ADC/DAC
بەرهەمەکان (3,600+)
AD974ARS - 4-Channel 16-Bit 200 kSPS ADC | Analog Devices
Analog Devices AD974ARS is a four-channel, 16-bit, 200 kSPS data acquisition system with a serial interface in a 28-pin SSOP package. It combines an input multiplexer, a high-speed successive-approximation switched-capacitor ADC, and an internal +2.5 V reference. The device operates from a single +5 V supply and supports 0 V to +4 V, 0 V to +5 V, or ±10 V analog input ranges. An ADC is an analog-to-digital converter, a data acquisition component that converts continuous analog voltage signals into digital values for processing, measurement, or transmission. In the AD974, the four-channel multiplexer sits ahead of the 16-bit sampling ADC, allowing one converter core to service four single-ended analog inputs. This ADC belongs to the data converter and data acquisition IC hierarchy rather than the broad category of general-purpose analog or digital semiconductors. The primary specifications are a 16-bit conversion resolution, 200 kSPS throughput, four single-ended input channels, and operation from one +5 V supply. The integrated reference is +2.5 V and may be selected as either an internal or external reference. Additional power-management features include a power-down mode, while the on-chip clock reduces the need for external timing circuitry. Maximum power dissipation is listed as 120 mW. Internally, the AD974 uses a successive-approximation, switched-capacitor conversion architecture. The input multiplexer routes one of four single-ended channels to the ADC core, while the sampling system establishes the voltage to be converted. Its serial interface provides a compact connection to a controller, DSP, or embedded processor. The supplied range of 4.75 V to 5.25 V accommodates regulated +5 V system rails while providing defined operating limits. Typical uses include industrial process monitoring, laboratory data logging, multichannel instrumentation, embedded measurement systems, and control equipment. It is especially relevant where four analog inputs must be digitized through a shared 16-bit converter rather than through four separate ADC packages. For lower-throughput acquisition, the multiplexer also reduces conversion contention between channels by sharing the ADC core. A key design consideration is the input-range configuration. The circuit must present only signals within the selected 0 V to +4 V, 0 V to +5 V, or ±10 V range, and the interface and reference arrangement must follow the manufacturer datasheet. Designers should also budget decoupling around the single +5 V supply and account for the 120 mW maximum power dissipation when choosing PCB copper area and the surrounding thermal environment. This product record combines manufacturer and distributor information, verified alternatives, package details, pricing, and application-focused engineering guidance. It is intended to make AD974ARS selection, sourcing, and design-in decisions faster while clearly identifying parameters that require confirmation against the manufacturer datasheet.
AD974ARSZ - 16-Bit 200 kSPS 4-Channel ADC | Analog Devices
The Analog Devices AD974ARSZ is a four-channel, 16-bit, 200 kSPS data acquisition system with a serial interface in a 28-pin SSOP package. It operates from a single 5 V supply and integrates a four-channel input multiplexer, a successive-approximation switched-capacitor ADC, a 2.5 V internal reference, and a power-down mode. The converter accepts 0 V to 4 V, 0 V to 5 V, or ±10 V analog input ranges. An ADC is an analog-to-digital converter, a semiconductor that samples continuous analog voltage and converts it into a numerical value. The AD974 belongs to the data converter hierarchy, combining an analog input multiplexer and sampling ADC into a dedicated data acquisition system. This integration reduces the number of separate analog-routing and conversion components required in instrumentation, industrial control, and signal-measurement equipment. The AD974ARSZ provides 16-bit resolution at up to 200 kSPS per conversion channel while operating from one 5 V supply. Its internal 2.5 V reference supports repeatable conversion measurements without requiring a separate reference circuit. A four-channel multiplexer allows one ADC to sample multiple analog sources sequentially. The serial interface reduces the number of signal connections required between the converter and a digital controller. Internally, the AD974 uses a successive-approximation, switched-capacitor conversion architecture. This architecture compares the sampled input against controlled internal references through successive conversion steps, producing a 16-bit digital result. The switched-capacitor network establishes the input-to-hold behavior of the sampling stage, while the internal reference and control logic coordinate conversion timing and data transfer. A power-down function can reduce activity when measurements are not required. Typical uses include multichannel process monitoring, industrial sensor acquisition, laboratory measurement systems, and factory automation equipment. The four-channel multiplexer is especially useful when several slowly changing sensor outputs must be measured through one converter. For waveforms requiring faster continuous sampling, the 200 kSPS rate should be evaluated against the required bandwidth, acquisition duration, and system response time. The primary design consideration is signal conditioning. Input amplitude must remain within the selected 0 V to 4 V, 0 V to 5 V, or ±10 V range, and the source impedance and settling behavior must suit the switched-capacitor input network. Use the manufacturer pin-description table and recommended application schematic to assign analog inputs, reference connections, supply decoupling, and serial-interface signals before PCB routing. This page combines the manufacturer's converter architecture, package information, input-range details, drop-in family options, and application-oriented design guidance. It helps engineers evaluate the AD974ARSZ as a complete four-channel acquisition front end rather than as an isolated sampling ADC.
AD974ARZ - 16-Bit 200 kSPS 4-Channel ADC | Analog Devices
The Analog Devices AD974ARZ is a 4-channel, 16-bit, 200 kSPS data acquisition system with a serial interface, an input multiplexer, a successive-approximation switched-capacitor ADC, and a 2.5 V internal reference in a 28-pin SOIC package. It operates from a single 5 V supply and supports 0 V to 4 V, 0 V to 5 V, and ±10 V analog input ranges. An ADC is an analog-to-digital converter, a semiconductor that converts continuous voltage signals into numeric data for processing, measurement, or transmission. The AD974 combines a four-channel multiplexer and a 16-bit sampling ADC in one device, making it a data acquisition system rather than a standalone converter. Its serial interface reduces the number of interconnects compared with a parallel converter while preserving the resolution needed for precision measurements. The AD974ARZ combines four single-ended analog input channels, a 200 kSPS maximum sampling rate, 16-bit resolution, and a 2.5 V internal reference. A single 5 V supply simplifies system power design. The device also provides a power-down mode, allowing its power consumption to be reduced when conversions are not required. These features suit multichannel industrial instrumentation, process control, sensor acquisition, laboratory measurement, and embedded data logging. Internally, the four-channel input multiplexer routes the selected input to a high-speed switched-capacitor successive-approximation ADC. Conversion results are transferred through the serial interface. The architecture combines channel selection, conversion, and reference functions in a single IC, reducing the component count required for a multi-input measurement subsystem. Selection of the analog input range is handled by the device architecture rather than requiring four independent converter packages. The AD974ARZ is appropriate when several analog sources must be digitized through one compact, low-power interface. It can be used in industrial process monitoring, factory automation, medical instrumentation, portable measurement equipment, and test systems. Its 16-bit resolution supports detailed signal representation, while the 200 kSPS throughput provides enough conversion bandwidth for many slowly varying or multiplexed measurements. System-level signal conditioning, grounding, and reference requirements still depend on the source impedance and measurement accuracy target. For layout, place input and reference-related components close to their associated pins and preserve a quiet return path around the analog inputs. Because the converter uses switched-capacitor internal nodes, stable reference and supply bypassing are important. A multilayer board with a solid ground plane is generally preferable to relying on long analog traces. Designers must also verify acquisition timing, serial-interface timing, input settling, and the selected voltage range against the complete acquisition cycle. This page combines verified manufacturer information, distributor listings, same-family package comparisons, and practical design guidance. It also distinguishes confirmed drop-in evidence from package variants and clearly identifies missing electrical details rather than estimating unverified specifications.
AD974BN - 4-Channel 16-Bit 200 kSPS ADC | Analog Devices
The Analog Devices AD974BN is a four-channel, 16-bit, 200 kSPS data acquisition system with a serial interface, packaged in a 28-pin PDIP. It integrates a four-channel input multiplexer, a high-speed successive-approximation switched-capacitor ADC, a +2.5 V reference, and a single +5 V supply. The supported analog input ranges are 0 V to +4 V, 0 V to +5 V, and ±10 V. An ADC converts continuously varying analog signals into numeric values for measurement, control, or signal processing. The AD974BN combines four single-ended analog inputs with a common 16-bit conversion engine, making it useful when several sensors or voltage signals must be sampled by a compact system. Its serial interface reduces the number of parallel data lines needed on the PCB and supports communication with a digital controller. The converter provides 16-bit nominal resolution and 200 kSPS throughput. These figures define the balance between measurement detail and acquisition speed: the device samples up to 200,000 times per second while representing each selected channel with 16-bit digital data. The integrated reference is +2.5 V, and the system operates from a single +5 V supply. A power-down mode is also included for applications that need to reduce consumption when conversion is not required. The AD974 architecture uses a four-channel input multiplexer and a successive-approximation switched-capacitor conversion process. The input multiplexer selects one of four single-ended analog channels for conversion, while the serial interface transfers conversion results. The integrated 2.5 V reference provides a defined internal reference option, and the datasheet states that the device supports either external or internal reference selection. Typical applications include industrial process monitoring, sensor signal acquisition, laboratory instrumentation, communications equipment, and embedded measurement systems. The four-channel structure is useful when monitoring multiple voltages sequentially, while the 200 kSPS rate supports measurements where moderate-to-high sampling throughput is needed without requiring a parallel ADC output interface. When designing around the AD974BN, preserve adequate analog and digital return paths, place input-conditioning components close to the relevant pins, and account for the selected input range when defining signal scaling. The serial interface timing and power-down behavior should be checked against the controller requirements in the Analog Devices AD974 datasheet.
AD974BNZ - 4-Channel 16-Bit 200 kSPS ADC | Analog Devices
The Analog Devices AD974BNZ is a four-channel, 16-bit, 200 kSPS data acquisition system with a serial interface, housed in a 28-pin PDIP package. It accepts unipolar 0 V to +4 V, 0 V to +5 V, or bipolar ±10 V analog input ranges. The device operates from a single +5 V supply and includes a four-channel input multiplexer, a high-speed successive-approximation switched-capacitor ADC, and an internal +2.5 V reference. An ADC is a data acquisition IC that converts continuous analog voltages into digital values for processing, measurement, or transmission. In the broader semiconductor hierarchy, the AD974 belongs to the ADC/DAC class of interface ICs and supports instrumentation, industrial control, and embedded signal-processing systems. Its multiplexer permits four single-ended analog inputs to share one high-resolution conversion core, reducing the number of separate converters required in a multichannel design. The AD974's principal specifications include 16-bit resolution, 200 kSPS throughput, four single-ended channels, a +5 V supply, and selectable input ranges of 0 V to +4 V, 0 V to +5 V, or ±10 V. Maximum power dissipation is listed as 120 mW. A power-down mode is included for systems that need to reduce consumption when conversion activity is not required. The internal architecture combines the input multiplexer with a high-speed, 16-bit, successive-approximation switched-capacitor ADC. The serial interface provides the converted result to a digital controller or processor. According to the Analog Devices product page and manufacturer datasheet, the internal +2.5 V reference supports the converter without requiring a separate reference source, while the common +5 V supply simplifies system-level power distribution. Typical uses include four-channel process monitoring, sensor signal acquisition, laboratory measurement systems, industrial data logging, and embedded control equipment. The 0 V to +5 V range is particularly useful for systems whose sensor outputs remain within a unipolar 5 V envelope, while the ±10 V option can simplify interfacing with conventional bipolar industrial signals when the surrounding circuitry provides suitable protection and conditioning. Designers should account for input settling, conversion timing, serial-interface implementation, and the voltage headroom required by each selected range. External filtering or source impedance can affect acquisition accuracy, so the signal source and conditioning network should be evaluated together with the acquisition timing. The available manufacturer information identifies a maximum power dissipation of 120 mW but does not provide a verified thermal-resistance value in the supplied data. This page combines manufacturer specifications, distributor availability, verified package information, drop-in comparison options, and practical acquisition-system guidance. It separates documented performance from unavailable details so engineers can review the AD974BNZ for data acquisition, test, and industrial control designs without relying on unverified replacement claims.
AD974BR - 4-Channel 16-Bit 200kSPS ADC | Analog Devices
The Analog Devices AD974BR is a four-channel, 16-bit, 200 kSPS data acquisition system with a high-speed serial interface, packaged in a 28-pin SOIC. It combines a four-channel analog input multiplexer, a successive-approximation switched-capacitor ADC, a +2.5 V internal reference, and an on-chip clock. The converter operates from a single +5 V supply and supports 0 V to +4 V, 0 V to +5 V, and ±10 V analog input ranges. Its 200 kSPS throughput and 16-bit resolution make it suitable for precision signal acquisition, industrial measurement, instrumentation, and embedded control systems where multiple analog channels must be digitized with limited board space. A data acquisition system combines analog multiplexing, sampling, quantization, conversion, and a digital interface into one integrated device. This integration reduces the number of external components and simplifies synchronization between analog channels. The AD974BR is a low-power ADC/data acquisition IC within the broader semiconductor hierarchy: data acquisition system → analog-to-digital converter → ADC/DAC component. Its internal reference and on-chip clock are particularly useful when a system requires repeatable conversions without relying on separate reference and timing components. The principal features are a 16-bit conversion resolution, 200 kSPS throughput, four single-ended analog input channels, and a single +5 V supply. The device accommodates several input ranges, including 0 V to +4 V, 0 V to +5 V, and ±10 V. A power-down mode helps reduce consumption when acquisition is not required, while the serial interface supports integration with digital controllers. The manufacturer describes the AD974 as a low-power data acquisition system, and the verified product information identifies a maximum power dissipation of 120 mW. The AD974 uses a successive-approximation switched-capacitor conversion architecture. This architecture is appropriate for acquisition systems that need deterministic sampling, compact implementation, and direct digital output without a complex high-frequency pipeline. The four-channel multiplexer allows one ADC core to process multiple analog inputs sequentially. The serial interface is useful when the converter is connected to a microcontroller, DSP, programmable controller, or other data-processing device; however, the exact supported clock, framing, and output timing must be confirmed from the manufacturer datasheet before final interface design. Typical applications include industrial process monitoring, laboratory instrumentation, sensor-interface systems, factory automation, medical instrumentation, and embedded measurement platforms. The four-channel structure is useful when several analog sensors or conditioned signals must be scanned through one converter. The 200 kSPS sampling rate supports applications requiring periodic measurement rather than high-bandwidth waveform capture. The 16-bit format provides fine numerical resolution for control loops and measurement systems, while the single +5 V supply simplifies power architecture. Designers should confirm the package pinout, analog input configuration, reference selection, clock requirements, and serial-interface timing from the AD974 datasheet. Input conditioning, filtering, grounding, and protection must be selected for the intended voltage range. The SOIC package also requires attention to thermal dissipation and copper routing, particularly when the converter operates continuously at its maximum sampling rate. This page combines verified Analog Devices product information, distributor listing details, package data, and practical acquisition-system guidance. It distinguishes documented parameters from information that still requires datasheet confirmation, helping engineers evaluate the AD974BR for precision multichannel measurement without relying on unverified specifications.
AD974BRS - 4-Channel 16-Bit 200 kSPS ADC | Analog Devices
The Analog Devices AD974BRS is a four-channel, 16-bit, 200 kSPS data acquisition system with a serial interface, housed in a 28-SSOP package. It combines a four-channel input multiplexer, a high-speed 16-bit sampling ADC, an internal 2.5 V reference, and a single +5 V supply. The converter supports 0 V to +4 V, 0 V to +5 V, and ±10 V analog input ranges. Maximum power dissipation is 120 mW, and the device includes a power-down mode for reduced operating power. It is designed for multichannel measurement systems where several analog signals must be converted through a compact serial interface. An ADC is an analog-to-digital converter, a semiconductor that transforms continuously varying analog voltage into numerical data. Within the broader hierarchy, the AD974BRS is a data acquisition system and sampling ADC, belonging to the ADC/DAC and integrated-circuit categories. Its internal multiplexer reduces the number of physical input channels required from the host processor while retaining independent conversion capability for four single-ended analog inputs. The principal features include 16-bit resolution, 200 kSPS throughput, four single-ended analog inputs, a 5 V single-supply architecture, and both internal and external 2.5 V reference options. The on-chip clock reduces the number of external timing components required in a basic acquisition circuit. Power-down operation can also reduce consumption when the measurement system is not actively sampling, although the complete converter specifications and timing behavior must be checked in the manufacturer datasheet before sequencing external analog switches. The AD974BRS uses a successive-approximation, switched-capacitor conversion architecture. This approach provides a compact ADC core suitable for precision multichannel measurement. Its serial interface reduces the number of data connections required between the converter and a digital controller, but it also makes software timing and clock configuration important. Because all channels share one internal ADC and reference system, calibration considerations and channel-to-channel performance should be evaluated for the intended instrumentation system. Typical uses include industrial process monitoring, laboratory data acquisition, environmental sensing, portable instrumentation, and embedded measurement systems. The four-channel multiplexer is useful when several sensor outputs must be sampled into one controller. The ±10 V input option is particularly relevant for legacy industrial interfaces, while the narrower ranges can be used with appropriately conditioned low-voltage sensors. The 5 V supply requirement also simplifies integration with systems that already operate from a regulated 5 V rail. Designers should preserve the analog input range and reference requirements of each channel, verify acquisition timing against the serial-interface clock, and use source and termination networks that do not distort the sampled signal. External reference and input filtering choices can affect accuracy and settling behavior, so the manufacturer’s recommended application circuit should be treated as the baseline design. This page consolidates the verified manufacturer specifications, distributor sourcing information, package details, application guidance, and same-family replacement information into a design-focused reference for engineers evaluating the AD974BRS.
AD974BRSZ - 16-Bit 4-Channel ADC | Analog Devices
Analog Devices AD974BRSZ is a four-channel, 16-bit, 200 ksps data-acquisition ADC with a serial interface, a single 5 V supply, an internal 2.5 V reference, and a 28-pin SSOP package. It accepts analog input ranges of 0 V to 4 V, 0 V to 5 V, or ±10 V, depending on the selected input configuration. An ADC, or analog-to-digital converter, converts continuous analog voltages into digital codes for processing, measurement, or transmission. The AD974 belongs to the data-acquisition-system hierarchy: its internal four-channel multiplexer routes selected analog inputs to a successive-approximation, switched-capacitor ADC, while the serial interface transfers conversion results to a digital controller. This integration reduces the number of separate front-end components required in multichannel measurement systems. The AD974BRSZ combines 16-bit resolution with a maximum conversion rate of 200 ksps. Its four-channel multiplexer supports simultaneous acquisition sequencing, while the internal 2.5 V reference provides a stable conversion baseline. Operation from a single 5 V supply simplifies system power design, and the integrated power-down mode can reduce consumption when measurements are not continuously required. Internally, the converter uses a successive-approximation, switched-capacitor architecture. Successive-approximation ADCs determine each output code through a sequence of internal comparisons, providing a practical combination of resolution, conversion speed, and power consumption. The high-speed serial interface is designed to reduce the number of interconnects required when the converter communicates with a digital acquisition system. Typical uses include industrial process monitoring, instrumentation, laboratory data acquisition, communications equipment, and embedded measurement systems. Four analog channels are particularly useful when monitoring several related signals, such as temperature, pressure, position, and analog control feedback. The accepted input ranges make the converter applicable to unipolar sensor outputs as well as bipolar instrumentation signals. A critical design consideration is preserving the integrity of each analog input through properly terminated PCB traces, low-noise references, and appropriate source-impedance networks. The analog and digital return paths should be arranged carefully to reduce conversion error and coupling between the four measured channels. The manufacturer datasheet should be used when assigning the 28 package pins and configuring operating modes. This page combines the manufacturer specifications with practical ADC design guidance, package information, application fit, and same-family ordering alternatives. It is intended to help engineers identify the correct interface, input range, package, and operating conditions before integrating the AD974BRSZ into a measurement design.
AD974BRZ - 4-Channel 16-Bit 200kSPS ADC | Analog Devices
The Analog Devices AD974BRZ is a four-channel, 16-bit, 200 kSPS data acquisition system with a high-speed serial interface, housed in a 28-pin SOIC package. It operates from a single +5 V supply, accepts 0 V to +4 V, 0 V to +5 V, or ±10 V analog input ranges, and integrates a four-channel input multiplexer, a successive-approximation switched-capacitor ADC, and a +2.5 V reference. The AD974 is factory calibrated to minimize linearity and offset errors, while a power-down mode reduces consumption when conversion activity is not required. An ADC is an analog-to-digital converter, a semiconductor that samples continuous voltage signals and converts them into digital codes for processing, measurement, or transmission. In the product hierarchy, the AD974BRZ is a data acquisition system that integrates an ADC, analog multiplexer, voltage reference, and serial interface. This integration reduces the number of separate components required in instrumentation, industrial control, test equipment, and embedded measurement systems. The AD974BRZ combines 16-bit resolution with a throughput of 200 kSPS across four single-ended input channels. Its internal 2.5 V reference provides the conversion reference, and the serial interface transfers converted data to a host processor. Factory calibration supports repeatable performance without requiring the user to perform the complete converter calibration procedure. The device also supports analog input ranges suitable for bipolar instrumentation as well as unipolar sensor signals. The internal architecture uses a four-channel analog multiplexer followed by a high-speed successive-approximation, switched-capacitor sampling ADC. Multiplexing four inputs through one converter provides a practical balance between channel count, conversion throughput, power consumption, and package size. This architecture is appropriate when several sensors share a common sampling rate and data-conversion clock rather than requiring simultaneous independent conversion on every channel. Typical uses include multichannel process monitoring, laboratory data logging, factory automation, sensor-interface modules, and embedded measurement systems. The 200 kSPS rate is suitable for many industrial and instrumentation signals, while the 16-bit format provides 65,536 digital codes across the selected input range. For applications requiring simultaneous sampling, substantially faster conversion, or more input channels, a different ADC architecture should be evaluated. A critical design consideration is the relationship between input amplitude, selected range, source impedance, and acquisition time. The 120 mW maximum power dissipation and single +5 V supply simplify power planning, but analog input conditioning and grounding remain essential for accurate conversion. Protect unused channels and control signals according to the manufacturer datasheet, and verify the complete pinout and signal names before PCB layout. This page consolidates verified manufacturer and distributor information, procurement guidance, application analysis, and the limits of available drop-in replacements. It also distinguishes published AD974 family options from genuine pin-compatible substitutes, helping engineers avoid treating different package variants as drop-in components.
AD9751ASTZ - 10-Bit 300 MSPS TxDAC+ DAC | Analog Devices
The AD9751ASTZ is a dual muxed port, ultra high-speed, single-channel, 10-bit CMOS digital-to-analog converter (DAC) from Analog Devices. It integrates a high-quality 10-bit TxDAC+ core, a voltage reference, and digital interface circuitry into a compact 48-lead LQFP (7x7 mm) package. The device supports update rates up to 300 MSPS, making it suitable for high-speed waveform generation, direct digital synthesis (DDS), and communications applications. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current signal. DACs are essential in systems where digital processing must interface with the analog world, such as audio playback, video rendering, and RF signal generation. The AD9751 belongs to the TxDAC+ family, a series of high-speed DACs optimized for transmit path applications in communication systems. These DACs are part of the broader data converter category, which includes ADCs and DACs, and are critical in mixed-signal processing chains. Key features of the AD9751ASTZ include a 10-bit resolution, a maximum update rate of 300 MSPS, and a dual muxed port interface that allows interleaved data input for high-speed operation. The device operates from a 3.0V to 3.6V supply, with a typical full-scale output current of 20 mA. It offers excellent AC and DC performance, including a spurious-free dynamic range (SFDR) of 68 dBc at 10 MHz output, and a low glitch energy of 5 pV-s. The integrated voltage reference simplifies design, while the 48-lead LQFP package provides a compact footprint for space-constrained applications. Technically, the AD9751 uses a segmented current-steering architecture, which balances speed and linearity. The dual muxed port allows the DAC to accept data from two parallel input ports, effectively doubling the data throughput. The device includes a clock input that latches data on the rising edge, and it supports both binary and two's complement input formats. The output is a differential current, which can be converted to a voltage using an external resistor or transformer. The device also features a power-down mode to reduce consumption when idle. Typical applications include base station transmit paths, arbitrary waveform generators, and high-speed instrumentation. In a base station, the AD9751 converts digital baseband signals to analog IF signals for upconversion. Its high update rate and low noise make it ideal for generating clean, wideband signals. In test equipment, it enables precise waveform synthesis for signal generation and modulation analysis. When designing with the AD9751ASTZ, ensure proper decoupling of the analog and digital supply pins, and use a low-jitter clock source to maximize SFDR. The output current should be terminated with a 50-ohm load or transformer to achieve optimal performance.
AD9751ASTZRL - 10-Bit 300 MSPS TxDAC+ DAC | Analog Devices
The AD9751ASTZRL is a dual muxed port, ultra high-speed, single-channel, 10-bit CMOS digital-to-analog converter (DAC) from Analog Devices. It integrates a high-quality 10-bit TxDAC+ core, a voltage reference, and digital interface circuitry into a compact 48-lead LQFP package. The device supports output update rates up to 300 MSPS, making it suitable for high-speed communication and signal synthesis applications. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current signal. DACs are essential in systems where digital processing must interface with the analog world, such as in transmitters, waveform generators, and audio equipment. The AD9751 belongs to the TxDAC+ family, which is optimized for high-speed, high-performance transmit paths in communication systems. Key features of the AD9751 include excellent spurious-free dynamic range (SFDR) and intermodulation distortion (IMD) performance, with SFDR to Nyquist at 25 MHz output of 64 dB. It also features an internal clock doubling PLL, differential current outputs, and a flexible digital interface. The device operates from a single 3.3V supply and includes a power-down mode for reduced power consumption. The AD9751 uses a segmented current-source architecture to achieve high linearity and low glitch energy. The dual muxed port architecture allows interleaving of data from two input ports, effectively doubling the data throughput. The internal PLL can double the input clock, simplifying system clocking. The device is specified over the industrial temperature range of -40°C to +85°C. Typical applications include base stations, wireless local loop, digital radio links, direct digital synthesis (DDS), and arbitrary waveform generation. The high update rate and excellent dynamic performance make it ideal for generating complex modulated waveforms in communication transmitters. When designing with the AD9751, careful attention to PCB layout is required to minimize parasitic capacitance and inductance, especially on the high-speed digital inputs and analog outputs. Proper decoupling of the analog and digital supplies is essential to achieve the specified dynamic performance.
AD9768JQ - 8-Bit 100 MSPS ECL DAC | Analog Devices
The Analog Devices AD9768JQ is an 8-bit, current-output digital-to-analog converter operating at update rates up to 100 MSPS and packaged in an 18-pin CERDIP. It accepts ECL-level digital inputs and can also operate as a two-quadrant multiplying DAC with multiplying bandwidth up to 40 MHz. The verified source reports a 5 ns digital input characteristic and a starting distributor price of $15.2202 as of 2026-10-23. A DAC is a data-acquisition and signal-generation component that converts parallel digital codes into proportional current or voltage. The AD9768 belongs to the converter hierarchy: digital-to-analog converter, current-output DAC, data converter, and semiconductor IC. Its current-output architecture is useful when the downstream circuit requires a high-speed current-to-voltage conversion stage or direct current-domain signal processing. The AD9768 provides 8-bit resolution and supports update rates as high as 100 MSPS. Its ECL-level digital interface is designed for high-speed systems, while the multiplying capability allows the DAC to be used in signal-generation, modulation, waveform-shaping, and feedback applications. The low-glitch architecture highlighted by the manufacturer is relevant to reducing unwanted transient energy during digital-code transitions, although exact glitch specifications require the complete AD9768 datasheet. Typical circuit use places the converter between an 8-bit digital source and a current-to-voltage or load network. Because the output is current-based, external analog circuitry, impedance matching, and careful grounding strongly influence signal quality. The manufacturer describes operation as a standard DAC or as a two-quadrant multiplying DAC, giving designers flexibility for both ordinary waveform generation and multiplier-style signal paths. When designing a board around the AD9768JQ, verify the exact pinout, supply requirements, input logic levels, output compliance, and timing margins from the AD9768 datasheet. The 18-pin CERDIP package is not interchangeable with a surface-mount DAC without a deliberate PCB redesign. The verified distributor result identifies the package as 18-CERDIP, while other electrical values not present in the supplied data are intentionally not guessed.
AD976AAN - 16-Bit 200 kSPS ADC | Analog Devices | Industrial
The Analog Devices AD976AAN is a 16-bit successive-approximation analog-to-digital converter with a 200 kSPS throughput rate, one analog input, and a 28-pin PDIP package. It operates from a single 5 V supply, accepts a standard industrial analog range of ±10 V, and uses a parallel data interface. The converter also includes an internal 2.5 V reference, an on-chip clock, and factory calibration that minimizes linearity errors. An ADC is a data-conversion IC that transforms a continuous analog voltage into a digital number for processing, measurement, or transmission. The AD976A belongs to the successive-approximation, or SAR, ADC family. SAR converters compare the sampled input with an internal reference through a successive series of conversion steps. This architecture is widely used where moderate conversion speed, compact size, and direct parallel digital output are more important than very high sample rates. The AD976AAN provides a throughput rate of 200 kSPS and 16-bit resolution, producing 65,536 possible digital codes for each conversion. Its single 5 V supply simplifies system power design, while the parallel interface allows the converted value to be read directly by suitable digital logic. A factory-calibrated internal 2.5 V reference provides a convenient default for acquisition systems, and the device also supports an external reference when greater system-level control is required. The AD976A uses Analog Devices’ proprietary BiCMOS process, combining high-performance bipolar devices with CMOS circuitry. Internally, the converter is based on a switched-capertor successive-approximation architecture. The analog front end accepts the standard industrial ±10 V range, while the 28-pin parallel-interface package provides straightforward connection to digital control and data-capture circuitry. The maximum power dissipation stated in the datasheet is 100 mW. Typical uses include industrial process measurement, laboratory data-acquisition equipment, industrial control systems, communications equipment, and embedded instrumentation. The 200 kSPS rate is appropriate for acquiring many analog signals or control channels while the 16-bit word length preserves fine amplitude detail. The manufacturer identifies the AD976AAN as an industrial-grade, through-hole 28-pin DIP device. For a new design, preserve the ±10 V input-signal path and 5 V supply architecture around the converter, and follow the manufacturer datasheet for reference, analog-input, digital-interface, and decoupling connections. Pay particular attention to source impedance and acquisition timing because the switched-capacitor SAR input presents a sampled load during each conversion. This page combines the manufacturer’s converter specifications with practical selection guidance, verified pin-compatible family alternatives, comparison parameters, and design considerations. It helps engineers evaluate the AD976AAN alongside the AD976 and AD976AANZ while preserving package and interface constraints.
AD976AANZ - 16-Bit 200 kSPS SAR ADC | Analog Devices
The Analog Devices AD976AANZ is a 16-bit, single-input successive-approximation analog-to-digital converter with a 200 kSPS throughput rate, operating from a single 5 V supply and housed in a 28-pin PDIP package. The converter combines a high-speed sampling architecture with parallel digital output for applications requiring deterministic acquisition and direct parallel-interface integration. An ADC is an integrated circuit that converts an analog input voltage into a numeric representation for processing, measurement, or control. The successive-approximation ADC category compares the input voltage with an internally generated reference through a sequence of conversion decisions. Within the broader semiconductor hierarchy, the AD976AANZ is an ADC, an interface IC, and a data-acquisition component designed for precision signal measurement. Key features include 16-bit resolution, a 200 kSPS maximum throughput rate, single 5 V operation, one analog input, and a parallel output interface. The AD976A family uses a switched-capacitor architecture and a proprietary BiCMOS process combining bipolar and CMOS technologies. According to Analog Devices product information, each converter includes an ADC core, reference, and on-chip clock, reducing the number of external timing and reference components required for a complete conversion channel. Factory calibration and production testing support consistent offset, gain, linearity, signal-to-noise ratio, and total harmonic distortion performance. The parallel interface exposes the converted digital result across dedicated output lines rather than relying on a serial protocol. This architecture simplifies connection to parallel processors, digital logic, and acquisition systems while avoiding the serial-clock and data-framing overhead of serial-output converters. Typical uses include industrial process measurement, instrumentation, waveform capture, data-acquisition systems, communications equipment, and embedded control applications. The 200 kSPS rate is suitable for continuous monitoring of moderately changing analog signals, while 16-bit resolution provides 65,536 digital codes across the selected analog input range. Designers should account for the single 5 V supply, reference accuracy, source impedance, acquisition time, input range, and digital timing before layout. Use the pin-description and timing information in the Analog Devices datasheet to assign tracks and connect decoupling, input-conditioning, and data-bus networks. This product page consolidates the verified AD976AANZ specifications, package information, sourcing guidance, replacement analysis, and practical integration considerations into an engineering-focused reference that extends beyond a basic distributor listing.
AD976AAR - 16-Bit 200 kSPS ADC | Analog Devices
Analog Devices AD976AAR is a high-speed, low-power, 16-bit successive-approximation analog-to-digital converter with a 200 kSPS throughput rate, a single 5 V supply, and a 28-lead SOIC package. The converter uses a switched-capacitor sampling architecture, an internal 2.5 V reference, an on-chip clock, and a high-speed parallel output interface. It is designed for precision signal acquisition where 16-bit resolution and moderate conversion speed are required. An ADC is an analog-to-digital converter, a semiconductor that samples a continuously varying voltage and represents it as a numerical value. The AD976AAR belongs to the successive-approximation ADC family and uses switched-capacitor sampling. This combination places it within the hierarchy of data-converter ICs, analog-to-digital converters, signal-chain semiconductors, and electronic components used in industrial measurement and control systems. The AD976A reaches 200 kSPS, while the related AD976 operates at 100 kSPS. Both provide 16-bit conversion resolution, operation from one 5 V supply, selectable external or internal reference options, and a parallel interface. The internal 2.5 V reference provides a convenient starting point for single-supply designs, while external-reference selection can support systems that require a shared precision reference. The AD976 family is fabricated using Analog Devices' proprietary BiCMOS process, combining high-performance bipolar devices with CMOS transistors. A switched-capacitor ADC uses an internal sampling network to hold the input voltage during conversion. The parallel interface exposes the converted digital result directly across device pins, reducing serial-interface overhead and supporting designs where the destination device can latch data in parallel. Typical uses include industrial process monitoring, instrumentation, waveform acquisition, communications equipment, control systems, and embedded measurement platforms. The 28-lead SOIC package is suitable for conventional surface-mount PCB assembly and provides enough connections for analog input handling, reference selection, digital data output, control signals, and power delivery. Before layout is finalized, use the Analog Devices AD976A datasheet to assign every signal, identify supply and ground pins, and confirm the recommended input, reference, and bypass-capacitor networks. Treat the 200 kSPS throughput rate as the maximum sampling capability and evaluate acquisition timing, acquisition time, source impedance, and the destination logic before fixing system clocking. This product page combines the manufacturer's device information with engineering-oriented guidance covering application fit, package constraints, interface implementation, and verified replacement options. It also identifies where the AD976AARZ shares the same 28-lead SOIC footprint, helping designers determine whether a suffix-based sourcing change can preserve the existing PCB layout.
AD976AARS - 16-Bit 200 kSPS SAR ADC | Analog Devices
Analog Devices AD976AARS is a 16-bit successive-approximation analog-to-digital converter with a sampling throughput of 200 kSPS, a single 5 V supply, and a 28-lead SSOP package. The converter uses a switched-capacitor architecture and provides a high-speed parallel output interface for direct connection to digital acquisition logic. Its internal 2.5 V reference can also be configured for external-reference operation, giving designers flexibility in measurement-system calibration. An ADC is an interface component that converts a continuous analog voltage into a numeric digital value. The AD976A belongs to the successive-approximation ADC family, which repeatedly compares the sampled input against a generated reference value. Within the broader semiconductor hierarchy, this device is a data-converter IC, an interface IC, and a data-acquisition building block. Compared with flash or pipeline converters, its switched-caparitor SAR architecture is suited to moderate-speed, high-resolution measurements where parallel digital output and deterministic conversion are useful. The principal operating characteristics are 16-bit resolution, 200 kSPS throughput, and operation from one 5 V supply. The Analog Devices manufacturer datasheet states that the AD976A consumes no more than 100 mW and that its reference can be internal or external. A 28-lead SSOP package provides a compact surface-mount option for instrumentation, industrial control, communications, and embedded measurement systems. The parallel interface exposes the conversion result directly without requiring a serial output protocol. The AD976A contains a switched-capacitor SAR conversion core, a 2.5 V reference, and a parallel output interface. A 100 kSPS AD976 variant offers a lower conversion rate, while the AD976A doubles throughput to 200 kSPS. At every conversion, the device samples the analog input and performs a sequence of bit decisions to produce a 16-bit code. Because the output is parallel, timing margins between the converter, acquisition control logic, and downstream latch or processor interface remain important design considerations. Typical uses include multichannel process-control acquisition, waveform digitization, communications demodulation, laboratory measurement equipment, and industrial sensor interfaces. In each case, the converter can sample a conditioned analog waveform and present each 16-bit result to digital logic at its parallel output. The single 5 V supply simplifies system power planning, while selectable internal or external reference voltage supports both standalone operation and precision system calibration. Designers should provide stable analog and reference bypassing, account for digital-output timing when interfacing the parallel bus, and verify acquisition timing against the 200 kSPS conversion rate. Input-source impedance, acquisition time, signal bandwidth, and the system clock arrangement can affect achievable accuracy. The manufacturer pin-description table should be used to assign every trace and establish unambiguous logic levels before fabrication. This product page combines the AD976AARS operating facts with package guidance, application analysis, verified family alternatives, and practical design considerations. It is intended to help engineers evaluate conversion speed, interface architecture, supply requirements, and replacement strategy before integrating the converter into a precision data-acquisition design.
AD976AARSZ - 16-Bit 200 kSPS ADC | Analog Devices
The Analog Devices AD976AARSZ is a 16-bit, single-channel, successive-approximation analog-to-digital converter operating from a single 5 V supply and delivering a throughput rate of 200 kSPS. The device is packaged in a 28-pin SSOP and uses a high-speed parallel output interface. These characteristics make it suitable for precision signal acquisition, industrial control, instrumentation, communications, and test equipment requiring moderate conversion speed with 16-bit resolution. An ADC is a data-acquisition IC that converts an analog input voltage into a digital number. The AD976A belongs to the successive-approximation ADC category, where an internal sample-and-hold circuit, comparator, and switched-capacitor conversion network determine the final 16-bit code. The AD976A combines this conversion mechanism with a parallel digital interface, allowing acquired samples to be read directly by a digital processor, field-programmable logic, or data-capture system. Key features of the AD976AARSZ include 16-bit resolution, a maximum throughput of 200 kSPS, single 5 V operation, an internal 2.5 V reference, and a parallel output interface. According to the Analog Devices AD976A product information, the converter uses Analog Devices' proprietary BiCMOS process, combining high-performance bipolar devices with CMOS circuitry. Factory calibration minimizes the need for external offset and gain correction in many applications. The AD976A is related to the AD976 family, but the AD976A has the higher 200 kSPS throughput rate. The manufacturer describes the AD976A as a high-speed, low-power converter, with maximum dissipation listed at 100 mW for the AD976/AD976A family. Its internal reference simplifies system design by removing the need for an external reference source, while the parallel interface requires careful attention to output timing and data-acquisition setup. Typical uses include closed-loop industrial control, analog sensor interfaces, waveform capture, process monitoring, communications receivers, and laboratory instrumentation. The 16-bit code width provides 65,536 digital output levels, while the 200 kSPS rate supports sampling of relatively slow or medium-bandwidth signals rather than high-definition video or high-frequency radar waveforms. When laying out a circuit, treat the analog input and digital output paths as separate domains. Place input and reference decoupling capacitors close to their associated pins, route the 16-bit parallel bus over controlled-length traces, and terminate unused digital inputs consistently. The manufacturer datasheet pin-description table should be used when assigning PCB nets and checking the 28-pin SSOP land pattern. This page combines the manufacturer specifications with practical interface guidance, verified distributor availability information, a package-matched comparison, and design notes focused on decoupling, grounding, and parallel-bus implementation. These engineering details help shorten evaluation time when the AD976AARSZ is being considered for a new 16-bit acquisition channel.
AD976ABN - 16-Bit 200kSPS SAR ADC, 5V, 28-PDIP | Analog Devices
The Analog Devices AD976ABN is a 16-bit, 200 kSPS successive-approximation analog-to-digital converter housed in a 28-pin PDIP through-hole package, designed for high-speed, low-power data acquisition on a single 5 V supply. Headline specifications include 200 kSPS throughput (the AD976 without the "A" suffix is 100 kSPS), 100 mW maximum power dissipation, and an internal 2.5 V reference that can be overridden with an external source for ratiometric or precision systems. The part contains a successive-approximation switched-capacitor ADC core with self-calibration logic, an on-chip clock, a high-speed parallel interface, and a choice of internal or external reference operation. What is a SAR ADC? A successive-approximation-register analog-to-digital converter is a sampling converter that uses a binary-search algorithm against an internal DAC and comparator to resolve one bit per clock cycle. SAR ADCs sit at the intersection of precision (16-bit and higher) and moderate speed (tens of kSPS to a few MSPS), outperforming flash and pipelined converters in power efficiency and latency while trading off raw speed. They are widely used in industrial process control, instrumentation, and data-acquisition boards where dc-to-audio bandwidth signals must be digitized without the pipeline delay of a pipelined ADC. Key features include single 5 V supply operation, 100 mW max power dissipation, internal 2.5 V reference (with external override), on-chip clock generator, factory-calibrated linearity (no user calibration required), and a high-speed parallel interface for direct connection to microprocessors, FPGAs, or DSP data buses. Input ranges are configured for unipolar 0-5 V or bipolar ±10 V operation with the proper front-end scaling. The 200 kSPS throughput of the AD976A is double the AD976 100 kSPS rate, making it the preferred choice where the bus and downstream logic can sustain the higher sample rate. Architecturally, the AD976ABN is built on a BiCMOS process that combines bipolar precision devices for the input front-end and reference buffer with CMOS logic for the SAR engine, clock, and digital interface. The switched-capacitor input architecture provides inherent sample-and-hold operation, simplifying front-end driver design. Factory calibration trims integral and differential nonlinearity to datasheet limits, removing the iterative software-calibration routine required by many older 16-bit SAR parts and accelerating design-in. Typical applications include industrial process control front ends, multi-channel data-acquisition boards, weigh-scale and strain-gauge instrumentation, motor-control current-sense digitizers, and portable test instruments that need a proven 16-bit ADC on a single 5 V rail. The high throughput and parallel interface make it well suited to closed-loop control where deterministic conversion latency is essential. Design consideration: the input driver amplifier must settle the switched-capacitor input within the acquisition window at full throughput, and the parallel interface traces should be length-matched and series-terminated to avoid digital bus coupling into the analog input. A 100 nF ceramic decoupling cap must be placed within a few millimeters of the supply pins, with bulk capacitance at the regulator output. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement but do not replace the Analog Devices datasheet.
AD976ABNZ - 16-Bit 200 kSPS ADC | Analog Devices
The Analog Devices AD976ABNZ is a 16-bit, single-input successive-approximation analog-to-digital converter with a 200 kSPS throughput rate, operating from a single 5 V supply and packaged in a 28-pin plastic DIP. It combines an ADC core, internal reference, sample-and-hold circuitry, and on-chip clock into a complete parallel-output data-conversion solution. An ADC is an interface IC that converts a continuously varying analog voltage into a digital code suitable for processing by a microprocessor, DSP, FPGA, or control system. The AD976 belongs to the data-converter hierarchy: ADC → SAR ADC → data-converter IC → interface semiconductor. A successive-approximation converter uses an internal DAC and comparator to determine each output bit, making it practical for medium-speed instrumentation and control applications. The principal characteristics of the AD976A include 16-bit resolution, 200 kSPS throughput, parallel digital output, and single 5 V operation. The AD976 version of the family operates at 100 kSPS, while the AD976A doubles the throughput to 200 kSPS. The AD976/AD976A architecture also supports selectable internal or external reference arrangements and includes factory calibration for offset, gain, SNR, and THD performance. Because this is a bipolar converter, input signal range and reference voltage determine the available full-scale span. The parallel interface exposes the conversion result directly on dedicated data pins, avoiding serial-interface overhead at higher sample rates. An on-chip clock reduces the number of external timing components, while the integrated reference supports standalone operation when the required accuracy and range suit the application. Typical uses include industrial process measurement, instrumentation, waveform analysis, laboratory data acquisition, medical monitoring, and embedded control systems. The 200 kSPS rate is suitable for capturing slowly varying or moderate-bandwidth analog signals rather than high-frequency communications waveforms. Its 28-pin through-hole package also favors legacy industrial and laboratory equipment where DIP sockets and through-hole assembly remain practical. Designers should use the manufacturer pin-description and connection tables when assigning the parallel data, clock, reference, analog-input, and supply pins. Input-source impedance, acquisition time, reference stability, digital-bus timing, and analog grounding can affect conversion accuracy. Because a SAR ADC requires sufficient acquisition time, the sampling network must settle to the required accuracy before each conversion begins. This product page combines the family specifications, verified distributor identification, package details, replacement analysis, and practical design guidance to provide a concise engineering reference for the AD976ABNZ. The 28-pin DIP construction and parallel 16-bit interface remain its defining features when evaluating legacy data-acquisition upgrades.
AD976ABR - 16-Bit 200 kSPS ADC | Analog Devices | SOIC-28
Analog Devices AD976ABR is a high-speed, low-power 16-bit successive-approximation ADC with a 200 kSPS throughput rate, a single 5 V supply, and a 28-lead SOIC package. It provides one analog input, a parallel digital interface, selectable internal or external 2.5 V reference, and an on-chip clock. The AD976A is manufactured using Analog Devices' proprietary BiCMOS process, combining high-performance bipolar circuitry with CMOS logic. An ADC converts an analog voltage into a digital value. Within the broader semiconductor hierarchy, the AD976ABR is a data-converter IC and specifically a successive-approximation, or SAR, ADC. SAR converters repeatedly compare the sampled input with a reference and internal bit weights, making them well suited to instrumentation, industrial measurement, communications, and control systems where accurate conversion and predictable parallel data output are required. Key features include 16-bit resolution, 200 kSPS throughput, operation from one 5 V supply, a factory-calibrated analog section, and a high-speed parallel interface. The input range extends to 10 V maximum according to the verified distributor listing, while the converter offers a choice of internal or external 2.5 V reference. Its specified linearity error is 0.0031%, and maximum power dissipation is listed as 100 mW. The AD976A architecture combines a switched-cap ADC core, an accurate reference, and an on-chip clock. Factory calibration and testing address signal-to-noise ratio, total harmonic distortion, offset, gain, and linearity. This integration reduces the number of external timing and reference components required in a 16-bit acquisition circuit while preserving a direct, parallel data path. Typical applications include digital instrumentation, industrial process measurement, communications equipment, data acquisition, control systems, and precision test equipment. The AD976ABR is particularly suitable where a 200 kSPS conversion rate and 16-bit code width must coexist with a conventional 5 V analog supply and parallel digital interface. Designers should follow the manufacturer's pinout and application guidance for input-range, reference, clock, and bypass-capacitor configuration. Input settling, source impedance, analog-noise placement, digital-interface timing, and thermal performance require PCB attention because acquisition accuracy depends on the complete analog signal path rather than conversion resolution alone. This product record consolidates the verified manufacturer and distributor data, distinguishes available family alternatives, and adds practical selection and design guidance that are not presented as a single manufacturer-datasheet summary.
AD976ABRZ - 16-Bit 200 kSPS ADC | Analog Devices
The Analog Devices AD976ABRZ is a 16-bit successive-approximation analog-to-digital converter with a 200 kSPS throughput rate, operating from a single 5 V supply and housed in a 28-pin SOIC package. It accepts one analog input, provides an internal 2.5 V reference, and supports selectable internal or external reference operation. An ADC is an interface IC that converts a continuously varying analog voltage into a numeric code for processing by a microcontroller, DSP, FPGA, or industrial controller. The AD976A belongs to the high-speed ADC category and uses a switched-capacitor, successive-approximation architecture. Its parallel data interface makes it suitable for systems that sample rapidly and require direct acquisition-data access without a serial-interface converter. The converter provides 16-bit resolution, 200 kSPS throughput, single 5 V operation, and an input range of ±10 V. Its internal 2.5 V reference and choice of internal or external reference support flexible board-level signal-chain designs. Maximum power dissipation is listed as 100 mW, making the device suitable for compact industrial, instrumentation, communications, and embedded control systems. At the heart of the AD976A is a switched-capacitor successive-approximation conversion stage with a parallel output interface. Successive-approximation ADCs generally provide a practical balance among resolution, conversion throughput, power consumption, and implementation complexity. The 16-bit code represents the analog input with a quantization step determined by the selected input range and reference voltage. Typical uses include industrial process monitoring, instrumentation, communications equipment, data-acquisition systems, and embedded control platforms. The 200 kSPS rate is suitable for sampling waveforms and transducers whose useful bandwidth is well below the converter's Nyquist limit. System designers should also account for acquisition time, input settling, source impedance, reference stability, digital-interface timing, and analog filtering when defining overall measurement accuracy. For PCB implementation, use the manufacturer's pin-description table to assign the 28 SOIC connections, connect bypass capacitors close to the supply and reference pins, and keep the analog input route away from high-current digital and clock-return paths. The wide-body SOIC package offers more routing space than a narrow-body variant, but careful grounding and decoupling remain necessary to preserve the converter's full 16-bit performance. This product record combines the manufacturer's converter specifications, package information, sourcing guidance, application context, and engineering notes in one place. It also distinguishes confirmed device characteristics from parameters that require consultation of the AD976 datasheet, helping engineers plan acquisition boards, compare interfaces, and qualify replacements without relying on incomplete distributor summaries.
AD976ACN - 16-Bit 200 kSPS ADC | Analog Devices | DIP-28
The Analog Devices AD976ACN is a 16-bit, 200 kSPS successive-approximation analog-to-digital converter in a 28-lead DIP package. It operates from a single 5 V supply, supports selectable internal or external 2.5 V reference options, and provides a high-speed parallel output interface. These characteristics place the device in the ADC hierarchy as a data-conversion IC for precision signal acquisition. An ADC converts an analog input voltage into a numeric code suitable for processing by a microprocessor, DSP, FPGA, or other digital system. The AD976 family uses a switched-capacitor, BiCMOS implementation that combines bipolar input circuitry with CMOS logic. This architecture supports the AD976A variant at 200 kSPS while retaining the resolution and sampling rate needed for instrumentation, industrial control, communications, and embedded measurement systems. Key characteristics include 16-bit resolution, 200 kSPS throughput for the AD976A, single 5 V operation, and a parallel data interface. The converter also includes an on-chip clock and allows the 2.5 V reference to be selected from internal or external sources. An external reference can support repeatable measurement systems that require independent reference control or tighter calibration across multiple converters. The parallel interface exposes conversion results directly as digital bits rather than routing each sample through a serial link. This architecture can simplify connection to older digital buses and parallel FPGA logic, although the 28-pin package requires adequate PCB routing space and careful treatment of analog and digital return paths. The converter’s 100 mW maximum power dissipation figure is particularly relevant when designing compact systems with limited thermal capacity. Typical uses include process monitoring, waveform capture, instrumentation, communications receivers, and industrial data-acquisition systems. For these applications, the key design trade-off is interface flexibility versus board area: parallel output supports high-rate data transfer but requires more traces and pins than a serial ADC. The AD976ACN is therefore most appropriate when existing digital logic is parallel and the 28-pin through-hole footprint is available. For layout, place input, reference, and decoupling connections according to the pin-description and typical-application diagrams in the manufacturer datasheet. A stable supply and reference arrangement are essential because gain, offset, and code accuracy depend on those nodes remaining quiet. This page also organizes sourcing, replacement, and application guidance so engineers can evaluate the AD976ACN against same-package conversion options before committing a board layout.
AD976ACNZ - 16-Bit 200 kSPS ADC | Analog Devices
The Analog Devices AD976ACNZ is a single-input, 16-bit successive-approximation analog-to-digital converter with a sampling rate of 200 kSPS. It operates from a single 5 V supply, accepts an analog input range of 4.75 V to 5.25 V for its supply, and is packaged in a 28-pin plastic DIP. The converter uses a parallel data interface and is designed for moderate-speed signal acquisition. An ADC is an analog-to-digital converter, a semiconductor that samples a continuous analog voltage and converts it into a numeric value. Within the broader hierarchy of data-acquisition ICs, converters are classified by resolution, conversion architecture, sampling rate, and interface type. The AD976A combines a 16-bit resolution with a successive-approximation architecture, making it suitable for systems that require more precision than 12-bit converters but do not need the throughput of high-speed flash or pipeline converters. Principal features include 16-bit resolution, one analog input, 200 kSPS throughput, a parallel interface, and single 5 V operation. The 200 kSPS rate provides 5 microseconds per conversion, making the device appropriate for industrial instrumentation, communications, test equipment, control systems, and other acquisition paths operating in the hundreds-of-kilohertz range. A parallel interface also provides a direct connection to digital logic or a suitable data-acquisition interface. The AD976A is the 200 kSPS member of the AD976 family, while the original AD976 is specified at 100 kSPS. Successive-approximation conversion uses a capacitor array, comparator, and successive comparison stages to determine the digital result. This architecture is well suited to precision measurements where conversion latency, resolution, and power efficiency matter more than very high sampling throughput. Typical uses include digitizing process-control signals, sampling transducers, capturing low-frequency waveforms, conditioning sensor outputs, and feeding parallel ADC data into digital signal processing or control logic. The device can support instrumentation systems in which a sensor signal is buffered, scaled to the converter's input range, sampled, and then processed as a 16-bit value. For layout and assembly, place the input and reference circuitry close to the converter and follow the pin-description table in the Analog Devices AD976 datasheet when assigning every 28-pin DIP connection. Keep analog and digital return currents separated where practical, provide stable supply bypassing, and verify signal settling before the sampling instant. The plastic DIP package is suitable for conventional through-hole assembly and prototype or legacy equipment. This product page combines the AD976ACNZ electrical identity, package and ordering information with practical selection guidance, a comparison table, and design-focused implementation notes. It also highlights the important distinction between the 200 kSPS AD976A and the 100 kSPS original AD976 when evaluating system timing and replacement decisions.
AD976ACR - 16-Bit 200 kSPS SAR ADC | Analog Devices
Analog Devices AD976ACR is a 16-bit successive-approximation analog-to-digital converter with a 200 kSPS throughput rate, single 5 V supply operation, and a 28-lead SOIC package. The device uses a switched-capacitor BiCMOS architecture and provides a parallel data interface for high-speed signal acquisition. It supports either an external reference or an on-chip 2.5 V reference, includes an on-chip clock, and is specified for a maximum power dissipation of 100 mW. A successive-approximation ADC, or SAR ADC, is a type of data-converter IC that determines each digital output code through a sequence of internal comparisons. The AD976ACR belongs to the SAR ADC hierarchy, which sits within analog-to-digital converters and broader data-conversion and semiconductor categories. Its parallel output architecture reduces the external multiplexing burden commonly associated with serial-interface converters, making it suitable for systems that sample waveforms or process digitized measurements at high sample rates. The principal features include 16-bit resolution, a 200 kSPS conversion throughput, single 5 V operation, low power dissipation, and a high-speed parallel interface. The switched-capacitor internal architecture supports the conversion speed specified for the AD976A family. Designers can select an external precision reference or use the internal 2.5 V reference, depending on calibration, drift, and accuracy requirements. An on-chip clock reduces the need for an external timing component when the converter's internal clock is suitable for the application. The AD976 and AD976A family combines a 16-bit switched-capacitor SAR ADC with parallel data outputs in 28-lead DIP, SSOP, and SOIC packages. The AD976A reaches 200 kSPS, while the original AD976 is specified at 100 kSPS. This distinction is important when comparing exact orderable MPNs because a package match alone does not guarantee identical throughput, temperature grade, or lead-finish characteristics. The AD976ACR ordering code specifically denotes the Analog Devices AD976A configuration in a 28-lead SOIC package. Typical applications include industrial instrumentation, communications equipment, data-acquisition systems, medical or laboratory measurement equipment, and embedded DSP signal processing. The 200 kSPS rate is suitable for sampling control and sensor signals when the system requires higher throughput than the 100 kSPS AD976 configuration. The parallel interface can connect directly to suitable digital buses or input stages, although signal conditioning, reference design, and acquisition timing still require careful validation. The main design consideration is preserving the accuracy of a 16-bit conversion while controlling noise, reference stability, and digital-interface timing. Designers should account for the specified 100 mW maximum power dissipation when designing the 5 V supply and board layout. Input and reference routing should minimize noise coupling, while clock and data timing must meet the requirements of the selected parallel interface. The manufacturer datasheet remains the authoritative source for pinout, timing, electrical limits, and application details. This page consolidates the verified manufacturer and distributor information for AD976ACR, distinguishes the 200 kSPS AD976A from the 100 kSPS AD976, records verified sourcing links, and identifies the limited availability of true pin-compatible alternatives. It also provides practical application guidance and transparent data gaps rather than presenting unverified specifications or packaging variants as drop-in replacements.