Products (44,000+)

LTC2662HUH-12#PBF - 5Ch 12-bit Current-Source DAC | Analog Devices
LTC2662HUH-12#PBF

LTC2662HUH-12#PBF - 5Ch 12-bit Current-Source DAC | Analog Devices

The Analog Devices LTC2662HUH-12#PBF is a 5-channel, 12-bit current-source digital-to-analog converter (DAC) that delivers five high-compliance current source outputs with a guaranteed 1 V dropout at 200 mA, housed in a 32-pin QFN (5x5 mm) package. Each output draws its current from a dedicated positive supply pin that accepts 2.85 V to 33 V, supporting load voltages up to 32 V and full-scale outputs up to 300 mA with eight per-channel programmable current ranges. Multiple channels can be paralleled for combined outputs up to 1.5 A, and internal 12 ohm switches allow any output pin to connect to an optional negative V- supply and sink up to 80 mA. A current-source DAC (also called a current-output DAC or IDAC) is a digital-to-analog converter whose output stage delivers a programmable current rather than a voltage. In the signal-chain taxonomy it sits below general-purpose DACs and above simple current mirrors: IDAC -> DAC -> data converter -> signal chain IC -> semiconductor. This category is the preferred building block when the load itself has a well-defined compliance voltage and the application requires precise, fast, and noise-immune current programming, such as LED biasing, laser diode drivers, and programmable current sources in test instruments. The LTC2662 integrates a precision reference, per-channel range registers, and a high-compliance output stage on a single die. The device operates over the -40 C to +125 C automotive/industrial temperature range and includes a serial peripheral interface (SPI) for digital configuration. The wide 32 V compliance and 200 mA continuous per-channel capability eliminate the need for external op-amp current boosters in many applications, while the parallelable architecture scales to multi-amp systems. The QFN-32 (5x5) package exposes a thermal pad that must be soldered to a ground copper pour for rated thermal performance. Typical applications include laser diode drive, LED biasing and dimming, programmable current sources, solenoid/actuator drive, and process-control instrumentation where bipolar or unipolar high-compliance currents are required. The 32 V compliance directly supports 28 V nominal industrial buses, while the 80 mA sink capability handles thermistor or Peltier biasing. When designing with this DAC, treat each output as an independent current source with its own V+ pin; use Kelvin-sense layout when load currents exceed 100 mA. Decouple every V+ pin with a 1 uF ceramic plus 10 uF bulk capacitor, and parallel outputs by tying OUT_x pins together before the load to achieve higher currents with matched range settings. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives in the QFN-32 footprint, and practical design notes not consolidated in the Analog Devices datasheet.

RFQ Contact
LTC2662HUH-16#PBF - 16-Bit 5-Ch 300mA Current-Source DAC | ADI
LTC2662HUH-16#PBF

LTC2662HUH-16#PBF - 16-Bit 5-Ch 300mA Current-Source DAC | ADI

The Analog Devices LTC2662HUH-16#PBF is a 16-bit, five-channel current-source digital-to-analog converter (DAC) housed in a 32-pin QFN (5x5 mm) package, providing five high-compliance current source outputs with a guaranteed 1 V dropout at 200 mA and load voltage support up to 32 V. The LTC2662 family delivers 5 independently programmable channels of monotonic 16-bit (or 12-bit) current-output DAC with SoftSpan architecture that allows output ranges from 3 mA to 300 mA full-scale, all sharing the same 32-QFN footprint. What is a current-source DAC? A current-output digital-to-analog converter converts a digital code into a precise analog current, rather than voltage. Within the data-converter hierarchy, the LTC2662 belongs to the DAC family, more specifically current-steering or current-source DACs, which are widely used to drive laser diodes, precision actuators, programmable current bias, and process-control loops. Compared with voltage-output DACs, current-output parts eliminate output buffers and headroom-loss, allowing the load to sit at a high compliance voltage while the DAC itself drops just 1 V. Key features of the LTC2662HUH-16#PBF include guaranteed 1 V dropout at 200 mA per channel, 32 V load compliance, per-channel SoftSpan programmable full-scale current from 3 mA to 300 mA, a wide supply range (AVDD up to 5.5 V, load rail up to 32 V), and a flexible serial SPI-compatible interface with per-channel readback. The device uses a precision internal reference and offers daisy-chain capability for multi-device synchronization. The architecture is built around five matched current cells steered by a 16-bit segmented architecture. The internal reference and precision thin-film resistors deliver INL of approximately 1 LSB and DNL of ±0.5 LSB on the -16 grade. The wide compliance window (1 V to 32 V headroom over the load) lets the LTC2322662 directly drive H-bridges, optocouplers, and laser diodes without external driver stages. Typical applications include laser-diode driver bias for telecom and instrumentation, programmable current sources for industrial process control, optical attenuators, precision actuator drive in medical and test equipment, and 4 mA to 20 mA / 0 mA to 20 mA loop-driving when combined with an external boost stage. The 32-QFN footprint fits dense PCB designs and keeps channel-to-channel thermal coupling manageable. Design tip: decouple the AVDD pin with a 10 uF + 100 nF pair placed within 5 mm of the IC, and reserve a small copper island under the exposed pad to draw heat out of the package when more than two channels are operated near 200 mA. Ensure the load path returns to the LTC2662's GND to avoid ground-loop errors in the high-compliance current output. This page synthesizes DigiKey/Mouser distributor pricing, drop-in same-package variants, and application-specific design notes not available in the manufacturer datasheet alone.

RFQ Contact
LTC2846IG - 3.3V Multiprotocol Transceiver w/ Termination | Analog Devices
LTC2846IG

LTC2846IG - 3.3V Multiprotocol Transceiver w/ Termination | Analog Devices

The Analog Devices LTC2846IG is a 3-driver/3-receiver multiprotocol transceiver with on-chip cable termination, housed in a 36-pin SSOP (Industrial Grade) package. Operating from a single 3.3V supply, it supports software-selectable protocols including RS232, RS449, EIA530, EIA530-A, V.35, V.36 and X.21, with a 1ku list price starting from $19.21 as of 2026-10-08. An RS-232/RS-422/RS-485 multiprotocol transceiver is a single-chip interface IC that combines multiple line-driver and receiver channels, allowing one hardware design to be reconfigured in software between legacy serial standards. The transceiver family (LTC2844/LTC2845/LTC2846) is typically deployed in DTE or DCE serial port designs where a single physical connector must handshake with many types of legacy equipment, and on-chip termination removes the need for external resistor networks on V.35/V.36/X.21 lines. Key features include 3 drivers and 3 receivers, on-chip cable termination resistors, software-selectable protocol mode via logic pins, integrated 1.2MHz boost switching regulator that converts the 3.3V supply to 5V for V.35/V.36/X.21 driver levels, and TUV Rheinland NET1/NET2/TBR2 certification. The Industrial Grade (-40C to +85C) temperature rating supports telecom and industrial environments, while the SSOP-36 footprint integrates easily into legacy backplane designs. The architecture combines a digital mode-control block, an on-chip boost regulator (1.2MHz), six terminated line drivers/receivers, and charge pumps for RS-232 compliance. This integration reduces the typical discrete BOM of a multiprotocol port from ~40 components to a single IC plus a few passive components. Typical applications include multiprotocol serial ports in WAN routers, telecom DSU/CSU equipment, V.35/V.36/X.21 line cards, industrial serial gateways, and legacy-to-modern serial protocol converters. When paired with the LTC2844 (clock/data transceiver) or LTC2845 (control-signal transceiver) it forms a complete software-selectable DTE/DCE port. For design, ensure the MODE_SELECT pins are driven through low-capacitance logic and that the boost regulator output (V+ pin) is bypassed with at least 10uF ceramic + low-ESR electrolytic to meet V.35 driver rise/fall time specifications.

RFQ Contact
LTC2850HMS8#TRPBF - 3.3V 20Mbps RS485/RS422 Transceiver | ADI
LTC2850HMS8#TRPBF

LTC2850HMS8#TRPBF - 3.3V 20Mbps RS485/RS422 Transceiver | ADI

The Analog Devices LTC2850HMS8#TRPBF is a low-power 3.3V RS485/RS422 transceiver in an 8-pin MSOP package, supporting data rates up to 20 Mbps with half-duplex (1 driver / 1 receiver) operation. The receiver offers one-eighth unit load, enabling up to 256 nodes on a single bus (C-, I-grade), and integrates a failsafe feature that guarantees a logic-high output under floating or shorted input conditions. The driver maintains high output impedance across the entire common-mode range when disabled, ensuring robust multi-node bus behavior. An RS485/RS422 transceiver is a physical-layer interface IC that converts between the differential signaling used on industrial twisted-pair buses and the single-ended logic levels used by UARTs, MCUs, and FPGAs. RS485 supports multipoint half/full-duplex buses over long distances (up to 1200 m), while RS422 is typically point-to-point. The LTC2850 belongs to the broader line transceivers -> interface ICs -> integrated circuits taxonomy and is part of the LTC2850/LTC2851/LTC2852 family from Analog Devices (formerly Linear Technology). Key features include ±15 kV ESD protection on the bus pins (H-grade designation), thermal shutdown, short-circuit protection, and a wide common-mode range that exceeds the RS485 standard requirement. The H-suffix variant specifies the high-ESD rating and the -40 °C to +125 °C automotive temperature grade, making it suitable for harsh industrial and automotive environments. Its 3.3V supply operation minimizes power dissipation in battery-powered and point-of-load regulated systems. The architecture uses a differential line driver with slew-rate-limited outputs to reduce EMI while still delivering 20 Mbps throughput. Internal hysteresis on the receiver inputs combined with the failsafe circuit ensures clean logic transitions even with significant bus attenuation or noise. The device draws low quiescent current, allowing many transceivers to share a single 3.3V rail without thermal concerns. Typical applications include industrial fieldbus networks (Modbus, Profibus DP), building automation (BACnet, RS485 lighting control), automotive body and chassis networks, point-of-sale terminals, and long-cable RS422 point-to-point links. The wide common-mode range also supports harsh electrically noisy environments such as motor drives and factory automation. When designing with this part, place 100 nF decoupling capacitors as close as possible to the VCC pin and provide proper cable termination (typically 120 Ω) at both ends of the bus. The half-duplex topology requires that only one driver be enabled at a time; software UART flow control or hardware direction-control timing must enforce this to avoid contention. This page consolidates distributor pricing, drop-in pin-compatible alternatives, and practical PCB/EMI design notes that go beyond what is typically printed in the manufacturer datasheet, helping engineers shorten design cycles.

RFQ Contact
LTC2852IMS#PBF - 3.3V 20Mbps RS485/RS422 Transceiver | ADI
LTC2852IMS#PBF

LTC2852IMS#PBF - 3.3V 20Mbps RS485/RS422 Transceiver | ADI

The Analog Devices LTC2852IMS#PBF is a low-power, 3.3V full-duplex RS485/RS422 transceiver rated for 20 Mbps signaling and housed in a 10-pin MSOP package. It features a one-eighth unit-load receiver input (supporting up to 256 nodes per bus on C- and I-grade devices), integrated hot-swap capable driver outputs, and a failsafe receiver that guarantees a logic-high output under floating, shorted, or terminated bus conditions. An RS485/RS422 transceiver is a differential line driver/receiver IC that translates between a single-ended UART/logic interface and a twisted-pair differential bus, enabling robust, long-reach, noise-immune communication in industrial, building-automation, and instrumentation systems. The LTC2852 belongs to the broader RS-422/RS-485 interface IC category (sub-category of Interface ICs) within the broader semiconductor power management and signal-chain ecosystem. Its 3.3V supply aligns with modern low-voltage MCUs and FPGAs, eliminating the level shifters required by legacy 5V transceivers. Key features include 3.3V single-supply operation, 20 Mbps data rate, 1/8th unit load (256-node fan-out on C/I grade), integrated hot-swap/tolerant driver outputs that remain high-impedance across the full common-mode range when disabled, low current per package (500 µA typical supply current), and industry-standard RS485/RS422 pinout. The MSOP-10 footprint enables compact node designs typical of multi-drop industrial backbones. Internally, the LTC2852 uses a precision differential line driver with slew-rate-limited edges (for low EMI) and a window-comparator receiver topology that detects 200 mV differential signals as required by TIA/EIA-485. The one-eighth unit-load input impedance reduces bus loading by 8× compared to legacy 1-unit-load parts, allowing more nodes on the same bus without exceeding the 32-unit-load RS485 specification limit. Typical applications include industrial fieldbus networks (Modbus, Profibus DP at 20 Mbps), building automation (BACnet MS/TP, lighting control), point-of-sale peripherals, multi-drop motor controller links, and RS422 point-to-point communication between embedded controllers and sensors. Designers choose the LTC2852 when they need a 3.3V-only transceiver with a small package, robust hot-swap performance, and high node count. When designing with this device, place 100 nF supply bypass capacitors within 5 mm of the VCC pin, use a 100 Ω termination resistor at each bus end, and verify common-mode protection in electrically noisy environments. The #PBF suffix denotes a lead-free, RoHS-compliant finish. This page synthesizes distributor pricing, parametric alternates, and practical design notes that complement - and go beyond - the manufacturer datasheet's nominal spec table.

RFQ Contact
LTC2862AIS8-2 - ±60V RS485/RS422 Transceiver | Analog Devices
LTC2862AIS8-2

LTC2862AIS8-2 - ±60V RS485/RS422 Transceiver | Analog Devices

The Analog Devices LTC2862AIS8-2 is a low-power, half-duplex RS485/RS422 transceiver with ±60V fault protection, operating on 3V to 5.5V supplies and housed in an 8-pin SOIC package. It supports two speed grades selectable via part variant: 20Mbps (the -2 suffix denotes a high-speed version) or 250kbps, with 1/1 driver/receiver count. The interface pins withstand ±60V overvoltage faults during all modes of operation including power-down. An RS485/RS422 transceiver is a physical-layer device that converts between a single-ended UART/CMOS logic signal on the microcontroller side and a robust differential signal on the bus side, enabling reliable serial communication over twisted-pair cables at distances up to 1200 meters. RS485 is the de-facto standard for industrial multipoint buses (Modbus RTU, Profibus, DMX512) while RS422 is used for point-to-point high-speed links; the LTC2862 family supports both. Half-duplex means one differential pair is shared between transmit and receive, with direction controlled by a logic pin. Key features include ±60V fault tolerance on the bus pins, IEC 61000-4-2 Level 4 ESD protection (typically 8 kV contact, 15 kV air per the manufacturer's IEC ESD rating), current-limited drivers, thermal shutdown, and a fully balanced differential receiver threshold for low duty-cycle distortion. The 8-pin SOIC package is pin-compatible with legacy LT1785/LT1791 footprints and the original LTC2862 family, enabling direct board replacement. The LTC2862A uses a CMOS process with switched-capacitor charge pump to generate the ±60V fault-tolerant driver supply. The architecture delivers low quiescent current during idle while still maintaining high drive strength during bus arbitration, and the receiver exhibits 250 mV typical hysteresis with a 50 mV worst-case offset to meet TIA/EIA-485-A. Typical applications include industrial fieldbus networks (Modbus, Profibus), solar inverter monitoring, building automation (BACnet), motor control encoder links, and any 3V-5V MCU interface that must survive miswiring, ESD strikes, or transient overvoltage events on long cable runs. The wide 3V-5.5V supply range also supports battery-powered remote sensor nodes. When designing with this device, place 100 nF decoupling close to VCC and use twisted-pair cable with proper termination (120 Ω) at the bus ends. The -2 suffix denotes 20 Mbps high-speed grade; the -1 variant is 250 kbps low-EMI grade - select based on your data rate and EMI budget.

RFQ Contact
LTC2863IS8-1 - ±60V Fault-Protected RS485/RS422 Transceiver | ADI
LTC2863IS8-1

LTC2863IS8-1 - ±60V Fault-Protected RS485/RS422 Transceiver | ADI

The Analog Devices LTC2863IS8-1#PBF is a ±60V fault-protected, 3V to 5.5V supply, full-duplex RS485/RS422 transceiver housed in an 8-pin SOIC (IS8) package. Per the manufacturer datasheet, it integrates one driver and one receiver (1/1), supports data rates up to 20 Mbps, and tolerates ±60V on the bus pins without damage, a level that exceeds the typical RS485 common-mode range of -7V to +12V by a wide margin. A transceiver is a semiconductor device that bridges two distinct electrical interfaces, in this case translating between low-voltage CMOS logic on the controller side and the differential, bus-terminated signaling required by the RS485/RS422 standard. RS485/RS422 transceivers sit inside the broader interface-IC hierarchy: interface IC > line driver/receiver > differential transceiver > RS485/RS422 transceiver. The LTC2863 family is positioned for harsh industrial bus networks where hot-plug events, wiring faults, and surge exposure are routine. Key features include ±60V fault protection on driver outputs and receiver inputs, ±25V HBM ESD protection on the bus pins, 1/8 unit load (up to 256 nodes per bus), current-limited drivers with thermal shutdown, and a fully balanced differential receiver threshold that minimizes duty-cycle distortion. The -1 suffix denotes the full-duplex (no shared DE/RE control timing constraint) pinout variant in the 8-lead SOIC; the -2 variant differs in enable logic. Per the manufacturer datasheet, MP-grade (-55°C to 125°C) and DFN package options are also available in the LTC2863 family. Architecturally, the device combines a differential line driver with a wide-input-range differential receiver, both protected by on-chip TVS-style clamping structures. The 3V-5.5V VCC range allows direct connection to 3.3V or 5V microcontrollers without level shifters, simplifying BOM and reducing board area. Pin compatibility with the LT1785 and LT1791 families (per Analog Devices product page) means existing designs can be ruggedized against field faults with no layout rework. Typical applications include industrial fieldbus networks (Modbus, Profibus, BACnet), building automation, motor drive feedback links, smart-grid metering, and any long-cable RS485 link exposed to installation transients or mis-wiring. The ±60V tolerance protects against accidental AC mains contact on the bus. When laying out the LTC2863IS8-1, keep the bus traces short and matched, place the bus termination at the end nodes, and provide a solid ground plane; the IC's internal fault protection does not replace good EMC practice. Use a 100nF decoupling capacitor close to VCC and add a 10µF bulk capacitor if the supply is shared with switching regulators.

RFQ Contact
LTC2870IFE - RS232/RS485 Multiprotocol Transceiver | Analog Devices
LTC2870IFE

LTC2870IFE - RS232/RS485 Multiprotocol Transceiver | Analog Devices

The Analog Devices LTC2870IFE is a pin-configurable multiprotocol transceiver supporting RS232, RS485, and RS422 on shared I/O lines, operating from a single 3V to 5.5V supply in a 28-pin TSSOP-EP package. The device integrates switchable termination resistors, configurable as two single-ended RS232 transceivers or one differential RS485/RS422 transceiver, with 2/2 (driver/receiver) channel count. A multiprotocol transceiver is a mixed-standard interface IC that allows a single port to communicate over multiple physical-layer protocols (RS232 point-to-point, RS485/RS422 multi-drop differential). The LTC2870 belongs to the transceiver -> line driver/receiver -> interface IC -> integrated circuit hierarchy. This protocol flexibility reduces BOM count when a system must support both legacy RS232 equipment and modern differential RS485 industrial fieldbuses without two separate transceivers. Key features include ±15 kV ESD protection on the transceiver I/O pins (HBM), integrated switchable RS485 120 ohm termination, full-duplex and half-duplex RS485 modes, slew-rate-limited RS485 driver for low EMI, and a wide common-mode range exceeding the RS485 requirement. The exposed pad (TSSOP-EP) package improves thermal dissipation for high-load industrial environments. Logic inputs are 5V tolerant when operating from 3.3V supply, simplifying level shifting with MCUs and FPGAs. Technically, the LTC2870 uses charge-pump technology for RS232 ±5V drivers while running from a single low-voltage rail, and a precision differential line driver for RS485/RS422. Internal logic configures the protocol by setting mode pins; the shared bus pins are reorganized between single-ended and differential operation without external switching. The receiver features 25 mV typical hysteresis for noise immunity on long RS485 cables. Typical applications include industrial programmable logic controllers (PLCs) with mixed RS232/RS485 ports, point-of-sale (POS) terminals, building automation gateways, multi-protocol instrumentation, and HVAC controllers. The integrated termination eliminates external resistor networks and improves field reliability. When designing with this part, place 0.1uF decoupling capacitors close to VCC pins and connect the exposed pad to a low-impedance ground plane for thermal and EMI performance. Verify mode-pin logic levels match the selected protocol during firmware development to avoid bus contention.

RFQ Contact
LTC2870IFE#PBF - RS232/RS485 Multiprotocol Transceiver | Analog Devices
LTC2870IFE#PBF

LTC2870IFE#PBF - RS232/RS485 Multiprotocol Transceiver | Analog Devices

Analog Devices LTC2870IFE#PBF is a robust pin-configurable multiprotocol transceiver supporting RS232, RS485, and RS422 protocols from a single 3V to 5.5V supply, housed in a 28-pin TSSOP-EP (FE) package. The LTC2870 integrates one RS485 differential transceiver and two RS232 single-ended transceivers on shared I/O lines, with automatic integrated termination resistor selection. According to the Analog Devices LTC2870/LTC2871 datasheet, the device supports data rates up to 20 Mbps for RS485 and 500 kbps for RS232, with ±25 kV ESD (HBM) protection on the bus pins. An RS232/RS485 multiprotocol transceiver is an interface IC that bridges a UART, microcontroller, or processor to a physical serial bus. The RS232 standard uses single-ended signaling (logic-high and logic-low on separate lines with ±5V to ±15V swings) and is common in point-to-point links to legacy PCs and industrial controllers. The RS485 standard uses differential signaling (A-B differential voltage) and enables multipoint half-duplex or full-duplex networks up to 1200 m with up to 32 unit loads. Multiprotocol transceivers combine both physical layers on shared pins so a single PCB footprint can serve multiple end-equipment variants, reducing BOM and qualification cost. Key features of the LTC2870 include shared I/O lines between RS232 and RS485 modes, automatic or logic-controlled 120 ohm RS485 termination, ±25 kV ESD HBM on the bus I/O pins, hot-swap glitch protection, and a low-current shutdown mode. The integrated loopback mode allows self-test of the RS232 path without external cabling. The single 3V to 5.5V supply eliminates the negative charge pump traditionally required for RS232, simplifying power tree design. Typical applications include industrial multipoint fieldbus nodes, point-of-sale terminals, RS232-to-RS485 protocol converters, and any system that must communicate to both legacy RS232 equipment and modern RS485 networks. The TSSOP-EP package provides low thermal resistance for reliable operation at the extended industrial temperature range. When designing with the LTC2870, the shared I/O pins require careful PCB routing to avoid coupling between RS232 single-ended and RS485 differential traces; the exposed pad must be soldered to a thermal copper pour for specified thermal performance.

RFQ Contact
LTC2875HS8#PBF - 60V Fault-Protected CAN Transceiver | ADI
LTC2875HS8#PBF

LTC2875HS8#PBF - 60V Fault-Protected CAN Transceiver | ADI

The Analog Devices LTC2875HS8#PBF is a robust, high-speed, low-power CAN (Controller Area Network) transceiver that operates from a 3.3V or 5V supply and features ±60V overvoltage fault protection on the bus pins during all modes of operation, including power-down. The device supports data rates up to 4 Mbps (CAN FD capable) and is housed in an 8-pin SOIC (HS8) package. Per the Analog Devices LTC2875 datasheet, the part is intended for 3.3V or 5V CAN networks requiring tolerance to large common-mode transients such as load-dump events in 12V/24V automotive or industrial systems. What is a CAN transceiver? A CAN transceiver is an interface IC that sits between a CAN protocol controller (typically a microcontroller) and the physical differential two-wire CAN bus (CANH/CANL). It converts the controller's CMOS/TTL TX/RX logic into the differential dominant/recessive signaling required by ISO 11898-2/ISO 11898-5, providing ESD and overvoltage robustness, common-mode rejection, and the bus-level protection that the controller itself cannot supply. The LTC2875 belongs to the interface IC -> transceiver IC -> CAN bus transceiver category inside the broader CAN bus driver / CAN FD transceiver family. Key features include ±60V bus fault protection, ±25kV ESD (HBM) on the CANH/CANL pins, ISO 11898-2 and ISO 11898-5 conformance, low current shutdown mode, SPLIT pin for recessive stabilization, and a wide supply range of 3V to 5.5V. The driver output stage is internally slew-rate limited and guarantees VSYM (driver symmetry) so the part can be used in CAN FD frames up to 4 Mbps. The LTC2875 combines an NPN/PNP bipolar bus driver with a precision differential receiver and a charge-pump-assisted protection rail that clamps bus voltages above and below the supply rails. The integrated ±60V fault path is active even in shutdown and power-off states, an important differentiator versus conventional CAN transceivers that lose protection when VCC collapses. Typical applications include automotive body and chassis ECUs, industrial CAN nodes with long cabling exposed to 24V/48V supply transients, building automation and HVAC CAN networks, and any 3.3V or 5V MCU-based system that must survive miswiring or load-dump events on the bus. When designing with this part, place 100nF supply decoupling as close as possible to VCC and add TVS diodes (or use the part's integrated ±60V clamp) to guarantee fault survival. The SPLIT pin typically requires a 10kΩ/1nF RC network to ground for proper recessive-bias stabilization per the datasheet typical application circuit. This page synthesizes distributor pricing, drop-in 8-SO alternatives, and practical fault-protection design notes that are not collected in any single manufacturer datasheet, helping engineers select, source, and lay out the LTC2875HS8#PBF with confidence.

RFQ Contact
LTC485MJ8 - Low-Power RS485 Transceiver | Analog Devices
LTC485MJ8

LTC485MJ8 - Low-Power RS485 Transceiver | Analog Devices

The Analog Devices LTC485MJ8 is a low-power, half-duplex differential bus transceiver for RS485 multipoint networks and RS422 systems, supplied from a single 5 V source and offered in an 8-pin CERDIP package. Its key characteristics include 1.8 mA typical supply current, ±10 kV ESD protection, 28 ns typical driver propagation delay, 4 ns driver skew, and an extended common-mode range extending from +12 V to -7 V. An RS485 transceiver is an interface integrated circuit that combines a differential line driver and differential receiver on one chip. It converts logic-level signals into balanced bus voltages and converts differential bus signals back into receiver-compatible logic. This electrical layer sits beneath protocols such as Modbus and sits above the physical RS485 bus, where it improves noise immunity and allows multiple nodes to communicate over longer distances than an unbalanced single-ended interface. The LTC485 family uses CMOS circuitry to reduce power consumption while preserving ruggedness against overload and ESD damage. Its half-duplex arrangement means the bus driver and receiver share the same differential pair, so software or hardware must control the transmit-enable signal to prevent simultaneous driving and receiving. The driver is designed for low propagation delay and controlled skew, while the extended common-mode range helps the device remain operational when ground-potential differences exist between connected systems. According to the Analog Devices LTC485 product documentation, the device also meets RS422 requirements. The 1.8 mA typical operating current is valuable in distributed bus nodes that may operate from limited power budgets. Typical driver propagation delay is 28 ns with 4 ns skew, making the interface suitable for control networks, instrumentation links, industrial monitoring equipment, and factory-automation systems where deterministic timing and bus fault tolerance are important. Typical implementations place the LTC485MJ8 between a host UART or microprocessor and a twisted-pair bus. A typical node includes local decoupling, a termination resistor at each physical end of the bus, biasing resistors to establish a fail-safe idle state, and protection appropriate to the installation environment. The transceiver should be connected to the interface ground with a controlled return path, especially when distant devices can develop ground-potential offsets. Designers must verify the board footprint and pin assignments before substitution, particularly when moving between ceramic, plastic, and surface-mount LTC485 variants. Decoupling capacitors should be placed directly beside the supply and ground pins, while the differential route should remain short and appropriately terminated. The principal trade-off is the manual half-duplex direction control, which reduces component count but requires the controller to manage turnaround timing. This page consolidates the device function, electrical limits, application guidance, package details, lifecycle information, and verified drop-in alternatives into an engineering-focused reference for evaluating the LTC485MJ8 in RS485 and RS422 interface designs.

RFQ Contact
LTC486ISW - Quad RS485 Driver, 5V, 16-SOIC | Analog Devices
LTC486ISW

LTC486ISW - Quad RS485 Driver, 5V, 16-SOIC | Analog Devices

Analog Devices LTC486ISW is a quad low-power differential bus and line driver designed for RS485 and RS422 multipoint data transmission. The device operates from a single 5 V supply, supports a bus common-mode range from -7 V to +12 V, and is packaged in a 16-pin SOIC. Each channel provides differential driver outputs with three-state operation for shared-bus systems. An RS485 driver is a physical-layer interface component that converts a digital logic signal into a balanced differential signal suitable for reliable communication over long or electrically noisy cables. It belongs to the interface IC hierarchy, alongside RS422 line drivers, transceivers, and isolators. Balanced differential signaling improves common-mode noise rejection and enables multiple devices to share a bus when their outputs are tri-stated. The LTC486 uses a low-power CMOS implementation with a typical supply current of 110 µA. It meets RS485 and RS422 applications, supports extended common-mode operation, and provides three-state outputs for multipoint networks. Its ruggedness against overload and electrostatic-discharge damage makes it suitable for industrial equipment where driver outputs may encounter noisy or fault-prone bus wiring. The four independent channels reduce the component count on systems that require multiple communication links, instrumentation buses, or distributed I/O. Thermal shutdown protects the device if an output is accidentally shorted to a supply or low-impedance source. Depending on the fault condition, the manufacturer notes that up to 250 mA can flow through the affected output before shutdown behavior intervenes. Typical uses include industrial measurement systems, instrumentation buses, data acquisition equipment, factory automation interfaces, and embedded control systems. The LTC486 is especially useful where multiple nodes must share one bus and only one transmitter should be active at a time. Its extended common-mode range can improve interoperability in systems using longer cables or grounds at different potentials. PCB design should keep the driver close to the bus connector, provide a solid ground-plane connection, and include appropriate protection against external transients. Verify output rise and fall times, bus loading, cable length, termination, and grounding before treating a laboratory connection as production-ready. The 16-pin SOIC also leaves adequate board area for routing and surge-protection components. This product page combines the LTC486 family specifications with orderable package information, focused application guidance, design checks, and verified same-footprint alternatives. It helps engineers distinguish the basic LTC486ISW ordering code from lead-free and tape-and-reel production variants without overlooking common-mode, thermal, and bus-integration constraints.

RFQ Contact
LTC6078IDD - Dual CMOS R2R Op Amp, 25µV Vos | Analog Devices
LTC6078IDD

LTC6078IDD - Dual CMOS R2R Op Amp, 25µV Vos | Analog Devices

The Analog Devices LTC6078IDD is a dual-channel, micropower precision CMOS operational amplifier that delivers rail-to-rail input and output swing in a 10-lead DFN (3 mm × 3 mm) package. It combines a trimmed 25 µV maximum input offset voltage, a 0.7 µV/°C maximum offset drift, and a 750 kHz gain-bandwidth product while consuming only 0.55 mA of quiescent supply current per amplifier. The CMOS input stage draws less than 50 pA of bias current, making the part suitable for high-impedance sensor front-ends. Background: an operational amplifier (op amp) is a DC-coupled, high-gain electronic voltage amplifier with differential inputs and, typically, a single-ended output. Rail-to-rail (R2R) op amps are a specialized class whose input common-mode range and output voltage swing can approach both supply rails, allowing designers to maximize dynamic range in low-voltage single-supply systems. Within the analog signal chain hierarchy, the LTC6078IDD sits between sensors/transducers and ADC input buffers, conditioning millivolt-level signals before digitization. The LTC6078IDD features a slew rate of 0.05 V/µs, 113 dB open-loop gain (typical), 13 nV/√Hz input voltage noise density at 1 kHz, and 1.5 mA output drive capability. It operates from a single 2.5 V to ±5 V supply (4 V to 18 V total) and is fully specified over the -40 °C to +85 °C industrial temperature range. The DFN-10 (DD) package exposes a thermal pad that lowers junction-to-ambient thermal resistance. The architecture combines a precision input chopper-stabilized front-end with a class AB output stage, eliminating the crossover distortion common to R2R designs. This dual-stage topology gives the part its rare combination of sub-25 µV offset, sub-50 pA bias current, and rail-to-rail swing - parameters that historically required trade-offs. Typical applications include battery-powered instrumentation, precision sensor signal conditioning (thermocouples, strain gauges, pH probes), medical instrumentation, A/D converter input buffers, and handheld test equipment. The low 0.55 mA/amp supply current also makes it useful for solar-powered remote sensor nodes. When designing with the LTC6078IDD, the exposed pad (pin 11) must be soldered to the PCB ground plane for thermal dissipation and rated input common-mode performance. Designers should keep input traces short and guarded when amplifying microvolt-level signals. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
LTC6226HS6#TRMPBF - 420MHz, 1nV/√Hz Low-Noise Op Amp | ADI
LTC6226HS6#TRMPBF

LTC6226HS6#TRMPBF - 420MHz, 1nV/√Hz Low-Noise Op Amp | ADI

The Analog Devices LTC6226HS6#TRMPBF is a very fast, low-noise, rail-to-rail output, unity-gain-stable single operational amplifier housed in a 6-pin TSOT-23 (S6) package. It delivers a gain-bandwidth product of 420 MHz, a slew rate of 180 V/μs, and an ultra-low input-referred voltage noise of 1 nV/√Hz, with distortion below -90 dBc for 4 V_P_P signals at 1 MHz. The HS6 suffix indicates the -40°C to +125°C automotive/extended-industrial operating temperature grade, while the #TRMPBF suffix denotes a 500-unit mini-reel Pb-free tape-and-reel package. A rail-to-rail output operational amplifier (RRIO op amp) is an analog IC whose output voltage can swing within millivolts of both supply rails, maximizing dynamic range in low-voltage single-supply systems. Op amps belong to the broader hierarchy of linear integrated circuits → amplifiers → operational amplifiers → high-speed amplifiers → low-noise precision amplifiers, and they sit inside the power management and signal-chain families of any mixed-signal system. This category matters because every sensor, ADC, DAC, and reference buffer ultimately depends on a clean, fast op amp to translate real-world signals into usable voltages. Key differentiators of the LTC6226HS6 include its 1 nV/√Hz input noise density (among the lowest for GBW > 400 MHz devices), 180 V/μs slew rate that enables 1 MHz large-signal operation, and -90 dBc SFDR at 1 MHz for 4 V_P_P outputs, making it a benchmark for high-dynamic-range signal chains. The combination of unity-gain stability, rail-to-rail output swing, and 420 MHz GBW in a TSOT-23-6 footprint is unusual: most competing parts sacrifice either bandwidth, noise, or output swing. Typical applications include 16-bit and 18-bit ADC input buffers, transimpedance amplifiers (TIAs) for photodiodes and ultrasound, high-speed line drivers, active filters, and precision instrumentation front-ends where low noise and high linearity coexist. The 5.5 mA quiescent supply current is acceptable for these performance levels. The TSOT-23-6 footprint allows the LTC6226 to drop directly onto boards originally laid out for the LTC6252 family. When designing with this part, ensure the load is referenced to ground within the output swing range and place a 0.1 μF X7R decoupling capacitor within 5 mm of the supply pin to preserve PSRR. The shutdown pin (SHDN) lets you reduce quiescent current to microamp levels during standby, which is valuable in battery-powered test equipment. This page synthesizes distributor pricing from DigiKey and Mouser, cross-reference alternatives verified against the Analog Devices LTC6226/6227 datasheet, and engineering design notes that complement the manufacturer application information.

RFQ Contact
LTC6226IDC - 420MHz GBW Low Noise RRIO Op Amp | ADI
LTC6226IDC

LTC6226IDC - 420MHz GBW Low Noise RRIO Op Amp | ADI

The Analog Devices LTC6226IDC is a very fast, low-noise, rail-to-rail output, unity-gain stable single operational amplifier with a gain-bandwidth product of 420MHz and a slew rate of 180V/us, packaged in a 6-lead DFN (2mm x 2mm) with exposed pad. The input-referred voltage noise is just 1nV/sqrt(Hz) and harmonic distortion is below -90dBc for 4Vp-p signals at 1MHz. What is an op amp? An operational amplifier is a high-gain DC-coupled analog building block used in signal conditioning, filtering, and feedback loops. Rail-to-rail output (RRIO) op amps extend the output swing to within millivolts of either supply rail, maximizing dynamic range on low-voltage supplies. The LTC6226 belongs to the precision/high-speed amplifier sub-family, which sits between general-purpose op amps and fully-dedicated high-speed current-feedback amplifiers in the analog IC hierarchy. Key features of the LTC6226IDC include 420MHz gain-bandwidth product, 180V/us slew rate, 1nV/sqrt(Hz) input voltage noise density, less than -90dBc THD at 1MHz/4Vp-p, rail-to-rail output swing, and unity-gain stability. The part runs from a 2.8V to 11.75V total supply (or +/-1.4V to +/-5.875V dual) and draws approximately 5.5mA of quiescent current. The exposed-pad DFN-6 package keeps the thermal resistance low for continuous high-output-current operation. The internal architecture uses a complementary bipolar input stage followed by a rail-to-rail class-AB output stage. The very low input noise density makes the LTC6226IDC well suited for photodiode transimpedance amplifiers and ultrasound front-ends where the signal-to-noise ratio is dominated by the front-end amplifier's own voltage noise rather than its current noise. Typical applications for the LTC6226IDC include 16-bit to 20-bit ADC drivers, photodiode transimpedance amplifiers, ultrasound preamplifiers, active filters, video line drivers, and low-noise instrumentation front-ends. The combination of low noise, high GBW, and rail-to-rail output makes it a strong fit for single-supply industrial data-acquisition systems. When designing with this op amp, decouple the supply pins with a 0.1uF X7R ceramic capacitor placed as close as possible to the V+ and V- pins, plus a bulk 10uF tantalum or ceramic capacitor. The exposed pad must be soldered to a copper pour to keep junction temperature within datasheet limits at high output swing and high load current. This page consolidates distributor pricing, drop-in alternatives, and practical design notes that are not always easy to find in the manufacturer datasheet.

RFQ Contact
LTC6226IS6#TRMPBF - 420MHz Low-Noise Rail-to-Rail Op-Amp | ADI
LTC6226IS6#TRMPBF

LTC6226IS6#TRMPBF - 420MHz Low-Noise Rail-to-Rail Op-Amp | ADI

The Analog Devices LTC6226IS6#TRMPBF is a very fast, low-noise, rail-to-rail output, unity-gain stable single operational amplifier housed in a 6-pin TSOT-23 (S6) package. It delivers a gain-bandwidth product of 420 MHz, a slew rate of 180 V/us, and an input-referred voltage noise of 1 nV/root-Hz, achieving distortion below -90 dBc for 4 Vp-p signals at 1 MHz. The device is specified for single or dual supply operation from 2.5 V to 11.75 V (or +/-1.25 V to +/-5.875 V). An operational amplifier (op-amp) is a high-gain DC-coupled analog building block used to amplify, buffer, filter, or condition voltage signals. Within the broader signal chain hierarchy, the LTC6226 belongs to the high-speed, low-noise precision amplifier category: op-amp -> high-speed amplifier -> precision amplifier -> analog IC -> integrated circuit -> semiconductor. Rail-to-rail output extends usable dynamic range to within millivolts of either supply rail, maximizing SNR in low-voltage systems. Key features include 1 nV/root-Hz input voltage noise density (industry-leading for a 420 MHz GBW device), 180 V/us slew rate for fast large-signal settling, 100 us startup time, and 1 mA typical supply current per amplifier. The TSOT-23-6 footprint enables dense PCB layouts while preserving the bandwidth needed for video, RF IF, and high-speed data-acquisition front ends. CMOS input bias current minimizes source-loading errors versus traditional bipolar parts. The architecture combines a low-noise input stage with a rail-to-rail output stage and internal compensation for unity-gain stability without external components. The wide supply range simplifies integration into 3.3 V, 5 V, +/-5 V, and +/-10 V analog rails, and the 180 V/us slew rate preserves signal integrity on fast pulses such as transimpedance photodiode amplifiers driving SAR ADCs at full Nyquist. Typical applications include high-speed photodiode transimpedance amplifiers, ADC drivers for 16- to 20-bit precision converters, active filters, video line drivers, RF/IF signal conditioning, and high-impedance sensor front ends. The 1 nV/root-Hz noise floor makes the LTC6226 especially suited where downstream SNR cannot tolerate amplifier-induced hiss. When designing with this part, observe the absolute-maximum supply of 12 V and ensure input common-mode range covers the full rail-to-rail output swing. Decouple supplies with a 0.1 uF X7R ceramic placed within 2 mm of the V+ and V- pins to preserve phase margin. The TSOT-23 thermal pad is pin 4 (GND); route a continuous ground pour beneath the part for best RF behavior. This page synthesizes distributor pricing, drop-in same-package alternatives, parametric comparisons, and practical design notes not found in the standalone manufacturer datasheet, helping engineers select the right high-speed amplifier variant.

RFQ Contact
LTC6247IKC - Dual 180MHz RRIO Op Amp | Analog Devices
LTC6247IKC

LTC6247IKC - Dual 180MHz RRIO Op Amp | Analog Devices

The Analog Devices LTC6247IKC is a dual-channel, 180 MHz gain-bandwidth, unity-gain stable operational amplifier with rail-to-rail input and output swings, packaged in an 8-pin UTDFN (2x2 mm) with an exposed pad. The part consumes only 1 mA of supply current per amplifier while delivering a 90 V/us slew rate and a low 4.2 nV/rt-Hz input-referred voltage noise density. An operational amplifier (op amp) is a high-gain DC-coupled analog building block that uses negative feedback to amplify, buffer, filter, or condition analog signals. The LTC6247 family sits in the broader taxonomy: op amp -> amplifier IC -> analog signal chain -> semiconductor. Rail-to-rail input/output (RRIO) op amps extend the usable input common-mode and output swing range to within millivolts of both supply rails, which is critical in low-supvoltage single-supply designs (2.5 V, 3.3 V, 5 V) where every millivolt of headroom matters. Key differentiating features of the LTC6247 include 180 MHz GBW, 90 V/us slew rate, 4.2 nV/rt-Hz input noise, unity-gain stability, 1 mA quiescent current per amplifier, and a shutdown-pin option (MS10/DFN) that drops the amplifier into a 42 uA standby state. The 8-pin UTDFN exposed pad provides a low theta-JA path for the 1 mA quiescent plus dynamic load dissipation. Architecturally, the LTC6247 uses a complementary N-channel/P-channel input stage that supports true rail-to-rail common-mode sensing, followed by a class-AB output stage optimized for RRIO swing. The wide GBW at low quiescent current is the result of ADI's process tuning that maximizes ft/Iq efficiency. Combined with low input bias current and rail-to-rail operation, the part suits photodiode transimpedance, active filtering, and ADC driver roles. Typical applications include active filters, photodiode transimpedance amplifiers, ADC drivers for SAR and delta-sigma converters, portable instrumentation front ends, and reference buffers. The shutdown pin enables low-power duty cycling in battery-powered systems. When designing with the LTC6247IKC, pay attention to the exposed thermal pad: it must be soldered to the PCB ground plane to achieve rated thermal performance and to provide the lowest-impedance return for high-frequency load currents. Decouple each supply pin with a 0.1 uF ceramic placed within 3 mm of the pin. This page synthesizes distributor pricing, drop-in UTDFN-8 alternatives, and practical layout notes not aggregated on the manufacturer product page.

RFQ Contact
LTC6363HMS8-2#PBF - Precision Low Power Diff Amp | Analog Devices
LTC6363HMS8-2#PBF

LTC6363HMS8-2#PBF - Precision Low Power Diff Amp | Analog Devices

The LTC6363HMS8-2#PBF is a precision, low power, fully differential amplifier with rail-to-rail outputs, optimized to drive SAR ADCs. It is part of the LTC6363 family from Analog Devices, which includes standalone and fixed-gain versions. This specific variant, the LTC6363-2, features internal matched resistors to provide a fixed gain of 2V/V, eliminating the need for external resistor networks and ensuring accurate, ultrastable gain with excellent CMRR. The device operates from a single 2.8V to 11V supply or dual ±1.4V to ±5.5V supplies, and offers a 35 MHz -3dB bandwidth and a 500 MHz gain bandwidth product. With a high slew rate of 75V/µs and a low input bias current of 100 nA, it is well-suited for high-speed, high-resolution data acquisition systems. A fully differential amplifier (FDA) is a type of operational amplifier that has differential inputs and differential outputs, providing a balanced signal path that rejects common-mode noise and doubles the output voltage swing compared to single-ended amplifiers. FDAs are essential in modern signal chains, particularly for driving high-performance analog-to-digital converters (ADCs), where they convert single-ended signals to differential, provide gain, and buffer the ADC input. The LTC6363 family sits within the hierarchy of differential amplifiers, which are a subset of operational amplifiers, which in turn are part of the broader category of linear integrated circuits. This hierarchy is fundamental to understanding the role of the LTC6363 in precision signal conditioning. Key features of the LTC6363HMS8-2#PBF include its fixed gain of 2V/V with precision laser-trimmed on-chip resistors, which provide a DC CMRR of 100dB, equivalent to using 0.0005% tolerance resistors. The device also features a shutdown pin for power saving, rail-to-rail outputs, and a low power consumption of typically 1.1mA. The input offset voltage is typically 50µV, and the input bias current is 100nA. The amplifier is specified over the -40°C to 125°C temperature range (H-grade) and is available in an 8-pin MSOP package. Technically, the LTC6363-2 uses a precision architecture that includes internal matched resistors, ensuring accurate gain without external components. This design reduces board space and component count, while improving reliability and performance. The device's high slew rate and bandwidth make it suitable for driving SAR ADCs with sampling rates up to 500kSPS or more, depending on the ADC. The rail-to-rail output stage allows the amplifier to swing close to the supply rails, maximizing the dynamic range of the ADC. Typical applications include driving SAR ADCs in industrial process control, medical instrumentation, and data acquisition systems. The LTC6363-2 is also used in communication systems, such as base stations and software-defined radios, where it conditions signals before digitization. Its low power and precision make it ideal for battery-powered portable instruments. When designing with the LTC6363HMS8-2#PBF, ensure proper power supply decoupling with 0.1µF and 10µF capacitors close to the V+ and V- pins. The VOCM pin sets the output common-mode voltage, which should be matched to the ADC's reference voltage for optimal performance. The shutdown pin can be used to reduce power consumption when the amplifier is not in use.

RFQ Contact
LTC6406IMS8E - 3 GHz Differential Amplifier | Analog Devices
LTC6406IMS8E

LTC6406IMS8E - 3 GHz Differential Amplifier | Analog Devices

The Analog Devices LTC6406IMS8E is a 3 GHz, low-noise, fully differential amplifier/driver optimized for 3 V single-supply operation, with rail-to-rail differential inputs and an adjustable output common-mode voltage through the VOCM pin. The verified source identifies an 8-lead MSOP package and describes the device as an ADC-driver/data-acquisition amplifier. Its differential architecture supports low-noise signal conditioning where preserving common-mode control and differential balance is important. A fully differential amplifier is an active signal-conditioning circuit that amplifies the difference between two input voltages while providing differential outputs. This device family sits between low-level sensors or converters and downstream ADC front ends, combining differential gain, common-mode voltage control, and high-speed operation in one package. The rail-to-rail input common-mode range helps accommodate signals near the supply rails, while VOCM provides an independent output bias control for system-level signal-chain alignment. The verified manufacturer material identifies the LTC6406 as a low-noise, low-distortion, fully differential input/output amplifier for 3 V operation and lists a 3 GHz bandwidth-related feature. Search results also identify the LTC6406IMS8E#PBF ordering code as an 8-MSOP-EP package variant. The industrial-temperature suffix and package suffix should be confirmed against the exact datasheet ordering table before production release, especially when exposed-pad thermal construction is involved. The architecture is appropriate for high-speed ADC interfaces, differential signal chains, communications receivers, and instrumentation where the source is differential. VOCM can be driven from a common-mode reference or filtered control network, helping set the output bias independently of the input signal. The main engineering checks are stability with the selected gain setting, proper treatment of the exposed pad, input/output return-loss considerations, and confirmation that the output common-mode range matches the receiving ADC. Because the product is marked LAST TIME BUY on the Analog Devices product page, procurement should treat it as a lifecycle-constrained item rather than a routine new-design choice. Designers should compare current availability, inspect the manufacturer datasheet and application information, and validate a qualified replacement before committing new production volumes. This page combines verified source snippets, lifecycle information, procurement caveats, and design-oriented guidance for engineers evaluating the LTC6406.

RFQ Contact
LTC6702HDC#PBF - Tiny Micropower Dual Comparator | Analog Devices
LTC6702HDC#PBF

LTC6702HDC#PBF - Tiny Micropower Dual Comparator | Analog Devices

The Analog Devices LTC6702HDC#PBF is a tiny micropower, low-voltage dual comparator supplied in an 8-lead DFN (2x2 mm) package with exposed pad, delivering rail-to-rail CMOS/TTL push-pull outputs. The two comparators operate from a single 1.7 V to 5.5 V supply, draw only microamps of quiescent current, and feature a typical propagation delay of 500 ns over the full temperature range. A comparator is an analog building block that compares two input voltages and switches its output to logic high or low depending on which input is larger. Dual comparators integrate two independent comparators on a single die, which lowers board area, BOM cost, and channel-to-channel delay mismatch in window detectors, threshold sensors, and clock-recovery circuits. Within the broader signal-chain hierarchy, the LTC6702HDC#PBF sits inside the amplifier/comparator product family, which itself belongs to the data-conversion and analog-frontend tier of a power-management and signal-conditioning system. Key features include an input offset voltage of 3.5 mV maximum at 3 V supply, rail-to-rail input common-mode range that extends beyond both supply rails, push-pull CMOS/TTL-compatible outputs that eliminate the need for an external pull-up resistor, and a low quiescent current optimized for battery-powered applications. Internal hysteresis is provided to prevent output chatter in noisy environments, and the inputs tolerate transients beyond the supply rails without latch-up. The device uses a CMOS process with a precision input stage and a fast decision stage, achieving 500 ns typical response time while keeping total supply current in the microamp range. This combination of speed and low power is unusual and stems from Analog Devices' bias-current scaling technique that adjusts the input-stage current in proportion to the input transition rate, conserving power during static DC conditions. Typical applications include battery-powered window comparators, threshold detectors and discriminators, clock regeneration in low-power oscillators, automotive sensing and control modules, and general-purpose signal conditioning where two comparators are needed on the same supply rail. Designers often use the LTC6702HDC#PBF in Li-ion powered products where its 1.7 V minimum supply allows operation directly from a single discharged battery cell. When laying out the PCB, connect the exposed pad to a low-impedance ground plane to minimize thermal resistance and provide a stable reference for the input stage. Place supply bypass capacitors as close as possible to the V+ pin to avoid supply ringing during fast output transitions. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that are not provided together on the official manufacturer datasheet. Engineers can use the comparison table and FAQ below to evaluate second-source options and to plan decoupling, layout, and battery-life trade-offs in one place.

RFQ Contact
LTC6702HDC#TRMPBF - Tiny Dual Comparator, 5.5V | Analog Devices
LTC6702HDC#TRMPBF

LTC6702HDC#TRMPBF - Tiny Dual Comparator, 5.5V | Analog Devices

The Analog Devices LTC6702HDC#TRMPBF is a tiny micropower, low-voltage dual comparator designed to maximize battery life while providing both speed and low-voltage operation in space-constrained applications. The device delivers rail-to-rail CMOS/TTL push-pull outputs, operates from a 1.7V to 5.5V single supply, and is housed in an 8-pin DFN (2 mm x 2 mm) exposed-pad package. According to the Analog Devices datasheet (document 6702fa), the part is built on a small-footprint platform intended for handheld and battery-powered products. A comparator is an analog building block that compares two input voltages and produces a digital output indicating which input is larger. The LTC6702HDC integrates two independent comparators with internal hysteresis, rail-to-rail input common-mode range, and complementary push-pull output stages capable of driving CMOS or TTL logic loads directly without external pull-up resistors. The part sits within the broader power-management hierarchy: voltage monitor -> comparator -> analog building block -> mixed-signal IC -> semiconductor. Key features of the LTC6702HDC include a 500 ns typical propagation delay, 32 uA typical quiescent current per comparator (microampere-class power consumption), 65 dB common-mode rejection, and an operating temperature range of -40 C to +125 C. The dual-comparator topology allows window comparators, dual-threshold battery monitors, and zero-crossing detectors in a single chip. The push-pull output eliminates the static current draw of open-drain comparators through external pull-ups, an important consideration for battery life. Architecturally, the LTC6702 uses a low-power CMOS input stage with a fast decision latch and CMOS/TTL-compatible output drivers, achieving a balance between quiescent current and edge speed that simpler micropower comparators cannot match. The exposed die-pad package provides a low thermal-resistance path, important when both comparators switch simultaneously at high toggling rates. Designers benefit from the lack of requirement for a separate reference rail. Typical applications include low-battery detection in single-cell Li-ion and 2x/3x AA-powered portable electronics, window comparators for power-good monitoring in 1.8V/3.3V rails, level translation between analog signals and 1.8V GPIO domains, multichannel sensor threshold detection in IoT endpoints, and zero-crossing detectors in audio or motor control. The 8-pin DFN package fits beneath QFNs and 8-pin MSOP footprints on most boards. Designers should note that the LTC6702HDC's H grade suffix denotes the -40 C to +125 C automotive/industrial temperature range; pin-compatible C-grade (0 C to +70 C) and I-grade (-40 C to +85 C) variants are available in the same DFN-8 footprint. Decoupling of the supply pin with a 0.1 uF ceramic capacitor placed within 2 mm of the V+ pin is recommended for stable comparator operation. This page synthesizes Analog Devices datasheet parameters, distributor availability, and drop-in alternatives within the LTC6702 family not always presented together on single-source distributor pages.

RFQ Contact
LTC6752HSC6-4 - 280MHz, 2.9ns Comparator, SC-70-6 | Analog Devices
LTC6752HSC6-4

LTC6752HSC6-4 - 280MHz, 2.9ns Comparator, SC-70-6 | Analog Devices

The Analog Devices LTC6752HSC6-4 is a single high-speed comparator from the LTC6752 family capable of toggle rates up to 280 MHz and featuring a 2.9 ns propagation delay with 1.2 ns rise/fall times. Housed in a 6-pin SC-70 (SOT-23-6 equivalent footprint) package with a separate input and output supply, this CMOS-output comparator offers rail-to-rail inputs and supports single-supply operation. The HS suffix indicates the high-speed tier with separate VIN and VOUT rails, and the -4 designator selects the SC-70-6 package option. A comparator is an analog building block that compares two input voltages and produces a digital logic output indicating which input is larger. Comparators are foundational to high-speed signal chains: they convert analog waveforms (sine, triangular, photodiode current pulses) into clean logic-level transitions that downstream counters, ADCs, or FPGAs can time-stamp. Within the broader power management and signal chain taxonomy, a high-speed comparator like the LTC6752 sits between analog sensors and digital decision logic, and its speed directly determines the timing accuracy of any system that uses it for threshold detection. Key specifications include 280 MHz toggle rate, 2.9 ns propagation delay (typical), 1.2 ns rise/fall times, rail-to-rail input common-mode range, CMOS output stage, separate VIN/VOUT supplies, and operating temperature range of -40 C to +125 C. According to the manufacturer datasheet, the part is recommended for new designs and operates from a 2.45 V to 5.25 V input supply. The CMOS output stage delivers clean logic levels and avoids the high input bias current of older bipolar comparators. The LTC6752 family includes 5 members differentiated by options such as separate input and output supplies, shutdown pin, output latch, adjustable hysteresis, and complementary outputs. The -4 package suffix selects the SC-70-6 footprint, the smallest in the family. The architecture focuses on low dispersion and stable propagation delay across input overdrive, making it well suited for time-critical applications. Typical applications include high-speed instrumentation, time-of-flight sensing, threshold detection in pulse circuits, clock and data recovery, motor control feedback, and clock buffer replacement in digital systems. The wide input range and CMOS output make it particularly valuable when an analog signal must be detected against a moving threshold. When designing with this device, place the decoupling capacitor as close to the supply pin as possible, keep input traces short to minimize parasitic capacitance, and account for the 2.9 ns propagation delay when calculating system timing margins. Latch and hysteresis options (where present in the family) improve noise immunity but trade off against maximum toggle rate. This page synthesizes distributor pricing, drop-in alternatives across the LTC6752 family, and practical high-speed layout guidance not found in the manufacturer datasheet alone.

RFQ Contact
LTC6754HUD - 1.8ns R2R LVDS Comparator | Analog Devices | QFN-12
LTC6754HUD

LTC6754HUD - 1.8ns R2R LVDS Comparator | Analog Devices | QFN-12

The Analog Devices LTC6754HUD#PBF is a high-speed rail-to-rail input comparator with LVDS-compatible outputs, housed in a 12-pin QFN (3x3) package with exposed thermal pad. It features 1.8 ns propagation delay, 1 ns of dispersion (10 mV to 125 mV overdrive), and a toggle rate up to 890 Mbps. The supply voltage range is 2.4 V to 5.25 V for both VCCI and VCCO rails, and the device operates across the -40 °C to +125 °C industrial temperature range. A high-speed comparator is an analog building block that compares two input voltages and produces a logic-level output indicating which input is larger, optimized for sub-nanosecond decision latency. Within the signal-chain hierarchy, comparators sit between operational amplifiers (continuous-time gain) and logic gates (sampled decision), and feed directly into high-speed ADCs, clock-data recovery blocks, and threshold-detection circuits. The LTC6754 belongs to the LVDS-output comparator family, which trades CMOS/TTL swing for low-noise differential signaling to minimize EMI and ground bounce in dense, multi-gigabit designs. Key features that distinguish the LTC6754 include its true rail-to-rail input stage that maintains linearity across the entire common-mode range, an integrated LVDS driver that produces a 350 mV differential swing into a 100 Ω termination, and a separate shutdown pin for power savings in duty-cycled applications. The exposed-pad QFN-12 (3x3 mm) package yields a thermal resistance of approximately 38 °C/W, sufficient for the modest power dissipation typical of a single-supply LVDS comparator (roughly 23 mA quiescent current). Architecturally, the LTC6754 uses a regenerative latch stage following a rail-to-rail input pre-amplifier, allowing both high-speed transitions and low-input-bias currents. The LVDS output stage complies with the ANSI/TIA/EIA-644-A standard, which enables direct connection to FPGAs and ASICs with built-in LVDS receivers without external level translation. Typical applications include high-speed instrumentation triggers, threshold detection in radar and LIDAR front-ends, clock-and-data recovery loops, satellite communication IF stages, and zero-crossing detectors in motor control. The LVDS output is especially valuable in noisy environments such as factory automation or automotive ECU test systems where single-ended CMOS would couple switching transients into sensitive analog paths. Designers should note that the VCCI and VCCO supplies can be tied to a single rail, but separating them allows the input stage to operate from one domain while the output swings into a different supply. Termination of the LVDS pair with a 100 Ω differential resistor close to the receiver is essential to prevent reflections at toggle rates above 500 Mbps. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the LTC6754HUD that complement the manufacturer datasheet with selection guidance and cross-references.

RFQ Contact
LTC6992IS6-1 - TimerBlox V-Controlled PWM, 3.81Hz-1MHz | ADI
LTC6992IS6-1

LTC6992IS6-1 - TimerBlox V-Controlled PWM, 3.81Hz-1MHz | ADI

The Analog Devices LTC6992IS6-1 is a silicon oscillator IC with analog voltage-controlled pulse width modulation (PWM) capability from the TimerBlox family, housed in a 6-pin TSOT-23 (S6) package. It operates over a wide output frequency range of 3.81 Hz to 1 MHz and accepts a single supply from 2.25 V to 5.5 V. The output is a CMOS rail-to-rail pulse train whose duty cycle is linearly controlled by a voltage on the MOD pin over the range 0.1·VSET to 0.9·VSET, clamped to 5%-95% outside that window. A silicon oscillator (a.k.a. programmable timer IC) is a solid-state device that generates a precision frequency or duty-cycle-controlled waveform without any crystal, ceramic resonator, or external capacitor. Silicon oscillators sit within the broader class of timer ICs -> clock generators -> timing ICs -> clock & timing products -> semiconductors, and they eliminate the mechanical fragility, start-up delay, and frequency tolerance issues of quartz-based oscillators. Key features include: a single resistor RSET programs the master frequency from 3.81 Hz to 1 MHz across four decades; the MOD pin accepts 0 V to 1 V to set duty cycle; ±15% frequency accuracy with no external trim; 1.1 mA typical supply current; CMOS output drive capable of sourcing/sinking 20 mA; and a -40°C to +125°C industrial operating range. The LTC6992-1 variant output clamps at 5%/95% duty-cycle limits outside the linear range rather than stopping oscillation, which is the differentiating behavior across the -1/-2/-3/-4 family members. Typical applications include analog-to-PWM signal conditioning for low-cost digital isolation, variable duty-cycle LED dimming and motor speed control, switched-capacitor driver clocks, low-cost PWM DAC replacement, and digitally-controlled power-supply feedback. Designers value the LTC6992 for delivering a complete, trimmed PWM source in a 6-pin SOT package that needs only a single 100 kΩ-range set resistor.

RFQ Contact