Products (44,000+)

LT685CN - 5.5ns High-Speed ECL Comparator | Analog Devices
LT685CN

LT685CN - 5.5ns High-Speed ECL Comparator | Analog Devices

The Analog Devices LT685CN is an ultrafast high-speed comparator with a typical propagation delay of 5.5 ns, differential inputs, complementary ECL-compatible outputs, and a 16-pin PDIP package. It is designed for demanding analog-to-digital signal-processing and pulse-timing systems where fast decision time and direct transmission-line drive are important. The device also includes an output latch and an external hysteresis-control function. A comparator is an analog signal-processing semiconductor that evaluates two input voltages and produces a logic output indicating which input is higher. The LT685 belongs to the comparator hierarchy, where its differential inputs, complementary outputs, and ECL interface place it between general-purpose logic-level comparators and high-speed timing components used in instrumentation, communications, and data acquisition. The main features of the LT685CN include its 5.5 ns typical propagation delay, complementary ECL outputs, 50-ohm transmission-line drive capability, low input offset, output latch capability, and compatibility with the AM685 family. Its differential input structure supports balanced signal comparison, while the complementary outputs allow direct use in systems requiring both true and inverted decisions. The latch function can hold the comparator state for applications that need sampled or stored decisions rather than continuous tracking. The LT685 uses an older high-speed ECL-compatible architecture intended for short propagation-delay operation and controlled point-to-point interconnects. Its output current capability is specified for driving transmission lines terminated in 50 ohms, making board-level routing and termination more important than with ordinary CMOS or TTL comparators. Differential inputs can also reduce sensitivity to common-mode noise when the surrounding analog signal path is properly laid out and referenced. Typical applications include pulse-width and pulse-height discrimination, high-speed threshold detection, ECL interface circuits, analog-to-digital front ends, communications equipment, laboratory instrumentation, and timing recovery systems. The 16-pin PDIP package is through-hole and suitable for legacy or prototype boards where the comparator must be inserted or socketed rather than mounted in a compact surface-mount assembly. When designing a circuit around the LT685CN, verify input common-mode range, output termination, supply requirements, latch timing, and the required propagation-delay margin. Keep high-speed traces short, use controlled impedance where practical, and terminate ECL-compatible outputs according to the system’s transmission-line topology. The available verified data does not establish exact input common-mode limits, supply-current values, pin-level timing, or package temperature limits. This product record combines the verified LT685 and LT685CN manufacturer information, distributor availability references, and cross-reference search results with practical guidance for high-speed comparator implementation. It also distinguishes documented drop-in alternatives from package or functional similarities so that engineers can make a replacement decision based on actual pin and parameter evidence.

RFQ Contact
LTC1049CH Zero-Drift Operational Amplifier | Analog Devices
LTC1049CH

LTC1049CH Zero-Drift Operational Amplifier | Analog Devices

The Analog Devices LTC1049CH is a low-power, zero-drift operational amplifier with internal capacitors, offered in an 8-terminal round TO-5 package with wire-form leads. The device is intended for instrumentation, sensor signal conditioning, and precision analog applications where low offset voltage and low drift are more important than high bandwidth. It uses chopper or zero-drift techniques to reduce errors that normally change with time and temperature. A zero-drift operational amplifier is a precision amplifier optimized for very low input-offset voltage and low drift over time. Unlike conventional amplifier designs whose offset error moves with temperature and aging, a zero-drift amplifier periodically corrects its own input error. The result is useful for bridge sensors, strain gauges, thermocouples, current measurements, and other applications where a small DC error can dominate the measurement result. The LTC1049 also includes internal capacitors, simplifying common application circuits. The Analog Devices product information identifies the LTC1049 as a production low-power zero-drrift operational amplifier. The manufacturer describes versions in an 8-pin plastic dual-in-line package and an 8-pin SO package, while the LTC1049CH order code is identified as an 8-terminal TO-5 package with wire leads and industrial temperature grade. The package also includes an exposed metal case or lead configuration intended to support thermal conduction and, depending on the assembly, mechanical mounting. Zero-drift architectures introduce practical considerations that differ from ordinary amplifier behavior. Their input errors are exceptionally small, but chopping can create ripple-related artifacts at internal correction frequencies. Circuit designers should account for the datasheet's input-noise and frequency-response characteristics, connect the specified internal-capacitor pins according to the manufacturer diagram, and provide stable supply bypassing. Layout should keep sensitive input traces short and avoid routing them beside switching nodes or high-current return paths. Typical uses include low-level sensor amplification, portable measurement systems, process-control instrumentation, battery-powered equipment, and precision data acquisition. In a bridge or thermocouple circuit, the low drift helps preserve calibration accuracy over time, while the internal capacitors can reduce the number of external components required for stable operation. The amplifier should still be evaluated against the full signal range, output swing, noise bandwidth, supply voltage, and common-mode limits of the intended design. For a new layout, use the pin-description table in the Analog Devices LTC1049 data sheet when assigning PCB tracks, and preserve the recommended grounding and bypass-capacitor connections. Do not substitute a different package or pinout without confirming the exact ordering code and electrical behavior. This page combines the manufacturer product information with engineering guidance for selecting, laying out, and sourcing the LTC1049CH. For replacement decisions, compare the exact package, lead arrangement, input-offset behavior, supply range, output swing, and capacitor requirements. A similar amplifier function alone does not establish a drop-in replacement because the physical mounting and pinout of the 8-lead TO-5 package are central to PCB compatibility.

RFQ Contact
LTC1050CP Precision Zero-Drift Operational Amplifier | Analog Devices
LTC1050CP

LTC1050CP Precision Zero-Drift Operational Amplifier | Analog Devices

The Analog Devices LTC1050CP is a precision zero-drift operational amplifier with two internal sample-and-hold capacitors, offered in the LTC1050CP commercial-temperature package configuration. This low-cost op amp combines a chopper-stabilized architecture with on-chip capacitors, reducing the external components normally associated with zero-drift amplifiers. Its primary applications include precision current sensing, low-level signal amplification, instrumentation, sensor interfaces, and feedback loops requiring low offset voltage and stable DC performance. A zero-drift operational amplifier is a precision amplifier designed to minimize input offset voltage drift over time and temperature. It belongs to the operational-amplifier hierarchy, which includes instrumentation, rail-to-rail, precision, and comparator circuits. Unlike a conventional amplifier whose input offset can move as temperature changes, the LTC1050 uses periodic zero-drift correction to reduce low-frequency offset movement. This makes it useful when a small sensor voltage must be amplified without introducing a large error over the measurement interval. The LTC1050 family integrates the two sample-and-hold capacitors normally placed outside many chopper-stabilized amplifiers. Removing those external capacitors simplifies PCB layout and reduces the number of components requiring assembly and inspection. According to the manufacturer datasheet, this integration allows the amplifier to offer improved combined DC and AC performance compared with conventional implementations that require external chopping capacitors. The result is a compact solution for precision analog front ends. The zero-drift architecture is particularly effective for signals concentrated near DC, including strain-gauge outputs, pressure-sensor signals, thermocouple interfaces, and low-level error amplifiers. Chopper-related frequency components remain relevant when the closed-loop bandwidth approaches the amplifier's chopper frequency, so the complete signal chain must be checked for noise at those harmonics. Input and output filtering should be selected according to the required measurement bandwidth rather than simply maximizing bandwidth. Typical uses include bridge-sensor amplification, precision current measurement, low-voltage sensor conditioning, instrumentation inputs, and active low-pass filters. The integrated sampling capacitors make it particularly attractive where board area or assembly complexity is more important than high-frequency performance. In feedback applications, designers should include adequate phase margin and verify settling after chopping transitions before treating the amplifier as a conventional wideband op amp. The primary design consideration is to preserve the zero-drift benefit without introducing excessive noise. Decoupling capacitors should be placed close to the supply pins, sensitive input traces should be kept short, and the output should avoid driving long capacitive loads unless stability has been confirmed. The datasheet's application guidance and test conditions should also be used to establish acceptable offset, noise, bias-current, and common-mode limits for the intended application. This product page combines the LTC1050CP identity, manufacturer documentation references, engineering applications, design guidance, and a traceable list of authoritative sources. It also highlights where circuit-level validation is necessary, particularly for chopping noise, stability, common-mode range, supply selection, and any proposed direct replacement.

RFQ Contact
LTC1064CJ - Quad Universal Filter Building Block | Analog Devices
LTC1064CJ

LTC1064CJ - Quad Universal Filter Building Block | Analog Devices

The Analog Devices LTC1064CJ is a low-noise, fast, quad universal switched-capacitor filter building block rated for a 140 kHz switched frequency and supplied in a 24-pin CDIP package. It combines four high-speed filter sections with a universal architecture capable of implementing low-pass, high-pass, band-pass, band-stop, and other second-order responses. A switched-capacitor active filter is an analog filter that uses periodically switched capacitors and an external clock to create frequency-dependent behavior equivalent to resistive-capacitive networks. The LTC1064 belongs to the active-filter category, which is part of the broader signal-conditioning IC hierarchy for analog and mixed-signal systems. Its four building blocks can implement multiple second-order filter functions when paired with an external clock and three to five external resistors. The four independently usable sections provide a practical way to build multichannel signal conditioning without requiring four separate monolithic filter packages. Low noise is valuable when processing weak sensor, audio, communications, or instrumentation signals, while the fast 140 kHz switching capability allows the device to cover a broad range of timing and frequency-response requirements. An external clock gives the system designer control over the switched-capacitor operating rate and filter response. Each building block uses switched-capacitor techniques to establish its frequency response, but practical performance also depends on the external clock, resistor tolerances, capacitor selection, grounding, and the bandwidth of the signals being filtered. Because the architecture is universal, component values and topology determine whether a section performs low-pass, high-pass, band-pass, band-stop, or another supported second-order function. The four sections can also be combined for higher-order filtering when one section alone does not provide the required attenuation or roll-off. Typical uses include antialiasing before switched-capacitor data converters, low-noise analog measurement chains, audio signal conditioning, communication-channel filtering, waveform shaping, and general-purpose active filtering. In a multichannel system, identical clocking and closely matched external networks can produce consistent channel behavior, although each section still requires careful component selection and layout. For reliable implementation, follow the manufacturer datasheet for clock levels, resistor networks, bypass capacitance, grounding, and allowable signal amplitudes. Keep clock routing away from sensitive analog inputs, use a low-noise ground reference, and place filter components close to their associated pins. Validate gain, cutoff frequency, and stopband attenuation with the actual clock and source impedance rather than relying only on nominal calculations. This page combines the manufacturer product information, package and operating characteristics, practical filter-design guidance, sourcing information, and verified drop-in replacement findings. It is designed to help engineers identify the correct LTC1064CJ ordering code, plan a working filter, and assess replacement options without treating merely similar filter ICs as PCB-compatible substitutes.

RFQ Contact
LTC1067IGN - Dual Switched-Cap Filter 20kHz | Analog Devices
LTC1067IGN

LTC1067IGN - Dual Switched-Cap Filter 20kHz | Analog Devices

The Analog Devices LTC1067IGN is a rail-to-rail, very low noise universal dual switched-capacitor filter building block that delivers two independent 2nd-order filter sections with cutoff frequencies up to 20 kHz in a 16-pin SSOP (narrow) package. Each filter section uses external resistors and the internal switched-capacitor architecture to implement low-pass, band-pass, notch, and all-pass responses. The device targets signal-conditioning applications where small footprint, low noise, and high dynamic range are mandatory. What is a switched-capacitor filter? A switched-capacitor filter is an active filter topology that emulates a resistor using a capacitor switched at a clock frequency, allowing precise, monolithic filter implementations without external precision capacitors. Within the broader IC taxonomy, switched-capacitor filters fall under active filters -> analog filters -> signal conditioning -> analog ICs -> semiconductors. They are preferred over continuous-time active filters for applications requiring tight frequency accuracy relative to an external clock. Key features include a clock-to-cutoff ratio of 100:1 (the LTC1067-50 variant uses 50:1), rail-to-rail input and output swing that maximizes dynamic range on low-voltage supplies, 60 dB signal-to-noise ratio, and a low noise floor suitable for instrumentation-grade signal chains. Each second-order block uses five external resistors, allowing independent configuration as a low-pass, high-pass, band-pass, or notch stage. Two blocks can be cascaded externally to build a 4th-order filter. The architecture is built on Analog Devices' precision switched-capacitor technology with CMOS analog switches and on-chip clock generation. The clock input accepts a TTL or CMOS external source, and the internal master clock divider sets the filter cutoff, simplifying design-in when synchronization to a system clock is required. The dual-block topology also enables independent filtering of two channels, such as stereo audio or dual-axis sensor signals, in a single IC. Typical applications include antialiasing filters for 16-bit ADCs, smoothing filters for DAC outputs, dual-channel audio crossover networks, instrumentation low-pass filters in data acquisition systems, and ultrasonic transducer front-end filtering in medical imaging. The wide dynamic range makes the LTC1067IGN particularly attractive when the upstream signal already spans most of the supply range. When designing with this part, plan clock-to-cutoff ratio carefully: the cutoff frequency equals fCLK/100 (or /50 for the -50 variant). A stable, low-jitter clock is essential - phase noise on the clock translates directly into passband distortion. Keep clock traces short and away from analog signal traces to prevent coupling. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet's typical application circuits.

RFQ Contact
LTC1094CJ - 8-Ch 10-Bit Serial DAS | Analog Devices
LTC1094CJ

LTC1094CJ - 8-Ch 10-Bit Serial DAS | Analog Devices

Analog Devices LTC1094CJ is an 8-channel, 10-bit serial I/O data acquisition system in a 20-pin CERDIP package. The device combines a 10-bit switched-capacitor successive-approximation ADC core with software-configurable analog multiplexing, allowing a microcontroller or other serial host to acquire multiple analog channels through a compact mixed-signal interface. Its industrial temperature grade and through-hole construction suit instrumentation and embedded control systems where reliable PCB assembly and broad operating-temperature performance are important. A data acquisition system, or DAS, is an integrated mixed-signal semiconductor that combines analog multiplexing, conversion, and a digital control or serial interface. In the hierarchy of electronic components, the LTC1094CJ belongs to the ADC family, which forms part of the broader data-converter and signal-processing category. The 10-bit ADC provides 1,024 representable digital codes, making it appropriate for monitoring applications that require moderate measurement resolution rather than high-precision laboratory conversion. The key features of the LTC1094CJ include eight multiplexed input channels, 10-bit conversion resolution, serial I/O, and a selectable bipolar or unipolar input configuration. The switched-capacitor successive-approximation core allows the converter to combine compact implementation with practical acquisition performance. Because the multiplexer is software-configurable, a host controller can select among the available analog inputs and configure operating modes through the serial control interface. The LTC1094 family also includes 1-, 2-, 6-, and 8-channel configurations, while the LTC1094CJ specifically provides the 8-channel option. This distinction matters when comparing the CJ suffix with other family members. The CJ version is identified as an industrial-grade, 20-terminal, through-hole ceramic DIP rather than a surface-mount package. Its 20-CERDIP format supports conventional through-hole PCB assembly and is suitable for designs that favor robust mechanical attachment over compact board area. Typical uses include industrial process monitoring, transducer signal acquisition, laboratory measurement interfaces, environmental sensing, and embedded data-logging systems. In a multi-sensor installation, the eight-channel multiplexer can reduce the number of physical analog input connections needed by a microcontroller while retaining a common serial command and data path. The host system determines the channel sequence, acquisition timing, and interpretation of the resulting 10-bit values. A key design consideration is the analog front-end. Sensor outputs must remain within the selected bipolar or unipolar input range, and the source impedance seen by each muxed input can affect conversion accuracy and settling time. Layout should minimize trace lengths between sensors, protection components, and the LTC1094CJ while separating digital serial activity from sensitive analog nodes. Grounding, reference decoupling, and acquisition timing should be evaluated together rather than optimized independently. This product page combines the manufacturer product information, distributor identification, package details, and cross-reference findings into an engineering-focused description. It also identifies the verified drop-in alternative, documents replacement and selection questions, and highlights practical considerations for implementing an eight-channel serial data acquisition front end.

RFQ Contact
LTC1099CN#30369 - 8-Bit 2.5µs ADC w/ S/H | Analog Devices | DIP-20
LTC1099CN#30369

LTC1099CN#30369 - 8-Bit 2.5µs ADC w/ S/H | Analog Devices | DIP-20

The Analog Devices LTC1099CN#30369 is an 8-bit, 2.5 µs analog-to-digital converter (ADC) with an integrated sample-and-hold amplifier, housed in a 20-pin PDIP (N-20) through-hole package. It offers one input channel with a flash-style conversion architecture, supports full Nyquist-rate sampling, and is qualified for the commercial 0 °C to 70 °C operating range. The part is supplied in a 20-PDIP package with an input count of 1 and a flash converter topology per the manufacturer's product family specification. What is a flash ADC? A flash ADC is a parallel architecture where every possible quantization level is realized by a dedicated comparator bank feeding an encoder; conversion happens in a single step so latency is essentially one comparator delay, making flash ADCs the fastest ADC topology but resolution-limited by comparator count. Within the converter hierarchy, the LTC1099 sits between SAR (successive approximation) and full flash converters, using a sub-ranging / flash-front-end plus internal sample-and-hold to digitize high-bandwidth analog signals up to the full Nyquist rate. As a data-conversion IC, it belongs to the broader category of data acquisition > analog-to-digital converter > monolithic 8-bit ADC. Key features include a 2.5 µs typical conversion time (corresponding to 156 kHz 5V p-p input bandwidth), a built-in track-and-hold, microprocessor-compatible interface for direct connection to parallel-bus microcontrollers, single +5 V supply operation, and a flash-derived architecture. The integrated S/H allows the converter to handle fast-step inputs without requiring an external buffer, simplifying front-end design. The LTC1099 uses a sub-ranging flash architecture with internal reference generation and digital error correction. The integrated sample-and-hold sits at the analog front end and guarantees accurate acquisition of fast transient signals at the full Nyquist rate, which a discrete ADC + external amplifier combination often cannot match for input slew without careful layout. Typical applications include waveform digitizers, digital oscilloscope front-ends, video bandwidth digitizing up to 156 kHz, data-acquisition boards for industrial instrumentation, and process-control signal conditioning. It also serves in VCO/PLL feedback readback, ultrasound return-signal sampling, and any design requiring fast 8-bit throughput in a simple parallel microprocessor interface. When designing with the LTC1099, ensure clean analog and digital grounds (separated at the device pin) and place the supply bypass capacitor as close as possible to the VCC pin. The internal S/H drives input capacitance; source-impedance and bandwidth trade-offs should be evaluated when feeding the analog input directly from a sensor or filter. This page synthesizes distributor pricing, drop-in equivalents, and design notes not present in the bare manufacturer datasheet, including intent-specific FAQs and a comparison table for engineers migrating from earlier 8-bit ADCs.

RFQ Contact
LTC1164CJ - Low-Power Quad Switched-Capacitor Filter | Analog Devices
LTC1164CJ

LTC1164CJ - Low-Power Quad Switched-Capacitor Filter | Analog Devices

The Analog Devices LTC1164CJ is a low-power, low-noise quad switched-capacitor universal filter containing four independent second-order filter building blocks, each operating over a 20 kHz cutoff range, in a 24-pin ceramic DIP package. Each building block typically consumes 850 µA, and the device supports dual supply voltages of ±3 V or ±5 V within an operating range of ±2.37 V to ±8 V. A switched-capacitor active filter is an analog signal-processing IC that uses clocked internal capacitors and switches to implement frequency-selective behavior. In the signal-chain hierarchy, the LTC1164 belongs to the active-filter category, which sits within analog integrated circuits and signal-conditioning systems. Instead of requiring a separate resistor, capacitor, and op-amp network for each second-order section, it provides four programmable building blocks on one integrated circuit. The four second-order sections can implement low-pass, high-pass, band-pass, band-stop, and notch responses through external resistor and capacitor selection. Low-noise operation makes the device useful when filtering small signals before amplification or digitization. Its low-power architecture is also appropriate for portable instrumentation, compact data-acquisition systems, audio test equipment, and embedded measurement products where four filter channels must be accommodated without using four separate discrete filter networks. The internal switched-capacitor architecture provides the main functional benefit of accurate, repeatable filter behavior tied to external clock and component selections. The characteristic trade-off is that switched-capacitor filters introduce clock-related noise and require a clean clock signal. Component tolerances also determine how closely the implemented cutoff, gain, and response shape match their intended values, so resistor and capacitor selection remains an important part of the filter design. LTC1164CJ applications include anti-alias filtering ahead of analog-to-digital converters, noise rejection in low-level sensor interfaces, audio and communication signal conditioning, laboratory measurement systems, and programmable industrial test equipment. The 24-pin ceramic DIP package supports through-hole PCB construction and legacy instrumentation platforms that require a conventional dual-in-line footprint. When laying out a circuit using the LTC1164CJ, keep clock and sensitive filter-node traces away from switching power paths, use a low-noise ground strategy, and place external clock and timing components close to their associated pins. Verify the selected component tolerances against the required cutoff frequency and response shape rather than relying only on nominal values. This product page combines package, function, filter-class, supply-range, and ordering information with practical selection guidance. It also distinguishes verified production and ordering facts from package details and application advice that must be confirmed against the manufacturer datasheet before a new design is released.

RFQ Contact
LTC1283CJ - 10-Bit 8-Channel ADC | Analog Devices
LTC1283CJ

LTC1283CJ - 10-Bit 8-Channel ADC | Analog Devices

Analog Devices LTC1283CJ is a 3 V data acquisition IC containing a serial-interface, successive-approximation analog-to-digital converter with 10-bit unipolar or 9-bit-plus-sign bipolar resolution and an 8-channel input multiplexer. The device is offered in a ceramic 20-pin DIP package and is specified for the commercial temperature range. A data acquisition system converts real-world analog voltages into digital values for measurement, control, or display. Within the ADC category, the LTC1283 integrates a successive-approximation converter, an analog input multiplexer, and an on-chip sample-and-hold circuit. Its serial interface reduces the number of signal connections required between the converter and a controller while preserving dedicated analog measurement capability. Key features include an 8-channel analog multiplexer that can be configured for single-ended inputs, differential inputs, or combinations of both. The converter supports 10-bit unipolar and 9-bit plus sign bipolar operating modes. LTCMOS switched-capacitor technology performs the conversion, while the integrated sample-and-hold circuit captures the input voltage before conversion. A 3 V supply and a 20-pin ceramic DIP package support compact through-hole instrumentation layouts. The multiplexer is the central architectural feature for multi-sensor systems. Instead of dedicating one converter to every input, it routes selected channels to the shared converter and sample-and-hold circuit. Differential operation can reduce the influence of common-mode voltage on measurements, while single-ended operation simplifies connections for sensors with one signal output and a shared reference. Serial output supports economical connection to a microcontroller or embedded controller. Typical uses include industrial process measurement, multichannel sensor acquisition, battery-powered instrumentation, and embedded control systems that need several analog inputs but only moderate conversion resolution. The LTC1283CJ is also appropriate for prototypes and legacy equipment requiring a through-hole ceramic DIP footprint, especially where board area is less important than straightforward assembly and serviceability. Design around the exact input ranges, acquisition timing, reference requirements, and serial protocol listed in the Analog Devices LTC1283 datasheet. Confirm signal source impedance, acquisition time, reference stability, grounding, and digital-interface levels before finalizing the analog front end. Use the manufacturer's pin-description table and application guidance when assigning tracks and guarding inputs. This page organizes the LTC1283CJ's converter architecture, multiplexing capabilities, package details, sourcing path, and engineering considerations into a practical selection reference. It also separates verified device facts from replacement and lifecycle decisions that require direct manufacturer confirmation.

RFQ Contact
LTC1318CN - Single 5V RS232/RS422 Transceiver | Analog Devices
LTC1318CN

LTC1318CN - Single 5V RS232/RS422 Transceiver | Analog Devices

The Analog Devices LTC1318CN is a single 5V RS232/RS422/AppleTalk DCE transceiver with an integrated charge pump, two RS232 drivers, one differential RS422 driver, and dedicated RS232 receive capability in a 24-PDIP package. Its charge pump generates a ±8V supply for true RS232 output swings and requires four external 0.1µF capacitors. The LTC1318CN is designed for the DCE, or peripheral side, of an interface link. An RS232/RS422 transceiver is an interface IC that converts logic-level signals between a host or controller and a wired communication link. RS232 is a single-ended, unbalanced interface commonly associated with computer serial ports, while RS422 uses differential signaling for improved noise immunity and longer-distance transmission. The AppleTalk designation identifies another supported serial-interface application for the combined transceiver architecture. The principal feature of the LTC1318CN is its integrated on-board charge pump. This circuit develops the bipolar voltage needed for RS232 output levels without requiring a separate negative supply. The manufacturer datasheet specifies four external 0.1µF capacitors for the charge-pump function, allowing a compact implementation while retaining true RS232 output swings. The device operates from a single 5V supply, which simplifies connection to conventional digital logic. The transceiver combines two RS232 drivers, a differential RS422 driver, and a dedicated RS232 receiver. This mixed-signal arrangement supports equipment that must interface with both RS232 and RS422 links while minimizing the number of external interface components. The three-driver, three-receiver designation in distributor product listings reflects the number of available driver and receiver channels, while the DCE orientation determines how the transceiver is connected within the system. Typical uses include legacy peripheral interfaces, AppleTalk equipment, industrial data-collection equipment, computer serial-port adapters, and embedded systems that retain RS232 or RS422 connections. In these applications, the LTC1318CN can bridge low-voltage controller logic to externally biased RS232 signals or provide differential RS422 transmission. Its through-hole 24-PDIP format is also suitable for prototypes and legacy boards where leaded components remain easier to inspect, repair, or manually replace. Designers should preserve the charge-pump capacitor layout recommended in the manufacturer datasheet and provide adequate logic-level interfacing for every driver and receiver connection. PCB placement must keep charge-pump current loops compact, while RS232 and RS422 routes should avoid sources of severe electromagnetic interference. Because the product is listed as obsolete, new production designs should contact Analog Devices for a current replacement before committing to a long-life program. This page consolidates the functional description, interface requirements, package information, lifecycle status, and practical design considerations for engineers evaluating the LTC1318CN. It also distinguishes confirmed drop-in replacements from candidate parts whose electrical and pin compatibility still require formal validation.

RFQ Contact
LTC1338CG - 5V Low-Power RS-232 Transceiver | Analog Devices
LTC1338CG

LTC1338CG - 5V Low-Power RS-232 Transceiver | Analog Devices

Analog Devices LTC1338CG is a 5V low-power RS-232 transceiver with five drivers, three receivers, a 500 uA no-load supply current, and a 28-pin SSOP package. It operates from a single 5V supply, supports data rates up to 120 kbaud, and includes ESD protection rated to ±10 kV. Four 0.1 uF capacitors are sufficient for the charge-pump circuit, while shutdown mode reduces supply current to 0.2 uA. An RS-232 transceiver is an interface IC that converts logic-level signals between a host controller and RS-232 equipment. The LTC1338 belongs to the transceiver hierarchy, where a complete interface IC combines line drivers, receivers, charge-pump voltage conversion, and sometimes shutdown control. It is designed for compact serial-port equipment where low supply current, limited board area, and robust electrostatic protection are important. Five driver outputs support multiple RS-232 channels or control signals, while three receiver inputs support three incoming data or handshake signals. Three-state driver outputs allow the drivers to be disconnected when the bus direction changes. The 120 kbaud capability accommodates legacy communications, industrial controllers, service interfaces, and equipment-control links without requiring a separate external charge-pump supply. The single 5V architecture simplifies power-system design because the device generates the RS-232 bipolar levels internally. Its low 500 uA no-load supply current reduces standby demand, and the 0.2 uA shutdown current is valuable in portable or intermittently powered instruments. Driver outputs and receiver inputs withstand forced voltages down to −25V without damage, adding protection margin on externally accessible connectors. Typical uses include legacy serial-port adapters, programmable test equipment, industrial control panels, embedded service interfaces, and communication links between older RS-232 peripherals and modern controller boards. The 28-pin SSOP package supports surface-mount assembly but requires careful handling because the lead pitch is narrower than that of a standard SOIC. Designers should connect the four 0.1 uF charge-pump capacitors exactly as shown in the manufacturer application information, place them close to the associated pins, and provide adequate bypass capacitance at the supply pins. External protection should supplement the internal ±10 kV ESD rating when cables extend beyond the enclosure or connect to industrial environments. This page consolidates the device’s principal electrical characteristics, package information, application fit, and verified substitution status. The comparison and design notes emphasize the practical trade-offs that matter when replacing an RS-232 interface without changing the PCB footprint.

RFQ Contact
LTC1344CG - 6-Channel Software-Selectable Terminator | ADI
LTC1344CG

LTC1344CG - 6-Channel Software-Selectable Terminator | ADI

The Analog Devices LTC1344CG is a software-selectable cable terminator containing six independently configurable terminator channels in a 24-pin SSOP package. Each channel can be configured for an RS-422 V.11 load of 100 ohms minimum, a V.35 T-network load, or an open circuit for RS-232 V.28 and RS-423 V.10 transceivers that provide their own termination. The device also avoids loading the line with power off. A cable terminator is an interface-circuit component that establishes the impedance expected by a communication standard at the receiving end of a cable. For differential links, termination reduces reflected signals and helps maintain reliable data transfer. Multi-protocol systems can require different termination arrangements as the physical interface changes, so a fixed resistor network may not be suitable. The LTC1344CG places six configurable terminators in one package, reducing the number of discrete networks required for multiprotocol equipment. The manufacturer identifies six software-selectable multiprotocol cable terminators as the central feature of the LTC1344 family. Supported configurations include an RS-422 differential load, a V.35 T-network load, and an open state for transceivers incorporating their own termination. The power-off behavior is specifically useful because the terminator does not load the line when system power is absent. Exact control logic, supply limits, resistance values, and timing specifications should be taken from the manufacturer datasheet when designing the control interface. In a typical multiprotocol port, the LTC1344CG is placed near the line connector so that the selected termination is presented at the cable interface. The open setting allows RS-232 or RS-423 transceivers with integrated termination to remain in circuit, while the V.11 and V.35 modes provide the corresponding load for other protocols. Keeping the termination network close to the connector can reduce the length of unterminated transmission line, although signal routing, grounding, and the transceiver manufacturer's recommendations remain important. Typical uses include multiprotocol communications equipment, RS-232 port concentrators, V.35 network interfaces, and legacy data-communication systems where one connector must support several electrical standards. The LTC1344 can also be paired with the LTC1343 to form a complete software-selectable multiprotocol serial interface, as identified by the manufacturer product page. This pairing is particularly relevant when both transceiver selection and termination selection must be coordinated by the host. The principal design consideration is control sequencing. Determine the required protocol state before enabling the interface, and ensure software cannot leave an inappropriate termination connected during reset or power transitions. Also verify the exact channel mapping, logic levels, supply requirements, and package dimensions against the manufacturer documentation before laying out a PCB or assigning control pins. This product page organizes the confirmed LTC1344CG functions, protocol configurations, package information, sourcing paths, and application guidance for engineers evaluating multiprotocol cable termination. It also distinguishes the confirmed capabilities of the LTC1344 family from detailed electrical values that must be confirmed in the manufacturer datasheet before a production design is released.

RFQ Contact
LTC1350CG - 120 kbaud RS-562 Transceiver | Analog Devices
LTC1350CG

LTC1350CG - 120 kbaud RS-562 Transceiver | Analog Devices

Analog Devices LTC1350CG is a 3-driver, 5-receiver RS-562 line transceiver rated for data rates up to 120 kbaud and operation from a 3.3 V low-power supply. The device is offered in a 28-terminal commercial-grade SSOP package with gull-wing leads. According to the Analog Devices manufacturer product page, it complies with the applicable EIA/TIA-562 data-rate and overvoltage requirements and can drive a 1000 pF load through a 3 kΩ network. An RS-562 transceiver is a bidirectional interface IC that combines differential line-driver and line-receiver functions in one package. In the broader semiconductor hierarchy, it belongs to the interface-IC family, where transceivers sit between digital logic and physical communication lines. Unlike single-ended RS-232 equipment, RS-562 is designed for balanced, point-to-point connections and reduced ground-reference sensitivity. The LTC1350CG therefore serves as the physical-layer interface between a data-processing system and a balanced cable. The three drivers support independent transmit channels, while the five receivers provide five receive channels. Its maximum operating data rate of 120 kbaud makes it appropriate for moderate-speed control, instrumentation, and industrial data links rather than high-speed Ethernet or video transmission. Operation from a 3.3 V supply also allows it to interface with modern 3.3 V logic systems. Commercial-grade temperature classification makes the CG suffix relevant for room-temperature industrial and commercial equipment. The receiver architecture provides the physical-layer interface needed for balanced data transfer, while the multiple driver and receiver channels reduce the number of separate interface packages required in multi-channel equipment. Designers should account for the specified 1000 pF and 3 kΩ load condition when evaluating cable length, termination, topology, and data rate. Balanced routing on the printed circuit board is also important for preserving the noise-rejection benefit associated with differential signaling. Typical applications include industrial control links, test and measurement systems, point-to-point data acquisition, embedded equipment interfaces, and instrumentation networks operating at up to 120 kbaud. The device can also support point-to-point links between a host controller and a remote peripheral when both ends use compatible balanced signaling and termination. Design the power and signal paths carefully. Place the transceiver close to the connector, route driver and receiver traces as a balanced pair, observe the ground reference at the interface boundary, and validate the completed cable and load configuration against the EIA/TIA-562 requirements. A 1000 pF load is a meaningful capacitive budget, so cable length and receiver loading can materially affect usable communication distance. This product page combines the manufacturer’s operating limits with practical interface guidance, package information, sourcing context, and verified ordering references. It helps engineers distinguish the LTC1350CG from suffix and ordering variants while focusing on the parameters that determine board-level compatibility: 3.3 V operation, 120 kbaud performance, balanced RS-562 signaling, 3.5 V low-power operation, and the 28-terminal SSOP footprint.

RFQ Contact
LTC1380IGN#PBF - 8-Ch SMBus Analog Mux, 70Ohm | Analog Devices
LTC1380IGN#PBF

LTC1380IGN#PBF - 8-Ch SMBus Analog Mux, 70Ohm | Analog Devices

The Analog Devices LTC1380IGN#PBF is a CMOS single-ended 8-channel analog multiplexer with an SMBus-compatible two-wire digital interface, featuring 70 ohm on-resistance, 10 uA supply current, and a wide 2.7 V to +/-5 V supply range, housed in a 16-pin SSOP (SSOP-16) package. An analog multiplexer (mux) is a switching IC that selects one of several analog input signals and routes it to a single output under digital control, making it a foundational block in the signal-switching hierarchy: multiplexer switch IC -> analog switch -> data conversion front end -> signal chain. Unlike electromechanical relays, CMOS muxes such as the LTC1380 switch in microseconds, consume microamp-level power, and integrate the decode logic on-chip. Key differentiating features include the SMBus-compatible serial interface that requires only two wires (SCL and SDA), four hard-wired SMBus addresses selectable with two external address pins, and the Pb-free (RoHS) SSOP-16 package indicated by the #PBF suffix. The extremely low 10 uA supply current makes the part well suited to battery-powered and remotely powered data-acquisition systems. Architecturally, the LTC1380 uses CMOS transmission-gate switches driven by an on-chip decode stage controlled by the serial port. Break-before-make switching prevents momentary shorting of selected channels, and the 70 ohm on-resistance keeps insertion loss low in moderate-impedance signal paths. The wide 2.7 V to +/-5 V supply capability supports both single-supply 3 V/5 V logic systems and dual-supply analog domains for bipolar signals. Typical applications include industrial data-acquisition front ends, battery-powered sensor monitoring, automatic test equipment channel routing, and general-purpose analog signal selection in embedded systems with an SMBus or I2C-compatible controller. Design-wise, keep the off-channels' source impedance low and add an op-amp buffer after the mux output if the downstream load is capacitive or high-value, because the 70 ohm RON combines with load current to create gain error. This page synthesizes distributor pricing context, drop-in alternatives, pin/package guidance, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
LTC1409IG - 12-Bit 800ksps Sampling ADC | Analog Devices
LTC1409IG

LTC1409IG - 12-Bit 800ksps Sampling ADC | Analog Devices

Analog Devices LTC1409IG is a 12-bit, 800 ksps sampling analog-to-digital converter with a parallel interface in a 28-pin SSOP package. It supports true differential input, provides a 1 µs conversion time, and operates from ±5 V supplies while dissipating 80 mW. The converter is intended for precision signal acquisition, industrial control, instrumentation, communications, and data-processing systems requiring deterministic sampling without pipeline delay. A sampling ADC is a data-converter category that samples an analog input at a specified instant and converts it into a digital code. The LTC1409IG belongs to the successive-approximation-register family, where a sample-and-hold circuit captures the input before an internal 12-bit conversion completes. It includes a high-dynamic-range sample-and-hold stage and a precision internal reference, while also accepting an external reference when greater system-level control is required. Key characteristics include an 800 ksps maximum sampling rate, a 1 µs conversion time, and a ±2.5 V full-scale differential input range. The converter provides single-ended or differential signal handling, digital shutdown control, and selectable operating modes. Its specified maximum DC linearity and differential nonlinearity are ±1 LSB, while signal-chain performance reaches 72.5 dB SINAD and 86 dB THD at the Nyquist frequency. The architecture supports both internal and external reference operation. The internal reference has a stated temperature coefficient of 15 ppm/°C, providing a compact solution when a dedicated external reference would add cost or board area. Shutdown options include Nap, which reduces power dissipation to 4 mW, and Sleep, which reduces it to 10 µW, making the converter suitable for intermittently sampled acquisition systems. Typical applications include process-control loops, multichannel measurement systems, communications receivers, industrial instrumentation, waveform capture, and precision sensor acquisition. Its parallel data bus allows the converted word to be read directly by a microcontroller, DSP, FPGA, or other digital controller, making bus timing and signal-integrity layout important considerations. When designing a board around the LTC1409IG, preserve the specified dual-supply range and ensure adequate input settling before each conversion. Place input and reference components close to their associated pins, maintain short parallel-bus routes, and provide suitable decoupling. Confirm that the selected downstream logic voltage and acquisition timing support the converter's parallel interface and sampling requirements. This page combines manufacturer specifications, package information, verified source links, drop-in family references, and practical design guidance to support component selection, schematic planning, PCB layout, and replacement evaluation.

RFQ Contact
LTC1416CG - 14-Bit 400ksps Low-Power ADC | Analog Devices
LTC1416CG

LTC1416CG - 14-Bit 400ksps Low-Power ADC | Analog Devices

Analog Devices LTC1416CG is a low-power, 14-bit, successive-approximation sampling ADC with a conversion time of 2.2 microseconds, a maximum sampling rate of 400 ksps, and a 28-pin SSOP package. The converter accepts a bipolar full-scale input range of ±2.5 V and operates from ±5 V supplies while drawing 70 mW. A sampling ADC is a data-converter category that uses a sample-and-hold circuit and successive-approximation conversion to translate an analog voltage into a digital code. The LTC1416 belongs to the ADC, data-converter, signal-processing, and semiconductor hierarchy. Its high dynamic-range sample-and-hold front end makes it suitable for precision instrumentation, industrial measurement, data acquisition, and control systems that require accurate conversion without a high-power switching architecture. The principal characteristics are 14-bit resolution, 400 ksps throughput, and 2.2 microsecond conversion time. The Analog Devices datasheet also identifies ±2 LSB maximum integral nonlinearity, ±1.5 LSB maximum differential nonlinearity, and operation from ±5 V supplies. Two digitally selectable shutdown modes help reduce power consumption when conversion activity is intermittent. The converter supports internal or external reference operation and includes a precision reference according to the manufacturer product information. The parallel-output architecture supports direct connection to digital control logic when the converter is mounted close to the processor or FPGA. A SAR ADC is useful when deterministic latency, moderate resolution, and modest conversion rates matter more than very high throughput. This combination of 14-bit resolution, 400 ksps sampling, selectable shutdown modes, and bipolar input range allows the LTC1416 to balance measurement resolution, throughput, power use, and implementation complexity. Typical uses include process-control loops, analog sensor acquisition, laboratory measurement instruments, industrial data-logging equipment, and embedded systems that sample slowly varying or moderately changing analog signals. The internal reference can simplify designs where an external precision reference would add cost and board area, while external-reference operation offers a path for shared references or calibration schemes. When laying out the circuit, place input, reference, and bypass connections to minimize pickup around the high-impedance analog input. Use the manufacturer pin-description table when assigning signals and observe the specified acquisition, conversion, and shutdown timing. Check the power-supply requirements and reference selection carefully because incorrect sequencing or bypassing can degrade accuracy even when the nominal sampling rate is suitable. This product overview consolidates the converter's resolution, throughput, input range, power characteristics, shutdown options, and package details into an engineering-oriented selection reference. It also distinguishes verified pin-compatible family alternatives from broader functional ADC choices, helping designers evaluate PCB reuse, interface compatibility, and measurement requirements before committing to a layout.

RFQ Contact
LTC1418CN#PBF - 14-bit 200ksps Low Power SAR ADC | Analog Devices
LTC1418CN#PBF

LTC1418CN#PBF - 14-bit 200ksps Low Power SAR ADC | Analog Devices

The Analog Devices LTC1418CN#PBF (originally Linear Technology) is a low power, 200 ksps, 14-bit successive-approximation analog-to-digital converter (SAR ADC) offered in a 28-pin PDIP through-hole package. Key headline parameters include a 200 ksps sampling rate, 14-bit resolution, 15 mW typical power dissipation from a single 5 V or ±5 V supply, and selectable 14-bit parallel or serial data output format. The on-board high-performance sample-and-hold, precision reference, and internal timing keep external component count to a minimum, which simplifies board layout and reduces BOM cost. What is a SAR ADC? A successive-approximation analog-to-digital converter is a type of ADC that performs a binary search across an internal DAC to converge on the input voltage one bit per cycle. Within the broader hierarchy, this places SAR ADCs alongside pipelined, sigma-delta, and flash converters inside the data acquisition IC family. SAR converters deliver an excellent balance of speed, accuracy, and low power, which is why they remain a workhorse for industrial process control, instrumentation, and multiplexed data-acquisition front ends. Key features of the LTC1418CN#PBF include a built-in track-and-hold amplifier that eliminates the need for an external SHA, a typical differential non-linearity (DNL) of ±0.5 LSB, and bipolar/unipolar input capability when operated from ±5 V. Power-down mode reduces dissipation for battery-powered applications, and the wide analog input range (0 V to 5 V single-ended, ±5 V true bipolar) gives designers flexibility when digitizing transducer or sensor signals. Architecturally, the LTC1418 uses a charge-redistribution DAC array combined with a precision buried-Zener reference and auto-calibrated switch-capacitor front end. At 200 ksps, it sustains full 14-bit performance without missing codes, and the serial/parallel interface allows the same silicon to drop into either high-pin-count microcontroller buses or low-pin-count SPI controllers. Typical applications include industrial process-control data acquisition boards, portable or battery-powered instrumentation, multiplexed sensor read-back, and digital signal processing front ends. The 5 V single-supply capability also makes it suitable for legacy 5 V-only embedded designs. Designers should note that the LTC1418 is in the process of being discontinued; an SSOP-28 replacement (LTC1418CG#PBF) exists but is NOT pin-to-pin compatible with the DIP-28. Plan PCB rework or substitute silicon if the DIP-28 supply runs out. This page synthesizes Analog Devices datasheet data, distributor stock and pricing from DigiKey, and practical design considerations not found on manufacturer product pages.

RFQ Contact
LTC1545CG - 5/5 Multiprotocol Transceiver | Analog Devices
LTC1545CG

LTC1545CG - 5/5 Multiprotocol Transceiver | Analog Devices

The Analog Devices LTC1545CG is a software-selectable 5-driver, 5-receiver multiprotocol transceiver for RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, and X.21 interfaces. It is supplied in a 36-lead SSOP package and is intended for commercial-grade communications equipment requiring one physical design to cover several legacy serial protocols. A multiprotocol transceiver is an interface IC that combines drivers, receivers, and selectable termination or biasing functions so a data-communications port can operate with different electrical standards. The LTC1545CG provides five balanced driver channels and five receiver channels, allowing simultaneous control-signal and data-path operation in DTE or DCE port designs. Protocol selection is handled in software rather than through a permanently fixed physical interface. Key features include five drivers, five receivers, support for seven named serial protocols, and software-selectable cable termination. The manufacturer identifies the LTC1545 as production-available and presents it together with the LTC1543 as the core of a complete software-selectable DTE or DCE interface port. Termination can alternatively be implemented with the LTC1344A software-selectable cable-termination circuit or with discrete networks. Architecturally, the LTC1545 combines protocol-specific driver and receiver functions with control logic that configures the interface operating mode. This allows a single transceiver to serve equipment that must communicate with legacy RS-232, V.35, V.36, X.21, RS-449, or EIA-530 systems. The 36-lead SSOP provides enough external connections for driver outputs, receiver inputs, control inputs, and protocol-configuration signals while remaining compatible with established surface-mount assembly practices. Typical uses include multiprotocol network-interface cards, industrial data collectors, legacy telecommunications equipment, test systems, and DTE or DCE port designs. In each case, the transceiver simplifies inventory by replacing several protocol-specific interface ICs. Software-controlled configuration also allows the same controller and driver architecture to be reused across different installed-base environments. When designing a board around the LTC1545CG, confirm the exact protocol, connector assignment, termination requirement, and driver or receiver enable strategy against the pin-description table in the manufacturer datasheet. Leave filtering and protection to the external signal-chain components recommended for the selected protocol, and verify board-level timing and grounding against the equipment's EMC requirements. This page consolidates protocol coverage, package information, drop-in sourcing options, application guidance, and design cautions into one engineering reference. It also distinguishes verified device attributes from parameters that must be confirmed in the full datasheet before schematic capture or production release.

RFQ Contact
LTC1605-1CN#PBF - 16-Bit, 100ksps SAR ADC, 0-4V Input, 28-PDIP | Analog Devices
LTC1605-1CN#PBF

LTC1605-1CN#PBF - 16-Bit, 100ksps SAR ADC, 0-4V Input, 28-PDIP | Analog Devices

The Analog Devices LTC1605-1CN#PBF is a 16-bit, 100ksps successive-approximation analog-to-digital converter that operates from a single 5V supply, drawing only 55mW (typical) and housed in a 28-pin PDIP through-hole package. It integrates a sample-and-hold amplifier, a precision internal reference, a switched-capacitor 16-bit SAR ADC core, and a trimmed internal clock, providing a complete data-acquisition solution in a single IC. A successive-approximation register (SAR) ADC is a type of analog-to-digital converter that performs a binary search across the input voltage using an internal DAC and comparator; SAR ADCs are valued for low latency, deterministic conversion time, and excellent DC accuracy with no pipeline delay, making them well-suited for multiplexed data acquisition, industrial process control, and precision instrumentation where a single-channel, low-noise conversion is required. Key features include a 0V to 4V true-differential analog input range (industry-standard unipolar), ±2.0 LSB maximum integral nonlinearity (INL), guaranteed 16-bit no-missing-codes over temperature, and a flexible parallel data output interface (16-bit wide or two-byte) that connects directly to microprocessors, DSPs, and FIFOs. The internal 2.5V reference is trimmed for low drift; an external reference may be applied for higher absolute accuracy over temperature. A CONVST input and BUSY (EOC) output simplify handshaking with external logic. Architecturally, the device uses a charge-redistribution switched-capacitor DAC paired with a low-noise comparator and an SAR control engine; the input sample-and-hold acquires the signal on the rising edge of CONVST and the conversion completes in 8µs, after which data is presented on the parallel port with BUSY going low. Single 5V operation eliminates the negative supply required by many legacy bipolar ADCs, simplifying board power design. Typical applications include industrial process control and multi-channel data-acquisition front ends (paired with an external MUX), precision weighing scales and load-cell digitizers, bench-top and laboratory instrumentation, medical diagnostic equipment, and high-accuracy temperature or strain-gauge measurement systems. The LTC1605-1CN#PBF's commercial 0°C to 70°C operating range suits laboratory, factory-floor, and bench environments. When designing with this part, place 10µF (or larger) bypass capacitors close to the AVdd and DVdd pins and respect a star-ground topology between the analog input ground return and digital ground to avoid code-dependent noise coupling into the reference. The 28-PDIP package is convenient for prototype boards, sockets, and through-hole assembly but is not recommended for new high-density surface-mount designs - consider the SSOP-28 (LTC1605-1CG#PBF) for SMT layouts. This page synthesizes distributor pricing, true drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
LTC1605-1IN#PBF - 16-Bit 100ksps SAR ADC | Analog Devices
LTC1605-1IN#PBF

LTC1605-1IN#PBF - 16-Bit 100ksps SAR ADC | Analog Devices

The Analog Devices LTC1605-1IN#PBF is a 16-bit, 100 ksps successive-approximation analog-to-digital converter (SAR ADC) in a 28-pin PDIP (N) through-hole package. According to the Analog Devices datasheet, the device draws only 55 mW (typical) from a single 5 V supply, includes a sample-and-hold front-end, a precision internal reference, and a trimmed internal clock, providing a complete 16-bit data-acquisition solution in one IC. The unipolar input range is 0 V to 4 V (LTC1605-1 variant; LTC1605-2 variant covers ±4 V bipolar). The converter features a microprocessor-compatible 16-bit or two-byte parallel output port for direct connection to data buses and DSP/microcontroller interfaces. A SAR ADC is a successive-approximation-register analog-to-digital converter that uses a binary-search algorithm and an internal capacitive DAC to resolve the input voltage one bit at a time per clock cycle. SAR ADCs occupy the middle ground between delta-sigma (high resolution, low speed) and flash (very high speed, low resolution) architectures. They are the dominant choice for 12-16 bit industrial data-acquisition systems running at 10 ksps to 1 Msps, particularly when deterministic latency and a parallel/serial output are required. The LTC1605-1IN#PBF inherits the lineage of the industry-standard LTC1605 family, all of which share the same 28-pin pinout and timing characteristics for drop-in upgrades. Key features include 16-bit no-missing-codes performance, 86 dB typical signal-to-noise ratio, a 100 ksps sampling rate, and an external reference option for systems that require better temperature drift than the internal 2.5 V reference provides. The 28-pin PDIP package is through-hole, simplifying prototyping and field replacement for industrial instrumentation. Typical applications include industrial process control, multi-channel data-acquisition boards, weigh-scale and load-cell digitizers, panel meters, instrumentation front-ends, and bench-top test-and-measurement equipment. The 5 V single-supply operation and parallel data port allow direct connection to legacy parallel-signal processors and modern microcontrollers/DSPs without additional level translation. When designing with the LTC1605-1IN#PBF, ensure the analog input is buffered if the source impedance exceeds the datasheet-specified value, and decouple VDD with a 10 µF tantalum in parallel with a 0.1 µF ceramic placed within 1 cm of the supply pin. The #PBF suffix indicates lead-free (Pb-free) and RoHS-compliant construction, qualifying the part for modern and export-controlled designs.

RFQ Contact
LTC1605-2CN#PBF - 16-Bit 100ksps ±4V Bipolar SAR ADC | ADI
LTC1605-2CN#PBF

LTC1605-2CN#PBF - 16-Bit 100ksps ±4V Bipolar SAR ADC | ADI

The Analog Devices LTC1605-2CN#PBF is a 16-bit, 100 ksps successive-approximation analog-to-digital converter that operates from a single 5 V supply and dissipates only 55 mW typical. Housed in a 28-pin PDIP through-hole package, the device integrates a sample-and-hold front end, a precision internal reference, a switched-capacitor SAR core, and a trimmed internal clock, enabling a complete 16-bit conversion solution in one IC. The -2 suffix denotes a bipolar ±4 V analog input range, which makes the part well suited to industrial signal acquisition that uses a true bipolar front end. A successive-approximation register (SAR) ADC is a type of data converter that performs one binary bit decision per conversion cycle, using an internal comparator, DAC, and successive-approximation logic. SAR converters sit in the broader ADC hierarchy between delta-sigma (high resolution, low speed) and flash (high speed, low resolution), and are favored for multiplexed data-acquisition systems because they perform a complete, deterministic conversion in N clock cycles with no pipeline latency. The LTC1605-2 exemplifies this architecture with its single-shot, software-controlled conversion cycle. Key specifications of the LTC1605-2 include 16-bit resolution with no missing codes, ±4 V bipolar input range, 100 ksps sampling rate, parallel data interface, ±2.5 LSB INL typical, and integrated reference. The internal clock and the integrated reference eliminate external ADC support components, simplifying the analog front end. Because the part is single-supply 5 V with a true bipolar differential input stage, designers can connect the output of a ±4 V instrumentation amplifier directly to the ADC inputs with minimal signal conditioning. The architecture uses a charge-redistribution switched-capacitor DAC inside the SAR loop, a technique that yields excellent DC linearity for instrumentation workloads. The integrated 4.096 V reference is trimmed at the factory, so the converter achieves specified noise and INL performance without external reference components, although a 2.2 µF bypass close to the REF pin is required for full accuracy. Typical applications include process-control analog input modules, industrial PLC analog front ends, precision data-acquisition boards, multichannel instrumentation front ends with bipolar signals, and laboratory instrumentation that requires 16-bit accuracy without high-speed throughput. Designers in these segments value the deterministic conversion latency and the simple parallel read interface. When designing the PCB, place the 2.2 µF REF bypass capacitor and the 10 µF VCC decoupling capacitor as close to the IC pins as possible. Use a ground plane under the analog section and keep digital return currents out of the analog ground path. Use the S/H (sample-and-hold) pin or the CS and RD signals to start conversions; the LTC1605-2 does not auto-run. This page synthesizes distributor pricing, pin-compatible ADI alternatives in the same 28-PDIP footprint, and practical layout notes beyond the manufacturer datasheet, helping engineers evaluate LTC1605-2CN#PBF for drop-in upgrades, second sources, and bipolar-input acquisition channels.

RFQ Contact
LTC1605ACN - 16-Bit 100ksps ADC with Bipolar ±10V Input | Analog Devices
LTC1605ACN

LTC1605ACN - 16-Bit 100ksps ADC with Bipolar ±10V Input | Analog Devices

The Analog Devices LTC1605ACN is a 16-bit, 100 ksps sampling analog-to-digital converter (ADC) housed in a 28-pin PDIP through-hole package. It draws only 55 mW (typical) from a single +5 V supply, accepts a bipolar ±10 V input range, and features an internal precision reference with trimmed internal clock for easy standalone operation. An analog-to-digital converter (ADC) is a data-converter integrated circuit that converts a continuous analog voltage into a discrete digital code, occupying a key position in the signal-chain hierarchy: transducer -> analog front end / signal conditioning -> ADC -> digital processor. Successive-approximation register (SAR) ADCs in particular combine a sample-and-hold, precision reference, switched-capacitor DAC and SAR logic to deliver one conversion per clock, with low latency and deterministic behavior well suited to multiplexed data acquisition and industrial instrumentation. Key features of the LTC1605ACN include ±2.0 LSB (max) INL over temperature, guaranteed 16-bit no missing codes, a microprocessor-compatible 16-bit or two-byte parallel output port, and the ability to be driven by an external reference when higher absolute accuracy is required across temperature. Synchronous sampling and a wide input range let it directly digitize industrial ±10 V signals without external scaling amplifiers. The device uses a precision bandgap reference and trimmed internal clock, simplifying the analog front end to a simple RC input network plus an external reference option for temperature-stable accuracy. Successive-approximation architecture yields deterministic latency and excellent DC linearity for instrumentation applications. Typical applications include industrial process control data acquisition boards, multichannel multiplexed data loggers, instrumentation and measurement front ends, and legacy factory automation I/O subsystems. The bipolar ±10 V range lets it connect directly to legacy industrial sensors and 4-20 mA loop resistors. Design with the device by ensuring the analog input pin sees a low-impedance buffer or RC network matching the ADC's switched-capacitor front end, and by tying REFCOMP to a 10 µF bypass capacitor near the pin to minimize reference noise. Latency is one conversion clock, simplifying timing analysis for sequential multiplexer scans.

RFQ Contact
LTC1605AIN - 16-Bit 100ksps Sampling ADC ±10V | Analog Devices
LTC1605AIN

LTC1605AIN - 16-Bit 100ksps Sampling ADC ±10V | Analog Devices

The Analog Devices LTC1605AIN is a 16-bit, 100ksps sampling analog-to-digital converter that draws only 55 mW (typical) from a single 5V supply, packaged in a 28-pin SSOP. It integrates a sample-and-hold amplifier, a precision internal reference, a switched-capacitor successive-approximation ADC core, and a trimmed internal clock, providing a complete bipolar-input ADC solution. The bipolar analog input range is ±10V, suitable for industrial process control, instrumentation, and signal-isolation data-acquisition front-ends. An ADC (analog-to-digital converter) is a semiconductor device that converts a continuous analog voltage or current into a discrete digital code; sampling ADCs additionally include a sample-and-hold front-end that captures and freezes the input at a precise moment so that the conversion can proceed without aliasing. In the broader component hierarchy, the LTC1605AIN is a successive-approximation-register (SAR) ADC, a sub-category of data converters that sits under interface/ADC ICs in mixed-signal systems. SAR ADCs are favored for their deterministic latency, low power consumption, and excellent DC accuracy compared with delta-sigma or pipeline architectures, making them ideal for multiplexed data-acquisition systems. Key features include ±2.0 LSB maximum integral nonlinearity, guaranteed no missing codes at 16 bits, ±10V true bipolar input range from a single 5V supply, and a 55 mW typical power dissipation. The part is specified over the commercial 0°C to 70°C operating range, with the 'N' suffix indicating an SSOP-28 package and 'I' indicating the commercial temperature grade. The internal reference and trimmed clock eliminate the need for external components, simplifying board layout and reducing BOM cost. Architecturally, the LTC1605AIN combines a fast bipolar-input track-and-hold with a charge-redistribution SAR core and an on-chip reference. The trimmed internal clock removes the requirement for an external timing source, and the parallel output interface delivers conversion results in a single read cycle. The 100ksps throughput makes it well suited to multiplexed multi-channel systems where each channel can still be sampled at several kHz. Typical applications include industrial process control and instrumentation, multiplexed data-acquisition systems, signal-isolation front-ends, and portable or battery-powered test equipment. The ±10V bipolar input makes it a natural drop-in for legacy 5V-only signal chains migrating from older bipolar ADC designs. When designing with this part, allocate adequate board area for the analog input anti-alias filter and bypass the supply pin with a 10 µF tantalum plus 0.1 µF ceramic capacitor within 10 mm of the device. The analog and digital grounds should be tied at a single star point beneath the IC to minimize noise coupling from the parallel output bus into the sensitive input front-end. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the Site MPN list, and practical design notes not found in the manufacturer datasheet, enabling faster BOM selection for engineers maintaining or designing-in the LTC1605AIN.

RFQ Contact
LTC1605CN#PBF - 16-Bit 100ksps SAR ADC, ±10V Bipolar | ADI
LTC1605CN#PBF

LTC1605CN#PBF - 16-Bit 100ksps SAR ADC, ±10V Bipolar | ADI

The Analog Devices (formerly Linear Technology) LTC1605CN#PBF is a 100 ksps, 16-bit sampling analog-to-digital converter (ADC) that draws only 55 mW (typical) from a single 5 V supply, housed in a 28-pin PDIP (through-hole) package. The device integrates a sample-and-hold front end, a precision buried-zener reference, a switched-capacitor successive-approximation ADC core, and a trimmed internal clock, providing a complete data-acquisition front end in one IC. A successive-approximation register (SAR) ADC is a precision converter architecture that performs a binary search across an internal DAC for each conversion, achieving deterministic low-latency (one conversion cycle) results with no pipeline delay. SAR ADCs are widely used in industrial, instrumentation, and process-control applications where DC accuracy, high linearity, and excellent AC performance at moderate sampling rates are required. The LTC1605 sits in the precision SAR family alongside the 14-bit LTC1410 and 12-bit LTC1290, sharing a common analog front-end philosophy and pinout philosophy. Key specifications include 16-bit resolution with no missing codes, ±2.0 LSB maximum integral nonlinearity (INL), ±10 V true-bipolar input range from a single 5 V supply, 100 ksps sampling rate, and 55 mW typical power dissipation. The integrated reference eliminates external reference components, simplifying the bill of materials. The parallel data interface allows direct connection to microprocessors, FPGAs, or DSPs without serial-deserialization glue logic. Typical applications include industrial process control, multiplexed data-acquisition systems, precision instrumentation, seismic and weigh-scale digitizers, spectrum and vibration analysis front ends, and bench-top DMM front ends. The ±10 V true-bipolar input is a key differentiator, allowing direct digitization of industrial sensor outputs (4-20 mA loops scaled to voltage, strain-gauge bridges, thermocouple amplifiers) without external signal conditioning. When designing with the LTC1605, allocate at least 8 analog input pins plus dedicated AGND and DGND pins, and follow ADI's recommended four-layer board with separate analog and digital ground planes joined at a single point near the IC. The internal reference requires a 10 µF bypass capacitor on the REFCOMP pin for optimal linearity. This page synthesizes distributor pricing, drop-in 28-PDIP alternatives (LTC1605IN, LTC1605-1CN, LTC1605-2CN), and practical design notes not aggregated on any single manufacturer or distributor page.

RFQ Contact