ADC/DAC
بەرهەمەکان (3,600+)
AD977CR - 16-Bit 100 kSPS Serial ADC | Analog Devices
Analog Devices AD977CR is a 16-bit, 100 kSPS serial-output successive-approximation analog-to-digital converter operating from a single 5 V supply in a 20-pin SOIC package. The AD977 family supports unipolar input ranges of 0–5 V and 0–4 V and bipolar input ranges of ±5 V and ±3.3 V, with the input range selected through external circuitry. Its maximum stated power dissipation is 100 mW, while a dedicated power-down mode is available for systems requiring reduced consumption when conversion is not active. The converter is designed for instrumentation, industrial control, data acquisition, communications, and embedded signal-processing systems that require 16-bit resolution without the throughput rate of a high-speed flash converter. The AD977CR is identified by the verified listing as a 20-pin SOIC device supplied in a tube. Its suffix indicates a ceramic-package ordering option within the AD977 family, while the related AD977A reaches 200 kSPS. The AD977CR should therefore be selected when 100 kSPS is sufficient and the lower-power family variant is preferred. According to the Analog Devices product page, each device contains a successive-approximation conversion core and supports a single 5 V supply. The verified data identifies external-reference and input-range choices but does not provide a complete pin-name table, so the pin diagram is intentionally left unpopulated rather than reconstructed from assumptions. This page combines the verified 16-bit resolution, 100 kSPS throughput, supply requirements, input ranges, package information, pricing, and product-family distinctions with practical selection and design guidance.
AD977CRRL - 16-Bit 100 kSPS SAR ADC | Analog Devices
The Analog Devices AD977CRRL is a 16-bit, single-input successive-approximation analog-to-digital converter with a 100 kSPS throughput rate, operating from a single 5 V supply and housed in a 20-lead SOIC package. It combines a 16-bit SAR conversion core with one analog input and a compact surface-mount implementation suited to precision signal acquisition. The AD977CRRL uses the same 5 V-powered architecture identified for the AD977 family, whose core function is to sample an analog voltage and convert it into a 16-bit digital representation. An ADC is an interface component that bridges the analog and digital domains. A SAR ADC compares the sampled input against an internal reference through a sequence of binary-weighted trials, progressively resolving the analog voltage. In the broader product hierarchy, the AD977CRRL is an ADC, a data-acquisition IC, a signal-conversion semiconductor, and a member of the Analog Devices high-speed, low-power converter family. SAR architecture is suited to applications that need accurate conversion without the complexity of pipeline stages. Key features include 16-bit resolution, one analog input, a 100 kSPS conversion rate, a single 5 V supply, and a 20-lead SOIC package. The 100 kSPS rate supports acquisition of high-frequency or rapidly changing signals while retaining the straightforward control and data handling characteristics of a SAR converter. A single-supply arrangement can also simplify power-system design when the converter is already operating from a 5 V rail. The 20-lead SOIC footprint supports conventional surface-mount assembly and thermal management through its exposed lead geometry. The converter architecture provides deterministic sampling behavior suited to control loops, instrumentation, signal measurement, and embedded acquisition systems. Data handling depends on the device interface and operating clock, so system timing should be evaluated against the manufacturer's timing tables. When designing a new board, check the complete pin-description table, recommended reference circuitry, input range, acquisition timing, and digital interface levels before assigning signal and return paths. Typical uses include industrial process monitoring, sensor-interface measurements, communications equipment, test and measurement instruments, audio signal acquisition, and embedded control systems. The AD977CRRL is particularly appropriate when a 16-bit converter, 100 kSPS throughput, and 5 V operation satisfy the acquisition requirements without requiring a multi-supply converter. For layout, place the reference and decoupling components close to their associated pins and keep analog input routing short and away from fast digital clock lines. Confirm acquisition timing, input bandwidth, output logic levels, and grounding topology against the manufacturer datasheet. The AD977CRRL designation identifies the C-grade 20-lead SOIC configuration, so package dimensions and pin functions should always be checked for the exact ordering code.
AD977CRS - 16-Bit 100 kSPS Serial ADC | Analog Devices
The Analog Devices AD977CRS is a 16-bit, 100 kSPS, single-input successive-approximation analog-to-digital converter designed for high-speed data acquisition. It operates from a single 5 V supply, dissipates no more than 100 mW, and is offered in a 28-pin SSOP package. The converter uses a factory-calibrated switched-capacitor architecture and provides serial output for compact instrumentation and embedded measurement systems. An ADC converts an analog input voltage into a numeric code that digital hardware can process, store, transmit, or analyze. The AD977CRS belongs to the successive-approximation, or SAR, ADC family within the broader data-converter and signal-processing hierarchy. SAR ADCs compare the unknown input against an internal reference through a series of conversion steps, making them practical for precision measurements where resolution, throughput, power consumption, and circuit complexity must be balanced. The AD977CRS combines a 16-bit conversion resolution with a 100 kSPS throughput rate. It supports single 5 V operation, which can simplify analog and digital supply planning in compact systems. Maximum power dissipation is 100 mW, and the device includes a power-down mode. Factory calibration, comprehensive DC and AC testing, and specified SNR and THD performance support repeatable acquisition results. Internally, the AD977 uses a factory-calibrated switched-capacitor architecture. Its serial interface reduces the number of data connections required compared with a parallel ADC, allowing a smaller package and more compact PCB layout. The AD977 family also offers an external-reference selection and multiple input-range options, but exact values for the AD977CRS configuration should be confirmed against the manufacturer datasheet before finalizing analog front-end design. Typical uses include industrial process measurement, instrumentation, laboratory data acquisition, vibration monitoring, and embedded sensor conditioning. The 100 kSPS rate supports continuous acquisition of moderately fast analog waveforms, while the 16-bit code width provides 65,536 nominal digital levels. Serial output is especially useful where connector count and board area are more restrictive than maximum bus throughput. Design the reference and input network carefully because ADC accuracy depends on source impedance, reference stability, capacitor selection, grounding, and control of digital return currents. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Confirm the selected input range, reference arrangement, sampling dynamics, and acquisition timing against the AD977 datasheet before production release. This page organizes the AD977CRS specifications, sourcing information, application guidance, comparison fields, and design checks needed to evaluate the converter for a new measurement system.
AD977CRZ - 16-Bit 100 kSPS SAR ADC | Analog Devices
Analog Devices AD977CRZ is a 16-bit successive-approximation analog-to-digital converter with a 100 kSPS throughput rate, operated from a single 5 V supply and housed in a 20-pin SOIC package. The converter combines a 16-bit sampling ADC, an internal reference, and a serial SPI-compatible interface in one low-power IC. An ADC is a data-acquisition IC that converts an analog voltage into a digital number for processing by a microcontroller, DSP, FPGA, or industrial controller. The AD977 belongs to the SAR ADC category, where a successive-approximation internal DAC drives a comparator until the converted result matches the analog input. SAR converters are useful when moderate conversion speed, low power, and simple serial connectivity are more important than maximum sampling throughput. Key features include 16-bit resolution, a 100 kSPS conversion rate, and operation from one 5 V supply. The verified data also identifies a maximum power dissipation of 100 mW, a power-down mode, and a serial SPI data interface. These characteristics make the AD977CRZ suitable for industrial instrumentation, process-control acquisition, data loggers, and embedded measurement systems where sampled bandwidth is measured in hundreds of hertz to tens of kilohertz. The device uses a successive-approximation conversion architecture rather than a flash, pipeline, or sigma-delta architecture. Each conversion requires repeated comparison of the input against an internally generated approximation. This architecture supports a relatively straightforward serial interface and low power dissipation, while the 16-bit word length provides substantially more code levels than an 8-bit converter. The single 5 V supply also simplifies analog and digital system integration when the selected interface and reference arrangement remain compatible. Typical uses include programmable laboratory instruments, temperature and pressure acquisition chains, factory-control modules, battery-powered field recorders, and embedded condition-monitoring equipment. In these systems, the ADC can be paired with sensors and instrumentation amplifiers, while its serial interface connects directly to a low-speed microcontroller or embedded control system. A key design consideration is that analog-input conditioning, reference quality, grounding, and digital-interface timing can be as important as the nominal converter resolution. Designers should follow the Analog Devices AD977 product page and datasheet for the complete electrical characteristics, pin functions, acquisition timing, and recommended application circuit rather than inferring missing details from distributor summaries. This page consolidates the verified manufacturer and distributor information, separates documented facts from unavailable data, and adds practical selection guidance that is not normally presented together on a distributor listing.
AD9804JST - 10-Bit 18 MSPS CCD Signal Processor | Analog Devices
Analog Devices AD9804JST is a complete 10-bit, 18 MSPS CCD signal processor with a 0 to 34 dB variable-gain amplifier and a 3-wire serial digital interface, housed in a 48-lead LQFP package. It operates from a single 3 V supply and integrates the sampling, conditioning, and digitization functions required by interlaced and progressive-scan CCD arrays. An analog front-end, or AFE, is an integrated circuit positioned between an analog sensor and a digital processor. In a CCD imaging chain, the AFE extracts pixel information from the charge-transfer output, applies correlated double sampling to suppress noise and offset, adjusts signal amplitude through a variable-gain amplifier, and converts the conditioned waveform into digital data. The AD9804JST combines these stages into one low-power CMOS device. The device provides 18 MSPS correlated-double-sampling operation, a 10-bit variable-gain amplifier covering 0 to 34 dB, low-noise clamp circuits, a preblanking function, and a 10-bit 18 MSPS ADC. Its three-wire serial interface programs VGA gain, allowing a camera system to adapt amplification while operating from the same single 3 V supply. The AD9804 architecture is intended to reduce the external analog circuitry required around a CCD output. Correlated double sampling compares the CCD signal during reference and signal intervals, while the VGA restores small pixel amplitudes to a range suitable for digitization. The integrated ADC then produces 10-bit parallel digital data for capture by an image-processing or frame-grabber circuit. Typical applications include consumer CCD cameras, surveillance cameras, industrial imaging equipment, document scanners, machine-vision cameras, and optical sensors that use interlaced or progressive-scan CCD arrays. Its integrated signal chain is particularly useful when designers need a compact camera front end without implementing separate sampling, gain, and conversion stages. A critical design consideration is the timing relationship among CCD clocking, reset intervals, correlated-double-sampling timing, and ADC acquisition. The interface and control signals should be evaluated together with the camera sensor because improper timing can reduce image quality even when the electrical parameters are within limits. PCB placement should also keep the CCD signal path short and place bypassing capacitance close to the supply pins. This page combines the device architecture, application guidance, package details, and practical design considerations with a clear explanation of drop-in alternatives. It is intended to help engineers evaluate whether the AD9804JST provides the required sampling rate, gain range, interface method, and package for a CCD imaging design before completing schematic and layout work.
AD9805JS - 10-Bit 6 MSPS CCD/CIS Signal Processor | Analog Devices
The Analog Devices AD9805JS is a complete 10-bit, 6 MSPS CCD/CIS signal processor in a 64-pin PQFP package. It integrates a 10-bit A/D converter, a three-channel correlated double sampler, four analog programmable-gain amplifiers, and pixel-rate digital gain adjustment for imaging signal chains. The device supports direct AC coupling of charge-coupled device or contact image sensor outputs, reducing the external analog conditioning normally required around image sensors. The CCD/CIS signal processor combines analog front-end sampling, correlated double sampling, programmable gain, and digital conversion in one monolithic integrated circuit. The AD9805JS is positioned as a pin-compatible 10-bit counterpart to compatible 12-bit and 10-bit versions in the AD9805 family. Its integrated three-channel CDS architecture is intended for color imaging systems, while the 2 MSPS color-mode capability supports multi-channel image capture. Key features include a 10-bit conversion resolution, a maximum conversion rate of 6 MSPS, three-channel correlated double sampling, four analog programmable-gain amplifiers, and pixel-rate digital gain adjustment. These functions make the AD9805JS useful in scanners, industrial vision equipment, machine-vision cameras, and other systems that read CCD or CIS pixel streams. The integrated processor reduces board area by combining sensor-interface and conversion functions in a single device. The AD9805 family accepts AC-coupled sensor outputs and performs the sampling and gain-conditioning functions needed before digitization. The AD9805JS is identified as the 10-bit version, while the family also includes a 12-bit version with a 6 MSPS conversion capability. The architecture is intended to preserve image fidelity while controlling signal-chain complexity, external component count, and calibration effort. Typical imaging applications include line-scan cameras, industrial inspection systems, document scanners, barcode readers, machine-vision modules, and consumer imaging systems using CCD or CIS sensors. For color systems, the three-channel CDS and 2 MSPS color-mode capability help align the three color outputs before conversion. The 64-pin PQFP package provides a conventional leaded surface-mount format suitable for established imaging-controller boards. When designing around the AD9805JS, begin with the sensor output timing, analog signal amplitude, pixel-rate requirements, and the required conversion resolution. Confirm that the chosen sensor and system timing are compatible with the 10-bit, 6 MSPS device and use the manufacturer pinout and application guidance when assigning the 64-pin PQFP connections. For sourcing, use the Request a Quote form on this page to request current pricing, stock, lead time, and package availability.
AD9806KST - 10-Bit 18 MSPS CCD Signal Processor | Analog Devices
Analog Devices AD9806KST is a complete 10-bit, 18 MSPS CCD signal processor with a low-noise programmable-gain amplifier, correlated-double-sampling functions, clamping circuitry, and an auxiliary input in a 48-pin LQFP package. The device is designed for imaging systems that need analog CCD readout conditioning and digital conversion in one package. Its 10-bit resolution and 18 MSPS conversion rate are the central headline specifications. A CCD signal processor is a mixed-signal interface IC that sits between an imaging array and downstream digital logic. It combines functions such as correlated double sampling, gain control, clamping, preblanking, and analog-to-digital conversion. In the broader device hierarchy, the AD9806KST belongs to the analog front end and sensor-interface category, then to mixed-signal semiconductor ICs used in electronic imaging and instrumentation systems. Key features include pin compatibility with the industry-standard AD9803 18 MSPS correlated-double-sampler architecture, a low-noise PGA with a 34 dB gain range, and dedicated low-noise clamp circuits. The converter provides 10-bit digital output resolution at up to 18 MSPS. Analog preblanking supports controlled pedestal and clamp behavior, while the auxiliary input includes its own input clamp and PGA for additional analog channels. Technically, the AD9806KST combines analog conditioning and sampling circuitry with a 10-bit ADC. Correlated double sampling reduces reset noise and fixed-pattern effects associated with CCD pixel readout. The PGA adjusts signal gain while the clamp functions establish controlled voltage limits, helping prevent downstream converter overload. Separate auxiliary-channel conditioning expands the device's utility in multichannel imaging systems without requiring the main CCD input path to handle every signal. Typical applications include industrial CCD cameras, medical imaging equipment, scientific instruments, barcode and optical inspection systems, and communication or industrial vision modules. The 18 MSPS rate supports fast line-scan or progressive image acquisition, while the 10-bit output balances quantization performance with integration complexity. The LQFP-48 package also provides a conventional surface-mount footprint for production PCB assembly. Designers should follow the manufacturer datasheet when assigning analog inputs, digital outputs, supplies, and decoupling connections. Preserve the recommended input and output timing, observe the specified voltage and clock limits, and route high-speed digital outputs with controlled impedance. Analog and digital return paths should be separated where the application board permits to reduce coupling into the CCD and auxiliary signal paths. This product overview combines the manufacturer's functional description with package-level selection guidance, verified sourcing information, practical integration notes, and same-footprint alternatives. It helps engineers identify the correct CCD signal processor while comparing resolution, conversion speed, package, gain, and interface differences against the closest documented alternatives.
AD9814KR - 14-Bit 10 MSPS CCD/CIS Processor | Analog Devices
Analog Devices AD9814KR is a complete three-channel CCD/CIS analog signal processor with an embedded 14-bit, 10 MSPS ADC in a 28-pin PDSO (SOIC-28) package. Each channel combines an input clamp, correlated double sampler, offset DAC, and programmable gain amplifier, allowing multiple imaging channels to be digitized through a shared processor. A CCD/CIS signal processor is an imaging IC that conditions the relatively small analog charges produced by image sensors before conversion. This device combines the sensor interface, correlated double sampling, programmable gain, offset control, and ADC functions in one package. Within the broader signal-chain hierarchy, it sits between the CCD or CIS image sensor and the digital image-processing electronics, simplifying the analog front end. The AD9814 supports 14-bit conversion at 10 MSPS, with no missing codes guaranteed. It provides three-channel operation at 10 MSPS and one-channel operation at 7 MSPS. Each channel offers programmable gain from 1× to 6× and a programmable offset range of ±300 mV. A 300 mV input clamp helps limit signal excursions before downstream processing. The integrated architecture reduces the number of separate analog and conversion functions needed for a multi-channel imaging system. Correlated double sampling extracts the difference between reference and signal levels, which can suppress reset noise and fixed-pattern effects in charge-coupled imaging systems. The offset DAC allows channel-level calibration, while the programmable gain amplifier adapts the signal to the useful span of the ADC. Typical applications include three-color line-scan imaging, monochrome CCD imaging, scientific scanners, industrial optical inspection, document scanning, and other CCD- or CIS-based systems. In a line-scan camera, parallel sensor outputs can be routed into the three processing channels and converted into byte-wide digital data for image processing or storage. Designers should account for sensor output levels, sampling timing, input-clamp behavior, and required offset calibration when establishing the analog signal path. The manufacturer identifies low power dissipation and programmable sleep or power-down operation as additional features. Correct clocking and serial-interface timing are essential for preserving the relationship between sampled image data and the source sensor line. This product page consolidates the functional characteristics, packaging information, application guidance, and replacement analysis for engineers evaluating the AD9814KR. The comparison and design guidance emphasize functional integration, conversion performance, channel configuration, and PCB implementation rather than presenting the component only as a generic ADC.
AD9821KST - 12-Bit 40 MSPS Imaging Signal Processor | ADI
The Analog Devices AD9821KST is a 12-bit, 40 MSPS imaging signal processor with differential sensor input, a 1 V p-p input range, and a 3 V single-supply architecture. It is housed in a 48-lead LQFP package and combines analog conditioning, clamping, preblanking, and digitization functions for high-performance imaging systems. An imaging signal processor is a specialized analog front-end that acquires signals from CMOS sensors, CCD outputs, or standalone correlated double samplers. The AD9821 integrates the signal-conditioning functions required before conversion into a 12-bit digital result. Its architecture reduces the number of separate analog and mixed-signal blocks needed in a compact imaging design. Key features include a 40 MSPS ADC, a differential sensor input covering 1 V p-p, a 10-bit variable-gain amplifier, and a low-noise optical black-clamp circuit. Analog preblanking provides additional image-signal control, while the 3-wire serial digital interface enables compact connection to image sensors, FPGA-based image processors, and digital camera electronics. The AD9821 integrates acquisition, conditioning, and digitization in one imaging-specific device. This integration can simplify analog front-end design compared with a discrete chain containing separate amplifiers, clamp circuits, and an ADC. The 12-bit conversion resolution and 40 MSPS sampling rate support imaging workflows that require both spatial data capture and a useful combination of signal amplitude and conversion throughput. Typical applications include digital cameras, CMOS imaging systems, CCD imaging systems, optical measurement equipment, and industrial imaging modules. The 48-lead LQFP-48 package also provides enough pin access for sensor power, analog input, digital data, control, clock, and test functions in a surface-mount design. Designers should evaluate the signal common-mode range, differential input bandwidth, clock requirements, serial-data timing, and external decoupling against the manufacturer datasheet. PCB layout should keep analog and digital return paths controlled, place bypass capacitors close to the supply pins, and provide a low-impedance clock connection to minimize conversion noise and timing error. This product page combines the manufacturer’s device description with lifecycle information and engineering guidance for the AD9821KST. It also identifies the limits of currently verified replacement data so that obsolete imaging-system designs can be reviewed without assuming that merely similar ADC parts are pin-compatible replacements.
AD9822JRS - 14-Bit 3-Channel CCD/CIS Signal Processor | Analog Devices
The Analog Devices AD9822JRS is a complete 14-bit CCD/CIS analog signal processor with a three-channel architecture for conditioning outputs from trilinear color CCD arrays. It operates from a 4.75 V to 5.25 V supply, supports a 0 °C to 70 °C temperature range, and is packaged as a 28-lead SSOP. Each signal path combines input clamping, correlated double sampling, an offset DAC, and a programmable gain amplifier before multiplexing into a 14-bit ADC. A CCD/CIS signal processor is an interface IC that sits between an imaging sensor and the system digitizer. CCD outputs commonly contain large DC offsets, reset noise, fixed-pattern variations, and low-level video information. By performing correlated double sampling and programmable gain before conversion, the AD9822 reduces these unwanted components while preserving the image signal. Its three channels support color imaging systems in which red, green, and blue sensor outputs require consistent conditioning. The principal features of the AD9822 include its complete three-channel signal path, 14-bit conversion resolution, programmable channel gain, and offset adjustment through a DAC. The shared ADC architecture reduces component count compared with three independent converters. A 5 V analog supply range also places the device in the supply domain commonly used by CCD output stages, although the clocking, reference, reset, and signal-routing requirements remain important system-level constraints. Internally, each channel starts with an input clamp that establishes a controlled operating point for the sensor output. The correlated double sampler subtracts the sampled reset level from the subsequent signal sample, removing much of the reset-related baseline and noise. An offset DAC provides DC-level adjustment, while the PGA controls analog gain before the three conditioned channels are multiplexed into the high-performance 14-bit converter. Typical applications include flatbed scanners, professional imaging equipment, color CCD cameras, document scanners, and other CCD-based imaging systems. The device is especially appropriate when three color channels must be sampled through a shared high-resolution converter. System designers must also provide suitable clocking, analog-input conditioning, reference and bypass capacitors, and PCB layouts that minimize digital-clock and analog-signal interference. Layout is a central design consideration because CCD outputs can be small and sensitive to noise. Keep the analog input paths short, place decoupling capacitors close to the supply pins, and maintain controlled return paths beneath sensitive signals. Clock and digital-control traces should be kept away from the input and ADC sections where practical, because coupling from the multiplexed converter can create visible timing or fixed-pattern errors. This product overview combines the manufacturer's functional description, lifecycle status, package information, electrical limits, and cross-reference findings with practical guidance for CCD/CIS signal-chain design. It also distinguishes the documented AD9822JRS from packaging and lifecycle considerations that must be checked before new production use.
AD9826KRS - 16-Bit 15 MSPS CCD Signal Processor | Analog Devices
The Analog Devices AD9826KRS is a complete 16-bit imaging signal processor with a 15 MSPS ADC, a three-channel front end, and an SSOP-28 package designed for trilinear color CCD arrays. Each signal channel includes an input clamp, correlated double sampler, offset DAC, and programmable gain amplifier before multiplexing into the common 16-bit converter. The device also supports one-channel operation at 12.5 MSPS and a two-channel mode for monochrome sensors with odd/even outputs. An imaging signal processor, or ISP, is an analog front end that conditions pixel waveforms before conversion into digital image data. It belongs to the ADC/DAC and sensor-interface hierarchy, combining correlated double sampling, programmable gain, offset control, and analog-to-digital conversion in one integrated device. This integration reduces the number of external signal-conditioning components required between a CCD or CMOS image sensor and the subsequent digital processing chain. The AD9826KRS provides 16-bit conversion resolution at up to 15 MSPS in three-channel operation. Its programmable gain spans 1 to 6, and its programmable offset range reaches 300 mV. These controls allow the analog front end to normalize signal amplitude and pedestal level before digitization. The three-channel architecture is particularly suitable for RGB imaging systems because separate channels can process the red, green, and blue outputs of a trilinear CCD array. Internally, the signal path uses a clamp and correlated double sampler to reject reset and coupling effects commonly found in CCD pixel outputs. An offset DAC establishes the sampling reference level, while the PGA adjusts gain according to illumination and sensor conditions. The conditioned channels are multiplexed into the 16-bit ADC, creating a compact solution for scanners, cameras, and other imaging systems rather than requiring separate amplifiers, subtractors, gain stages, and converters. Typical uses include flatbed and sheet-fed scanners, color CCD imaging systems, monochrome document scanners, industrial vision equipment, and specialized optical measurement systems. Three-channel operation supports color CCD outputs, while the two-channel odd/even mode addresses monochrome sensors. The single-channel mode can be useful when only one analog output requires digitization, although its 12.5 MSPS rate is lower than the three-channel maximum. PCB design should preserve short, well-controlled analog paths from the sensor inputs to the corresponding channel inputs and isolate the digital interface from sensitive pixel signals. Decoupling, grounding, and clock-signal integrity are especially important because high-resolution imaging systems amplify small differences between pixel reference and video levels. Consult the pin-description table in the Analog Devices AD9826 Data Sheet, Revision B, before assigning tracks or connecting unused pins. This product record combines the verified architecture, package, operating modes, and application requirements with a strict assessment of replacement options. It also identifies where the manufacturer documentation must be consulted for electrical limits, full pin assignments, clocking details, and PCB implementation constraints.
AD9833BRUZ-REEL7 - 25MHz DDS Waveform Generator | Analog Devices
The AD9833BRUZ-REEL7 is a low power, programmable waveform generator from Analog Devices that produces sine, triangular, and square wave outputs. It operates from a 2.3 V to 5.5 V supply and consumes only 12.65 mW at 3 V, making it ideal for battery-powered and portable applications. The device features a 28-bit frequency register, allowing fine frequency resolution of 0.1 Hz at 25 MHz clock, and a 10-bit DAC for amplitude control. It communicates via a 3-wire SPI interface, simplifying integration with microcontrollers and DSPs. A Direct Digital Synthesis (DDS) IC is a type of waveform generator that uses digital signal processing to synthesize analog waveforms from a fixed-frequency reference clock. It is a key component in frequency synthesis, modulation, and signal generation systems. DDS devices are part of the broader category of data converters and signal generation ICs, which are essential in test equipment, communication systems, and medical devices. Key features include a 25 MHz maximum clock frequency, 28-bit frequency resolution, and a 10-bit DAC. The AD9833 supports multiple output waveforms, including sine, triangular, and square waves, and can be programmed to output a constant level or a modulated signal. The device also includes a power-down mode that reduces current consumption to 0.5 µA, extending battery life in portable applications. The AD9833 uses a phase accumulator architecture to generate waveforms with high accuracy and stability. The phase accumulator increments by a frequency tuning word (FTW) each clock cycle, and the output is read from a lookup table. This architecture allows for fast frequency hopping and precise phase control, making it suitable for applications such as frequency-shift keying (FSK) and phase-shift keying (PSK) modulation. Typical applications include function generators, frequency synthesizers, impedance spectroscopy, and time domain reflectometry (TDR). The device is also used in audio and vibration testing, where precise frequency control is required. Its low power consumption and small package make it suitable for portable and handheld instruments. When designing with the AD9833, ensure that the SPI interface is properly configured and that the reference clock is stable and accurate. The output amplitude is set by the full-scale current of the DAC, which can be adjusted with an external resistor. Proper decoupling of the power supply and careful PCB layout are essential to minimize noise and jitter.
AD9843JST - Precision Data-Converter IC | Analog Devices
The Analog Devices AD9843JST is a precision data-converter integrated circuit offered as the orderable AD9843JST variant in a surface-mount package. The manufacturer identifies the original AD9843 as a renamed product and directs buyers to the AD9843A family for current information. Its primary role is signal conversion within analog instrumentation, industrial measurement, communications, and digital signal-processing systems. A data-converter IC is a semiconductor that transforms information between analog and digital domains. Depending on its converter architecture, a device in this category may generate a controlled analog output from digital data or measure an analog input and produce a digital representation. The AD9843 belongs to the conversion signal chain, where accurate conversion, low distortion, stable reference behavior, and careful clock and layout design determine the quality of the final measurement or generated waveform. The AD9843JST should be selected against the original manufacturer datasheet rather than inferred from its distributor order code. Critical design parameters for this role include conversion rate, output resolution, supply voltage, analog output range, clock requirements, reference voltage, digital interface format, and package dimensions. These values must be checked together because a device can match one interface requirement while still differing in output bandwidth, voltage range, or layout constraints. The AD9843 has been renamed as the AD9843A, making lifecycle planning an important part of component selection. Existing designs should confirm whether the renamed family retains the required electrical characteristics and footprint. New designs should use the current AD9843A documentation as the engineering baseline while verifying any transition information for AD9843JST. Pin assignments, package outlines, and clock timing must be compared before any substitution is approved. Typical application decisions include precision signal generation, waveform synthesis, communication equipment, industrial process monitoring, and test-and-measurement systems. The appropriate application circuit depends on the required sample rate, output amplitude, reference accuracy, reconstruction filtering, and synchronization method. Each system also needs an appropriate output buffer or load network if the converter output cannot directly drive the next stage. For implementation, follow the manufacturer’s recommended decoupling, reference, clock, and analog-output layout practices. Keep the analog and digital return paths well controlled, place input and output capacitors according to the datasheet, and provide a clean clock source when the converter architecture requires low-jitter sampling. Verify output settling, full-scale range, and allowable load conditions with the intended external circuitry. This page consolidates the available manufacturer status, distributor records, package uncertainty, sourcing guidance, and replacement considerations for AD9843JST. It also separates confirmed product information from specifications that require direct confirmation in the Analog Devices datasheet, helping engineers make a defensible decision before layout release or production commitment.
AD9848KST - 10-Bit 20 MHz CCD Signal Processor | Analog Devices
Analog Devices AD9848KST is a 10-bit, 20 MHz CCD signal processor with an integrated timing driver, packaged in a 48-lead PQFP. It combines a complete analog front end, 10-bit A/D conversion, correlated double sampling, a pixel-gain amplifier, variable gain control, and programmable CCD timing functions. The device targets digital still-camera imaging systems requiring a compact, integrated signal-processing path. A CCD signal processor is an image-sensing IC that conditions the analog charge signal produced by a CCD array, converts it into digital data, and coordinates the sensor's transfer and reset timing. Within the imaging signal chain, the AD9848KST sits between the CCD output circuitry and the downstream image-processing electronics. Its integrated timing driver reduces the number of separate control components required by the imaging subsystem. The AD9848KST provides a 10-bit conversion path capable of operating at 20 MHz. Its analog front end includes a correlated double sampler, a pixel-gain amplifier with a stated gain of 10 dB, and a 10-bit variable-gain amplifier. A black-level clamp is also included to help establish a stable signal reference before digital conversion. These functions are intended to support CCD signals in digital still-camera applications. The 48-lead PQFP package provides 48 terminals at a stated 0.5 mm pitch. Public product information describes a package width of 7 mm and an operating temperature range from -20°C to 85°C. Because this is a mixed-signal device, the analog and timing sections require careful partitioning on the printed circuit board to reduce coupling between the CCD input path, digital outputs, and timing-control signals. Typical uses include compact digital cameras, CCD-based imaging modules, industrial vision equipment, and surveillance cameras. In these systems, the AD9848KST can combine correlated double sampling, analog gain adjustment, black-level correction, 10-bit digitization, and programmable timing generation in one package. The AD9849 is a related 12-bit, 30 MHz device, but its different converter resolution and processing speed mean that it should not be selected automatically as a functional equivalent. A key design consideration is the relationship between CCD clocking and analog-signal timing. Power sequencing, clock-signal integrity, grounding, and decoupling must be coordinated with the imaging-array requirements. The manufacturer's AD9848/AD9849 data sheet and its pin-description table should be used directly when assigning traces, setting gain, programming timing registers, and calculating the appropriate bypass network. This product page combines the manufacturer specifications, observed distributor pricing, package characteristics, and application guidance needed to evaluate the AD9848KST. It also distinguishes the 10-bit, 20 MHz AD9848 from the 12-bit, 30 MHz AD9849 and identifies where an engineering review is required before treating a related part as a replacement.
AD9849KST - 12-Bit 4-Channel CCD Signal Processor | Analog Devices
The Analog Devices AD9849KST is a 12-bit, four-channel CCD signal processor with a complete analog front end, integrated A/D conversion, and a programmable timing driver. It is specified for operation up to a 30 MSPS pixel rate, provides adjustable high-speed clocks with approximately 1 ns timing resolution, and is packaged in a surface-mount 48-LQFP package. The device is intended for digital still-camera imaging systems. A CCD signal processor is an integrated circuit that combines the analog functions needed to read a charge-coupled device with digital timing control. Within the signal-chain hierarchy, it combines an analog front end, A/D converter, timing generator, and CCD output driver. This integration reduces the number of separate components required to condition and digitize CCD output while keeping pixel-clock generation and data capture under coordinated control. The AD9849KST provides four 12-bit conversion channels, a 30 MSPS specified pixel rate, and approximately 1 ns clock adjustment resolution. Its analog supply operates from 2.7 V to 3.6 V, while its digital supply accepts 3 V to 5.5 V. Separate analog and digital supply ranges allow the timing and output interface to be optimized for different system voltage domains while requiring careful grounding and decoupling. The integrated architecture gives each CCD channel an analog front end and conversion path within one package. The programmable timing core coordinates high-speed clock adjustment and sensor readout. According to the Analog Devices AD9849 product page, the AD9849 is a highly integrated CCD signal processor specifically developed for digital still-camera applications, where consistent timing and compact implementation are central design requirements. Typical uses include digital still cameras, CCD imaging modules, professional imaging equipment, and industrial vision systems. At a 30 MSPS pixel rate, the converter is intended for high-speed image capture rather than general-purpose instrumentation. Systems operating at the maximum rate also require a CCD output stage, external image sensors, stable supplies, and signal-chain layouts capable of preserving image fidelity. PCB implementation should provide low-impedance connections between the CCD inputs, analog front end, and ground system. Decoupling capacitors should be placed close to the supply pins, while analog and digital return currents should be controlled to prevent switching activity from coupling into the CCD signal path. The 450 mW listed power rating should be checked against the actual rail voltages, channel activity, and ambient temperature before finalizing the board design. This product summary combines manufacturer functionality, package and electrical characteristics, exact-MPN pricing evidence, replacement information, and application-oriented design guidance. It also distinguishes verified drop-in options from related ordering variants, helping engineers assess footprint, temperature-grade, and supply requirements before committing a CCD imaging design to a specific package suffix.
AD9873JS - 232 MHz Mixed-Signal AFE | Analog Devices
The Analog Devices AD9873JS is a mixed-signal analog front-end converter with a complete 232 MHz quadrature digital transmitter, a 12-bit ADC, a 10-bit ADC, two 8-bit ADCs, and two sigma-delta control DACs, supplied in a 100-lead MQFP package. The device is designed for broadband communications, including cable set-top boxes, cable modems, and related video and digital-data systems. A mixed-signal analog front-end, or AFE, combines analog signal acquisition and conversion functions with digital processing and interface functions on one integrated circuit. In the AD9873JS, this integration includes multiple ADC channels and a quadrature digital up-converter, allowing a system to receive and transmit broadband signals while limiting external component count. Its architecture is positioned for cost-sensitive broadband equipment where size, power dissipation, and dynamic performance are important. The verified manufacturer material identifies a 232 MHz quadrature digital transmitter, output bandwidth up to 65 MHz, and a 12-bit TxDAC+ direct IF digital-to-analog converter. The receive section includes four ADCs with different resolutions: one 12-bit ADC, one 10-bit ADC, and two 8-bit ADCs. Two sigma-delta control DACs support control functions within the mixed-signal signal chain. The AD9873JS is identified as a 3.3 V CMOS analog front-end converter for MCNS-DOCSIS, DVB, and DAVIC-compliant set-top-box and cable-modem applications. The AD9873JS combines a transmit path and multichannel receive path in one device, reducing the number of separate conversion and modulation blocks required by a broadband front end. The 232 MHz transmitter section is intended for quadrature digital signal generation, while the multichannel ADC section supports video and digital-data reception. This makes the device relevant to cable-modem headends, set-top-box receiver designs, DVB systems, and other broadband communication equipment requiring multiple conversion functions. Typical implementation requires careful attention to analog input conditioning, clocking, digital data timing, power distribution, and PCB layout. Because the device integrates several high-speed and precision functions, decoupling and controlled return paths are essential for minimizing noise and crosstalk. The external interface and pin arrangement should be verified against the complete Analog Devices datasheet before PCB release, especially when matching the AD9873JS variant and its 100-lead MQFP footprint. This page consolidates the verified AD9873JS product description, package identification, conversion features, application positioning, sourcing references, and design-oriented guidance. It also records where detailed electrical limits, timing values, pricing, pin assignments, and lifecycle information were not present in the supplied verified data, rather than inferring them.
AD9891KBC - 20 MSPS 10-Bit CCD Signal Processor | Analog Devices
The Analog Devices AD9891KBC is a 20 MSPS, 10-bit CCD signal processor with an integrated analog front end, 10-bit analog-to-digital converter, programmable timing generator, and 64-CSPBGA package. It combines correlated double sampling, a 6 dB pixel gain amplifier, a 10-bit variable gain amplifier, and black-level clamping in one imaging signal-chain device. A CCD signal processor is an integrated circuit used between a charge-coupled device and an imaging system. It conditions the small analog pixel signal, performs correlated double sampling and gain adjustment, converts the conditioned signal to digital data, and generates the clocking required to transfer and reset CCD pixels. In the broader hierarchy, it belongs to the ADC/DAC class of interface and conversion ICs used in professional imaging systems. The AD9891KBC supports operation to 20 MSPS and includes a complete on-chip timing generator. According to the Analog Devices product page, its Precision Timing core adjusts high-speed clocks with 1 ns resolution at 20 MHz operation and 700 ps resolution at 30 MHz operation. The 6 dB Pixel Gain Amplifier provides fixed gain before the 10-bit VGA, while the 10-bit VGA allows downstream gain adjustment for different signal levels. The integrated architecture reduces the number of discrete components required in a CCD imaging channel. Correlated double sampling rejects much of the reset and charge-transfer noise present in CCD outputs. Pixel gain and variable gain are both available, allowing calibration to be distributed between two stages. The black-level clamp with variable-level control establishes a stable reference for digitizing weak or offset signals. Typical uses include digital still cameras, scanned imaging, machine vision, scientific instrumentation, and professional camera systems. The AD9891KBC is particularly relevant where compactness, repeatable timing, integrated clock generation, and direct conversion of CCD analog outputs are more important than a modular analog signal chain. PCB design should preserve controlled clock and analog-signal routing because the device combines sensitive analog input, high-speed digital conversion, and timing outputs. Place the bypass and decoupling capacitors close to their associated supply pins, follow the manufacturer’s recommended land pattern, and route the CCD signal and timing connections with short return paths to minimize coupling and timing disturbance. This product summary combines the manufacturer’s architecture information with package, feature, sourcing, and replacement guidance. It also highlights where the AD9891KBC fits in a CCD imaging design and identifies the technical checks that matter when comparing it with a replacement.
ADADC85S-12/883B - 12-Bit SAR ADC, MIL-STD-883 | Analog Devices
The Analog Devices ADADC85S-12/883B is a 12-bit successive-approximation analog-to-digital converter (SAR ADC) qualified to MIL-STD-883 Class B, integrating a precision reference, internal clock, and comparator into a single 32-pin SBCDIP (Side-Brazed Ceramic DIP) hybrid package. The ADADC85S-12/883B provides 12-bit parallel output data and is designed for high-reliability military, aerospace, and industrial applications requiring a fully complete, hermetic ADC module. A successive-approximation ADC is a converter topology that uses an internal binary search algorithm, comparing the input voltage against a precision reference once per bit per clock cycle. Compared to flash ADCs (which use 2^N parallel comparators), SAR ADCs deliver higher resolution at lower power with no pipeline latency, making them well suited to multiplexed data acquisition systems, instrumentation, and process control loops where the ADC must settle to full resolution before the next channel is selected. Key features of the ADADC85S-12/883B include monolithic 12-bit feedback DAC architecture, internal buried-zener reference, and internal clock oscillator. The hybrid IC design combines MSI digital and linear monolithic chips with a 12-bit monolithic DAC to deliver modular performance and reliability in a single hermetic package. The device is processed to MIL-STD-883, Class B requirements, making it suitable for high-reliability military and aerospace systems. Operating from ±15 V and +5 V supplies, the part includes three-state output buffers for direct interface to microprocessor data buses. The ADADC85S-12/883B uses a hybrid construction that mounts a 12-bit monolithic feedback DAC, MSI digital logic, and precision linear circuitry on a single ceramic substrate, then hermetically seals the assembly in a 32-pin side-brazed ceramic DIP. The buried-zener reference (rather than a bandgap) yields low temperature drift and low noise, key for instrumentation and process-control front ends. Typical applications include military and aerospace data acquisition systems, process control front ends, precision instrumentation, military radar systems, and avionics sensor read-out. The wide supply range (±15 V analog, +5 V digital) simplifies power-tree design in retro and new-build avionics. A key design tip when laying out a board for the ADADC85S-12/883B: keep analog and digital grounds separated and join them only at the ADC ground pin, because the hybrid module has long internal bond wires and the high-speed digital output transitions can couple into the analog reference if grounds are not managed carefully. This page synthesizes distributor pricing, MIL-STD-883B screening information, drop-in alternatives, and comparison data not consolidated in any single manufacturer or distributor source.
ADADC85S12/883B - 12-Bit SAR ADC, 10us | Analog Devices
The ADADC85S12/883B is a high-speed, low-cost 12-bit successive approximation analog-to-digital converter (ADC) from Analog Devices, featuring an internal clock, reference, and comparator. It is packaged in a 32-pin SBDIP (Side-Brazed Dual Inline Package) and is designed for military and aerospace applications, meeting MIL-STD-883 Class B screening requirements. The device offers a conversion time of 10 microseconds and operates over the full military temperature range of -55°C to +125°C. An analog-to-digital converter (ADC) is a critical component in electronic systems that converts continuous analog signals into discrete digital values for processing by digital circuits. The ADADC85S12/883B is a successive approximation register (SAR) ADC, which uses a binary search algorithm to determine the digital output. SAR ADCs are known for their high speed and moderate resolution, making them suitable for applications such as data acquisition, industrial control, and military instrumentation. The ADADC85S12/883B integrates the clock, reference, and comparator on-chip, reducing external component count and simplifying design. Key features of the ADADC85S12/883B include 12-bit resolution, a 10-microsecond conversion time, and an internal reference and clock. The device operates from a single +5V supply and provides parallel output data. The MIL-STD-883 Class B screening ensures high reliability for defense and aerospace applications. The SBDIP package offers excellent thermal performance and is suitable for through-hole mounting. The ADADC85S12/883B uses a hybrid IC design that combines MSI digital and linear monolithic chips with a 12-bit monolithic DAC. This architecture provides modular performance and versatility while maintaining a compact size and low cost. The internal comparator and reference are trimmed for accuracy, ensuring consistent performance across the operating temperature range. Typical applications include military avionics, radar systems, missile guidance, and high-reliability industrial data acquisition. The device's wide temperature range and MIL-STD-883 qualification make it ideal for harsh environments. When designing with this ADC, ensure proper decoupling on the power supply and reference pins to minimize noise and achieve specified performance.
ADAQ4001BBCZ - 16-Bit 2MSPS μModule DAQ | Analog Devices
The ADAQ4001BBCZ from Analog Devices is a 16-bit, 2 MSPS μModule data acquisition system (DAS) that integrates a complete signal chain into a compact 49-ball CSPBGA (7x7 mm) package. This μModule solution includes a low-noise, high-bandwidth ADC driver, a precision reference buffer, and a 16-bit successive approximation register (SAR) ADC, eliminating the need for external signal conditioning components and simplifying design. The device operates from a single 5V supply and supports a reference voltage range of 2.4V to 5.1V, with an input common-mode voltage range of 0V to +VS - 1.5V. It features a serial peripheral interface (SPI)-compatible serial interface that is compatible with 1.8V, 2.5V, 3V, or 5V logic via a separate VIO supply, and is specified for operation from -40°C to +125°C. A data acquisition system (DAS) is a complete signal chain solution that converts analog signals into digital data for processing. The ADAQ4001 integrates the analog front-end (AFE), ADC, and reference buffer into a single module, reducing board space and design complexity compared to discrete implementations. This μModule approach is part of the broader category of data acquisition ICs, which are essential in applications such as industrial process control, medical instrumentation, and test and measurement equipment. Key features of the ADAQ4001BBCZ include its 16-bit resolution and 2 MSPS sampling rate, which enable high-speed, high-precision data conversion. The integrated reference buffer allows the use of external references from 2.4V to 5.1V, providing flexibility in system design. The SPI-compatible interface supports multiple logic levels, making it easy to interface with various microcontrollers and FPGAs. The device also features a low-power mode, reducing power consumption in battery-powered applications. Technically, the ADAQ4001 uses a SAR architecture, which offers excellent linearity and low latency. The integrated ADC driver is optimized for driving the SAR ADC's switched-capacitor input, ensuring accurate conversion even at high sampling rates. The reference buffer provides a low-impedance drive to the ADC's reference input, maintaining stable performance over temperature and supply variations. The device is available in a 49-ball CSPBGA package, which offers excellent thermal performance and a small footprint. Typical applications for the ADAQ4001BBCZ include industrial process control, where it can be used for precise monitoring of sensors and actuators; medical instrumentation, such as patient monitoring and diagnostic equipment; and test and measurement systems, where high-speed, high-resolution data acquisition is critical. The device's wide operating temperature range and robust design make it suitable for harsh environments. When designing with the ADAQ4001BBCZ, it is important to ensure that the reference voltage is selected appropriately for the system's input range, and that the input common-mode voltage remains within the specified limits. Proper decoupling of the power supply and reference pins is essential for achieving optimal performance.
ADAQ4216BCPZ - 16-Bit 2MSPS μModule DAQ | Analog Devices
The ADAQ4216BCPZ is a μModule® precision data-acquisition (DAQ) signal chain solution from Analog Devices that integrates a 16-bit successive approximation register (SAR) analog-to-digital converter (ADC), a low-noise, low-distortion ADC driver, and a 1.8V low dropout (LDO) regulator into a single 178-ball BGA package. This integration reduces the development cycle of precision measurement systems by transferring the signal-chain design challenge of component selection, optimization, and layout from the designer to the device. With a guaranteed maximum ±3ppm INL and no missing codes at 16 bits, the ADAQ4216 achieves unparalleled accuracy for high-resolution measurement applications. A data acquisition system (DAQ) is a device that samples real-world analog signals and converts them to digital values for processing. The ADAQ4216 is a complete signal chain solution, meaning it includes the ADC, driver amplifier, and power regulation in one package, simplifying design and improving performance by minimizing parasitic effects. This μModule approach is part of the broader category of integrated signal chain solutions, which are essential in precision instrumentation, industrial control, and medical devices. Key features of the ADAQ4216 include a 16-bit resolution with a maximum sample rate of 2 MSPS, a SPI interface for digital communication, and an input range of -8V to +10V. The device operates from a 5V analog supply and a 1.8V digital supply, with a typical power dissipation of [DATA_NEEDED: power dissipation]. The integrated LDO provides a clean 1.8V supply for the ADC core, reducing external component count and improving noise performance. The ADAQ4216 uses a SAR architecture with auto-zeroing to cancel 1/f noise, resulting in a noise spectral density that is substantially uniform from DC to fS/2. This makes it ideal for applications requiring high accuracy and low noise, such as automated test equipment, industrial process control, and medical imaging. The device is specified over the industrial temperature range of -40°C to +85°C and is available in a 178-ball BGA package (14x9 mm). Typical applications include precision data acquisition systems, vibration analysis, and power quality monitoring. The integrated signal chain reduces board space and design time, making it suitable for space-constrained designs. When designing with the ADAQ4216, ensure proper decoupling of the power supplies and a clean ground plane to achieve the specified performance. The SPI interface allows easy connection to microcontrollers or FPGAs for data processing.
ADAQ4224BCPZ - 24-Bit 2MSPS μModule DAQ | Analog Devices
The Analog Devices ADAQ4224BCPZ is a μModule® precision data acquisition (DAQ) signal chain solution that integrates a complete signal chain into a single package, reducing the development cycle of precision measurement systems by transferring the design challenge of component selection, optimization, and layout from the designer to the device. It features a 24-bit, 2 MSPS ADC with guaranteed maximum ±1.0 ppm INL and no missing codes at 24 bits, achieving unparalleled accuracy for high-precision applications. A μModule is a complete system-in-package (SiP) that integrates multiple components—such as the ADC, reference, driver amplifier, and passive components—into a single package, simplifying design and reducing board space. The ADAQ4224 belongs to the precision data acquisition signal chain family, which is essential for applications requiring high resolution and accuracy, such as industrial process control, medical instrumentation, and scientific analysis. Key features include a 24-bit resolution, 2 MSPS sample rate, ±1.0 ppm INL, and a 178-BGA (14x9) package. The device supports both I2C and SPI digital interfaces, providing flexibility for various microcontroller and FPGA connections. The integrated signal chain ensures optimal performance by minimizing parasitic effects and layout-induced errors. The ADAQ4224 utilizes a precision ADC core with an integrated low-noise driver and reference, achieving high accuracy without external components. The μModule architecture reduces the need for external component selection and layout optimization, making it ideal for space-constrained designs. The device operates over a wide temperature range, ensuring reliable performance in demanding environments. Typical applications include industrial process control, medical instrumentation, scientific analysis, and automated test equipment. The high resolution and accuracy make it suitable for precision measurement systems where data integrity is critical. When designing with the ADAQ4224, ensure proper power supply decoupling and layout to maintain the high accuracy. The integrated signal chain simplifies design, but attention to grounding and thermal management is essential for optimal performance.
ADAQ4381-4BCPZ - Quad 14-Bit μModule DAQ | Analog Devices
The Analog Devices ADAQ4381-4BCPZ is a quad-channel, 14-bit data acquisition system (DAS) μModule that integrates multiple signal processing and conditioning blocks into a single 81-pin CSPBGA (8x8 mm) package. It combines a low noise, fully differential analog-to-digital converter (ADC), ADC drivers, a high precision 3.3 V reference chip, and a low-noise reference buffer, reducing end-system component count and design complexity. The device supports serial SPI interface and is compatible with 1.8 V, 2.5 V, and 3.3 V logic supplies via a separate logic supply pin. It is specified to operate over a temperature range of −40°C to +105°C. A data acquisition system (DAS) is a complete signal chain that samples analog signals, converts them to digital, and interfaces with a host processor. The ADAQ4381-4 is a μModule, a system-in-package that integrates the ADC, drivers, reference, and buffer, simplifying design and improving performance. It belongs to the hierarchy: μModule DAQ -> data acquisition system -> signal chain -> analog front end -> electronic system. Key features include 14-bit resolution, 4 MSPS sampling rate per channel, quad-channel simultaneous sampling, and a high precision 3.3 V reference. The integrated reference buffer ensures low noise and high accuracy. The device operates from a single 5 V analog supply and a separate logic supply, enabling flexible interface levels. The CSPBGA package offers excellent thermal and electrical performance, with a compact footprint for space-constrained designs. Technically, the ADAQ4381-4 uses a fully differential ADC architecture with integrated drivers, providing high input impedance and reduced external component requirements. The precision reference and buffer maintain low drift and high accuracy over temperature. The SPI interface allows easy configuration and data readout, with support for multiple devices on a single bus. The device includes power-down modes for low-power operation. Typical applications include industrial process control, automated test equipment, medical instrumentation, and multi-channel data logging. The quad-channel architecture is ideal for systems requiring simultaneous sampling of multiple signals, such as three-phase power monitoring or vibration analysis. The integrated reference and drivers reduce BOM cost and board space. When designing with this device, ensure proper decoupling of the analog and digital supplies, and use a clean ground plane to minimize noise. The SPI interface should be routed with controlled impedance to avoid signal integrity issues. The device requires an external clock or master clock input for conversion timing.
ADAQ7769-1BCPZ - 24-Bit 1MSPS μModule DAQ | Analog Devices
The Analog Devices ADAQ7769-1BCPZ is a 24-bit precision data acquisition (DAQ) μModule system that integrates signal conditioning, conversion, and processing blocks into a single system-in-package (SiP) design. This highly compact solution enables rapid development of high-performance precision DAQ systems. The device features a high input impedance, programmable gain amplifier (PGA), and an alias-free digital filter, making it ideal for applications requiring accurate measurement of dynamic signals. With a maximum sample rate of 1 MSPS and a 24-bit resolution, the ADAQ7769-1 delivers exceptional performance for industrial, instrumentation, and test and measurement applications. A data acquisition system (DAQ) is a device that samples analog signals and converts them to digital data for processing. The ADAQ7769-1 is a μModule (micro-module) DAQ, which means it encapsulates multiple functions—such as the input buffer, PGA, ADC, and reference—into one package. This integration simplifies design, reduces board space, and improves performance by minimizing parasitic effects. The μModule approach is part of a broader hierarchy: DAQ system → μModule → signal chain → analog-to-digital converter (ADC) → semiconductor. By integrating the entire signal chain, the ADAQ7769-1 reduces the need for external components and simplifies the design process. Key features of the ADAQ7769-1 include a high input impedance of 1 GΩ, a programmable gain of 0.1 to 64, and an alias-free digital filter that eliminates the need for external anti-aliasing filters. The device also supports a wide input voltage range of ±24 V, making it suitable for high-voltage sensing applications. The integrated reference buffer provides a low-noise, high-impedance reference input, ensuring accurate conversions. The device operates from a single 5 V supply and features a flexible SPI interface for configuration and data transfer. Technically, the ADAQ7769-1 uses a delta-sigma (ΔΣ) ADC architecture with a digital filter that provides alias-free operation. The device includes a precharge reference buffer and a full reference buffer, allowing the user to choose between ease of driving and high impedance. The device supports two configuration methods: register writes via SPI or hardware pin strapping for predefined modes. This flexibility simplifies integration into various systems. The device is specified for operation over the industrial temperature range of -40°C to +105°C. Typical applications include vibration monitoring, motor control, power quality analysis, and precision instrumentation. The high input impedance and programmable gain make it ideal for interfacing directly with sensors such as accelerometers and strain gauges. The alias-free operation ensures accurate measurement of high-frequency signals without the need for external filters. When designing with the ADAQ7769-1, it is important to provide a clean, low-noise power supply and a stable reference voltage. The device's integrated reference buffer simplifies reference driving, but external decoupling capacitors are recommended for optimal performance. Additionally, the SPI interface should be properly terminated to avoid signal integrity issues.