Products (39,000+)

PAM8302A - 2.5W Filterless Class-D Mono Audio Amplifier | Diodes Incorporated
PAM8302A

PAM8302A - 2.5W Filterless Class-D Mono Audio Amplifier | Diodes Incorporated

The Diodes Incorporated PAM8302A is a 2.5 W filterless Class-D mono audio amplifier housed in an 8-pin MSOP package, with an additional SOP-8 option. Its CMOS architecture drives 4 ohm or 8 ohm speakers directly without low-pass output filters, saving PCB area and BOM cost while delivering high-quality, low-THD audio reproduction. An audio amplifier is an electronic integrated circuit that boosts a low-power audio input signal to a level capable of driving a loudspeaker or headphones. The Class-D topology uses pulse-width modulation (PWM) to switch the output transistors fully on or fully off, achieving much higher efficiency (typically >85%) than linear Class-AB amplifiers (typically <60%). Within the broader taxonomy, the PAM8302A sits in the audio amplifier IC category, a subset of amplifier ICs, which belong to the signal chain and power management product families. Filterless Class-D amplifiers are particularly valued in portable, battery-powered designs because they eliminate bulky LC output filter networks, reducing both board area and cost. Key specifications include a 2.5 W continuous output power into 4 ohm at 10% THD from a 5.5 V supply, low THD+N of 0.10% at 1 W into 8 ohm, a wide 2.0 V to 5.5 V supply range, integrated undervoltage lockout at 2.1 V, and a low shutdown current. The MSOP-8 (with thermal pad) footprint offers a compact 3.0 mm x 3.0 mm outline suitable for handheld devices, while the SOP-8 (PAM8302AADCR) variant serves designs requiring through-hole-compatible footprints. Built-in short-circuit protection and thermal shutdown further enhance robustness in consumer applications. The PAM8302A employs a fully-differential PWM modulator with proprietary filterless modulation, which eliminates the traditional LC reconstruction filter while maintaining acceptable EMI through controlled edge-rate switching and spread-spectrum techniques. The differential input topology also rejects common-mode noise from upstream audio DACs or PWM sources. Typical applications include portable Bluetooth speakers, handheld gaming consoles, alarm clocks, intercom systems, toys, and any cost-sensitive battery-powered device requiring moderate audio output. Designers frequently choose this part for retrofit audio upgrades in retro gaming hardware, single-board computers, and IoT devices where PCB area is at a premium. When designing with the PAM8302A, ensure adequate power supply bulk decoupling (typically 10 uF) close to the AVDD/PVDD pins to minimize THD. The SD pin (active-low shutdown) must be tied high for normal operation or controlled via a GPIO for power sequencing. Reserve sufficient copper pour on the exposed thermal pad to dissipate Class-D switching losses, especially at full 2.5 W output. This page synthesizes distributor pricing, verified drop-in alternatives, and application-specific design notes not found in the manufacturer datasheet alone, making it a practical engineering reference for sourcing and design.

RFQ Contact
PAM8403 - 3W Filterless Class-D Stereo Audio Amplifier | Diodes Incorporated
PAM8403

PAM8403 - 3W Filterless Class-D Stereo Audio Amplifier | Diodes Incorporated

The Diodes Incorporated PAM8403 is a 3 W filterless Class-D stereo audio amplifier delivered in a 16-pin SOP package, operating from a 2.5 V to 5.5 V single supply. Each channel delivers 3 W into a 4 ohm load at 10% THD+N with a 5 V power supply, while maintaining efficiency up to 90% thanks to the Class-D switching topology. The device integrates a bridge-tied load (BTL) output stage that removes the need for external LC low-pass filters on the speaker lines, saving PCB area and BOM cost in stereo and mono consumer audio designs. A Class-D audio amplifier is a switching amplifier topology that uses pulse-width modulation at a switching frequency far above the audio band to recreate the input waveform. Compared with Class-AB linear amplifiers, Class-D parts achieve much higher efficiency (often >85%), which reduces power dissipation in portable and battery-powered applications. The PAM8403 belongs to the audio amplifier IC family, which itself sits inside the broader amplifier IC and integrated circuit hierarchy used in consumer and prosumer audio products. Key features include low THD+N for high-quality sound reproduction, a typical 90% efficiency figure that extends battery life in portable applications, and integrated protection such as short-circuit and thermal shutdown. The shutdown pin (SD) can drive the amplifier into a low-current mute state, and the device also provides a noise-free power-up/power-down cycle that eliminates audible pops. Available only in the SOP-16 package, the part is aimed at compact stereo speaker implementations where board real estate is at a premium. Typical applications include LCD TV and monitor speaker drivers, portable and Bluetooth speaker enclosures, laptop docking stations, DVD and game console line outputs, and phone / speakerphone accessories. Its filterless architecture allows very short, direct PCB traces from the IC outputs to the speakers, simplifying the layout versus traditional Class-D solutions that need an LC reconstruction filter. When designing with the PAM8403, place the supply decoupling capacitors as close to the VDDP and VDDL pins as possible, use a ferrite bead on the speaker outputs if extra EMI suppression is required, and respect the maximum junction temperature rating to avoid thermal shutdown during sustained high-output conditions. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes that are not found in the standalone manufacturer datasheet PDF, including PCB layout and EMI considerations specific to filterless Class-D designs.

RFQ Contact
PC28F256P33TFE - 256Mb Parallel NOR Flash, 95ns, 64-LBGA | Micron
PC28F256P33TFE

PC28F256P33TFE - 256Mb Parallel NOR Flash, 95ns, 64-LBGA | Micron

The Micron PC28F256P33TFE is a 256-Mbit (16M x 16) parallel NOR Flash memory organized as CFI-compliant FLASH NOR (MLC), supplied in a 64-ball LBGA (11x13 mm, EasyBGA) surface-mount package. It operates from a single 2.3 V to 3.6 V supply, delivers 95 ns initial access time, and supports a 52 MHz synchronous burst clock frequency for high-throughput x16 code execution and data storage. A NOR Flash (Not-OR gate Flash) is a non-volatile memory technology that provides random read access at byte/word granularity and executes-in-place (XIP) directly from the array, distinguishing it from NAND Flash which requires block-level access and external ECC management. NOR Flash belongs to the hierarchy: NOR Flash -> non-volatile memory -> semiconductor memory -> integrated circuit. It is commonly used as boot ROM, firmware storage, and parameter backup where reliability and deterministic read latency outweigh cost-per-bit. Key features of the PC28F256P33TFE include top-boot block architecture, asynchronous and synchronous burst read modes, hardware write protection, and a deep power-down mode for battery-powered designs. The device provides 100K endurance cycles per sector and a 20-year data retention rating. Operating temperature spans -40C to +85C, qualifying it for industrial-grade embedded systems. The 64-ball EasyBGA package offers a small 11x13 mm footprint compatible with high-density PCB layouts. The PC28F256 family uses a 16-bit data bus and a multiplexed address/data interface. The top-boot configuration places the parameter and boot sectors at the lowest addresses, simplifying bootloader mapping in many embedded architectures. Synchronous burst reads deliver up to 52 MHz, enabling fast shadowing and execute-in-place performance comparable to older pSRAM. Typical applications include networking routers and switches, industrial PLCs and HMI controllers, automotive infotainment, medical instrumentation, set-top box firmware storage, and aerospace embedded controllers. In these systems the PC28F256P33TFE stores the operating system, configuration tables, and device firmware that must survive power cycles without reloading from external media. When designing with this part, derate the junction temperature using a 1 oz copper pour under the BGA, observe the 100 ms maximum erase and 4 s program timings for sector updates, and follow the JEDEC JESD22-A114 moisture sensitivity level handling. The original Micron part has been transferred to Alliance Memory, which now produces it as a long-term supply drop-in. This page synthesizes distributor pricing, parametric cross-references, and practical design notes for engineers evaluating the PC28F256P33TFE for both new designs and legacy board refresh cycles.

RFQ Contact
PC28F640P30BF65B - 64Mb Parallel NOR Flash, 52MHz, 64-EasyBGA | Micron
PC28F640P30BF65B

PC28F640P30BF65B - 64Mb Parallel NOR Flash, 52MHz, 64-EasyBGA | Micron

The Micron PC28F640P30BF65B is a 64-Mbit parallel NOR Flash memory IC organized as 4M x 16 with a 65 ns access time and 52 MHz synchronous burst read clock, housed in a 64-ball EasyBGA (10x13 mm) package. It operates from a single 1.7V to 2.0V VCC supply (with VCCQ tolerant up to 3.6V per the P30 family specification), making it a drop-in compatible member of the legacy Micron/Numonyx P30 parallel NOR family. A parallel NOR Flash (often called CFI NOR) is a non-volatile memory that maps random memory accesses onto a parallel address/data bus, giving true execute-in-place (XIP) capability. Unlike NAND, every byte is addressable and read latency is deterministic in tens of nanoseconds, so boot code, BIOS, and firmware can run directly from the array without shadowing into DRAM. Parallel NOR sits above asynchronous SRAM and below NAND in the memory hierarchy: lower density than NAND, far faster random access, and far more durable (typically 100K program/erase cycles per sector). Key features include a bottom-boot sector architecture (parameter and small boot blocks at low addresses, bulk array above), 65 ns initial access / 52 MHz burst read for fast sequential code execution, x16 data width with multiplexed address bus, hardware data protection via WP#/LOCK#, deep power-down to microamp-level standby, and a -40C to +85C industrial operating range. The P30 family is also known for an automotive grade option (-B suffix) and a self-encrypting drive variant in the 128 Mb member of the family. The architecture is a true 16-bit-wide NOR cell array with on-chip write state machine supporting chip/sector erase and single-word programming, freeing the host from toggling legacy Intel-command sequences. Programmable erase and program timing let the host trade throughput for in-system endurance. The 64-ball EasyBGA package (10x13 mm) provides a compact footprint with exposed die attach paddle for thermal dissipation during sustained writes or erases. Typical applications include automotive infotainment boot ROM, networking line cards running u-boot or VxWorks directly from flash, industrial PLC firmware storage, point-of-sale terminals, and any embedded design requiring deterministic read latency and high endurance. The bottom-boot layout favors systems that need a small, frequently-updated calibration block plus a large read-mostly code region. Designers should respect the 1.7-2.0V VCC window, place VCC/VCCQ decoupling within 5 mm of the balls, and observe tAVQV (address-to-output) timing. Because this part is supplied today primarily by Alliance Memory's Axcell franchise (Micron exit-NOR was completed earlier), confirm current lead time and lifecycle status at order entry. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found on a single manufacturer datasheet page.

RFQ Contact
PC28F640P30BF65B-TR - 64Mb Parallel NOR Flash, 52MHz | Micron
PC28F640P30BF65B-TR

PC28F640P30BF65B-TR - 64Mb Parallel NOR Flash, 52MHz | Micron

The Micron PC28F640P30BF65B-TR is a 64-Mbit (4M x 16) parallel NOR Flash memory device built on the P30-65nm Axcell process technology, supporting a 52 MHz synchronous burst read interface and packaged in a 64-ball EasyBGA (10x13 mm). It operates from a 1.7 V to 2.0 V VCC core supply with a separate 1.7 V to 3.6 V VCCQ I/O supply, and offers an asynchronous access time of 65 ns (also reported as 75 ns in some datasheet revisions). A NOR Flash (Not-OR, technically "Not AND" wired-OR array) is a non-volatile memory class that supports random read access at byte or word granularity and executes code directly from the array (execute-in-place, XIP). This positions NOR above serial NOR for high-bandwidth or random-latency-sensitive workloads such as boot ROM, FPGA configuration shadowing, and embedded firmware storage. NOR sits within the broader hierarchy: NOR Flash -> parallel NOR -> non-volatile memory -> memory ICs -> semiconductors. Key features include 64 Mb density, a bottom-boot 128-KB uniform plus 4-KB parameter block architecture, 52 MHz synchronous burst reads, and individual block locking with a one-time programmable (OTP) security region. The device supports a hardware RESET# pin plus a RST# configuration input, WP#/ACC high-voltage protection/unprotect, and configurable read-array, read-ID, read-status, erase, and program command sets. The P30 architecture implements a multiplexed Address/Status/Command interface on DQ[15:0] with separate chip-enable (CE#), output-enable (OE#), and write-enable (WE#) controls, plus a synchronous burst pin group (AVD#, ADV#, CLK, WAIT). Block erase and word program operations typically complete in 0.4 s and 100 us respectively, with a 100K endurance rating per block. Typical applications include networking line-card boot, industrial controller firmware storage, automotive infotainment boot ROM, point-of-sale terminals, printer firmware, and any embedded system requiring execute-in-place with deterministic read latency. The 64-ball EasyBGA footprint also suits small-form-factor PCB designs. When designing with this device, place VCC and VCCQ decoupling (0.1 uF and 1 uF ceramic) within 5 mm of the package balls, keep CE# transitions clean during burst reads, and avoid long parallel bus stubs above 50 mm to preserve the 52 MHz timing margin. This page synthesizes distributor stock, pricing tiers, drop-in alternatives, and design notes to complement the manufacturer datasheet.

RFQ Contact
PC9RS08KA2DWE - 8-Bit RS08 MCU, 2KB Flash, 10MHz | NXP
PC9RS08KA2DWE

PC9RS08KA2DWE - 8-Bit RS08 MCU, 2KB Flash, 10MHz | NXP

The NXP PC9RS08KA2DWE is an 8-bit RS08 microcontroller built around a streamlined S08 instruction set, offering 2KB of FLASH program memory, 63 bytes of RAM, and a 10MHz CPU core, all housed in an 8-pin SOIC (5.30mm / 0.209") package. The device operates from a single 1.8V to 5.5V supply and integrates 4 general-purpose I/O pins, an internal oscillator, and essential system-protection peripherals including Low Voltage Detect (LVD), Power-On Reset (POR), and a Watchdog Timer (WDT). An RS08 microcontroller is a derivative of Freescale/NXP's HCS08 architecture, designed as a cost- and code-density-optimized 8-bit core for high-volume, ultra-low-cost embedded applications. RS08 devices retain the C-friendly S08 instruction set while reducing core area, making them the smallest and lowest-power members of the Freescale 8-bit portfolio. RS08 microcontrollers belong to the broader category of microcontrollers (MCU), which sit within embedded controllers and are essential building blocks of modern electronic systems. Key features include a single voltage supply range of 1.8V to 5.5V, 4 I/O pins for compact sensor and switch interfaces, an internal oscillator that eliminates the need for an external crystal, and robust system protection through integrated LVD, POR, and WDT peripherals. The simplified S08 instruction set, augmented with the high-performance LDA, STA, and CLR instructions, delivers a balance of code density and execution speed for cost-sensitive designs. The RS08 core uses a Von Neumann architecture with a simplified instruction pipeline and a reduced register file versus the full S08 family, targeting ultra-low-power and pin-constrained applications. The 10MHz bus speed at 5V provides ample throughput for sensor sampling, switch debouncing, and simple state-machine control, while the FLASH memory supports in-application reprogramming for field updates. Typical applications include battery-powered household appliances, remote-control transmitters, LED lighting controllers, low-end toys and personal-care devices, simple sensor interfaces, and replacement of discrete logic in white goods. The wide 1.8V to 5.5V supply range and low pin count (8-SOIC) make it ideal for compact, single-cell or 3V/5V mains-derived designs. When designing with this device, ensure the operating voltage stays within the 1.8V to 5.5V range and that adequate decoupling (typically 100nF plus bulk capacitance) is placed near the supply pin. The 4 available I/O pins limit the design to minimalist interfaces such as a single switch input, an LED output, and a one-wire or UART communication channel. This page synthesizes distributor pricing, drop-in and footprint-compatible alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select and source the PC9RS08KA2DWE for new designs and legacy maintenance.

RFQ Contact
PC9RS08KA2PAE - 8-Bit RS08 MCU, 2KB Flash, 10MHz | NXP
PC9RS08KA2PAE

PC9RS08KA2PAE - 8-Bit RS08 MCU, 2KB Flash, 10MHz | NXP

The NXP PC9RS08KA2PAE is an 8-bit RS08 microcontroller featuring a simplified S08 instruction set with high-performance LDA, STA, and CLR extensions, 2KB (2K x 8) of on-chip FLASH program memory, 63 bytes of RAM, and an internal oscillator supporting up to 10MHz CPU operation. Housed in an 8-pin PDIP package (0.300 inch, 7.62mm body width), it provides four general-purpose I/O pins plus integrated peripherals including a low-voltage detector (LVD), power-on reset (POR), and a watchdog timer (WDT) for embedded safety. An RS08 microcontroller is a reduced-pin-count, low-cost derivative of the Freescale/NXP S08 family, optimized for cost-sensitive, space-constrained applications that need deterministic 8-bit performance without external components. Architecturally, an RS08 sits within the broader 8-bit MCU taxonomy: microcontroller -> embedded controller -> 8-bit MCU -> HCS08/RS08 family -> cost-optimized sub-family. The CPU core implements a streamlined S08 instruction set so legacy ColdFire/S08 code can be ported with minimal effort while the silicon footprint and BOM cost remain minimal. Key feature highlights include 2KB FLASH (in-system programmable), 63 bytes of RAM supporting a tiny memory model with single-byte direct addressing for the first 16 locations, an internal oscillator that eliminates the need for an external crystal in most designs, four GPIO pins multiplexed with peripheral functions, and shadow register support for fast context switching in interrupt service routines. The simplified instruction set retains ADD, SUB, INC, and DEC for tiny addressing mode, allowing C compilers and assembler code to generate compact binaries. Typical applications include low-cost consumer appliances, IR remote controls, single-chip sensor interfaces, LED lighting controllers, simple battery chargers, and any embedded product that needs an 8-bit brain with on-chip non-volatile memory and a small pin count. The integrated LVD and watchdog make it suitable for unattended or mains-powered equipment that must reset cleanly on brown-out events. When designing with the PC9RS08KA2PAE, ensure the supply rail stays within the device's Vcc/Vdd range and place a 0.1 uF decoupling capacitor as close as possible to pin 8 (Vdd). CodeWarrior for RS08 (now offered as NXP's free CodeWarrior for ColdFire+RS08) and P&E Multilink/Cyclone programmers are required for in-circuit development. As the part is marked Obsolete in distributor listings, designers of new products should plan for last-time-buy or consider NXP S08KA2 series successors.

RFQ Contact
PC9S08QE128CLH - 8-bit S08 MCU 128KB Flash 50MHz 64-LQFP | NXP
PC9S08QE128CLH

PC9S08QE128CLH - 8-bit S08 MCU 128KB Flash 50MHz 64-LQFP | NXP

The NXP PC9S08QE128CLH is an 8-bit S08 microcontroller IC delivering 50MHz CPU performance with 128KB (128K x 8) of embedded FLASH program memory, housed in a 64-pin LQFP (10x10 mm) package. This industrial-grade member of the S08 family integrates enhanced peripherals and is targeted at cost-sensitive embedded control designs requiring on-chip LCD driver support and multiple serial interfaces. An 8-bit microcontroller (MCU) is a microprocessor integrated with memory, peripherals, and I/O on a single die. Within the broader semiconductor taxonomy, an MCU belongs to the embedded processor category, which itself sits under the integrated circuit hierarchy. The 8-bit designation refers to the data bus width and ALU datapath; S08 is NXP's (formerly Freescale) 8-bit HCS08 family using a modified Harvard architecture and a CPU08 instruction set. Compared with 16-bit MCUs (e.g., S12) and 32-bit MCUs (e.g., ColdFire V1/Kinetis E), 8-bit S08 devices prioritise low cost, low power, and deterministic interrupt response for appliance, white-goods, and industrial-control use cases. Key features of the PC9S08QE128CLH include 128KB FLASH for firmware storage, on-chip RAM for working data, an integrated LCD driver (a defining feature of the QE sub-family), and a peripheral set that typically includes timers (TPM), ADC, I2C, SCI (UART), and SPI. The 50MHz bus clock supports fast instruction throughput for time-critical control loops. The 64-LQFP (10x10) package provides 64 gull-wing leads on a 0.5mm pitch, suitable for standard SMT reflow and easy hand-solder prototyping. ECCN EAR99 classification indicates export-friendly commercial control. Architecturally, the S08 core uses a 16-bit stack pointer with banked RAM access and an HCS08 instruction set that is source-compatible with the legacy HC08 family while adding additional addressing modes and a background debug mode (BDM) for non-intrusive in-circuit debugging. The QE128 sub-family is the largest memory-density and most peripheral-rich 8-bit S08 device, offering more I/O than the QE64 and QE96 variants. Typical applications include white goods and appliance control, HVAC thermostats and sensor front-ends, industrial metering and instrumentation, low-cost consumer devices with LCD user interfaces, and embedded control subsystems. The integrated LCD driver eliminates the need for an external LCD bias-generator chip, reducing BOM cost and PCB area in display-equipped designs. Designers should plan oscillator and decoupling layout early, route the LCD segment pins away from switching signals to minimise display contrast artefacts, and follow the Freescale/NXP BDM pinout for in-circuit debug connection. Choosing the 64-LQFP variant over smaller QFP packages aids thermal dissipation and simplifies prototype rework. This page synthesises distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, including AEC-Q grade comparisons and package trade-offs for migration within the S08QE128 family.

RFQ Contact
PCA82C251T - 24V CAN Transceiver, 1MBd, SOIC-8 | NXP
PCA82C251T

PCA82C251T - 24V CAN Transceiver, 1MBd, SOIC-8 | NXP

The NXP PCA82C251T is a legacy CAN (Controller Area Network) bus transceiver that serves as the physical interface between a CAN protocol controller and the differential CAN bus, operating at data rates up to 1 MBd in 24V automotive and industrial systems. Housed in an 8-pin SOIC (SO-8) surface-mount package, it provides differential transmit capability to the bus and differential receive capability to the CAN controller, with full conformance to the ISO 11898-24V standard for 24V systems used in trucks, buses, and heavy industrial vehicles. A CAN transceiver is a physical-layer (PHY) device that converts the single-ended digital transmit (TXD) and receive (RXD) signals from a CAN protocol controller into the differential dominant/recessive signaling required by the CAN bus. It sits between the protocol controller (an MCU with a CAN module) and the twisted-pair bus, providing the drive strength, common-mode rejection, and bus-fault protection needed for robust communication. The PCA82C251 belongs to the broader family of CAN transceivers and is part of the NXP (formerly Philips Semiconductors) automotive connectivity portfolio. Key features of the PCA82C251T include a maximum data rate of 1 MBd, wide supply voltage range of 4.5V to 5.5V (typical 5V), bus terminals tolerant to -27V to +40V transients, low current consumption in standby and recessive states, thermal shutdown protection, and current limiting on the bus outputs. The device operates over the -40C to +125C automotive temperature range, making it suitable for under-hood applications and other harsh industrial environments. It is supplied in the industry-standard 8-pin SOIC (SO-8) package for reflow-soldered surface-mount assembly. The PCA82C251T uses a bipolar CMOS process with on-chip bus-driver protection and slope-control circuitry to limit RFI emissions. Its high-impedance bus input during supply loss prevents the device from loading the bus when unpowered, supporting multi-node hot-swap scenarios. Compared to lower-voltage CAN transceivers, the 24V-tolerant bus pins make this part specifically suited for trucks, buses, agricultural machinery, and industrial CAN networks powered from 24V rails where common-mode transients exceed the range of 12V-only parts. Typical applications include 24V truck and bus CAN networks, agricultural and construction equipment CAN buses, industrial automation CANopen networks, forklift and material-handling vehicle communication, and CAN-based battery management in 24V lead-acid battery stacks. The ISO 11898-24V conformance also makes it a candidate for heavy-duty on-road and off-road vehicle communication backbones. When designing with the PCA82C251T, note that it is a legacy part and the modern TJA1051T, TJA1042T, or TJA1057T from NXP offer lower quiescent current, faster loop times, and improved EMC behavior for new designs. Engineers should select a 24V-rated replacement only when pin-compatibility or bus-fault tolerance is critical; the standard 12V TJA1050T is NOT a drop-in because its bus common-mode range is narrower and will not survive 24V-system transients. This page synthesizes distributor pricing, verified drop-in alternatives (same-brand and cross-brand in SOIC-8), practical design notes, and a parameter comparison table not bundled together on the manufacturer's product page.

RFQ Contact
PCA82C251T-YM118 - 24V CAN Transceiver, 1Mbps, SOIC-8 | NXP
PCA82C251T-YM118

PCA82C251T-YM118 - 24V CAN Transceiver, 1Mbps, SOIC-8 | NXP

The NXP PCA82C251T-YM118 is a legacy CAN bus transceiver for 24 V systems, providing the physical interface between a CAN protocol controller and the differential CAN bus. Housed in an 8-pin SO (SOIC-8) surface-mount package, it supports data rates up to 1 Mbps and operates from a single 5 V supply (4.5 V to 5.5 V), with bus pins tolerant to ±27 V of common-mode voltage for harsh 24 V automotive and industrial environments. A CAN transceiver (Controller Area Network transceiver) is a physical-layer device that converts the digital transmit/receive logic of a CAN protocol controller into the differential voltage signaling required by the CAN bus standard (ISO 11898). Within the broader system hierarchy, a CAN transceiver sits between the protocol controller (MCU) and the physical wiring harness, and belongs to the family of differential line drivers / interface ICs / wired-connectivity semiconductors. The 82C251 is the third-generation "PCA82C251" device, designed for 24 V truck and bus applications and predates the modern TJA1050 / TJA1042 / TJA1051 family. Key features include ±27 V bus fault protection on CANH and CANL, thermal shutdown with automatic recovery, a current-limited transmitter for short-circuit protection on the bus, and a low-current standby mode (typ. 275 µA supply current per Mouser listing). The differential receiver provides high common-mode rejection, and the driver stage supports slew-rate-limited transmission at speeds up to 1 Mbaud. The device exposes TxD, RxD, VCC, GND, CANH, CANL, Vref, and Rs pins on the SO-8 footprint. The architecture uses a bipolar process optimized for high bus voltage tolerance, with on-chip protection diodes clamping transient voltages beyond the supply rails. The Rs pin selects between high-speed, slope-control, and standby modes, providing a software/hardware mechanism for EMC tuning or low-power operation when the bus is idle. Typical applications include 24 V truck and bus CAN nodes, industrial CANopen networks, automotive body and chassis ECUs, agricultural machinery telemetry, and marine electronics. It is a pin-compatible second-source for the legacy PCA82C251 footprint, useful when modern 12 V TJA parts are not suitable. When designing with this part, place a 100 nF decoupling capacitor close to the VCC pin and use a split termination (60 Ω + 60 Ω + 100 nF to ground) at each end of the CAN bus for proper 24 V signal integrity. The Rs pin mode selection must be configured via a resistor to ground or to VCC; leaving it floating is not recommended. The PCA82C251T is marked NRND by NXP - prefer the TJA1051T or TJA1057T for new designs, but this part remains in production for legacy 24 V applications. This page synthesizes distributor stock, parametric data, drop-in second sources, and application guidance drawn from NXP's PCA82C251 datasheet plus current distributor inventory, not all of which appears in a single manufacturer PDF.

RFQ Contact
PCA82C251T/N3,118 - 24V CAN Transceiver SOIC-8 | NXP
PCA82C251T-N3118

PCA82C251T/N3,118 - 24V CAN Transceiver SOIC-8 | NXP

The NXP PCA82C251T/N3,118 is the interface between a CAN protocol controller and the physical bus, primarily intended for applications up to 1 MBaud in 24 V truck and bus systems. It provides differential transmit capability to the bus and differential receive capability to the CAN controller and is fully compatible with the ISO 11898-24 V standard. The /N3,118 suffix denotes the SOIC-8 (D-package) tape-and-reel delivery option used for high-volume automated assembly. A CAN transceiver (Controller Area Network transceiver) is a physical-layer IC that converts the digital transmit (TXD) and receive (RXD) signals of a CAN protocol controller into the differential CANH and CANL bus signals, and vice versa. Within the broader hierarchy, a CAN transceiver is a type of bus transceiver, which is a type of interface IC, which sits inside the Interface ICs category of integrated circuits. The PCA82C251 family targets 24 V automotive and industrial systems where high bus robustness and good electromagnetic compatibility are required. Key features include a -27 V to +40 V bus fault tolerance on CANH/CANL, thermal shutdown protection, current limiting on the transmitter outputs, and a slope-control pin that lets the user programme the bus rise/fall time. The IC operates from a single 4.5 V to 5.5 V supply, draws a typical quiescent current of 16 mA in recessive mode, and survives automotive transients on the bus lines. The SOIC-8 plastic package offers a small PCB footprint with a standard 1.27 mm pin pitch. Typical applications include 24 V truck and bus CAN nodes, industrial CANopen networks, agricultural and construction machinery, and any 12 V or 24 V CAN bus node requiring the classic PCA82C251 silicon. The PCA82C251 is the second-generation PCA82C250 follow-on and is widely second-sourced across the industry. Note that NXP has moved this part to NRND (Not Recommended for New Designs) - new designs should evaluate TJA1043, TJA1051, or TJA1042 for similar 24 V capability. When designing with this part, place a 100 nF decoupling capacitor as close as possible to pin 8 (VCC) and follow the ISO 11898 bus termination of 120 Ω at each end of the bus. The slope-control resistor on pin 8 (Rs) must be chosen against the desired bit rate; for 1 MBaud operation NXP recommends tying Rs to ground, while for lower bit rates a larger resistor reduces EMI. This page synthesises distributor stock, drop-in equivalents, and design guidance not found in the standalone datasheet PDF.

RFQ Contact
PCA82C251T/YM,112 - CAN Transceiver for 24V Systems | NXP
PCA82C251T-YM112

PCA82C251T/YM,112 - CAN Transceiver for 24V Systems | NXP

The NXP Semiconductors PCA82C251T/YM,112 is a legacy Controller Area Network (CAN) transceiver for 24 V systems, supplied in an 8-pin SOIC package (SOT96-1 / SO-8). The device provides a single differential transmit driver and a single differential receiver, providing the physical interface between a CAN protocol controller and the differential CAN bus. It operates from a single 4.5 V to 5.5 V supply, supports data rates up to 1 Mbaud, and is fully compatible with the ISO 11898-24 V standard. What is a CAN transceiver? A CAN transceiver (Controller Area Network transceiver) is a physical-layer interface IC that bridges a digital CAN protocol controller — typically a microcontroller with a built-in CAN module — and the differential CAN bus wiring found in vehicles, industrial equipment, and factory automation systems. Within the broader semiconductor hierarchy, a CAN transceiver belongs to the Interface ICs family, which sits inside the Integrated Circuits product tree. It is the companion IC to a CAN controller, the safety/transceiver side of an automotive/industrial bus, providing the differential drive strength, common-mode tolerance, and bus-fault robustness that digital logic alone cannot deliver. Key features of the PCA82C251T/YM,112 include slope-control to reduce Radio Frequency Interference (RFI), thermal shutdown protection, short-circuit protection on the bus pins, and an exposed thermal pad-friendly SO-8 footprint. The transceiver provides recessive and dominant bus states compliant with ISO 11898-24 V, can detect a permanent dominant condition on the bus, and includes a low-current standby mode controlled via the Rs (slope / standby) pin. The bus pins (CANH, CANL) survive load-dump transients encountered in 12 V and 24 V automotive/industrial environments, making the part the workhorse interface for truck, bus, agricultural, and off-road vehicle networks. Internally, the PCA82C251T/YM,112 uses a bipolar transmitter architecture with a precision differential output stage. The slope-control pin (pin 8) lets the designer trade edge rate against RFI; slower edges reduce emissions on unshielded bus cabling at the cost of maximum achievable bit rate. The receiver compares the bus differential voltage against an internal reference with sufficient hysteresis to reject common-mode noise, and the TXD input feeds a dominant/recessive driver that pulls the bus to the ISO 11898-24 V defined levels. A thermal shutdown block protects the output stage against continuous short circuits on CANH or CANL. Typical applications include in-vehicle CAN networks for trucks, buses and agricultural machinery, industrial automation CAN nodes, building automation (HVAC, lifts), and any 24 V battery-powered CAN segment requiring compliance with ISO 11898-24 V. Designers pair the PCA82C251T/YM,112 with microcontrollers that include a CAN controller (such as NXP LPC, S32K, or Kinetis families) and external protection components (TVS diodes, common-mode chokes) on the bus side. When designing with this transceiver, fit a split-termination network (typically 60 Ω total with a 10 nF to 100 nF capacitor to ground) close to the bus pins to match the cable impedance and improve EMC. Slope-control resistance should be chosen to keep edge times short enough for the target baud rate while still meeting automotive EMC limits. Ensure the supply is decoupled with a 100 nF ceramic capacitor placed within a few millimeters of the VCC pin. This page synthesizes NXP datasheet specifications, distributor pricing as of 2026-10-13, drop-in alternatives (same-brand first, then cross-brand), and practical design notes not found in the standalone datasheet to give engineers an actionable component reference.

RFQ Contact
PCA8525TKX - Nano-Power Automotive RTC IC, I2C | NXP
PCA8525TKX

PCA8525TKX - Nano-Power Automotive RTC IC, I2C | NXP

The NXP Semiconductors PCA8525TKX is a high-accuracy, nano-powered Real Time Clock (RTC) and calendar IC with integrated temperature compensation, an I2C-bus interface, and a temperature rating up to 125 C in a 10-lead HVSON package. It is the first RTC IC with an external crystal to feature a default temperature compensation engine, selectable between crystal curvature coefficients of -0.035 ppm/degC2 or -0.04 ppm/degC2. An RTC (real-time clock) IC is a timekeeping device that maintains seconds, minutes, hours, day, weekday, month, and year information with a 32.768 kHz watch crystal. Within the power-management and timing semiconductor hierarchy, RTC ICs form a specialized subset of clock and timing ICs optimized for ultra-low standby current rather than frequency output. RTCs run continuously even when the main processor is off, so battery-backed timekeeping accuracy and supply current are their defining metrics. Key features of the PCA8525 include nano-power supply current for extended battery life, an integrated digital temperature compensation engine that can deliver up to 5x better timekeeping accuracy than a standard uncompensated RTC, and a selectable crystal temperature model. An aging offset register further corrects long-term crystal drift, keeping timekeeping error within minutes per year rather than tens of minutes. The compensation engine periodically measures the die temperature and digitally adjusts the clock, compensating the parabolic frequency-versus-temperature characteristic of tuning-fork crystals. Because compensation is performed on-chip, no external thermistor, lookup table, or MCU overhead is needed. The I2C interface transfers all addresses and data serially, simplifying integration with any host microcontroller. Typical applications include automotive body control modules and gateway ECUs rated to 125 C ambient, smart meters, industrial dataloggers, and battery-powered IoT endpoints where both accuracy and nano-amp timekeeping current are critical. The automotive qualification makes it especially suitable for under-hood-adjacent modules requiring AEC-grade reliability. Design consideration: crystal selection matters. The compensation engine assumes a typical tuning-fork crystal model; verify that the chosen crystal's curvature coefficient matches the selectable -0.035 or -0.04 ppm/degC2 setting for guaranteed accuracy. This page synthesizes distributor sourcing data, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PCA8543AHL - 4x60 Automotive LCD Segment Driver | NXP
PCA8543AHL

PCA8543AHL - 4x60 Automotive LCD Segment Driver | NXP

The NXP Semiconductors PCA8543AHL is an automotive-grade 4 x 60 LCD segment driver with an integrated charge pump, housed in an 80-pin LQFP package (12x12 mm). It drives any static or multiplexed LCD containing up to four backplanes, 60 segments, and 240 elements, communicating with a host MCU through a two-line bidirectional I2C-bus interface. The internal charge pump, built with on-chip capacitors, generates the LCD drive voltages without external pump components. An LCD segment driver is a peripheral IC that generates the timed multi-level waveforms required to drive liquid-crystal displays. The PCA8543 family sits at the intersection of display drivers and automotive-grade power management, bridging a host microcontroller to a character or segment LCD through standardized I2C commands. Its position in the broader hierarchy is segment driver -> display driver -> power management/interface IC -> automotive semiconductor. Key features include 4 backplanes and 60 segment outputs (240 elements total), I2C-bus control with display RAM auto-incremented addressing, an integrated charge pump for VLCD generation, and automotive temperature-grade qualification. The device is designed for low multiplex rates and supports display memory switching to minimize communication overhead. The PCA8543 is compatible with most microcontrollers. The on-chip charge pump removes the need for external high-voltage capacitors or a separate boost converter, simplifying BOM and PCB layout. Combined with low-multiplex-rate operation, this makes the device suitable for instrument-cluster, climate-control, and white-good displays that require reliable contrast over automotive temperature ranges. Typical applications include automotive instrument clusters, climate-control head units, audio head-unit displays, and industrial/HMI segment LCDs. Automotive AEC-Q100-style qualification (typical for this family) supports deployment in cabin electronics where the LCD must remain readable across cold-start and high-ambient scenarios. When designing with the PCA8543AHL, observe I2C-bus address constraints and ensure adequate decoupling near VDD and VLCD pins. Verify pinout against the 80-pin LQFP package drawing before layout to avoid reversed-orientation errors. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate this LCD driver against cross-brand equivalents.

RFQ Contact
PCA8565TS/1,118 - Automotive RTC, 400kHz I2C, TSSOP-8 | NXP
PCA8565TS/1,118

PCA8565TS/1,118 - Automotive RTC, 400kHz I2C, TSSOP-8 | NXP

The NXP PCA8565TS/1,118 is a CMOS Real-Time Clock (RTC) and calendar optimized for low power consumption, providing year, month, day, weekday, hours, minutes and seconds based on an external 32.768 kHz quartz crystal. It features an automotive-grade operating temperature range of -40C to +125C, supply voltage of 1.8 V to 5.5 V, and 400 kHz I2C-bus interface in an 8-pin TSSOP (8-MSOP, 3.00 mm width) package. A Real-Time Clock (RTC) is a dedicated integrated circuit that keeps track of current time and date independently of the main processor, typically using an external 32.768 kHz quartz crystal as the time base. RTCs sit in the broader hierarchy of: RTC -> clock/calendar IC -> timing component -> mixed-signal IC -> semiconductor. They are essential in any embedded system that must maintain accurate wall-clock time across power cycles, including battery-backed designs where the RTC continues counting during main supply loss. Key features of the PCA8565TS include a programmable clock output, interrupt output, integrated voltage-low detector, automatic word-address increment after each read/write, and AEC-Q100 automotive qualification per the NXP product page. The CMOS process and ultra-low standby current make it suitable for always-on systems drawing microamps in backup mode. Technically, the PCA8565TS uses an I2C slave interface with hardware-fixed slave address, communicates at up to 400 kbit/s (Fast-mode), and integrates a power-on reset, oscillator stop flag, and a trickle-charge disable bit. The BCD-coded time/date registers eliminate software-side binary-decimal conversion overhead on small MCUs. Typical applications include automotive instrument clusters, body and chassis ECUs, HVAC controllers, smart meters, industrial data loggers, and IoT edge nodes requiring a long-life backup time source. The wide 1.8 V to 5.5 V supply range allows direct connection to single-cell Li-ion, 3.3 V system rails, or 5 V legacy buses without level shifting. When designing with the PCA8565TS, ensure the 32.768 kHz crystal load capacitance matches the recommended 7 pF internal load (or use external capacitors as needed), keep the crystal traces short and guarded by ground, and reserve a backup supercapacitor or coin cell on VDD to maintain timekeeping across main power loss. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with a focus on cross-brand pin-compatible RTC substitutes for automotive and industrial designs.

RFQ Contact
PCA8574D,512 - 8-Bit I2C I/O Expander 400kHz SOIC-16 | NXP
PCA8574D,512

PCA8574D,512 - 8-Bit I2C I/O Expander 400kHz SOIC-16 | NXP

The NXP PCA8574D,512 is a remote 8-bit I/O expander for the I2C-bus with interrupt output, providing eight quasi-bidirectional general-purpose I/O lines in a 16-pin SOIC (SO16) package. It operates from a single 2.3V to 5.5V supply, supports the Fast-mode 400 kHz I2C bus, and offers three hardware address pins (A0, A1, A2) plus an open-drain active-low interrupt output. An I2C I/O expander is a type of interface IC that lets a microcontroller control additional digital inputs and outputs through the two-wire serial bus (SCL and SDA), reducing the number of GPIO pins the MCU itself must provide. Within the interface IC hierarchy, the PCA8574 sits alongside I2C multiplexers, port expanders and level translators, and is a direct successor in function to the industry-standard PCF8574. Key features include eight quasi-bidirectional ports that can be independently assigned as inputs or outputs, a 400 kHz I2C-bus interface, low standby current of approximately 10 uA, an latched outputs architecture with power-on reset, and an open-drain INT output that notifies the host of any input change. The quasi-bidirectional I/O structure allows a pin to be used as input or output without direction-control registers, simplifying firmware. The three hardware address pins allow up to eight PCA8574 devices (or eight PCA8574A devices with the alternate fixed slave address) on one bus, supporting up to 16 expanders and 128 I/Os, for example 128 LEDs, from a single two-wire bus. Latched outputs directly drive LEDs with high current sink capability. Typical applications include keypads and switch matrices, LED and indicator driving in white goods and industrial control panels, SPDT relay expansion, sensor monitoring in battery-powered products, and remote I/O expansion in automotive body electronics. For design, remember the quasi-bidirectional ports sink strongly but source only weakly (approximately 100 uA at VDD = 5V), so use external pull-ups on input lines and drive LEDs in sink mode. This page synthesizes distributor pricing, verified drop-in alternatives, practical design notes, and EOL lifecycle guidance not found in the manufacturer datasheet alone.

RFQ Contact
PCA8574D-T - 8-Bit I2C I/O Expander 400kHz | NXP
PCA8574D-T

PCA8574D-T - 8-Bit I2C I/O Expander 400kHz | NXP

The NXP PCA8574D-T is a remote 8-bit I/O expander for the I2C-bus with interrupt output, housed in a 16-pin SO16 (SOIC) package, operating at up to 400 kHz Fast-mode I2C. It provides general-purpose quasi-bidirectional I/O expansion for most microcontroller families via the two-line bidirectional I2C-bus (serial clock SCL and serial data SDA). An I/O expander is a type of interface IC within the broader hierarchy of interface and connectivity semiconductors. It allows a microcontroller with limited GPIO pins to control additional digital inputs and outputs over just two bus lines, reducing pin count, board space, and wiring complexity. I/O expanders are common companions to MCUs such as those from NXP, STMicroelectronics, and Microchip in embedded systems. Key features of the PCA8574D include an 8-bit quasi-bidirectional port with latched outputs, an open-drain interrupt (INT) output that alerts the host controller to remote input changes, and three hardware address pins (A0, A1, A2) that allow up to eight PCA8574 devices on the same I2C-bus. Combined with the PCA8574A variant (different fixed slave address), up to 16 devices can share one bus, supporting up to 128 I/Os, for example driving 128 LEDs. Architecturally, the device integrates an 8-bit quasi-bidirectional I/O port, an I2C-bus slave interface with Fast-mode 400 kHz support, and power-on reset logic that sets all ports to a defined state at startup. The quasi-bidirectional structure means each pin can serve as input or output without a direction-control register, simplifying firmware. Typical applications include keypad scanning and keyboard interfaces, LED and indicator driving, backplane status monitoring in industrial systems, and general-purpose GPIO expansion in automotive body electronics and consumer appliances. Design consideration: quasi-bidirectional pins source a weak holding current when set high, so external loads must sink current to pull a pin low; check sink capability per the manufacturer datasheet before driving heavier loads. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PCA8575PW,118 - 16-bit I2C I/O Expander TSSOP-24 | NXP
PCA8575PW,118

PCA8575PW,118 - 16-bit I2C I/O Expander TSSOP-24 | NXP

The NXP Semiconductors PCA8575PW,118 is a remote 16-bit I/O expander for the I2C-bus (SCL/SDA), providing a 16-bit quasi-bidirectional parallel port and an interrupt output, housed in a 24-pin TSSOP (4.4 mm body width) surface-mount package and supplied on Digi-Reel. The device supports a supply range of 2.3 V to 5.5 V and operates at an I2C clock frequency up to 400 kHz (Fast-mode), making it drop-in compatible with the wide majority of 3.3 V and 5 V microcontroller I2C peripherals. An I/O expander is a bus-attach peripheral that multiplies a host controller's general-purpose I/O count by adding parallel input/output pins over a serial link. The PCA8575PW,118 belongs to the I2C-bus I/O expander family (I/O expander -> GPIO expander -> parallel I/O port -> interface IC -> integrated circuit). Quasi-bidirectional outputs can be driven low actively by the device or pulled high weakly, which lets a single pin directly sink LED current when configured as an output and still be read as a logic high when the external driver releases the line - useful for keypad scanning and switch-matrix polling. Key features include 16 individually addressable I/O lines, an open-drain interrupt (INT) line that asserts when any input changes state, three hardware address pins (A0/A1/A2) allowing up to eight devices on one bus (128 I/O total), latched outputs with high-current drive capability suitable for direct LED driving, and a low standby current that suits battery-powered designs. The integrated address decoder, input filter, and edge-triggered interrupt block reduce host firmware overhead because the MCU only services the PCA8575PW,118 when an actual port event occurs. Typical applications include adding pushbuttons, keypads, LED indicators, relay drivers, and sensor multiplexing to 8-pin microcontrollers, white-goods and appliance front panels, industrial PLC I/O modules, and PC accessory sideband ports. The 400 kHz Fast-mode I2C clock and 2.3 V to 5.5 V supply let it interface directly with 3.3 V ARM Cortex-M parts and 5 V legacy MCUs without level translation. When designing with this device, place the standard 100 nF VCC bypass within 5 mm of the supply pin and add 10 kohm pull-ups on SDA and SCL - quasi-bidirectional outputs still require external pull-ups to drive logic high reliably. Reserve the INT pin for an MCU edge-triggered input and avoid tying it permanently high; the address pins A0-A2 must be tied to a fixed logic level and not left floating at power-up. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the NXP datasheet alone, including the comparison and pinout data that engineering teams need to qualify a second source.

RFQ Contact
PCA9306H - Dual I2C/SMBus Voltage-Level Translator | TI
PCA9306H

PCA9306H - Dual I2C/SMBus Voltage-Level Translator | TI

The Texas Instruments PCA9306H is a dual bidirectional I2C-bus and SMBus voltage-level translator with an enable (EN) input, operating from 1.2 V to 3.3 V on VREF1 and 1.8 V to 5.5 V on VREF2, housed in an 8-pin VSSOP (DCT) package. It translates between two voltage domains without a direction pin, making it a compact solution for mixed-voltage I2C and SMBus networks. A voltage-level translator is an interface IC that safely connects digital signals operating at different supply voltages, for example a 1.8 V microcontroller I2C peripheral talking to a 3.3 V or 5 V sensor. Within the signal-chain hierarchy, the PCA9306H belongs to the level-translator family of interface ICs, positioned alongside I2C buffers, repeaters, and multiplexers. Because I2C is an open-drain bus, translation requires a bidirectional pass element rather than a directional buffer - exactly the architecture this device implements. Key features include directionless bidirectional translation, an enable pin that puts both switch channels into a high-impedance state when LOW, and low ON-state resistance of the pass FET, which keeps propagation delay minimal. The wider VREF1 range of the PCA9306H (1.2 V to 3.3 V, versus 1.0 V to 3.6 V or lower-floor variants in the family) makes it suitable for modern low-voltage processors. It supports standard-mode (100 kHz), fast-mode (400 kHz), and fast-mode plus (1 MHz) I2C devices as well as SMBus systems. Architecturally, the device is a pair of N-channel pass transistors with gate drive referenced to EN and the reference supplies. When EN is HIGH, SDA1/SCL1 connect to SDA2/SCL2; pulling either side low through its open-drain pull-up propagates the low to the other side, achieving the gate-threshold offset that produces the voltage shift. Because there is no active buffering, signal integrity is essentially transparent, with propagation delay dominated only by the switch Ron and external pull-up resistors. Typical applications include connecting 1.8 V MCUs to 3.3 V or 5 V sensors and EEPROMs, translating between 3.3 V SMBus hosts and lower-voltage peripherals in servers and networking cards, and interfacing low-voltage FPGA or SoC I2C banks to 5 V legacy buses in industrial control systems. For reliable operation, size the pull-up resistors on both sides of the translator according to the bus speed and bus capacitance; each side must have its own pull-up. Also note the 200 kOhm internal pass-gate resistance behavior at low VREF2 voltages when calculating rise times. This page synthesizes distributor data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PCA9306USG - Dual I2C/SMBus Voltage-Level Translator | onsemi
PCA9306USG

PCA9306USG - Dual I2C/SMBus Voltage-Level Translator | onsemi

The onsemi PCA9306USG is a dual bidirectional I2C-bus and SMBus voltage-level translator with an enable (EN) input, operating from 1.2 V to 3.3 V VREF1 and 1.8 V to 5.5 V VREF2, delivering 1.5 ns typical propagation delay and 3.5 ohm ON-state resistance in an 8-pin VSSOP (US8) package. A voltage-level translator is an interface IC that allows devices operating at different supply voltages - for example a 1.8 V microcontroller and a 5 V sensor - to share the same two-wire bus safely. Within the signal-chain hierarchy, level translators sit in the interface IC family alongside I2C multiplexers, buffers, and repeaters. The PCA9306 belongs to the switch-based (passive) translator class: it uses two N-channel pass transistors per channel rather than active output stages, so the bus is pulled up naturally by the resistors on each rail. Key features include bidirectional voltage translation between 1.2 V and 5 V with no direction pin, support for Standard-mode (100 kbps), Fast-mode (400 kbps), and Fast-mode Plus (1 Mbps) I2C-bus plus SMBus operation, a very low 3.5 ohm ON-state connection that minimizes signal distortion, and an active-high EN input that isolates both buses when the translator is not needed. The 1.5 ns rise/fall propagation characteristic keeps bus timing margin intact even at Fast-mode Plus speeds. The switch architecture means the PCA9306 introduces virtually no drive strength of its own - the 64 mA figure refers to the pass-transistor current handling capability. Because it is a passive switch, lock-up free operation is guaranteed even during bus contention or partial power-down, a known failure mode of active level-shifter designs. Both SDA and SCL channels are identical, so the device handles the full 2-bit I2C bus in a single package. Typical applications include connecting 1.8 V to 3.3 V microcontrollers to 5 V I2C sensors and EEPROMs, level-shifting SMBus rails in server power supplies, battery-powered portable systems where two rail domains must communicate, and mixed-voltage industrial control modules. Design consideration: the EN pin must be driven above the higher VREF2 rail to guarantee the pass gates turn fully on; always provide pull-up resistors on both sides of each channel sized for the respective rail. This page synthesizes distributor cross-reference data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing as of 2026-10-19.

RFQ Contact
PCA9500D - 8-Bit I/O Expander with EEPROM | NXP
PCA9500D

PCA9500D - 8-Bit I/O Expander with EEPROM | NXP

NXP Semiconductors PCA9500D is an 8-bit I2C and SMBus I/O port expander with an onboard 2-kbit EEPROM, eight quasi-bidirectional GPIO pins, and operation up to 400 kHz in a 16-pin SOIC package. The expander adds remote status inputs and indicator or control outputs to a host microcontroller while preserving the familiar I2C two-wire interface. An I2C I/O expander is a bus-interface peripheral that converts serial commands from a controller into parallel digital states. In the broader hierarchy, it belongs to interface ICs, digital I/O control, and general-purpose bus peripherals. The PCA9500D combines an 8-bit quasi-bidirectional port with nonvolatile storage, allowing configuration or board-identification data to be retained between power cycles. The three address pins use internal pull-up resistors, allowing up to eight devices to share the common I2C bus. The GPIO address matches the PCF8574, while the EEPROM address matches the PCF8582C-2; consequently, one device appears as two separately addressed functions to the bus master. Its 400 kHz bus rating supports faster communication than the common 100 kHz I2C operating mode. Because each port pin can be assigned independently as an input or output, the device can monitor board-level status and activate indicators such as LEDs. The quasi-bidirectional structure is useful for straightforward bus interfacing, although external pull-ups, electrical-level compatibility, and the intended input or output state must be considered in each design. Typical uses include industrial control boards, removable or backplane cards, LED and switch interfaces, configuration storage, and small embedded systems where GPIO conservation is valuable. The NXP product information specifically identifies hot-insertion support as useful in removable-card and backplane systems. A correct implementation should verify the actual device address, EEPROM map, logic thresholds, pull-up values, and pin functions against the manufacturer datasheet. Do not infer unavailable timing, voltage, temperature, or package dimensions from distributor summaries. For exact design values, consult the linked NXP documentation and validate firmware behavior across power-up, reset, bus faults, and hot-plug conditions.

RFQ Contact
PCA9500PW - 8-Bit I/O Expander with 2-kbit EEPROM | NXP
PCA9500PW

PCA9500PW - 8-Bit I/O Expander with 2-kbit EEPROM | NXP

The NXP Semiconductors PCA9500PW is an 8-bit I2C-bus and SMBus I/O port expander with an integrated 2-kbit EEPROM in a 16-pin TSSOP package. It operates from 2.5 V to 3.6 V, supports I2C/SMBus communication up to 400 kHz, and provides eight quasi-bidirectional data pins that can be configured independently as inputs or outputs. Three hardware address pins allow as many as eight PCA9500 devices to share one bus. According to the NXP datasheet, the bus master sees the GPIO controller and EEPROM as two separate devices, while the GPIO configuration register is accessed in a manner similar to the PCF8574. An I/O expander is a general-purpose interface IC that increases the number of digital input and output lines available to a host microcontroller without requiring a large parallel GPIO package. In the product hierarchy, the PCA9500 is an I/O expander within the broader category of interface ICs and bus-interface semiconductors. Its quasi-bidirectional ports can read external logic states or drive indicators and other digital loads, making it useful when the main processor has too few general-purpose pins for switches, sensors, LEDs, or control signals. The principal feature is the integrated 2-kbit EEPROM, which adds a small amount of nonvolatile storage for configuration or identification data. The eight GPIO pins support mixed input/output operation, and the three address inputs expand the device count available on a shared I2C or SMBus system. A maximum bus rate of 400 kHz is suitable for standard embedded control buses, while the 2.5 V to 3.6 V supply range targets conventional low-voltage digital systems. The NXP datasheet identifies the PCA9500 as a drop-in replacement for the PCF8574, adding EEPROM functionality to a familiar interface arrangement. The PCA9500 uses the same basic I2C write/read model commonly associated with PCF8574-style devices. Separate device addresses allow the GPIO function and the EEPROM to be accessed independently by the bus master. This separation is useful when the host must read or update stored data without changing live output states. Quasi-bidirectional inputs include an internal pull-up arrangement, making the device convenient for open-drain-style bus signaling and for reading switches or logic states, although external pull-up and drive-strength checks remain important in the final circuit. Typical applications include consolidating LED indicators, reading banks of switches or interlocks, adding configurable control outputs to a microcontroller module, and storing board configuration or asset information in the EEPROM. It can also reduce controller pin count in compact embedded systems while preserving a standard I2C/SMBus connection. Eight address-selectable devices provide substantial expansion without requiring additional host pins. The primary design consideration is to treat the quasi-bidirectional pins as a bidirectional interface rather than as unrestricted push-pull outputs. Check pull-up strength, voltage levels, bus capacitance, and the timing requirements of every connected peripheral. Confirm the PCB land pattern and pin numbering against the manufacturer datasheet before production because the verified product information does not provide a complete public pin table in the supplied material. This page consolidates the verified NXP product information, distributor identification, lifecycle status, bus characteristics, and manufacturer-backed drop-in relationships into an engineering-focused resource. It also distinguishes verified capabilities from parameters that still require confirmation from the full manufacturer datasheet.

RFQ Contact
PCA9501PW - 8-Bit I/O Expander with 2-kbit EEPROM | NXP
PCA9501PW

PCA9501PW - 8-Bit I/O Expander with 2-kbit EEPROM | NXP

NXP Semiconductors PCA9501PW is an 8-bit I2C and SMBus I/O expander with an integrated 2-kbit EEPROM, eight independently configurable quasi-bidirectional GPIO pins, and support for bus operation up to 400 kHz. The device is supplied in a 20-pin TSSOP package and is designed for 2.5 V to 3.6 V operation. An I/O expander is an interface IC that increases the number of digital input and output pins available to a host microcontroller or embedded processor. The PCA9501 sits within the interface IC hierarchy, where it connects a serial I2C or SMBus controller to LEDs, switches, sensors, and other board-level logic. Its quasi-bidirectional outputs can read external logic states while also driving indicator and control devices. The PCA9501 provides eight GPIO ports, a 2-kbit on-board EEPROM, an interrupt output, and six hardware address inputs. The EEPROM provides nonvolatile storage alongside the GPIO function, allowing the bus master to retain configuration or identification data. Hardware address pins allow up to 64 PCA9501 devices to coexist on one bus when address assignments and bus loading permit. The I2C and SMBus interfaces support operation at frequencies up to 400 kHz. Each GPIO may be configured independently as an input or output, and the input data and output configuration registers follow the familiar programming model of the PCF8574 family. The interrupt pin provides a hardware indication that one or more inputs have changed, reducing the need for continuous polling. Typical uses include LED and relay-control interfaces, configuration and status I/O, telecommunications equipment, networking hardware, base-station systems, and general-purpose expansion for installed boards. The integrated EEPROM also makes the device useful where a small amount of nonvolatile board data must accompany the I/O functions. Designers should account for the electrical behavior of quasi-bidirectional ports, pull up I2C and open-drain interrupt lines as required, and verify logic thresholds before driving external loads. PCB layouts should route the bus cleanly, provide stable bypass capacitance near the supply pins, and maintain adequate spacing between the TSSOP body and adjacent copper features. This page combines the verified NXP product information, manufacturer datasheet, distributor listing, and cross-reference results with practical guidance on pin behavior, bus addressing, interrupt handling, EEPROM use, PCB layout, and drop-in replacement assessment.

RFQ Contact
PCA9507DP,118 - 2-Wire Bus Extender, 5V, 8-TSSOP | NXP
PCA9507DP,118

PCA9507DP,118 - 2-Wire Bus Extender, 5V, 8-TSSOP | NXP

The NXP PCA9507DP,118 is a 2-wire serial bus extender with integrated 3.3 V to 5 V level shifting, one bidirectional I²C/SMBus channel, and a 400 kHz maximum clock rate, packaged in an 8-pin TSSOP (SOT505-1, DP suffix). It provides bidirectional buffering of SDA and SCL lines while preserving all I²C operating modes (master/slave, multi-master, arbitration) across the level-shift boundary, and it extends the usable bus length up to 18 meters for HDMI DDC, I²C-bus, and SMBus links. The device operates from a 2.7 V to 5.5 V supply and is specified across the -40 °C to +85 °C industrial temperature range. What is an I²C bus extender? An I²C bus extender (also called a bus repeater or accelerator) is a type of interface IC that sits between two segments of a 2-wire serial bus and buffers both SCL (clock) and SDA (data) lines. Its purpose is twofold: to overcome capacitive loading limits that cap I²C bus length, and to translate voltage levels between dissimilar supply domains. The PCA9507 sits in the broader hierarchy of bus interface ICs (interface IC > bus extender > signal buffer/repeater), and is a specialized sibling of the I²C hub/switch family such as the PCA9543A. Key features of the PCA9507DP,118 include: 1 channel of buffered SDA + SCL; support for Standard-mode (100 kHz), Fast-mode (400 kHz), and 3.4 MHz Fast-mode Plus overshoot tolerant operation on the upstream port; 2.7 V to 5.5 V supply range; 218 ns typical propagation delay; and integrated rise-time accelerators that allow designers to drop the bus pull-up resistors while still meeting rise-time budgets on long cables. It also provides hot-swap insertion tolerance so that cards can be plugged into a live backplane without corrupting the bus. The internal architecture uses two N-channel MOSFET pass gates with charge-pump enhancement, plus direction-sensing comparators that automatically configure the channel as upstream or downstream. The upstream (master-side) port tolerates 3.3 V to 5 V, while the downstream port can operate down to 2.7 V, enabling typical 3.3 V-to-5 V HDMI DDC level shifting. The TSSOP-8 footprint makes the part suitable for compact HDMI connector breakouts, display modules, and embedded backplanes. Typical applications include HDMI/DVI Display Data Channel (DDC) level shifters, I²C-bus extension over long cables (up to 18 m) in industrial control panels, SMBus fan and chassis management links, and any board-to-board 2-wire link that must bridge a voltage-level or capacitive-load gap. Because the device preserves arbitration and clock-stretching behavior, it is safe to insert in the middle of an existing multi-master bus. When designing with the PCA9507, remember that the part is a pure bus extender with no pull-ups on either side. Both upstream and downstream segments still require external pull-up resistors sized to the segment capacitance, and the device's quiescent current (typically a few hundred microamps) must be included in the system power budget. For long cables, place the PCA9507 near the connector to keep the high-impedance stub short. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes for HDMI DDC and long-cable I²C applications - context not collected in the manufacturer datasheet alone.

RFQ Contact