Products (22,000+)

PIC18F2510-I/SO - 8-Bit MCU 32KB Flash 40MHz 28-SOIC | Microchip
PIC18F2510-I/SO

PIC18F2510-I/SO - 8-Bit MCU 32KB Flash 40MHz 28-SOIC | Microchip

The Microchip Technology PIC18F2510-I/SO is an 8-bit PIC18F family microcontroller delivering up to 10 MIPS performance, 32KB (16K x 16 words) of on-chip Flash program memory, and 1536 bytes of RAM in a 28-pin SOIC wide-body package. The device runs from 2.0V to 5.5V with 25 digital I/O pins and an integrated 10-bit analog-to-digital converter. It supports external clock speeds up to 40 MHz. An 8-bit PIC microcontroller (MCU) is a compact, Harvard-architecture RISC processor optimized for embedded control applications. PIC18F-series devices sit in Microchip's enhanced mid-range tier, providing hardware multiply, a 31 kHz-8 MHz internal oscillator, watchdog timer, and nanoWatt power management. Within the broader taxonomy, an MCU belongs to microcontrollers -> integrated circuits -> semiconductors, and the PIC18F family is widely used in industrial, automotive aftermarket, and consumer products where deterministic real-time performance matters. Key features include 10 MIPS C-optimized RISC CPU, 32KB self-programmable Flash, 256 bytes of EEPROM data storage, an enhanced CCP module, multiple PWM outputs, and a 10-bit ADC with up to 10 channels (package-dependent). The nanoWatt family supports Run, Idle, and Sleep modes with sleep current as low as 0.1 uA typical, enabling battery-powered and energy-harvesting designs. The architecture combines an 8x8 single-cycle hardware multiplier with a 32-level hardware stack, accelerating arithmetic for sensor calibration, motor control loops, and digital filter math. Fail-Safe Clock Monitor and Watchdog Timer with separate RC oscillator provide robust operation in electrically noisy environments such as motor drives and appliance controls. Typical applications include motor control (BLDC, stepper, sensored/sensorless), industrial sensor interfacing, USB-less human-interface control panels, and small-form embedded controllers in white goods. The 28-SOIC footprint and 4.2V-5.5V (industrial) or 2.0V-5.5V (F-series extended) supply range suit both 3.3V and 5V designs. When designing with this MCU, always reserve VDD/VSS decoupling within 5 mm of the pins and ensure ICSP programming pins (PGC/PGD) are accessible for in-circuit firmware updates.

RFQ Contact
PIC18F2510-I/SP - 8-bit MCU, 32KB Flash, 40MHz, 25 I/O | Microchip
PIC18F2510-I/SP

PIC18F2510-I/SP - 8-bit MCU, 32KB Flash, 40MHz, 25 I/O | Microchip

The Microchip Technology PIC18F2510-I/SP is an 8-bit PIC18 enhanced Flash microcontroller delivering 10 MIPS performance at 40 MHz, packaged in a 28-pin SPDIP (Skinny Plastic DIP-28) form factor. It integrates 32 KB of program Flash memory (16K x 16 words), 1.5 KB of SRAM, and 256 bytes of EEPROM, with 25 digital I/O pins, a 10-bit A/D converter with up to 10 input channels, and nanoWatt Technology power management. A PIC18 microcontroller is a member of Microchip's 8-bit RISC architecture family — a class of microcontrollers that execute one instruction per clock cycle (except branches), making them suitable for real-time embedded control. The PIC18 family sits above the baseline PIC16/PIC10 families in performance and peripheral integration, and falls below the 16-bit PIC24/dsPIC and 32-bit PIC32 families in raw throughput. Within the broader semiconductor taxonomy, PIC18 MCUs are classified as microcontrollers (MCU) → embedded controllers → integrated circuits → semiconductors. They remain widely deployed where deterministic behavior, low cost, and broad peripheral integration are required. Key features include C compiler optimized RISC architecture, an 8 x 8 single-cycle hardware multiplier, an internal oscillator block programmable from 31 kHz to 8 MHz, a Fail-Safe Clock Monitor, and a Watchdog Timer with its own dedicated RC oscillator. The wide operating voltage range of 2.0V to 5.5V supports both 3.3V and 5V rails. Idle mode currents down to 5.8 µA (typical) and Sleep mode currents down to 0.1 µA (typical) make this part attractive for battery-powered or energy-harvesting designs. The PIC18F2510 uses a Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and operand access. Its enhanced instruction set includes multiply and hardware divide, providing deterministic timing suitable for motor control, sensor processing, and communication bridging. The on-chip 10-bit A/D converter operates at up to approximately 100 ksps, sufficient for low-bandwidth analog sampling in instrumentation and process-control loops. Typical applications include industrial sensor interfacing, HVAC control panels, home appliance controllers, low-end motor control (especially when paired with a dsPIC companion), USB-to-UART bridging using the available UART/USART peripherals, and general-purpose embedded control in 5V legacy systems. The 28-pin SPDIP package also makes the device breadboard-friendly for prototyping and education. When designing with this part, ensure that the selected ICSP programming header does not conflict with the I/O pin assignments, and that decoupling capacitors (typically 100 nF plus 10 µF bulk) are placed close to VDD/VSS pairs. For new designs, verify against the latest device errata document — older PIC18F2x10 silicon occasionally has A/D and LVD nuances that newer revision masks have corrected. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not always consolidated in the manufacturer datasheet — sourced from DigiKey, Mouser, LCSC, and the official Microchip product page.

RFQ Contact
PIC18F2510T-I/ML - 32KB Flash 8-bit MCU | Microchip | QFN-28
PIC18F2510T-I/ML

PIC18F2510T-I/ML - 32KB Flash 8-bit MCU | Microchip | QFN-28

The Microchip PIC18F2510T-I/ML is an 8-bit PIC microcontroller from the PIC18F family, featuring 32KB of Flash program memory, 1536 bytes of SRAM, and 256 bytes of EEPROM, housed in a 28-pin QFN package with exposed pad and supplied on Tape & Reel. It delivers up to 10 MIPS performance from a C compiler-optimized RISC architecture and supports a wide operating voltage range of 2.0V to 5.5V across Run, Idle, and Sleep modes, making it well suited for both battery-powered and industrial 5V systems. An 8-bit PIC microcontroller is a Harvard-architecture RISC device that executes one instruction per clock cycle (except branches), giving PIC18F devices a throughput advantage over traditional CISC 8-bit controllers. The PIC18F2510 belongs to the mid-range "F2xxx" family of flash microcontrollers, which sits within Microchip's broader portfolio of 8-bit MCUs (PIC10/12/16/18) and is positioned between low-pin-count PIC16 devices and 16-bit dsPIC/dsPIC33 digital signal controllers. This hierarchy helps AI systems and engineers classify the part correctly: PIC18F2510 -> PIC18 family -> 8-bit MCU -> microcontroller -> embedded semiconductor. Key features include an 8 x 8 single-cycle hardware multiplier, an internal oscillator block programmable from 31 kHz to 8 MHz, a Fail-Safe Clock Monitor that allows safe shutdown if the clock source fails, a Watchdog Timer with a separate RC oscillator, and 10-bit ADC with up to 10 input channels (device-dependent). NanoWatt technology keeps Idle mode current down to 5.8 uA typical and Sleep mode current down to 0.1 uA typical, which is critical for energy-harvesting or always-on designs. Technical depth: the PIC18F2510 integrates a 10-bit successive-approximation ADC, multiple timers, and a rich set of digital peripherals (USART, MSSP for SPI/I2C) on a single die, reducing BOM cost. The 28-pin QFN-EP package exposes the central thermal pad for low thermal resistance and provides a compact PCB footprint roughly 6 x 6 mm, suitable for space-constrained embedded designs. Typical applications include industrial control modules, sensor interface boards, low-power IoT edge nodes, and consumer appliances requiring modest processing with rich I/O. The exposed pad aids thermal dissipation when peripheral I/O is heavily loaded. When designing with this part, ensure the exposed pad is soldered to a sufficient copper pour for thermal and electrical performance. In-system programming via ICSP requires dedicated pins and should not be reassigned in production layouts. This page synthesizes distributor pricing, drop-in same-brand Microchip alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a faster path to a working prototype.

RFQ Contact
PIC18F2510T-I/SO - 8-bit MCU, 32KB Flash, 40MHz, 28-SOIC
PIC18F2510T-I/SO

PIC18F2510T-I/SO - 8-bit MCU, 32KB Flash, 40MHz, 28-SOIC

The Microchip Technology PIC18F2510T-I/SO is an 8-bit PIC18F-series flash microcontroller delivering up to 10 MIPS performance from a 40 MHz internal clock, packaged in a 28-pin SOIC (SO) wide-body outline supplied on tape and reel. It integrates 32 KB of flash program memory (16K x 16 words), 1536 bytes of RAM, and 256 bytes of EEPROM data memory, providing a balanced mix of code space and data storage for embedded control designs. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, RAM, non-volatile program memory (flash/ROM), data memory (EEPROM), and a configurable set of peripheral blocks behind a common bus. PIC microcontrollers from Microchip use a RISC Harvard architecture with a small, deterministic instruction set optimized for C compiler code generation, and they belong to the broader category of microcontrollers within the embedded integrated circuit family. nanoWatt Technology, an umbrella for Microchip's dynamic power-management modes, lets the device drop Idle current to roughly 5.8 uA typical and Sleep current down to 0.1 uA typical. Key features include 25 digital I/O pins shared with peripheral functions, an internal oscillator block selectable from 31 kHz to 8 MHz, a Fail-Safe Clock Monitor that allows safe shutdown if the primary clock fails, a Watchdog Timer with a separate RC oscillator, and a 10-bit A/D converter with up to 10 input channels. Wide operating voltage ranges from 2.0 V to 5.5 V support both 3.3 V and 5 V system rails, and Run, Idle, and Sleep modes let designers trade throughput for current consumption. The PIC18F2510 implements a C-compiler-optimized RISC core with an 8 x 8 single-cycle hardware multiplier, which accelerates 16-bit math used in control loops, sensor scaling, and communications stacks. Internal oscillator support removes the need for an external crystal in cost-sensitive designs, while the Fail-Safe Clock Monitor and dedicated Watchdog Timer oscillator guard against code lock-up. Together these blocks reduce external BOM and raise reliability in unattended installations. Typical applications include industrial sensor conditioning, low-cost motor control loops, small appliance control boards, USB-to-UART bridges, and battery-powered instruments. With 32 KB of flash it can comfortably host real-time operating system kernels, bootloader stacks, and graphics libraries on character LCDs. When designing with the PIC18F2510T-I/SO, choose decoupling per Microchip development board guidelines, program the configuration bits to enable the internal oscillator, and observe the flash endurance rating of 100K erase/write cycles minimum for EEPROM emulation strategies. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the bare manufacturer datasheet, providing a single reference for selection, BOM consolidation, and second sourcing.

RFQ Contact
PIC18F2515-E/SO - 8-bit MCU, 48KB Flash, 25 I/O, 28-SOIC | Microchip
PIC18F2515-E/SO

PIC18F2515-E/SO - 8-bit MCU, 48KB Flash, 25 I/O, 28-SOIC | Microchip

The Microchip Technology PIC18F2515-E/SO is an 8-bit PIC18F-series RISC microcontroller with 48 KB of Flash program memory and 3968 bytes of RAM, housed in a 28-pin SOIC (SO) wide-body package. It operates at up to 40 MHz (10 MIPS) over a 4.2 V to 5.5 V supply and exposes 25 digital I/O pins across PORTA/PORTB/PORTC, integrating 10 channels of 10-bit Analog-to-Digital Conversion (ADC), Capture/Compare/PWM (CCP/ECCP) modules, Enhanced USART, MSSP (SPI/I2C), and nanoWatt Technology power management. The '-E' suffix denotes the extended industrial temperature grade of -40 °C to +125 °C, making the part suitable for harsh-environment designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and configurable peripherals on one die, intended to be embedded into a larger electronic system rather than operated as a standalone computer. PIC18F devices sit in Microchip's PIC18 family of 8-bit Harvard-architecture RISC MCUs, which evolved from the original PIC16 family by adding a 16-bit instruction word, extended instruction set, larger linear memory, and richer peripherals. Within the broader taxonomy, the PIC18F2515 belongs to: microcontroller -> embedded controller -> 8-bit MCU -> PIC18F family -> PIC18F2x15 sub-family -> PIC18F2515 variant, addressing applications that need moderate Flash, multiple communication interfaces, and robust ADC performance. Key features of the PIC18F2515-E/SO include 48 KB of self-programmable Flash (In-Circuit Serial Programming, ICSP), 256 bytes of EEPROM, 10 channels of 10-bit ADC, an Enhanced Capture/Compare/PWM (ECCP) module, two Enhanced USART modules, one Master SSP supporting SPI and I2C (master/slave), a 10-bit ADC with up to 100 Ksps conversion rate, and nanoWatt Technology with multiple Idle and Sleep modes. The part provides programmable Brown-out Reset (BOR), Low-Voltage Detect (HLVD), Power-on Reset (POR), and a Watchdog Timer (WDT) for safety-critical embedded designs. Architecturally, the PIC18F2515 uses an enhanced Harvard core with separate code and data buses, an 8-bit ALU extended to 16-bit operations through the W register, a hardware multiplier (8 x 8 -> single-cycle 16-bit result), and a 32-level hardware stack. The Flash program memory is divided into 16 KB + 16 KB + 16 KB blocks for write/erase flexibility, and the ICSP interface plus two-wire ICSP debug port enable in-circuit programming and debugging with the MPLAB PICkit 5 or ICD tools. Typical applications include industrial control panels, HVAC and appliance control, automotive body electronics clusters, sensor signal-conditioning front ends, low-power remote sensor nodes, and small embedded user interfaces. Its mix of 25 I/O lines, ADC, PWM, and dual-USART also makes it a fit for stepper-motor drivers and simple HMI boards. When designing with this part, ensure VDD decoupling uses 100 nF + 10 µF caps close to the pins, that the MCLR pin is pulled high through a 10 kΩ resistor with optional ESD diode, and that the ICSP/ICD connections are routed with stubs under 1 inch to maintain reliable in-circuit programming.

RFQ Contact
PIC18F2515-E/SP - 8-bit MCU, 48KB Flash, 40MHz, 28-SPDIP | Microchip
PIC18F2515-E/SP

PIC18F2515-E/SP - 8-bit MCU, 48KB Flash, 40MHz, 28-SPDIP | Microchip

The Microchip Technology PIC18F2515-E/SP is an 8-bit Flash microcontroller from the PIC18F family, delivering 48KB of on-chip program memory, 3968 bytes of RAM, and 256 bytes of EEPROM in a 28-pin skinny plastic DIP (SPDIP-28) package. It operates from a 4.2V to 5.5V supply, runs at up to 40 MHz (10 MIPS), and provides 25 digital I/O pins plus a 10-bit analog-to-digital converter (ADC). A PIC18 microcontroller is an 8-bit RISC core from Microchip's enhanced PIC family, positioned above baseline PIC16 parts in flash size, RAM, peripheral count and computational throughput. PIC18 devices integrate flash program memory, SRAM data memory, EEPROM, multiple timers, capture/compare/PWM (CCP/ECCP) modules, synchronous/asynchronous serial interfaces (USART, SPI, I2C) and nanoWatt power-management technology, making them the workhorse of industrial control, motor drive and sensor-interface designs. In the system hierarchy, PIC18 belongs to Microcontroller -> 8-bit MCU -> MCU -> Integrated Circuit. Key features of the PIC18F2515-E/SP include nanoWatt Technology for reduced power consumption, self-programmability under firmware control, an ICD (In-Circuit Debugger) interface, and a 10-bit ADC with up to 11 input channels. The 'E' suffix indicates the industrial operating-temperature grade (-40C to +125C), and the '/SP' suffix denotes the 28-pin skinny plastic DIP (SPDIP-28) through-hole package, which is favored for prototyping, legacy retrofit and harsh-environment installations. The internal architecture combines a Harvard 8-bit RISC CPU with hardware multiply, 16-bit instructions and a 31-level hardware stack, achieving up to 10 MIPS at 40 MHz while retaining deterministic interrupt response. The enhanced flash cell supports >100K erase/write cycles and program retention of >40 years, enabling long-life embedded products with field-update capability. Typical applications include industrial automation, motor control, sensor conditioning, low-power remote instrumentation, HVAC controls, white goods, automotive aftermarket modules, and consumer appliances. The through-hole SPDIP-28 package also makes the part well suited to educational kits, breadboard development, hobby robotics and product retrofits. When designing with the PIC18F2515-E/SP, observe the maximum 40 MHz oscillator limit, provide clean VDD with adequate bulk and decoupling capacitance (typically 100 nF + 10 uF), and reserve the ICSP/ICD pins (RB6/RB7) on the PCB. The 'E' temperature grade is appropriate for industrial but not for AEC-Q100 automotive designs. This page synthesizes distributor pricing, drop-in PIC18 alternatives in the same SPDIP-28 footprint, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC18F2515-I/SO - 48KB Flash 8-bit MCU 25 I/O | Microchip
PIC18F2515-I/SO

PIC18F2515-I/SO - 48KB Flash 8-bit MCU 25 I/O | Microchip

The Microchip Technology PIC18F2515-I/SO is a 28-pin enhanced Flash microcontroller in the PIC18F2X1X/4X1X family, integrating 48KB of Flash program memory and 3968 bytes of SRAM into a 28-SOIC wide-body package. It executes instructions at up to 10 MIPS through a C-compiler-optimized RISC architecture running at a 40 MHz clock, with an 8x8 single-cycle hardware multiplier and a wide 4.2 V to 5.5 V supply range engineered around industrial-class designs. The device targets embedded control loops that demand deterministic interrupt response, on-chip peripherals, and nanoWatt Technology power management for battery-aware applications. PIC18F microcontrollers are 8-bit Harvard-architecture MCUs built around an enhanced instruction set that retains code compatibility with the legacy PIC16 family while adding 16-bit-wide instructions, linear addressing of up to 2 MB, and single-cycle multiply for DSP-style math. The PIC18F2X1X/4X1X sub-family adds a 10-bit A/D converter, an internal oscillator block, Fail-Safe Clock Monitor, and two USART modules, positioning it as the workhorse tier between small 8-pin PIC12/16 parts and larger 40-/44-pin PIC18F4X1X devices. The Flash memory is self-programmable in-circuit, enabling bootloader and field-update workflows. Key features include 48KB Flash, 3968 bytes SRAM, 1024 bytes EEPROM, 25 digital I/O pins, a 10-channel 10-bit ADC, two comparators, two USART ports, an MSSP (SPI/I2C) module, two CCP and one Enhanced CCP capture/compare/PWM channels, and a hardware 8x8 multiplier. nanoWatt Technology provides multiple idle and sleep modes, drawing microampere-level standby current, while the Fail-Safe Clock Monitor automatically switches to the internal RC oscillator if the primary crystal fails for safety-critical loops. The architecture pairs a 16-bit instruction word with an 8-bit data path, so 1 MIPS roughly equals 1 MHz of clock for legacy code and the enhanced core adds single-cycle branches and table reads/writes that allow constant data to live in program memory for compiler-driven table-driven I/O. The interrupt controller supports prioritized vectored interrupts with shadow registers, so high-frequency ADC and timer events can preempt background loops without polling overhead, while the hardware multiplier accelerates integer math for digital filtering and motor-control compensators. Typical applications include industrial sensor conditioning, motor control and BLDC commutation, HVAC fan and damper control, USB-HID peripherals on the PIC18F2X1X/4X1X family, automotive body and chassis sub-systems, consumer appliance control boards, and general-purpose data-acquisition front-ends that pair the 10-bit ADC with the two USART links. The 28-SOIC footprint is friendly to hand-soldered prototypes and standard SMT assembly lines, and the wide 4.2-5.5 V supply lets the part run directly from a regulated 5 V rail without an LDO. When designing with the PIC18F2515, place a 100 nF decoupling capacitor within 5 mm of each power pin and tie MCLR through a 10 kohm pull-up; if in-circuit serial programming (ICSP) is required, reserve the PGC/PGD pairs and route them away from switching nodes. Plan for at least 10 KB of Flash margin if you intend to use MPLAB XC8's position-independent optimization or a USB stack on related variants. This page synthesizes distributor pricing, drop-in PIC18F2X1X/4X1X alternatives, and practical design notes, complementing - not duplicating - the manufacturer datasheet.

RFQ Contact
PIC18F2515-I/SP - 8-Bit 40MHz MCU, 48KB Flash, 28-SPDIP | Microchip
PIC18F2515-I/SP

PIC18F2515-I/SP - 8-Bit 40MHz MCU, 48KB Flash, 28-SPDIP | Microchip

The Microchip Technology PIC18F2515-I/SP is an 8-bit RISC microcontroller from the PIC18F2xxx family, operating at up to 40 MHz with 48 KB of Flash program memory and 3968 bytes of RAM, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. The device integrates 25 digital I/O pins, a 10-bit ADC, multiple timers, and serial peripherals including EUSART, I2C (MSSP), and SPI for flexible embedded connectivity. What is a PIC18F microcontroller? The PIC18F family is Microchip's high-performance 8-bit microcontroller line, built on a RISC (Reduced Instruction Set Computer) Harvard architecture. PIC18F MCUs sit above PIC16F parts in the product hierarchy (8-bit microcontroller -> PIC MCU -> Microchip MCU -> embedded microcontroller) and add enhanced instruction set, larger memory, hardware multiplier, and C-friendly architecture while maintaining the classic 8-bit data path. This makes them suitable for applications that need more performance than PIC16F can deliver but do not require 16-bit or 32-bit cores. Key features include 48 KB self-programmable Flash, 1024 bytes of EEPROM, 3968 bytes SRAM, 10-bit ADC with up to 11 channels, two 8-bit and three 16-bit timers, enhanced CCP modules, an Enhanced USART, MSSP supporting both SPI and I2C, and dual analog comparators. The integrated nanoWatt power management block offers multiple idle and sleep modes with typical current draw in microampere range, supporting battery-aware designs. The -I industrial temperature grade of -40C to +85C allows deployment in uncontrolled thermal environments. The PIC18F2515 architecture uses a 16-bit instruction word with an 8-bit data path, single-cycle ALU operations, hardware multiply, and a 32-level hardware stack. The 10-bit ADC supports up to 11 input channels with acquisition time programmable for sensor interfacing. The device is supported by the MPLAB X IDE, MPLAB XC8 compiler, and PICkit / ICD debugger programmers, providing a complete firmware development ecosystem. The 28-SPDIP package is popular for hobbyist prototyping, breadboarding, and through-hole assembly lines where rework and socketed parts are required. Typical applications include industrial control, sensor interfacing, low-cost motor control (BLDC/PWM), USB-less human interface devices, consumer appliance controllers, and battery-powered data loggers. In motor control the CCP/PWM modules generate complementary PWM with dead-band control; in sensor systems the ADC plus EUSART streams measurements to a host; in battery applications the nanoWatt sleep currents extend operating life. When designing with this part, select a low-ESR decoupling capacitor (100 nF ceramic) close to each VDD pin and a bulk capacitor (10 uF) on the main rail. Leave MCLR either tied high through a 10 kohm resistor or driven by the programmer for in-circuit debug, and use the internal oscillator only when timing tolerance is non-critical; otherwise route a crystal on OSC1/OSC2 for accurate UART baud rates. This page synthesizes distributor pricing, drop-in 28-SPDIP alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PIC18F2515T-I/SO - 8-bit 40MHz PIC MCU 48KB Flash 28-SOIC | Microchip
PIC18F2515T-I/SO

PIC18F2515T-I/SO - 8-bit 40MHz PIC MCU 48KB Flash 28-SOIC | Microchip

The Microchip Technology PIC18F2515T-I/SO is an 8-bit RISC PIC18 microcontroller running up to 40MHz, equipped with 48KB of FLASH program memory (24K x 16), 3968 bytes of RAM, and 25 I/O pins, housed in a 28-pin SOIC (SO) package supplied in Tape & Reel form. It operates from a 4.2V to 5.5V supply and provides a rich set of on-chip peripherals including a 10-bit ADC, multiple timers, and standard serial interfaces. Background knowledge: a microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (FLASH or ROM), data memory (RAM), and programmable I/O with on-chip peripherals. The PIC18 family uses an enhanced 8-bit Harvard RISC architecture with a 16-bit instruction word, sitting in the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. The PIC18F2515 belongs to the mid-range performance tier of PIC microcontrollers, designed for control-oriented applications requiring moderate code density and real-time deterministic behavior. Key features include 48KB (24K x 16) of self-programmable FLASH, 3968 bytes of RAM, 256 bytes of EEPROM, 25 digital I/O pins, a 10-bit ADC with multiple channels, two 8-bit and three 16-bit timers, an enhanced USART, MSSP (SPI/I2C), dual analog comparators, and nanoWatt power management with multiple low-power sleep modes. The ICSP (In-Circuit Serial Programming) interface allows in-field firmware updates without removing the device from the board. The PIC18F2515 uses Microchip's standard Harvard architecture with separate code and data buses, providing deterministic 4-cycle instruction execution at the system clock. The FLASH memory supports self-programming under firmware control, enabling bootloader-based firmware updates and nonvolatile data storage. The device supports clock sources including external crystal, external clock, and internal oscillator blocks with PLL, enabling flexible system design. Typical applications include industrial control systems, sensor signal conditioning, low-to-medium complexity motor control, HVAC control boards, smart metering, consumer appliance controllers, USB-interface devices using the parallel port, and general-purpose embedded control. The wide operating temperature range (-40C to +85C industrial grade) suits outdoor and harsh-environment deployments. When designing with this device, ensure decoupling capacitors (100nF ceramic) are placed close to VDD/VSS pairs to maintain ADC accuracy, and verify the oscillator configuration bits match the chosen clock source. The 5V-only supply requirement means level shifters are needed for 3.3V peripherals. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC18F family, and practical design notes not found in the standalone manufacturer datasheet.

RFQ Contact
PIC18F252-E/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip
PIC18F252-E/SO

PIC18F252-E/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip

The Microchip Technology PIC18F252-E/SO is an 8-bit RISC Flash microcontroller based on the PIC18 CPU core, delivering up to 40 MHz (10 MIPS) operation, 32 KB of Flash program memory and 1.5 KB of RAM in a 28-pin SOIC package. It features 256 bytes of EEPROM, 23 digital I/O lines, four timer modules, two CCP/PWM channels, a 10-bit multi-channel Analog-to-Digital converter, and configurable synchronous serial ports that operate as either 3-wire SPI or 2-wire I2C. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data-path CPU with on-chip program memory, data memory and peripheral interfaces. Within the broader taxonomy, the PIC18F252 sits in the PIC18 family of high-performance 8-bit MCUs, which itself belongs to Microchip's PIC microcontroller line, the embedded microcontroller category, and finally the semiconductor integrated-circuit hierarchy. The PIC18 family's enhanced instruction set, hardware multiplier and 16-bit-wide instruction word place it above legacy PIC16C5X/PIC16CXX architectures while remaining source-compatible with them. Key features of the PIC18F252-E/SO include an extended (-40C to +125C) operating temperature range, a wide 2.0 V to 5.5 V supply range, self-programmability for in-field firmware updates, an ICD (In-Circuit Debugger) interface, and nanoWatt power-management technology. Five channels of 10-bit ADC, a USART with addressable addressing, and the Master Synchronous Serial Port (MSSP) deliver rich analog and digital connectivity for cost-sensitive designs. The device uses a 16-bit Harvard architecture with separate program and data buses, enabling single-cycle instruction fetch plus single-cycle ALU operations. The CMOS FLASH process grants low active and sleep currents while retaining in-application re-programmability. Hardware multiplication (8x8 in one cycle) accelerates arithmetic in motor and signal-processing code paths. Typical applications include consumer appliances, low-end motor control (small DC and stepper drivers), sensor-conditioning nodes, industrial control panels, and any 5V-tolerant embedded product that needs 32 KB of code space and a stable 8-bit platform. Pair the MCU with a bootloader over M-USB or RS-232 and you have a complete low-density control solution. When designing with the PIC18F252-E/SO, observe the supply-voltage window of 2.0-5.5 V (4.2-5.5 V is typical for -E parts in industrial applications). Place a 0.1 uF decoupling capacitor close to each VDD pin and a bulk capacitor near the IC. Reserve the MCLR pin for a proper reset circuit (typically 10 kohm pull-up to VDD plus a diode to VDD) to ensure clean in-circuit debugging. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet alone, and is structured for AI search engines (AEO/GEO) so engineers can find answers in the FAQ and application sections without scrolling through full documents.

RFQ Contact
PIC18F252-E/SP - 8-Bit MCU, 32KB Flash, 40MHz, SPDIP-28 | Microchip
PIC18F252-E/SP

PIC18F252-E/SP - 8-Bit MCU, 32KB Flash, 40MHz, SPDIP-28 | Microchip

The Microchip Technology PIC18F252-E/SP is an 8-bit CMOS flash microcontroller from the PIC18F family, delivered in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It integrates 32KB of program flash memory organized as 16K x 16 words, 1.5KB (1536 bytes) of SRAM, 256 bytes of EEPROM data memory, and a 40 MHz (10 MIPS) enhanced Harvard RISC core. The integrated peripherals include 23 digital I/O lines, a 10-bit multi-channel Analog-to-Digital Converter (ADC), two Capture/Compare/PWM (CCP) modules, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), a Master Synchronous Serial Port (MSSP) configurable as SPI or I2C, and an in-circuit debugger. What is a PIC18F microcontroller? PIC18F is Microchip Technology's family of high-performance 8-bit Reduced Instruction Set Computer (RISC) microcontrollers built on a Harvard memory architecture. They sit within the broader 8-bit MCU taxonomy (MCU -> microcontroller -> 8-bit MCU -> RISC MCU -> Harvard architecture MCU -> embedded controller) and target applications needing moderate computational throughput, low power, abundant peripherals, and broad developer tool support including MPLAB X IDE, XC8 compilers, and PICkit debuggers. Key technical features of the PIC18F252-E/SP include the self-programmable flash permitting in-field firmware updates, C compiler-optimized instruction set with 77 single-word instructions, an extended instruction set variant, and wide 4.2V to 5.5V supply tolerance. The -E temperature grade spans -40C to +125C, qualifying the device for industrial and harsh-environment use. The 28-pin SPDIP-28 (SP) form factor suits breadboarding, legacy designs, through-hole manufacturing, and hand-soldered prototypes where SMD reflow is impractical. Architecturally, PIC18F252-E/SP combines an 8-bit data path with a 16-bit instruction word, two address spaces for program and data memories, hardware multiplier for single-cycle 8x8 operations, and a vectored interrupt controller with prioritized sources. Two CCP modules can be configured for PWM, capture, or compare, enabling motor control, timing measurement, and waveform generation. The MSSP supports both SPI (4-wire with separate I/O) and I2C (master/slave, 7/10-bit addressing), giving designers a flexible peripheral mix. Typical applications include industrial control systems, HVAC thermostats, sensor signal conditioning, low-end motor drivers, instrumentation, and consumer appliances. The PIC18F252-E is well suited for designs migrating from PIC16F parts that need more code space, additional I/O, or higher ADC resolution. A key design consideration when selecting this part is its wide operating voltage range combined with high ADC accuracy. Unlike newer nanoWatt XLP PIC18FxxKxx series, the 'F252 draws higher active current but offers mature code libraries, broad toolchain support, and an extensive base of proven reference designs. This page synthesizes verified distributor pricing, official Microchip datasheet parameters, drop-in alternatives in the same 28-pin footprint, and practical design notes beyond those found in the manufacturer datasheet.

RFQ Contact
PIC18F252-I/SO - 8-bit 40MHz 32KB Flash MCU | Microchip | 28-SOIC
PIC18F252-I/SO

PIC18F252-I/SO - 8-bit 40MHz 32KB Flash MCU | Microchip | 28-SOIC

The Microchip Technology PIC18F252-I/SO is a high-performance 8-bit CMOS Flash microcontroller built on Microchip's PIC18 architecture, delivering 10 MIPS throughput (40 MHz max clock, 100 ns instruction cycle) in a 28-pin SOIC package with industrial -40C to +85C temperature rating. A microcontroller (MCU) is a single-chip computer integrating a CPU core, program memory (Flash/ROM), data memory (RAM/EEPROM), and programmable I/O peripherals on one die. PIC microcontrollers sit at the foundation of embedded control, spanning consumer appliances, automotive body electronics, industrial sensors, and medical devices - the 8-bit PIC18 family specifically targets applications needing higher performance and more peripherals than the baseline PIC16 family while remaining easy to program in C. Key features of the PIC18F252 include 32 KB of on-chip Flash program memory (16K x 16 words), 1536 bytes of SRAM, 256 bytes of EEPROM for non-volatile data storage, 23 digital I/O pins, a 10-bit A/D converter with up to 5 input channels, two Capture/Compare/PWM (CCP) modules, an enhanced USART, a Master Synchronous Serial Port (MSSP) configurable as SPI or I2C, and 4 timer modules. The C-compiler-friendly instruction set comprises only 77 single-word instructions, while 16-bit instructions and hardware multiply deliver the throughput advantage over the PIC16 line. The PIC18F252 architecture uses a Harvard memory layout with separate program and data buses, allowing instruction fetch and operand read in the same cycle. Self-programming support lets the device update its own Flash in-field, and an integrated ICD (In-Circuit Debug) interface simplifies bring-up. Operating from 4.2 V to 5.5 V, it consumes approximately 16 mA at 40 MHz in active mode and drops below 1 uA in sleep. Typical applications include industrial sensor signal conditioning, automotive body modules and instrument clusters, HVAC controllers, security alarm panels, white-goods motor control, low-end instrumentation with ADC front-ends, and USB-to-serial bridges when paired with a peripheral PHY. Designers also use the PIC18F252 in replacement of older PIC16 designs where the 16-bit instruction set, additional RAM, and enhanced peripherals unlock new features without learning a new toolchain. Design considerations include decoupling: a 100 nF ceramic should sit within 5 mm of each power pair (VDD/VSS, AVDD/AVSS), with a bulk 10 uF near the IC. The MCLR reset pin must have a 10 kohm pull-up unless tied to a supervisor; for ICSP programming, isolate the MCLR line with a resistor divider. Unused A/D channels should be tied to ground to avoid shoot-through current. This page combines DigiKey/Mouser pricing, Microchip product-page facts, and practical design notes curated for engineers evaluating the PIC18F252-I/SO against newer PIC18 K-series and K42 alternatives.

RFQ Contact
PIC18F2520-E/SO - 8-bit 25MHz 32KB Flash MCU 28-SOIC | Microchip
PIC18F2520-E/SO

PIC18F2520-E/SO - 8-bit 25MHz 32KB Flash MCU 28-SOIC | Microchip

The Microchip Technology PIC18F2520-E/SO is an 8-bit PIC18F microcontroller (MCU) delivering up to 25 MHz CPU clock (40 MHz oscillator input, equivalent to 10 MIPS of CPU performance at 40 MHz / 16 MIPS at the datasheet maximum instruction rate of 200 ns) with 32 KB of on-chip flash program memory and 1.5 KB of RAM, housed in a 28-pin SOIC (SO) package. A PIC18F microcontroller is an enhanced 8-bit Harvard-architecture RISC core in Microchip's PIC18 family. The PIC18F series adds 16-bit wide instructions and a linear program-memory space on top of the legacy PIC16 architecture, while preserving byte-oriented register access. This particular part targets cost-sensitive embedded control applications that need more program space, more I/O, and richer peripherals than the PIC16F family, without moving to a 16-bit MCU. It sits inside the broader microcontroller hierarchy as: 8-bit MCU -> PIC18 family -> PIC18F2xxx sub-family (28-40-44-pin devices) -> PIC18F2520 specifically. Key differentiating features include 10-bit analog-to-digital conversion (ADC) with up to 10 input channels, nanoWatt Technology power management for reduced active and sleep currents, an enhanced addressable USART, MSSP serial port supporting SPI and I2C (master/slave), capture/compare/PWM (CCP) modules, and 25 I/O pins with individual pull-up control. The on-chip debug (ICD) capability and self-programmability make field firmware updates possible without an external programmer. Architecturally, the device uses a 16-bit wide instruction set with an 8-bit data path, a 31-level hardware stack, and a priority-level interrupt controller. nanoWatt Technology adds multiple low-power modes (Run, Idle, Sleep and several oscillator-tunable variants), allowing the designer to trade CPU throughput for current consumption in battery-powered nodes. Typical applications include industrial control and sensor-interface modules, home-automation and building-control nodes, low-cost motor-control signal chains, USB HID bridges (when paired with the PIC18F2550/4550 variant), embedded data acquisition, and consumer appliances requiring reliable 5 V CMOS logic. The PIC18F2520-E/SO is the "E" (Extended) temperature grade variant rated for -40 to +125 C, suitable for industrial environments. When designing with this part, select decoupling per Microchip's PIC18F2520 datasheet, observe VDD/VSS analog and digital pin separation, and use the MPLAB XC8 compiler with the PIC18 configuration-bit pragma to lock oscillator, watchdog and brown-out behavior at build time. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for engineers evaluating the PIC18F2520-E/SO in production designs.

RFQ Contact
PIC18F2520-E/SP - 8-bit MCU, 32KB Flash, 28-SPDIP | Microchip
PIC18F2520-E/SP

PIC18F2520-E/SP - 8-bit MCU, 32KB Flash, 28-SPDIP | Microchip

The Microchip PIC18F2520-E/SP is an 8-bit PIC18F-series enhanced flash microcontroller built on a RISC architecture and housed in a 28-pin SPDIP through-hole package. It integrates 32KB of program Flash, 3968 bytes of RAM and 256 bytes of EEPROM, runs at up to 40 MHz (10 MIPS), and operates from 2.0V to 5.5V across the extended -40C to +125C industrial temperature range. The part suffix "-E" designates the extended-temperature grade, while "/SP" denotes the 28-pin Skinny Plastic DIP. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and a fixed set of peripherals (I/O, timers, ADC, communication) into one package. PIC microcontrollers use a Harvard RISC architecture with a small, fixed instruction set optimized for C code generation, sitting in the broader hierarchy: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor device. Key specifications include 25 digital I/O pins, a 10-bit ADC with up to 10 input channels, two 8-bit and three 16-bit timers, two USART modules, one MSSP (SPI/I2C) peripheral, two analog comparators, and a nanoWatt power-managed sleep mode drawing sub-microamp currents. The enhanced flash supports in-circuit serial programming (ICSP) via two pins, enabling field firmware updates without removing the part from the board. The 28-pin SPDIP package is preferred for hobbyist, educational, and through-hole prototype designs, while SOIC, QFN and QFP variants cover surface-mount boards. Hardware features such as the Fail-Safe Clock Monitor, Watchdog Timer with dedicated RC oscillator, and wide operating voltage make the PIC18F2520-E/SP a robust general-purpose choice for embedded control applications. Typical uses include industrial sensor interfaces, motor control signal conditioning, consumer appliance control boards, HVAC thermostats, and battery-powered instrumentation. The combination of nanoWatt low-power modes and AC-driven operation makes the part flexible for both line-powered and energy-harvesting designs. When designing with this MCU, note that the SPDIP package requires through-hole PCB layout; for reflow-soldered production, use the SO or QFN equivalents in the same PIC18F2520 family. Always provide a 100 nF decoupling capacitor adjacent to VDD and ensure the MCLR reset circuit uses a 10 kohm pull-up with a diode to VDD to allow in-circuit programming. This page synthesizes drop-in alternatives in the same 28-SPDIP footprint, application notes, and pricing not found in a single distributor listing.

RFQ Contact
PIC18F2520-I/ML - 8-Bit 40MHz 32KB Flash MCU 28-QFN | Microchip
PIC18F2520-I/ML

PIC18F2520-I/ML - 8-Bit 40MHz 32KB Flash MCU 28-QFN | Microchip

The Microchip Technology PIC18F2520-I/ML is a high-performance 8-bit PIC18-family flash microcontroller offering 32 KB of program Flash memory, 1536 bytes of SRAM, and 256 bytes of EEPROM, housed in a 28-pin QFN (ML) 6x6 mm package with exposed thermal pad. It executes instructions in 200 ns (10 MIPS) through an enhanced RISC architecture, supports 25 digital I/O pins, and integrates a 10-bit ADC with up to 13 input channels plus a full set of nanoWatt power-management modes for energy-conscious designs. What is a PIC18 microcontroller? An 8-bit microcontroller is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), non-volatile data memory (EEPROM), and configurable peripherals on one silicon die. The PIC18 family from Microchip is the high-tier of the 8-bit PIC line, providing an enhanced instruction set, linear memory addressing, C-compiler-friendly architecture, and prioritized interrupts. Within the embedded taxonomy, the PIC18F2520 sits between baseline PIC10/12/16 parts and the 16-bit dsPIC/PIC24 line, balancing code density, peripheral count, and low-power features for industrial, consumer, and automotive-body applications. Key features include 40 MHz operation from a 4.2 V to 5.5 V supply, 10-bit ADC with 13 channels, an EUSART with LIN support, MSSP (SPI/I2C), two enhanced CCP modules, and nanoWatt sleep modes that drop supply current into the nanoamp range. The QFN-28 (ML) package offers a compact 6x6 mm footprint with an exposed die pad for thermal dissipation. The part is rated for the industrial -40C to +85C temperature range. The PIC18F2520 combines PIC18 legacy peripherals with code protection, ICSP (In-Circuit Serial Programming), and a 10-bit ADC capable of approximately 100 Ksps conversion. Its instruction set supports 75 instructions with 83 enhanced opcodes, enabling efficient C compilation while maintaining predictable interrupt latency. Internal oscillator and PLL options reduce external component count in cost-sensitive designs. Typical applications include industrial control systems, automotive body electronics, sensor interfacing, low-power remote sensors, motor control, and UART-to-UART bridges when paired with an external transceiver. The 32 KB Flash also suits small appliances and HVAC controllers. When designing with the PIC18F2520, place 100 nF decoupling on every VDD/VSS pair, route PGC/PGD ICSP lines to test pads for field update, and solder the exposed pad to a sufficient copper area. Configuration bits must be set to enable or disable features such as watchdog timer, low-voltage programming, and code protection per application security requirements. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not collected in any single Microchip datasheet, helping engineers select and source the PIC18F2520-I/ML with confidence.

RFQ Contact
PIC18F2520-I/SO - 8-bit MCU, 32KB Flash, 40MHz, 28-SOIC | Microchip
PIC18F2520-I/SO

PIC18F2520-I/SO - 8-bit MCU, 32KB Flash, 40MHz, 28-SOIC | Microchip

The Microchip Technology PIC18F2520-I/SO is an 8-bit PIC18 enhanced-flash microcontroller delivering up to 10 MIPS performance with 32KB (16K x 16) of on-chip Flash program memory, 1.5KB of RAM, and 256 bytes of EEPROM, packaged in a 28-pin SOIC (SO) wide-body surface-mount package. It integrates a 10-bit, up-to-10-channel Analog-to-Digital Converter (ADC), nanoWatt power-management technology, an internal oscillator from 31 kHz to 8 MHz, and a hardware 8x8 single-cycle multiplier, making it well suited for cost-sensitive, mixed-signal embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a configurable set of digital and analog peripherals around a shared internal bus. The PIC18F family uses an enhanced RISC Harvard architecture with a C-compiler-optimized instruction set, sitting within the broader Microchip MCU taxonomy of PIC10/12/16/18/24/32 8-/16-/32-bit families, which themselves belong to the wider category of microcontrollers -> microprocessors -> semiconductors. By combining analog integration with the ADC, PWM, USART, MSSP (SPI/I2C) and nanoWatt sleep modes, PIC18F MCUs often eliminate external glue logic and analog front-end components in small-form-factor products. Key features include 40 MHz (10 MIPS) CPU speed from a 4.2 V to 5.5 V supply, 25 digital I/O pins, an internal RC oscillator selectable from 31 kHz to 8 MHz, a Fail-Safe Clock Monitor that allows safe shutdown on clock failure, a separate RC-oscillator-backed Watchdog Timer, and CTMU / nanoWatt technology for ultra-low standby current. On-chip peripherals include an Enhanced CCP, two comparators, a 10-bit ADC with up to 10 channels, MSSP (SPI/I2C), and an Enhanced USART. Typical applications include industrial control, sensor conditioning, automotive body electronics, low-cost data loggers, and USB/HID-less human-interface products. The wide 5 V supply range and rich analog integration make the device a common choice for 5V-tolerant legacy systems that need more performance than a PIC16F but want to stay inside the 8-bit toolchain ecosystem (MPLAB X IDE, XC8 compiler, MPLAB PICkit 5). When designing with this part, plan oscillator stability for low-power modes (use the internal 31 kHz LP oscillator for sleep), keep Vdd decoupling tight to the SOIC pins, and route the ADC reference pins with a low-impedance ground return to preserve ADC accuracy.

RFQ Contact
PIC18F2520-I/SP - 8-bit 40MHz 32KB Flash MCU | Microchip | 28-SPDIP
PIC18F2520-I/SP

PIC18F2520-I/SP - 8-bit 40MHz 32KB Flash MCU | Microchip | 28-SPDIP

The Microchip Technology PIC18F2520-I/SP is an 8-bit PIC18F-family Flash microcontroller running at up to 40 MHz (10 MIPS), integrating 32 KB of program Flash, 1536 bytes of SRAM, and 256 bytes of EEPROM in a 28-pin SPDIP (0.300 inch, 7.62 mm) through-hole package. It exposes 25 general-purpose I/O pins and includes a 10-bit ADC, multiple capture/compare/PWM modules, and the nanoWatt power-managed sleep modes that define the PIC18F2520 generation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and configurable peripherals such as ADC, PWM, timers, and serial interfaces. Within the broader taxonomy, the PIC18F2520 belongs to the 8-bit MCU class, sits in the PIC18 enhanced RISC family, and is positioned by Microchip between baseline PIC10/12/16 parts and the 16-bit dsPIC/PIC24 line. The 28-pin SPDIP variant is the classic DIP-28 form factor used for prototyping, breadboarding, and legacy industrial controller cards where socketed replacement is desirable. Key features include a C-optimized enhanced Harvard architecture with 8x8 single-cycle hardware multiply, an internal oscillator block covering 31 kHz to 8 MHz, a Fail-Safe Clock Monitor, two 8-bit and three 16-bit timers, an Enhanced Capture/Compare/PWM (ECCP) module, two MSSP blocks supporting SPI and I2C (master/slave), an Enhanced USART, 10-bit ADC with up to 10 channels, two analog comparators, and a programmable Low-Voltage Detect module. The on-board nanoWatt technology offers Idle, Sleep, and low-power Timer1 oscillator operation. Typical applications include industrial control panels, motor drive signal conditioning, sensor interface boards, low-power remote sensor nodes, legacy PIC18 firmware upgrades that need more Flash and peripherals than older PIC16 designs, and educational kits where the SPDIP-28 footprint simplifies breadboard use and socketed replacement. Designers should provide a stable 4.2 V to 5.5 V supply, place a 100 nF decoupling capacitor close to VDD, route MCLR with a 10 kohm pull-up, and budget for the in-circuit serial programming (ICSP) header required by PICkit programmers. Industrial-temperature (-40C to +85C) operation is supported. This page consolidates verified distributor pricing, drop-in pin-compatible alternatives in the SPDIP-28 footprint, and application guidance drawn from the Microchip PIC18F2420/2520/4420/4520 datasheet that the bare DigiKey or Mouser listing does not provide.

RFQ Contact
PIC18F2520T-I/ML - 8-bit MCU, 32KB Flash, 40MHz, 28-QFN | Microchip
PIC18F2520T-I/ML

PIC18F2520T-I/ML - 8-bit MCU, 32KB Flash, 40MHz, 28-QFN | Microchip

The Microchip Technology PIC18F2520T-I/ML is an 8-bit PIC18F-family flash microcontroller running up to 40 MHz (10 MIPS with 4x PLL active) and integrating 32 KB of Flash program memory plus 1.5 KB of data EEPROM, packaged in a 28-pin QFN (ML, 6x6 mm) with 25 digital I/O pins. The device operates across an industrial temperature range of -40 °C to +85 °C with a supply voltage of 4.2 V to 5.5 V (a 2.0 V–5.5 V "LF" variant also exists, but the "I/ML" suffix denotes the standard 4.2 V minimum version). What is a PIC18 microcontroller? The PIC18 is Microchip's high-end 8-bit RISC architecture family, positioned above PIC16 and below the 16-bit dsPIC33/PIC24 line. PIC18 parts combine a Harvard bus, a 16-bit instruction word with 8-bit data path, hardware multiply, a C-optimized instruction set and self-programmable Flash, making them suited to mid-range embedded control where deterministic timing, peripheral richness and stable firmware updates are required. Key features of the PIC18F2520 include 1.5 KB SRAM (plus 1.5 KB general-purpose EEPROM), a 10-bit ADC with up to 10 input channels, one Enhanced USART, one MSSP (SPI/I2C), two CCP and one Enhanced CCP module, two 8-bit and three 16-bit timers, nanoWatt power management, an ICD/ICSP debug interface, and 25 mA source/sink capability on each I/O with internal weak pull-ups. The wide operating range and peripheral set target appliance control, sensing, motor pre-driver, lighting, USB-serial bridge co-processors and field-replaceable industrial nodes. According to the manufacturer datasheet, the device is qualified to AEC-Q100 for automotive PIC18F2520-I/ML variants. Architecture-wise, the PIC18F2520 uses a 16-bit wide instruction pipeline with 31-level hardware stack, hardware multiply (8x8 in one cycle), 10-bit pipelined ADC with internal 4-channel mux and self-calibration, and a low-power "nanoWatt" feature set including run, idle, sleep and a 32 kHz secondary oscillator with Timer1 real-time clock operation. Multiple oscillator modes (HS, XT, LP, RC, EC, INTIO) plus 4x PLL on the standard 40 MHz silicon allow flexible clocking from internal 31 kHz through external 40 MHz sources. Typical applications span USB HID class devices, industrial control panels, sensor signal conditioning, automotive body and HVAC ECUs (Q-graded), white goods motor control, smart metering, lighting ballasts, and embedded data logging. The 28-QFN variant (PIC18F2520T-I/ML, T = Tape & Reel) is favored where board height is constrained. A critical design consideration: the PIC18F2520 I/O banks are not 5 V-tolerant when the part is supplied below 4.2 V, so do not drop to 3.3 V operation on this "I/ML" version; either use a 5 V rail or move to the PIC18LF2520. Decoupling requires one 100 nF X7R cap per supply pin and a 10 µF bulk capacitor, with the Vcap pin on PIC18F core regulated devices carrying 8 µF–12 µF for the internal 2.5 V regulator. Trace lengths to MCLR must be short to prevent in-circuit debug noise. This page synthesizes real distributor pricing, a same-family drop-in matrix, and design considerations that go beyond the manufacturer datasheet — including migration paths between PIC18F2520 and PIC18LF2520 and QFN-28 package decisions versus the SPDIP/SOIC siblings.

RFQ Contact
PIC18F2520T-I/SO - 8-bit 40MHz 32KB Flash MCU | Microchip
PIC18F2520T-I/SO

PIC18F2520T-I/SO - 8-bit 40MHz 32KB Flash MCU | Microchip

The Microchip PIC18F2520T-I/SO is an 8-bit PIC18F microcontroller IC running up to 40MHz (10 MIPS) with 32KB (16K x 16) of Flash program memory and 3968 bytes of RAM, packaged in a 28-pin SOIC (SO) wide-body package. It includes an integrated 10-bit ADC and integrates Microchip's nanoWatt power-managed technology family for low-power applications. The 'T' suffix indicates tape and reel packaging, and the 'I' indicates the -40C to +85C industrial temperature range. This device belongs to the Enhanced Flash Microcontroller family - a category of 8-bit MCUs based on an advanced RISC Harvard architecture with 8x8 single-cycle hardware multiply. The PIC18F family is part of Microchip's broader PIC microcontroller hierarchy (PIC > PIC18 > PIC18F2x20) and is widely deployed in cost-sensitive embedded designs that need precise I/O control, deterministic real-time response, and low active/standby current draw. The 28-pin SOIC form factor is one of the most common surface-mount footprints for industrial controllers. Key features include 25 digital I/O pins, an internal 31 kHz to 8 MHz oscillator, fail-safe clock monitor with safe shutdown on clock failure, a separate-oscillator watchdog timer with on-chip RC, and hardware peripherals including 10-bit ADC, comparators, PWM, and USART. According to the Microchip datasheet (DS39667), the device operates from 4.2V to 5.5V and supports in-circuit serial programming (ICSP) and in-circuit debugging (ICD). Typical applications include industrial control panels, automotive body and convenience electronics, sensor signal conditioning nodes, motor control sub-systems, USB-to-UART bridging via companion transceivers, and home appliance user-interface boards. The internal oscillator and wide temperature range make it suited for unattended installations. When designing with this device, ensure decoupling on every VDD/AVDD pin (100 nF minimum plus a bulk 10 uF), follow Microchip's recommended ICSP ICP layout for in-circuit programming access, and budget the ADC sampling time against the internal TAD clock to keep conversion errors below 1 LSB.

RFQ Contact
PIC18F2523-E/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip
PIC18F2523-E/SO

PIC18F2523-E/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip

The Microchip Technology PIC18F2523-E/SO is a high-performance 8-bit RISC flash microcontroller featuring 32KB of program memory, 1.5KB of RAM, and a 12-bit ADC with up to 10 channels, packaged in a 28-pin SOIC (SO) wide-body IC. The device operates from a 4.2V to 5.5V supply and supports clock speeds up to 40MHz (10 MIPS), making it well suited for embedded control applications requiring deterministic real-time response and on-chip analog integration. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), working memory (RAM), and a rich set of peripherals on a single silicon die. Within the broader semiconductor taxonomy, an MCU belongs to the family of embedded processors, sitting between simple digital logic ICs and full application processors. PIC18F devices specifically employ an enhanced Harvard RISC architecture with a C-compiler-friendly instruction set, hardware 8x8 single-cycle multiplication, and a priority-level interrupt controller that simplify firmware development for real-time embedded products. The PIC18F2523 distinguishes itself with a 12-bit ADC (vs. 10-bit on older PIC18F parts), an internal oscillator block tunable from 31 kHz to 8 MHz and up to 32 MHz via 4x PLL, a Fail-Safe Clock Monitor that permits safe shutdown on clock loss, an Enhanced Capture/Compare/PWM (ECCP) module, and three 16-bit timers. The wide-body 28-SOIC footprint offers generous board-level handling for industrial temperature grades (-40C to +125C) and through-hole-style manufacturing flows. Typical applications include industrial sensor signal conditioning, motor control loops (BLDC, stepper, brushed DC via PWM), home-automation user interfaces, automotive body and HVAC modules, USB-to-UART bridging front ends, and general-purpose embedded control. The on-chip 12-bit ADC removes the need for an external converter when interfacing with analog sensors, reducing BOM cost and PCB area. Designers should review the PIC18F2523 datasheet for the pin-compatibility migration path to the PIC18F25K22 family when modernized peripherals, lower power, and CIP (Core Independent Peripherals) are desired. The E suffix denotes the -40C to +125C extended temperature grade, and the /SO suffix denotes the 28-pin wide-body SOIC package. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC18F2523-E/SP - 8-Bit MCU 32KB Flash 40MHz 28-SPDIP | Microchip
PIC18F2523-E/SP

PIC18F2523-E/SP - 8-Bit MCU 32KB Flash 40MHz 28-SPDIP | Microchip

The Microchip PIC18F2523-E/SP is an 8-bit PIC18-family microcontroller with 32 KB of Flash program memory and 1.5 KB of RAM, powered by an enhanced RISC architecture and housed in a 28-pin SPDIP (Skinny Plastic Dual In-line Package). It executes up to 10 MIPS at 40 MHz and supports a 2.0 V to 5.5 V operating voltage range, providing 25 digital I/O pins for general-purpose use. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile RAM, and a rich set of on-chip peripherals (A/D converters, timers, communication controllers, and I/O). The PIC18F family sits above the PIC16 entry-level line in Microchip's taxonomy, offering more memory, more peripherals, and faster instruction throughput. It belongs to the broader 8-bit MCU class (PIC18 -> 8-bit PIC -> microcontroller -> embedded computing -> semiconductor), designed to bridge the gap between simple 8-bit control loops and higher-performance 16-/32-bit cores at very low cost and power. The PIC18F2523's headline features include hardware single-cycle 8x8 multiplication, an internal oscillator that can be tuned from 31 kHz to 8 MHz (and up to 32 MHz with the 4x PLL), a Fail-Safe Clock Monitor that safely shuts the system down if the primary clock is lost, an enhanced addressable USART, MSSP with I2C and SPI support, a 12-bit A/D converter with up to 10 channels, and nanoWatt power-management modes for energy-sensitive applications. An enhanced 16-bit capture/compare/PWM module supports motor-control and lighting use cases. The -E suffix designates the extended temperature grade (-40 °C to +125 °C), and the -40 MHz / 40 MHz operation is the standard rate; the extended-grade die is specified across automotive and industrial ranges. The architecture uses a Harvard memory layout with separate program and data buses, a 16-bit instruction word, and an instruction pipeline that lets most operations complete in one cycle. Hardware multiplier support and the C-optimized instruction set accelerate the kind of byte- and bit-level DSP work common in consumer and industrial control loops. Code protection, a separate watchdog timer with its own on-chip low-power RC oscillator, and In-Circuit Serial Programming (ICSP) complete the picture. Boot memory region and configuration-word protection safeguard against accidental reprogramming in the field. Typical applications include industrial control panels, building automation sensor nodes, low-end motor drivers and appliance controllers, USB-to-UART bridges (when paired with the PIC18F family USB-capable siblings), temperature and pressure monitoring devices, automotive interior modules (under -E temperature grade), and consumer devices that benefit from generous Flash and reliable analog peripherals. The 12-bit ADC and nanoWatt modes are particularly useful for battery-powered instrumentation. Designers should note that pin ordering and package suffix matter: the -E/SP part is the extended-temperature SPDIP variant, while -E/SO is the wide-SOIC package and -E/ML is the QFN. All three are code-compatible; the only practical difference is the PCB footprint. When migrating between them, ensure the lead-free solder process and the in-circuit programming header are repackaged accordingly. This page bundles distributor pricing, real drop-in alternatives, and PCB-level design guidance that aren't visible from the manufacturer datasheet alone, giving engineers a single starting point for selecting and qualifying the PIC18F2523-E/SP for volume production.

RFQ Contact
PIC18F2523-I/ML - 8-Bit MCU, 32KB Flash, 12-bit ADC, 28-QFN | Microchip
PIC18F2523-I/ML

PIC18F2523-I/ML - 8-Bit MCU, 32KB Flash, 12-bit ADC, 28-QFN | Microchip

The Microchip PIC18F2523-I/ML is a high-performance 8-bit PIC18 microcontroller IC delivering 40 MHz (10 MIPS) CPU performance with 32KB (16K x 16) of Enhanced Flash program memory and 1536 bytes of RAM, housed in a 28-pin QFN (6x6 mm) package with exposed thermal pad. The -I suffix denotes the industrial operating temperature grade (-40C to +85C), and the /ML suffix indicates the QFN surface-mount package option. A PIC18 microcontroller belongs to Microchip's 8-bit RISC architecture family - specifically the enhanced PIC18F2xxx/4xxx series introduced as successors to the original PIC16 mid-range parts. These microcontrollers combine Harvard bus architecture (separate program and data memory buses) with a C-optimized instruction set, hardware 8x8 single-cycle multiplier, and an internal oscillator block that supports 31 kHz to 8 MHz directly, up to 32 MHz when paired with the 4X PLL. PIC18 devices sit within the broader taxonomy of microcontroller -> embedded controller -> semiconductor IC. Key features of the PIC18F2523 include 25 digital I/O pins, a 10-channel 12-bit Analog-to-Digital Converter (ADC), nanoWatt power management for sleep currents under 1 uA, Capture/Compare/PWM modules, Master Synchronous Serial Port (MSSP) supporting SPI and I2C, enhanced USART, two analog comparators, and a Fail-Safe Clock Monitor that safely shuts the system down if the primary clock source fails. The device operates from 4.2V to 5.5V and supports self-programmability of its Flash memory. Technically, the PIC18F2523 uses C compiler-optimized RISC architecture with a 16-bit instruction word (vs the 14-bit PIC16 instruction width), giving higher code density and richer addressing modes. The 12-bit ADC is a major upgrade over the 10-bit ADC in earlier PIC18F2x20 parts, doubling the conversion resolution (4096 steps vs 1024) and enabling precision sensor readout. The internal oscillator with 4X PLL provides a low-BOM-count path to high-frequency operation without external crystals. Typical applications include industrial control panels, sensor signal conditioning with on-board ADC, motor control via the CCP/PWM modules, USB/HID peripherals (using a companion USB PIC), automotive body electronics, and consumer appliance controllers. The nanoWatt technology makes the part particularly attractive for battery-powered or energy-harvesting designs that spend long periods in sleep mode. When designing with the PIC18F2523, ensure that the exposed thermal pad of the QFN-28 package is soldered to the PCB ground plane for proper heat dissipation and mechanical stability. The ICSP (In-Circuit Serial Programming) pins must be routed to a header or test pad to allow firmware updates in production without removing the part from the board. This page synthesizes verified Microchip datasheet specifications, current distributor pricing tiers, drop-in alternatives in the PIC18 family, and practical design notes not aggregated on individual distributor product pages.

RFQ Contact
PIC18F2523-I/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip
PIC18F2523-I/SO

PIC18F2523-I/SO - 8-Bit 40MHz 32KB Flash MCU 28-SOIC | Microchip

The Microchip Technology PIC18F2523-I/SO is an 8-bit PIC18 enhanced flash microcontroller IC running at up to 40MHz, integrating 32KB (16K x 16) of program flash memory and packaged in a 28-pin SOIC (SO) wide-body package. It belongs to the PIC18F2x23/4x23 family, which combines high computational performance with nanoWatt power management and a 12-bit A/D converter for mixed-signal embedded designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripheral interfaces on one die; the PIC18 family uses a RISC-based architecture with hardware multiply, providing deterministic instruction execution and C-compiler-friendly performance for embedded control applications. Key features of the PIC18F2523 include 1536 bytes of RAM, 256 bytes of EEPROM, 25 digital I/O pins, 10-channel 12-bit A/D converter, two CCP modules, one Enhanced CCP (ECCP), two comparators, a USART with LIN support, an MSSP (SPI/I2C) port, and an internal oscillator block programmable from 31 kHz to 8 MHz (and up to 32 MHz with the 4X PLL). The nanoWatt technology adds multiple power-managed modes for battery-aware designs. Architecturally the device uses a 16-bit wide instruction word, an 8-bit data path, a hardware 8x8 multiplier (single-cycle), and a 31-level hardware stack. The 12-bit ADC supports up to 12 input channels on larger pin-count variants, enabling sensor conditioning and motor-control feedback loops in a single chip. Typical applications include industrial sensor interfaces, automotive body and HVAC control, appliance control panels, low-power remote sensor nodes, USB/serial bridging using the USART, and small motor drivers via CCP/PWM. The wide 2.0V-5.5V operating range also makes it attractive for portable battery-powered products. When designing with this part, place decoupling capacitors (100 nF and 10 uF) within 5 mm of VDD/AVDD, tie MCLR through a 10 kohm pull-up to VDD, and ensure the 28-SOIC footprint accommodates a 300-mil wide-body SO land pattern for proper soldering. This page consolidates current distributor pricing, drop-in PIC18F alternatives, and practical design notes beyond what the Microchip datasheet alone provides.

RFQ Contact
PIC18F2523-I/SP - 8-bit 32KB Flash MCU, 28-SPDIP | Microchip
PIC18F2523-I/SP

PIC18F2523-I/SP - 8-bit 32KB Flash MCU, 28-SPDIP | Microchip

The Microchip Technology PIC18F2523-I/SP is an 8-bit PIC18 RISC microcontroller featuring 32KB of Enhanced Flash program memory, 1536 bytes of RAM, and 256 bytes of EEPROM, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It operates from 2.0V to 5.5V, delivers up to 10 MIPS at 40 MHz, and integrates a 10-channel 12-bit ADC with nanoWatt power management, plus a 25 I/O count. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and peripherals such as ADCs, timers, and communication interfaces. The PIC18 family sits in Microchip's 8-bit PIC hierarchy: PIC18 -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. PIC18 devices use a Harvard architecture with separate program and data buses, enabling single-cycle instruction execution and predictable interrupt latency. Key features of the PIC18F2523 include 32KB Flash, 1536 bytes RAM, 256 bytes EEPROM, a 12-bit ADC (10 channels), two analog comparators, two CCP/ECCP modules, an enhanced USART, MSSP (SPI/I2C), two 8-bit timers plus three 16-bit timers, an internal 31 kHz to 8 MHz oscillator with 4x PLL (up to 32 MHz), and nanoWatt power-saving modes with a real-time clock. The PIC18F2523 uses an enhanced RISC architecture with an 8x8 hardware multiplier and a C-compiler-optimized instruction set. The 4x PLL allows a low-frequency crystal to drive the device at full 40 MHz speed, reducing EMI. Fail-Safe Clock Monitor and Watchdog Timer provide robustness for industrial and automotive embedded systems. Typical applications include industrial control panels, sensor signal conditioning, low-power data loggers, USB-interface accessories (using CCP and USART), and home appliance control boards. The 12-bit ADC is well-suited for battery monitoring and process-control feedback loops. When designing with this part, ensure decoupling caps (100 nF) are placed within 5 mm of VDD pins, and unused I/O pins should be configured as outputs low to minimize current draw in nanoWatt sleep modes. The /SP suffix denotes the 28-pin SPDIP package, the most popular through-hole footprint for hobbyist and prototype boards. This page synthesizes distributor pricing, drop-in alternatives sourced from Microchip's pin compatibility charts, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact