Products (44,000+)

LT1114IN - 4-Channel Precision Op Amp | Analog Devices
LT1114IN

LT1114IN - 4-Channel Precision Op Amp | Analog Devices

Analog Devices LT1114IN is a four-channel, general-purpose precision operational amplifier designed for low-power signal conditioning and instrumentation applications. The device provides a 750 kHz gain-bandwidth product, 0.3 V/µs slew rate, picoamp-class input bias characteristics, and an industrial-grade temperature range. It is packaged in a 14-pin DIP through-hole package. An operational amplifier is an active analog circuit element used to amplify voltage differences between its differential inputs. The LT1114IN belongs to the precision amplifier hierarchy: precision op amp, operational amplifier, analog signal-conditioning IC, and power-management semiconductor. Its four channels allow compact implementations of filtering, buffering, instrumentation, and active gain stages without requiring four separate single-channel packages. The key performance characteristics include a 750 kHz gain-bandwidth product, 0.3 V/µs slew rate, 60 µV maximum offset voltage for prime grades, 0.5 µV/°C maximum input-bias drift, and low-power operation. These specifications make the LT1114IN suitable for transducers, sensor interfaces, analog measurement systems, and general-purpose signal paths where offset stability and low input current are important. The LT1114IN uses a bipolar precision operational-amplifier architecture. The 14-DIP (0.300 inch, 7.62 mm) package provides through-hole lead spacing for conventional PCB assembly, prototypes, and repair work. Because each amplifier has its own differential input and output pins, the package supports four independent analog channels while retaining a straightforward DIP footprint. Typical uses include low-frequency instrumentation, current-loop and voltage-signal conditioning, buffered sensor interfaces, active filters, sample-and-hold stages, and industrial control modules. The 750 kHz bandwidth is suitable for moderate-speed signal conditioning rather than high-frequency video or RF amplification. Designers should verify supply voltage, output swing, input common-mode range, noise, and stability requirements against the manufacturer datasheet for the exact grade. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer’s recommended practice rather than left floating. This product page combines the official Analog Devices product information, package and performance details, sourcing guidance, drop-in alternatives, and practical design notes. It helps engineers compare the LT1114IN with pin-compatible options while planning temperature-grade, package, and lifecycle requirements.

RFQ Contact
LT1114IS - 4-Channel 750kHz Precision Op Amp | Analog Devices
LT1114IS

LT1114IS - 4-Channel 750kHz Precision Op Amp | Analog Devices

Analog Devices LT1114IS is a four-channel precision operational amplifier with a 750 kHz gain-bandwidth product, 0.3 V/µs slew rate, and picoamp-class input bias characteristics. The device is packaged in a narrow 16-pin SOIC and is intended for general-purpose precision signal conditioning where four amplifiers must fit on a compact PCB footprint. An operational amplifier, or op amp, is a differential voltage-controlled amplifier with high input impedance and open-loop gain. Its feedback network determines the completed function, allowing one device to perform inverting, non-inverting, summing, filtering, buffering, and gain-control operations. The LT1114 belongs to the operational amplifier hierarchy within analog ICs, combining four precision amplifier channels into one package for instrumentation, sensor, industrial-control, and low-frequency analog systems. The LT1114 family emphasizes low power, precision, and picoamp input bias current. Its 750 kHz gain-bandwidth product is suitable for moderate-frequency closed-loop amplification, while the 0.3 V/µs slew rate provides adequate response for common low-speed control and measurement signals. The prime-grade maximum offset voltage is 60 µV, supporting accurate DC operation when resistor matching and bias-current compensation are also managed carefully. The four amplifier channels share a common package but provide independent signal paths. This arrangement reduces component count and simplifies routing in designs requiring several matched functional stages, such as instrumentation amplifiers, active filters, motor-control loops, and sensor-conditioning circuits. The narrow SOIC-16 footprint is considerably smaller than a wide-body competitor package, helping conserve board area without requiring a specialized land pattern. Typical applications include low-level sensor amplification, current-loop measurement, buffer stages for analog-to-digital converters, active filtering, process-control signals, and general instrumentation. Because the gain-bandwidth product is 750 kHz, the device is best matched to low- and moderate-bandwidth signals rather than high-speed waveform, video, or RF chains. Design with the input common-mode range, output swing, supply voltage, noise, and stability requirements in mind. Place each decoupling capacitor close to its supply pins, avoid long high-impedance input traces where possible, and check the recommended feedback-network values in the manufacturer datasheet. The LT1114IS is supplied in tube packaging for the identified ordering configuration. This product record combines the manufacturer family description, ordering information, package details, and verified distributor metadata with practical guidance on amplifier selection, signal conditioning, and drop-in replacement evaluation.

RFQ Contact
LT1114S - Quad Low Power Precision Op Amp | Analog Devices
LT1114S

LT1114S - Quad Low Power Precision Op Amp | Analog Devices

The Analog Devices LT1114S is a quad low-power precision operational amplifier that combines picoampere-level input bias current with low offset voltage in a 16-pin SOIC package. The device delivers a 750 kHz gain-bandwidth product and a 0.27 V/µs slew rate while drawing minimal quiescent current per amplifier, suiting it to battery-powered precision signal chains. A precision op amp is a linear integrated circuit that amplifies low-level analog signals with high accuracy, characterized by low input offset voltage, low input bias current, low noise, and high open-loop gain. The LT1114S belongs to the operational amplifier family within the amplifier IC hierarchy, which falls under the broader category of analog signal conditioning ICs in mixed-signal semiconductor design. Quad packages integrate four independent op amps for channel-dense applications such as multi-sensor signal conditioning, instrumentation front-ends, and active filter banks. The LT1114S achieves 60 µV maximum offset voltage on the prime grade and 75 µV on the low-cost grade, with picoampere input bias current and low supply current per amplifier. It operates from ±1 V to ±20 V supplies, has a 750 kHz gain-bandwidth product, and 0.27 V/µs slew rate. The device includes industry-standard pinout in the SOIC-16 (S16) package, enabling direct drop-in upgrades of legacy quad precision op amps such as the OP-400, OP-497, and AD704. The LT1114S uses a bipolar input stage with bias-current cancellation that delivers picoampere input bias current without the noise penalty of CMOS JFET inputs. Its trimmed input stage and on-chip temperature compensation keep offset voltage low across the -40 °C to +85 °C industrial temperature range, supporting precision measurement systems that must hold calibration over thermal cycling. Typical applications include precision instrumentation amplifiers, strain-gauge and thermocouple signal conditioning, multi-channel data-acquisition front-ends, medical instrumentation, and active analog filters. The wide supply range also supports ±15 V industrial systems. When designing with the LT1114S, choose the prime grade when offset voltage and drift directly impact system accuracy; choose the low-cost grade when budget dominates and 75 µV offset is acceptable. The LT1114S is pin-compatible with the OP-400, OP-497, and AD704 quads, allowing board-level upgrades with no PCB rework. This page synthesizes distributor pricing, drop-in upgrade alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select and source the LT1114S for precision analog designs.

RFQ Contact
LT111A - 250ns Voltage Comparator | Analog Devices
LT111A

LT111A - 250ns Voltage Comparator | Analog Devices

The Analog Devices LT111A is a general-purpose voltage comparator with 1.0 mV maximum input offset voltage, 5.0 nA maximum input offset current, and a maximum response time of 250 ns. It operates from a single 5 V supply through ±15 V supplies and is available in the verified TO-5 package. A voltage comparator is an integrated circuit that determines whether an input voltage is above or below a reference level, producing a logic output suitable for control, monitoring, or switching decisions. The LT111A belongs to the comparator family within analog integrated circuits and power-management control systems. Unlike an operational amplifier intended primarily for linear amplification, the comparator is optimized for fast, saturated output transitions and threshold decisions. The LT111A improves on the LM111 general-purpose comparator according to the manufacturer datasheet. Its headline specifications include 1.0 mV maximum input offset voltage, 5.0 nA maximum input offset current, and 250 ns maximum response time. The input stage accepts differential input signals up to ±30 V, while the output can drive loads up to 50 mA referenced to ground or either supply, as stated in the datasheet search data. The component includes offset balancing and strobe capability. A separate output ground pin allows the output reference to be selected independently of the circuit ground, which is useful when interfacing to systems with different output-return requirements. The output can also be combined for OR-style logic, although exact implementation depends on the surrounding circuit and output configuration. Typical uses include precision threshold detection, sensor signal conditioning, window comparison, overvoltage indication, zero-crossing detection, and industrial control systems. The 250 ns response is suitable for systems that need faster decisions than general-purpose slow comparators while retaining wide input-voltage capability. Designers must account for the obsolete lifecycle status, supply arrangement, input common-mode limits, output polarity, and thermal constraints. The verified manufacturer result identifies LT111A as obsolete and directs users to contact Analog Devices for a replacement product. New designs should therefore confirm availability, lifecycle status, and any recommended replacement before committing to production. This page consolidates the verified manufacturer specifications, obsolete-status notice, package information, design guidance, and sourcing limitations for engineers comparing the LT111A with legacy comparator systems.

RFQ Contact
LT111AH Military Voltage Comparator | Analog Devices
LT111AH

LT111AH Military Voltage Comparator | Analog Devices

The Analog Devices LT111AH is a military-grade, single voltage comparator supplied in an 8-terminal round TO-5 package. It compares one input voltage level with another and provides a logic-level output suitable for threshold, window, zero-crossing, and sensing functions. The verified product data identifies it as an IC voltage comparator, specifies an 8-wire terminal configuration, and states a maximum operating temperature of 125°C. Exact input common-mode limits, output-current capability, propagation delay, and offset parameters are not present in the supplied records. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output when the difference crosses a defined threshold. Within the broader semiconductor hierarchy, a comparator belongs to the linear IC family and the amplifier IC category. Unlike a general-purpose operational amplifier, its principal purpose is fast, deliberate state transition according to the polarity of its differential input rather than linear amplification. The LT111AH is associated with the LT111 comparator family and is offered in a military temperature grade. The H suffix distinguishes this ordering code from other package, temperature, or accuracy variants, but the supplied excerpts do not expose the underlying ordering-code table needed to state every suffix characteristic. Its TO-5 construction uses wire-form leads and suits legacy or ruggedized assemblies where a through-hole metal package is preferred. The round package also requires care during insertion because lead orientation determines correct comparison-input and output connections. Verified distributor records classify the part as a comparator and show commercial listings through DigiKey, Octopart, Xecor, and other suppliers. The available Cytech Systems result reports zero stock and $0.0000 reference prices, so those values cannot be interpreted as a usable quotation. The Linear Technology page indexed by linear-electronic.com reports 3,320 pieces in stock, but that vendor record is not treated as an authoritative global stock figure. Pricing and availability should therefore be confirmed at order time. The LT111AH can be evaluated for industrial control, instrumentation, alarm detection, and legacy equipment, provided the system supply stays within the family limits. External resistors and protection networks may be needed to constrain inputs or accelerate an open-collector output, but exact values cannot be selected responsibly without verified input thresholds, output architecture, supply range, and timing specifications. This page combines the verified source excerpts with explicit data gaps rather than inferring unseen electrical limits. The primary engineering task is to verify the manufacturer datasheet before layout signoff, especially for supply voltage, common-mode range, output sink current, offset voltage, response time, and the exact TO-5 pin map. For replacement work, engineers should require both mechanical equivalence and pin-level compatibility rather than relying only on the comparator function. A device that performs the same threshold decision but exposes different pins or output behavior is not necessarily interchangeable in production. This page distinguishes verified facts from unavailable parameters, consolidates distributor and datasheet links, and provides replacement and design guidance for engineers evaluating the LT111AH. Commercial prices are reported as of 2026-10-22 only where a source supplied a value; otherwise a quote is required.

RFQ Contact
LT1124CJ8 - Dual Precision Op Amp | Analog Devices
LT1124CJ8

LT1124CJ8 - Dual Precision Op Amp | Analog Devices

Analog Devices LT1124CJ8 is a dual, low-noise, high-speed precision operational amplifier with two independent amplifier circuits in an 8-pin CERDIP package. The device provides higher gain, slew rate, and bandwidth than the industry-standard OP-27 and competing OP-270/OP-470 families, while offering lower input bias current and input offset current than the OP-27 and lower offset voltage and noise than the OP-270/OP-470. Its ±22 V supply capability supports a broad range of precision signal-conditioning, instrumentation, and audio applications. An operational amplifier is a high-gain differential amplifier used to amplify small signals, buffer sensors, implement active filters, and serve as the central active element in control and measurement circuits. The LT1124 belongs to the operational-amplifier hierarchy within analog signal-chain ICs, combining high open-loop gain, low offset voltage, low noise, and fast slew performance in one dual-amplifier package. The LT1124 family is designed for applications requiring more precision and speed than conventional general-purpose amplifiers. Analog Devices identifies higher gain, slew rate, and bandwidth than the OP-27 as principal family advantages. Relative to the OP-27, the LT1124 also provides lower input bias current and input offset current. Relative to the OP-270 and OP-470, it offers lower offset voltage and lower noise. Two amplifiers in one package reduce external component count and board area when a circuit requires matched dual signal paths. Typical uses include instrumentation amplifiers, low-level sensor preamplifiers, precision filters, audio preamplification, and reference or measurement chains. The ceramic DIP package supports through-hole construction and is suitable for legacy industrial, test, and measurement equipment where leaded packages remain practical. The ±22 V operating range permits operation from conventional positive, negative, or split supply rails, subject to the complete device limits in the Analog Devices datasheet. Applications should also preserve adequate input common-mode range, output swing, stability compensation, and output-load capability for the selected feedback network. For PCB design, place the power and ground pins directly on the supply planes, keep feedback components close to the relevant amplifier inputs, and route sensitive input nodes away from switching nodes and high-current return paths. Because the LT1124CJ8 is a through-hole CERDIP device, check connector spacing, hole pattern, and mechanical clearance before finalizing a board revision. This product page organizes the LT1124CJ8 specifications, package information, sourcing path, and application guidance. It also distinguishes verified performance claims from unspecified electrical details that should be confirmed in the manufacturer datasheet before precision design work is released for production.

RFQ Contact
LT1125CJ - Quad Precision Op Amp | Analog Devices | Instrumentation
LT1125CJ

LT1125CJ - Quad Precision Op Amp | Analog Devices | Instrumentation

The Analog Devices LT1125CJ is a quad low-noise, high-speed precision operational amplifier packaged in a 14-pin CERDIP. The device provides four amplifier channels in one through-hole package, making it useful when a circuit requires multiple precision signal-conditioning stages without allocating separate packages for each channel. The LT1125 family is positioned for instrumentation and other applications where low-noise, high-speed amplification and higher gain performance are important. An operational amplifier, commonly called an op amp, is an active semiconductor component that uses high gain and negative feedback to amplify small voltage differences. It belongs to the amplifier IC hierarchy, where precision operational amplifiers are selected when signal fidelity, offset behavior, bias-current characteristics, and open-loop performance matter more than the lowest possible cost or smallest footprint. The LT1125 uses a four-channel architecture, with the “quad” configuration providing four amplifier sections in one package. Its operating class is described by Analog Devices as low noise, high speed, and precision. These characteristics make it suitable for low-level sensor conditioning, instrumentation amplification stages, and analog signal chains in which multiple channels must be handled consistently. The C suffix identifies the commercial temperature-grade family, while the J suffix denotes the through-hole ceramic dual-inline package used by LT1125CJ. The manufacturer describes the LT1125 as offering higher gain, slew rate, and bandwidth than the industry-standard OP-27 and competing OP-470 families. These comparisons are relevant when upgrading an existing precision-amplifier design, but the actual signal bandwidth, noise density, input offset voltage, input bias current, input voltage range, and output swing must be checked against the system requirements before replacing another amplifier. Typical uses include four-channel instrumentation front ends, low-level transducer signal conditioning, precision measurement systems, laboratory interfaces, and factory test equipment. The LT1125CJ is particularly appropriate when a through-hole ceramic package is preferred, four amplifier channels are required, and the design benefits from the family’s stated low-noise, high-speed, and precision characteristics. It can also simplify assembly by reducing the number of amplifier packages on a board. The principal design consideration is package-level thermal management. A 14-pin CERDIP offers a larger thermal path and more forgiving assembly characteristics than a small surface-mount package, but it consumes substantially more board area. Confirm pin orientation, supply requirements, input common-mode range, output swing, stability requirements, and decoupling directly from the manufacturer datasheet before laying out the PCB. This product record combines the exact ordering information, package details, family positioning, manufacturer product information, and replacement-search results into an engineering-oriented reference. It also highlights where a genuinely pin-compatible replacement must be qualified rather than assuming that a similar amplifier has the same pinout, supply behavior, or precision performance.

RFQ Contact
LT1126CJ8 - 65MHz Dual Op Amp | Analog Devices
LT1126CJ8

LT1126CJ8 - 65MHz Dual Op Amp | Analog Devices

The Analog Devices LT1126CJ8 is a dual, decompensated, general-purpose operational amplifier with a 65 MHz gain-bandwidth product and an 11 V/µs slew rate, housed in an 8-CERDIP through-hole package. It combines low-noise precision-amplifier characteristics with the enhanced alternating-current performance associated with decompensated operation. The device contains two amplifiers in one package and is intended for applications requiring higher speed and bandwidth than the LT1124 and LT1125 families. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to compare an input signal with a feedback network. The LT1126 belongs to the precision-op-amp, voltage-feedback amplifier, signal-conditioning IC, and power-management-support hierarchy. Decompensation deliberately reduces closed-loop stability at lower gain in exchange for faster large-signal behavior and wider bandwidth, making this family useful in high-speed instrumentation and signal-processing paths. The principal performance figures are a 65 MHz gain-bandwidth product and an 11 V/µs slew rate. Its dual configuration supports two independent signal channels, while the 8-CERDIP package provides through-hole construction for industrial and legacy equipment. The family description also identifies low-voltage noise, high voltage gain, low offset voltage, and low supply-current-per-amplifier characteristics. These features make the LT1126 appropriate where amplifier accuracy must coexist with rapid signal transitions. Decompensated operation requires the circuit designer to select a suitable noise gain and verify stability at the intended closed-loop gain. At unity gain, the amplifier is typically decompensated and may require external compensation or a higher noise-gain setting. Component tolerances, capacitive loading, and the feedback network should therefore be evaluated together rather than relying only on the nominal gain-bandwidth product. Typical uses include low-level signal conditioning, precision measurement systems, active filtering, data acquisition, instrumentation, and industrial control. The dual package can also reduce board area when a design needs two amplifiers with consistent performance. Its combination of 65 MHz bandwidth and 11 V/µs slew rate is particularly relevant to wideband transimpedance, buffer, and feedback-network designs where the LT1124 or LT1125 would provide less AC performance. Designers should use the manufacturer pin-description table when assigning PCB connections and should confirm stability at every intended gain and capacitive-load condition. Input and output buffering, power-supply bypassing, grounding, and output-load limits remain important. The ceramic DIP construction also requires adequate board spacing and through-hole assembly planning, particularly where long leads can add parasitic inductance at high frequency. This product record combines the verified LT1126 family specifications with application-focused engineering guidance, practical stability considerations, package information, and a comparison of available same-family temperature-grade alternatives. It is intended to help engineers evaluate the LT1126CJ8 for dual-channel precision signal paths while distinguishing the industrial-grade CJ8 version from related ceramic-DIP variants.

RFQ Contact
LT1127CJ - Quad High-Speed Precision Op Amp | Analog Devices
LT1127CJ

LT1127CJ - Quad High-Speed Precision Op Amp | Analog Devices

Analog Devices LT1127CJ is a quad, decompensated, low-noise, high-speed precision operational amplifier packaged in a 14-pin CERDIP. The device contains four amplifiers and is stable at a closed-loop gain of 10 or higher. Its decompensated architecture provides higher slew rate and bandwidth than the LT1124 dual and LT1125 quad operational amplifiers while preserving the DC specifications of those devices. The LT1127 therefore occupies the linear-regulator-to-precision-signal-chain role where multiple channels must amplify small signals without being operated as unity-gain amplifiers. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification and negative feedback to control gain, bandwidth, output impedance, and signal integrity. A precision operational amplifier adds low offset, low bias-current, and noise-related performance for instrumentation, measurement, active filtering, and signal-conditioning systems. The LT1127 is specifically a decompensated amplifier: its compensation supports stable operation at higher closed-loop gain rather than the unity-gain stability expected from conventional voltage-feedback amplifiers. The LT1127 family provides four amplifiers in one package, reducing component count and board area when several precision channels are required. Its defining performance advantage is the combination of increased AC performance with unchanged DC characteristics relative to the LT1124 and LT1125 families. The manufacturer describes the LT1126/LT1127 as high-performance, low-noise, high-speed precision op amps with stability at a gain of 10 or more. This makes the family applicable to instrumentation amplifiers, active filters, low-level sensor interfaces, and analog control loops whose architecture already provides adequate loop gain at a closed-loop gain of 10. The LT1127CJ is the 14-pin CERDIP orderable designation within the LT1127 family. A ceramic dual in-line package provides a through-hole mechanical format for industrial and legacy-style equipment, while the quad channel count supports four independent amplifier sections. Applications include four-channel sensor conditioning, multi-channel active filtering, buffered instrumentation inputs, precision signal amplification, and industrial measurement systems. The decompensated architecture makes gain planning essential: feedback networks should be designed around a minimum stable closed-loop gain of 10. Designers should account for the package's thermal environment, input and output signal limits, supply voltage, and the feedback network when using the LT1127CJ. Because the device is decompensated, using it as a unity-gain buffer is not the intended operating mode. Confirming offset, bias-current, noise, slew-rate, bandwidth, supply-current, and temperature limits in the manufacturer datasheet is necessary before fixing the production design. This product page organizes the exact LT1127CJ identity, package information, manufacturer documentation, engineering use cases, and sourcing path in one place. It also highlights the principal selection constraint—stable operation at a gain of 10 or higher—so engineers can distinguish this decompensated precision amplifier from conventional unity-gain-stable op amps before beginning PCB or schematic work.

RFQ Contact
LT1130CNW - 5V RS-232 Transceiver | Analog Devices | 28-PDIP
LT1130CNW

LT1130CNW - 5V RS-232 Transceiver | Analog Devices | 28-PDIP

Analog Devices LT1130CNW is a low-power RS-232 transceiver with five integrated drivers and five integrated receivers, designed for 5V data-link equipment. The device is available in a 28-pin plastic dual inline package, identified by the 28-PDIP designation in the manufacturer and distributor product records. Its five-driver, five-receiver arrangement consolidates bidirectional RS-232 signal conditioning into one interface IC while reducing the number of external components required for multi-channel serial links. An RS-232 transceiver is an interface IC that combines line drivers, line receivers, and the electrical protection characteristics needed for RS-232 communication. The LT1130CNW belongs to the broader line-driver and line-receiver hierarchy, placing it within interface ICs used to connect data-processing equipment to computers, terminals, controllers, and industrial communication equipment. Its 5V-oriented design is suited to systems where logic-side supply voltage and RS-232 interface requirements are compatible. The LT1130CNW integrates five drivers and five receivers in one package. This channel count supports equipment that needs several RS-232 ports or a mixture of transmit and receive lines. Its low-power orientation is useful where the design objective is to reduce interface-circuit energy use while maintaining established RS-232 behavior. The exact propagation delay, slew rate, input capacitance, output protection, and operating-temperature limits must be confirmed from the manufacturer datasheet before a new design is released. The device belongs to the Analog Devices and Linear Technology RS-232 interface family. Linear Technology originally marketed the LT1130 series, while current distributor records identify LT1130CNW as an Analog Devices Inc. product. The N suffix identifies the industrial-temperature package treatment, while W identifies the 28-pin plastic DIP configuration. These suffix conventions should be checked against the ordering information before substituting another package or grade. Typical applications include multi-channel RS-232 ports in industrial controllers, test equipment, data acquisition systems, embedded serial interfaces, and legacy peripheral connectivity. A multi-drop or multi-port design can use the integrated drivers and receivers to reduce board area, although system-level considerations such as cable length, ground reference, connector protection, and signal integrity remain important. The principal design consideration is confirming every electrical limit against the correct LT1130 datasheet revision. Designers should verify supply voltage, driver output levels, receiver thresholds, input capacitance, shutdown or enable behavior where applicable, and package pin assignments. Place bypass capacitance close to the supply pins and provide connector-side protection appropriate to the installation environment. This page consolidates the exact package and channel-count information, comparison dimensions, application guidance, and replacement-screening criteria needed to evaluate LT1130CNW. Because only the exact MPN and general interface description are documented here, unspecified electrical values are clearly marked rather than guessed, enabling engineering review without introducing unsupported electrical claims.

RFQ Contact
LT1131CNW - 5/4 RS232 Transceiver | Analog Devices
LT1131CNW

LT1131CNW - 5/4 RS232 Transceiver | Analog Devices

Analog Devices LT1131CNW is a 5/4 RS-232 transceiver designed for low-power, low-voltage communications equipment. The device combines five driver outputs and four receiver inputs in a 28-pin PDIP package, making it suitable for systems that require multiple serial data channels and limited board space. The verified product listing identifies the LT1131CNW as a 28-pin PDIP RS232 transceiver from Analog Devices. An RS-232 transceiver is an interface IC that converts logic-level signals between a digital system and RS-232 differential signaling. The transmitter section converts digital data into RS-232-compatible outputs, while the receiver section converts incoming RS-232 signals into digital logic levels. A 5/4 configuration means five drivers share the package with four receivers, allowing designers to support several communications ports or mixed control and data links. The LT1131 family is associated with Advanced Low Power 5V RS232 Drivers/Receivers with Small Package Size. The LT1131CNW is offered in a through-hole PDIP package, which can simplify prototyping, inspection, and repair compared with a surface-mount package. The commercial temperature grade and through-hole terminal form make the part relevant to industrial-control, instrumentation, embedded-console, and legacy peripheral designs. The LT1131CNW is useful where multiple RS-232 channels are required but board area and power consumption must be controlled. Because the device is a multi-channel interface rather than a power semiconductor, no safe-operating-area chart applies. Designers should verify electrical limits, receiver thresholds, driver slew behavior, supply requirements, and pin assignments against the manufacturer datasheet before laying out a new circuit. Typical uses include RS-232 port expansion, industrial test equipment, serial adapters, programmable controllers, and embedded systems that retain a legacy communication interface. The 28-pin PDIP footprint is also convenient for through-hole industrial control boards where a compact surface-mount package would be inconvenient to assemble. The most important design step is to preserve the correct pin mapping and bypass-capacitor layout when creating a replacement board. Place required decoupling capacitors close to the supply pins, route each RS-232 driver and receiver according to the datasheet, and allow adequate signal-transition headroom for the selected data rate. This page combines the verified package and product classification with practical selection, replacement, and layout guidance.

RFQ Contact
LT1132CN - Low-Power RS-232 Transceiver | Analog Devices
LT1132CN

LT1132CN - Low-Power RS-232 Transceiver | Analog Devices

The Analog Devices LT1132CN is a low-power RS-232 line transceiver with integrated drivers and receivers in a 24-pin through-hole DIP package. The verified source data identifies it as a commercial-temperature line transceiver with 24 terminals, a rectangular DIP package, and through-hole mounting. It is designed for systems that need bidirectional serial data transmission over RS-232 links, including computer serial ports, industrial control links, data-acquisition equipment, and embedded control systems. An RS-232 transceiver is an interface IC that converts between digital logic-level signals and RS-232 line-level voltages. The LT1132CN combines transmitter and receiver functions in one package, reducing the number of interface components required in a serial port. In the broader electronics hierarchy, it belongs to interface ICs, line drivers and receivers, communication transceivers, and RS-232 interface devices. Its commercial-grade classification makes it relevant to equipment operating in ordinary commercial environments, although detailed temperature limits were not present in the supplied data. The verified listing identifies the LT1132CN as a LINE TRANSCEIVER and supplies the package basics: 24 terminals, DIP package code, rectangular package shape, and through-hole terminal form. The supplied search results also associate the LT1132 family with low-power 5 V RS-232 drivers and receivers, but exact voltage, current, propagation-delay, driver-strength, receiver-threshold, and logic-level values are not provided. Those parameters should be confirmed in the manufacturer datasheet before final circuit design. The transceiver can be used to connect a host controller to an RS-232 data link, especially where a compact, multi-function interface is preferred over separate driver and receiver ICs. Because this is a through-hole DIP device, it is well suited to through-hole prototypes, legacy equipment, repair applications, and industrial controller boards where a large package and socketed assembly are acceptable. The DIP outline also simplifies inspection and replacement, but it requires more board area than a surface-mount equivalent. A key design consideration is that RS-232 uses voltage levels and signal polarity that are not directly compatible with ordinary CMOS or TTL logic. The transceiver handles that conversion, but the system still needs correct decoupling, grounding, connector protection, cable-length planning, and appropriate handling of unused enable or control pins. Because the supplied data does not specify exact pin names or all electrical limits, the LT1132CN pinout should be taken from the official datasheet rather than inferred from the package outline. This page consolidates the verified distributor and manufacturer-related links for the LT1132CN, identifies the confirmed commercial DIP package information, and separates verified facts from parameters that still require datasheet confirmation. It also records the absence of verified pricing, lifecycle, compliance, pin-level, and direct drop-in replacement data to avoid presenting unsupported engineering assumptions.

RFQ Contact
LT1167CS8 - Precision Sensor INA | Analog Devices
LT1167CS8

LT1167CS8 - Precision Sensor INA | Analog Devices

Analog Devices LT1167CS8 is a low-power, precision instrumentation amplifier with a single-resistor gain setting from 1 to 10,000, 7.5 nV/√Hz voltage noise at 1 kHz, and an 8-pin SOIC package. It operates from ±18 V according to the manufacturer product documentation and is designed for accurate amplification of low-level differential sensor signals. An instrumentation amplifier is a differential amplifier optimized for measuring small signals embedded in larger common-mode voltages. The LT1167CS8 combines high input impedance, precise gain control, and common-mode rejection in one compact package. This makes it suitable within the measurement-instrumentation amplifier category for bridge sensors, biomedical signals, and precision analog front ends where a conventional operational amplifier would require additional matching resistors or differential input stages. The defining feature is single-resistor gain programming. Setting the external gain resistor between the designated gain pins establishes gains from 1 to 10,000 without the dual-resistor networks often required by three-amplifier instrumentation amplifiers. A 7.5 nV/√Hz noise density at 1 kHz supports low-noise measurement, while the 0.9 mA typical supply current supports low-power operation across a 2.3 V to 15 V supply range. Its three-amplifier architecture provides differential input handling and high common-mode rejection. The manufacturer states that two external 5 kΩ resistors allow the LT1167 to pass the IEC 1000-4-2 Level 4 electrostatic-discharge specification. This protection capability is useful when the sensor interface can be connected to an external cable or touch-accessible equipment. Typical uses include strain-gauge and load-cell front ends, isolated sensor measurement, precision bridge excitation, medical instrumentation, and low-level process-control signals. The 8-pin SOIC package also reduces board area compared with discrete multi-amplifier and precision-resistor implementations, simplifying signal-chain integration. Design attention should be concentrated on gain-resistor selection, input filtering, reference grounding, supply bypassing, and common-mode-range checks. Stable gain requires suitable resistor construction and layout, while high-gain operation amplifies thermal and layout-induced errors. Confirm the complete operating limits and pin assignments in the manufacturer datasheet before releasing a PCB. This product page consolidates manufacturer specifications, package and pin information, qualified same-footprint alternatives, application guidance, and design checks into a practical engineering reference for selecting and implementing the LT1167CS8.

RFQ Contact
LT1167IS8 - Precision InAmp, Single-Resistor Gain, SOIC-8 | Analog Devices
LT1167IS8

LT1167IS8 - Precision InAmp, Single-Resistor Gain, SOIC-8 | Analog Devices

The Analog Devices LT1167IS8 is a low-power, precision instrumentation amplifier (InAmp) that requires only one external resistor to set any gain from 1 to 10,000, housed in an 8-pin SOIC package. Key specifications include 7.5 nV/√Hz input voltage noise density at 1 kHz, 60 µV maximum offset voltage, 1.2 V/µs slew rate, 1 MHz gain-bandwidth product, and 0.9 mA typical supply current on ±2.3V to ±18V supplies. An instrumentation amplifier is a specialized differential amplifier topology designed to extract a small differential signal riding on a large common-mode voltage. The internal three-op-amp architecture provides high common-mode rejection ratio (CMRR), high input impedance on both inputs, and a single external gain-setting resistor (RG), dramatically simplifying precision signal-chain design compared to discrete implementations. The LT1167 belongs to the analog-front-end / signal-conditioning IC category, sitting between sensors and ADCs in measurement systems where low noise and high CMRR are paramount. The single-resistor gain programmability eliminates the matched-resistor pairs required by classic InAmp topologies - any gain from G=1 (RG open) to G=10,000 (RG=60.4Ω) is set by one standard-value resistor, which simplifies calibration and reduces bill-of-material cost. The LT1167 also passes the IEC 1000-4-2 level 4 ESD specification on the inputs when used with two 5 kΩ protection resistors, making it robust for industrial sensor interfaces. Typical applications include weigh scales and load-cell bridges, ECG and biomedical front-ends, thermocouple amplifiers, industrial process-control transducer conditioning, and precision data-acquisition systems. The wide ±2.3V to ±18V supply range and 8-pin SO footprint make it a drop-in upgrade path for legacy AD620, INA128 and similar 3-op-amp InAmp sockets. When designing with the LT1167, place the gain-setting resistor close to the RG pins to minimize parasitic capacitance, and provide an output-referred filter capacitor if driving long cables to prevent capacitive loading instability. The reference pin (REF) should be driven by a low-impedance source or decoupled with 0.1 µF to ground for optimal CMRR. This page synthesizes verified distributor pricing, parametric drop-in alternatives (same-package and pin-compatible), and practical design notes that go beyond the Analog Devices datasheet table alone.

RFQ Contact
LT1179ACJ - 4-Channel Micropower Precision Op Amp | Analog Devices
LT1179ACJ

LT1179ACJ - 4-Channel Micropower Precision Op Amp | Analog Devices

Analog Devices LT1179ACJ is a micropower, four-channel precision operational amplifier optimized for single-supply operation at 5 V, with additional specifications defined at ±15 V supplies. The device uses a maximum supply current of 17 µA and provides four amplifiers in a 14-pin ceramic dual in-line package. According to the manufacturer product page, its low supply current is combined with precision specifications including 30 µV offset voltage and low offset current. An operational amplifier, or op amp, is a high-gain analog building block used to amplify small voltage signals. The LT1179 belongs to the precision operational amplifier category and then to the broader amplifier IC and semiconductor hierarchies. Its four independent channels make it useful wherever several low-level signals must be conditioned while keeping power consumption and board area low. The LT1179ACJ is designed around the micropower precision amplifier concept. Each channel provides high open-loop gain, low input offset voltage, and low input bias behavior while operating from a single 5 V supply. The 17 µA maximum supply-current figure makes the device relevant to battery-powered instrumentation, portable measurement systems, and industrial controls where amplifier power can dominate the standby budget. Operation at ±15 V also supports higher-level bipolar signal chains. The four-channel architecture reduces the number of packages required when a design needs multiple amplification paths. A single LT1179ACJ can implement four amplifiers instead of using four separate single or dual amplifier packages. This simplifies inventory, reduces board-level component count, and can lower assembly cost. The tradeoff is that all four channels share one package and one supply, so a fault or power-distribution problem can affect more than one signal path. Typical uses include low-level sensor amplification, current-to-voltage conversion, instrumentation buffering, precision bridge excitation, active filtering, and general-purpose analog signal conditioning. The device can be especially useful in portable instruments where four precision channels are needed but each channel's operating current must remain low. Supply bypassing and input-common-mode limits should still be checked against the manufacturer's operating conditions. For PCB design, place the bypass capacitor close to the positive and negative supply pins and maintain short, low-noise paths from sensitive inputs. Ceramic input filtering should account for input-bias-current effects rather than treating every capacitor value as ideal. Ceramic-DIP construction also requires adequate mechanical clearance and proper socket or soldering practices. This page combines the manufacturer's LT1179 family information with distributor package details and practical guidance for precision, low-power analog design. It also distinguishes the directly comparable family variants while making clear where a new schematic review is required before selecting a replacement.

RFQ Contact
LT1179CJ - 17uA Quad Precision Op Amp | Analog Devices
LT1179CJ

LT1179CJ - 17uA Quad Precision Op Amp | Analog Devices

Analog Devices LT1179CJ is a micropower quad precision operational amplifier supplied in a 14-pin CERDIP package. The device is optimized for single-supply operation at 5V and is also specified at ±15V supplies. Each amplifier features a maximum supply current of 17uA, maximum offset voltage of 70uV, maximum offset current of 250pA, and maximum input bias current of 5nA. A precision operational amplifier is a low-noise, high-gain analog signal-conditioning device used to amplify weak sensor, instrumentation, control, and feedback signals. The LT1179CJ belongs to the micropower operational-amplifier category, combining four amplifiers in one package with very low supply-current demand. This makes it suitable for battery-powered instrumentation and other systems where amplifier power consumption must remain small. The LT1179CJ is specified as a general-purpose, four-circuit amplifier. Its precision characteristics include low offset voltage, low offset current, and low input bias current, helping reduce signal error when the amplifier is used with sensors, transducers, or high-impedance sources. The device is intended for single-supply systems, where the output signal must be biased above ground, as well as conventional dual-supply circuits using ±15V. The LT1179CJ can be used in low-power sensor interfaces, precision signal-conditioning circuits, instrumentation amplifiers, data-acquisition front ends, battery-powered measurement systems, and low-current feedback loops. Its 17uA-per-amplifier maximum supply current is particularly useful when four active amplifiers would otherwise contribute a larger aggregate supply-current requirement. For single-supply operation, confirm the input and output common-mode range, output swing, and load requirements against the manufacturer datasheet before finalizing the biasing network. Decoupling capacitors should be placed close to the power pins, and unused amplifier channels should be configured according to the recommended stable-output method. This product page combines the manufacturer product information, distributor package identification, and application-oriented engineering guidance. Use the official Analog Devices datasheet for the complete electrical characteristics, pin assignments, ordering information, and test conditions.

RFQ Contact
LT1206CR - 250mA, 60MHz Current Feedback Amplifier | Analog Devices
LT1206CR

LT1206CR - 250mA, 60MHz Current Feedback Amplifier | Analog Devices

Analog Devices LT1206CR is a single current-feedback operational amplifier with 250mA minimum output drive current and 60MHz bandwidth in a 7-lead DDPAK package. The device is optimized for video and other applications requiring high slew rate, wide bandwidth, and the ability to drive large capacitive loads while maintaining stable operation. Its high-impedance input is specified at 10M ohms, and its adjustable supply-current architecture provides additional control for power-sensitive designs. A current-feedback amplifier is a voltage-input, current-output feedback topology within the broader operational-amplifier and analog signal-conditioning product hierarchy. Unlike a conventional voltage-feedback amplifier, the LT1206CR controls a differential current rather than an error-voltage gain, enabling wide bandwidth and high slew-rate performance while preserving low distortion. It is positioned as an analog amplifier IC for video, communications, and signal-chain systems that need more output drive than a general-purpose op amp provides. Verified manufacturer information identifies 250mA minimum output drive, 60MHz bandwidth, a 900V/us maximum slew-rate value, 0.02% differential-gain error, and 0.17 degrees differential phase. The device operates across a wide supply range and accepts supplies up to ±15V. A shutdown function places the amplifier in a high-impedance, low-current mode, with shutdown current below 200uA, helping reduce dissipation when the circuit is inactive. The LT1206 is particularly suitable for video because it combines high bandwidth, high output current, and excellent video characteristics. It is also stable with large capacitive loads and can supply the current required by capacitive input and output networks. The adjustable supply-current feature allows engineers to balance performance and power consumption according to the source impedance, load, and operating conditions of a specific board. Typical uses include video buffering, cable-driver interfaces, active video filters, video distribution, communications equipment, and test and measurement systems. In these applications, the 60MHz bandwidth and 250mA output-current capability provide useful margin for signal transmission and load driving, while the shutdown feature supports systems that periodically disable the amplifier. When laying out the circuit, use short feedback paths, maintain the feedback network close to the amplifier, and account for the DDPAK-7 thermal-pad connection when calculating copper heat spreading. Because the exact pin names and exposed-tab assignment are not present in the supplied verified snippets, the package drawing is not populated rather than presenting an unverified pinout. Consult the official LT1206 datasheet before PCB release or substitution. This page consolidates the verified Analog Devices product information, distributor availability references, package details, and practical selection guidance for the LT1206CR. It also distinguishes device-level evidence from unresolved replacement and pricing data, helping engineers avoid treating generic op-amp alternatives as true pin-compatible drop-ins.

RFQ Contact
LT1209CS - Quad 45MHz 400V/µs Op Amp | Analog Devices
LT1209CS

LT1209CS - Quad 45MHz 400V/µs Op Amp | Analog Devices

Analog Devices LT1209CS is a quad, very-high-speed operational amplifier with 45 MHz gain-bandwidth product, 400 V/µs slew rate, and unity-gain stability in a 16-lead SOIC package. Each of its four amplifier channels uses a single-gain-stage architecture designed for accurate, fast settling. The LT1209CS operates from a wide supply range, with ±15 V operation explicitly identified as a minimum configuration, and consumes 7 mA per amplifier. An operational amplifier is a high-gain differential amplifier whose feedback network determines its behavior. The LT1209 belongs to the general-purpose operational-amplifier hierarchy, combining high speed with improved DC characteristics. It is a voltage-feedback amplifier designed to serve as a unity-gain buffer, a signal amplifier, or the active element in instrumentation and data-acquisition circuits. Compared with slower general-purpose devices, its principal advantage is rapid large-signal response rather than micropower operation. Key features include a 45 MHz gain-bandwidth product, 400 V/µs slew rate, and a 90 ns settling time to 0.1% for a 10 V step. The listed DC gain is 7 V/mV, while the maximum input offset voltage is reported as 3 mV in the LT1208/LT1209 datasheet summary. Unity-gain stability allows direct operation without compensation or added closed-loop gain, and the single-gain-stage architecture gives the device outstanding settling characteristics. The LT1209CS combines the speed of a high-speed voltage-feedback amplifier with DC performance suited to general instrumentation. Its wide supply range permits operation near ±15 V, while the minimum output swing of ±12 V into 500 ohms provides useful output range for bipolar signal chains. The 7 mA supply current per amplifier is a meaningful tradeoff: fast settling and slew performance are obtained at a higher supply current than typical low-power op amps. Typical uses include high-speed data acquisition, active filtering, sample-and-hold buffers, waveform conditioning, video or communications signal paths, and instrumentation requiring rapid settling. In a data-conversion system, the amplifier can drive or buffer an ADC input while preserving pulse amplitude and timing. In active filters, its 45 MHz bandwidth and 400 V/µs slew rate support signal paths whose operating frequency is comfortably below those limits. Designers should preserve adequate output-voltage headroom and verify capacitive-load stability with the actual output network. Input and feedback resistances also determine gain-bandwidth and noise behavior, so practical resistor values should be selected rather than relying on the nominal 7 V/mV open-loop gain. Stable reference grounding and short feedback paths are important because the device’s high speed can expose board-level parasitic capacitance. This page consolidates the available manufacturer and distributor information for the LT1209CS, distinguishes verified device characteristics from unavailable data, and provides practical selection and design guidance. It also distinguishes genuine drop-in alternatives from related package or ordering variants that should not be treated as automatic replacements.

RFQ Contact
LT1210CR - 1.1A, 35MHz Current Feedback Amplifier | Analog Devices
LT1210CR

LT1210CR - 1.1A, 35MHz Current Feedback Amplifier | Analog Devices

The Analog Devices LT1210CR is a current feedback operational amplifier delivering a minimum 1.1 A of output drive current with a 35 MHz small-signal bandwidth and a 900 V/µs slew rate, housed in a 7-pin DDPAK (TO-263) surface-mount package. It operates from ±15 V supplies (single supply up to 30 V) and combines high output current with excellent large-signal characteristics, making it suitable for driving low-impedance loads such as cables, transformers, and power transistors at frequencies in the 1 MHz to 2 MHz range. A current feedback amplifier (CFA) is a class of op-amp whose inverting input impedance is intentionally low and whose small-signal bandwidth is set primarily by the feedback resistor rather than the closed-loop gain. CFAs therefore maintain near-constant bandwidth across a wide range of gains, in contrast to voltage feedback amplifiers whose gain-bandwidth product is fixed. Within the power-management and signal-chain taxonomy, the LT1210CR sits in the high-current buffer / line-driver niche: amplifier -> operational amplifier -> current feedback amplifier -> power op-amp -> analog signal chain IC. Key features of the LT1210CR include a 10 MΩ high input impedance, ±15 V supply operation, short-circuit protection, thermal shutdown, and an optional shutdown pin that pulls the quiescent current below 200 µA. The shutdown pin is internally biased to the positive rail, which allows simple open-drain (open-collector) logic control using a 5 V buffer. A wide supply range and stable operation with large capacitive loads make the device rugged in real-world cable-driving and piezo-driver circuits. Architecturally, the LT1210 uses a complementary output stage and current-mode feedback topology to achieve high slew rate independent of gain-setting resistor values. The combination of 35 MHz bandwidth and 900 V/µs slew rate allows full-power operation up to several MHz before slewing-induced distortion dominates, which is uncommon in standard op-amps of similar output current capability. Typical applications include video and RGB line drivers, twisted-pair line drivers, low-impedance cable drivers, piezo transducer drivers, headphone amplifiers, motor driver signal stages, and power-MOSFET gate drivers. The 7-pin DDPAK (TO-263) package provides a low thermal resistance (θJA ≈ 30 °C/W on a 1 in² copper pour) so that the 1.1 A output stage can be used continuously without external heatsinking at moderate ambient temperatures. When designing with the LT1210CR, pay close attention to the feedback resistor value — a 1 kΩ resistor typically yields 35 MHz bandwidth in the non-inverting configuration. Place supply bypass capacitors (≥ 0.1 µF ceramic in parallel with ≥ 4.7 µF tantalum or electrolytic) within 5 mm of the supply pins to maintain stability at high output currents. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the LT1210CR against competing high-current op-amps.

RFQ Contact
LT1211IS8 - Dual 14MHz Precision Op Amp | Analog Devices
LT1211IS8

LT1211IS8 - Dual 14MHz Precision Op Amp | Analog Devices

The Analog Devices LT1211IS8 is a dual, single-supply precision operational amplifier featuring a 14MHz gain-bandwidth product, a 7V/us slew rate, and an 8-lead small-outline IC package. The LT1211 family is designed for applications requiring both DC precision and comparatively high-frequency amplification. Its two amplifiers are independently usable, allowing one package to provide signal conditioning for two related analog channels. An operational amplifier is an analog amplifier whose behavior depends mainly on external feedback components. A precision operational amplifier adds low offset, low bias-current, and stable DC characteristics, while a gain-bandwidth product specifies the approximate frequency range over which closed-loop gain and phase performance can be maintained. The LT1211 belongs to the operational-amplifier hierarchy within analog and linear semiconductor devices. The LT1211 combines a 14MHz gain-bandwidth product with a 7V/us slew rate. These characteristics make it relevant to low-level signal conditioning, active filtering, instrumentation, and feedback loops that require faster dynamic response than a conventional low-frequency precision amplifier. The manufacturer identifies LT1212 as the quad version of the same amplifier family, allowing family-level design planning without changing the core amplifier architecture. The LT1211IS8 is specified for single-supply operation. Single-supply operation simplifies circuit design when the source signal lies near the lower supply rail, although the usable common-mode range, output swing, and biasing requirements remain important design constraints. Designers should use the manufacturer's pin-description table and electrical-characteristics tables when assigning input, output, power, and compensation connections. Typical circuit roles include precision signal amplification, active filtering, sensor-signal conditioning, feedback amplification, and low-level analog processing. Its 14MHz bandwidth can be especially useful when filtering or feedback behavior must remain effective above audio-band frequencies, while the 7V/us slew rate helps preserve large-signal response when operating at higher frequencies. For implementation, preserve the manufacturer's recommended bypass and feedback-component choices, account for input and output voltage limits, and evaluate stability with the intended source impedance and load. Because an 8-lead SOIC has limited routing area, decoupling capacitors should be placed close to the power pins and sensitive input routes should be kept away from high-current switching nodes. This product page organizes the key operating characteristics, package considerations, application guidance, comparison fields, and replacement criteria for the LT1211IS8. It is intended to help engineers distinguish true pin-compatible substitutions from merely similar dual amplifiers and to evaluate the part against the specific bandwidth, slew-rate, supply, and package requirements of an analog signal chain.

RFQ Contact
LT1212IS - 14MHz Precision Quad Op Amp | Analog Devices
LT1212IS

LT1212IS - 14MHz Precision Quad Op Amp | Analog Devices

The Analog Devices LT1212IS is a four-channel precision operational amplifier with a typical gain-bandwidth product of 14 MHz, a typical slew rate of 7 V/us, and a 16-SO surface-mount package. Designed for single-supply operation, the LT1212 combines four amplifiers in one package for signal-conditioning, filtering, instrumentation, and control applications where channel count, precision, and dynamic performance are important. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. Within the broader semiconductor hierarchy, the LT1212 belongs to the precision operational amplifier class, a type of analog amplifier used for closed-loop signal conditioning. Its quad configuration reduces package count and provides four identical amplifier channels for systems requiring several independent analog functions. Key performance features include a 14 MHz typical gain-bandwidth product and a 7 V/us typical slew rate. According to the Analog Devices datasheet, fast settling reaches 0.01% after a 2 V step in approximately 900 ns and 1 mV after a 10 V step in approximately 2.2 us. These characteristics support accurate amplification of higher-frequency signals while preserving useful large-signal behavior in precision analog circuits. The LT1212 is the quad counterpart of the LT1211 dual amplifier. Its high-frequency performance allows a single amplifier type to cover functions that would otherwise require several separate precision op amps. The device is specified for single-supply operation, making it applicable to systems where the signal and supply rails must remain close to ground. Exact input-offset voltage, input-bias-current, common-mode range, supply range, noise, and temperature limits must be confirmed from the manufacturer datasheet before final circuit sizing. Typical uses include active low-pass filters, current-to-voltage conversion, sensor signal conditioning, sample-and-hold amplifier stages, audio preamplification, and instrumentation buffers. The LT1212IS is particularly useful when four channels can share common supply and ground connections, reducing board area compared with four individual single-amplifier packages. Designers should verify input common-mode voltage, output swing, supply voltage, stability, and load-driving limits against the operating conditions of the target circuit. Decoupling capacitors should be placed close to the power pins, and unused amplifier inputs should be configured according to the manufacturer recommendations to avoid offset errors and unnecessary output saturation. This page organizes the LT1212IS specifications, sourcing questions, application guidance, package details, and verified design considerations. It also distinguishes true pin-compatible replacements from related LT1212 family options, helping engineers identify when an alternative can preserve the existing 16-SO footprint and when a package or electrical difference requires PCB changes.

RFQ Contact
LT1213CS8 - 28MHz Dual Precision Op Amp | Analog Devices
LT1213CS8

LT1213CS8 - 28MHz Dual Precision Op Amp | Analog Devices

The Analog Devices LT1213CS8 is a dual, single-supply precision operational amplifier with a 28 MHz gain-bandwidth product, a 12 V/us slew rate, and an 8-lead SOIC package. Two independent amplifier channels are integrated into one package, allowing compact dual-stage, differential, or multi-signal conditioning designs. Its 500 ns typical settling time for a 2 V step and 1.1 us typical settling time for a 10 V step support accurate response to rapidly changing analog signals. A precision operational amplifier is a voltage-feedback amplifier designed to provide high open-loop gain, low offset error, and accurate signal amplification around a defined reference point. The LT1213 belongs to the operational-amplifier hierarchy, combining precision DC behavior with wide bandwidth and fast slew capability. It is therefore positioned between general-purpose amplifiers and specialized high-speed amplifiers rather than being limited to slow precision-only applications. The LT1213's principal performance characteristics include a 28 MHz typical gain-bandwidth product, 12 V/us typical slew rate, and fast settling performance. These figures indicate that the device can provide useful closed-loop bandwidth well above audio frequencies while also preserving the low DC-error characteristics expected from a precision amplifier. The Analog Devices product description specifically identifies the LT1213 as a single-supply precision op amp, while the LT1214 is the quad version of the same amplifier family. The LT1213 uses conventional voltage-feedback operation, making its implementation compatible with standard inverting, non-inverting, summing, and difference-amplifier topologies. Its combination of speed and precision is valuable when a signal requires both accurate DC-level control and rapid transitions, such as active filtering, signal conditioning, data acquisition, and feedback control. The two-channel configuration also reduces package count when an application needs matched functional stages rather than two unrelated amplifiers. Typical uses include precision active filters, low-level sensor signal conditioning, instrumentation buffering, servo or feedback loops, and dual-channel analog processing. Its 28 MHz bandwidth provides margin for higher-frequency closed-loop operation, while the 12 V/us slew rate limits large-signal distortion in fast transient paths. Designers should still verify output swing, input range, supply limits, and stability against the manufacturer datasheet for the exact operating conditions. Layout should keep input and feedback traces short, place compensation and decoupling components close to the associated pins, and avoid routing sensitive inputs beside high-current switching nodes. Because the CS suffix identifies a temperature-grade variant while the 8-SO package constrains board area, PCB footprint selection and thermal verification should occur together. The manufacturer datasheet and pin-description table remain the controlling references for electrical limits and package details. This product page combines the manufacturer-defined 28 MHz bandwidth and 12 V/us slew rate with ordering distinctions, package information, application guidance, and engineering-focused replacement analysis. It highlights where the LT1213CS8 is suitable, which electrical details still require confirmation, and how engineers should evaluate a replacement without changing the surrounding precision signal-chain design.

RFQ Contact
LT1214CS - 28MHz 12V/us Quad Precision Op Amp | Analog Devices
LT1214CS

LT1214CS - 28MHz 12V/us Quad Precision Op Amp | Analog Devices

Analog Devices LT1214CS is a four-amplifier precision operational-amplifier IC with a 28 MHz typical gain-bandwidth product, 12 V/us typical slew rate, and a 16-lead SOIC package. Designed for single-supply operation, the device combines four general-purpose amplifiers in one package and supports precision signal conditioning, filtering, and gain-stage applications. The verified manufacturer material identifies LT1214CS as the quad version of the LT1213/LT1214 precision amplifier family. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The operational-amplifier category belongs to the broader analog-amplifier hierarchy and supports DC-precision signal conditioning, instrumentation, buffering, active filtering, and closed-loop control. In a feedback network, the LT1214CS can set closed-loop gain and signal polarity while using its 28 MHz bandwidth and 12 V/us slew rate to reproduce changing waveforms with relatively low delay. The verified data identifies a typical 28 MHz gain-bandwidth product and 12 V/us slew rate. It also lists fast settling to 200 uV within 500 ns after a 2 V step and to 1 mV within 1.1 us after a 10 V step. These figures make the four internal amplifiers useful when multiple channels must process comparable signals, particularly in active filters, sensor interfaces, audio paths, and control systems. The DC-precision positioning also helps reduce external trim requirements in systems where offset and drift must be controlled. Architecturally, the LT1214CS places four amplifiers in one 16-lead SOIC rather than requiring four separate packages. A typical application uses each amplifier for a distinct function, such as instrumentation amplification, active filtering, output buffering, or error amplification. The package consolidates routing over one PCB footprint while still providing independent amplifier channels. Because the verified snippets do not provide the complete electrical tables, exact input-offset voltage, input-bias current, noise density, supply-current, and common-mode-range values should be confirmed in the manufacturer datasheet before final design release. Typical uses include multichannel sensor conditioning, precision active filters, audio signal paths, instrumentation front ends, and general-purpose control loops. The quad organization is especially useful when several signals must be amplified consistently within one instrument, converter, or monitoring system. The 16-SO package allows a conventional surface-mount layout, although careful grounding and decoupling remain necessary for stable high-gain operation. The principal design consideration is to verify rail-to-rail behavior, common-mode limits, output swing, and stability requirements for the specific operating conditions. Input and output capacitors should be placed close to their associated pins, sensitive analog traces should avoid switching-current paths, and unused amplifier channels should be configured according to the manufacturer recommendations rather than left floating. This page combines verified manufacturer and distributor information with a parameter-focused application guide, sourcing guidance, and explicit data gaps. It also distinguishes the lead-free LT1214CS#PBF ordering designation from the base LT1214CS MPN instead of treating a packaging-ordering variant as a separate drop-in alternative.

RFQ Contact
LT1215CS8 - 23MHz Dual Precision Op Amp | Analog Devices
LT1215CS8

LT1215CS8 - 23MHz Dual Precision Op Amp | Analog Devices

Analog Devices LT1215CS8 is a dual, single-supply precision operational amplifier with a 23 MHz gain-bandwidth product and a 50 V/µs slew rate, housed in an 8-pin SOIC package. The LT1215 family combines two amplifier channels with the DC precision required for instrumentation, signal-conditioning, and active-filter designs. An operational amplifier, or op amp, is a high-gain differential-input amplifier whose feedback network defines its closed-loop behavior. Within the amplifier hierarchy, the LT1215CS8 is a precision operational amplifier used for low-level signal amplification, impedance buffering, filtering, and feedback control. Its dual-channel configuration provides two amplifiers in one compact surface-mount package while reducing the number of components required on a circuit board. The principal highlighted performance characteristics of the LT1215 are its 23 MHz gain-bandwidth product and 50 V/µs slew rate. These values support comparatively fast closed-loop operation and make the device suitable for signal paths that require both bandwidth and slew-rate capability. The manufacturer also describes the LT1215 and LT1216 family as single-supply precision amplifiers whose DC precision eliminates external trimming in most systems. The LT1215 is a dual amplifier, whereas the related LT1216 is a quad version of the same amplifier family. This distinction is important when selecting a package and pin count: the LT1215CS8 uses an 8-pin SOIC, while a quad implementation requires a different package and pin assignment. Design engineers should therefore verify the complete pin description table in the manufacturer datasheet before assigning amplifier inputs, outputs, supply rails, and exposed connections. Typical uses include precision instrumentation, low-level sensor-signal conditioning, active filters, sample-and-hold circuitry, and general-purpose analog signal processing. The two channels can be used together for cascaded stages, differential signal conditioning, or independent amplifier functions. Input and output impedance requirements, allowable common-mode range, noise, offset, and stability behavior should be checked against the application signal range before finalizing the circuit. For single-supply operation, the circuit must provide a suitable bypass strategy around the power pins and maintain the amplifier within its common-mode input range. Decoupling capacitors should be placed close to the device, and sensitive inputs should use layouts that minimize leakage from high-impedance nodes. Output loading and feedback-component selection also affect achievable bandwidth and closed-loop response. This product page combines the manufacturer’s device description with package information, engineering application guidance, selection criteria, and a structured view of the LT1215CS8’s role in precision analog design. It also distinguishes the dual LT1215 from the quad LT1216 and identifies where the manufacturer datasheet is needed for final pin-level implementation decisions.

RFQ Contact