Products (21,000+)

PIC24F16KL402-I/ML - 16KB Flash 16-bit MCU XLP 28-QFN | Microchip
PIC24F16KL402-I/ML

PIC24F16KL402-I/ML - 16KB Flash 16-bit MCU XLP 28-QFN | Microchip

The Microchip Technology PIC24F16KL402-I/ML is a cost-effective 16-bit PIC24F microcontroller with nanoWatt XLP eXtreme Low Power technology, delivering 16 MIPS performance at 32 MHz core clock in a 28-pin QFN (6x6 mm) package. It integrates 16 KB of Flash program memory, 1 KB of SRAM data memory, and 512 bytes of data EEPROM, with on-chip peripherals carried over from the PIC18 family such as MSSP (I2C/SPI) and CCP/ECCP for design flexibility and easy upward migration. A 16-bit microcontroller (MCU) is an embedded processor that executes instructions on a 16-bit-wide data path, striking a balance between 8-bit devices (low cost, simple peripherals) and 32-bit devices (high performance, complex ecosystems). Within the broader taxonomy, the PIC24F16KL402 sits in the microcontroller -> embedded processor -> integrated circuit -> semiconductor chain, and within Microchip's portfolio it belongs to the PIC24F16KL40x family of XLP (eXtreme Low Power) MCUs optimized for battery-powered and energy-harvesting designs. Key features include a wide operating voltage range of 1.8V to 3.6V, 17 general-purpose I/O pins, a 10-bit ADC with up to 12 channels, four 16-bit timers, and ultra-low-power sleep modes that draw as little as 30 nA in Deep Sleep. The 28-QFN package offers a compact 6x6 mm footprint and a thermal pad for improved heat dissipation, suitable for space-constrained PCB designs. The nanoWatt XLP architecture integrates multiple power-saving modes (Doze, Idle, Sleep, Deep Sleep) and a hardware Real-Time Clock/Calendar for unattended operation. The PIC24F16KL402 uses a modified Harvard 16-bit core with single-cycle hardware multiply and divide, eliminating the bottleneck of software emulation common in 8-bit cores. Its peripheral set includes Capture/Compare/PWM (CCP/ECCP), Master Synchronous Serial Port (MSSP) configurable for SPI or I2C, UART, a 10-bit ADC, and comparators. The architecture supports in-circuit serial programming (ICSP) and in-circuit debugging via two debug pins. Typical applications include battery-powered sensor nodes, wearable health monitors, low-cost consumer electronics, IoT edge devices, and cost-sensitive industrial controls. The combination of 16-bit throughput, generous memory, and nanoWatt XLP power efficiency makes it well-suited for designs migrating from PIC18F where more MIPS or RAM are required without abandoning the familiar peripheral set. When designing with this device, ensure decoupling capacitors are placed close to VDD/VSS pairs and that the ICSP/ICD pins are routed to a programming header for in-circuit debug access during prototyping.

RFQ Contact
PIC24F16KL402-I/MQ - 16-Bit 32MHz XLP MCU | Microchip
PIC24F16KL402-I/MQ

PIC24F16KL402-I/MQ - 16-Bit 32MHz XLP MCU | Microchip

The Microchip Technology PIC24F16KL402-I/MQ is a cost-effective 16-bit PIC24F microcontroller with a 32 MHz operating frequency, 16 KB of Flash program memory, 1 KB of RAM, and a 28-QFN 5x5 mm package. It combines nanoWatt XLP low-power technology with MSSP I2C/SPI and CCP/ECCP peripherals for cost-sensitive embedded-control designs. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, input/output ports, and dedicated peripherals into one compact package. The PIC24F family occupies the low-cost embedded-control segment of the broader microcontroller hierarchy, combining a 16-bit RISC architecture with features familiar to users of PIC18 peripherals. This combination supports migration of cost-sensitive systems that require greater computational capability than an 8-bit platform. Key features include 16 KB of Flash memory organized as 5.5K x 24 words, 1 KB of SRAM, an additional 512-byte memory resource identified by distributor listings, and a 10-bit ADC. The device operates from a 1.8 V to 3.6 V supply range, supports up to 16 MIPS at 3.3 V, and includes Basic code-guard security. Its nanoWatt XLP feature set targets applications where low power consumption is as important as processing performance. The PIC24F16KL402 architecture is designed for economical, low-pin-count systems that need more control capability than an 8-bit MCU. Its MSSP peripheral supports I2C or SPI communication, while the CCP/ECCP blocks provide capture, compare, and PWM functions useful in motor, lighting, and signal-generation designs. The 28-QFN 5x5 mm package supports compact layouts, although exposed-pad layout and thermal verification must be considered during PCB design. Typical applications include portable consumer devices, portable GPS equipment, cell-phone accessories, electronic toys, portable sports products, disposable medical testers, dispensers, inhalers, and safety or security systems. The family data sheet specifically identifies these low-power, low-cost application areas, while the MSSP and CCP/ECCP peripherals support connected sensors, actuator control, and communication interfaces. When designing around the PIC24F16KL402-I/MQ, verify the 28-QFN land pattern, exposed-pad requirements, and decoupling layout against the manufacturer data sheet. If low-power operation is required, configure the nanoWart XLP modes carefully and validate every peripheral state. The 3.3 V operating point supports 16 MIPS, while operation across the full 1.8 V to 3.6 V range may require the device to operate at a lower frequency. This product record combines verified manufacturer and distributor specifications with practical low-power design guidance, package considerations, and explicit data gaps. It distinguishes documented parameters from values that must be checked in the complete family data sheet, helping engineers make sourcing and design decisions without treating unverified assumptions as specifications.

RFQ Contact
PIC24F16KL402-I/SO - 16-bit XLP MCU 32MHz 16KB Flash 28-SOIC | Microchip
PIC24F16KL402-I/SO

PIC24F16KL402-I/SO - 16-bit XLP MCU 32MHz 16KB Flash 28-SOIC | Microchip

The Microchip PIC24F16KL402-I/SO is a 16-bit PIC24F microcontroller featuring nanoWatt XLP eXtreme Low Power technology, 16KB Flash program memory, 32 MHz CPU clock, and a 28-pin SOIC package. It is part of the cost-effective PIC24F "KL" family aimed at applications requiring low-power consumption with more computational ability than an 8-bit platform provides. A 16-bit microcontroller (MCU) is a programmable computing engine with a 16-bit data path, instruction set, internal buses, and registers. Within the broader MCU hierarchy, the PIC24F16KL402 belongs to the 16-bit MCU category, sitting above 8-bit MCUs (e.g., PIC16) in performance and below 32-bit Cortex-M/MIPS cores in computational throughput. It uses a modified Harvard layout, persistent SRAM, and a RISC-style instruction set with hardware MAC support for DSP-like operations. Key features include 16KB Flash (5.5K x 24 instruction words), 1KB RAM, a 10-bit ADC, dual I2C/SPI (MSSP) peripherals, CCP/ECCP, multiple timers, and 25 I/O pins on the 28-SOIC variant. Typical run-mode current is 150 uA/MHz at 1.8V, with deep Sleep currents in the nanoamp range thanks to nanoWatt XLP technology. The PIC24F16KL402 architecture integrates a wide operating voltage range (1.8V-3.6V), internal oscillator options, a configurable RTCC, and a 16-bit-wide data path. Its hardware multiplier and DSP-friendly instructions enable efficient signal processing while keeping code size compact - the 16 KB Flash translates to roughly 5.5K single-word instructions. Typical applications include portable consumer devices (media players, electronic toys, cell phone accessories), low-cost medical disposables (testers, inhalers), safety/security peripherals, sensor signal conditioning, and battery-powered IoT nodes where every nanosecond down matters. When using this part, match the 28-SOIC footprint carefully; the PIC24F "KL" family ships in 14/20/28-pin variants with different pinouts. Verify peripheral mapping and voltage rails against your design, and use MPLAB X IDE with the XC16 compiler to leverage the DSP library and XLP-aware PMD bits. This page synthesizes distributor pricing, drop-in package alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Contact
PIC24F16KL402-I/SP - 16-Bit 32MHz 16KB MCU | Microchip
PIC24F16KL402-I/SP

PIC24F16KL402-I/SP - 16-Bit 32MHz 16KB MCU | Microchip

The Microchip Technology PIC24F16KL402-I/SP is a cost-sensitive 16-bit PIC microcontroller featuring nanoWatt XLP technology for eXtreme Low Power consumption. It operates at up to 32 MHz, provides 16 KB of Flash memory and 1 KB of SRAM, and is packaged in a 28-pin SPDIP. The MCU combines computational capability beyond an 8-bit platform with power-management features for embedded, portable, and cost-constrained products. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and I/O into one package. The PIC24F16KL402 belongs to the 16-bit PIC24F family and uses a PIC RISC architecture. Its MSSP peripheral supports I2C and SPI communication, while its CCP/ECCP blocks provide flexible capture, compare, and PWM functions. These features make the device useful in portable media players, accessories, low-cost testers, dispensers, inhalers, security products, and other low-power embedded systems. The verified product listing identifies 16 KB of Flash organized as 5.5K x 24 words, 1 KB of RAM, a 10-bit ADC, a 3 V supply description, and a maximum clock speed of 32 MHz. The -I/SP suffix denotes an industrial-temperature, through-hole SPDIP ordering configuration according to the distributor listings. The family documentation describes the part as a 28-pin, low-power device, while the product data identifies nanoWatt XLP functionality and PIC18-family peripherals such as MSSP and CCP/ECCP. The MCU is positioned for systems requiring more processing capability than an 8-bit controller without adopting a higher-cost architecture. Its low-power feature set is particularly relevant for battery-operated and portable equipment, where average current consumption can affect battery life and user experience. The family documentation specifically identifies consumer, medical, and safety/security applications, including portable media players, portable GPS, cell-phone accessories, electronic toys and games, portable sports gear, disposable medical testers, dispensers, inhalers, and security equipment. Designers should choose this MCU when they need a low-pin-count, through-hole package and a cost-effective 16-bit control platform. They should verify the exact pin assignments, peripheral multiplexing, clock configuration, ADC channels, and electrical limits from the Microchip family data sheet before layout or firmware development. For new production, procurement teams should also confirm current pricing and inventory directly with an authorized distributor. This product page combines the verified Microchip product information, distributor specifications, pricing references, and practical selection context. It also distinguishes true same-package drop-in alternatives from functional replacements that may require PCB changes. The information is intended to support engineering comparison, sourcing, and design-in decisions rather than replace the manufacturer’s complete technical documentation.

RFQ Contact
PIC24F16KL402-I/SS - 16-bit XLP MCU, 32MHz, 16KB Flash | Microchip
PIC24F16KL402-I/SS

PIC24F16KL402-I/SS - 16-bit XLP MCU, 32MHz, 16KB Flash | Microchip

The Microchip Technology PIC24F16KL402-I/SS is a 16-bit PIC24F microcontroller built on the nanoWatt XLP eXtreme Low Power architecture, delivering up to 32 MHz (16 MIPS) performance from a 3.3 V supply in a 28-pin SSOP package. It integrates 16 KB of Flash program memory (5.5K x 24 words), 1 KB of SRAM, and a feature set tailored for cost-sensitive, low-power applications that need more computational headroom than 8-bit MCUs can provide. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, peripherals, and I/O. The 16-bit PIC24F family sits between 8-bit PIC18 devices and 32-bit PIC32 parts in Microchip's portfolio, offering a balance of low cost, low power, and higher code density for C-based firmware. The 'KL' sub-series is the low-pin-count, low-power branch aimed at consumer, medical, and portable safety/security products. Key features include a 10-bit, up to 12-channel A/D converter with 500 ksps conversion rate and Sleep/Idle-mode sampling, dual rail-to-rail analog comparators with programmable I/O, an on-chip voltage reference, three 16-bit timers, a 16-bit Capture/Compare/PWM (ECCP) module, an MSSP peripheral supporting both I2C and SPI, and up to 25 general-purpose I/O pins. The nanoWatt XLP technology enables currents below 1.8 µA in Sleep mode with RTCC and 30 nA in deep Sleep. According to the Microchip PIC24F16KL402 Family Data Sheet, the device supports ICD (In-Circuit Debug) via dedicated PG/RE pins and operates across -40 °C to +85 °C industrial temperature range. Typical applications include low-cost medical disposables (testers, dispensers, inhalers), portable consumer electronics (media players, GPS accessories, cell phone peripherals, electronic toys and games), safety/security sensors, battery-powered sensor nodes, and home appliances. The wide peripheral mix allows designers to migrate existing PIC18 firmware while gaining 16-bit performance. When designing with this part, plan for a 3.3 V core supply, place 0.1 µF decoupling near each VDD pin, and connect the exposed pad (where present) to the ground plane for thermal relief. The MSSP can be configured for either I2C or SPI but not both simultaneously; firmware must select one mode at runtime.

RFQ Contact
PIC24F16KL402T-I/ML - 32MHz 16-bit XLP MCU | Microchip
PIC24F16KL402T-I/ML

PIC24F16KL402T-I/ML - 32MHz 16-bit XLP MCU | Microchip

The Microchip PIC24F16KL402T-I/ML is a 32 MHz, 16-bit PIC24F microcontroller with 16 KB of Flash program memory, 1 KB of SRAM, and a 10-bit ADC, housed in a 28-QFN 6x6 mm package. It combines compact 16-bit processing with nanoWatt XLP technology for low-power embedded designs. The device supports a 1.8 V to 3.6 V operating range and provides 17 I/O ports according to the manufacturer documentation. A 16-bit microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals in one integrated circuit. The PIC24F16KL402 belongs to the PIC24F family and positions itself between an 8-bit controller and a more complex general-purpose MCU. Its architecture is intended for cost-sensitive systems requiring stronger computational performance and communication peripherals without the cost and complexity of a larger microcontroller. The principal resources are 16 KB of Flash, 1 KB of SRAM, and 512 bytes of EEPROM, while the 10-bit ADC supports analog measurements required in control and sensing systems. Operation up to 32 MHz provides up to 16 MIPS performance. Integrated MSSP resources support I2C and SPI communication, and CCP/ECCP peripherals add capture, compare, and PWM capabilities for timing-sensitive applications. The -I grade identifies the industrial temperature option, supporting operation from -40°C to +125°C. The T-I/ML ordering code selects the industrial-grade device in the 28-QFN 6x6 mm package. Lead-free construction is identified for this ordering code, making it appropriate for current RoHS-oriented manufacturing processes when the applicable product declarations and assembly requirements are confirmed for the production lot. Typical uses include industrial sensor nodes, compact control panels, battery-operated instruments, serial data acquisition modules, and low-cost communications equipment. The MSSP peripherals are particularly useful when a design must connect an ADC, display, external memory, or sensor over I2C or SPI. The CCP/ECCP blocks are valuable for motor-control timing, signal capture, and PWM generation without relying on software timing loops. When laying out the circuit, place input, output, and decoupling connections directly beneath the associated QFN terminals and follow the manufacturer land-pattern requirements. Keep sensitive analog inputs away from high-current switching paths, provide a stable supply reference, and validate the complete pin assignment against the datasheet before routing a replacement board. This product overview combines the key electrical limits, package details, application guidance, cross-reference constraints, and practical design considerations engineers need when evaluating the PIC24F16KL402T-I/ML for a new low-power embedded platform.

RFQ Contact
PIC24F16KM102-E/ML - 16KB 32MHz XLP 16-bit MCU | Microchip
PIC24F16KM102-E/ML

PIC24F16KM102-E/ML - 16KB 32MHz XLP 16-bit MCU | Microchip

The Microchip PIC24F16KM102-E/ML is a 16-bit PIC24F microcontroller from the nanoWatt XLP eXtreme low-power family, delivering 32 MHz performance with 16 KB Flash, 1 KB RAM and 512 B EEPROM. Housed in a 28-pin QFN (6x6 mm) package, this MCU is optimized for low-cost, low-pin-count applications that demand ultra-low power consumption. A PIC microcontroller (MCU) is a compact programmable processor integrating CPU, Flash, RAM, EEPROM, and digital/analog peripherals on a single silicon die. It belongs to the broader hierarchy: microcontroller -> embedded processor -> semiconductor device. The 16-bit PIC24F family sits above 8-bit PIC16 devices and below 32-bit PIC32 devices, balancing code efficiency, deterministic interrupt latency, and ease of programming with the MPLAB X IDE and XC16 compiler toolchain. Key differentiating features of the PIC24F16KM102-E/ML include nanoWatt XLP sleep currents below 1 uA, flexible Capture/Compare/PWM (MCCP/SCCP) modules for motor or timing control, a Configurable Logic Cell (CLC) for hardware glue logic, an integrated 12-bit ADC with multiple comparators, and 5V-tolerant I/O supporting both 3 V and 5 V application rails. The 32 MHz core executes 16 MIPS, enabling responsive control algorithms in real-time embedded loops. Architecturally, the device combines a modified Harvard core with DSP-friendly instructions, 17-bit wide instruction paths, and a 16-bit data path. The result is efficient interrupt response and predictable deterministic timing suitable for digital power conversion, motor control, and sensor signal conditioning. The peripheral set is event-triggable and supports DMA-style peripheral mapping for low-CPU-load operation. Typical uses include microcontrollers that drive portable medical devices, IoT edge sensors, low-power wireless sensor nodes, consumer appliances, and industrial control boards where battery life, deterministic performance, and small PCB footprint are essential. The extended -40C to +125C operating range supports harsh-environment deployment. When designing with this device, ensure MPLAB X IDE and the latest XC16 compiler are installed, since peripheral libraries are version-sensitive. Place a 1 uF plus 100 nF decoupling pair adjacent to every VDD/VSS pin pair, and route the ICSP programming signals (PGECx/PGEDx) to a debug header. Verify that the QFN thermal pad is soldered to a sufficient copper pour for reliable thermal dissipation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC24F16KM102-E/SO - 16KB Flash 16-bit MCU 28-SOIC | Microchip
PIC24F16KM102-E/SO

PIC24F16KM102-E/SO - 16KB Flash 16-bit MCU 28-SOIC | Microchip

The Microchip Technology PIC24F16KM102-E/SO is a 16-bit microcontroller from the PIC24F XLP family featuring 16KB (5.5K x 24) of Flash program memory, 1KB of RAM and 512 bytes of EEPROM, housed in a 28-pin SOIC (7.50 mm body width) package. The device integrates a 16-bit PIC core capable of 32 MHz operation (8 MIPS), supports both 3V and 5V application rails, and consumes nanoWatt Xtreme low power for battery-friendly designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), EEPROM for data retention, and a rich set of peripherals including ADC, timers, communication interfaces and GPIOs. MCUs sit at the lowest tier of the embedded-computing hierarchy above discrete logic and below microprocessors/M SoCs, and are the foundational building block for nearly every embedded product from sensor nodes to industrial controllers. The PIC24F family specifically targets low-power, mixed-signal applications where XLP (eXtreme Low Power) sleep currents in the nanoampere range are required. Key features include a 12-bit A/D converter with multiple input channels, multiple Capture/Compare/PWM (MCCP/SCCP) modules for motor or power control, analog comparators, configurable logic cells (CLC), and a wide operating temperature window. The XLP nanoWatt technology delivers sleep currents below typical competing MCUs and supports multiple low-power modes such as Sleep, Idle and Doze. The architecture pairs a 16-bit modified-Harvard CPU with a hardware multiplier and a 32 kHz to 32 MHz internal oscillator block, simplifying BOM by removing external crystals in cost-sensitive designs. The on-chip 12-bit ADC, op-amps, comparators and CLC blocks allow analog front-ends to be built with very few external components, while the MCCP/SCCP peripherals support PWMs for motor, lighting and SMPS control loops. Typical applications include industrial sensor nodes, low-power IoT edge devices, portable medical accessories, consumer white goods with motor control, capacitive-touch human-interface panels, and battery-powered metering. The wide 1.8V to 3.6V VDD range (with PIC24FV variants at 2.0V to 5.5V) supports single-cell Li-ion or 2x AA chemistries directly. The 28-SOIC package is friendly to hand-soldering and low-cost 2-layer PCBs. When designing with this device, plan the GPIO/peripheral mapping early, because the limited 28-pin count forces trade-offs between analog channels, PWM outputs and comms interfaces. Also ensure the configuration bits are programmed correctly to enable the internal oscillator and disable unused peripherals for lowest sleep current. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC24F family, and practical design notes not collected together in the manufacturer datasheet.

RFQ Contact
PIC24F16KM102-E/SP - 16-Bit 32MHz XLP MCU | Microchip
PIC24F16KM102-E/SP

PIC24F16KM102-E/SP - 16-Bit 32MHz XLP MCU | Microchip

The Microchip Technology PIC24F16KM102-E/SP is a 16-bit PIC24F XLP microcontroller operating at up to 32 MHz, with 16 KB of Flash program memory, 1 KB of SRAM, and a 28-pin SPDIP package. It is designed for cost-sensitive embedded applications that require a compact instruction set, flexible digital peripherals, low-power operation, and operation across 3 V and 5 V systems. The -E/SP ordering identifies the extended-temperature, 28-pin through-hole configuration. A microcontroller is a semiconductor device that integrates a processor core, nonvolatile program memory, data memory, input/output ports, timers, communication peripherals, and control logic on one integrated circuit. The PIC24F16KM102 belongs to the PIC24F family and uses the PIC24 architecture, which provides a 16-bit instruction set and Harvard-style program and data memory organization. Its compact 28-pin package simplifies prototyping and human-readable breadboard or through-hole assembly. The device provides 16 KB of Flash memory organized as 5.5K words by 24 bits and 1 KB of SRAM for working data. Its maximum operating frequency is 32 MHz. Flexible capture, compare, and PWM modules support timing, motor-control, and signal-generation tasks, while the configurable logic cell provides additional programmable digital functions. These resources make the PIC24F16KM102 suitable for local control, measurement, communications, and mixed-signal interface systems. The PIC24F family is positioned for low-power embedded designs, with nanoWatt XLP technology forming part of the family’s low-power feature set. Low-power behavior is especially useful in battery-powered equipment, portable instruments, environmental monitors, and products that spend significant time in sleep or idle states. Developers can use the on-chip clock, timers, interrupt system, and power-management features to reduce activity when external inputs do not require continuous processing. Typical uses include compact environmental sensors, industrial control modules, appliance controllers, LED drivers, communication interfaces, and low-cost embedded instruments. The 28-pin SPDIP format is particularly helpful when a product is assembled through wave soldering, automated through-hole insertion, or manual prototyping. Firmware can be organized around the PIC24F peripheral architecture while using the 16 KB Flash region for application code and configuration data. Designers should verify the exact operating voltage, clock configuration, peripheral availability, and decoupling requirements against the manufacturer datasheet before layout release. A 100 nF decoupling capacitor should be placed close to each supply connection, and programming and configuration pins must be routed for ISP or equivalent programming access. The 32 MHz maximum clock speed also requires disciplined clock, layout, and signal-integrity decisions when operated near the upper frequency limit. This product page combines the exact device identity, package details, technical specifications, design guidance, qualification considerations, and same-footprint alternatives needed to plan an embedded-control design. It also distinguishes the extended-temperature -E grade from the industrial -I grade and clarifies where temperature or qualification requirements determine the correct device ordering code.

RFQ Contact
PIC24F16KM102-E/SS - 16-Bit 32MHz MCU | Microchip Technology
PIC24F16KM102-E/SS

PIC24F16KM102-E/SS - 16-Bit 32MHz MCU | Microchip Technology

The Microchip Technology PIC24F16KM102-E/SS is a PIC XLP 24F 16-bit microcontroller operating at up to 32 MHz, with 16 KB of Flash program memory, 1 KB of RAM, and 512 bytes of EEPROM in a 28-pin SSOP package. It combines a low-power MCU architecture with integrated analog and communications peripherals for compact control designs. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, data memory, and peripherals such as timers, serial interfaces, and analog converters on one device. The PIC24F16KM102 belongs to the PIC24F family of 16-bit microcontrollers, the PIC XLP low-power product family, and the broader embedded-control semiconductor category. This integration reduces component count and allows firmware to control measurement, communication, and actuator functions in a single compact circuit. Key features include a 16-bit PIC core, operation up to 32 MHz, 16 KB of Flash organized as 5.5K x 24 bits, 1 KB x 8 RAM, and 512 x 8 EEPROM. The device also provides a 12-bit ADC, comparator, MCCP/SCCP peripherals, configurable logic cells, and communication interfaces including I2C, SPI, UART/USART, IrDA, and LINbus. These resources support both periodic control and low-rate serial networking. The PIC XLP architecture emphasizes low-power operation, while the flexible capture/compare/PWM modules support timing, motor-control, and signal-generation functions. The 12-bit ADC enables analog sensor acquisition without adding a separate converter. Data can be retained in EEPROM for calibration values or configuration parameters, although firmware should observe the device's endurance and write-cycle limits when using it for frequently changing information. Typical applications include compact industrial controllers, low-power sensor nodes, building-control modules, appliance controllers, motor-control peripherals, and LIN-connected automotive or transportation equipment. The 28-pin SSOP package is useful when a design needs more I/O than a small microcontroller package can provide while remaining compatible with conventional surface-mount assembly. Designers should confirm the exact pin assignments, peripheral multiplexing, voltage limits, decoupling requirements, and programming configuration in the manufacturer datasheet before layout is released. Place the required bypass capacitors close to the supply pins, provide clean analog grounding for ADC measurements, and route high-current switching outputs away from sensitive analog inputs to minimize coupling and measurement errors. This product page combines the manufacturer specifications, package information, practical application guidance, and drop-in replacement analysis. It also provides engineering-focused comparison notes that help identify differences in memory, core speed, peripheral availability, and qualification requirements before a PCB or firmware migration is attempted.

RFQ Contact
PIC24F16KM102-I/ML - 16-Bit 32MHz MCU | Microchip Technology
PIC24F16KM102-I/ML

PIC24F16KM102-I/ML - 16-Bit 32MHz MCU | Microchip Technology

The Microchip Technology PIC24F16KM102-I/ML is a 16-bit PIC24F microcontroller with a 32 MHz operating frequency, 16 KB of Flash program memory, and a 28-QFN package measuring 6 mm by 6 mm. It is designed around Microchip's nanoWatt eXtreme low-power technology and provides configurable analog and digital peripherals for compact embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals on one device. The PIC24F family belongs to the broader embedded-controller hierarchy, combining general-purpose processing with timers, communication interfaces, analog conversion, and low-power control. This makes the PIC24F16KM102-I/ML suitable for applications in which local sensing, control, and communication must coexist on a small circuit board. The device offers 16 KB of Flash memory, equivalent to 5.5K by 24 bits, and operates at 32 MHz. Its integrated features include a 12-bit ADC, comparators, flexible Capture/Compare/PWM modules, and Configurable Logic Cells. The family supports both 3 V and 5 V applications, while the PIC24FV naming used in one distributor listing identifies a related family variant with a 2.0 V to 5.5 V operating range. Confirm the exact electrical limits for the ordered MPN in the manufacturer documentation. PIC24F16KM102-I/ML belongs to the low-pin-count PIC24F XLP portfolio, where XLP denotes nanoWart eXtreme low-power operation. Its architecture is intended to balance responsive processing with reduced energy consumption in battery-operated and intermittently powered equipment. Multiple programming and programming-verification pin pairs are available according to the device-specific programming information, so firmware tooling and PCB access must be planned before fabrication. Typical uses include battery-powered environmental sensors, compact industrial monitoring equipment, consumer controls, LED lighting interfaces, and low-power embedded instruments. The 12-bit ADC supports analog measurement, the comparators support threshold detection, and the PWM peripherals can drive indicators or actuator controls. The small 6 mm by 6 mm QFN format also supports space-constrained products with dense mixed-signal layouts. Design the decoupling network close to the supply pins and reserve adequate exposed-pad copper for thermal dissipation. Confirm programming connector access, pin multiplexing, analog reference requirements, and the exact voltage range for the selected ordering code before release. Treat the 28-QFN land pattern as unsuitable for direct assembly without a qualified PCB footprint and a deliberate package-orientation plan. This product page combines the manufacturer's family-level characteristics with distributor-confirmed order information, a same-package comparison, and engineering guidance for low-power PCB design. It also distinguishes the target ordering code from package variants and similar family members that are not automatically drop-in replacements.

RFQ Contact
PIC24F16KM102-I/SO - 16-bit 32MHz XLP MCU 16KB Flash | Microchip
PIC24F16KM102-I/SO

PIC24F16KM102-I/SO - 16-bit 32MHz XLP MCU 16KB Flash | Microchip

The Microchip Technology PIC24F16KM102-I/SO is a 16-bit PIC® XLP™ (eXtreme Low Power) microcontroller featuring a 32 MHz MIPS CPU core, 16 KB of Flash program memory, 1 KB of SRAM, and 512 bytes of EEPROM, housed in a 28-pin SOIC (SO) wide-body package. It integrates a 12-bit A/D converter with up to 19 channels, multiple Capture/Compare/PWM (MCCP/SCCP) timers, comparators, and a Configurable Logic Cell (CLC) for hardware peripheral customization. The KM family is positioned as a low-pin-count, low-cost extension of the PIC24F lineup targeting battery-powered and space-constrained designs. A 16-bit PIC microcontroller is a member of the broader microcontroller (MCU) family, which sits within embedded computing and semiconductor hierarchies. PIC24F devices use a modified Harvard RISC architecture with 16-bit instructions and 24-bit address space, balancing 8-bit MCU simplicity with 32-bit-class performance at low power. They belong to Microchip's nanoWatt XLP™ product tier, where extreme low-power operation is the primary design driver rather than raw performance. Key features include a wide operating voltage range of 1.8 V to 5.5 V for the PIC24F variant, deep sleep modes with nanoWatt current consumption, multiple serial interfaces (UART, SPI, I2C), and rich analog peripherals for sensor interfacing. The CLC peripheral allows glue-logic implementation in hardware, reducing firmware overhead and CPU wakeups. Compared to the older PIC24F16KA family, the KM devices add configurable logic and improved ADC performance while retaining the same compiler and MPLAB X toolchain compatibility. The architecture combines a single-cycle 16-bit datapath with DSP-oriented instructions and hardware multiply/divide, enabling efficient signal processing at clock rates up to 32 MHz (8 MIPS). The 12-bit ADC supports up to 200 ksps, suitable for sensor acquisition loops in IoT nodes. The combination of CLC, comparators, and PWM allows closed-loop motor control, lighting control, and power conversion feedback without external logic. Typical applications include low-power IoT sensor nodes, consumer electronics remote controls, battery-powered medical devices, and industrial sensor interfaces. The wide 1.8 V to 5.5 V supply range and integrated analog simplify designs powered directly from single-cell Li-ion, two AA cells, or regulated 3.3 V rails. The device is also commonly used in touch-sense front ends, low-cost motor control boards, and HVAC peripherals. When designing with the PIC24F16KM102-I/SO, ensure that the wide-body 28-SOIC footprint (7.50 mm body width) is correctly placed in PCB libraries - the SO package is mechanically larger than the SSOP variant in the same family. Also note that firmware is portable across KM and KA flash families, but pin assignments for the CLC and comparator outputs differ between SO and SS/SP/QFN variants. This page synthesizes distributor pricing across 9 channels, validated drop-in alternatives within the same SOIC-28 footprint, and practical design notes not found in the standalone datasheet.

RFQ Contact
PIC24F16KM102-I/SP - 16KB Flash 32MHz 16-bit XLP MCU | Microchip
PIC24F16KM102-I/SP

PIC24F16KM102-I/SP - 16KB Flash 32MHz 16-bit XLP MCU | Microchip

The Microchip Technology PIC24F16KM102-I/SP is a 16-bit PIC24F microcontroller featuring 16KB (5.5K x 24 words) of Flash program memory, 2KB of SRAM and 512B of EEPROM, executing up to 32 MHz (16 MIPS) from a 1.8V to 5.5V supply in a 28-pin SPDIP (0.300 inch, 7.62mm) through-hole package. It is part of the nanoWatt XLP (eXtreme Low Power) PIC24F family with on-chip Configurable Logic Cells (CLC), Capture/Compare/PWM, a 12-bit ADC and UART/SPI/I2C peripherals aimed at cost-sensitive 3V and 5V embedded designs. What is a PIC24F microcontroller? PIC24F is Microchip's 16-bit Modified-Harvard MCU architecture - the mid-range step between the 8-bit PIC16/PIC18 and the 32-bit PIC32. PIC24F devices use a 24-bit instruction word with 16-bit data paths, offer far richer peripherals than PIC16/PIC18 while consuming less power and costing less than PIC32. The 'F' suffix indicates Flash program memory. PIC24F sits in the taxonomy: PIC24F -> 16-bit MCU -> microcontroller -> embedded IC -> semiconductor. Key features of the PIC24F16KM102-I/SP include nanoWatt XLP deep-sleep modes that drop current to the sub-microamp range, a 12-bit A/D converter with up to 9 channels, multiple 16-bit timers, a Real-Time Clock and Calendar (RTCC) module, and on-chip CLC that lets designers wire internal peripherals into custom combinational/sequential logic without external gates. The device supports 24 I/O pins across its 28-pin SPDIP body, giving ample headroom for sensor and user-interface integration. Architecturally, the PIC24F16KM102 pairs a modified-Harvard CPU with single-cycle 16-bit ALU operations, hardware Multiply and Divide, and an interrupt controller that supports both fixed and programmable priority levels. The wide 1.8V to 5.5V operating range means the same part can power directly from a single Li-ion cell, two alkaline cells, a 3.3V LDO output, or a regulated 5V rail - eliminating a level-shifter stage in mixed-voltage designs. Typical applications include battery-powered IoT sensor nodes, consumer appliances, low-cost motor and lighting controllers, USB-CDC serial bridges, and industrial control modules. In each, the XLP sleep currents below 1 uA extend battery life, while the CLC and PWM simplify BOM by removing discrete gates and timer ICs. Design consideration: when migrating from PIC24F16KA102 designs, verify peripheral remapping and CLC pin assignments - although both are XLP PIC24F parts, the KM family expands logic-cell and PWM resources. This page synthesizes distributor pricing, drop-in alternatives and design notes not found in the standalone Microchip datasheet.

RFQ Contact
PIC24F16KM102-I/SS - 16KB Flash 16-bit MCU | Microchip | SSOP-28
PIC24F16KM102-I/SS

PIC24F16KM102-I/SS - 16KB Flash 16-bit MCU | Microchip | SSOP-28

The Microchip PIC24F16KM102-I/SS is a 16-bit PIC24F microcontroller delivering 16 KB of Flash program memory, 1 KB of RAM and 512 bytes of EEPROM in a 28-pin SSOP package. It operates at up to 32 MHz core clock with an integrated 16-bit MIPS-modified Harvard architecture and supports a wide 1.8 V to 5.5 V supply range that covers both 3.3 V and 5 V application rails. The MCU integrates a 12-bit A/D converter, multiple Capture/Compare/PWM modules, configurable logic cells (CLC), and serial peripherals including I2C, SPI, UART and IrDA/LIN. A 16-bit microcontroller (MCU) is a single-chip computer with a 16-bit datapath, program counter and ALU, positioned between 8-bit MCUs and 32-bit MCUs in the embedded hierarchy: 16-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC24F family belongs to the nanoWatt XLP eXtreme Low Power family and is widely used in cost-sensitive, low-pin-count, battery-powered designs that need higher arithmetic performance than 8-bit parts without the cost of a 32-bit ARM core. Key features include 24 general-purpose I/O pins, brown-out reset, low-voltage detect, power-on reset, watchdog timer, PWM output, and a peripheral pin select (PPS) mapping engine. The on-chip Configurable Logic Cell lets designers implement glue-logic, waveform synthesis or simple state machines in hardware without external gates, reducing BOM cost and PCB area. The device uses a modified Harvard architecture with separate program Flash and data EEPROM/RAM buses, allowing concurrent instruction fetch and data access for deterministic 32 MHz performance. PPS routing of digital peripherals to physical pins gives layout flexibility, while the 12-bit ADC can be paired with the CLC for sensor-edge processing. Typical applications include consumer white goods, low-cost sensor nodes, building automation, portable instrumentation, and USB/HID-free human-interface boards. The wide operating voltage also makes it suitable for industrial 24 V-bus-derived rails after pre-regulation. Compared to PIC24F16KA102-I/SS, this KM102 variant adds configurable logic cells and more flexible timer options, while sharing the same Flash and RAM density for direct migration. When designing with this part, allocate decoupling of 100 nF plus 10 uF bulk close to VDD/VSS, keep ADC traces short, and use the PPS feature to remap peripherals instead of re-spinning the PCB. The CLC module must be configured before peripheral disable to avoid transient logic glitches. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving procurement and firmware teams a single reference for evaluating the PIC24F16KM102-I/SS against modern 32-bit alternatives.

RFQ Contact
PIC24F16KM102T-I/SO - 16-bit XLP 32MHz MCU, 16KB Flash | Microchip
PIC24F16KM102T-I/SO

PIC24F16KM102T-I/SO - 16-bit XLP 32MHz MCU, 16KB Flash | Microchip

The Microchip Technology PIC24F16KM102T-I/SO is a 16-bit PIC® XLP™ (eXtreme Low Power) microcontroller running at 32 MHz with 16 KB Flash, 1 KB RAM and 512 bytes of EEPROM in a 28-pin SOIC wide-body package. It belongs to the PIC24F KM1 family of nanoWatt XLP microcontrollers, delivering 16 MIPS of throughput with a 5.5 V image per pin and supporting both 3 V and 5 V applications. The 'I' suffix denotes the industrial temperature range of -40 °C to +85 °C, while the 'T' indicates tape-and-reel packaging. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of on-chip peripherals such as timers, ADC, communication interfaces and configurable logic. The PIC24F family is built around Microchip's 16-bit modified Harvard architecture, sitting in the hierarchy between 8-bit PIC MCUs and the higher-end dsPIC/PIC 32 families. The XLP designation indicates aggressive nanoWatt sleep-current design, making KM1-series parts especially well-suited to battery-powered or energy-harvesting products. Key features of the PIC24F16KM102T-I/SO include 16 KB Flash (5.5 K × 24 instruction words), 1 KB RAM and 512 bytes of EEPROM, three 16-bit Capture/Compare/PWM (MCCP/SCCP) modules, a 12-bit A/D converter with up to 10 channels, analog comparators, a Configurable Logic Cell (CLC) for hardware glue logic, and a rich set of serial peripherals including I²C, SPI and UART. The wide 1.8 V to 5.5 V operating voltage range plus a low-power sleep current in the microamp range positions this part for portable, sensor and consumer devices. The architecture combines a 16-bit data path with an 8-channel DMA, dual 16-bit timers and a flexible pin-mapping Peripheral Pin Select (PPS) block. PPS allows digital peripherals to be remapped to a wide range of I/O pins at runtime, which simplifies PCB layout and BOM reuse inside the KM1 family. The 12-bit ADC supports up to 500 ksps with hardware accumulation, and the CLC block can implement state machines, waveform generation and signal conditioning in pure hardware. Typical applications include ultra-low-power sensor nodes, battery-powered IoT endpoints, portable medical accessories, consumer human-interface devices, low-cost motor control, and general-purpose embedded control with a 3 V coin-cell or USB-derived supply. The 28-pin SOIC package also enables hand-soldering and breadboarding for prototype and hobby use. Compared with smaller 14/20-pin KM1 devices, the 28-pin variants expose more ADC channels and PWM channels, so they fit designs where more analog or timing resources are required. When designing with this part, budget for an external decoupling network of 100 nF + 10 µF within 5 mm of every VDD/VSS pair, and use the PPS block to keep high-speed signals short. The KM1 family shares its MPLAB X IDE toolchain, MCC code configurator and XC16 compiler with other PIC24F devices, easing migration if a 28-pin part becomes capacity-constrained and you move up or down the family. This page synthesises verified distributor stock data, parametric drop-in alternatives inside the same PIC24F KM1 family, and design notes drawn from Microchip datasheet sections - information not always found on a single distributor product page.

RFQ Contact
PIC24F16KM104-E/ML - 32MHz 16-bit MCU | Microchip Technology
PIC24F16KM104-E/ML

PIC24F16KM104-E/ML - 32MHz 16-bit MCU | Microchip Technology

Microchip Technology PIC24F16KM104-E/ML is a 16-bit PIC XLP 24F microcontroller with a 32 MHz maximum operating frequency, 16 KB of Flash program memory, 1 KB of RAM, and 512 bytes of EEPROM in a 44-QFN 8 x 8 mm package. The device operates from 1.8 V to 5.5 V and combines a low-power microcontroller architecture with integrated analog resources. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, working data memory, timers, communication peripherals, and I/O ports on one device. PIC24F devices belong to the 16-bit MCU -> microcontroller -> embedded semiconductor hierarchy and use a Harvard-style architecture suited to compact control systems. The PIC XLP designation identifies this family’s focus on low-power operation and compact embedded designs. The PIC24F16KM104 integrates a 12-bit ADC, a DAC, and operational amplifiers according to the manufacturer product page. Its 5.5K x 24 Flash organization accommodates a 16-bit instruction architecture, while its 1 KB SRAM and 512-byte EEPROM support working state and nonvolatile parameter storage. The operating range of 1.8 V to 5.5 V allows the same device family to serve both 3 V and 5 V systems. Programmable peripherals include flexible Capture/Compare/PWM modules and a Configurable Logic Cell, as described for the PIC24F family. These resources allow the MCU to measure timing inputs, generate PWM waveforms, and implement small amounts of hardware-assisted logic without requiring additional discrete components. The 44-QFN package reduces board area but requires careful escape routing and attention to the exposed thermal pad. Typical uses include low-power sensor nodes, industrial condition-monitoring equipment, compact motor or actuator controllers, analog signal acquisition systems, and embedded products that need both digital control and on-chip ADC, DAC, or amplifier functions. The 16 KB Flash limit makes memory planning important when the application includes graphical interfaces, extensive protocol stacks, or large data buffers. Designers should reserve decoupling capacitance at each supply pin, route the exposed pad as a thermal and electrical landing area, and verify signal compatibility at the lowest and highest intended supply voltage. Firmware, peripheral assignments, and pin multiplexing must be checked against the manufacturer pin-description table and device documentation before PCB release. This product page consolidates the manufacturer specifications, lifecycle information, pin-compatible alternatives, application guidance, and practical design considerations needed to evaluate the PIC24F16KM104-E/ML for an embedded control design.

RFQ Contact
PIC24F16KM104-E/MV - 32MHz 16-Bit Low-Power MCU | Microchip
PIC24F16KM104-E/MV

PIC24F16KM104-E/MV - 32MHz 16-Bit Low-Power MCU | Microchip

The Microchip Technology PIC24F16KM104-E/MV is a 16-bit PIC XLP low-power microcontroller rated at 32 MHz, with 16 KB of Flash program memory, 1 KB of RAM, and 512 bytes of EEPROM in a 48-UQFN 6 x 6 mm package with an exposed pad. It integrates a 12-bit ADC, DAC, and operational amplifiers for compact analog-control designs. A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The PIC24F16KM104 belongs to the PIC24F family of low-power 16-bit microcontrollers, positioned above general-purpose 8-bit devices for applications requiring greater processing performance, analog integration, and configurable control peripherals. Its nanoWatt XLP design approach targets low-power embedded systems operating from 1.8 V to 5.5 V. Key features include a 16-bit PIC core, 5.5K x 24-word Flash organization, 1 KB of SRAM, and 512 bytes of EEPROM. The analog subsystem combines a 12-bit ADC with a DAC and operational amplifiers, reducing the need for separate components in sensor, control, and signal-conditioning systems. Flexible capture, compare, and PWM modules support timing, motor-control, and waveform-generation tasks. The device uses a compact 48-UQFN package, making it suitable for space-constrained products while still exposing a substantial peripheral set. Its operating-voltage range supports both 3 V and 5 V equipment, while low-power features suit battery-operated instruments, environmental monitors, industrial sensing nodes, and consumer controls. The integrated analog functions make it particularly relevant to designs that require measurement, control output, and programmable gain or signal conditioning in one device. Typical uses include industrial sensor interfaces, compact data-acquisition modules, environmental monitors, building-control nodes, motor and actuator controllers, and low-power consumer products. Designers can connect external sensors to the ADC, generate an analog reference or control voltage through the DAC, and use the operational amplifiers for local signal conditioning. PCB implementation should follow the manufacturer pin-description table and place bypass capacitors close to the power pins. The exposed thermal pad must be connected to the intended ground plane according to the package drawing, with adequate copper area for heat dissipation. Decoupling, analog grounding, and signal-routing decisions are especially important when the ADC, DAC, and operational amplifiers operate in the same compact assembly. This product page combines the device specifications, ordering information, package details, practical application guidance, and a constrained drop-in comparison. Because the MCU integrates program memory, RAM, EEPROM, ADC, DAC, and operational amplifiers, firmware and board validation should verify the complete peripheral mix before it replaces a less integrated design.

RFQ Contact
PIC24F16KM104-E/PT - 16-Bit 32MHz MCU | Microchip Technology
PIC24F16KM104-E/PT

PIC24F16KM104-E/PT - 16-Bit 32MHz MCU | Microchip Technology

The Microchip Technology PIC24F16KM104-E/PT is a 16-bit PIC24F KM-series microcontroller with a 32 MHz processor core, 16 KB of Flash program memory, 1 KB of RAM, and 512 bytes of EEPROM in a 44-TQFP package measuring 10 mm by 10 mm. It supports operation from 1.8 V to 5.5 V and integrates a 12-bit ADC, DAC, and operational amplifiers. A microcontroller is a programmable control component that combines a processor core, memory, peripherals, and communication interfaces on one integrated circuit. The PIC24F KM family belongs to the broader embedded-control hierarchy of low-power microcontrollers, mixed-signal systems, and semiconductor devices. This combination of digital processing and analog peripherals allows compact designs to sense physical inputs, control outputs, and communicate with external equipment without requiring several discrete components. PIC24F16KM104-E/PT provides 16 KB of Flash memory organized as 5.5K words by 24 bits, together with 1 KB of data RAM and 512 bytes of nonvolatile EEPROM. Its 32 MHz processing rate supports responsive control tasks, while the integrated analog resources reduce board area. The device also includes I2C, SPI, UART/USART, IrDA, and LINbus connectivity according to the manufacturer product information. The -E/PT ordering designation identifies the extended-temperature automotive-grade variant in a 44-lead TQFP tray package. This distinction is important because the same base device can also appear with different temperature grades, package forms, and packing options. Automotive qualification requirements should be confirmed against the complete ordering table before production release rather than inferred from the ordering code alone. Typical uses include low-power sensor nodes, compact industrial controls, automotive accessory modules, battery-powered instrumentation, and communication-enabled monitoring equipment. The mixed-signal peripherals are particularly useful where a board must measure an analog input and condition or generate an analog output while retaining serial connectivity for a host controller or service interface. Designers should account for analog reference quality, ADC acquisition time, DAC settling behavior, and the current limits of each I/O pin. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be configured according to the manufacturer's guidance. The package has 44 terminals, so pin assignment and trace routing should follow the official pin-description table in the manufacturer datasheet. This product summary combines the core memory, processing, analog, interface, package, and ordering characteristics with practical guidance for MCU-based designs. It also distinguishes the documented device from temperature-grade and package alternatives that may appear in searches but are not automatically interchangeable without checking the complete ordering information.

RFQ Contact
PIC24F16KM104-I/ML - 16-Bit 32MHz 16KB Flash XLP MCU | Microchip
PIC24F16KM104-I/ML

PIC24F16KM104-I/ML - 16-Bit 32MHz 16KB Flash XLP MCU | Microchip

The Microchip Technology PIC24F16KM104-I/ML is a 16-bit PIC® XLP™ eXtreme Low Power microcontroller featuring a 32 MHz MIPS core, 16 KB (5.5K x 24) of program Flash, 1 KB of SRAM, and 512 bytes of EEPROM, housed in a 44-pin QFN (8x8 mm) package. It operates across a wide 1.8 V to 5.5 V supply range and integrates a 12-bit ADC, 8-bit DAC, op amps, comparators, and configurable MCCP/SCCP timer/PWM modules. A microcontroller (MCU) is a single-chip computer that combines a processor core, program and data memory, and programmable peripherals. The PIC24F family uses a 16-bit modified Harvard architecture running at up to 32 MHz, offering roughly 16 MIPS of throughput with deterministic interrupt latency. Within the broader hierarchy, the PIC24F sits between 8-bit PIC16/PIC18 parts and 32-bit PIC32 families, occupying the low-power 16-bit segment. The KM1xx sub-family adds integrated analog (12-bit ADC, DAC, op amps) for sensor-interface designs without external signal-chain components. Key features include XLP technology (sub-uA sleep currents, battery-friendly), a CTMU for capacitive touch and mTouch® capacitive sensing, multiple I/O ports with interrupt-on-change, and configurable logic cells that emulate small glue-logic functions. The device supports USB and UART/SPI/I²C serial interfaces through PPS (Peripheral Pin Select), giving flexible pin mapping. Typical applications include IoT sensor nodes, battery-powered portable instruments, consumer appliances, industrial control, USB peripherals, capacitive-touch human-interface panels, and low-power remote controls. The integrated 12-bit ADC and op amps reduce BOM cost in analog-front-end designs. When designing, leverage the XLP sleep modes (deep sleep, RTCC, DSGPR) to maximize battery life, place the 0.1 µF VDD decoupling cap as close to the pins as possible, and use PPS to route peripherals efficiently. Note that this I/ML variant is industrial-grade (-40 °C to +85 °C); choose the E/ML variant for extended -40 °C to +125 °C operation. This page synthesizes verified distributor pricing, drop-in alternative cross-references, and practical design notes not found in the bare manufacturer datasheet.

RFQ Contact
PIC24F16KM104-I/MV - 16-Bit 32MHz XLP Microcontroller, 48-UQFN | Microchip
PIC24F16KM104-I/MV

PIC24F16KM104-I/MV - 16-Bit 32MHz XLP Microcontroller, 48-UQFN | Microchip

Microchip Technology PIC24F16KM104-I/MV is a 16-bit PIC24 XLP ultra-low-power microcontroller with 16 KB (5.5K x 24 words) of Flash program memory, 1 KB of SRAM, 512 x 8 bits of data EEPROM, and a 32 MHz maximum clock speed, packaged in a 48-pin UQFN (6 x 6 mm) surface-mount package. It operates from 1.8 V to 3.6 V across 22 analog-to-digital converter channels with selectable 10-bit or 12-bit resolution and 38 general-purpose I/O pins. A microcontroller is a programmable system-on-chip that combines a CPU core, non-volatile program memory, data memory, and peripherals such as ADC, timers, and communication interfaces in one package. The PIC24 family uses a 16-bit modified Harvard architecture with a 16-bit instruction set and 24-bit address space, positioned between 8-bit MCUs and 32-bit Cortex-M devices. The XLP designation identifies Microchip's nanoWatt eXtreme low-power family, built for battery-operated and always-on embedded products. Key features of this device include an internal high-precision oscillator, Configurable Logic Cell (CLC) peripherals for hardware logic functions, flexible Capture/Compare/PWM modules, and a 12-bit ADC. The low pin-count 48-UQFN footprint measures only 6 x 6 mm, so it suits dense consumer and industrial control boards where board area is at a premium. Architecturally, the PIC24F16KM104 family members share the same 16-bit core and peripheral set, with Flash density and analog options scaling across the KM series. The '-I/MV' suffix denotes the industrial temperature grade (-40 C to +85 C) supplied in the 48-pin 6 x 6 mm UQFN package, giving designers a single-source path for compact, low-power control designs with no external crystal required. Typical applications include battery-powered sensor nodes and portable instrumentation, compact consumer appliances with keypad and LED interfaces, motor and lighting control using the PWM modules, and mixed-signal measurement products that need several ADC channels close to the MCU. The CLC peripherals can handle debouncing, pulse counting, or simple combinational logic, reducing the need for extra glue logic. When designing with this part, plan the decoupling strategy for a 6 x 6 mm UQFN package: place 100 nF ceramic capacitors at each supply pin and follow the exposed thermal pad with a filled and stitched ground or thermal via array. Keep analog inputs away from switching nodes, and confirm the 1.8 V to 3.6 V operating window against the supply tolerances of your end product. This page consolidates device specifications, a drop-in alternative shortlist, and practical PCB and low-power design notes that go beyond the headline parameter list, helping engineers qualify the PIC24F16KM104-I/MV for compact, low-power embedded designs in a single reference.

RFQ Contact
PIC24F16KM104-I/PT - 16-bit XLP MCU 16KB Flash TQFP-44 | Microchip
PIC24F16KM104-I/PT

PIC24F16KM104-I/PT - 16-bit XLP MCU 16KB Flash TQFP-44 | Microchip

The Microchip PIC24F16KM104-I/PT is a 16-bit PIC microcontroller from the eXtreme Low Power (XLP) family, featuring 16KB Flash, 1KB RAM, and 512B EEPROM, housed in a 44-pin TQFP (10x10 mm) package. It integrates a 12-bit ADC, DAC, comparators, op amps, and Configurable Logic Cells (CLC), targeting low-power embedded applications from 1.8V to 5.5V operation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripheral interfaces such as timers, ADCs, and communication ports. The PIC24F family specifically belongs to the 16-bit MCU hierarchy: PIC24F -> PIC24 -> 16-bit MCU -> microcontroller -> embedded processor. The "XLP" branding indicates nanoWatt Xtreme low-power technology, which provides sleep currents in the nanoampere range, making PIC24F devices suitable for battery-powered applications. Key features of the PIC24F16KM104-I/PT include a 32MHz maximum CPU speed (with instruction cycle support of up to 16 MIPS), integrated 12-bit ADC with multiple channels, on-chip op amps and comparators for analog signal conditioning, Configurable Logic Cells (CLC) for custom digital logic without external gates, and multiple PWM/SCCP/MCCP timer modules for motor control and waveform generation. The wide 1.8V-5.5V operating range allows direct connection to both 3.3V and 5V system rails. Technical depth: the device employs a 16-bit modified Harvard architecture with separate program and data buses for efficient instruction fetch and data access. The nanoWatt XLP technology provides multiple power-saving modes including Sleep, Idle, and Doze, with peripheral modules individually gated to minimize dynamic power consumption. Hardware peripherals like the CLC and Peripheral Pin Select (PPS) reduce external component count. Typical applications include IoT sensor nodes, battery-powered medical devices, consumer electronics remote controls, low-power wireless sensor hubs, and small motor control boards. The combination of analog integration and low power makes the PIC24F16KM104-I/PT particularly attractive for portable instrumentation. Design consideration: when migrating firmware across PIC24F variants, verify that the new device supports the same peripheral set; PPS remapping allows flexibility but requires careful reconfiguration. For battery applications, select the deep-sleep mode with RTCC enabled to achieve sub-microamp quiescent current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ Contact
PIC24F16KM104T-I/ML - 16KB Flash 16-bit MCU 44-QFN | XLP™ Low Power
PIC24F16KM104T-I/ML

PIC24F16KM104T-I/ML - 16KB Flash 16-bit MCU 44-QFN | XLP™ Low Power

The Microchip Technology PIC24F16KM104T-I/ML is a 16-bit PIC microcontroller from the PIC24F XLP™ KM family, featuring 16KB (5.5K x 24) of Flash program memory, 1KB of SRAM, and 512B of EEPROM, all housed in a 44-pin QFN (8x8 mm) package with exposed thermal pad. It operates from 1.8V to 5.5V with a 32MHz maximum CPU clock, integrating a 12-bit ADC, 12-bit DAC, op amps, comparators, Configurable Logic Cells (CLC), and MCCP/SCCP timer/PWM modules. The 'T' suffix denotes Tape and Reel packaging, while the 'I' indicates the industrial -40C to +85C temperature range. A PIC24F microcontroller belongs to Microchip's 16-bit PIC architecture family, which sits between the 8-bit PIC16/PIC18 devices and the higher-performance dsPIC/PIC32 families. The PIC24F series is engineered for low-power and mixed-signal applications, with the XLP™ (eXtreme Low Power) technology and nanoWatt XLP feature set providing deep sleep currents in the microamp range and multiple power modes that make it well suited to battery-powered and energy-harvesting designs. Within Microchip's portfolio, the PIC24F KM family specifically addresses low pin-count, mixed-signal embedded applications requiring integrated analog peripherals alongside digital logic. Key features include the integrated 12-bit ADC with up to 28 input channels, three operational amplifiers usable for signal conditioning, a 5-bit DAC plus a 10-bit reference DAC, four Configurable Logic Cells that emulate simple glue logic in hardware, and multiple Capture/Compare/PWM modules for motor and lighting control. The 16KB Flash and 1KB SRAM provide adequate headroom for typical sensor fusion, IoT end-node, and human-interface applications. Typical applications include low-power IoT sensor nodes, battery-powered portable medical and wearable devices, industrial sensor conditioning, LED lighting control, and small motor control subsystems. The combination of integrated analog peripherals (op amps, DAC, comparators, ADC) on a low-pin-count QFN reduces BOM cost and PCB area compared with discrete solutions. When designing with this MCU, ensure proper decoupling per Microchip's analog reference design guidelines and verify sleep-mode current targets early in the design cycle, as the 32MHz operating point and peripheral activation significantly affect nanoWatt XLP performance.

RFQ Contact
PIC24F16KM104T-I/MV - 16KB Flash XLP 16-Bit MCU | Microchip
PIC24F16KM104T-I/MV

PIC24F16KM104T-I/MV - 16KB Flash XLP 16-Bit MCU | Microchip

The Microchip Technology PIC24F16KM104T-I/MV is a 16-bit PIC24F microcontroller with 16KB of Flash program memory (5.5K x 24 words), 1KB of SRAM, and 512B of EEPROM, housed in a 48-pin UQFN 6x6 mm package with exposed thermal pad. The part is qualified for industrial -40C to +85C operation, executes instructions at up to 32 MHz (8 MIPS), and integrates a 12-bit ADC, multiple 16-bit timers, configurable logic cells (CLC), and dual MCCP/SCCP PWM/capture/compare peripherals. What is a 16-bit microcontroller? A 16-bit MCU (microcontroller) is a single-chip computer with a 16-bit data path, 16-bit registers, and 16-bit arithmetic/logic unit. Within the broader taxonomy it is a microcontroller -> embedded controller -> integrated circuit -> semiconductor. The PIC24F family sits between 8-bit PIC16/PIC18 MCUs and 32-bit PIC32 devices, offering an upgrade path with stronger peripherals and more code space while keeping nanoWatt XLP extreme-low-power features. The PIC24F16KM104T-I/MV distinguishes itself through the nanoWatt eXtreme Low Power XLP technology platform, multiple sleep modes that draw microampere-level currents, configurable logic cells that replace small external CPLD/74-series glue, and 12-bit ADC with on-chip reference. It is also available in dual-voltage variants: PIC24F products operate at 1.8V-3.6V while PIC24FV versions support 2.0V-5.5V for 5V tolerant designs. Internally, the device uses a modified Harvard architecture with separate program and data buses, a hardware multiplier for DSP-style operations, and a flexible peripheral pin-select (PPS) mapping layer that lets peripheral functions be remapped to multiple physical I/O pins, simplifying PCB layout. Typical applications include battery-powered IoT sensor nodes, portable medical monitoring electronics, consumer remote controls, low-power industrial sensor hubs, and USB/HID human-interface devices. The combination of CLC, MCCP/SCCP PWM and 12-bit ADC makes it well-suited to motor-control and LED-lighting driver signal paths. When designing with this device, mind the 48-UQFN exposed pad - it must be soldered to a sufficient copper pour for thermal dissipation and electrical grounding. Decoupling should place 100nF X7R capacitors adjacent to each VDD/VSS pair. This page synthesizes distributor pricing, same-family PIC24F drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ Contact
PIC24F16KM104T-I/PT - 16-bit XLP MCU 32MHz 16KB Flash TQFP-44
PIC24F16KM104T-I/PT

PIC24F16KM104T-I/PT - 16-bit XLP MCU 32MHz 16KB Flash TQFP-44

The Microchip Technology PIC24F16KM104T-I/PT is a 16-bit PIC® XLP™ 24F microcontroller featuring a 32 MHz core, 16 KB of Flash program memory, 1 KB of SRAM, and 512 bytes of EEPROM, housed in a 44-pin TQFP (10x10 mm) package. It belongs to Microchip's eXtreme Low Power (XLP) family, optimized for battery-powered and energy-harvesting applications that demand long runtime from small cells. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripherals such as timers, communication interfaces, and analog channels. The PIC24F belongs to Microchip's 16-bit modified-Harvard architecture family, positioned above 8-bit PIC MCUs in computational performance and peripheral integration. It sits within the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. Key features of this part include nanoWatt XLP sleep currents as low as 20 nA in deep sleep, multiple communication peripherals (I2C, SPI, UART, IrDA, and LIN), configurable logic cells (CLC), and a 12-bit ADC with multiple input channels. The integrated 32 MHz internal oscillator eliminates the need for an external crystal in many designs, reducing BOM cost and PCB area. The PIC24F architecture uses a 16-bit modified-Harvard core with a 24-bit instruction word, enabling 32 MHz operation (16 MIPS) while retaining the deterministic interrupt response that PIC MCUs are known for. Peripheral features include up to 5 CCP/ECCP modules, multiple 16-bit timers, a hardware Real-Time Clock/Calendar (RTCC), and charge time measurement unit (CTMU) for capacitive touch sensing. Typical applications include low-power IoT sensor nodes, battery-powered medical devices such as glucose meters and portable monitors, automotive LIN nodes for body and comfort electronics, industrial sensor transmitters, and consumer products requiring ultra-long battery life. The wide operating voltage range supports both 3V lithium and 1.8V-3.6V regulated supplies. When designing with this device, the integrated 32 MHz oscillator and internal LDO simplify power-tree design; place decoupling capacitors (100 nF plus 10 µF bulk) within a few millimeters of the VDD pins to minimize digital switching noise on the analog rails. This page synthesizes distributor pricing, drop-in TQFP-44 alternatives from the same Microchip PIC24F family, and practical low-power design notes that are not collected in the manufacturer datasheet itself.

RFQ Contact