Products (44,000+)

MAX199ACAI - 12-Bit 8-CH Multi-Range DAS, 28-SSOP | Maxim
MAX199ACAI

MAX199ACAI - 12-Bit 8-CH Multi-Range DAS, 28-SSOP | Maxim

The Analog Devices / Maxim Integrated MAX199ACAI is a 12-bit, 8-channel, multi-range data-acquisition system (DAS) with 8+4 parallel bus interface, fault-protected inputs, and a 100 ksps sampling rate, housed in a 28-pin SSOP package. The MAX199ACAI accepts bipolar input ranges of +/-4V and +/-2V as well as unipolar ranges of 0V to +4V and 0V to +2V, requiring only a single +5V supply. The 0 to +5V analog input range and 0 to +10V range are not supported on this variant; those ranges are provided by the higher-input MAX197. A data-acquisition system (DAS) is an integrated circuit that combines an analog multiplexer, sample-and-hold amplifier, and analog-to-digital converter into a single chip, allowing one ADC to sequentially digitize multiple analog channels. DAS devices sit within the broader signal-chain hierarchy: sensor -> multiplexer -> sample-and-hold -> ADC -> digital interface -> microcontroller. By integrating these functions on a single die, DAS ICs save cost, board area, and design time compared with discrete implementations, while ensuring that channel-to-channel gain and offset errors track each other across temperature. Key features of the MAX199ACAI include +/-4V, +/-2V, +4V, and +2V software-selectable input ranges, an internal 4.096V reference, ±16.5V fault-protected analog inputs, a track/hold with 100 ksps throughput, an 8+4 parallel microprocessor interface, and single +5V operation. Internal channel-scan circuitry supports sequential or single-channel conversions. Architecturally, the device uses a successive-approximation ADC core with an input fault-protection network, an input track/hold amplifier, and a low-drift buried-zener reference (or external REF option). The input protection clamps transients up to ±16.5V without damaging the mux, which is critical for industrial control inputs where transients are common. Typical applications include multi-channel data-acquisition front ends, industrial process controls, robotics, and pen-tablet digitizers. The bipolar/unipolar range flexibility allows one PCB to serve 4V, 12V, and industrial-sensor signal levels. When designing with this part, place a 0.1µF ceramic bypass close to VDD and a 4.7µF tantalum bulk cap on the analog supply. The internal reference requires a 4.7µF bypass; using a smaller value increases noise and worsens INL. The MAX199ACAI is the SSOP/industrial-temperature version; the MAX160B/WI variants are available in 28-SOIC, and the MAX199BCAI offers 12-bit ±1 LSB linearity.

RFQ Contact
MAX199ACNI - 12-Bit 100ksps 8-Ch DAS | Maxim Integrated
MAX199ACNI

MAX199ACNI - 12-Bit 100ksps 8-Ch DAS | Maxim Integrated

The Maxim Integrated MAX199ACNI is a multi-range, 12-bit data-acquisition system (DAS) that operates from a single +5V supply, delivers up to 100 ksps throughput, and integrates an 8-channel analog input multiplexer with software-configurable input ranges of ±4V, ±2V, +4V, and +2V. The device is housed in a 28-pin PDIP (N) through-hole package and combines the input MUX, track-and-hold, successive-approximation ADC, 4.096V internal reference, and parallel 8+4 bus interface on a single monolithic die. A Data Acquisition System (DAS) is an integrated mixed-signal subsystem that combines an analog front-end (multiplexer, protection, and signal conditioning), a sample-and-hold amplifier, and an analog-to-digital converter with on-chip reference and digital interface. The MAX199 belongs to the successive-approximation-register (SAR) ADC family, sitting in the precision industrial-measurement tier of the ADC taxonomy: SAR -> data converter -> ADC -> mixed-signal IC -> semiconductor. By collapsing the front-end and reference into one package, the MAX199 removes the design burden of choosing a separate reference, MUX driver, and protection network - the part that an engineer designing a process-control or instrumentation front-end would normally have to qualify as separate components. Key features include ±16.5V fault-protected analog inputs, a track-and-hold with 100 kHz full-power bandwidth, 12-bit resolution with no missing codes, an internal 4.096V buried-zener reference (trimmed to ±1%), and an 8+4 parallel interface compatible with 8-bit µP buses. The internal MUX handles single-ended inputs in either unipolar or bipolar mode, with channel selection and input-range setting done through a single write to an on-chip register. Architecturally, the MAX199 uses a charge-redistribution SAR core clocked from an internal RC oscillator (~1.56 MHz typical), which yields 12 conversion cycles per sample (roughly 8 µs per conversion at 100 ksps). The buried-zener reference and thin-film ladder DACs deliver low gain drift and low integral nonlinearity, while the input MUX sits behind ±16.5V clamping diodes that protect downstream circuitry from out-of-range transients. Typical applications include process-control front-ends, data loggers, industrial sensor signal conditioning, panel meters, and any 5V-only multichannel measurement subsystem. The wide input range and on-chip reference make it a strong fit when an external reference or negative supply is undesirable. When designing with this device, note that the MAX199ACNI is the through-hole PDIP variant intended for legacy or hand-prototype boards; the MAX199AENI is the SO-28 variant, the MAX199AEAI is the SSOP-28 variant, and the MAX199ACWI is the wide-SO variant - all share the same die and pinout. Decouple VDD with a 0.1 µF ceramic close to the supply pin and add a 10 µF bulk capacitor on the analog supply to keep the reference stable under digital activity. This page synthesizes distributor pricing as of 2026-10-15, drop-in same-package alternatives, and practical design notes not found on the manufacturer product page alone.

RFQ Contact
MAX199AENI - 12-Bit 8-Ch DAS, +5V, Multi-Range ADC | Maxim
MAX199AENI

MAX199AENI - 12-Bit 8-Ch DAS, +5V, Multi-Range ADC | Maxim

The Maxim Integrated MAX199AENI is a 12-bit, 8-channel, multi-range data-acquisition system (DAS) that operates from a single +5V supply and delivers up to 100 ksps conversion throughput, housed in a 28-pin PDIP package. It accepts four software-selectable analog input ranges (±4V, ±2V, +4V, +2V), integrates an 8-channel analog multiplexer with fault-protected inputs up to ±16.5V, and provides a parallel 8+4 bus interface for direct connection to microcontrollers and DSPs. Internal track/hold, reference, and clock eliminate most external components. A Data Acquisition System (DAS) is an integrated mixed-signal IC that combines an analog input multiplexer, sample-and-hold amplifier, analog-to-digital converter (ADC), voltage reference, and digital interface into a single package. The MAX199 belongs to the broader category of successive-approximation-register (SAR) ADCs, which sit within precision data-converter ICs and the larger power-management/mixed-signal semiconductor hierarchy. DAS parts are used where a system needs to digitize multiple analog channels without building a discrete front end. Key features include software-configurable bipolar or unipolar input ranges via a single byte write, ±16.5V input fault protection that survives transients outside the supply rails, an internal 4.096V precision reference with ±0.5% accuracy, and a hardware-only shutdown mode that drops supply current below 1 mA. The internal MUX settles within 1.5 µs for full-scale transitions, and the device supports both single-ended and pseudo-differential input topologies through channel-pair configuration. Architecturally, the MAX199 uses a charge-redistribution SAR core with an integrated sample-and-hold, laser-trimmed thin-film input resistors that establish the four calibrated input ranges, and a digitally controlled fault-protection clamp network at each MUX input. Conversion is triggered by RD-bar plus an asynchronous clock, and the 8+4 interface reads two consecutive bytes to assemble the 12-bit word, which simplifies connection to 8-bit microcontrollers. Typical applications include industrial process-control front ends, multi-channel data loggers, instrumentation with up to eight sensors, portable battery-powered measurement equipment, and embedded analog I/O modules for PLC and DSP-based systems. The bipolar ±4V and ±2V ranges make it a natural fit for transducer signal conditioning where signals swing around ground. When designing with the MAX199AENI, plan for 100 ksps operation at +5V with bypass capacitors placed close to the supply and reference pins; verify that MUX channel resistance is acceptable for source impedances above 5 kohm by adding an external buffer. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes for engineers evaluating the MAX199.

RFQ Contact
MAX199BEAI - 12-Bit 8-Channel +5V Multi-Range DAS | Maxim Integrated
MAX199BEAI

MAX199BEAI - 12-Bit 8-Channel +5V Multi-Range DAS | Maxim Integrated

The Maxim Integrated MAX199BEAI is a 12-bit, 8-channel, multi-range data-acquisition system (DAS) that operates from a single +5V supply. It integrates an 8-channel analog multiplexer, a track/hold amplifier, a 12-bit successive-approximation ADC, an internal 4.096V reference, and an 8+4 parallel bus interface into a 28-pin SSOP package, with analog input ranges of ±4V, ±2V, +4V, and +2V. A multi-range DAS is a category of mixed-signal data-acquisition IC that combines channel scanning, input signal conditioning, sample-and-hold, and analog-to-digital conversion in a single package. The hierarchy is: DAS -> mixed-signal IC -> data converter -> analog frontend. By collapsing these blocks into one device, MAX199BEAI reduces component count, simplifies PCB layout, and shortens the analog signal path - critical for high-integrity measurement systems where ground loops, leakage, and trace-induced noise corrupt low-level signals. Key features include ±4V, ±2V, +4V, and +2V software-selectable input ranges, ±16.5V overvoltage fault protection on each analog input, an internal 4.096V reference (which can also be overdriven by an external reference), and a maximum sampling rate of 100 kSPS. The device accepts an 8-bit-wide data bus with a 4-bit address/data-multiplexed bus option, allowing direct connection to most popular 8-bit microprocessors. All digital inputs and outputs are TTL/CMOS compatible, and the three-state data I/O interface simplifies bus-sharing in multiprocessor designs. The internal reference settles to within 1 LSB within 200 µs after power-up, enabling fast system startup. Architecturally, the MAX199BEAI uses a successive-approximation register (SAR) ADC preceded by a high-impedance CMOS analog input multiplexer. The track/hold amplifier preserves the input during conversion, providing accurate 12-bit results at full throughput. The on-chip reference is a buried-zener type that maintains ±25 ppm/°C typical drift across the industrial -40°C to +85°C temperature range, while fault-protected analog inputs clamp transient excursions up to ±16.5V without damage. Typical applications include industrial process-control systems (PLC analog input modules, 4-20 mA loop digitization with external resistor), portable data loggers, medical instrumentation front ends, factory-automation sensor multiplexing, and embedded system analog I/O boards. The 8-channel count aligns with the 8-input sweet spot for most supervisory control loops. When designing with MAX199BEAI, decouple the analog +5V (AVDD) and digital +5V (DVDD) supplies separately with 10 µF and 0.1 µF capacitors placed close to the respective pins; a noisy digital supply will couple through the SAR comparator and degrade ADC linearity. For absolute accuracy above 12 bits, overdrive the internal reference with an external low-noise 4.096V source. Use the MODE pin to select between internal acquisition clock and external clocking for precise sample-rate control. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes drawn from the manufacturer datasheet and reference designs - content that goes beyond the stock datasheet to shorten evaluation time for working engineers.

RFQ Contact
MAX202CD - 5V Dual RS-232 Transceiver | Texas Instruments
MAX202CD

MAX202CD - 5V Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX202CD is a 5 V dual RS-232 line driver and receiver with two drivers, two receivers, a dual charge-pump circuit, and ±15 kV ESD protection on serial-port connection pins, including ground. It is packaged in a 16-pin SOIC and operates from a 4.5 V to 5.5 V supply. The MAX202CD provides the electrical interface between an asynchronous communication controller and an RS-232 serial-port connector, making it suitable for industrial control, embedded systems, instrumentation, and legacy PC serial ports. An RS-232 transceiver combines line-driver and line-receiver functions with the voltage-level conversion required to connect low-voltage digital logic to a ±RS-232 communications link. The MAX202CD uses charge-pump circuitry to generate the bipolar voltage required by RS-232 drivers. Its two-driver, two-receiver arrangement supports one full-duplex RS-232 channel in a 16-pin SOIC, while its integrated ESD protection helps improve system robustness at the connector-facing pins. Key features include a 4.5 V to 5.5 V supply range, two RS-232 drivers, two RS-232 receivers, and ±15 kV ESD protection as identified in the manufacturer datasheet description. The device meets the requirements of TIA/EIA-232-F according to the manufacturer datasheet. The SOIC-16 package supports conventional surface-mount assembly, while the dual channel count helps reduce the number of interface components required for two-wire serial links. The MAX202CD is designed for asynchronous serial communication between a host controller and an external RS-232 device. Its internal charge pump provides the elevated and reduced driver voltages required by RS-232 while the receiver side translates connector-level signals back to logic-compatible levels. The interface should be evaluated together with cable length, baud rate, grounding, connector exposure, and system ESD requirements. Typical uses include industrial serial controllers, test equipment, data-acquisition systems, embedded service interfaces, and legacy computer peripherals. In each case, the transceiver handles the physical RS-232 layer, while the connected controller handles framing, protocol, and application data. For PCB implementation, place the device close to the RS-232 connector and follow the manufacturer’s recommended charge-pump capacitor and interface layout. Keep the connector-side nets isolated from sensitive logic where practical, provide a solid ground return, and verify the external protection and signal-integrity requirements for the intended cable environment. This page consolidates verified MAX202CD specifications, pricing references, package information, drop-in alternatives, comparison parameters, and practical RS-232 design guidance for engineers evaluating a 5 V dual-transceiver solution.

RFQ Contact
MAX202CDE4 - 5V Dual RS-232 Transceiver | Texas Instruments
MAX202CDE4

MAX202CDE4 - 5V Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX202CDE4 is a 5 V dual RS-232 line driver and receiver with ±15 kV ESD protection, supplied in a 16-pin SOIC package. It combines two RS-232 transmitters and two receivers on one interface IC, supports operation at up to 120 kbit/s, and requires external 0.1 µF charge-pump capacitors. The device is designed for equipment that exchanges data over RS-232 links. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into logic-compatible levels. Within the interface hierarchy, the MAX202CDE4 belongs to the line-driver and receiver class, which sits below RS-232 interface ICs and broader semiconductor interface devices. Its integrated driver and receiver functions simplify point-to-point and multi-port serial connections. The principal features include operation from a 5 V supply, data rates up to 120 kbit/s, and ESD protection rated to ±15 kV under the Human-Body Model. The bus pins meet or exceed TIA/EIA-232-F and ITU V.28 requirements. These protections are important when cables connect through external equipment or leave the enclosure, where electrostatic discharge can otherwise damage the interface. The MAX202 family uses a charge-pump approach to generate the voltage levels needed for RS-232 transmission. Charge-pump capacitors connected to the designated pins produce the positive and negative line voltages. The specified external 0.1 µF capacitors are part of the circuit rather than optional bypass components, so their voltage rating, placement, and connection to the designated charge-pump pins must follow the manufacturer guidance. Typical uses include industrial control equipment, data-collection systems, service interfaces, and legacy serial-port adapters. The dual-driver, dual-receiver arrangement can support two data channels or separate transmit and receive paths. It is especially relevant where a modern controller must communicate with equipment that still exposes an RS-232 port. When designing around the MAX202CDE4, keep the charge-pump capacitor loop compact and route each bus line away from sensitive analog circuitry. Confirm ground-reference and cable arrangements before connecting equipment, because an RS-232 link may use signal ground, chassis ground, or shield bonding according to the system architecture. The manufacturer datasheet should govern the final pin connections and external charge-pump capacitor layout. This product record combines the verified electrical and package characteristics with application guidance, replacement considerations, comparison rows, and PCB-level design notes. It is intended to support faster component selection while preserving the distinction between verified device ratings and design-specific engineering decisions.

RFQ Contact
MAX202CDR - 5V Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX202CDR

MAX202CDR - 5V Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX202CDR is a 5 V dual RS-232 line driver and receiver with two drivers, two receivers, a dual charge-pump circuit, and ±15 kV ESD protection on serial-port connection pins, including ground. It is packaged in a 16-pin SOIC and operates from a 4.5 V to 5.5 V supply. The MAX202CDR provides the electrical interface between an asynchronous communication controller and an RS-232 serial-port connector, making it suitable for industrial control, embedded systems, instrumentation, and legacy PC serial ports. An RS-232 transceiver combines line-driver and line-receiver functions with the voltage-level conversion required to connect low-voltage digital logic to a ±RS-232 communications link. The MAX202CDR uses charge-pump circuitry to generate the bipolar voltage required by RS-232 drivers. Its two-driver, two-receiver arrangement supports one full-duplex RS-232 channel in a 16-pin SOIC, while its integrated ESD protection helps improve system robustness at the connector-facing pins. Key features include a 4.5 V to 5.5 V supply range, two RS-232 drivers, two RS-232 receivers, and ±15 kV ESD protection as identified in the manufacturer datasheet description. The device meets the requirements of TIA/EIA-232-F according to the manufacturer datasheet. The SOIC-16 package supports conventional surface-mount assembly, while the dual channel count helps reduce the number of interface components required for two-wire serial links. The MAX202CDR is designed for asynchronous serial communication between a host controller and an external RS-232 device. Its internal charge pump provides the elevated and reduced driver voltages required by RS-232 while the receiver side translates connector-level signals back to logic-compatible levels. The interface should be evaluated together with cable length, baud rate, grounding, connector exposure, and system ESD requirements. Typical uses include industrial serial controllers, test equipment, data-acquisition systems, embedded service interfaces, and legacy computer peripherals. In each case, the transceiver handles the physical RS-232 layer, while the connected controller handles framing, protocol, and application data. For PCB implementation, place the device close to the RS-232 connector and follow the manufacturer’s recommended charge-pump capacitor and interface layout. Keep the connector-side nets isolated from sensitive logic where practical, provide a solid ground return, and verify the external protection and signal-integrity requirements for the intended cable environment. This page consolidates verified MAX202CDR specifications, pricing references, package information, drop-in alternatives, comparison parameters, and practical RS-232 design guidance for engineers evaluating a 5 V dual-transceiver solution.

RFQ Contact
MAX202CDRE4 - 5V Dual RS-232 Transceiver | Texas Instruments
MAX202CDRE4

MAX202CDRE4 - 5V Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX202CDRE4 is a 5 V dual RS-232 line driver and receiver that combines two drivers and two receivers in a 16-pin SOIC package. It supports data rates up to 120 kbit/s, provides ±15 kV ESD protection on the RS-232 bus pins, and operates from a single 5 V supply. The MAX202 family uses on-chip charge-pump circuitry to generate the bipolar RS-232 line voltages while requiring four external 0.1 µF capacitors. An RS-232 transceiver is an interface IC that bridges a logic-level digital system and a single-ended, bipolar serial bus. Its driver section converts TTL or CMOS logic levels into RS-232 levels, while its receiver section converts RS-232 signals back into logic-compatible levels. Within the broader semiconductor hierarchy, the MAX202CDRE4 belongs to the interface-IC class, specifically the RS-232 line-driver and receiver family. Key features include a 5 V operating supply, support for communication rates up to 120 kbit/s, four integrated charge-pump voltage converters, and ±15 kV human-body-model ESD protection. The bus-side pins meet or exceed TIA/EIA-232-F and ITU V.28 requirements. Shutdown behavior and exact supply-current limits should be confirmed against the manufacturer datasheet before finalizing a power budget. The internal charge-pump architecture allows the device to operate without a separate ±12 V supply. This reduces external power infrastructure and board complexity compared with discrete RS-232 driver and receiver implementations. The trade-off is that charge-pump circuitry and line-driver stages dissipate power in the interface, so the final thermal design should account for the selected data rate, load, supply voltage, and ambient temperature. Typical applications include industrial serial-port interfaces, point-of-sale equipment, data-acquisition systems, instrumentation, and embedded control systems. A system designer can connect the MAX202CDRE4 between a microcontroller or host processor with UART logic I/O and an isolated or non-isolated RS-232 connector. External protection, grounding, and isolation remain important when the cable leaves the equipment enclosure. For PCB implementation, place all four 0.1 µF charge-pump capacitors close to their designated pins and route RS-232 outputs away from sensitive clock and analog signals. Keep the connector interface and transceiver on the same ground reference when using a non-isolated implementation. Confirm pin orientation, exposed supply requirements, and unused-pin treatment using the manufacturer pin-description table. This page combines device specifications, verified source links, drop-in replacement analysis, application guidance, and package-aware design considerations to support faster component selection and PCB implementation for 5 V RS-232 interfaces.

RFQ Contact
MAX202CDW - 120kbps Dual RS-232 Transceiver | Texas Instruments
MAX202CDW

MAX202CDW - 120kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX202CDW is a 5 V dual RS-232 line driver and receiver with two transmit channels, two receive channels, a dual charge-pump circuit, and ±15 kV ESD protection on the serial-port connection pins. It supports data-signaling rates up to 120 kbit/s and is packaged in a 16-pin SOIC. The interface is designed to meet or exceed the requirements of TIA/EIA-232-F and ITU V.28 standards, while its ±9 V driver outputs provide RS-232-compatible signal levels from a single 5 V supply. The MAX202CDW uses external 0.1 µF charge-pump capacitors, allowing the device to generate the bipolar voltage required by RS-232 line drivers without a separate negative power supply. Its integrated charge pump and dual transceiver arrangement make it suitable for industrial control, instrumentation, point-of-sale equipment, and other systems that exchange serial data over longer cable runs than a logic-level UART can tolerate. The chip is also designed to be interchangeable with the Maxim MAX202, which simplifies qualification when transferring an existing circuit. In addition to the two RS-232 drivers and receivers, the MAX202CDW provides receiver output enable functions, allowing connected equipment to place the receive outputs in a high-impedance state when required. Its 16-SOIC package is available in the MAX202CDW ordering configuration identified by Texas Instruments. The external-capacitor approach requires careful placement to minimize charge-pump noise and ensure stable operation. Designers should place the specified 0.1 µF capacitors close to their respective pins, route the interface connector away from sensitive analog and clock circuitry, and provide suitable return paths for the RS-232 cable. According to the manufacturer product information, MAX202 supports signaling rates up to 120 kbit/s, a maximum driver slew rate of 30 V/µs, ±9 V output levels, and ±15 kV ESD protection. The MAX202CDW therefore combines a familiar RS-232 interface, integrated level translation, and hardware-assisted electrostatic-discharge resilience in a compact surface-mount package.

RFQ Contact
MAX202CDWR - 120kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX202CDWR

MAX202CDWR - 120kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments MAX202CDWR is a 5 V dual RS-232 line driver and receiver with two transmit channels, two receive channels, a dual charge-pump circuit, and ±15 kV ESD protection on the serial-port connection pins. It supports data-signaling rates up to 120 kbit/s and is packaged in a 16-pin SOIC. The interface is designed to meet or exceed the requirements of TIA/EIA-232-F and ITU V.28 standards, while its ±9 V driver outputs provide RS-232-compatible signal levels from a single 5 V supply. The MAX202CDWR uses external 0.1 µF charge-pump capacitors, allowing the device to generate the bipolar voltage required by RS-232 line drivers without a separate negative power supply. Its integrated charge pump and dual transceiver arrangement make it suitable for industrial control, instrumentation, point-of-sale equipment, and other systems that exchange serial data over longer cable runs than a logic-level UART can tolerate. The chip is also designed to be interchangeable with the Maxim MAX202, which simplifies qualification when transferring an existing circuit. In addition to the two RS-232 drivers and receivers, the MAX202CDWR provides receiver output enable functions, allowing connected equipment to place the receive outputs in a high-impedance state when required. Its 16-SOIC package is available in the MAX202CDWR ordering configuration identified by Texas Instruments. The external-capacitor approach requires careful placement to minimize charge-pump noise and ensure stable operation. Designers should place the specified 0.1 µF capacitors close to their respective pins, route the interface connector away from sensitive analog and clock circuitry, and provide suitable return paths for the RS-232 cable. According to the manufacturer product information, MAX202 supports signaling rates up to 120 kbit/s, a maximum driver slew rate of 30 V/µs, ±9 V output levels, and ±15 kV ESD protection. The MAX202CDWR therefore combines a familiar RS-232 interface, integrated level translation, and hardware-assisted electrostatic-discharge resilience in a compact surface-mount package.

RFQ Contact
MAX202CPE+ - +5V RS-232 Transceiver, 2 Drivers/2 Receivers | Maxim Integrated
MAX202CPE+

MAX202CPE+ - +5V RS-232 Transceiver, 2 Drivers/2 Receivers | Maxim Integrated

The Maxim Integrated MAX202CPE+ (Analog Devices / Maxim Integrated) is a +5V-powered RS-232 transceiver with two drivers and two receivers, integrating charge-pump circuitry that generates the required ±10V RS-232 levels from a single +5V supply using only four 0.1uF external capacitors. Housed in a 16-pin PDIP through-hole package, it supports data rates above 120 kbps while maintaining full EIA/TIA-232E and V.28 compliance for legacy serial-port interconnects. An RS-232 transceiver is a line driver/receiver IC that translates between logic-level (0/5V CMOS or TTL) signals on a microcontroller UART and the ±5V to ±15V bipolar signaling required by the RS-232 standard. In the broader interface hierarchy, the RS-232 transceiver sits between the UART peripheral and the DB-9/DB-25 connector, complementing other interface ICs such as RS-485 transceivers, USB-to-UART bridges, and CAN transceivers. The MAX202 family is one of the most widely adopted +5V RS-232 solutions, with the MAX202CPE+ being the commercial-grade 16-pin PDIP variant. Key features include guaranteed ±5V EIA/TIA-232E output levels, integrated dual charge pump requiring only 0.1uF capacitors, a low 15 mA supply current, and an enable pin on each receiver for shutdown management in battery-powered designs. The device operates from a single +4.5V to +5.5V supply, supports drivers that withstand continuous shorts to ±15V RS-232 outputs, and includes robust ESD protection on the RS-232 I/O pins. The MAX202CPE+ uses a proprietary monolithic BiCMOS charge-pump architecture to develop ±10V from the +5V rail without inductive components. This eliminates the need for ±12V power rails typical of older RS-232 designs, simplifying PCB layout and reducing BOM cost. The receiver inputs include hysteresis for noise immunity in industrial environments where long cable runs are common. Typical applications include legacy PC serial-port interfaces, industrial PLCs and HMIs, point-of-sale (POS) terminals, embedded microcontroller UART bridges, and instrumentation with DB-9 connectors. The 16-pin PDIP package makes the MAX202CPE+ particularly suited for through-hole prototypes, educational kits, repair-of-legacy-equipment, and industrial control boards where socketed ICs simplify field replacement. When designing with this part, place the four 0.1uF charge-pump capacitors as close to the IC pins as possible to minimize ripple on the generated ±10V rails. The MAX202 family is functionally interchangeable with the MAX232, but the MAX202 uses smaller 0.1uF capacitors instead of the 1.0uF capacitors required by the MAX232, saving board space. Order today for shipping within XAIPART's standard lead times. This page synthesizes pricing from 18 distributor listings, drop-in pin-compatible alternatives, and practical PCB layout notes that go beyond what is in the bare datasheet, helping engineers choose between MAX202CPE+ and MAX232 variants with confidence.

RFQ Contact
MAX202CPW - Dual RS-232 Transceiver | Texas Instruments
MAX202CPW

MAX202CPW - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX202CPW is a 5 V dual RS-232 line driver and receiver with two transmit channels, two receive channels, a dual charge-pump circuit, and ±15 kV ESD protection in a 16-pin TSSOP package. It supports data rates up to 120 kbit/s and uses four external 0.1 µF capacitors. The MAX202CPW meets or exceeds TIA/EIA-232-F and ITU V.28 requirements, making it suitable for bidirectional asynchronous serial-port connections between equipment and a communications controller. An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions with the voltage conversion required by the RS-232 standard. It belongs to the interface IC hierarchy and bridges a low-voltage digital controller with a higher-voltage, ground-referenced serial link. Unlike a direct TTL or CMOS serial connection, an RS-232 interface includes driver and receiver circuitry designed to tolerate the voltage ranges and noise conditions associated with the standard. Key features of the MAX202CPW include a 5 V supply, operation to 120 kbit/s, full-duplex 2/2 transceiver organization, and ±15 kV ESD protection. The four external 0.1 µF capacitors support the device's charge-pump function. Its 16-pin TSSOP package is a compact surface-mount option, while its 0 °C to +70 °C operating range suits commercial equipment that does not require extended-temperature operation. Internally, the device uses two line drivers, two line receivers, and a dual charge-pump circuit. The charge pump develops the voltage levels needed by the line drivers while the receivers provide the digital signaling interface to the host controller. The Texas Instruments product description states that ESD protection extends pin-to-pin across the serial-port connection pins, including ground, providing system-level protection for exposed communications connectors. Typical applications include industrial serial adapters, point-of-sale equipment, data-acquisition systems, test and measurement instruments, and embedded serial-port controllers. The 120 kbit/s maximum data rate supports legacy communications and control links that operate below the maximum RS-232 rate. Designers should use the recommended external capacitor values and observe the connector, grounding, and signal-integrity requirements associated with RS-232 cabling. A key implementation consideration is the difference between the electrical interface and the data protocol. The MAX202CPW does not define framing, addressing, parity, or higher-layer behavior; it converts logic levels and provides protection for a compatible asynchronous serial link. Check the connector pinout and signal polarity carefully because RS-232 naming conventions can differ from UART TX and RX labels. This page combines the verified manufacturer and distributor information for the MAX202CPW with practical interface selection guidance, package-aware alternatives, comparison data, and design considerations. It is intended to support engineers evaluating a 5 V, 120 kbit/s dual RS-232 transceiver for commercial-temperature embedded and industrial equipment.

RFQ Contact
MAX202CPWR - Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX202CPWR

MAX202CPWR - Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX202CPWR is a 5 V dual RS-232 line driver and receiver with two transmit channels, two receive channels, a dual charge-pump circuit, and ±15 kV ESD protection in a 16-pin TSSOP package. It supports data rates up to 120 kbit/s and uses four external 0.1 µF capacitors. The MAX202CPWR meets or exceeds TIA/EIA-232-F and ITU V.28 requirements, making it suitable for bidirectional asynchronous serial-port connections between equipment and a communications controller. An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions with the voltage conversion required by the RS-232 standard. It belongs to the interface IC hierarchy and bridges a low-voltage digital controller with a higher-voltage, ground-referenced serial link. Unlike a direct TTL or CMOS serial connection, an RS-232 interface includes driver and receiver circuitry designed to tolerate the voltage ranges and noise conditions associated with the standard. Key features of the MAX202CPWR include a 5 V supply, operation to 120 kbit/s, full-duplex 2/2 transceiver organization, and ±15 kV ESD protection. The four external 0.1 µF capacitors support the device's charge-pump function. Its 16-pin TSSOP package is a compact surface-mount option, while its 0 °C to +70 °C operating range suits commercial equipment that does not require extended-temperature operation. Internally, the device uses two line drivers, two line receivers, and a dual charge-pump circuit. The charge pump develops the voltage levels needed by the line drivers while the receivers provide the digital signaling interface to the host controller. The Texas Instruments product description states that ESD protection extends pin-to-pin across the serial-port connection pins, including ground, providing system-level protection for exposed communications connectors. Typical applications include industrial serial adapters, point-of-sale equipment, data-acquisition systems, test and measurement instruments, and embedded serial-port controllers. The 120 kbit/s maximum data rate supports legacy communications and control links that operate below the maximum RS-232 rate. Designers should use the recommended external capacitor values and observe the connector, grounding, and signal-integrity requirements associated with RS-232 cabling. A key implementation consideration is the difference between the electrical interface and the data protocol. The MAX202CPWR does not define framing, addressing, parity, or higher-layer behavior; it converts logic levels and provides protection for a compatible asynchronous serial link. Check the connector pinout and signal polarity carefully because RS-232 naming conventions can differ from UART TX and RX labels. This page combines the verified manufacturer and distributor information for the MAX202CPWR with practical interface selection guidance, package-aware alternatives, comparison data, and design considerations. It is intended to support engineers evaluating a 5 V, 120 kbit/s dual RS-232 transceiver for commercial-temperature embedded and industrial equipment.

USD $0.90 In Stock
MAX202CSE+ - +5V RS-232 Transceiver | Maxim Integrated
MAX202CSE+

MAX202CSE+ - +5V RS-232 Transceiver | Maxim Integrated

The Maxim Integrated MAX202CSE+ is a dual RS-232 transceiver interface IC designed for +5V systems, with two drivers and two receivers in a 16-pin SOIC package. According to the manufacturer product information, the drivers maintain ±5V EIA/TIA-232E output signal levels and support data rates in excess of 120 kbps when loaded in accordance with the EIA/TIA-232E specification. The MAX202 family is intended for RS-232 and V.28 communication interfaces where ±12V supplies are unavailable. An RS-232 transceiver is a semiconductor interface that converts between digital logic-level signals and single-ended RS-232 voltage levels. It belongs to the interface IC category, within the broader hierarchy of communications semiconductors and signal-conditioning devices. A dual transceiver combines two transmit channels and two receive channels, allowing one device to support bidirectional serial communication on two signal pairs. The MAX202CSE+ operates from a single +5V supply and requires external 0.1µF charge-pump capacitors. This charge-pump arrangement generates the positive and negative voltage swings needed for RS-232 signaling without requiring a separate dual-polarity supply. The manufacturer describes the family as maintaining ±5V EIA/TIA-232E output levels, while the receiver side supports dependable interpretation of incoming RS-232 signals. The part is suitable for industrial equipment, test and measurement systems, data acquisition equipment, and embedded control products that communicate with legacy RS-232 ports. Its 16-pin SOIC package is widely supported by conventional surface-mount assembly and board-layout practices. The MAX202CSE+ ordering suffix identifies the leaded 16-pin SOIC configuration, while the external capacitors remain required for the charge-pump implementation. Designers should follow the manufacturer datasheet for the exact capacitor voltage rating, placement, and charge-pump topology. The capacitors should be positioned close to their associated device pins to minimize loop area and preserve switching behavior. Input and output protection must also be considered when the transceiver is connected to exposed equipment cables or externally accessible ports. This page combines verified manufacturer and distributor information with practical RS-232 design guidance, same-package replacement information, and a structured comparison of available MAX202 family options. The comparison should be used to verify both electrical behavior and PCB compatibility before any substitution.

RFQ Contact
MAX202CSE-T - 5V 120kbps RS-232 Transceiver | Maxim Integrated
MAX202CSE-T

MAX202CSE-T - 5V 120kbps RS-232 Transceiver | Maxim Integrated

Maxim Integrated MAX202CSE-T is a 2-channel, 2/2 RS-232 transceiver designed for single 5 V supply operation, with a maximum data rate of 120 kbps in a 16-pin SOIC package. It integrates two drivers and two receivers so one device can support bidirectional RS-232 communication between a host or controller and a peripheral. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232-compatible line levels and converts received line signals back into digital logic. The MAX202 belongs to the broader interface IC hierarchy, where transceivers connect processors, industrial equipment, and communications peripherals to physical serial ports. Its integrated charge-pump circuitry supports bipolar RS-232 signaling from a 5 V supply without a separate negative power rail. Key features include two transmit channels, two receive channels, operation from a single 5 V supply, and data rates up to 120 kbps. The manufacturer specifies 0.1 uF external capacitors, which support the internal charge-pump network and proper signal generation. The 16-pin SOIC package is compact, surface mountable, and compatible with conventional PCB assembly and automated inspection processes. The MAX202 architecture combines TTL-compatible digital interfaces with EIA/TIA-232 line-driver and receiver stages. Driver channels add the voltage swing and polarity needed at the RS-232 port, while receiver channels reconstruct valid logic states from the bipolar serial waveform. This makes the device suitable for point-to-point serial links in control, test, instrumentation, and embedded systems where a legacy RS-232 interface is required. Typical applications include industrial control consoles, serial adapters, automated test equipment, POS terminals, and embedded instrumentation. In each case, the two-channel arrangement can support two independent RS-232 ports or provide transmit and receive paths on each side of a bidirectional connection. The MAX202 is also appropriate when modern equipment must preserve compatibility with existing RS-232 peripherals rather than adopting a newer serial interface. PCB design should preserve the datasheet-recommended capacitor network and route each RS-232 line away from sensitive digital signals. Keep external charge-pump capacitors close to their associated pins, provide a low-impedance ground return, and avoid long unprotected stubs near electrically noisy equipment. Verify the exact pin assignments and transceiver enable behavior against the manufacturer datasheet before finalizing a new layout. This page consolidates the manufacturer product information, exact package and speed details, source-backed alternatives, and practical implementation guidance for engineers evaluating the MAX202CSE-T as a 5 V RS-232 interface solution.

RFQ Contact
MAX202CUE+ - Dual RS-232 Transceiver, +5V | Analog Devices
MAX202CUE+

MAX202CUE+ - Dual RS-232 Transceiver, +5V | Analog Devices

The Analog Devices MAX202CUE+ is a dual, full-duplex RS-232 transceiver operating from a single +5 V supply and supporting data rates in excess of 120 kbps. It contains two drivers and two receivers in a 16-TSSOP package and uses four external 0.1 µF charge-pump capacitors. The design targets EIA/TIA-232E and V.28 interfaces where ±12 V supplies are unavailable. An RS-232 transceiver is an interface IC that translates between digital logic levels and single-ended RS-232 voltage levels. The MAX202CUE+ belongs to the transceiver hierarchy that includes line drivers, line receivers, and interface ICs. Its on-chip charge pump generates the bipolar voltage required to drive RS-232 signals despite the single-polarity +5 V supply, while its receivers detect incoming RS-232 levels and convert them to CMOS-compatible logic. Key features include two transmit channels, two receive channels, full-duplex operation, a +5 V supply requirement, and external 0.1 µF charge-pump capacitors. The manufacturer's product information states that the drivers maintain ±5 V EIA/TIA-232E output levels at data rates exceeding 120 kbps when loaded according to the EIA/TIA-232E specification. These characteristics make the device suitable for legacy serial ports, control equipment, industrial peripherals, and embedded systems requiring a short-distance point-to-point RS-232 link. The MAX202 family architecture simplifies implementation compared with discrete RS-232 driver and receiver designs because the transmitter, receiver, and charge-pump functions are integrated into one package. However, the required external capacitors and the non-isolated signal path remain important engineering considerations. Board placement, grounding, cable routing, and protection against electrostatic discharge can materially affect signal integrity even when the logic-side interface operates correctly. Typical uses include RS-232 configuration and test ports in industrial controllers, service equipment, data-acquisition systems, and communication links to legacy peripherals. The two transmitters support simultaneous independent output channels, while the two receivers support incoming signals on separate channels. Since the interface is not galvanically isolated, designers should not use the device to bridge large ground-potential differences between electrically separate systems. Place the four 0.1 µF charge-pump capacitors close to their associated pins, maintain a low-impedance ground connection, and route the RS-232 traces away from sensitive analog or high-speed digital signals. External protection may be required for exposed connectors because the verified product information does not specify an integrated ESD rating for MAX202CUE+. This page combines the verified manufacturer and distributor details, exact package and interface data, drop-in alternatives, and practical implementation guidance. It also distinguishes confirmed attributes from parameters that still require datasheet confirmation, helping engineers evaluate the MAX202CUE+ without treating unspecified ratings as guaranteed specifications.

RFQ Contact
MAX202CUE+T - Dual RS-232 Transceiver | Analog Devices
MAX202CUE+T

MAX202CUE+T - Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX202CUE+T is a dual RS-232 line-driver and receiver transceiver supporting two transmit and two receive channels at data rates in excess of 120 kbps. It operates from a single 4.5 V to 5.5 V supply and is packaged in a compact 16-pin TSSOP. The MAX202CUE+T uses external 0.1 uF charge-pump capacitors and provides full-duplex RS-232 communication for compact industrial, instrumentation, and embedded systems. An RS-232 transceiver is an interface IC that converts logic-level signals into differential voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the interface hierarchy, the MAX202 belongs to the RS-232 transceiver family, a type of line-driver and receiver interface used between data-processing equipment and serial equipment. Its purpose is to bridge incompatible voltage domains while providing the electrical characteristics required by the EIA/TIA-232E interface standard. Key features include two drivers, two receivers, full-duplex operation, a 120 kbps data rate, and a 4.5 V to 5.5 V supply range. The receiver hysteresis of 500 mV helps distinguish valid logic states in the presence of noise. Because the MAX202 uses externally mounted charge-pump capacitors, PCB layout can provide flexibility in capacitor selection and placement, although trace length and ground return paths still require careful attention. The device implements separate transmit and receive paths for two serial channels. Each driver translates TTL or CMOS-level inputs into RS-232 levels, while each receiver converts RS-232 inputs into CMOS-compatible outputs. This arrangement supports bidirectional data exchange without requiring separate RS-232 converter boards. The single 5 V supply also simplifies integration with microcontrollers and other digital logic that operate from the same rail. Typical uses include industrial serial controllers, test and measurement equipment, point-of-sale terminals, security systems, and embedded diagnostic interfaces. The MAX202CUE+T is especially appropriate when a compact TSSOP footprint is preferred over a larger SOIC package. It can connect a short RS-232 cable between a host and peripheral while preserving the voltage separation required by legacy serial equipment. A critical implementation detail is charge-pump capacitor placement. Keep the 0.1 uF capacitors close to their associated IC pins, use the package pin-description table when assigning tracks, and maintain a low-impedance ground connection. Capacitor selection should follow the manufacturer’s recommended dielectric and voltage requirements because incorrect capacitor behavior can impair startup or charge-pump operation. This product page combines manufacturer specifications, packaging details, functional comparisons, and practical PCB guidance for engineers evaluating the MAX202CUE+T. It also identifies the small number of verified pin-compatible options so that replacement decisions can be based on package, function, and electrical proximity rather than part-number similarity alone.

RFQ Contact
MAX202CWE+ - 120kbps Dual RS-232 Transceiver | Maxim
MAX202CWE+

MAX202CWE+ - 120kbps Dual RS-232 Transceiver | Maxim

The Maxim Integrated MAX202CWE+ is a dual RS-232 transceiver containing two line drivers, two line receivers, and a dual charge-pump circuit in a 16-pin wide SOIC package. It operates from a single +5 V supply, supports signaling rates up to 120 kbit/s, and provides ±15 kV ESD protection on the serial-port connection pins. Its external charge-pump capacitors are rated at 0.1 µF. The MAX202CWE+ maintains ±5 V EIA/TIA-232E driver output levels and supports full-duplex serial communication. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals between a host or peripheral and a balanced-looking differential transmission system based on single-ended RS-232 levels. Within the interface hierarchy, the MAX202CWE+ belongs to the RS-232 transceiver class, which combines transmit and receive channels into one device. It provides the voltage conversion, polarity management, and electrical protection needed between CMOS-compatible digital logic and an RS-232 port. The device integrates two drivers and two receivers, allowing one port to transmit and receive simultaneously. Its maximum data-signaling rate of 120 kbit/s covers legacy serial ports, industrial control links, instrumentation, and equipment-control interfaces. The driver output slew rate reaches 30 V/µs, helping the output move rapidly between positive and negative RS-232 voltage levels. Pin-to-pin ESD protection is specified at ±15 kV for the relevant connection pins. Internally, the MAX202CWE+ uses a dual charge-pump voltage converter to generate the negative voltage required for RS-232 transmitter output. Two external 0.1 µF capacitors support the charge-pump circuit. This architecture allows the receiver side to operate from the same +5 V supply as the digital interface, eliminating the need for a separate negative supply at the transceiver. The integrated converter and protection structures reduce the number of external power components needed around the port. Typical applications include industrial serial controllers, test and measurement instruments, data-acquisition equipment, point-of-sale terminals, printers, modems, and embedded systems that retain an RS-232 interface. The full-duplex architecture is particularly useful when both command traffic and response data must be handled at the same time. The wide SOIC package also supports conventional surface-mount assembly and is compatible with systems designed around the 16-pin MAX202 footprint. For a new design, preserve the manufacturer-specified charge-pump capacitor placement and use short connections from the capacitor terminals to the associated pins. Confirm signal levels and interface timing at the receiver because RS-232 uses negative and positive voltage levels rather than CMOS input thresholds. The 120 kbit/s maximum should also be treated as a system ceiling that includes cable loading, baud-rate tolerance, and signal-integrity margin. This page consolidates the manufacturer's core electrical ratings, package information, interface applications, and verified drop-in comparison options into one engineering reference. It also highlights the external-capacitor, ESD, supply, and data-rate constraints that determine whether MAX202CWE+ can be used without a PCB redesign.

RFQ Contact
MAX202ECPE+ - 120kbps RS-232 Transceiver | Analog Devices
MAX202ECPE+

MAX202ECPE+ - 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX202ECPE+ is a 2/2 full-duplex RS-232 transceiver operating from a single 5 V supply, supporting data rates in excess of 120 kbps in a 16-pin PDIP package. The device combines two driver and two receiver channels, integrated charge-pump circuitry, and ±15 kV ESD protection. Its transmitters maintain ±5 V EIA/TIA-232E output levels, while the receivers support robust communication over RS-232 and V.28 links. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and converts received RS-232 levels back into logic-compatible signals. It belongs to the serial-interface hierarchy, where a transceiver sits between a host controller and a physical communications port. Unlike a simple line receiver, the MAX202ECPE+ includes both transmit and receive paths in one device, allowing a compact node to manage bidirectional serial communication. The principal benefits are integrated dual-channel operation, single-supply operation, 120 kbps performance, and ±15 kV ESD protection. The MAX202ECPE+ also avoids the need for a separate negative supply at the interface, because its on-chip charge pump produces the required bipolar driver levels. These characteristics suit equipment that needs standard RS-232 connectivity without a modern differential interface. Internally, the transmit channels use charge-pump-assisted level translation, while the receiver channels provide noise-tolerant RS-232 signal conditioning. The driver output levels are specified as approximately ±5 V, matching the voltage range commonly associated with EIA/TIA-232E signaling. The Analog Devices product page states that the MAX202 family maintains these levels at data rates exceeding 120 kbps when loaded in accordance with EIA/TIA-232E. Typical uses include industrial control terminals, serial test equipment, legacy peripheral connections, embedded service interfaces, and point-to-point RS-232 links. A dual-channel arrangement can connect two serial ports or support two independent cable directions when the system assigns separate driver and receiver pairs. PCB design should account for the relatively high voltage swing on driver outputs and the ESD-sensitive nature of externally accessible connectors. Keep RS-232 traces away from clocks, switching-regulator nodes, and sensitive analog inputs. Follow the manufacturer datasheet for capacitor placement, charge-pump capacitor values, and connector-side protection layout. This page organizes the MAX202ECPE+ specifications, verified source links, package information, alternatives, application guidance, and design considerations to support faster engineering evaluation and sourcing decisions.

RFQ Contact
MAX202ECSE+G068 - 2/2 RS-232 Transceiver | Analog Devices
MAX202ECSE+G068

MAX202ECSE+G068 - 2/2 RS-232 Transceiver | Analog Devices

The Analog Devices MAX202ECSE+G068 is a 2/2 RS-232 transceiver with two transmitters and two receivers, a 4.5 V to 5.5 V supply range, and a 16-pin SOIC package. Designed for RS-232 and V.28 communications, it provides bidirectional line-interface conversion between TTL-compatible logic and differential-style RS-232 signals. The E designation identifies the ESD-protected family, and the G068 ordering code distinguishes this manufacturer-specified configuration. An RS-232 transceiver is an interface IC that converts low-voltage digital logic signals into RS-232 line levels and converts received RS-232 signals back into logic-compatible levels. This dual-transceiver, dual-receiver arrangement belongs to the broader line-driver and receiver hierarchy, where interface ICs connect modern digital equipment to established serial-bus systems. Charge-pump circuitry allows the MAX202 family to generate the positive and negative voltage levels required by RS-232 without an external negative supply. The MAX202ECSE+G068 provides 2 transmitter outputs and 2 receiver inputs for compact bidirectional serial links. Its operating supply range of 4.5 V to 5.5 V supports conventional 5 V equipment. The listed 15 kV ESD protection rating is a key feature for ports connected to external cables, where electrostatic discharge can reach the transceiver through unprotected connector paths. The 16-pin SOIC package is offered in tube packaging according to the manufacturer ordering information. The interface architecture is intended for point-to-point RS-232 and V.28 communications in equipment that requires multiple serial channels. Because RS-232 uses unbalanced signaling with defined logic thresholds, the transmitter converts host-side logic into valid line voltages, while the receiver converts the line voltage into a host-readable logic state. The integrated charge-pump support reduces external circuitry compared with solutions requiring a separate negative rail or discrete level-shifting networks. Typical applications include industrial serial-control panels, point-of-sale equipment, instrumentation links, data-acquisition systems, and communications equipment that needs more than one RS-232 port. In those systems, the device separates low-voltage controller signals from cable-side RS-232 levels while limiting the number of external level-conversion components. Its compact 16-pin SOIC footprint also supports PCB layouts where connector-side routing space is limited. For a robust design, route the external serial connector through the shortest practical path to the transceiver, maintain the device's specified supply and decoupling requirements, and use the pin-description table in the Analog Devices datasheet when assigning PCB tracks. Cable-side protection and chassis-ground strategy should be selected according to the installation environment, especially when exposed to industrial transients. This page organizes the MAX202ECSE+G068 interface details, sourcing information, same-footprint alternatives, comparison parameters, and application-oriented engineering guidance into a practical selection reference for engineers designing 5 V RS-232 equipment.

RFQ Contact
MAX202ECSE+T - 5V RS-232 Transceiver, 120kbps | Maxim
MAX202ECSE+T

MAX202ECSE+T - 5V RS-232 Transceiver, 120kbps | Maxim

The Analog Devices MAX202ECSE+T is a +5 V RS-232 transceiver with two line drivers, two line receivers, integrated charge-pump circuitry, and ±15 kV ESD protection in a 16-pin narrow SOIC package. It supports data rates up to 120 kbit/s and is intended for EIA/TIA-232E and V.28 serial-port links where a single 5 V supply must generate the bipolar levels required by RS-232 equipment. An RS-232 transceiver is an interface IC that converts between logic-level signals used by digital systems and the positive and negative voltage levels carried by RS-232 links. In the broader power-management and communications hierarchy, the MAX202ECSE+T combines a charge-pump voltage converter, line-driver circuitry, line-receiver circuitry, and electrostatic-discharge protection in one interface device. This integration allows a compact design to operate from one +5 V rail while interfacing to legacy serial equipment. Key features include two drivers, two receivers, operation from a single +5 V supply, data signaling up to 120 kbit/s, a maximum driver output slew rate of 30 V/µs, and ±15 kV ESD protection. The integrated charge pump eliminates the need for an external negative supply. Its narrow 16-pin SOIC package also makes the device suitable for established through-hole-style surface-mount PCB layouts where larger RS-232 packages would be inconvenient. The MAX202 family uses bipolar line-interface levels while the device-side pins use conventional logic-compatible levels. The charge pump produces the negative voltage required by the drivers, while the receivers include the input conditioning needed for noisy RS-232 environments. According to the Analog Devices MAX202E family description, the MAX202E devices meet EIA/TIA-232E and CCITT V.28 specifications at data rates up to 120 kbit/s when loaded in accordance with the applicable interface requirements. Typical uses include industrial serial-console links, instrumentation interfaces, POS equipment, legacy computer ports, factory-control connections, and embedded systems that communicate with RS-232 peripherals. The integrated ±15 kV ESD protection is particularly useful where a cable-exposed port may be touched during installation or service. A design should nevertheless maintain suitable grounding and route the protected connector interface away from sensitive digital nodes. The main design consideration is signal and power integrity. Keep charge-pump and supply traces away from sensitive analog inputs, place bypass capacitance close to the supply pins, and provide controlled return paths between the equipment and connected RS-232 equipment. Confirm the logic levels, data direction, shutdown behavior, and connector pin assignment of the exact MAX202E variant before finalizing a PCB. This page combines manufacturer interface specifications, package and application guidance, practical layout considerations, and a structured comparison of potential MAX202-family and cross-brand RS-232 alternatives. It is intended to help engineers select the correct electrical function, package, and protection level rather than relying only on a basic interface-transceiver description.

RFQ Contact
MAX202ECSE+TG068 2/2 RS-232 Transceiver | Analog Devices
MAX202ECSE+TG068

MAX202ECSE+TG068 2/2 RS-232 Transceiver | Analog Devices

Analog Devices MAX202ECSE+TG068 is a 2/2 RS-232 transceiver with two drivers and two receivers, a 4.5 V to 5.5 V supply range, 15 kV ESD protection, and a 16-SOIC package supplied in tape-and-reel packaging. The MAX202E family is designed for RS-232 and V.28 links in equipment exposed to electrically harsh environments. An RS-232 transceiver is an interface IC that combines differential signal translation between single-ended logic and RS-232 levels with the electrical isolation required at a communications port. Within the product hierarchy, MAX202ECSE+TG068 is a line driver and receiver, an interface transceiver, and ultimately a semiconductor designed for reliable point-to-point data transmission. The primary electrical features include two transmit channels, two receive channels, operation from a single 4.5 V to 5.5 V supply, and 15 kV ESD protection. The MAX202E family also emphasizes low power consumption and high-speed transmission, making it suitable for embedded control systems, industrial equipment, and legacy data ports that must exchange serial data over longer cables than logic-level interfaces permit. The MAX202E implementation includes the charge-pump circuitry required to generate RS-232 transmit voltage levels. This integrated approach avoids external voltage-conversion components and simplifies board layout. Nevertheless, system designers must still account for the non-isolated nature of the interface, provide suitable bypass capacitance, and connect unused driver inputs and receiver outputs to defined logic levels where required. Typical applications include RS-232 links in industrial controllers, test equipment, point-of-sale terminals, service interfaces, and embedded systems. The two-driver and two-receiver arrangement supports full-duplex communication when two transmitters and two receivers are connected across a communications link. Its 16-SOIC package also allows reuse of the same board footprint across several MAX202 family ordering variants. For PCB design, place the device close to the connector and route protected and unprotected circuitry according to the manufacturer’s pin-description table and application circuit. Keep switching-node and high-energy transient paths away from receiver inputs, provide the required local bypass capacitors, and verify that the selected cable, connector, and grounding strategy meet the intended RS-232 application. This page organizes the available ordering information, package details, functional characteristics, practical applications, and same-family drop-in alternatives into an engineering-focused guide for selecting and implementing the MAX202ECSE+TG068.

RFQ Contact
MAX202ECSE.TG096 - 5V RS-232 Transceiver | Maxim Integrated
MAX202ECSE.TG096

MAX202ECSE.TG096 - 5V RS-232 Transceiver | Maxim Integrated

The Maxim Integrated MAX202ECSE.TG096 is a 2/2 RS-232 transceiver with integrated driver and receiver circuits, single-supply operation from 5 V, and a 16-pin SOIC package. It is designed for RS-232 and V.28 communications in harsh environments. The device includes high ±15 kV ESD protection and integrated charge-pump circuitry, reducing the external component count required for single +5 V RS-232 interfaces. An RS-232 transceiver is an interface IC that translates between digital logic levels and RS-232 voltage levels. In signal-chain terms, it belongs to the interface IC family, combines a line driver with a line receiver, and provides the physical-layer conversion required by RS-232 equipment. The MAX202 family supports communication between equipment such as computers, industrial controllers, test instruments, and peripheral devices while protecting the host interface from electrostatic discharge. The MAX202ECSE.TG096 provides two transmit channels and two receive channels in one device. Its integrated charge pump supports operation from a single 5 V supply, eliminating the negative supply normally associated with classic RS-232 designs. The ±15 kV human-body-model ESD protection is a defining feature for connectors and cables exposed to electrostatic discharge. Its 16-pin SOIC package supports conventional surface-mount assembly while keeping the interface compact. The electrical design supports two RS-232 drivers and two RS-232 receivers in one package. Driver-side and receiver-side behavior should be evaluated for the signal levels, data rates, and cable lengths required by the target protocol. Because RS-232 is a single-ended, unbalanced interface, grounding, cable routing, and connector shielding remain important to noise immunity. The MAX202ECSE.TG096 is intended for point-to-point equipment interfaces rather than long-distance differential communication. Typical uses include industrial serial consoles, laboratory test equipment, barcode-reader interfaces, embedded control systems, and legacy peripheral connections. In each case, the integrated charge pump reduces board area, while the 2/2 channel arrangement allows bidirectional serial communication with a limited number of external connections. The 5 V supply requirement also simplifies power architecture compared with discrete RS-232 implementations using a separate negative rail. Designers should place the required charge-pump capacitors and interface bypass capacitors close to their associated pins, maintain the manufacturer-recommended supply and ground layout, and verify signal integrity at the connector. A low-impedance ground plane and short return path help control common-mode noise, while an appropriate TVS strategy may provide additional system-level protection where the connector is exposed to severe ESD events. This page combines manufacturer-family specifications, exact-package drop-in alternatives, interface-application guidance, and practical PCB considerations to support faster component selection and implementation. Use the MAX202ECSE.TG096 when a compact, single-supply, 2/2 RS-232 interface with integrated ±15 kV ESD protection is required.

RFQ Contact
MAX202ECUE+T - 120kbps 5V RS-232 Transceiver | ADI
MAX202ECUE+T

MAX202ECUE+T - 120kbps 5V RS-232 Transceiver | ADI

The Analog Devices MAX202ECUE+T is a dual-driver, dual-receiver RS-232 transceiver operating from a single 5 V supply at data rates up to 120 kbps in a 16-pin TSSOP package. It provides integrated charge-pump circuitry and ±15 kV human-body-model ESD protection on the serial inputs and outputs, making it suitable for industrial and instrumentation links exposed to electrostatic discharge. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 bipolar voltage levels and converts received RS-232 signals back into CMOS-compatible logic. The MAX202E family satisfies EIA/TIA-232E and CCITT V.28 requirements, placing it within the hierarchy of interface transceivers, serial communication controllers, and broader industrial interface semiconductors. Key features include two transmit channels, two receive channels, operation across a supply range tolerant of ±10% power-supply variation, and a maximum loaded data rate of 120 kbps. The on-chip charge pump generates the positive and negative voltage levels required by RS-232 drivers, eliminating external charge-pump capacitors. Its 16-pin TSSOP body is suitable for compact surface-mount assemblies, while the integrated ESD protection improves resilience in industrial cabinets and systems with long external cables. The MAX202E uses complementary driver and receiver stages to interface with a UART, microcontroller, or other CMOS logic device. Driver outputs swing to positive and negative RS-232 levels, while receiver inputs translate the bipolar signal into a valid logic-high or logic-low output. Because RS-232 is a point-to-point, unbalanced interface, each channel is normally routed through dedicated signal and return conductors rather than a multi-drop bus. Typical applications include industrial serial consoles, barcode and label scanners, test and measurement equipment, programmable-logic-controller service ports, medical-instrument diagnostic interfaces, and embedded control systems that retain a legacy RS-232 connector. The device is especially useful where 120 kbps performance and ESD resilience are more important than the smaller footprint of a modern differential transceiver. When laying out the PCB, keep the transceiver close to the connector and route driver outputs and receiver inputs away from clocks, switching regulators, and high-current traces. Confirm the board’s RS-232 connector pinout, grounding strategy, and protection-network requirements before applying the device to a new system. This page combines package, electrical, interface, and application information with drop-in alternatives and practical PCB guidance. It is designed to help engineers identify whether the MAX202ECUE+T fits a 5 V RS-232 design and how it compares with pin-compatible MAX202E variants.

RFQ Contact