بەرهەمەکان (3,600+)

AD7490BRU-REEL - 12-Bit 1MSPS 16-Ch SAR ADC, 28-TSSOP | ADI
AD7490BRU-REEL

AD7490BRU-REEL - 12-Bit 1MSPS 16-Ch SAR ADC, 28-TSSOP | ADI

The Analog Devices AD7490BRU-REEL is a 12-bit, 1 MSPS, 16-channel successive-approximation analog-to-digital converter (SAR ADC) in a 28-pin TSSOP package, supplied on tape-and-reel. According to the AD7490 datasheet (Rev -, available from analog.com), the device operates from a single 2.7 V to 5.25 V supply and integrates a low-noise, wide-bandwidth track-and-hold amplifier capable of handling input frequencies in excess of 1 MHz, with throughput rates up to 1 MSPS. What is a SAR ADC? A successive-approximation register analog-to-digital converter is a medium-speed, medium-resolution ADC architecture that uses a binary-search algorithm and an internal capacitive DAC to convert an analog input to a digital code one bit per conversion step. Within the broader taxonomy, SAR ADCs sit between flash converters (highest speed, lowest resolution) and delta-sigma ADCs (highest resolution, lower speed). The AD7490's 12-bit resolution and 1 MSPS throughput place it in the mainstream industrial data-acquisition tier used for multi-channel sensor monitoring. Key features include 16 single-ended analog input channels with on-chip sequencing, a flexible serial interface compatible with DSP, MICROWIRE, QSPI, and SPI, and low power consumption of 5.4 mW maximum at 870 kSPS with 3 V supplies, rising to 12.5 mW maximum at 1 MSPS. The TSSOP-28 (4.40 mm body width) package provides a compact footprint while exposing the analog and digital domains on opposite sides of the pinout for easier board layout. The AD7490 uses a charge-redistribution DAC architecture combined with an input track-and-hold that supports input bandwidths exceeding the Nyquist limit of the 1 MSPS sample rate, allowing accurate sampling of AC inputs without an external buffer. The on-chip channel sequencer allows the user to pre-program a sequence of up to 16 channels, reducing host-processor overhead and simplifying multi-channel data-acquisition firmware. Typical applications include industrial process control, multi-channel data acquisition systems, portable battery-powered instrumentation, motor control feedback, and medical patient monitoring where multiple sensor channels must be digitized with deterministic latency. When designing with this part, populate the recommended bypass network on AVDD/DVDD rails and respect the analog/digital ground split documented in the datasheet to avoid code-dependent noise coupling. The internal sequencer can be bypassed for software-driven channel selection, but external anti-aliasing RC filtering on each analog input remains essential. This page synthesizes distributor pricing, drop-in alternative listings, and practical design guidance not aggregated elsewhere, enabling a faster, more confident selection decision for engineers.

RFQ پەیوەندی
AD7492AR-5 - 12-Bit 1.25 MSPS ADC | Analog Devices
AD7492AR-5

AD7492AR-5 - 12-Bit 1.25 MSPS ADC | Analog Devices

Analog Devices AD7492AR-5 is a 12-bit, single-channel successive-approximation analog-to-digital converter with a maximum sampling rate of 1.25 MSPS, parallel data output, and integrated reference and clock in a 24-lead SOIC package. It operates from a single 2.7 V to 5.25 V supply and supports low-power acquisition of analog signals. An ADC is a data-conversion semiconductor that converts a continuous analog voltage into a digital code. The AD7492 belongs to the successive-approximation ADC family, commonly called a SAR ADC, within the broader analog-to-digital converter and data-converter IC hierarchy. Its parallel interface presents each 12-bit conversion result across dedicated output lines, making it suitable for systems that can capture and process a result rapidly after conversion. The AD7492 family combines resolution, throughput, and low power in a compact surface-mount package. Key characteristics include 12-bit conversion resolution, throughput up to 1.25 MSPS, one analog input, a parallel word-access interface, and operation from one 2.7 V to 5.25 V supply. The -5 suffix identifies the 1.25 MSPS member of the AD7492 family, while AD7492AR uses the 24-lead SOIC option represented by the R package code. Internally, the converter uses successive-approximation conversion, progressively refining the sampled analog voltage into a 12-bit digital result. An integrated reference and clock reduce the number of external support components required for basic operation. Because the converter uses a parallel data interface, the PCB must route 12 data lines in addition to control and power signals, making pin assignment and signal-integrity layout important at the board level. Typical applications include industrial process control, instrumentation, sensor acquisition, communications equipment, and embedded measurement systems. It is particularly appropriate when a system requires moderate resolution, sampling rates up to 1.25 MSPS, and a direct parallel interface rather than a serial protocol such as SPI or I2C. The principal design considerations are source impedance, input settling time, reference behavior, digital-output timing, and supply decoupling. Place input and bypass capacitors close to the relevant device pins, use short digital traces, and maintain the required acquisition interval so the sampled input settles before conversion begins. This page combines the AD7492AR-5 device specifications, a practical replacement assessment, package-level design guidance, and application-focused selection criteria to support faster engineering decisions beyond a basic catalog listing.

RFQ پەیوەندی
AD7492ARUZ-5-REEL - 12-Bit 1.25 MSPS SAR ADC | Analog Devices
AD7492ARUZ-5-REEL

AD7492ARUZ-5-REEL - 12-Bit 1.25 MSPS SAR ADC | Analog Devices

The Analog Devices AD7492ARUZ-5-REEL is a 12-bit, 1.25 MSPS successive-approximation analog-to-digital converter (SAR ADC) with a built-in 2.5 V reference and internal clock, housed in a 24-pin TSSOP (RU-24) package. It features a single-ended analog input (0 V to 2.5 V or 0 V to VDD), parallel (12-bit) data interface, and operates from a single 2.7 V to 5.25 V supply while consuming only 4 mW typical power at full throughput. The -5 speed grade delivers the highest sample rate in the AD7492 family, with a BUSY-asserted conversion time of 680 ns followed by immediate data readout (no pipeline delay). A SAR ADC is a type of data converter that converts an analog input voltage to a digital code through successive comparison against a precision reference, generating one conversion per acquisition cycle without latency. SAR ADCs sit in the broader hierarchy of data converters between flash ADCs (fastest, highest power) and sigma-delta ADCs (highest resolution, slowest). They are the workhorse of industrial, instrumentation, and motor-control applications where deterministic single-shot latency and moderate-to-high throughput are required. Key features of the AD7492ARUZ-5 include 1.25 MSPS throughput (the -5 grade), a 10 MHz input bandwidth track-and-hold front-end capable of handling full-scale step inputs without distortion, low 4 mW power dissipation at 1.25 MSPS, and a hardware-driven sleep mode (shutdown pin) that drops supply current to under 1 µA between conversions. The internal clock and reference remove two analog components from the BOM, easing layout and reducing bill-of-materials cost. Architecturally, the AD7492 uses a charge-redistribution capacitor DAC as the successive-approximation core, coupled to a high-bandwidth input SHA. The reference can be internal (2.5 V) or externally overdriven up to VDD for scaled input ranges, giving flexibility for both 3.3 V and 5 V analog rails in mixed-signal designs. Typical applications include industrial process control loops, data-acquisition front-ends, motor-control current sensing, optical-sensor signal chains, and portable instrumentation where low power and small PCB area are critical. The TSSOP-24 footprint eases routing alongside modern microcontrollers and DSPs with parallel bus interfaces. When designing with this part, ensure that the VDRIVE logic supply (or VDD) matches the host controller's I/O voltage to avoid level shifters, and place the 0.1 µF VDD decoupling cap within 5 mm of the supply pin. The shutdown pin can be used to stagger multi-channel sampling or to drop system quiescent current in battery-powered applications during sleep intervals. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
AD7492BR-5 12-Bit 1.25 MSPS SAR ADC | Analog Devices
AD7492BR-5

AD7492BR-5 12-Bit 1.25 MSPS SAR ADC | Analog Devices

The Analog Devices AD7492BR-5 is a 12-bit, single-channel successive-approximation-register (SAR) analog-to-digital converter in a 24-pin SOIC package. It is identified as a 5 V device with single-ended input, parallel output, and throughput rates up to 1.25 MSPS. The AD7492 family operates from a single 2.7 V to 5.25 V power supply, covering common industrial, instrumentation, communications, and embedded measurement supply rails. An ADC is a data-acquisition IC that converts an analog voltage into a digital code. SAR ADCs perform conversion through repeated comparison of the input voltage with a reference-derived voltage. This architecture is widely used for moderate-speed measurement because it provides predictable sampling behavior, compact implementation, and direct digital output for downstream processing. The AD7492 belongs to the ADC > data converter > integrated circuit hierarchy and is designed for applications that require more resolution than a low-resolution sensor interface but do not require the throughput of a high-speed pipeline converter. The AD7492BR-5 is specified as a 12-bit converter with a 1.25 MSPS maximum throughput, while one product listing describes the AD7492BR as a 1 MHz device. The distinction may reflect package or listing variation, so the manufacturer product page and datasheet should control the final design limit. The device uses a single-ended input, making it suitable for unipolar analog measurements that can be referenced to ground. Its parallel output interface is appropriate for systems in which digital data is captured directly by a controller or FPGA. Typical uses include industrial process monitoring, sensor signal acquisition, laboratory measurement equipment, communications infrastructure, and embedded control systems. The 24-pin SOIC package provides a conventional surface-mount footprint and exposed lead access for automated assembly. Designers should confirm the exact timing, input range, reference requirements, acquisition circuitry, and logic levels against the manufacturer datasheet before releasing a production design. The principal design consideration is input conditioning. The ADC should be driven through a suitable front end that limits out-of-band noise, protects the input from transients, and provides the required settling behavior for the selected sample rate. Keep the analog input path short, maintain a stable return path, and place bypass and reference-decoupling capacitors close to their associated pins. The manufacturer’s recommended application circuit should be followed when defining impedance, filtering, and layout. This page combines the AD7492 family specifications, package information, pricing references, candidate drop-in alternatives, and application guidance into one engineering-oriented resource. It also highlights the distinction between general ADC functionality and the specific electrical and timing requirements that must be confirmed before substituting a converter on an existing PCB.

RFQ پەیوەندی
AD7492BRZ - 12-Bit 1 MSPS SAR ADC | Analog Devices
AD7492BRZ

AD7492BRZ - 12-Bit 1 MSPS SAR ADC | Analog Devices

The Analog Devices AD7492BRZ is a 12-bit, single-input, successive-approximation analog-to-digital converter in a 24-lead SOIC package. The AD7492 operates from a 2.7 V to 5.25 V supply, converts at up to 1 MSPS, and consumes approximately 4 mW at that rate. Its input range is 0 V to 2.5 V, making it suitable for precision acquisition systems that require compact, low-power SAR conversion. A successive-approximation ADC, or SAR ADC, repeatedly compares the analog input with a generated reference voltage and adjusts a binary-weighted internal DAC until the comparator output changes state. This architecture combines predictable conversion latency with low power consumption and moderate resolution. The AD7492 belongs to the ADC hierarchy of data-converter ICs, providing a practical bridge between a continuously varying sensor signal and a digital value produced by a microcontroller, DSP, or programmable logic controller. The AD7492BRZ provides a 12-bit conversion result, one analog input channel, an internal reference and clock, and a low-power operating mode. According to the manufacturer product information, the AD7492 family includes AD7492, AD7492-4, and AD7492-5 variants with maximum throughput rates of 1 MSPS, 400 kSPS, and 1.25 MSPS respectively. The target AD7492 variant therefore balances conversion speed against power consumption while retaining a 12-bit output resolution. The device uses a conversion-controlled SAR architecture without pipeline delay. The BUSY indication rises at the start of conversion and falls 880 ns later for the AD7492 and AD7492-4 variants to signal completion. This deterministic behavior supports software-controlled acquisition, but it also means the host processor must observe conversion timing or use the BUSY signal when transferring each 12-bit result. The internal reference and clock reduce external component count in compact instrumentation designs. Typical uses include industrial process monitoring, temperature and pressure sensor acquisition, battery-powered measurement instruments, motor and power-system monitoring, laboratory data acquisition, and embedded control systems. The 24-lead SOIC package provides a conventional surface-mount option, while the 2.7 V to 5.25 V operating supply supports both 3.3 V and 5 V systems. The industrial-grade temperature range extends from -40 °C to 85 °C. Designers should treat the analog input as a high-impedance sampling node and use the pin-description and application-circuit guidance in the manufacturer datasheet when assigning traces and external components. Reference and supply bypassing must follow the recommended values and placement, because settling time at the input directly affects conversion accuracy. Digital output timing should also be checked against the host interface requirements before fixing the acquisition rate. This page combines the AD7492 family specifications, package information, commercial sourcing details, and engineering guidance with a focus on practical selection. It also distinguishes the standard AD7492 from its lower-speed and higher-speed family variants, helping designers choose the correct member without confusing throughput differences with pin compatibility.

RFQ پەیوەندی
AD7495ARM-REEL - 12-Bit 1 MSPS SAR ADC | Analog Devices
AD7495ARM-REEL

AD7495ARM-REEL - 12-Bit 1 MSPS SAR ADC | Analog Devices

The Analog Devices AD7495ARM-REEL is a 12-bit, high-speed, low-power successive-approximation register (SAR) analog-to-digital converter that operates from a single 2.7 V to 5.25 V supply with throughput rates up to 1 MSPS. The device is housed in an 8-pin MSOP (RM-8) package and ships on a 7-inch Tape & Reel carrier. An SAR ADC (Successive-Approximation Register Analog-to-Digital Converter) is a type of data converter that uses a binary search algorithm and an internal capacitive DAC to convert an analog input voltage into a 12-bit digital code in a single conversion cycle. SAR ADCs occupy a middle ground in the converter hierarchy between flash ADCs (which are fastest but power-hungry) and sigma-delta ADCs (which are highest-resolution but slower), and they are widely used in multiplexed data-acquisition systems, industrial process control loops, and embedded instrumentation because they deliver a fresh sample on every Nth clock edge with no pipeline latency. Key features of the AD7495ARM-REEL include a 1 MSPS guaranteed sample rate, 68 dB SNR at the analog input, a wide-input-bandwidth track-and-hold front end, an internal 2.5 V reference (the AD7475 sister part uses an external reference), and DSP/MICROWIRE/QSPI/SPI-compatible serial interface. Power consumption is rated at 4.5 mW maximum at 1 MSPS with a 3 V supply and 10.5 mW maximum at 1 MSPS with a 5 V supply. The chip offers a 0.8 µs typical conversion time and a 0-2.5 V analog input range when using the internal reference. The AD7495ARM-REEL is fabricated on a CMOS process with an integrated track-and-hold amplifier that captures fast input transients without requiring an external buffer. The internal 2.5 V reference and reference buffer are trimmed at the factory, eliminating the need for external reference components in cost-sensitive designs. A VDRIVE pin allows the digital logic interface to operate at a voltage independent from VDD, simplifying connection to 1.8 V or 3.3 V DSPs and microcontrollers. Typical applications include industrial process control, portable battery-powered instrumentation, motor control feedback loops, optical sensor front ends, and data-acquisition front ends for embedded systems. The 1 MSPS throughput makes it well-suited for sampling multiple multiplexer channels at aggregate rates of several hundred kSPS. When designing with this part, place a 0.1 µF decoupling capacitor as close as possible to VDD and VDRIVE, and route the analog input trace as a guarded microstrip to minimize digital coupling. The internal reference requires a 10 µF decoupling capacitor on REF OUT; using a smaller value increases conversion noise.

RFQ پەیوەندی
AD7495ARMZ-REEL - 12-Bit 1MSPS SAR ADC | Analog Devices
AD7495ARMZ-REEL

AD7495ARMZ-REEL - 12-Bit 1MSPS SAR ADC | Analog Devices

The Analog Devices AD7495ARMZ-REEL is a 12-bit, high-speed, low-power successive-approximation analog-to-digital converter (SAR ADC) that operates from a single 2.7 V to 5.25 V power supply with throughput rates up to 1 MSPS, packaged in an 8-pin MSOP (RM-8) tape-and-reel format. Key parameters are 12-bit resolution, 1 MSPS throughput, and an 8-pin MSOP surface-mount package. An SAR ADC is a successive-approximation-register analog-to-digital converter, a type of data converter that uses a binary search algorithm through an internal capacitive DAC to resolve each analog sample into a digital code in N conversion cycles. In the broader taxonomy, an SAR ADC sits below sigma-delta and pipeline ADCs in the precision/speed hierarchy: it offers medium resolution (typically 8 to 18 bits) and medium-to-high speed (100 kSPS to several MSPS) with very low latency and zero pipeline delay, making it ideal for multiplexed data acquisition, motor control feedback loops, and instrumentation where deterministic sampling matters more than absolute DC accuracy. Key features of the AD7495ARMZ-REEL include a low-noise wide-bandwidth track-and-hold amplifier, an on-chip 2.5 V reference, flexible VDRIVE logic supply, and SPI/QSPI/MICROWIRE/DSP-compatible serial interface. According to manufacturer characterization, the part consumes only 4.5 mW at 1 MSPS with a 3 V supply and 10.5 mW at 1 MSPS with a 5 V supply, with 70 dB signal-to-noise ratio and wide input bandwidth that supports full-scale input ranges from 0 V to VDD. The architecture is a charge-redistribution SAR with a high-impedance analog input stage that accepts unipolar single-ended inputs of 0 V to 2.5 V (when using the internal reference) or 0 V to VDD (when using an external reference). The internal reference is a low-drift 2.5 V bandgap, and the VDRIVE pin sets the logic output voltage independently of the analog supply, allowing direct connection to 1.8 V, 3 V, or 5 V microcontrollers without level shifters. Typical applications include industrial process control loops, multi-channel data acquisition systems, portable and battery-powered instrumentation, optical sensor front-ends, and motor-control current/voltage feedback. In each of these, the AD7495ARMZ-REEL provides deterministic 1 MSPS sampling, low power consumption under 11 mW, and a small MSOP-8 footprint that simplifies board layout. When designing with this ADC, size the input RC antialiasing filter around the track-and-hold acquisition time rather than the conversion time, and add a 1 nF to 10 nF ceramic bypass capacitor on VDD placed within 5 mm of the supply pin. The internal reference requires a 10 uF decoupling capacitor on the REFIN/REFOUT pin for noise performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
AD7541AJP - 12-bit CMOS Multiplying DAC, 20-PLCC | Analog Devices
AD7541AJP

AD7541AJP - 12-bit CMOS Multiplying DAC, 20-PLCC | Analog Devices

The Analog Devices AD7541AJP is a 12-bit monolithic CMOS multiplying digital-to-analog converter in a 20-pin PLCC (J-lead, 9x9 mm) surface-mount package, designed as an improved, latch-up-free successor to the industry-standard AD7541 with no Schottky protection diodes required. An MDAC (multiplying digital-to-analog converter) is a DAC whose output is the product of a digital input code and an analog reference voltage applied to the reference input. Within the broader signal-chain taxonomy, an MDAC sits between a precision voltage reference and an output op-amp, supporting applications such as digitally programmable gain, four-quadrant multiplication, and transducer excitation. Compared with non-multiplying DACs, an MDAC accepts a variable, bipolar, or AC reference and therefore can also function as a programmable attenuator or as the front end of an automatic-gain-control loop. Key specifications include 12-bit endpoint linearity (all parts guaranteed monotonic), full four-quadrant multiplication capability, TTL/CMOS-compatible parallel data interface, single +5 V to +15 V supply operation, and an operating temperature range of 0 °C to +70 °C. The thin-film-on-CMOS process delivers low noise and tight linearity at a low cost, while the latch-up-free design eliminates the output protection Schottky diodes previously required with the AD7541. Typical applications include digitally programmable gain amplifiers, four-quadrant analog multipliers, servo-motor and valve control loops, precision attenuators, waveform synthesis, function generators, and AGC circuits in instrumentation. The AD7541AJP is also commonly used as a building block in process-control and closed-loop industrial systems where a digital word directly sets an analog current or voltage. Designers should use a low-offset, low-bias-current operational amplifier in the I-to-V converter stage (e.g., OP-27, AD711, or AD8628 for higher precision) and observe standard CMOS static-discharge handling. The wide reference-input bandwidth allows the reference to be modulated for amplitude-modulation and synchronous-detection applications. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
AD7572AJRZ10-REEL - 12-Bit, 3µs SAR ADC | Analog Devices
AD7572AJRZ10-REEL

AD7572AJRZ10-REEL - 12-Bit, 3µs SAR ADC | Analog Devices

The Analog Devices AD7572AJRZ10-REEL is a 12-bit successive-approximation analog-to-digital converter (SAR ADC) with 3 µs typical conversion time, packaged in a 24-pin SOIC (0.295 inch / 7.5 mm body width) for commercial temperature grades. The converter integrates a precision buried-Zener reference, a high-speed comparator, a successive-approximation register (SAR), and a clock on-chip, providing a complete ADC solution that requires only an external analog input, a reference bypass capacitor, and a power supply. The 24-SOIC footprint matches the legacy 24-pin SOIC land pattern used throughout the AD7572 family. An SAR ADC is a class of analog-to-digital converter that performs a binary-search conversion cycle on the input voltage using an internal DAC and comparator; it offers deterministic latency, no pipeline delay, and excellent DC accuracy, making it well suited for multiplexed data acquisition systems, industrial process control, and instrumentation front-ends. Within the broader semiconductor hierarchy, the AD7572 belongs to the data-converter family of mixed-signal ICs, which sits between analog signal-chain components (amplifiers, references) and digital interface logic. Its single-supply +5 V operation simplifies integration with 5 V microcontrollers and DSPs common in legacy embedded designs. Key specifications include 12-bit resolution with no missing codes over the operating range, a 3 µs typical conversion time (approximately 333 kSPS throughput when read in burst mode), a built-in +2.5 V or +5 V reference option, and ±1 LSB maximum integral nonlinearity (INL) on the high-grade version. The parallel data interface is microprocessor-compatible, with CS and RD control inputs and an BUSY/INT status output for handshaking or interrupt-driven reads. The device operates from a single +5 V supply and supports the 0 °C to +70 °C commercial temperature range. Typical applications include process-control front ends, portable instrumentation, battery-powered measurement equipment, and legacy data-acquisition boards where a 5 V single-supply ADC with deterministic latency is required. The wide SOIC pitch (0.295 inch / 7.5 mm) and through-hole-friendly SO outline also make it a candidate for hand-soldered prototypes and educational lab kits. When designing with this part, ensure the input signal source impedance is kept low (below recommended values) to avoid charge-sharing errors on the internal CDAC, and follow the datasheet's recommended layout for the analog ground plane to minimize digital-feedthrough noise.

RFQ پەیوەندی
AD7572BQ05 - 12-Bit 5µs SAR ADC, LC2MOS, 24-CDIP | Analog Devices
AD7572BQ05

AD7572BQ05 - 12-Bit 5µs SAR ADC, LC2MOS, 24-CDIP | Analog Devices

The Analog Devices AD7572BQ05 is a 12-bit, high-speed successive-approximation analog-to-digital converter (ADC) housed in a 24-pin ceramic DIP (CDIP) package. It achieves a maximum conversion time of 5 µs and combines that speed with the low power consumption of CMOS logic, in the proprietary LC2MOS process. The part includes an on-chip buried Zener reference that delivers stable, low-drift performance over the full specified temperature range. A successive-approximation register (SAR) ADC is a type of data converter that uses a high-speed DAC, comparator, and SAR logic to iteratively narrow down an analog input to its digital equivalent. Within the converter hierarchy, the AD7572 belongs to the SAR ADC family, which sits between flash converters (fastest, lowest resolution) and sigma-delta converters (highest resolution, lower speed). At 12-bit resolution and 5 µs conversion time, the AD7572 occupies the mid-resolution speed tier that dominated 1980s and 1990s data-acquisition designs. Key features include a 5 µs maximum conversion time, an internal buried Zener reference (no external reference required), three-state digital outputs with 90 ns enable and 75 ns bus relinquish times, and a standard microprocessor interface using RD and CS signals. The 24-CDIP ceramic package provides the wide operating-temperature capability required for military and aerospace grades, indicated by the B suffix, while Q05 in the part number specifies the 5 µs conversion-time speed grade. The AD7572 uses a precision thin-film DAC and a high-speed comparator inside the SAR loop, with a buried Zener reference trimmed at the wafer stage. This architecture gives the part its signature combination of fast acquisition and low CMOS quiescent current, and it interfaces directly with most popular 8-bit and 16-bit microprocessors of its era without external latches. Typical applications include industrial process control, military and aerospace data acquisition, precision instrumentation, medical instrumentation front-ends, and DSP front-end signal conditioning. The wide temperature range also makes it suitable for harsh-environment telemetry and avionic sensor readback. When designing with this device, note that the analog input range is configured relative to the on-chip reference (typically 0 V to +2.5 V or ±2.5 V depending on input configuration). Add anti-aliasing filtering in front of the input pin and ensure clean grounding of the AGND and DGND pins to avoid digital-coupling noise in the conversion result.

RFQ پەیوەندی
AD7575TCHIPS - 8-Bit 5µs CMOS Sampling ADC Die | Analog Devices
AD7575TCHIPS

AD7575TCHIPS - 8-Bit 5µs CMOS Sampling ADC Die | Analog Devices

The Analog Devices AD7575TCHIPS is an 8-bit successive approximation register (SAR) analog-to-digital converter with a built-in track/hold function, supplied as bare die (CHIPS suffix) for hybrid and multi-chip module integration. It supports a single analog input channel and achieves a 5 µs typical conversion time, corresponding to approximately 200 kSPS throughput. The device operates from a single +5 V supply, drawing low CMOS standby current, and provides easy microprocessor interfacing via standard CS and RD control signals so the ADC can be mapped as SLOW-MEMORY or ROM. An SAR ADC is a type of analog-to-digital converter that uses a successive approximation register and an internal DAC to binary-search the input voltage, delivering deterministic latency and excellent static linearity. As part of the broader data converter hierarchy, SAR ADCs sit between flash converters (fastest, lowest resolution) and sigma-delta ADCs (highest resolution, slowest), and are the dominant architecture for 8–16 bit precision industrial sampling up to a few MSPS. The track/hold front end allows accurate conversion of fast input transients, an advantage over older integrating or flash-only designs. Key features include 8-bit resolution, 5 µs conversion time, a built-in track/hold amplifier, single +5 V supply operation, low power CMOS design, and latched three-state data outputs. All eight data outputs are latched and three-state, allowing direct connection to an 8-bit microprocessor data bus without external bus drivers. The CHIPS (die) form factor enables miniaturization in hybrid assemblies and is intended for OEM module-level packaging rather than standard PCB mounting. Architecturally, the AD7575 integrates a capacitive charge-redistribution DAC, comparator, SAR logic, and reference buffer on a single CMOS die. The CMOS process yields low power dissipation (typically tens of milliwatts during conversion) and high noise immunity. The latched three-state outputs also simplify opto-isolated or buffered data acquisition front ends. Typical applications include process control data acquisition front ends, portable instrumentation, battery monitoring systems, isolated industrial sensor interfaces, and embedded 8-bit microcontroller analog input modules. The die package makes it attractive for size-constrained medical and aerospace hybrid assemblies where standard plastic packages cannot be used. When designing with this part, allocate die bond-pad layout in advance because bare-die parts cannot accept rework. Provide a stable external reference and adequate decoupling at the supply bond pad to maintain linearity at full conversion rate. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives, and practical design notes for the AD7575TCHIPS that go beyond the manufacturer datasheet summary.

RFQ پەیوەندی
AD7582TQ/883B - 12-Bit 4-Ch SAR ADC | Analog Devices
AD7582TQ/883B

AD7582TQ/883B - 12-Bit 4-Ch SAR ADC | Analog Devices

The AD7582TQ/883B is a medium-speed, 4-channel, 12-bit CMOS successive approximation analog-to-digital converter (ADC) from Analog Devices. It features a maximum conversion time of 100 µs per channel and operates from ±5V and +15V power supplies. The device is packaged in a 28-pin ceramic dual-in-line package (CDIP) and is qualified to MIL-STD-883 Class B screening, making it suitable for military and high-reliability applications. The operating temperature range is -55°C to +125°C. An analog-to-digital converter (ADC) is an electronic component that converts continuous analog signals into discrete digital numbers. The AD7582TQ/883B uses the successive approximation register (SAR) architecture, which balances speed and resolution for medium-speed data acquisition. SAR ADCs are widely used in industrial, aerospace, and instrumentation systems where moderate sampling rates and high accuracy are required. The AD7582TQ/883B is part of the data acquisition signal chain, converting sensor outputs, voltage levels, or other analog signals into digital data for processing by microcontrollers or digital signal processors. Key features of the AD7582TQ/883B include four multiplexed input channels, a 12-bit resolution, and a maximum conversion time of 100 µs. The device includes an auto-zero cycle at the start of each conversion, which reduces offset errors and ensures low system noise. The parallel digital interface simplifies connection to microprocessors and DSPs. The MIL-STD-883 Class B screening ensures high reliability in harsh environments, with a wide operating temperature range of -55°C to +125°C. The AD7582TQ/883B is designed for medium-speed data acquisition systems that require multiple analog input channels. The four input channels can be configured for single-ended or differential inputs, providing flexibility in signal conditioning. The device requires only a few external passive components and a voltage reference, as noted in the Analog Devices product page. The auto-zero feature minimizes the need for external calibration, simplifying system design. Typical applications include military avionics, industrial process control, test and measurement equipment, and aerospace telemetry. The wide temperature range and MIL-STD-883 screening make it ideal for defense and aerospace systems where reliability is critical. The parallel interface allows direct connection to legacy 8-bit or 16-bit microprocessors, facilitating integration into existing designs. When designing with the AD7582TQ/883B, ensure that the analog input voltage does not exceed the supply rails and that adequate decoupling is provided on the power supply pins. The voltage reference should be stable and low-noise to achieve full 12-bit accuracy. The conversion time of 100 µs limits the maximum sampling rate to 10 kSPS, which should be considered for high-speed applications.

RFQ پەیوەندی
AD7606 - 16-Bit 8CH Simultaneous Sampling DAS | Analog Devices
AD7606

AD7606 - 16-Bit 8CH Simultaneous Sampling DAS | Analog Devices

The Analog Devices AD7606 is a 16-bit, 8-channel simultaneous sampling data acquisition system (DAS) that converts all eight inputs at throughput rates up to 200 kSPS while operating from a single 5 V supply and accepting true bipolar input ranges of ±10 V and ±5 V, housed in a 64-lead LQFP (10x10 mm) package. A data acquisition system (DAS) is an integrated circuit that combines signal conditioning, analog-to-digital conversion, and digital interface functions in one device. Within the converter hierarchy, the AD7606 belongs to the SAR (successive approximation register) ADC family, sits under analog-to-digital converters within the data converter / precision signal chain category, and functions as a complete power-management-friendly front end for industrial measurement systems. Key features include eight simultaneously sampled inputs, a fully integrated analog front end with input clamp protection that tolerates up to ±16.5 V at the pins, an on-chip input buffer with a 1 MΩ analog input impedance regardless of sampling frequency, and flexible digital interfaces (parallel, serial SPI, QSPI, and MICROWIRE) with a VDRIVE pin operating from 2.3 V to 5 V for direct connection to low-voltage DSPs and microcontrollers. Technically, the device employs a high-speed, low-power, charge-redistribution SAR ADC architecture with an on-chip antialiasing filter providing a 3 dB cutoff of 22 kHz and 40 dB antialias rejection when sampling at 200 kSPS. A pin-driven digital oversampling filter improves SNR and reduces signal bandwidth without host intervention. Single-supply 5 V operation plus bipolar input tolerance eliminates the need for external dual supplies, level shifters, or driver amplifiers. Typical applications include industrial motor-control and power-line monitoring, three-phase inverter and grid-quality measurement, and medical or scientific multi-channel data acquisition where true bipolar sensors must be sampled simultaneously. A key design consideration is that all eight channels share one 200 kSPS conversion cycle; the antialiasing filter bandwidth and oversampling ratio should be chosen together to balance noise against settling behavior at the input buffer. This page synthesizes distributor pricing, verified drop-in alternatives such as the AD7606B and GX7606, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
AD7606BBCHIPS - 16-Bit 8-Ch 800kSPS DAS ADC | Analog Devices
AD7606BBCHIPS

AD7606BBCHIPS - 16-Bit 8-Ch 800kSPS DAS ADC | Analog Devices

The Analog Devices AD7606BBCHIPS is a 16-bit, simultaneous sampling, analog-to-digital data acquisition system (DAS) with eight channels, offering 800 kSPS throughput per channel with bipolar input capability. Each of the eight channels integrates analog input clamp protection, a programmable gain amplifier (PGA), a low-pass filter, and a 16-bit successive approximation register (SAR) analog-to-digital converter, all on a single die. A data acquisition system (DAS) is a signal-chain subsystem that converts real-world analog signals into digital data for processing. Within the ADC hierarchy, the AD7606BBCHIPS sits in the simultaneous-sampling SAR ADC family, which is preferred over multiplexed architectures when multiple channels must be sampled at exactly the same instant, such as in three-phase power measurement. Key features include true bipolar input operation from a single supply, an on-chip antialiasing filter with digitally programmable bandwidth, and a 5 MΩ analog input impedance. The high input impedance results in less than 20 LSB bipolar zero code error when an input is disconnected and pulled to ground through a 10 kΩ external resistor, eliminating the need for external bipolar-supply driver op amps. Architecturally, the AD7606BBCHIPS uses per-channel signal chains with integrated clamp protection, allowing direct connection to sensors and transformers while tolerating overvoltage faults. According to the ADI application note AN-1559, the AD7606B generation is a drop-in upgrade from the original AD7606 with higher input impedance, faster throughput, and extended temperature range. Typical applications include power line monitoring and protective relays, three-phase motor and inverter control, industrial automation DAQ modules, and medical instrumentation. The 800 kSPS simultaneous sampling across all eight channels makes it well suited to power quality analyzers and grid monitoring equipment. A key design consideration is that higher on-chip input impedance allows reduced-power signal sourcing, but the digital interface (parallel or serial SPI) must respect throughput timing when running at full 800 kSPS across all channels. Supply sequencing of the analog and digital rails should follow the datasheet power-up order. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, verified as of 2026-09-14.

RFQ پەیوەندی
AD7606BSTZ - 16-Bit 8-Ch 200kSPS Simultaneous DAS ADC | Analog Devices
AD7606BSTZ

AD7606BSTZ - 16-Bit 8-Ch 200kSPS Simultaneous DAS ADC | Analog Devices

The Analog Devices AD7606BSTZ is a 16-bit, 8-channel, simultaneous-sampling data acquisition system (DAS) housed in a 64-lead LQFP (10x10 mm) package. It integrates analog input clamp protection, a second-order antialiasing filter, a track-and-hold amplifier, a 16-bit charge-redistribution successive-approximation ADC, a 2.5V on-chip reference and reference buffer, and high-speed serial and parallel interfaces. The device accepts true bipolar input ranges of ±10V or ±5V and runs from a single 5V analog supply, with a separate 2.3V-to-5V VDRIVE rail for the digital host interface. Throughput is 200 kSPS per channel, with all eight channels sampled at the same instant on the rising edge of CONVST. A Data Acquisition System (DAS) is a complete mixed-signal front-end that conditions, samples, and digitizes multiple analog signals for a downstream host processor. The AD7606BSTZ sits in the family of simultaneous-sampling ADCs - between analog sensors and a DSP, FPGA, or microcontroller - and is a member of the broader converter hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. Simultaneous-sampling DA conversion preserves the phase relationship between channels, a property that single-channel sequentially-sampling ADCs cannot deliver. Key differentiating features include eight truly simultaneous track-and-hold channels, on-chip oversampling digital filter with 2x/4x/8x/16x/32x/64x ratios, integrated 2.5V reference with 10 ppm/°C drift, 1 MΩ analog input impedance that removes the need for external driver op-amps, and parallel/serial/SPI/QSPI/MICROWIRE-compatible digital I/O. Hardware-mode operation lets a host start conversions without writing any registers, useful for deterministic, low-latency control loops. Technically, the ADC core is a charge-redistribution SAR converter followed by a flexible digital filter. The analog front end combines ±25V tolerant input clamps, a 1 MΩ input buffer, and a second-order Butterworth antialiasing filter with a -3 dB corner near 22 kHz at 200 kSPS. The integrated reference can be overdriven by an external low-impedance source when tighter accuracy is needed. Power consumption is approximately 215 mW when all eight channels sample at 200 kSPS from ±10V inputs. Typical uses are three-phase power-line monitoring and protective relays (where phase-angle accuracy between voltage and current is critical), industrial motor control feedback, multi-axis vibration and modal analysis, and medical instrumentation. The bipolar ±10V/±5V ranges interface directly to current shunts and resistor-divider voltage networks, eliminating external signal conditioning. The eight-channel count suits four-quadrant power analyzers and multi-axis sensor pods without requiring an external mux. When designing with this device, place 10 µF + 0.1 µF decoupling capacitors close to each AVCC pin and a single 10 µF + 0.1 µF pair on VDRIVE. Drive CONVSTA and CONVSTB simultaneously to guarantee true simultaneous sampling across all eight channels. If higher DC accuracy is required, drive REFIN/REFOUT from an external low-impedance reference rather than using the internal 2.5V source. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - useful for engineers qualifying second sources or planning migrations to the newer AD7606B family.

USD $20.85 لە کۆگادایە
AD7606BSTZ - 16-Bit 8-Ch Simultaneous ADC | Analog Devices
AD7606BSTZ

AD7606BSTZ - 16-Bit 8-Ch Simultaneous ADC | Analog Devices

The AD7606BSTZ is a 16-bit, 8-channel, simultaneous sampling analog-to-digital data acquisition system (DAS) from Analog Devices. It integrates analog input clamp protection, a second-order antialiasing filter, a track-and-hold amplifier, a 16-bit charge redistribution successive approximation ADC, a flexible digital filter, a 2.5V reference and reference buffer, and high-speed serial and parallel interfaces. The device operates from a single 5V supply and accepts bipolar input ranges of ±5V and ±10V, making it ideal for power-line monitoring and industrial data acquisition. A data acquisition system (DAS) is a complete signal chain that conditions, samples, and digitizes analog signals. The AD7606BSTZ belongs to the family of simultaneous sampling ADCs, which capture multiple channels at the same instant, preserving phase relationships critical for power metering and vibration analysis. It sits between analog sensors and a digital host processor, converting real-world signals into digital words for processing. Key features include 16-bit resolution, 200 kSPS throughput per channel, 8 simultaneous sampling channels, and a 64-lead LQFP package. The device offers a parallel, serial, SPI, QSPI, and MICROWIRE interface, providing flexibility for various host controllers. The integrated 2.5V reference and buffer eliminate the need for external reference components, simplifying design and reducing BOM cost. Technically, the AD7606BSTZ uses a successive approximation register (SAR) architecture with a charge redistribution DAC. The analog front end includes a second-order antialiasing filter with a cutoff frequency of 22 kHz, which attenuates out-of-band noise. The digital filter provides programmable oversampling ratios to further reduce noise. The device operates over the industrial temperature range of -40°C to +85°C and is available in a 10x10 mm LQFP package. Typical applications include power-line monitoring, protective relays, motor control, and multi-axis vibration analysis. The simultaneous sampling capability ensures accurate phase measurement between voltage and current channels, which is essential for power quality analysis. The high input impedance and integrated protection make it robust for harsh industrial environments. When designing with the AD7606BSTZ, ensure proper decoupling of the AVCC and DVCC supplies with 10 µF and 0.1 µF capacitors placed close to the pins. The REFIN/REFOUT pin can be driven by an external reference if higher accuracy is required, but the internal 2.5V reference is sufficient for most applications. The CONVST pins should be driven simultaneously to achieve true simultaneous sampling.

USD $16.90 پەیوەندی
AD7606BSTZ-4 - 16-Bit 4-Ch Simultaneous Sampling ADC | Analog Devices
AD7606BSTZ-4

AD7606BSTZ-4 - 16-Bit 4-Ch Simultaneous Sampling ADC | Analog Devices

The AD7606BSTZ-4 from Analog Devices is a 16-bit, 4-channel simultaneous sampling analog-to-digital data acquisition system (DAS) in a 64-lead LQFP (10x10 mm) package. It operates from a single 5 V supply and accommodates true bipolar input signals of ±10 V and ±5 V while sampling at throughput rates up to 200 kSPS for all channels. The device integrates analog input clamp protection, a second-order antialiasing filter, a track-and-hold amplifier, a 16-bit charge redistribution successive approximation ADC, a flexible digital filter, a 2.5 V reference, and reference buffer. The AD7606BSTZ-4 supports multiple serial interface modes including DSP, MICROWIRE, QSPI, and SPI, as well as a parallel interface, making it versatile for various microcontroller and DSP connections. A data acquisition system (DAS) is a complete signal chain that conditions, samples, and converts analog signals into digital data for processing. The AD7606BSTZ-4 integrates the entire front-end, eliminating the need for external op-amps, filters, and references, which simplifies design and reduces board space. As a simultaneous sampling ADC, it captures all four channels at the same instant, which is critical for applications requiring phase-accurate measurements across multiple inputs, such as power monitoring and motor control. Key features include 1 MΩ analog input impedance regardless of sampling frequency, input clamp protection up to ±16.5 V, and a 3 dB cutoff frequency of 22 kHz for the antialiasing filter, providing 40 dB antialias rejection at 200 kSPS. The flexible digital filter is pin-driven, yielding improvements in SNR and reducing the 3 dB bandwidth. The device operates over the industrial temperature range of -40°C to +85°C and is RoHS compliant. The AD7606BSTZ-4 uses a charge redistribution successive approximation architecture, which offers excellent DC accuracy and low power consumption. The integrated 2.5 V reference and buffer ensure stable conversion results without external components. The device also features a flexible digital filter that can be configured via the oversampling pins to trade off throughput for noise performance, allowing designers to optimize SNR for their specific application. Typical applications include power line monitoring, protective relays, motor control, and industrial data acquisition systems. The simultaneous sampling capability and high input impedance make it ideal for measuring three-phase voltages and currents with phase accuracy. The wide input range and clamp protection ensure robust operation in harsh industrial environments. When designing with the AD7606BSTZ-4, ensure that the analog input signals are within the specified ±10 V or ±5 V ranges and that the supply decoupling is adequate. The device requires a clean 5 V supply and proper grounding to achieve the specified performance. The digital interface should be configured according to the host processor's requirements, and the oversampling pins should be set to achieve the desired balance between throughput and noise.

RFQ پەیوەندی
AD7606BSTZ-4RL - 4Ch 16-Bit 200kSPS ADC DAS | Analog Devices
AD7606BSTZ-4RL

AD7606BSTZ-4RL - 4Ch 16-Bit 200kSPS ADC DAS | Analog Devices

The AD7606BSTZ-4RL is a 4-channel, 16-bit, simultaneous sampling analog-to-digital data acquisition system (DAS) from Analog Devices, packaged in a 64-lead LQFP (10x10 mm). It integrates analog input clamp protection, a second-order antialiasing filter, a track-and-hold amplifier, a 16-bit charge redistribution successive approximation ADC, a flexible digital filter, a 2.5V reference, and reference buffer, all on a single chip. Operating from a single 5V analog supply and a 2.3V to 5V VDRIVE interface supply, it supports true bipolar input ranges of ±10V and ±5V, making it ideal for industrial power monitoring, motor control, and data acquisition systems. A data acquisition system (DAS) is a complete signal chain that conditions, samples, and converts analog signals into digital data for processing. The AD7606BSTZ-4RL belongs to the family of simultaneous sampling ADCs, which capture multiple channels at the exact same instant, preserving phase relationships critical for applications like three-phase power analysis. As a DAS, it integrates front-end protection, filtering, and conversion, reducing external component count versus discrete ADC implementations. Key features include 16-bit resolution with 200 kSPS throughput on all channels, 95.5 dB SNR, and a flexible digital filter that improves noise performance. The device offers parallel, serial SPI, QSPI, MICROWIRE, and DSP-compatible interface options. The on-chip 2.5V reference and buffer eliminate external reference components, while the 1 MΩ analog input impedance simplifies driver design. Technically, the AD7606BSTZ-4RL uses a successive approximation register (SAR) architecture with charge redistribution, achieving high accuracy and low power. The integrated second-order antialiasing filter simplifies external filtering, and input clamp protection handles overvoltage up to ±16.5V. The device operates over the industrial temperature range of -40°C to +85°C. Typical applications include power line monitoring, motor control, industrial automation, and test and measurement equipment. Its simultaneous sampling capability is essential for accurate phase measurement in polyphase power systems, while high input impedance and integrated protection make it robust for direct sensor interfacing. When designing with this device, ensure proper decoupling of AVCC and VDRIVE supplies, and tune the digital filter settings to balance noise versus throughput. Careful PCB layout is needed to minimize digital noise coupling into the analog inputs.

RFQ پەیوەندی
AD7606BSTZ-6RL - 16-Bit 6-Ch Simultaneous Sampling ADC | Analog Devices
AD7606BSTZ-6RL

AD7606BSTZ-6RL - 16-Bit 6-Ch Simultaneous Sampling ADC | Analog Devices

The AD7606BSTZ-6RL is a 16-bit, simultaneous sampling, analog-to-digital data acquisition system (DAS) with six channels, manufactured by Analog Devices. It integrates analog input clamp protection, a second-order antialiasing filter, a track-and-hold amplifier, a 16-bit charge redistribution successive approximation ADC, a flexible digital filter, a 2.5 V reference and reference buffer, and high-speed serial and parallel interfaces. The device operates from a single 5 V supply and accepts bipolar input ranges of ±10 V, ±5 V, and ±2.5 V, making it ideal for industrial power-line monitoring, motor control, and data acquisition systems. A data acquisition system (DAS) is a complete signal chain that conditions, samples, and converts analog signals into digital data for processing. The AD7606BSTZ-6RL is a specific type of DAS that combines multiple analog front-end components into a single IC, reducing board space and design complexity. It belongs to the family of simultaneous sampling ADCs, which capture all channels at the same instant, preserving phase relationships between channels—critical for applications like three-phase power monitoring where phase accuracy is essential. Key features include a 200 kSPS throughput rate per channel, 16-bit resolution with no missing codes, and a flexible digital filter that can be configured for different output word rates. The device supports multiple interface options: parallel, serial, SPI, QSPI, MICROWIRE, and DSP-compatible serial interfaces, providing design flexibility. The integrated 2.5 V reference and buffer eliminate the need for external reference components, simplifying the BOM. The analog input clamp protection ensures robustness against overvoltage conditions up to ±16.5 V. Technically, the AD7606BSTZ-6RL uses a charge redistribution successive approximation architecture, which offers excellent linearity and low power consumption. The second-order antialiasing filter provides -80 dB attenuation at the Nyquist frequency, reducing the need for external filtering. The device operates over the industrial temperature range of -40°C to +85°C and is available in a 64-lead LQFP (10x10 mm) package, suitable for space-constrained designs. Typical applications include power line monitoring, protective relays, motor control, and multi-phase data acquisition systems. The simultaneous sampling capability ensures accurate phase measurement, while the high input impedance and integrated protection make it robust for harsh industrial environments. When designing with this device, ensure proper decoupling of the AVCC and DVCC supplies with 10 µF and 0.1 µF capacitors placed close to the pins. The REFIN/REFOUT pin can be overdriven with an external reference if higher accuracy is required, but the internal 2.5 V reference is sufficient for most applications.

USD $29.80 پەیوەندی
AD7606BSTZ-RL - 16-Bit 8-Ch Simultaneous ADC | Analog Devices
AD7606BSTZ-RL

AD7606BSTZ-RL - 16-Bit 8-Ch Simultaneous ADC | Analog Devices

The AD7606BSTZ-RL is a 16-bit, 8-channel, simultaneous sampling analog-to-digital data acquisition system (DAS) from Analog Devices. It integrates analog input clamp protection, a second-order antialiasing filter, a track-and-hold amplifier, a 16-bit charge redistribution successive approximation (SAR) ADC, a flexible digital filter, a 2.5 V reference and reference buffer, and high-speed serial and parallel interfaces. The device operates from a single 5 V supply and accepts bipolar input ranges of ±5 V and ±10 V, making it ideal for industrial power-line monitoring, motor control, and multi-phase energy measurement. A data acquisition system (DAS) is a complete signal chain that conditions, samples, and converts analog signals into digital data for processing. The AD7606 integrates the entire front-end, eliminating the need for external op-amps, references, and antialiasing filters, thereby reducing board space and design complexity. As a simultaneous sampling ADC, it captures all channels at the same instant, which is critical for applications requiring phase-accurate measurements across multiple inputs. Key features include a 200 kSPS throughput rate per channel, 16-bit resolution with no missing codes, and a 2.5 V internal reference with ±1% accuracy. The device offers both serial (SPI/QSPI/MICROWIRE) and parallel interfaces, and supports daisy-chaining for multiple devices. The flexible digital filter can be configured to improve noise performance, and the analog input clamp protects against overvoltage conditions up to ±16.5 V. The AD7606 uses a charge redistribution SAR architecture, which provides excellent linearity and low power consumption. The integrated antialiasing filter simplifies external filtering requirements, and the track-and-hold amplifier ensures accurate sampling of fast-changing signals. The device operates over the industrial temperature range of -40°C to +85°C and is available in a 64-lead LQFP package. Typical applications include power line monitoring, protective relays, motor control, and multi-phase energy measurement. The simultaneous sampling capability ensures accurate phase relationships between channels, which is essential for power quality analysis. The device is also suitable for vibration analysis and other multi-channel data acquisition systems. When designing with the AD7606, ensure that the analog input range is properly configured via the RANGE pin, and that the reference decoupling capacitor is placed close to the REFIN/REFOUT pin. The digital interface should be matched to the host processor's voltage level, and the AVCC and DVCC supplies should be decoupled with 0.1 µF and 10 µF capacitors.

RFQ پەیوەندی
AD7606C-16BSTZ - 16-bit 8-ch 1MSPS Bipolar DAS ADC | ADI
AD7606C-16BSTZ

AD7606C-16BSTZ - 16-bit 8-ch 1MSPS Bipolar DAS ADC | ADI

The Analog Devices AD7606C-16BSTZ is a 16-bit, simultaneous-sampling, 8-channel data acquisition system (DAS) with 1 MSPS per-channel throughput, packaged in a 64-pin LQFP (10x10 mm) with an exposed pad. Each channel integrates analog input clamp protection, a programmable gain amplifier (PGA), a low-pass anti-alias filter, and a 16-bit successive-approximation-register (SAR) ADC, all operating from a single 5 V analog supply. A data acquisition system (DAS) is an integrated subsystem that combines multiple ADC channels with input signal conditioning, references, and interfaces so an embedded MCU, DSP, or FPGA can digitize many analog sensors simultaneously. Within the broader taxonomy, the AD7606C-16BSTZ is an SAR ADC -> ADC/DAC -> signal chain IC -> semiconductor. ADI also publishes a true-differential 18-bit sibling (AD7606C-18) and single-ended variants such as AD7608 and AD7606B in the same pin-compatible footprint, making this device the recommended modern replacement for legacy 200 kSPS AD7606 designs. Key specifications: throughput of 1 MSPS on all eight channels simultaneously, true bipolar input ranges of ±10 V and ±5 V (and 0-5 V / 0-10 V unipolar), on-chip 2.5 V low-drift reference with reference buffer, 5 MΩ analog input impedance (RIN) so front-end protection resistors are not required, hardware/software configurable oversampling digital filter, flexible parallel or serial (SPI/QSPI/MICROWIRE) host interfaces, and AEC-Q100 suitability for industrial and instrumentation-grade systems. Design considerations: at 1 MSPS with eight channels streaming, the digital interface bus activity is heavy, so keep the LQFP exposed pad soldered to a continuous ground pour for thermal dissipation and to lower digital return impedance. For best THD and SNR, drive AVDD/REF_CAP from low-noise regulators (e.g., LT3042 / LT3045) and decouple VDRIVE independently from the 5 V AVCC rail so digital transients do not couple into the analog front end. Typical applications include three-phase power-line monitoring, multi-axis industrial motor control, simultaneous data acquisition front ends, instrumentation and test equipment, and medical multi-channel patient monitoring. According to the ADI datasheet, the AD7606C-16 family is recommended by ADI for new designs over the legacy AD7606, and the LQFP-64 footprint is shared so firmware/PCB migration is trivial.

USD $49.22 لە کۆگادایە
AD7606C-18BSTZ - 18-Bit 8-Ch 1MSPS DAS ADC | Analog Devices
AD7606C-18BSTZ

AD7606C-18BSTZ - 18-Bit 8-Ch 1MSPS DAS ADC | Analog Devices

The Analog Devices AD7606C-18BSTZ is an 18-bit, 8-channel, simultaneous-sampling data acquisition system (DAS) based on successive-approximation-register (SAR) ADC architecture, sampling at up to 1 MSPS per channel and housed in a 64-pin LQFP (10 mm x 10 mm) package. The device integrates analog input clamp protection, a programmable gain amplifier (PGA), a low-pass analog input filter, and an 18-bit SAR ADC per channel, delivering true bipolar input ranges of ±10 V, ±5 V, and 0 V to 10 V from a single 5 V analog supply. A 2.5 V on-chip low-drift precision reference and a reference buffer are included, eliminating the need for external reference components in most designs. A simultaneous-sampling SAR ADC is a category of precision data converter that captures the instantaneous voltage on all input channels at the same instant under one common convert-start signal, then performs a binary-search quantization in successive bit decisions per channel. The AD7606C-18 sits inside the hierarchy: SAR ADC -> data acquisition system (DAS) -> precision ADC -> analog-to-digital converter -> mixed-signal IC. Synchronous multi-channel acquisition is essential when phase relationships between signals must be preserved. Key features include an on-chip digital filter with oversampling ratios from 2x to 256x, integrated analog input clamps with ±16.5 V tolerance, a per-channel PGA with hardware gain settings of 1, 2, 4, 8, 16, 32, and 64, and both parallel and serial (SPI-/QSPI-/MICROWIRE-/DSP-compatible) host interfaces. Throughput remains 1 MSPS per channel across all eight channels simultaneously, with SNR of approximately 91 dB and THD near -100 dB at the maximum sampling rate. The 5 V single-supply operation simplifies system power design versus traditional ±15 V industrial front ends. The architecture pairs a high-impedance input front end (typically 1 MΩ) with a charge-redistribution SAR core, controlled by an internal precision reference and a flexible sequencer. Hardware overrange detection and per-channel sequencer flags accelerate FPGA-/DSP-side post-processing. An extended operating temperature range of -40 °C to +85 °C supports industrial deployment, and the part is rated to withstand ±16.5 V analog overvoltages on every input without damage. Typical applications include three-phase power-line monitoring and protection relays, multi-axis industrial motor control, patient monitoring ECG/EEG front ends, vibration and structural-health data loggers, and high-channel-count data acquisition modules. The combination of true bipolar inputs, simultaneous sampling, integrated analog front end, and on-chip reference makes the AD7606C-18 a single-chip replacement for legacy multi-component discrete DAS front ends. When designing with the AD7606C-18, allocate the LQFP-64 land pattern with thermal copper pour tied to the exposed pad (EP) for lowest junction-to-ambient resistance, and use 100 nF plus 10 µF decoupling on AVDD/AVDD_DR with 100 nF plus 10 µF on VDRIVE close to the device. Drive CONVST with a clean low-jitter source; jitter couples directly to the SNR budget. For best DC accuracy, allow the on-chip reference a 5 ms settling after power-up. This page synthesizes distributor stock and price tiers (DigiKey), verified drop-in alternatives, parametric comparison vs Analog Devices pin-compatible siblings, and practical PCB/thermal/decoupling notes not collated in the manufacturer datasheet alone.

USD $28.71 پەیوەندی
AD7606TSTZ-EP - 16-Bit 8-Channel Simultaneous Sampling DAS | Analog Devices
AD7606TSTZ-EP

AD7606TSTZ-EP - 16-Bit 8-Channel Simultaneous Sampling DAS | Analog Devices

The Analog Devices AD7606TSTZ-EP is a 16-bit, 8-channel simultaneous sampling data acquisition system (DAS) with a 150 kSPS per-channel throughput rate, dual true bipolar input ranges of ±10 V and ±5 V, and a single 64-pin LQFP (10x10 mm) package. It integrates analog input clamp protection, a second-order antialiasing filter, track-and-hold amplifiers, an 8-channel 16-bit charge redistribution SAR ADC, a flexible digital filter, a 2.5 V reference and reference buffer, and both high-speed serial and parallel interfaces. A data acquisition system (DAS) is a specialized analog-to-digital converter subsystem that combines signal conditioning, sampling, and conversion in one integrated circuit. Within the hierarchy of signal chain components, a DAS sits above a plain ADC: it adds input protection, filtering, and channel sequencing so a processor can digitize multiple bipolar sensors through a single device without external op amps or bipolar supplies. Key features include a 1 MΩ analog input impedance that is constant regardless of sampling frequency, single-supply operation (5 V analog, 3.3 V or 5 V digital) that eliminates driver op amps and external bipolar rails, and an antialiasing filter with a 3 dB cutoff of 23 kHz. The pin-driven digital filter improves SNR and reduces 3 dB bandwidth on demand. Interfaces include SPI, QSPI, MICROWIRE, and parallel/serial modes. As an ADI Enhanced Product (EP), the AD7606TSTZ-EP supports defense and aerospace applications under the ADI AQEC standard, with a military temperature range of -55C to +125C, a controlled manufacturing baseline, one assembly/test site, one fabrication site, product change notification, and qualification data available on request (per Analog Devices AD7606-EP product page and datasheet). Typical applications include power-line monitoring and protective relays in grid infrastructure, multi-channel industrial control and motor monitoring, and aerospace/defense instrumentation where extended temperature range and controlled manufacturing are mandatory. Design consideration: the on-chip 2.5 V reference and reference buffer remove the need for an external precision reference in most designs, but for best noise performance at 16-bit resolution, decouple the reference buffer closely and allow the digital filter to trade bandwidth for SNR. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
AD7608BSTZ - 18-Bit 8-Ch Simultaneous Sampling ADC | Analog Devices
AD7608BSTZ

AD7608BSTZ - 18-Bit 8-Ch Simultaneous Sampling ADC | Analog Devices

The Analog Devices AD7608BSTZ is an 8-channel, 18-bit, bipolar, simultaneous sampling data acquisition system (DAS) with integrated analog input clamp protection, second-order antialiasing filter, track-and-hold amplifiers, an 18-bit charge redistribution SAR ADC, a flexible digital filter, a 2.5 V reference and buffer, and high-speed parallel/serial interfaces. Housed in a 64-lead LQFP (10x10 mm) package, it operates from a single 5 V supply and accepts ±10 V, ±5 V, and ±2.5 V analog inputs with a 200 kSPS per-channel throughput. What is a data acquisition system? A DAS is a complete signal chain that conditions, samples, and converts analog signals into digital data. The AD7608 integrates all essential analog front-end functions — clamping, filtering, track-and-hold, SAR conversion, and digital interface — reducing external circuitry. As part of the simultaneous sampling ADC family, it captures all channels at the same instant, preserving phase relationships that are critical in three-phase power analysis, vibration monitoring, and motor current sensing. Key features include 18-bit resolution, 200 kSPS per channel, true simultaneous sampling across eight channels, and bipolar input ranges that eliminate external level-shifting. The second-order antialias filter has a 22 kHz 3 dB cutoff and provides 40 dB rejection at 200 kSPS. The programmable pin-driven digital filter trades bandwidth for improved SNR. The integrated 2.5 V reference and buffer maintain gain stability over temperature. Both parallel and SPI/DSP serial interfaces are available, simplifying connection to MCUs, DSPs, and FPGAs. Architecturally, the charge redistribution SAR approach provides excellent linearity and low power for a multi-channel precision converter. The input clamp protection and antialias filter simplify front-end design in harsh industrial environments. The flexible digital filter allows engineers to optimize noise versus output data rate for each application. Typical applications include power-line monitoring, protective relays, motor control, multi-phase energy metering, vibration analysis, and test and measurement instrumentation. The simultaneous sampling capability is essential for accurate phase measurement and multi-axis synchronization. The 18-bit resolution enables detection of small signal variations that 16-bit systems miss. When designing with the AD7608, place decoupling capacitors close to the AVCC and DVCC pins, and route the reference decoupling capacitor adjacent to REFIN/REFOUT. Balance the oversampling ratio against settling time so the increased digital filtering does not reduce the effective throughput below system requirements.

USD $38.18 پەیوەندی