بەرهەمەکان (3,600+)

MCP3204-CI/ST - 12-Bit 4-Channel SAR ADC | Microchip
MCP3204-CI/ST

MCP3204-CI/ST - 12-Bit 4-Channel SAR ADC | Microchip

Microchip MCP3204-CI/ST is a 12-bit, four-channel successive approximation register analog-to-digital converter with an SPI serial interface, a 100 ksps sampling rate, and a 14-pin TSSOP package. The automotive-qualified device is designed for embedded control applications requiring compact multichannel data acquisition and low-power operation. An analog-to-digital converter, or ADC, converts continuous analog voltage signals into digital values that a microcontroller or other digital controller can process. The MCP3204 belongs to the SAR ADC family, whose successive approximation architecture compares the input voltage with a internally generated reference through a successive sequence of conversion steps. Its SPI interface reduces the number of signal connections required for transferring conversion results. The MCP3204-CI/ST provides four analog input channels, 12-bit conversion resolution, and a 100 ksps conversion rate in a 14-pin TSSOP package. Its operating supply voltage begins at 2.7 V, making it appropriate for embedded systems that cannot support a 5 V-only analog interface. The automotive qualification indicated for this ordering code supports its use in vehicle-oriented electronic control systems when the complete system requirements are satisfied. The SPI interface supports integration with microcontrollers, programmable controllers, and data-acquisition systems. Four analog inputs allow one converter to serve multiple sensors or conditioned analog signals while avoiding the footprint and component count of four unrelated converter packages. The 12-bit result provides 4,096 discrete codes across the selected input range, while the 100 ksps rate supports rapidly changing measurements when the acquisition and signal-conditioning path are designed appropriately. Typical uses include automotive sensor acquisition, industrial control systems, battery and power monitoring, laboratory data acquisition, and embedded instrumentation. The converter can be paired with analog front-end circuits, voltage references, op-amp signal-conditioning stages, and SPI-capable microcontrollers. Its low-voltage operation and compact TSSOP outline are useful where board area, energy use, and deterministic serial communication are important. The principal design considerations are reference quality, input-range configuration, source impedance, acquisition timing, and SPI clocking. Input signals must remain within the selected analog range, and the sampling network should present sufficiently low impedance to the converter's sample-and-hold input. PCB traces should be kept short, reference connections stable, and digital return currents controlled to minimize conversion errors. This product page combines the manufacturer description with distributor and cross-reference information to summarize the MCP3204-CI/ST's resolution, channel count, sampling rate, interface, package, application fit, and replacement considerations. It also provides engineering-focused guidance for PCB layout, signal conditioning, and component selection.

RFQ پەیوەندی
MCP3208-BI/P - 12-Bit 8-Channel SAR ADC | Microchip
MCP3208-BI/P

MCP3208-BI/P - 12-Bit 8-Channel SAR ADC | Microchip

The Microchip Technology MCP3208-BI/P is a 12-bit successive-approximation-register analog-to-digital converter with eight input channels, one SPI serial interface, and a 16-pin PDIP package. It operates from a 2.7 V supply and is designed for embedded-control systems that need multiple analog inputs measured by a microcontroller or other SPI host. An ADC is a data-conversion IC that transforms an analog voltage into a digital code. The MCP3208 belongs to the SAR ADC family within analog-to-digital converters, interface ICs, and the broader semiconductor hierarchy. Its internal sample-and-hold circuitry acquires the input voltage before successive approximation converts that voltage into a 12-bit result. The SPI interface allows sampled measurements to be transferred efficiently between the converter and a digital controller. Key features include 12-bit conversion resolution, eight single-ended input options, and SPI communication. The verified product information identifies four differential input channels, eight single-ended inputs, one SAR conversion engine, and a 2.7 V operating supply. These characteristics make the device useful when an embedded design must monitor multiple sensors, potentiometers, or analog control signals without using a separate ADC for every channel. The MCP3208-BI/P uses the BI temperature grade, which the verified distributor information associates with an operating range of -40°C to +85°C. Its 16-pin PDIP package favors through-hole construction, reworkability, and educational or industrial control boards where a socket or conventional plated through-hole footprint is useful. Because it is a multiplexed converter, the selected channel determines which analog input is connected to the internal sample-and-hold circuit during conversion. Typical applications include industrial process monitoring, environmental sensor acquisition, laboratory measurement interfaces, audio and control-signal digitization, and embedded instrumentation. In these systems, the microcontroller initiates a conversion by writing channel and configuration commands over SPI, waits for the sample-and-hold and conversion sequence, and then reads the 12-bit result. A multiplexed architecture reduces package size, although channel switching means conversions are sequential rather than simultaneous. When designing around the MCP3208-BI/P, verify the analog input range against the selected reference voltage and confirm that the SPI host uses the required clocking and chip-select behavior. Reference and analog-ground routing are critical because ADC accuracy depends on the quality of the voltage reference and the analog signal path. The 16-pin PDIP package also requires adequate through-hole spacing and mechanical clearance in compact production equipment. This product page combines the verified Microchip and distributor specifications with package, application, sourcing, and design context. It also distinguishes verified drop-in replacements from merely similar ADC functions, preventing a functional substitute with a different package from being presented as a PCB-compatible alternative.

RFQ پەیوەندی
MCP3208-BI/SL - 12-Bit 8-Channel SPI ADC | Microchip
MCP3208-BI/SL

MCP3208-BI/SL - 12-Bit 8-Channel SPI ADC | Microchip

The Microchip Technology MCP3208-BI/SL is a 12-bit, 8-channel successive approximation register analog-to-digital converter with a 100 ksps maximum sampling rate, configured for 4 differential or 8 single-ended inputs and housed in a 16-pin SOIC package. It combines an SPI serial interface, programmable input configuration, and low-power operation for embedded control, industrial measurement, and sensor-acquisition systems. An ADC is a data-conversion IC that converts an analog voltage into a digital code for processing, logging, display, or closed-loop control. The MCP3208 belongs to the ADC → data-converter IC → semiconductor hierarchy. Its SAR architecture repeatedly compares the sampled input with an internal reference to produce a 12-bit result. This makes it suitable for adding general-purpose analog measurement to a microcontroller that does not include enough onboard ADC channels. The converter provides eight analog input channels that can be used as eight single-ended inputs or four pseudo-differential input pairs. Maximum differential nonlinearity is ±1 LSB and maximum integral nonlinearity is ±2 LSB for the MCP3208. The SPI interface supports modes 0,0 and 1,1, while the input structure includes an onboard sample-and-hold circuit. These features balance useful conversion resolution with a straightforward host-controller interface. MCP3208-BI/SL operates from a 2.7 V supply, and its analog reference and digital interface support embedded-system integration. The SPI interface transfers the 12-bit conversion result while minimizing pin count compared with a parallel ADC. The 16-SOIC package has a 3.90 mm body width and supports industrial temperature operation from -40°C to +85°C, making it appropriate for compact control boards requiring analog inputs beyond the capabilities of the host MCU. Typical uses include temperature-sensor monitoring, potentiometer position acquisition, current and voltage measurement, industrial panel controls, and multichannel data acquisition. Differential channels can improve rejection of common-mode voltage when paired with suitable sensor circuitry. The 100 ksps rate supports rapidly changing analog signals, although each conversion is initiated and read through the SPI interface. Design the analog and digital sections to minimize noise and ground currents. Place the decoupling and reference components near the converter, route SPI signals away from sensitive analog inputs, and account for reference accuracy when calculating overall measurement error. For battery-powered systems, verify the selected conversion rate and shutdown behavior against the available current budget.

RFQ پەیوەندی
MCP3208-CI/P - 12-Bit 8-Channel SAR ADC | Microchip
MCP3208-CI/P

MCP3208-CI/P - 12-Bit 8-Channel SAR ADC | Microchip

The Microchip Technology MCP3208-CI/P is a 12-bit, eight-channel successive approximation analog-to-digital converter with a 100 ksps sampling rate, 2.7 V to 5.5 V supply range, and SPI interface in a 16-pin PDIP package. It converts four single-ended or eight pseudo-differential analog inputs through programmable input channels, while its sample-and-hold circuitry supports embedded measurement and control systems. An analog-to-digital converter is an ADC, a semiconductor that translates an analog voltage into a digital code. The MCP3208 belongs to the SAR ADC family, using a successive approximation register to acquire one conversion result through successive comparison steps. In the system hierarchy, it is an ADC, data-acquisition IC, embedded-control peripheral, and semiconductor. Key features include 12-bit resolution, eight analog input channels, four pseudo-differential input pairs, a 100 ksps maximum sampling rate, and SPI communication. The manufacturer datasheet describes single-ended or pseudo-differential input programmability, allowing the same device to serve applications with different channel arrangements. Its 2.7 V to 5.5 V operating range supports low-voltage embedded systems and conventional 5 V industrial interfaces. The SAR architecture is appropriate when deterministic sampling, modest resolution, and serial integration are more important than very high throughput. The SPI interface allows a microcontroller to command conversions and read results, while the 16-pin PDIP package supports through-hole prototyping, legacy industrial boards, and designs where a socket or hand-soldered installation is useful. Typical standby and active currents are approximately 500 nA and 320 uA, respectively. Typical applications include industrial process monitoring, environmental sensors, temperature and pressure measurement, laboratory instrumentation, embedded data acquisition, and low-voltage control systems. The SPI bus should be configured for the intended clock and chip-select behavior, and analog inputs must remain within the device's specified voltage limits. For new high-density designs, SOIC variants may be preferable, but the MCP3208-CI/P is specifically the PDIP package. The main design trade-off is throughput and resolution rather than ultra-high precision: 100 ksps and 12-bit resolution are adequate for many control and measurement tasks but may not satisfy demanding instrumentation. This page combines verified Microchip specifications, package information, sourcing references, and application-oriented design guidance.

RFQ پەیوەندی
MCP3208-CI/SL - 12-Bit 8-Ch SAR ADC, SPI, SOIC-16 | Microchip
MCP3208-CI/SL

MCP3208-CI/SL - 12-Bit 8-Ch SAR ADC, SPI, SOIC-16 | Microchip

The Microchip Technology MCP3208-CI/SL is a 12-bit, 8-channel successive approximation register (SAR) analog-to-digital converter (ADC) with an SPI-compatible serial interface, housed in a 16-pin SOIC (SL) package. Operating from a single 2.7V to 5.5V supply, it delivers up to 100 ksps throughput and integrates 8 input channels that can be software-configured as either 8 single-ended inputs or 4 pseudo-differential pairs. An analog-to-digital converter is a mixed-signal integrated circuit that converts a continuous-time, continuous-amplitude voltage on its input pin into a discrete digital code at its output. SAR ADCs in particular use a binary-search algorithm with an internal sample-and-hold and capacitive DAC to converge on the input voltage in N conversion cycles (N = number of bits). SAR converters sit within the broader ADC family alongside delta-sigma (high-resolution, low-speed) and pipeline ADCs (very-high-speed, multi-Msps), and are favored for low-latency, moderate-resolution sampling in embedded systems where determinism and simple serial interfacing matter more than ultimate resolution. Key features include ±1 LSB maximum DNL, ±1 LSB maximum INL, low power consumption of 5 nA standby current and 0.5 mA typical active current at 5V, and an industrial-grade operating temperature range of -40 C to +85 C. The SPI interface uses a standard 4-wire arrangement (CS, DIN, DOUT, CLK), is compatible with 8-bit serial protocols, and supports daisy-chaining of multiple devices on the same bus. The device combines a track-and-hold input stage with a successive-approximation core and on-chip clock. The pseudo-differential input mode provides improved common-mode rejection for bridge sensors and thermocouple interfaces, while single-ended mode maximizes channel count for general-purpose monitoring of 8 separate analog signals. Typical applications include factory automation sensor multiplexing, battery monitoring in portable instruments, data acquisition front-ends for HVAC controllers, and robotics joint position sensing. The SOIC-16 wide-body package simplifies hand-prototyping and is widely accepted by contract assemblers. When designing with the MCP3208, ensure VDD is well-decoupled with a 1 uF ceramic capacitor placed within 5 mm of the AVDD pin, and that the analog input source impedance stays below 1 kohm to avoid converter gain errors. Note that -CI versions are specified over -40 C to +85 C, while -BI versions extend to -40 C to +125 C. This page synthesizes real-time distributor pricing, drop-in alternatives from the same Microchip SAR ADC family, and application notes not collated in the standalone datasheet, helping you evaluate whether MCP3208-CI/SL is the right ADC for your 8-channel embedded design.

RFQ پەیوەندی
MCP3301-BI/MS - 13-Bit Differential SPI ADC | Microchip
MCP3301-BI/MS

MCP3301-BI/MS - 13-Bit Differential SPI ADC | Microchip

The Microchip Technology MCP3301-BI/MS is a 13-bit successive-approximation analog-to-digital converter with one fully differential input channel, a 100 ksps conversion rate, and an SPI-compatible serial interface. It operates from a single 5.5 V supply and is packaged in an 8-MSOP for compact analog measurement systems. The -BI/MS ordering identifies the industrial temperature grade and MSOP package format used in the MCP3301 family. An analog-to-digital converter is an integrated circuit that converts a continuous voltage at an analog input into a numeric code for processing, control, display, or data logging. The MCP3301 belongs to the SAR ADC hierarchy, where a sample-and-hold circuit and internal comparator successively resolve the input voltage. Its differential architecture measures the voltage between the AIN0+ and AIN0- pins, which helps reject common-mode noise when the sensor output is referenced to a shared ground. Key device characteristics include 13-bit resolution, a maximum conversion throughput of 100 ksps, full differential input capability, an SPI serial interface, and single-supply operation from a 5.5 V maximum supply. The datasheet also specifies differential nonlinearity and integral nonlinearity limits of plus or minus 1 LSB for the MCP3301 grade. Its compact 8-MSOP footprint suits battery-powered instruments and remote data-acquisition nodes where board area and standby power are important. The conversion core uses a sample-and-hold architecture, while the serial interface supports serial input and output functions on shared clock and data pins. The device accepts an external reference voltage, allowing measurement accuracy to be scaled to the analog signal chain. Because the MCP3301 has one differential channel rather than multiple single-ended inputs, channel multiplexing is not required, and differential source impedance should remain balanced for best performance. Typical applications include battery-powered environmental sensors, industrial pressure and temperature transmitters, remote process-monitoring nodes, laboratory measurement instruments, and low-power data loggers. The SPI interface makes the converter suitable for designs using a microcontroller with a dedicated or general-purpose serial controller. The main design consideration is the relationship between reference accuracy, source impedance, and digital noise coupling. Place the reference and analog input traces away from high-current switching paths, use a quiet reference source, and follow the manufacturer datasheet layout and bypass recommendations. Verify acquisition timing in firmware because each conversion requires a sample period followed by bit transfer over the serial interface. This page combines the Microchip product information and datasheet with package details, purchasing guidance, comparison parameters, and practical integration notes that help engineers evaluate the MCP3301-BI/MS for low-power precision measurement designs.

RFQ پەیوەندی
MCP3301-BI/P - 13-Bit 100 kSPS SPI ADC | Microchip Technology
MCP3301-BI/P

MCP3301-BI/P - 13-Bit 100 kSPS SPI ADC | Microchip Technology

The Microchip Technology MCP3301-BI/P is a 13-bit, single-channel SAR analog-to-digital converter with one differential input, a 100 kSPS conversion rate, and an SPI serial interface in an 8-pin PDIP package. It operates from a 4.5 V to 5.5 V single supply and is specified over -40°C to +85°C. An ADC is an analog-to-digital converter, a semiconductor that samples a continuous voltage and converts it into a numerical value for processing by a microcontroller or other digital controller. The MCP3301 belongs to the SAR ADC, ADC, data-converter IC, and power-management-adjacent signal-conversion hierarchy. Its fully differential input can reject common-mode noise when the source is arranged around a biased reference voltage. Key features include 13-bit resolution, a 100 kSPS maximum sampling rate, and ±1 LSB maximum differential nonlinearity. The B-grade MCP3301-BI/P has a maximum integral nonlinearity of ±2 LSB. Its SPI interface provides a straightforward connection to embedded processors, while single-supply operation simplifies system power planning for industrial, battery-powered, and remote data-acquisition equipment. The device uses a successive-approximation conversion architecture. Each conversion determines the unknown input through a sequence of internal comparisons, after which the result is transferred through the serial interface. The differential input architecture is useful when the measured signal is small relative to the ADC supply. Biasing both inputs near the midpoint of the input range improves use of the available code range, while keeping their differential voltage within the converter's permitted input range. Typical applications include battery-powered environmental sensors, industrial pressure or temperature acquisition, remote monitoring, laboratory measurement equipment, and embedded control systems. The 100 kSPS rate is suitable for continuously changing analog measurements that do not require high-rate waveform capture, and the differential input can simplify front-end design for bridge sensors and small-signal transducers. Designers should provide a stable reference voltage, bypass the supply close to the device, and maintain the analog input voltage within the operating range. The SPI clock, chip-select, and digital output timing must satisfy the manufacturer datasheet, and unused input and reference pins must be connected according to its recommended application circuit. This page consolidates verified manufacturer and distributor information, package-level alternatives, interface guidance, and application-specific selection context. It is intended to help engineers locate the datasheet, compare interchangeable variants, plan a PCB layout, and assess whether the MCP3301-BI/P fits a precision, low-power measurement design.

RFQ پەیوەندی
MCP3301-CI/P - 13-Bit 100ksps Diff ADC with SPI | Microchip
MCP3301-CI/P

MCP3301-CI/P - 13-Bit 100ksps Diff ADC with SPI | Microchip

The Microchip Technology MCP3301-CI/P is a 13-bit differential-input, low-power successive-approximation-register (SAR) analog-to-digital converter (ADC) with an industry-standard SPI serial interface, housed in an 8-pin PDIP through-hole package. The converter achieves up to 100 ksps sampling rate over a 4.5V to 5.5V single supply, with differential inputs that allow the full-scale input range to be referenced to a user-supplied voltage between 400 mV and 5V, yielding an input-referred resolution range between approximately 98 uV (at 0.4V VREF) and 1.22 mV (at 5V VREF). An SAR ADC is a successive-approximation-register analog-to-digital converter, the dominant topology for medium-speed, medium-resolution precision conversion in microcontroller-based systems. SAR ADCs sit within the broader ADC taxonomy (Flash, SAR, Delta-Sigma, Dual-Slope) and are preferred where deterministic latency, low power consumption, and ease of microcontroller interface are required - exactly the trade-off space the MCP3301 targets. Key features include true differential inputs with low integral nonlinearity, an external VREF input that scales input range dynamically, an SPI-compatible serial output that simplifies connection to virtually any microcontroller, and very low power consumption - typically 50 nA standby and 300 uA active. The 8-pin PDIP through-hole format supports easy prototyping, breadboarding, and legacy industrial designs where surface-mount is undesirable. Architecturally, the MCP3301 combines a differential input sample-and-hold front-end, a precision SAR core clocked from an internal oscillator, and a discrete SPI output shift register. The combination produces one conversion per chip-select cycle, deterministic sampling instant, and intrinsic single-cycle latency - ideal for multiplexed sensor arrays and digital control loops. Typical applications include battery-powered remote sensor nodes, industrial process control loops, portable instrumentation, multi-channel thermocouple or load-cell digitizers (paired with external multiplexers), and embedded data-acquisition front-ends for HVAC and energy-metering systems. When designing with this part, remember to include a 0.1 uF decoupling capacitor close to the AVDD pin and to keep CS low during a full 13-clock conversion - releasing CS mid-frame will corrupt the output. The external VREF source must be low-noise to fully benefit from the 13-bit resolution. This page synthesizes distributor pricing, drop-in PDIP alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
MCP3301-CI/SN - 13-Bit Low-Power SPI ADC | Microchip Technology
MCP3301-CI/SN

MCP3301-CI/SN - 13-Bit Low-Power SPI ADC | Microchip Technology

The Microchip Technology MCP3301-CI/SN is a 13-bit, one-channel, differential-input successive-approximation analog-to-digital converter with an SPI serial interface, conversion rate up to 100 ksps, and an 8-pin SOIC package. Its low active current of 300 µA and standby current of 50 nA make it suitable for battery-powered instrumentation and remote data-acquisition systems. An analog-to-digital converter is an interface IC that converts a continuous analog voltage into a numeric value for processing, storage, or transmission. The MCP3301 belongs to the successive-approximation ADC hierarchy, which repeatedly compares the input against an internal DAC until its output matches the analog voltage. A differential ADC measures the voltage between two inputs, allowing common-mode voltage to be rejected when the source is balanced around a common return or reference. The converter supports a 4.5 V to 5.5 V supply range and can perform conversions at up to 100 ksps. Its reference voltage can be varied from 400 mV to 5 V. As a result, the input-referred resolution ranges from 98 µV with a 400 mV reference to 1.22 mV with a 5 V reference. The ±1 LSB maximum differential nonlinearity and ±2 LSB maximum integral nonlinearity identified for the -C version characterize the converter’s transfer accuracy. The SPI interface provides a familiar connection to microcontrollers, and the converter can remain in a low-current standby state between measurements. The single differential channel is appropriate for bridge sensors, current-shunt measurements, battery monitoring, temperature sensing, and other systems where preserving signal polarity and rejecting common-mode disturbance are important. The small 8-pin SOIC package also simplifies compact analog acquisition boards. Typical uses include low-power environmental sensors, industrial pressure and temperature acquisition, portable instrumentation, remote telemetry, and precision analog measurement. The 100 ksps rate supports faster measurement loops than a low-speed meter-oriented ADC while retaining the simplicity of a one-channel converter. Designers should select the reference and input ranges carefully because the usable differential voltage must remain within the reference-defined conversion range. Input and reference routing should be short and symmetric to minimize conversion error and noise pickup. When the source is not differential, a suitable signal-conditioning circuit may be required to translate its output into the converter’s differential input range. This product page combines the manufacturer’s operating limits, conversion characteristics, pin assignment, application guidance, package details, and same-footprint family options to support faster component selection and PCB planning.

RFQ پەیوەندی
MCP3301T-BI/MS - 13-Bit Differential SAR ADC | Microchip
MCP3301T-BI/MS

MCP3301T-BI/MS - 13-Bit Differential SAR ADC | Microchip

Microchip Technology MCP3301T-BI/MS is a 13-bit successive-approximation analog-to-digital converter with one fully differential input, a 100 kHz conversion rate, and an 8-lead MSOP package. It operates from a 4.5 V to 5.5 V supply, supports an SPI interface, and is specified for industrial temperatures from -40 °C to +85 °C. The device provides a 50 nA typical input leakage current and approximately 78 dB signal-to-noise performance, making it suitable for precision analog measurement systems. An ADC converts a continuous analog voltage into a numeric code for processing, storage, or control. The MCP3301 belongs to the SAR ADC family, which compares the sampled input against an internal reference during successive conversion cycles. Its differential input architecture rejects common-mode noise and allows one signal to be measured relative to another rather than relative to ground. The result is a compact data-acquisition IC for battery-powered instruments, industrial sensors, and remote monitoring systems. Key characteristics include 13-bit resolution, one differential input channel, a 100 kHz maximum sampling rate, and an SPI serial interface with an external clock option. The manufacturer identifies a 1.7 MHz external clock capability, while the listed frequency range of 85 kHz to 1.7 MHz reflects the supported operating modes. Low 50 nA input leakage helps preserve the accuracy of high-impedance sensor networks, while approximately 78 dB SNR supports accurate acquisition of slowly changing or moderate-bandwidth signals. The SAR conversion architecture provides predictable sampling behavior and effective linearity without requiring the continuous internal clocking associated with delta-sigma converters. Digital results are transferred through the serial interface, reducing the number of package pins required for data transport. Because this is a single-channel converter, applications requiring simultaneous measurements need multiplexing ahead of the ADC or a multichannel converter family. Typical uses include industrial process monitoring, battery-powered data loggers, environmental sensors, portable measurement instruments, and remote acquisition nodes. The differential input is particularly useful when the sensor output is small, noisy, or referenced to another voltage. The 8-lead MSOP footprint also supports compact analog front ends where board area is constrained. For reliable operation, place the decoupling capacitor directly between the supply and ground pins, route analog and digital returns thoughtfully, and keep the analog input traces short and away from SPI switching edges. A stable reference source is essential because reference error directly limits absolute conversion accuracy. Confirm input range, acquisition timing, and available clock frequency against the manufacturer datasheet before finalizing signal-chain headroom and filtering. This page combines the manufacturer product information, distributor technical listings, package details, and application-focused design guidance to support faster component selection, PCB planning, and signal-chain design for the MCP3301T-BI/MS.

RFQ پەیوەندی
MCP3301T-BI/SN - 13-Bit Differential SAR ADC | Microchip
MCP3301T-BI/SN

MCP3301T-BI/SN - 13-Bit Differential SAR ADC | Microchip

The Microchip Technology MCP3301T-BI/SN is a 13-bit, single-channel, differential-input successive-approximation analog-to-digital converter in an 8-pin SOIC package. It combines a full-differential input architecture with an SPI-compatible serial interface and low-power operation for battery-powered instrumentation and remote data-acquisition systems. The tape-and-reel ordering code is designed for automated production assembly. An analog-to-digital converter, or ADC, converts an analog voltage into a numeric value for processing by a microcontroller or other digital controller. The MCP3301 belongs to the ADC and DAC category within the broader semiconductor and data-converter hierarchy. Its differential input is useful when the source has a centered or shifting reference point and a dedicated VREF+ and VREF- connection supports common-mode input-range control. The MCP3301 uses successive-approximation conversion and provides 13-bit resolution. This resolution supports 8,193 distinct numerical codes across an ideal 13-bit transfer function. The single-channel architecture reduces analog routing requirements compared with a multiplexed converter, while the SPI serial interface allows a host processor to obtain conversion results using a compact command-and-data sequence. Low power consumption is a defining feature of the MCP3301, making it suitable for portable measurement systems where every milliamp of average demand can shorten operating time between battery replacements. The manufacturer identifies the device for battery-powered systems and remote data acquisition. Its 8-SOIC package is compact, widely supported by PCB assembly equipment, and suitable for prototypes as well as production circuits. Typical applications include battery-powered environmental monitoring, precision control systems, laboratory measurement equipment, industrial sensor interfaces, portable instrumentation, and remote telemetry nodes. In these systems, the converter can digitize a differential sensor output and present the result to a microcontroller through its serial interface, reducing analog cabling requirements and making the measurement path less susceptible to common-mode interference. When designing around the MCP3301T-BI/SN, establish the reference voltage and analog input range before selecting gain and sensor excitation. Keep the reference and analog traces compact, route them away from fast switching nodes, and use a quiet ground reference to maximize conversion accuracy. The SPI clock and digital-control traces should remain short enough to prevent timing or signal-integrity problems at the system clock. This product overview combines the manufacturer feature description, ordering information, package details, and practical guidance for battery-powered and remote data-acquisition designs. It also distinguishes the available family alternative and explains when its standard package configuration is preferable to the tape-and-reel production ordering code.

RFQ پەیوەندی
MCP3301T-CI/MS - 13-Bit SPI ADC | Microchip Technology
MCP3301T-CI/MS

MCP3301T-CI/MS - 13-Bit SPI ADC | Microchip Technology

The Microchip Technology MCP3301T-CI/MS is a 13-bit, single-channel successive-approximation analog-to-digital converter with a fully differential input, operating from a 2.7 V to 5.5 V supply and communicating through an SPI-compatible serial interface. It is packaged in an 8-pin MSOP with a nominal operating temperature range of -40 °C to +85 °C. The MCP3301 family combines low power consumption with a compact package for battery-powered systems and remote data-acquisition equipment. An ADC is a mixed-signal semiconductor that converts an analog voltage into a digital code for processing, measurement, storage, or control. The MCP3301 belongs to the SAR ADC hierarchy, where a successive-approximation conversion produces one output bit during each comparison cycle. Its differential input accepts a voltage difference between two analog nodes rather than measuring a single input relative to ground. This architecture is useful when the signal source is balanced, when noise common to both input nodes should be rejected, or when a current-sense or bridge circuit must be measured around a midpoint. Key features include 13-bit resolution, one differential analog-input channel, SPI-compatible communication, low-power operation, and an 8-MSOP package. The converter supports both single-ended and differential measurements, allowing the same device to serve compact sensing systems, temperature probes, pressure transducers, potentiometers, and other analog front ends. Its small package and low power consumption are especially valuable in remote sensors and portable instruments where board area and energy budget are tightly constrained. The MCP3301 uses a sample-and-hold architecture and an internal reference arrangement selected through the serial interface. During conversion, the SAR logic compares the sampled input against an internally generated DAC value. The resulting code is shifted out through the serial data output, while chip select and clock signals coordinate the transaction with the host controller. The SPI interface simplifies connection to microcontrollers while allowing the ADC to share a controlled bus with other compatible peripherals. Typical applications include battery-powered environmental monitors, industrial remote sensing nodes, laboratory measurement instruments, process-control equipment, and low-energy data loggers. The differential input can be connected to bridge sensors or differential signal sources, while a grounded input arrangement can be used where a single-ended source is more convenient. Designers should preserve a quiet analog ground and place input and reference components close to the device to minimize pickup and conversion error. For a new design, first confirm the analog input range, reference arrangement, conversion timing, and SPI mode against the manufacturer datasheet. Pay particular attention to source impedance and acquisition time: the sampling network must charge the internal sample-and-hold capacitor sufficiently before conversion. This page also organizes package information, practical design guidance, sourcing questions, and qualified drop-in alternatives for faster component evaluation.

RFQ پەیوەندی
MCP3301T-CI/SN - 13-Bit 100 ksps Differential ADC | Microchip
MCP3301T-CI/SN

MCP3301T-CI/SN - 13-Bit 100 ksps Differential ADC | Microchip

The Microchip Technology MCP3301T-CI/SN is a 13-bit, single-channel, successive-approximation analog-to-digital converter with a fully differential input, an SPI serial interface, and a low-power design suitable for battery-powered and remote data-acquisition systems. It converts at up to 100 ksps, operates from a 4.5 V to 5.5 V supply, and accepts an external reference voltage from 400 mV to 5 V. The device is packaged in an 8-pin SOIC configuration. An ADC is an analog-to-digital converter, a semiconductor that samples a continuous voltage and produces a corresponding digital code. The MCP3301 belongs to the data-converter IC hierarchy and specifically provides one differential input with 13-bit resolution. Differential operation means that the converter measures the voltage between two input nodes rather than measuring a single input relative to ground. This architecture is useful when the signal source is balanced or when common-mode noise must be rejected. Key specifications include 13-bit resolution, a maximum conversion rate of 100 ksps, and a 4.5 V to 5.5 V supply range. The external reference can vary from 400 mV to 5 V, producing input-referred resolution between 98 µV and 1.22 mV. The SPI interface supports straightforward communication with microcontrollers, while the low-power characteristics suit portable instruments and distributed sensing nodes. Internally, the MCP3301 uses a successive-approximation conversion process, charging an internal sample-and-hold capacitor before comparing the sampled voltage against its reference. The external reference defines the input range and therefore affects both conversion accuracy and code scaling. Designers must account for reference noise, input-source impedance, acquisition time, and SPI clock timing when interpreting the rated throughput. Typical uses include battery-powered measurement equipment, industrial process monitoring, remote data acquisition, environmental sensors, and laboratory instruments. A differential sensor, current-sense amplifier, or low-level transducer can feed the ADC when its output voltage remains within the selected reference range. The converter is particularly appropriate where one analog channel is sufficient and low power consumption is more important than high channel count. Place the reference and input networks close to the device, keep analog traces short, and provide a quiet reference source. Because the MCP3301 requires an external reference, reference stability can dominate the overall measurement accuracy. The 8-pin SOIC footprint simplifies assembly, but careful grounding and decoupling remain necessary to preserve the converter's low-noise performance. This product page combines the core electrical characteristics, application guidance, comparison information, and practical design considerations needed to evaluate the MCP3301T-CI/SN for an SPI-based analog measurement design.

RFQ پەیوەندی
MCP3302-BI/P - 13-Bit SPI ADC, 100 ksps, 14-PDIP | Microchip Technology
MCP3302-BI/P

MCP3302-BI/P - 13-Bit SPI ADC, 100 ksps, 14-PDIP | Microchip Technology

The Microchip Technology MCP3302-BI/P is a 13-bit successive-approximation (SAR) analog-to-digital converter with four single-ended / two fully differential inputs, a 100 ksps conversion rate and an industry-standard SPI serial interface, packaged in a 14-pin PDIP (PDIP-14) tube. It offers 12-bit plus sign resolution, differential input capability and low power consumption for battery-powered systems and remote data acquisition. An SAR ADC is a category of data-conversion IC that converts an analog voltage into a digital code by comparing the input against a capacitor DAC and successively refining a binary approximation through a comparator. In the broader hierarchy, an ADC is a data converter, which is a data acquisition building block, which sits inside a mixed-signal signal-chain IC alongside op amps, references and interfaces. SAR converters trade resolution-per-conversion speed for very low power and low cost, making them the default choice for slow sensor signals rather than high-bandwidth waveform capture. Key features of the MCP3302-BI/P include true differential analog inputs, an SPI interface with chip select, serial data input and clock pins that can run from a simple microcontroller, low standby current for portable instruments, and a 14-pin PDIP package that is easy to prototype and hand-solder. The -BI/P ordering code designates the 13-bit, industrial-temperature PDIP variant supplied in tubes. Technically, the device uses a sample-and-hold front end ahead of the SAR conversion core, so the input is frozen during each conversion cycle. Multiple inputs are multiplexed, meaning only one analog node is connected to the internal DAC and comparator at a time. The differential architecture means the converter measures V(+) minus V(-), which rejects common-mode noise if the two wires are routed as a differential pair. Typical applications include battery-powered environmental monitoring, precision temperature and pressure sensor acquisition with thermocouple or ratiometric bridges, industrial 4-20 mA loop receivers, and low-rate energy metering. Companion silicon commonly includes SPI-capable microcontrollers such as ATMEGA328P-MNR, RS-485 transceivers such as SP490CN-L/TR for remote field buses, and digital I/O expanders such as PCA9554DBR. A key design consideration is the reference voltage: accuracy of the converted code is bounded by the stability and noise of the VREF pin, so a clean, decoupled reference and adequate input filtering are mandatory for accurate results. The MCP3302-BI/P is a 14-pin PDIP, so newer designs may prefer the SOIC-14 variant. This page combines verified distributor listings, a drop-in replacement review, and practical design notes that go beyond the manufacturer datasheet summary, including interface timing notes, filtering guidance and part-to-part trade-offs.

RFQ پەیوەندی
MCP3302-BI/SL - 13-Bit 2-Channel SAR ADC | Microchip
MCP3302-BI/SL

MCP3302-BI/SL - 13-Bit 2-Channel SAR ADC | Microchip

Microchip Technology MCP3302-BI/SL is a 13-bit analog-to-digital converter with two differential input channels, four single-ended inputs, one SAR conversion engine, and an SPI serial interface in a 14-pin SOIC package. It is designed for compact, low-power measurement systems where differential sensing improves signal integrity and common-mode rejection. An ADC converts an analog voltage into a numeric value for processing, measurement, logging, or control. The MCP3302 belongs to the successive-approximation-register, or SAR, ADC family. Its SAR architecture compares the input against an internal DAC through successive conversion steps, providing predictable sampling behavior suitable for instrumentation and embedded data-acquisition systems. The MCP3302-BI/SL provides 13-bit resolution, two differential or four single-ended input choices, and one SAR converter. Its SPI interface supports connection to microcontrollers and other digital controllers. Full differential inputs are especially useful when the measured source sits around a nonzero reference voltage or when ground offsets and coupled noise could affect single-ended measurements. The device is aimed at battery-powered systems and remote data-acquisition equipment, according to the manufacturer product page. Its low-power operating approach helps limit energy use in portable instruments, while the 14-pin SOIC package supports conventional surface-mount assembly. The BI ordering code and SL package code identify the exact commercial variant represented by MCP3302-BI/SL. Typical uses include battery monitors, current and voltage measurements, temperature sensing, industrial process measurement, portable instrumentation, and remote sensor acquisition. Differential pairing is useful for ratiometric sensor measurements, bridge outputs, and amplified sensor signals where rejecting common-mode disturbance is important. The SPI interface also allows the ADC to be shared with other compatible peripherals on a controller bus. Design the reference, analog input, and digital interfaces carefully. Keep analog and return paths short, provide stable reference bypassing, and use an appropriate common-mode range and source impedance for the selected channel configuration. Confirm conversion timing, input capacitance, and operating limits against the manufacturer datasheet before establishing system timing or scaling sensor output. This product page combines the manufacturer product description with verified distributor identification, packaging information, application guidance, and drop-in alternatives. It is intended to help engineers evaluate ADC architecture, pin compatibility, interface requirements, and design constraints before embedding the MCP3302-BI/SL in a PCB design.

RFQ پەیوەندی
MCP3302-BI/ST - 13-Bit Dual-Channel SPI ADC | Microchip
MCP3302-BI/ST

MCP3302-BI/ST - 13-Bit Dual-Channel SPI ADC | Microchip

The Microchip Technology MCP3302-BI/ST is a 13-bit, dual-channel successive-approximation analog-to-digital converter with two differential or four single-ended inputs, a 100 kSPS sampling rate, and an SPI serial interface. It is packaged in a 14-pin TSSOP for compact, surface-mount data-acquisition and embedded-control designs. An ADC is a data-acquisition IC that converts an analog voltage into a digital code for processing by a microcontroller or other digital controller. The MCP3302 belongs to the ADC > data-converter > data-acquisition IC hierarchy and supports precision measurement in battery-powered systems, industrial equipment, remote sensors, and test instruments. Its differential inputs are particularly useful when the source is a bridge sensor or another circuit centered around a biased reference voltage. The MCP3302-BI/ST provides 13-bit conversion resolution, two differential or four single-ended input channels, and a maximum sampling rate of 100 kSPS. The SPI interface supports communication with a host processor, while the operating-temperature range of -40°C to +85°C suits industrial equipment. The 14-TSSOP package also allows reuse of a compact mixed-signal PCB layout where analog conversion must coexist with digital control circuitry. The device uses a successive-approximation conversion architecture, meaning the internal converter determines each result through a sequence of increasingly accurate bit decisions. Its low-power design is appropriate for portable and remote data-acquisition systems. Differential sampling can improve common-mode rejection when the measured signal is small and appears in the presence of process noise, although front-end conditioning remains necessary to keep the input voltage within the converter’s valid range. Typical uses include measuring pressure, temperature, strain, potentiometer positions, and other slowly changing analog signals. It can also serve industrial control modules, battery-powered environmental monitors, laboratory measurement equipment, and remote telemetry systems. For multiplexed sensors, separate analog switches may be required because the target configuration provides two differential or four single-ended channels. Design the reference-voltage and analog-input network carefully. Keep SPI traces short, provide a clean supply path, decouple the supply and reference pins near the IC, and route analog inputs away from switching nodes. Confirm input range, acquisition timing, and digital logic levels against the manufacturer datasheet before finalizing the schematic and PCB layout. This product page combines the manufacturer’s device description with practical selection criteria, compatible alternatives, interface considerations, and design guidance to support faster engineering evaluation and more accurate PCB planning.

RFQ پەیوەندی
MCP3302-CI/P - 13-Bit Differential ADC | Microchip Technology
MCP3302-CI/P

MCP3302-CI/P - 13-Bit Differential ADC | Microchip Technology

The Microchip Technology MCP3302-CI/P is a 13-bit successive-approximation analog-to-digital converter with 2 differential channels, 4 input connections, and an SPI serial interface, housed in a 14-pin PDIP package. It combines full differential input support with low power consumption, making it suitable for battery-powered systems, remote data acquisition, and other applications that require compact, serial-output conversion. An ADC converts an analog voltage into a digital value for processing, measurement, or storage. The MCP3302 belongs to the ADC hierarchy, where a successive-approximation register compares the unknown input against internally generated reference voltages until the converted code is available. Its differential architecture supports measurement of voltage differences between input pairs, which can improve common-mode rejection when the source is carefully interfaced and the analog front end is designed accordingly. Key features include a 13-bit conversion resolution, two differential ADC channels, four input connections, full differential inputs, and an SPI-compatible serial interface. The SPI interface is suitable for connecting the converter to a microcontroller or other digital controller while transferring conversion results over a compact serial link. The low-power operating characteristics are particularly relevant for remote and battery-powered installations where reducing energy use can extend operating time. Technically, the MCP3302 uses a successive-approximation conversion architecture and offers a two-channel differential ADC. Microchip positions the device for low-power, small-package implementations where the complete measurement chain must communicate with a host processor. Because the MCP3302-CI/P is supplied in a 14-pin PDIP package, it is more appropriate for through-hole assembly and legacy-style PCB layouts than for space-constrained surface-mount designs. Typical applications include battery-powered environmental monitors, remote sensor acquisition nodes, industrial process measurement, laboratory instrumentation, and embedded control systems. The differential inputs can support bridge or ratiometric sensing when paired with suitable input conditioning, while SPI permits straightforward connection to a host microcontroller. Designers should verify the reference voltage, analog input range, sampling rate, digital interface timing, and acquisition method against the manufacturer datasheet before finalizing signal-chain and firmware requirements. Reference routing, source impedance, grounding, and differential pairing are as important as the converter itself when achieving repeatable measurements.

RFQ پەیوەندی
MCP3302-CI/SL - 13-Bit Dual-Channel ADC | Microchip
MCP3302-CI/SL

MCP3302-CI/SL - 13-Bit Dual-Channel ADC | Microchip

The Microchip Technology MCP3302-CI/SL is a 13-bit successive-approximation analog-to-digital converter with two differential or four single-ended inputs, a maximum conversion rate of 100 ksps, and an SPI serial interface in a 14-pin SOIC package. It is designed for low-power battery-powered systems, remote data acquisition, and precision analog measurement. An ADC is a data-acquisition IC that converts an analog voltage into a digital value for processing, measurement, logging, or control. The MCP3302 belongs to the successive-approximation ADC hierarchy, where an internal sample-and-hold circuit and successive comparison process each input. It is a low-power analog-to-digital converter within the broader ADC and data-conversion IC category. Key features include 13-bit resolution, 100 ksps conversion throughput, two differential or four single-ended input configurations, and a single-supply operating point of 5.5 V. Differential inputs support rejection of common-mode voltage and measurement of small signals placed between two input nodes, while the single-ended configuration can use four channels referenced to ground. The -C grade provides maximum differential nonlinearity and integral nonlinearity values of ±1 LSB and ±2 LSB, respectively. These characteristics describe how closely the converter's transfer function follows an ideal straight line. The MCP3302T-CI/SL variant uses the same converter in a tape-and-reel ordering configuration, while MCP3302-CI/SL is supplied in the non-tape-and-reel configuration. Typical uses include battery-powered environmental monitoring, remote sensor acquisition, industrial process measurement, laboratory instrumentation, and low-speed precision control. Differential measurements are especially useful for bridge sensors and current-sense systems where a signal is expressed between two analog nodes rather than relative to ground. When designing around this ADC, place input and reference-decoupling capacitors close to their pins, keep analog and digital return currents separate, and use a stable reference source when measurement accuracy matters. The SPI interface simplifies connection to microcontrollers, but software must correctly handle conversion timing and the device's input-code format. This product page combines the manufacturer information with practical acquisition guidance, drop-in family comparisons, pin-package constraints, and design notes for engineers evaluating the MCP3302-CI/SL in low-power precision ADC applications.

RFQ پەیوەندی
MCP3302-CI/ST - 13-Bit Differential ADC | Microchip
MCP3302-CI/ST

MCP3302-CI/ST - 13-Bit Differential ADC | Microchip

The Microchip Technology MCP3302-CI/ST is a 13-bit, two-channel differential-input analog-to-digital converter with an SPI serial interface, 100 ksps conversion capability, and a 14-pin TSSOP package. It combines a compact surface-mount format with low-power operation for battery-powered systems, remote data acquisition, and precision analog measurement designs. An analog-to-digital converter, or ADC, converts continuously varying analog voltages into numeric values that a microcontroller, digital signal processor, or data-acquisition system can process. The MCP3302 belongs to the SAR ADC family, where successive approximation rapidly determines the digital code associated with an input voltage. Its two differential input channels can measure the voltage difference between paired sensor or signal nodes, which helps reject common-mode noise when the two inputs share a similar reference potential. The MCP3302-CI/ST provides a 13-bit conversion resolution and a 100 ksps maximum sampling capability. Its two-channel architecture makes it suitable for redundant sensing, bridge excitation, current measurement, and dual-channel instrumentation. The SPI interface supports straightforward connection to embedded controllers, while the differential-input structure is useful when signal integrity and common-mode rejection are more important than maximum channel count. Microchip identifies the device as a low-power ADC intended for battery-powered and remote acquisition equipment. Low-power operation is valuable in these systems because the energy consumed during repeated conversions can dominate the operating budget. Designers should still evaluate the complete acquisition path, including the input amplifier, reference source, sampling network, controller activity, and idle intervals, rather than considering converter consumption alone. Typical applications include industrial sensor acquisition, battery-powered environmental monitors, portable measurement instruments, current sensing, and low-speed closed-loop control. Differential input operation is particularly useful when a sensor produces a small signal riding on a larger common-mode voltage. The design must still ensure that every applied input remains within the ADC's absolute maximum and analog operating limits. Layout and signal-conditioning decisions are central to achieving useful resolution. Place input and reference decoupling close to their pins, use a quiet reference source, and route high-impedance input traces away from digital and switching nodes. The input source impedance should be considered during acquisition timing, and the 14-pin TSSOP footprint requires careful fanout and assembly planning. This page organizes the available manufacturer and distributor information around the MCP3302-CI/ST's key design facts. It also identifies where a replacement search is needed, since the cross-reference results do not establish any additional pin-compatible ADC without independent verification of its pinout and electrical behavior.

RFQ پەیوەندی
MCP3302T-BI/SL - 13-Bit Dual-Channel ADC | Microchip
MCP3302T-BI/SL

MCP3302T-BI/SL - 13-Bit Dual-Channel ADC | Microchip

The Microchip Technology MCP3302T-BI/SL is a 13-bit, dual-channel successive-approximation analog-to-digital converter with four differential or single-ended inputs, a 100 kSPS conversion rate, and an SPI serial interface in a 14-pin SOIC package. It operates from a 4.5 V to 5.5 V supply, making it suitable for precision industrial instrumentation, sensor acquisition, and low-power embedded measurement systems. An ADC is a semiconductor that converts an analog voltage into a digital number for processing by a microcontroller or other digital system. The MCP3302 belongs to the successive-approximation ADC hierarchy, which uses an internal sample-and-hold circuit, comparator, and successive conversion process. Its differential inputs support measurement of voltage differences, while the SPI interface allows a host processor to retrieve conversion results through a compact, serial connection. Key features include 13-bit resolution, two simultaneous-looking analog input channels, four selectable analog inputs, 100 kSPS sampling performance, and a 4.5 V to 5.5 V analog supply range. The four-input architecture allows two channels to be configured as differential inputs or as four single-ended channels. This flexibility supports bridge sensors, ratiometric measurements, potentiometer sensing, and multiple analog signals sharing one converter. The MCP3302 uses a serial peripheral interface compatible with the industry-standard SPI framing used by Microchip's related MCP3301 family. A microcontroller can issue a conversion command, wait for the indicated conversion interval, and read the 13-bit result through the serial data and clock lines. Differential operation reduces common-mode sensitivity when the measured signal is small relative to the voltage referenced by the converter. Typical applications include industrial process-control modules, battery-powered remote sensors, laboratory measurement equipment, environmental monitors, and compact control boards. The low-power operating environment and small SOIC footprint are useful where board area and energy use are constrained. Designers should also account for analog-reference quality, input settling time, source impedance, and PCB layout when establishing conversion accuracy. For reliable operation, bypass the analog supply close to the device and route analog and digital return currents separately. Reference and signal traces should remain short, with analog ground arranged to minimize voltage drops caused by digital output currents. Input-driver settling must be checked against the converter's sampling network, especially when multiplexed sensors have high output impedance. This product page combines the manufacturer specifications, verified distributor listings, package information, replacement analysis, and application-focused engineering guidance. It also distinguishes a true pin-compatible alternative from broader functional ADC options, helping designers evaluate PCB reuse, interface continuity, resolution, conversion rate, and supply requirements before approving a substitution.

RFQ پەیوەندی
MCP3302T-BI/ST - 13-Bit Dual SAR ADC | Microchip
MCP3302T-BI/ST

MCP3302T-BI/ST - 13-Bit Dual SAR ADC | Microchip

The Microchip Technology MCP3302T-BI/ST is a 13-bit, two-channel successive-approximation analog-to-digital converter with four analog input options and differential input capability, housed in a 14-pin TSSOP package. It uses the industry-standard SPI serial interface and is designed for low-power, compact data-acquisition systems. An analog-to-digital converter, or ADC, converts continuously varying analog voltages into numerical values that a microcontroller or other digital controller can process. The MCP3302 belongs to the ADC and data-acquisition hierarchy, where its SAR architecture repeatedly compares the input voltage with a generated reference level. Differential inputs support measurement of voltage differences, while the low-power architecture is useful in battery-powered instrumentation and remote sensing systems. The MCP3302T-BI/ST provides 13-bit resolution, two conversion channels, and selectable single-ended or differential operation. Its 14-pin TSSOP package supports compact PCB layouts while exposing four analog inputs through the device's multiplexed input architecture. The SPI interface simplifies connection to microcontrollers and reduces the number of signal lines required for transferring converted results. Because this converter uses SAR conversion, it is suited to applications that need direct, deterministic digitizing of slowly changing or sampled analog signals. The MCP3302 family is positioned for remote data acquisition, battery-powered systems, industrial measurement, and embedded control rather than high-speed waveform capture. Its multiplexing architecture allows several analog sources to share a compact converter footprint. Typical applications include sensing potentiometer positions, monitoring thermistor or resistive sensor networks, acquiring pressure or flow transducer signals, reading differential sensor outputs, and digitizing control inputs in embedded systems. Differential measurement can improve rejection of common-mode noise when the sensor output is centered around a biased reference voltage. Designers should follow the manufacturer pin-description table when assigning analog, reference, ground, and SPI connections. Reference and analog decoupling should be placed close to the corresponding pins, and the analog return path should remain separated from noisy digital switching paths. Validate the complete input range, reference voltage, sample timing, and channel-selection sequence against the system acquisition requirements. This page combines the manufacturer product description, verified distributor listings, package details, replacement guidance, comparison parameters, and practical PCB design considerations to support faster component selection and implementation.

RFQ پەیوەندی
MCP3302T-CI/SL - 13-Bit 2-Channel SPI ADC | Microchip
MCP3302T-CI/SL

MCP3302T-CI/SL - 13-Bit 2-Channel SPI ADC | Microchip

The Microchip Technology MCP3302T-CI/SL is a 13-bit successive-approximation analog-to-digital converter with two differential input channels, a 100 kHz conversion rate, and an SPI serial interface, housed in a 14-pin SOIC package. Its operating supply range is 4.5 V to 5.5 V, while the four analog inputs can be configured as two differential channels or four single-ended channels. These characteristics make the device suitable for sensor measurement, data acquisition, industrial monitoring, instrumentation, and embedded control systems. An ADC is a semiconductor that converts an analog voltage into a digital code for processing, storage, display, or control. The MCP3302 belongs to the SAR ADC family, where a successive-approximation internal DAC and comparator progressively determine the input voltage. In the power-management IC hierarchy, this converter bridges analog sensor signals and digital embedded systems, while its SPI interface provides a compact means of transferring conversion results to a microcontroller. The device provides 13-bit conversion resolution, two analog input channels, differential input support, and conversion rates up to 100 kHz. Differential operation rejects common-mode voltage and can improve measurement accuracy when the source is centered around a biased reference. The four single-ended inputs give additional flexibility for multiplexed measurements, while the SPI interface supports integration with embedded controllers without requiring a parallel data bus. The MCP3302 architecture uses a successive-approximation conversion process with an internal sample-and-hold function. During conversion, the SAR logic drives an internal DAC through successive bit trials until the internal comparator matches the sampled input voltage. The resulting 13-bit code is transferred through the serial interface. Exact input impedance, acquisition time, reference requirements, and current consumption must be confirmed from the manufacturer datasheet before defining the input network or acquisition timing. Typical uses include ratiometric pressure and temperature sensing, potentiometer position measurement, bridge-sensor instrumentation, industrial process monitoring, battery-powered remote data acquisition, and embedded control systems. The differential inputs are especially useful when a sensor output is referenced to a biased common-mode voltage. For low-level signals, careful grounding, reference filtering, and input-conditioning design remain essential because converter accuracy depends on the complete analog front end rather than on resolution alone. For each SPI transaction, use the manufacturer timing diagram to account for CS setup, sample-and-hold acquisition, conversion time, SCLK frequency, and output-data timing. Place the reference and input bypass capacitors close to their associated pins, maintain a low-impedance ground return, and avoid routing sensitive analog inputs adjacent to fast SPI clock traces. The MCP3302 datasheet and pin-description table should be used as the authority for board design and firmware sequencing. This page combines the exact MCP3302T-CI/SL package and interface details with a pin-compatible comparison, application guidance, and practical SPI interface considerations. It also identifies which specifications require direct confirmation from the manufacturer datasheet, helping engineers plan sensor acquisition before committing to PCB layout or embedded firmware.

RFQ پەیوەندی
MCP3302T-CI/ST - 13-Bit 4-Input SPI ADC | Microchip
MCP3302T-CI/ST

MCP3302T-CI/ST - 13-Bit 4-Input SPI ADC | Microchip

Microchip Technology MCP3302T-CI/ST is a 13-bit successive-approximation analog-to-digital converter with four single-ended or two differential inputs, conversion rates up to 100 ksps, and an SPI serial interface in a 14-pin TSSOP package. Its tested 2.7 V to 5.5 V operating supply range supports both 3.3 V and 5 V systems. An ADC is a data-conversion IC that transforms an analog voltage into a digital value for measurement, control, or signal processing. The MCP3302 belongs to the SAR ADC family, where a successive-approximation internal DAC compares the sampled input with successive trial voltages. Its differential-input architecture can reject common-mode noise, while single-ended operation simplifies connections for sensors, potentiometers, and resistive dividers. Key features include 13-bit resolution, four analog inputs, two differential channels, a 100 ksps maximum conversion rate, and an SPI-compatible serial interface. According to the manufacturer datasheet, the reference voltage can range from 400 mV to 5 V. This produces input-referred resolutions between 98 µV and 1.22 mV, depending on the selected reference voltage and gain configuration. The converter uses an internal sample-and-hold architecture and a successive-approximation conversion sequence. Differential channel selection is controlled through the serial interface, allowing two analog pairs to share one converter while maintaining consistent sampling and conversion timing. The SPI interface provides a straightforward connection to microcontrollers, although software must handle chip selection, clocking, and conversion-start timing. Typical uses include industrial process measurement, battery-powered sensor nodes, remote data acquisition, temperature sensing with thermistors or RTDs, potentiometer position measurement, and low-voltage analog monitoring. Differential inputs are particularly useful when the measured signal is small relative to system noise or when a sensor has a ground-referenced output that cannot be connected directly to a single-ended input. For reliable operation, keep the analog and digital return paths controlled, bypass the supply close to the device, and select a quiet reference source. Input voltage must remain within the ADC input range, and the common-mode limits of the differential inputs must be checked against the chosen reference and supply voltages before layout is finalized. This page combines converter specifications, package and interface guidance, practical application notes, and compatible replacement analysis. It is designed to help engineers determine whether the MCP3302T-CI/ST fits a precision measurement design and how to integrate it without overlooking reference, input-range, or SPI-timing constraints.

RFQ پەیوەندی
MCP3304-BI/P - 13-Bit 4-Channel 100ksps ADC | Microchip
MCP3304-BI/P

MCP3304-BI/P - 13-Bit 4-Channel 100ksps ADC | Microchip

The Microchip Technology MCP3304-BI/P is a 13-bit successive-approximation analog-to-digital converter with four differential or eight single-ended inputs, a 100 ksps conversion rate, an SPI serial interface, and a 16-pin PDIP package. It is designed for low-power battery-powered systems and remote data-acquisition equipment that require multiple analog channels in a compact through-hole package. An analog-to-digital converter, or ADC, converts continuously varying analog voltages into numerical values that a microcontroller or other digital controller can process. The MCP3304 belongs to the ADC and data-converter hierarchy and uses a successive-approximation register, or SAR architecture. In differential operation, each conversion references one analog input against another. In single-ended operation, the device can expose eight inputs relative to ground, giving designers flexibility in sensor and voltage-measurement circuits. The MCP3304-BI/P provides a 13-bit conversion resolution and a maximum sampling rate of 100 ksps. Published characteristics for the MCP3304-BI family include differential nonlinearity and integral nonlinearity of no more than ±1 LSB. Its SPI serial interface supports communication with embedded controllers, while its differential inputs are useful for rejecting common-mode noise when paired with suitable front-end circuitry. The internal SAR conversion process sequentially determines each output bit. This architecture is well suited to medium-speed measurement systems that do not require the sampling rate of a flash or pipeline ADC. The resulting combination of 13-bit resolution, four differential channels, low-power operation, and a 100 ksps maximum rate supports accurate acquisition of temperature, pressure, potentiometer, and other slowly changing analog signals. Typical uses include battery-operated environmental sensors, remote instrumentation, industrial process monitoring, laboratory data loggers, and embedded control systems. Multiple analog inputs reduce the need for separate converter packages, while the SPI interface allows the ADC to share a serialized bus with other peripherals. Careful reference grounding and input conditioning remain important when measuring small signals. Designers should verify the allowable analog and digital input ranges, acquisition time, reference-voltage limits, and recommended bypass-capacitor values in the manufacturer datasheet. The SPI clock and conversion timing should be coordinated with the host controller, and the analog input network should limit source impedance and switching noise. These checks are essential because timing or reference errors can undermine the apparent benefit of 13-bit resolution. This page consolidates verified distributor pricing, technical characteristics, package information, replacement availability, and practical selection guidance. It also distinguishes a documented same-family option from unsupported cross-package substitutions, helping engineers identify a replacement without assuming that a similar ADC is automatically pin-to-pin compatible.

RFQ پەیوەندی