND arrangements and require an external pull-up when the comparator must drive a logic input. Automotive-grade versions of this device family are associated with AEC-Q100 qualification. The two internal comparators are electrically independent, allowing separate signal paths within the same package. Rail-to-rail input behavior and low input bias current are useful when sensing source voltages that vary close to either supply rail. The low supply current also reduces power consumption in battery-powered systems, although propagation delay and output pull-up selection remain important when switching speed is critical. Typical applications include automotive battery and power-rail monitoring, industrial sensor threshold detection, overvoltage and undervoltage protection, window-comparator circuits, and logic-level translation between analog sensing nodes and digital control circuits. Its 2 mm × 2 mm DFN8 package supports compact board layouts when adequate copper area and controlled assembly are available. Designers should verify the complete pin assignment and exposed-pad requirements in the manufacturer datasheet before layout. Place input and output components close to their associated pins, provide a suitable pull-up for each open-collector output, and use stable reference sources when threshold accuracy matters. Confirm that signal amplitudes, common-mode range, supply limits, and automotive qualification requirements suit the target circuit. This product page consolidates the manufacturer electrical characteristics, package details, verified sourcing links, practical application guidance, and drop-in-replacement assessment. It also highlights the key limitation that a replaceable device must match both the 8-DFN footprint and pin behavior, rather than merely offering similar comparator performance.

RFQ Contact
LM2903YST - Dual 36V Low-Power Comparator | STMicroelectronics
LM2903YST

LM2903YST - Dual 36V Low-Power Comparator | STMicroelectronics

The STMicroelectronics LM2903YST is a dual low-power voltage comparator with two independent open-collector outputs, a 2 V to 36 V single-supply range, and support for dual supplies from ±1 V to ±18 V. The device is packaged in an 8-pin MiniSO/TSSOP package and is intended for low-voltage, low-power signal conditioning, threshold detection, and industrial control applications. A voltage comparator is an analog integrated circuit that compares an input voltage with a reference voltage and changes its output state according to the polarity of the difference. The LM2903 contains two independent comparator channels. Within the broader semiconductor hierarchy, it is an analog comparator, an interface IC, and a signal-conditioning device commonly used between sensors, switching circuits, and digital control logic. Key features include a supply current of 0.4 mA that remains independent of supply voltage, low input bias current of 25 nA typical, and low input offset current of ±5 nA typical. The open-collector outputs permit wired-AND connections and require an external pull-up resistor. A typical propagation delay of 1.3 µs supports threshold and switching functions, while the wide supply range accommodates industrial and automotive-style supply conditions. Each comparator has its own non-inverting input, inverting input, and open-collector output. The channels share the supply and ground pins but remain electrically independent for signal comparison. Operation from a single supply or split dual supplies gives designers flexibility when working with bipolar sensor signals, positive-only rails, or systems whose input range extends close to ground. Typical uses include sensor threshold detection, battery and power-supply monitoring, industrial control interfaces, automotive signal conditioning, window or level comparisons, and general-purpose logic qualification. The low 0.4 mA supply-current characteristic is particularly useful in continuously powered equipment where every increment of standby current affects system architecture. Designers should account for the open-collector output when selecting a pull-up resistor and logic supply voltage. Input common-mode limits, output saturation behavior, and the 1.3 µs response time must also be checked against the propagation delay allowed by the surrounding system. The manufacturer datasheet provides the authoritative pin assignments, electrical limits, and test conditions. This page combines operating limits, package details, comparison data, replacement guidance, and practical design notes to support component selection, schematic review, PCB implementation, and sourcing for the LM2903YST.

RFQ Contact
LM2904ADMG - Dual 26V Low-Power Op Amp | onsemi
LM2904ADMG

LM2904ADMG - Dual 26V Low-Power Op Amp | onsemi

The onsemi LM2904ADMG is a dual, general-purpose operational amplifier designed for low-power signal-conditioning applications over a 3 V to 26 V supply range. It provides two amplifier circuits, a common-mode input range that extends to ground or VEE, and operation from either a single supply or split supplies. The device is supplied in an 8-MSOP package and is specified for temperatures from -40°C to +105°C. An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify the difference between two input voltages. The LM2904 family belongs to the broader hierarchy of voltage-feedback operational amplifiers, analog amplifiers, and integrated signal-chain devices. Its common-mode capability makes it useful when signals approach the lower supply rail, while dual integration reduces board area in circuits requiring two independent amplifier channels. Key operating characteristics include a low-power architecture, a 3 V to 26 V supply-voltage capability, and a slew rate of 0.6 V/µs. The 8-MSOP package provides a compact surface-mount option for industrial and embedded equipment. Its specified temperature range supports applications across extended commercial and industrial environments. Designers should verify gain-bandwidth, input-bias-current, output-current, noise, and input-offset parameters against their operating conditions before finalizing a high-impedance or precision design. The LM2904ADMG uses the circuit design established for quad operational amplifiers, with two amplifiers per package. Its common-mode input voltage range extending toward ground or VEE is particularly useful in single-supply sensor interfaces, transimpedance stages, filters, and low-level signal amplifiers. The split-supply option permits operation around a zero-volt reference, while single-supply operation simplifies portable and industrial control systems. Typical applications include current monitoring, sensor conditioning, audio preamplification, active filtering, and general-purpose analog signal processing. In a current-sensing application, the device can amplify the voltage developed across a low-value shunt while operating from a split supply. In a sensor interface, the common-mode range allows closer proximity to the lower rail than a conventional bipolar input amplifier. Input and output stability should be checked with the external resistor and capacitance values used in the final circuit. A key design consideration is power-supply decoupling. Place a suitable bypass capacitor close to the supply pins and route return current through a low-impedance ground path. Avoid excessive output loading and confirm that the selected feedback network preserves the required gain-bandwidth and phase-margin behavior. For AC-coupled inputs, add suitable input bias-current compensation when source resistance is high. This page combines the LM2904ADMG electrical identity, package and temperature information with replacement guidance, comparison parameters, and practical design considerations. It also identifies which replacement candidates preserve the 8-MSOP footprint and where application-specific validation remains necessary.

RFQ Contact
LM2904ADMR2G - Dual 1 MHz Op Amp, 8-MSOP | onsemi
LM2904ADMR2G

LM2904ADMR2G - Dual 1 MHz Op Amp, 8-MSOP | onsemi

onsemi LM2904ADMR2G is a dual general-purpose operational amplifier with two amplifiers in an 8-MSOP package. It operates from single or split supplies, accepts input common-mode voltages extending to ground or VEE, and provides approximately 1 MHz gain-bandwidth product for general analog signal conditioning. The device is specified for low supply-current drain, low input offset voltage, low input bias current, and internal frequency compensation, making it suitable for applications that do not require rail-to-rail input or output operation. A dual operational amplifier combines two independent amplifier channels in one package. Operational amplifiers are active analog devices used to amplify, buffer, compare, or filter signals. They belong to the broader semiconductor hierarchy of integrated circuits, analog ICs, amplifiers, and operational amplifiers. The LM2904 family is commonly used for industrial control, sensor interfaces, audio signal paths, and low-frequency analog processing where economical dual-channel operation is useful. Key characteristics include a 3 MHz? No. The device has a 1 MHz gain-bandwidth product according to the manufacturer product description, low power drain, common-mode input voltage range extending to ground/VEE, and support for both single-supply and split-supply operation. The 8-MSOP package provides a compact surface-mount footprint for dual-channel analog designs. The LM2904ADMR2G is an active onsemi part according to the listed product information. The LM2904ADMR2G uses internally compensated bipolar amplifier circuits. Internal compensation removes the need for an external frequency-compensation network in ordinary closed-loop configurations. Its common-mode behavior is appropriate for many industrial and embedded systems where inputs remain above the negative supply rail, but the design should be checked against the datasheet limits before operating close to the positive rail or outside the specified supply range. Typical uses include instrumentation buffers, sensor amplifiers, active filters, comparators, audio preamplifier stages, and low-frequency control loops. In a single-supply system, the negative supply pin is connected to ground, while split-supply systems can use positive and negative rails. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet guidance. The principal design consideration is common-mode and output-range limitation. Unlike modern rail-to-rail-input amplifiers, the LM2904 family is not intended to cover the entire supply range at the input. Verify input common-mode voltage, output swing, supply current, stability, and noise performance against the application requirements. This page summarizes the part family, package, pinout, application considerations, and engineering-focused comparisons for design review and sourcing.

RFQ Contact
LM2904AHYPT - Dual Low-Power Op Amp | STMicroelectronics
LM2904AHYPT

LM2904AHYPT - Dual Low-Power Op Amp | STMicroelectronics

STMicroelectronics LM2904AHYPT is a low-power, dual bipolar operational amplifier with two independent amplifiers, internally compensated frequency compensation, and an 8-TSSOP package. The device is designed for general-purpose signal-conditioning applications where two amplifiers are required on one board. The verified product information identifies a single-ended, two-circuit amplifier configuration in an 8-pin TSSOP. A dual operational amplifier combines two independent amplifier sections in one package. In the broader semiconductor hierarchy, an operational amplifier is an analog integrated circuit used within the amplifier and signal-conditioning family. Each LM2904AHYPT section provides gain, filtering, buffering, or error amplification, while the common package can reduce board area and simplify component procurement for dual-channel circuits. The principal advantages of this device are its low-power bipolar construction, dual-channel organization, and internally compensated architecture. Internal compensation removes the need for external frequency-compensation components in standard closed-loop operation. The 8-TSSOP package also offers a compact surface-mount format suitable for high-density analog and embedded-control boards. These characteristics make the device useful when a general-purpose amplifier must operate without external compensation networks. Each amplifier section operates independently, allowing one channel to process a sensor signal while the other handles a control, feedback, or monitoring function. The LM2904 family is associated with approximately 100 dB open-loop gain, 1.1 MHz gain-bandwidth behavior, and 20 nA input bias current. Since the exact limits for every electrical condition are not listed on the product page, designers should confirm voltage, current, common-mode, and temperature limits against the manufacturer datasheet before final circuit sign-off. Typical uses include low-frequency sensor conditioning, buffer stages, active filters, differential signal amplification, and general embedded analog interfaces. Because the package contains two amplifiers, the device can consolidate matching channels in instrumentation, industrial control, audio preamplification, and test-equipment input stages. TSSOP-8 placement is particularly useful when component count and routing density are important. For layout, place each decoupling capacitor close to the corresponding supply pins and route input and feedback paths away from switching nodes. Confirm output swing, input common-mode range, stability, and load drive at the actual supply voltage. If a replacement uses the same footprint, verify that the enable, shutdown, slew-rate, and output-current characteristics remain compatible with the original design. This page combines the manufacturer device identity, verified distributor descriptions, package information, family-level operating characteristics, and practical replacement guidance into an engineering-focused reference for evaluating the LM2904AHYPT.

RFQ Contact
LM2904AM8-13 - Dual 700 kHz Op Amp | Diodes Incorporated
LM2904AM8-13

LM2904AM8-13 - Dual 700 kHz Op Amp | Diodes Incorporated

Diodes Incorporated LM2904AM8-13 is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, supplied in an 8-MSOP package. The device contains two independent, high-gain amplifiers and supports operation from a single supply or split supplies. Its specified operating range extends to ±18 V, equivalent to a total supply voltage of 36 V. This combination of dual-channel operation, wide supply capability, and surface-mount packaging makes the LM2904AM8-13 suitable for general-purpose signal conditioning across industrial, instrumentation, analog control, and embedded systems. An operational amplifier is a high-gain differential amplifier that uses negative feedback to control gain, filtering, amplification, buffering, or analog signal conversion. The dual-amplifier configuration reduces the number of active devices and board area needed when two independent analog channels are required. The LM2904AM8-13 belongs to the operational-amplifier hierarchy, where it sits below precision instrumentation amplifiers and above general-purpose discrete analog signal-conditioning functions. The LM2904 series is identified as a general-purpose amplifier family with very low input-offset voltage relative to many older general-purpose op amps. The two channels share an 8-MSOP package while retaining independent inputs and outputs. A 700 kHz gain-bandwidth product supports general-purpose closed-loop operation at moderate signal frequencies, and the ±18 V supply capability provides useful headroom for circuits using higher signal amplitudes. These characteristics make the part appropriate where low cost, channel density, and supply-voltage flexibility are more important than rail-to-rail input or output operation. The common operating topology places positive and negative feedback around each amplifier, setting closed-loop gain through external resistors. Because the device is intended for broad industrial signal conditioning, designers should verify the required input common-mode range, output swing, output-current capability, input-bias behavior, and stability against the exact operating conditions. The manufacturer datasheet provides the electrical limits and characteristic curves needed to select suitable feedback resistors, bypass capacitors, and external load conditions. Typical uses include sensor-interface conditioning, low-frequency active filters, differential-input stages, transducer amplifiers, analog control loops, and general instrumentation. Industrial data-acquisition systems can use one channel for signal conditioning while using the second channel for biasing, monitoring, or an auxiliary gain stage. The device is also appropriate for compact embedded analog subsystems where an 8-MSOP package reduces board footprint compared with two separate single-amplifier packages. When laying out the circuit, place bypass capacitors close to the supply pins and route feedback components close to their associated amplifier inputs and outputs. Avoid long parallel feedback traces, particularly when operating near the device's 700 kHz gain-bandwidth limit. Check whether the input source can develop voltages outside the specified common-mode range, because general-purpose op amps are not automatically rail-to-rail devices. This product page combines the LM2904AM8-13 operating characteristics with package guidance, application engineering notes, and a parameter-by-parameter comparison framework. It is intended to help engineers identify design constraints quickly while preserving the distinction between published device specifications and application-specific engineering judgments.

RFQ Contact
LM2904AN - Dual Op-Amp, 3-26V Single Supply | onsemi
LM2904AN

LM2904AN - Dual Op-Amp, 3-26V Single Supply | onsemi

The onsemi LM2904AN is a single-supply dual operational amplifier with two independent general-purpose amplifier circuits in an 8-pin PDIP (DIP-8) through-hole package, operating from a 3V to 26V supply range. According to the TI product family page, the LM2904 class delivers approximately 700 kHz of gain-bandwidth, and the onsemi version is characterized as a low-power dual op-amp with a common-mode input voltage range that extends to ground/VEE. A dual operational amplifier is an analog integrated circuit that houses two complete op-amp cores on a single silicon die, sharing one set of supply pins. In the voltage-regulator-to-amplifier hierarchy of signal-chain components, the op-amp sits between the passive components and the dedicated precision amplifier or instrumentation amplifier: it performs gain, buffering, filtering, and comparison functions that passive networks alone cannot achieve. Single-supply op-amps like the LM2904AN are designed so their input common-mode range includes the negative rail, simplifying circuits powered from a single positive rail such as 5V, 12V, or 24V industrial supplies. Key features of the LM2904AN include low power drain, single-supply or split-supply operation, input common-mode range extending down to the negative rail, and the industry-standard DIP-8 pinout shared across the LM358/LM2904 family. The wide 3V to 26V supply range covers 5V logic systems, 12V automotive rails, and 24V industrial buses without redesign. Technically, the two amplifiers are matched on a common substrate, ensuring closely tracking parameters over temperature. The output stage is designed for single-supply operation where the output can swing close to ground under light loads. Because the LM2904 is a low-cost, general-purpose part, designers should observe its class-B output behavior near the lower rail and its moderate slew rate when applying it to high-frequency or precision tasks. Typical applications include industrial sensor signal conditioning, transducer amplifier front ends, DC gain blocks, active filters, comparators with hysteresis, and low-frequency audio preamplifiers in through-hole prototypes and repair work where the PDIP package simplifies hand soldering and socketing. For design, provide adequate supply decoupling (100 nF ceramic close to pin 8 and pin 4) and avoid capacitive loads above roughly 100 pF without series isolation resistance to prevent oscillation. This page adds value beyond the manufacturer datasheet by combining distributor availability data, drop-in alternatives, a parametric comparison table, and practical design notes in one place.

RFQ Contact
LM2904ANG - Dual 8-PDIP General-Purpose Op Amp | onsemi
LM2904ANG

LM2904ANG - Dual 8-PDIP General-Purpose Op Amp | onsemi

The onsemi LM2904ANG is a dual, general-purpose operational amplifier packaged in an 8-pin plastic DIP. It provides two amplifier circuits per package, a 0.6 V/µs slew rate, and a 1 MHz gain-bandwidth product. The device supports single-supply or split-supply operation and has a common-mode input range that extends toward ground or VEE, making it suitable for conventional industrial and signal-conditioning circuits. An operational amplifier is a high-gain, low-output-impedance active device used to amplify voltage differences between two inputs. The LM2904 family belongs to the broader analog IC hierarchy of operational amplifiers, linear amplifiers, and analog signal-conditioning ICs. Its dual construction allows two independent amplifier channels in one package, reducing board area in designs that require multiple analog signal paths. The principal characteristics include two integrated circuits, a general-purpose amplifier architecture, a 0.6 V/µs slew rate, and a 1 MHz gain-bandwidth product. The common-mode input capability extending to ground or VEE is important for single-supply designs because it permits the amplifier to process input signals near the lower supply rail. Low power drain also makes the device suitable for battery-operated and low-power equipment when appropriately configured. The LM2904ANG is designed for general-purpose applications rather than precision or high-speed signal processing. Its 1 MHz gain-bandwidth product is adequate for audio, sensing interfaces, control loops, and low-frequency analog amplification. Because the device is listed as obsolete, engineers should also evaluate current-family alternatives when new production designs require an active lifecycle product. Typical uses include dual-stage sensor conditioning, low-frequency active filters, industrial control signal amplification, audio preamplification, and generic voltage-feedback stages. In each circuit, feedback components establish the closed-loop gain, while the supply rails and input common-mode range must remain within the operating conditions specified by the manufacturer. A practical design consideration is input bias-current compensation. The manufacturer documentation should be consulted for the recommended source impedance and compensation arrangement, particularly when driving low-impedance sources. PCB layout should keep feedback loops short and provide adequate ground-return paths to prevent additional noise or instability. This product page combines the LM2904ANG electrical characteristics, package information, lifecycle status, comparison data, and practical replacement guidance. It also identifies pin-compatible options for obsolete designs while helping engineers distinguish between a true board-level replacement and a merely similar amplifier.

RFQ Contact
LM2904AQM8-13 - Dual 36V Op Amp, 500uA | Diodes
LM2904AQM8-13

LM2904AQM8-13 - Dual 36V Op Amp, 500uA | Diodes

Diodes Incorporated LM2904AQM8-13 is an automotive-compliant, dual operational amplifier packaged in an 8-MSOP. The device operates from a 36 V maximum supply, provides two amplifier channels, and is specified for 500 uA supply current, 20 nA input bias current, and 100 dB open-loop gain. Its 8-MSOP package supports compact analog signal-conditioning layouts while retaining the industry-standard dual-op-amp pin arrangement described for the LM2904Q family. An operational amplifier, or op amp, is a high-gain analog amplifier used to amplify voltage differences, buffer sensors, drive external loads, and implement active filters. The LM2904 belongs to the broader general-purpose amplifier hierarchy, which includes dual and quad operational amplifiers used in signal-chain, instrumentation, and control applications. Its wide supply range makes it useful where signal levels and supply conditions vary substantially. The headline characteristics make the LM2904AQM8-13 appropriate for low-power signal conditioning. A 36 V maximum supply expands the usable operating envelope, while 500 uA supply current limits the power burden of dual-channel circuits. The 20 nA input bias current reduces loading on high-impedance sources, and 100 dB open-loop gain provides useful amplification when feedback establishes the closed-loop gain. The LM2904Q family uses industry-standard pin arrangements and is available in multiple small-outline packages. The M8-13 ordering option places this dual amplifier in an 8-MSOP. For conventional non-unity-gain operation, feedback networks define the closed-loop response, while input common-mode and output-swing limits must remain within the datasheet operating envelope. Decoupling should be placed close to the supply pins to reduce supply-borne noise. Typical uses include low-side current monitoring, transducer and sensor interfaces, buffered analog measurements, active filtering, and general-purpose signal conditioning in automotive or industrial equipment. The dual configuration reduces board area when two independent analog channels are required, although crossover distortion is important when similar signals are amplified simultaneously at high output levels. Designers should verify input bias current, input offset voltage, output swing, common-mode range, and stability requirements against the complete operating conditions. Avoid relying on rail-to-rail operation unless the applicable LM2904 datasheet explicitly confirms the required input or output range. Decoupling capacitors, grounding, and feedback-component placement remain important even though the amplifier itself has a low supply current of 500 uA. This product page consolidates the verified order information, package details, technical attributes, application guidance, and qualified drop-in comparison points. It is designed to help engineers determine whether the LM2904AQM8-13 fits a compact, dual-channel automotive signal-conditioning design and to identify the closest pin-compatible alternatives before a board-level substitution.

RFQ Contact
LM2904AQS-13 - Dual 36V Automotive Op Amp | Diodes
LM2904AQS-13

LM2904AQS-13 - Dual 36V Automotive Op Amp | Diodes

The Diodes Incorporated LM2904AQS-13 is a dual general-purpose operational amplifier in an 8-pin SO package, with a 2 V to 36 V supply span, 700 kHz gain-bandwidth product, and low input offset voltage. The LM2904AQS-13 is an automotive-compliant version of the LM2904A family, making it suitable for dual-amplifier signal-conditioning circuits operating from low-voltage industrial systems through 36 V automotive environments. Its operating-amplifier configuration provides two independent amplifiers in one package. An operational amplifier is a high-gain, differential-input analog amplifier used in the broader hierarchy of amplifier ICs, analog signal-chain ICs, and semiconductor devices. Its differential input allows a small voltage difference to be amplified relative to a feedback-defined reference. Common uses include voltage buffers, sensor amplification, active filters, comparators, and transducer-signal conditioning. The LM2904AQS-13 combines two amplifier channels in one SO-8 package, reducing board area compared with discrete single amplifiers. The device operates from 2 V to 36 V, tolerating a wide range of supply conditions. Its 700 kHz gain-bandwidth product supports general-purpose low-frequency signal amplification, while the listed 20 nA input bias current and 2 mV input offset voltage help define its suitability for moderate-accuracy sensing and feedback networks. The Diodes listing also identifies a 100 dB open-loop gain metric and approximately 500 uA supply-current class, which make the amplifier practical for low- and moderate-frequency industrial and automotive circuits. The LM2904AQ family is identified by Diodes Incorporated as automotive compliant. The S suffix in LM2904AQS-13 identifies the SO-8 package option, while -13 identifies the supplier packaging format. This dual-channel configuration allows one package to implement two independent amplifier stages, reducing component count when a board requires signal buffering, differential amplification, active filtering, or two sensing channels. Typical applications include 5 V and 12 V sensor interfaces, automotive transponder and battery-management signal conditioning, industrial process-control inputs, active low-pass filters, and general dual-amplifier boards. The wide 36 V supply capability is particularly useful where signal nodes can experience industrial transients or automotive battery-related voltages, provided the design keeps every pin within the device's absolute maximum ratings. Design the feedback network for the intended closed-loop bandwidth, keep input and output signals within the common-mode range, and bypass the supply pins close to the package. Decoupling capacitors should be placed at the IC rather than at the power-source entry point. If the amplifier drives capacitive loads, add an isolation resistor and verify stability and output-current margin in the final board layout. This page combines package, electrical, automotive-compliance, cross-reference, and replacement information with practical guidance for dual op-amp layouts. It helps engineers distinguish the exact automotive SO-8 device from broader LM2904 variants, package variants, and functional alternatives that may require different qualification or footprint review.

RFQ Contact
LM2904AQTH-13 - Dual 36V Automotive Op Amp | Diodes Incorporated
LM2904AQTH-13

LM2904AQTH-13 - Dual 36V Automotive Op Amp | Diodes Incorporated

The Diodes Incorporated LM2904AQTH-13 is a dual general-purpose operational amplifier with two independent amplifier channels, a 36 V supply rating, and an 8-pin TSSOP package. It is an automotive-compliant member of the LM2904AQ family and uses green mold compound as standard. An operational amplifier, commonly called an op amp, is an analog integrated circuit that compares an inverting input with a non-inverting input and drives its output toward the difference between them, amplified by a high open-loop gain. The LM2904AQ family contains independent dual amplifiers designed for general-purpose signal conditioning. Its two channels can process separate signals or be configured together for differential, filtering, comparator-style, and amplifier functions. The LM2904AQTH-13 combines two amplifier circuits in one compact package. Manufacturer listings identify a maximum supply voltage of 36 V, a supply current of 500 uA, an input bias current of 20 nA, and a 100 dB listed performance rating. These characteristics support low-power signal-chain designs operating from higher-voltage rails than typical 5 V or 3.3 V analog circuits, including industrial sensing, vehicle electronics, instrumentation, and low-level signal conditioning. The device belongs to the LM290xAQ automotive-compliant dual and quad operational-amplifier family. The LM2904Q and LM2904AQ dual versions are offered in SO-8, TSSOP-8, and MSOP-8 package options, while quad LM2902 devices use 14-pin packages. Industry-standard pinouts and green mold compound support compact surface-mount implementation and environmentally conscious manufacturing practices. Typical applications include automotive sensor interfaces, industrial transducers, battery-powered monitoring equipment, current sensing, signal amplification, and active filtering. The two independent channels allow one device to handle a differential measurement path or two related analog channels while reducing component count. Designers should still verify input common-mode range, output swing, stability, and absolute maximum ratings for the chosen operating conditions. For PCB design, place input, output, bypass, and compensation components close to their associated pins, then observe the pinout and layout guidance in the manufacturer datasheet. A clean grounding strategy and short feedback routes are especially important because long traces can introduce parasitic feedback, offset, and instability in high-gain amplifier configurations. This product page combines package, application, sourcing, and replacement guidance with practical design considerations. It is intended to help engineers identify the correct automotive dual op amp, verify the 8-pin TSSOP footprint, compare pin-compatible family options, and plan a stable surface-mount implementation without changing the PCB land pattern.

RFQ Contact
LM2904AS-13 - Dual Precision Op Amp | Diodes Inc.
LM2904AS-13

LM2904AS-13 - Dual Precision Op Amp | Diodes Inc.

Diodes Incorporated LM2904AS-13 is a dual operational amplifier with two amplifier channels, a 3 V to 36 V supply range, 1 mV input offset voltage, 100 dB open-loop gain, 1.1 MHz gain-bandwidth product, and 20 nA input bias current. The device is supplied in an 8-pin SO package and is characterized for operation from -40°C to +125°C. An operational amplifier is a high-gain analog signal-conditioning IC used to amplify voltage differences, buffer sensor outputs, implement active filters, and serve as the input stage of control and measurement systems. In the broader semiconductor hierarchy, the LM2904 belongs to the amplifier IC family, specifically low-power general-purpose operational amplifiers designed for single or dual supply operation. The two-channel configuration lets one package support independent signal paths while reducing board area and the number of required components. A 100 dB open-loop gain supports accurate amplification of small signals, while the 1.1 MHz gain-bandwidth product provides useful bandwidth for common low-frequency and moderate-frequency analog tasks. The stated 20 nA input bias current is particularly relevant when the source impedance is high. The 3 V to 36 V supply span permits operation from conventional single-supply rails through higher industrial supply voltages. Its specified 1 mV input offset supports applications where input-referred error must be controlled relative to the signal level. The -40°C to +125°C characterization provides a broad temperature range for industrial equipment, instrumentation, automotive-adjacent circuitry, and other systems requiring stable operation over extended environmental conditions. Typical uses include transducer-signal conditioning, active audio and control paths, low-frequency filter stages, sensor amplification, and general dual-amplifier circuits. The SO-8 package is suitable for conventional surface-mount assembly, and the manufacturer states that the LM2904/LM2902 family uses green mold compound as standard. When laying out a circuit, keep input and feedback paths short, provide stable bypassing close to the supply pins, and confirm common-mode and output-swing limits at the selected supply voltage and load. Decoupling capacitors should be placed using standard op-amp layout practice to minimize parasitic feedback and unstable operation. This product page combines the manufacturer specification summary, distributor identification, lifecycle-relevant sourcing information, and practical application guidance. It also documents the verified limits of the available drop-in comparison set so engineers can distinguish confirmed same-footprint choices from related LM2904-family devices that require package or qualification review.

RFQ Contact
LM2904ATH-13 - Dual General-Purpose Op Amp | Diodes Incorporated
LM2904ATH-13

LM2904ATH-13 - Dual General-Purpose Op Amp | Diodes Incorporated

The Diodes Incorporated LM2904ATH-13 is a dual, general-purpose operational amplifier packaged in an 8-pin TSSOP. It is intended for single-supply or dual-supply signal-conditioning applications and uses the widely recognized LM2904 amplifier architecture. The device operates from a single supply up to 36 V or from split supplies totaling 36 V, equivalent to ±18 V, while providing two amplifiers in one package. The LM2904 family is intended for general-purpose amplifier, comparator, and voltage-control applications where economy, wide supply-voltage operation, and straightforward PCB implementation are important. An operational amplifier is an analog building block that amplifies the difference between two input voltages. Within the broader semiconductor hierarchy, this product is a general-purpose operational amplifier, or op amp, used in analog signal chains, feedback-control loops, sensor interfaces, and buffer stages. The dual configuration allows one IC to implement two independent amplifier channels, reducing board area and simplifying designs that compare, amplify, filter, or condition two signals. The LM2904ATH-13 provides two independent channels with high open-loop gain and approximately 700 kHz gain-bandwidth performance. Its general-purpose positioning makes it suitable for audio preamplification, transducer conditioning, DC signal amplification, and low-to-moderate-frequency control applications. The 8-pin TSSOP package supports compact surface-mount layouts, while the tape-and-reel suffix identifies the production packing format. Exact input-offset, input-bias-current, output-swing, noise, and temperature limits must be confirmed against the manufacturer datasheet for the exact ordering code. The architecture is suited to conventional single-supply operation because the device can operate close to the positive rail while its output approaches the negative rail. Input common-mode range, output swing, slew rate, and stability conditions still determine whether a particular gain, load, and bypass-capacitor arrangement will meet the design objective. Decoupling should be placed close to the supply pins, and feedback components should be kept compact to minimize parasitic coupling and instability risk. Typical uses include low-level audio stages, current-to-voltage conversion for sensor outputs, general comparator configurations, small-signal amplification, and feedback control around slower feedback loops. The two independent channels can also be configured as comparators, buffers, amplifiers, or differential amplifier sections where their internal characteristics permit the intended operation. Applications requiring very low offset, low noise, high speed, low power, or rail-to-rail output should not assume that a general-purpose LM2904 is the optimal choice. For a robust design, begin with the manufacturer pin configuration and confirm the absolute-maximum ratings, common-mode limits, output-current capability, and recommended external-component values. Avoid using component-marking variants as substitutes without checking the exact pinout, supply range, temperature grade, and package. The TSSOP footprint also requires careful lead pitch and solder-joint inspection because its closely spaced leads are more difficult to inspect than wide-lead SOIC packages. This product page combines the LM2904ATH-13 ordering information, a pin-compatible replacement framework, and practical analog-layout guidance. It highlights the critical decisions engineers must make when reusing an existing 8-pin TSSOP footprint while preserving supply-voltage, common-mode, output-swing, temperature, and load-current requirements.

RFQ Contact
LM2904AVQDRG4 - Dual 36V 1MHz Op Amp | Texas Instruments
LM2904AVQDRG4

LM2904AVQDRG4 - Dual 36V 1MHz Op Amp | Texas Instruments

Texas Instruments LM2904AVQDRG4 is a dual, general-purpose operational amplifier with two independent channels, a 1 MHz gain-bandwidth product, and operation from a single supply up to 26 V or split supplies up to 36 V total. The device is packaged in an 8-SOIC package and is supplied on tape and reel. An operational amplifier, or op amp, is a high-gain analog signal-conditioning component that compares its inverting and non-inverting inputs and drives its output toward the difference between them. The LM2904 belongs to the broader hierarchy of dual operational amplifiers, analog amplifiers, integrated circuits, and general-purpose analog signal-processing devices. Its two channels share power pins but otherwise operate independently, allowing one package to provide amplification, buffering, filtering, or comparison functions. The principal benefits are a 1 MHz gain-bandwidth product, a 0.3 V/µs slew rate, and low supply-current drain of approximately 0.7 mA per amplifier. Each amplifier includes frequency compensation and is designed for operation from single or split supplies. The input common-mode range includes ground, which supports common single-supply signal-conditioning arrangements. The automotive-qualified ordering option is identified by the Q designation in the part number, although qualification documentation should be checked for the specific production configuration. The internal architecture is designed for dependable general-purpose operation with a useful combination of gain, bandwidth, input range, and supply flexibility. A typical noninverting amplifier gain of 100 has a closed-loop bandwidth of approximately 10 kHz, while a unity-gain configuration supports signal bandwidth up to the device's stated 1 MHz gain-bandwidth product. These figures make the amplifier suitable for slow sensor signals, audio-frequency circuits, feedback-control loops, and general analog conditioning rather than high-speed data acquisition. Typical applications include industrial sensor interfaces, automotive signal-conditioning modules, low-frequency active filters, audio preamplifier stages, current sensing with resistive shunts, and dual-rail buffer circuits. Two independent channels can process complementary signals or perform separate functions, reducing component count and conserving board area compared with two single amplifiers. When designing the circuit, check input and output common-mode limits at the actual supply voltage. Load output signals through appropriate biasing, use a stable reference for precision offset-sensitive measurements, and avoid operating the amplifier near supply-rail limits without confirming the input and output ranges. Place decoupling capacitors close to the power pins and keep feedback traces short to reduce oscillation and noise pickup. This page consolidates the device identity, ordering information, package details, pin assignment, engineering alternatives, and practical design guidance needed to evaluate the LM2904AVQDRG4 for a new analog circuit.

RFQ Contact
LM2904AVQDRG4Q1 - 26V Dual 700kHz Op Amp | Texas Instruments
LM2904AVQDRG4Q1

LM2904AVQDRG4Q1 - 26V Dual 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904AVQDRG4Q1 is an automotive-grade, dual general-purpose operational amplifier with a 26 V supply rating, 700 kHz gain-bandwidth product, and 0.3 V/µs slew rate, housed in an 8-SOIC package. It combines two independent amplifiers with internal frequency compensation and is qualified to AEC-Q100 specifications for automotive applications. An operational amplifier is a high-gain, differential-input analog amplifier that uses external feedback to set its closed-loop gain and signal behavior. Within the broader semiconductor hierarchy, this device belongs to the linear-amplifier family and ultimately to the amplifier-IC category. The LM2904 family is widely used for low-frequency signal conditioning because it combines reasonably high open-loop gain, broad supply-voltage capability, low supply-current consumption, and a conventional industry-standard pin arrangement. The most prominent operating characteristics are its 26 V maximum supply rating, 700 kHz gain-bandwidth product, and 0.3 V/µs slew rate. Each channel supports single-supply operation, while the two amplifiers can also be used with suitable bipolar supplies. The device is intended for general-purpose amplification and includes two circuits in one 8-SOIC package, reducing board area compared with separate single amplifiers. Its frequency-compensated architecture is suited to non-inverting, inverting, summing, comparator-like, and transducer-amplification stages operating within the device's bandwidth. The automotive qualification is important where operating-temperature robustness and controlled quality are required. Exact input-offset voltage, input-bias current, output-current capability, common-mode limits, and temperature limits must be confirmed in the manufacturer datasheet for the selected grade and package. Typical uses include low-level sensor conditioning, transducer amplifiers, DC gain stages, active filters, audio and communications interfaces, and automotive signal-processing modules. The two-amplifier configuration is particularly useful when a board needs two similar signal paths in one package, such as differential sensing or paired filter stages. Design with the 700 kHz bandwidth and 0.3 V/µs slew rate in mind. Keep input and feedback routing short, observe the supply and common-mode limits from the manufacturer datasheet, and verify output swing at the intended load. Decoupling capacitors should be placed close to the supply pins to reduce supply impedance and switching noise. This product page combines the exact ordering information, package details, qualified family information, verified drop-in candidates, and practical design considerations needed to plan an automotive dual-op-amp design before committing the LM2904AVQDRG4Q1 to a PCB.

RFQ Contact
LM2904AVQDRQ1 - 26V 700kHz Dual Op Amp | Texas Instruments
LM2904AVQDRQ1

LM2904AVQDRQ1 - 26V 700kHz Dual Op Amp | Texas Instruments

The Texas Instruments LM2904AVQDRQ1 is an automotive-grade, dual operational amplifier rated for 26 V supply operation and 700 kHz gain-bandwidth performance, housed in an 8-pin SOIC package. The device contains two independent, general-purpose amplifiers with frequency compensation, making it suitable for signal conditioning, sensor amplification, and automotive electronic control systems. An operational amplifier, commonly abbreviated op amp, is an analog signal-processing IC that compares an input voltage with a feedback reference and drives its output to reduce the difference between them. A dual operational amplifier combines two amplifiers in one package, reducing board area and simplifying dual-channel or differential signal-chain designs. The LM2904-Q1 family extends the widely recognized LM2904 architecture with automotive qualification under AEC-Q100 requirements. The LM2904AVQDRQ1 provides a 26 V maximum supply rating, a 700 kHz gain-bandwidth product, and an operating temperature range of -40°C to +125°C. Its low-supply-current design supports power-constrained systems, while the high-voltage capability accommodates automotive and industrial transients when paired with appropriate protection. The device also includes ESD protection exceeding 500 V under MIL-STD-883, Method 3015 and exceeding 200 V using the machine model. Internally, the LM2904 family uses two independent, high-gain, frequency-compensated operational-amplifier channels. Internal compensation removes the need for an external frequency-compensation network in typical closed-loop gain configurations. This characteristic simplifies PCB design and supports common amplifier arrangements such as voltage followers, non-inverting gain stages, inverting amplifiers, comparators, and transducers with differential outputs. Typical applications include automotive sensor interfaces, low-side current measurement, pressure and temperature conditioning, battery monitoring, audio preamplification, and general-purpose control modules. Its dual-channel organization is particularly useful when a design needs one amplifier for signal conditioning and another for filtering, buffering, or an independent control function. Designers should verify the input common-mode range and output-swing limits against the actual supply voltage and signal range. The datasheet pin configuration should be used directly during PCB routing, particularly because the dual amplifier shares common supply pins. Input and output paths should also be kept away from switching-current loops to minimize coupled noise. This page combines manufacturer qualification details, a focused replacement comparison, and practical circuit-level guidance for engineers evaluating the LM2904AVQDRQ1 in automotive and industrial analog signal chains. The product is an operational amplifier, a linear amplifier, an analog IC, and a semiconductor device designed for voltage feedback and signal-conditioning applications.

RFQ Contact
LM2904AVQPWR - Dual 30V 700kHz Op Amp | Texas Instruments
LM2904AVQPWR

LM2904AVQPWR - Dual 30V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904AVQPWR is a dual, general-purpose operational amplifier in an 8-pin TSSOP package, with two independent, internally frequency-compensated amplifiers. The device supports a 30 V maximum total supply rating, delivers a typical gain-bandwidth product of 700 kHz, and operates across a -40°C to 125°C temperature range. Its two-amplifier configuration makes it suitable for signal conditioning, transducer amplification, and analog control circuits using single or split supplies. An operational amplifier is an analog building block that amplifies the voltage difference between its differential input while using negative feedback to set closed-loop gain and bandwidth. The LM2904 belongs to the broader hierarchy of linear amplifiers, analog signal-chain ICs, and semiconductor components. It is internally compensated, which simplifies implementation by removing the need for an external compensation capacitor in standard closed-loop configurations. Key characteristics include low supply-current drain, low input bias and offset currents, and an input common-mode range that extends close to ground for single-supply applications. The typical supply-current consumption is 0.7 mA per amplifier. Its broad supply range and temperature rating support industrial control, automotive, instrumentation, and test-equipment designs where the amplifier must operate across changing supply and ambient conditions. The LM2904 architecture uses two independent, high-gain, frequency-compensated amplifiers in one package. Internal compensation establishes the dominant pole and makes unity-gain operation practical without external compensation components. The 700 kHz gain-bandwidth product supports moderate-frequency signal conditioning rather than high-speed data acquisition, so layout should minimize feedback-loop area and keep sensitive input nodes away from supply and output routing. Typical uses include sensor-amplifier front ends, low-frequency active filters, comparator-style threshold circuits with saturation recovery, audio preamplifier stages, and programmable control interfaces. For automotive and industrial systems, the wide operating-temperature range and wide supply tolerance are especially useful, while the low input bias current helps preserve sensor accuracy. When designing around the LM2904AVQPWR, verify the input common-mode range against the actual signal and supply levels, particularly near the positive rail. Decoupling capacitors should be placed directly across the supply pins, and unused amplifier inputs must be biased rather than left floating. Avoid relying on the device for millivolt-level precision tasks without checking offset, drift, and bias-current contributions for the complete signal chain. This page consolidates package details, verified distributor pricing evidence, drop-in alternatives, and application-oriented design guidance for engineers evaluating the LM2904AVQPWR. It also distinguishes supply-voltage, temperature, channel-count, and bandwidth trade-offs among pin-compatible LM2904-family options.

RFQ Contact
LM2904AVQPWRG4 - Dual 700kHz Op Amp | Texas Instruments
LM2904AVQPWRG4

LM2904AVQPWRG4 - Dual 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904AVQPWRG4 is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, 26 V maximum total supply capability, and an 8-pin TSSOP package. Each amplifier channel provides input, output, and supply connections, allowing one package to implement two independent gain stages or a differential amplifier arrangement. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The LM2904 belongs to the operational-amplifier hierarchy, where it serves as a general-purpose amplifier for signal conditioning, buffering, voltage amplification, and feedback-based control. Its common-mode input range includes ground, allowing direct sensing of signals near 0 V. The device operates from single or dual supplies. The manufacturer specifies operation from up to 26 V total for single-supply operation, or up to 13 V per rail for dual supplies. A typical supply-current drain of 0.7 mA is specified as independent of supply voltage. The two-amplifier configuration also supports independent operation of each channel rather than requiring both channels to perform the same function. The 700 kHz gain-bandwidth product supports general-purpose amplification at low and moderate frequencies rather than high-speed signal conditioning. Because this is not a rail-to-rail input or output device, the input and output operating regions must remain within the amplifier’s supply-dependent limits. Bias and offset requirements should be checked against the circuit’s signal amplitude and source impedance. Typical applications include low-frequency sensor conditioning, analog signal buffering, feedback control, audio preamplification, and general instrumentation. The TSSOP package supports compact surface-mount layouts, while the dual channel count reduces component count when two gain stages are needed. In a single-supply system, the input common-mode range extending to ground is especially useful for signals produced by sensors near the lower supply rail. When laying out the circuit, keep feedback components and input sources close to the appropriate pins, maintain a common ground reference, and decouple the supply connection. Avoid relying on the amplifier for isolation or level translation outside its specified input and output ranges. Stability with capacitive loads should be evaluated because capacitive loading can alter the effective gain-bandwidth response and introduce peaking. This product page combines the manufacturer’s electrical characteristics with package, sourcing, replacement, and application guidance. It also identifies the differences between verified same-brand family alternatives and highlights the electrical checks required before treating any substitute as a true drop-in replacement.

RFQ Contact
LM2904AVQPWRG4Q1 - Dual 26V 700kHz AEC-Q100 Op Amp | TI
LM2904AVQPWRG4Q1

LM2904AVQPWRG4Q1 - Dual 26V 700kHz AEC-Q100 Op Amp | TI

The Texas Instruments LM2904AVQPWRG4Q1 is a dual, general-purpose operational amplifier with a 26 V maximum supply rating, 700 kHz gain-bandwidth product, and AEC-Q100 automotive qualification. The device is offered in an 8-pin TSSOP package and supports single-supply or dual-supply operation, making it suitable for automotive, industrial, and low-cost analog signal-conditioning circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The dual configuration provides two independent amplifiers in one package, which saves board area in applications such as sensing, filtering, buffering, and control loops. Within the device hierarchy, this part belongs to the operational amplifier family of amplifier ICs, combining wide supply-voltage tolerance with low supply-current consumption. Key characteristics include a 700 kHz gain-bandwidth product, an input common-mode range that includes ground, and a low typical supply-current drain of 0.7 mA. The common-mode capability supports direct sensing near ground in battery-powered and sensor-interface circuits. Single-supply operation is possible because the common-mode input range reaches the negative supply rail, while the 26 V rating supports higher-voltage industrial control systems. The LM2904 architecture uses frequency compensation to provide stable closed-loop operation in typical amplifier configurations. Its wide supply range and low supply-current drain suit applications that need adequate signal headroom without continuous high quiescent power. Automotive qualification is provided under AEC-Q100 specifications for the LM2904-Q1 family. Typical uses include 12 V automotive sensor conditioning, low-side current measurement, transducer amplification, active filtering, and general-purpose analog control. The TSSOP-8 outline also supports compact mixed-signal boards where a dual amplifier is needed rather than two separate single-channel devices. Design with adequate supply decoupling, confirm the input common-mode and output-swing limits against the actual signal range, and check the maximum total supply voltage before applying power. This page also organizes pinout, packaging, qualification, drop-in alternatives, and application guidance for faster component selection.

RFQ Contact
LM2904AVQPWRQ1 - 26V, 700kHz Automotive Dual Op Amp | TI
LM2904AVQPWRQ1

LM2904AVQPWRQ1 - 26V, 700kHz Automotive Dual Op Amp | TI

Texas Instruments LM2904AVQPWRQ1 is an automotive-grade, dual operational amplifier with a 26 V maximum supply rating, 700 kHz gain-bandwidth product, and an 8-pin TSSOP (PW) package. The device contains two independent, high-gain, frequency-compensated amplifiers and is qualified to AEC-Q100 specifications for automotive applications. An operational amplifier is an analog IC that provides high open-loop gain and signal amplification for sensors, control loops, filters, and signal-conditioning circuits. The LM2904-Q1 family belongs to the operational amplifier hierarchy, where each amplifier section provides voltage amplification, impedance buffering, and feedback-based signal conditioning within a wider analog or mixed-signal system. Key characteristics include two amplifier circuits, a 700 kHz gain-bandwidth product, a 0.3 V/µs slew rate, a typical input offset voltage of 3 mV, and typical input bias current of 20 nA. The operating temperature range extends from -40°C to +125°C, supporting industrial and automotive environments where temperature and qualification requirements exceed those of ordinary general-purpose amplifiers. The internally compensated architecture simplifies implementation of standard inverting, non-inverting, summing, and feedback amplifier circuits. A typical supply current is 500 µA per channel, while output current capability reaches 40 mA per channel. These characteristics make the device suitable for low-power analog signal conditioning where a 3 V minimum supply is required and the circuit must tolerate supply voltages up to 26 V. Typical uses include sensor interfaces, actuator drivers, motor-control feedback networks, battery-powered instrumentation, industrial control loops, and automotive signal-conditioning modules. The wide supply range allows operation from single or split supplies, although the differential voltage between the supply rails must remain within the device limits. Designers should verify output swing, input common-mode range, stability, and load capability across the complete supply and temperature range. Decoupling capacitors should be placed close to the supply pins, while feedback components and sensitive input routes should be kept away from switching nodes to reduce coupling and maintain low offset performance.

RFQ Contact
LM2904AWYPT - Dual Low-Power Op Amp, 8-TSSOP | STMicroelectronics
LM2904AWYPT

LM2904AWYPT - Dual Low-Power Op Amp, 8-TSSOP | STMicroelectronics

The STMicroelectronics LM2904AWYPT is a low-power dual operational amplifier with two independent, internally frequency-compensated amplifiers in an 8-pin TSSOP package. The device is identified for ±15 V / 30 V automotive applications and is associated with AEC-Q100 qualification in distributor listings. Its dual-amplifier configuration makes it suitable for signal conditioning, voltage buffering, instrumentation, and general-purpose analog circuits where two amplifier channels are required in one compact package. An operational amplifier is a voltage-controlled, high-gain analog building block used to amplify, buffer, filter, or compare small electrical signals. The LM2904 belongs to the dual general-purpose operational-amplifier family, combining two amplifier sections with internal frequency compensation in a single surface-mount IC. This type of device sits within the broader analog IC and semiconductor hierarchy and is commonly used between sensors, transducers, reference circuits, and downstream measurement or control stages. Key features include two amplifier circuits in one package, low-power operation, internal frequency compensation, and an 8-pin TSSOP surface-mount form factor. The automotive identification is useful when the application requires an AEC-Q100-qualified device, although the exact temperature range, supply limits, input and output characteristics, slew rate, and common-mode performance should be confirmed against the STMicroelectronics datasheet for the exact order code. The package also supports compact PCB layouts where two amplifier channels must be placed close together. The internal compensation allows the amplifier sections to operate without external frequency-compensation components in typical closed-loop configurations. That simplifies analog design and reduces the number of external components in feedback networks. Because the product is a dual amplifier, both channels have their own inputs and outputs, enabling common tasks such as differential sensing, active filtering, or complementary signal processing within one package. The manufacturer product page describes the device as two independent, high-gain operational amplifiers with internally implemented frequency compensation. Typical applications include automotive sensor interfaces, industrial control modules, low-power signal-conditioning boards, battery-powered instruments, audio preamplifier stages, and general-purpose analog front ends. In an instrumentation application, one channel could amplify a sensor signal while the other handles buffering or an active-filter function. In a vehicle electronics module, the dual amplifier can reduce the number of discrete analog ICs while supporting a compact, surface-mount assembly. The principal design consideration is to verify the exact electrical limits and recommended operating conditions before finalizing the power rails, input common-mode range, output swing, and external feedback network. Decoupling capacitors should be placed close to the supply pins, and the PCB layout should minimize parasitic capacitance and resistance on feedback and input nodes. The TSSOP package is small, so adequate copper and solder-joint quality remain important for reliable assembly. This page combines manufacturer identification, distributor listings, cross-reference information, drop-in alternatives, and engineering-oriented design guidance for engineers evaluating LM2904AWYPT. It focuses on the distinctions that affect PCB compatibility, supply planning, signal conditioning, and automotive qualification rather than repeating only the basic catalog description.

RFQ Contact
LM2904AYDT - Dual 1.1MHz Op Amp | STMicroelectronics
LM2904AYDT

LM2904AYDT - Dual 1.1MHz Op Amp | STMicroelectronics

The STMicroelectronics LM2904AYDT is a dual general-purpose operational amplifier with two independent, internally frequency-compensated amplifiers, a 1.1 MHz gain-bandwidth product, 0.6 V/us slew rate, and 20 nA input bias current. The device operates from a single positive supply and is packaged in an 8-pin SOIC for automotive and industrial control systems. An operational amplifier is an analog signal-conditioning device that compares an inverting input with a non-inverting input and amplifies the voltage difference between them. The dual-amplifier configuration places two independent amplifiers in one package, allowing one IC to implement two signal paths. Within the broader semiconductor hierarchy, an operational amplifier belongs to the linear amplifier family and supports closed-loop gain, filtering, buffering, current-to-voltage conversion, and feedback-control applications. The LM2904AYDT provides two independent channels, 1.1 MHz gain-bandwidth product, 0.6 V/us slew rate, and 20 nA input bias current. Its internally compensated architecture simplifies typical closed-loop amplifier use without an external frequency-compensation network. The low input bias current is useful when the amplifier must operate with relatively high source impedance, while the 1.1 MHz bandwidth supports general-purpose signal amplification at low and moderate frequencies. The circuit is designed specifically for automotive and industrial control systems and operates from a single power supply over a wide voltage range. Both channels are independent, so they can process separate signals and do not share internal signal paths. The SOIC-8 package offers a compact surface-mount format compatible with conventional PCB assembly, while the automotive-oriented ordering code identifies the manufacturer’s grade and delivery configuration. Typical uses include low-frequency sensor conditioning, industrial control-loop amplifiers, transducers with relatively high source impedance, buffer stages, and general signal-conditioning modules. Two channels can be used for a differential stage, a voltage follower and an active filter, or two independent control channels. The device is best suited to general-purpose precision amplification rather than high-speed, high-voltage, or low-noise applications requiring specialized amplifier families. When laying out a PCB, keep input and feedback traces short, route them away from switching nodes, and provide a stable ground reference. Decouple each supply rail close to the device with suitable ceramic capacitance and avoid placing long output traces beside high-current digital paths. Because the SOIC-8 leads are closely spaced, inspect assembly clearances and ensure adequate copper and soldermask isolation under the package. This page combines the manufacturer’s functional description with package, qualification, lifecycle, sourcing, and cross-reference information. It also provides application-focused engineering guidance and a parameter comparison table so engineers can evaluate the LM2904AYDT against other compatible SOIC-8 dual operational amplifiers before committing a design.

RFQ Contact
LM2904AYPT - Dual Low-Power Op-Amp, 1.1MHz | STMicroelectronics
LM2904AYPT

LM2904AYPT - Dual Low-Power Op-Amp, 1.1MHz | STMicroelectronics

The STMicroelectronics LM2904AYPT is a low-power dual operational amplifier with two independent general-purpose amplifier circuits, a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, and operation from a single supply of 3 V to 30 V, housed in an 8-pin TSSOP package. The A suffix and Y suffix identify the automotive-grade version, which STMicroelectronics qualifies for harsh automotive and industrial environments with extended temperature capability. An operational amplifier (op-amp) is an analog building block that amplifies the voltage difference between its two inputs with very high open-loop gain. As a member of the operational amplifier hierarchy, the LM2904 family sits under linear amplifiers, then amplifier ICs, then analog integrated circuits. Dual op-amps such as the LM2904A integrate two matched amplifiers in one package, saving board area and improving channel matching in multi-stage analog signal chains. Key features include an input offset voltage of typically 2 mV (maximum 7 mV per the LM2904A grade), an input bias current of 20 nA, a large common-mode input range that extends to the negative rail, and single-supply operation down to 3 V. A power drain of only 0.7 mA per amplifier (typical) makes the part suitable for battery-powered and always-on circuits. Output current capability of approximately 20 mA per channel drives moderate loads directly. The bipolar process technology used in the LM2904A provides rugged, well-understood behavior: graceful performance degradation near the rails, low 1/f-noise characteristics typical of bipolar input stages, and a unity-gain stable configuration requiring no external compensation capacitor. The internal 100 dB-class DC open-loop gain and good channel-to-channel matching support precision comparator, amplifier, and filter topologies. Typical applications include automotive sensor signal conditioning (oxygen sensors, position sensors), battery monitors and current-sense amplifiers in 12 V and 24 V vehicle systems, industrial transducer front ends, active filters, comparators with hysteresis, and low-speed signal buffering in HVAC and appliance controllers. When designing with the LM2904AYPT, remember that the output cannot swing fully to the positive rail and that phase reversal is avoided on the inverting input only within the specified common-mode range; keep gain-setting resistors above 10 kohm to limit bias-current error, and place a 100 nF decoupling capacitor within 5 mm of pin 8. This page adds value beyond the manufacturer datasheet by combining drop-in alternative comparisons, application-specific design notes, parametric comparison tables, and sourcing guidance in one place.

RFQ Contact