بەرهەمەکان (970+)

DS3231N/DIP - Precision I2C RTC with TCXO | Maxim Integrated
DS3231N/DIP

DS3231N/DIP - Precision I2C RTC with TCXO | Maxim Integrated

The Maxim Integrated DS3231N/DIP is a precision I2C real-time clock with an integrated temperature-compensated crystal oscillator, crystal, and battery input, supplied in a 16-pin DIP package. It maintains real-time clocking across a 2.3 V to 5.5 V operating supply range. Its stated accuracy is ±2 ppm from 0°C to +40°C and ±3.5 ppm from -40°C to +85°C. A real-time clock is a clock-and-timing integrated circuit that maintains date and time independently of the system processor. The I2C real-time clock hierarchy connects this device to serial real-time clocks, clock-and-timing ICs, and broader power-management and embedded-control systems. The DS3231N/DIP combines a crystal oscillator with an integrated temperature-compensated crystal and digital compensation to reduce timing drift caused by temperature variation. The principal feature of the DS3231N/DIP is its integrated TCXO and crystal, which support accurate timekeeping without a separate discrete crystal. Its I2C interface provides a straightforward connection to a host processor, while the integrated battery input allows the clock and calendar to continue operating when the main supply is removed. The stated ±2 ppm accuracy from 0°C to +40°C is the principal selection criterion for precision timekeeping designs. Within its broad operating-temperature range, accuracy changes to ±3.5 ppm from -40°C to +85°C. This distinction matters when comparing the component across industrial temperature environments rather than only at room temperature. The 2.3 V to 5.5 V supply range supports both lower-voltage embedded systems and conventional 5 V logic environments, although interface voltage compatibility must be checked against the host controller. Typical uses include industrial embedded controllers, data-acquisition equipment, access-control systems, instrumentation, network appliances, and battery-backed logging platforms. The integrated TCXO and crystal simplify the oscillator design, while the I2C interface reduces the number of host GPIO connections required for calendar and alarm functions. Systems requiring a larger I2C bus can place the device on the same bus as other compatible peripherals. When laying out a circuit, use the manufacturer's pin-description and connection tables to assign VCC, ground, I2C, interrupt, and battery-related connections. Confirm pull-up voltage and logic levels against the host supply. Route the backup-battery connection according to the manufacturer's guidance and verify backup-current behavior when the main rail is unavailable. This page consolidates the manufacturer's product information, distributor records, package details, application guidance, and practical replacement considerations. It also identifies where the available cross-reference records do not establish additional same-package drop-in parts, helping engineers avoid treating merely similar RTC devices as direct board-level replacements.

RFQ پەیوەندی
DS3231S# - Accurate I2C RTC with TCXO | Analog Devices
DS3231S#

DS3231S# - Accurate I2C RTC with TCXO | Analog Devices

The Analog Devices DS3231S# is a highly accurate I2C real-time clock with an integrated temperature-compensated crystal oscillator, crystal, and battery backup, supplied in a 16-SOIC package. It operates from 2.3 V to 5.5 V and maintains timekeeping when the main supply is interrupted. The integrated TCXO and crystal provide accurate timekeeping without requiring an external crystal and load-capacitor design. A real-time clock is a clock-and-calendar integrated circuit that retains date and time information while a system is unpowered. The RTC belongs to the timekeeping and clock-and-timing hierarchy within semiconductor electronics. Unlike a general-purpose microcontroller timer, the DS3231S# is designed to maintain calendar information, provide a programmable square-wave output, and interface through a two-wire I2C bus. The DS3231S# combines a battery-backed RTC, an integrated temperature-compensated crystal oscillator, and an integrated crystal in one package. Its operating-voltage range of 2.3 V to 5.5 V supports both 3.3 V and 5 V systems. The two-wire interface reduces the number of host-controller connections required for timekeeping, while the integrated backup-battery path allows continued operation during a main-power loss. According to the Analog Devices manufacturer product page, the device is a low-cost, extremely accurate I2C real-time clock with an integrated TCXO and crystal. This integration supports compact designs for industrial controllers, embedded products, data-acquisition equipment, and consumer electronics. The device also provides a 32.768 kHz square-wave output according to the manufacturer datasheet, allowing it to serve as a timebase or clock source for additional system functions. DS3231S# is appropriate when calendar accuracy, backup timekeeping, and a compact integrated crystal matter more than implementing a software-disciplined oscillator. Designers should provide the required decoupling and maintain suitable routing around the integrated crystal and TCXO. Because the verified source material does not provide a complete pin-by-pin mapping or numeric accuracy and temperature-drift tables, those details should be confirmed in the manufacturer datasheet before schematic release. This page combines verified manufacturer and distributor information, structured technical guidance, and a comparison framework for engineers evaluating the DS3231S#. It does not infer missing electrical limits, lifecycle claims, or alternative-device specifications that are absent from the supplied source data.

RFQ پەیوەندی
DS3231S#T&R - I2C RTC with Integrated TCXO | Analog Devices
DS3231S#T&R

DS3231S#T&R - I2C RTC with Integrated TCXO | Analog Devices

Analog Devices DS3231S#T&R is an I2C real-time clock and calendar with an integrated temperature-compensated crystal oscillator (TCXO), crystal resonator, and battery-backup input. It operates from 2.3 V to 5.5 V, uses a 16-pin SOIC package measuring 7.50 mm in width, and is supplied in tape-and-reel packaging. The integrated oscillator is maintained by a crystal and is specified for operation from 0°C to +70°C. A real-time clock is a timekeeping semiconductor that retains calendar date and time information across power interruptions. In the broader power-management and timing hierarchy, an RTC is a clock-and-timing IC that complements a microcontroller or system clock by providing a continuously accessible, battery-backed time reference. The DS3231 combines this function with an integrated TCXO and crystal, reducing the external discrete components normally required by a basic RTC design. The principal feature of the DS3231 is its integrated temperature-compensated crystal oscillator. Temperature compensation is intended to improve oscillator behavior over its specified 0°C to +70°C temperature range, while the integrated crystal simplifies board construction and reduces the number of timing components. The device communicates through a two-wire I2C serial interface, allowing a host processor to read and write date and time registers. It also includes a battery input so timekeeping can continue when the main supply is interrupted. The 2.3 V to 5.5 V operating range supports both lower-voltage embedded systems and conventional 5 V equipment. Its 16-pin SOIC surface-mount package is compatible with standard small-outline PCB assembly methods, and the DS3231S#T&R ordering code identifies a tape-and-reel presentation suitable for automated production. Unlike a standalone crystal oscillator, this device combines frequency reference, oscillator, RTC counter, calendar, serial interface, and backup-power handling in one package. Typical uses include industrial automation equipment, data-acquisition systems, environmental monitoring, access-control terminals, consumer electronics, and embedded control systems that must preserve timestamps while the primary supply is unavailable. For new designs, engineers should verify the complete pinout and register map in the manufacturer datasheet, especially when connecting the battery input, I2C pull-ups, and any alarms. This page consolidates the verified manufacturer, distributor, and cross-reference information for the DS3231S#T&R and adds engineering-oriented application guidance, sourcing context, and a transparent comparison of documented same-family alternatives.

RFQ پەیوەندی
DS3231SN# - I2C RTC with TCXO | Maxim Integrated
DS3231SN#

DS3231SN# - I2C RTC with TCXO | Maxim Integrated

The Analog Devices Inc./Maxim Integrated DS3231SN# is an extremely accurate I2C real-time clock and calendar with an integrated temperature-compensated crystal oscillator (TCXO) and crystal, supplied in a 16-pin SOIC package. The verified source identifies a 2.3 V to 5.5 V supply range, a 32.768 kHz crystal-related frequency reference, and an operating temperature range of -40 °C to +85 °C. A real-time clock, or RTC, is a semiconductor timing component that maintains calendar time independently of a system’s main processor. The DS3231SN# combines the RTC function with an integrated TCXO and crystal, reducing external timing-component count and helping maintain accurate timekeeping across changing temperatures. In a power-management hierarchy, it is an IC oscillator and timekeeping device rather than a power regulator or communications transceiver. The principal verified features are the integrated TCXO and crystal, I2C clock/calendar access, 2-wire serial communication, wide 2.3 V to 5.5 V supply operation, and 16-SOIC packaging. These characteristics suit systems that need seconds, minutes, hours, calendar date, and periodic time events without relying on an external crystal. The integrated TCXO is particularly relevant when maintaining timing accuracy under ambient-temperature variation is more important than using a simple uncorrected crystal oscillator. The DS3231SN# is designed for embedded control, embedded data logging, portable instrumentation, consumer electronics, industrial control, and access-control equipment. In these applications, the host controller reads or writes the RTC through I2C and can use time stamps for event sequencing, display synchronization, scheduled operations, or data-retention workflows. Because the verified distributor description identifies it as an I2C RTC/TCXO device, the design should include appropriate pull-up resistors and confirm the host’s I2C logic levels. When selecting the device, verify the complete pinout and electrical limits in the manufacturer datasheet before layout release. Keep the I2C traces short, provide the required decoupling, and confirm the exact SOIC footprint and pin numbering against the PCB library. The supplied web data does not provide verified pricing tiers, detailed timing accuracy, battery-current values, alarm specifications, or absolute maximum ratings, so those values should be obtained from the manufacturer datasheet. This page combines verified distributor information, the identified DS3231 family functionality, practical integration guidance, and explicit data gaps. It does not invent specifications that were absent from the supplied search results.

RFQ پەیوەندی
DS3231SN#T&R - I2C RTC with TCXO | Analog Devices
DS3231SN#T&R

DS3231SN#T&R - I2C RTC with TCXO | Analog Devices

The Analog Devices DS3231SN#T&R is an I2C real-time clock and calendar with an integrated temperature-compensated crystal oscillator, crystal, and battery backup, operating from 2.3 V to 5.5 V in a 16-pin SOIC package measuring 7.50 mm wide. Its nominal crystal frequency is 0.0320 MHz, and the specified operating-temperature range is -40 °C to +85 °C. The integrated TCXO architecture maintains timekeeping accuracy across temperature changes while preserving a compact solution for systems that require calendar data, alarm handling, and battery-backed time retention. A real-time clock, or RTC, is a clock-and-timing IC that keeps track of seconds, minutes, hours, date, and calendar information independently of a system processor. Within the product hierarchy, an RTC is a timing IC, a semiconductor, and a system-support component. Unlike a basic crystal oscillator, an RTC combines a stable time reference with registers, an I2C control interface, calendar logic, and often backup-power support. This makes it suitable for preserving timestamps when the main supply is interrupted. The DS3231SN#T&R integrates a crystal resonator and temperature-compensated oscillator rather than requiring a discrete crystal and load network. It supports two-wire I2C communication, allowing a host microcontroller to read and program calendar and alarm registers. The available package data identifies a 16-pin, 7.50 mm-wide SOIC surface-mount configuration, while the -40 °C to +85 °C range supports industrial temperature requirements. Battery input allows timekeeping to continue when the primary supply is removed. The internal oscillator is compensated to reduce frequency variation caused by ambient temperature changes. This improves long-term timekeeping consistency compared with an uncompensated crystal oscillator, particularly in applications where the RTC must retain accurate timestamps during intermittent power loss. The 2.3 V to 5.5 V operating range also supports both 3.3 V and 5 V system rails. Exact initial time accuracy, current consumption, alarm resolution, and electrical timing limits are not included in the supplied excerpts and require confirmation from the manufacturer datasheet. Typical uses include industrial control systems, data loggers, metering equipment, network appliances, medical instruments, and embedded products that need a timestamp or calendar across power interruptions. A host processor can initialize the clock once, periodically retrieve time over I2C, and use the RTC as a trusted time source after restart. The integrated oscillator also reduces board area compared with a discrete crystal plus oscillator implementation. The primary design consideration is preserving correct battery-backed operation and power sequencing. The PCB must provide the specified supply and grounding connections, clean I2C routing, and suitable decoupling close to the device. Software should verify time validity after every power restoration instead of assuming that the backup source retained a valid timestamp. Exact capacitor, pull-up, and decoupling recommendations should be taken directly from the manufacturer datasheet. This page consolidates the verified manufacturer and distributor information for the DS3231SN#T&R, combines pricing available as of 2026-10-29 with package and operating-range details, and provides same-package alternatives plus engineering guidance that helps distinguish a true drop-in replacement from merely similar RTC products.

RFQ پەیوەندی
DS90LV110TMTC - 400MHz 1:10 LVDS Distributor | TI
DS90LV110TMTC

DS90LV110TMTC - 400MHz 1:10 LVDS Distributor | TI

Texas Instruments DS90LV110TMTC is a 1-to-10 LVDS data and clock distributor operating up to 400 MHz, with one differential input, ten differential outputs, and a 28-TSSOP package measuring 4.40 mm in body width. The device is designed for high-speed point-to-point distribution of differential clock or data signals while preserving low-noise and low-pulse-width-distortion behavior. An LVDS data and clock distributor is a clock-and-timing interface integrated circuit that accepts one differential input and generates multiple differential outputs. LVDS means low-voltage differential signaling, a method that transmits complementary signals through a balanced pair. In the electronic hierarchy, the DS90LV110TMTC is a clock buffer and fanout driver within clock and timing ICs, and more broadly it belongs to interface and signal-conditioning semiconductors used to distribute high-speed signals across a system. The principal specifications are a 1:10 fanout ratio, a maximum operating frequency of 400 MHz, and ten differential transmitters. Manufacturer descriptions identify support for LVDS, CML, and PECL signaling, while the data paths are fully differential from input to output. The 28-TSSOP package uses a 0.173-inch body length and a 4.40 mm width, making the device suitable for compact backplane, instrumentation, communications, and test-equipment boards. Because all ten outputs are driven from the same differential input, the device centralizes clock distribution and reduces the number of separate fanout stages required. This can simplify synchronization in systems that distribute a common timing reference to multiple endpoints. The differential signal path is intended to generate low noise and limit pulse-width distortion, while a 3.3 V supply supports integration with modern low-voltage digital systems. Typical uses include synchronous backplane clock distribution, parallel data fanout, communication equipment, test-and-measurement systems, and industrial control electronics. A clock-distribution design can place the DS90LV110TMTC near the source clock and route controlled-length differential traces to several destination circuits. For data applications, the one-to-ten relationship allows one incoming differential stream to feed ten receivers when downstream logic requires identical copies. The primary PCB concern is controlled-impedance routing of every LVDS pair. Each differential trace should maintain continuous reference-plane return paths, appropriate pair spacing, and consistent geometry. Input and output topology, termination, and bypass-capacitor placement should follow the manufacturer's recommended layout and application guidance rather than generic point-to-point wiring conventions. This product page combines the confirmed distributor and manufacturer facts with package-focused selection guidance, practical distribution considerations, and verified same-family drop-in comparisons. It helps engineers distinguish the exact 28-TSSOP orderable from related processing and suffix options while preserving the required 1:10 fanout, 400 MHz operation, and differential signaling behavior.

RFQ پەیوەندی
DSA504RT - Rad-Tolerant 6-Output Clock Generator | Microchip
DSA504RT

DSA504RT - Rad-Tolerant 6-Output Clock Generator | Microchip

The Microchip Technology DSA504RT is a radiation-tolerant, low-power, low-jitter six-output programmable clock generator engineered for aerospace and defense applications including spacecraft timing subsystems. It integrates a high-performance fractional-divide Analog Phase-Locked Loop (APLL), two downstream fractional dividers with spread-spectrum capability, two integer dividers, and a configurable cross-point switch that routes any synthesized frequency to any of six outputs. A clock generator (also called a programmable oscillator or frequency synthesizer) is a single-IC timing block that replaces a discrete reference, PLL, divider tree and fanout buffer chain, locking an internal low-jitter VCO/PLL to an external differential or single-ended reference and producing multiple phase-aligned output frequencies from one master source. In the hierarchy of timing components, a clock generator sits between a fixed-frequency crystal oscillator and a full frequency synthesizer, sharing the ASIC integration and configurability of the latter while retaining the deterministic low-jitter behavior of the former. Programmable clock generators are widely used in aerospace, defense, networking, PCIe, and storage systems where multiple precise reference frequencies must be derived from a single hardware reference. Key features of the DSA504RT include jitter performance as low as 200 femtoseconds (12 kHz to 20 MHz integration band), an output frequency range from 0.35 MHz to 662 MHz, support for up to 12 CMOS outputs or 6 differential outputs, PCIe Gen 1 through Gen 7 compliance, and per-output spread-spectrum control. The device accepts an external differential or single-ended reference and uses an I2C/SPI-compatible serial interface for in-orbit reprogramming of output frequencies, divider ratios, and APLL parameters. Two package options are available: a hermetic ceramic CQFP-32 for long-duration deep-space missions and a plastic QFN-28 for less demanding aerospace or ground-based defense applications; the same internal silicon works in both, so a design validated in one package can migrate to the other without reworking the schematic. Typical applications include spacecraft payload data-handling timing, satellite communication payloads, radar and electronic-warfare reference generation, rad-tolerant FPGA reference rails, and PCIe clocking in space-grade single-board computers. Its rad-tolerant process and reprogrammability via I2C/SPI enable in-orbit frequency updates after launch, a critical advantage for missions whose channel plans change after deployment. When designing with the DSA504RT, provide a low-noise reference clock and follow Microchip's recommended PCB layout for the APLL loop filter; misrouted power or reference traces will dominate the jitter budget and defeat the 200 fs performance target. This page synthesizes distributor inventory, same-brand and cross-brand drop-in alternatives, application notes, and design considerations not consolidated on any single manufacturer page.

RFQ پەیوەندی
DSC557-0343FI0 - 100MHz PCIe MEMS Clock Generator | Microchip
DSC557-0343FI0

DSC557-0343FI0 - 100MHz PCIe MEMS Clock Generator | Microchip

The Microchip DSC557-0343FI0 is a crystal-less, single-output PCI Express clock generator that delivers a 100 MHz differential HCSL/LVDS output clock from proven silicon MEMS technology, housed in a 14-pin QFN (2.5 mm × 3.2 mm) package. It is qualified to meet PCIe Gen1, Gen2, Gen3, and Gen4 specifications with 100 ppm total stability over the -40 °C to +85 °C industrial temperature range, and it operates from a 2.25 V to 3.6 V supply. What is a MEMS PCIe clock generator? A clock generator is a timing IC that produces one or more reference frequencies used to synchronize downstream logic such as CPU cores, PHYs, switches, and SerDes lanes. A MEMS (Micro-Electro-Mechanical Systems) clock generator replaces the traditional quartz crystal resonator with a silicon mechanical resonator built on standard CMOS processes, eliminating crystal aging, mechanical shock sensitivity, and the long lead times associated with quartz sourcing. In the PCIe ecosystem, a 100 MHz reference clock with stringent jitter and stability is required to drive PCIe PHYs in endpoints, root complexes, switches, and retimers. Key features include a 100 ppm total frequency stability across temperature, low additive PCIe-compliant jitter, an Output Enable (OE) pin for power sequencing, HCSL or LVDS compatible differential outputs with a 52 % typical duty cycle, and supply voltage tolerance suitable for 3.3 V rails common in server, storage, and embedded designs. The 14-pin QFN package is 77 % smaller than the equivalent 16-pin TSSOP option, simplifying layout in space-constrained boards. Architecturally, the device combines an on-chip MEMS resonator with a fractional-N PLL and an HCSL/LVDS driver. Because the MEMS resonator is the frequency reference, no external crystal, load capacitors, or load-capacitor calculation are required, which accelerates board bring-up and removes a known source of oscillator start-up failure. Typical applications include PCIe Gen1/2/3/4 endpoint and root complex reference clocks on server motherboards, NVMe SSD controllers, network switches and routers, FPGA-based PCIe add-in cards, and industrial embedded platforms that need a robust, lead-free, RoHS-compliant 100 MHz PCIe reference without an external crystal. When designing with this part, place the device close to the PCIe PHY clock input pins, follow PCIe CEM routing guidelines (100 Ω differential, 90 Ω common-mode where required), and decouple VDD with a 0.1 µF ceramic capacitor placed within 2 mm of the supply pin. Note that this part is a generator, not a buffer, so downstream devices share the single 100 MHz output. This page synthesizes verified distributor pricing, drop-in Microchip alternatives, and practical PCB layout notes that are not duplicated in the manufacturer datasheet, giving procurement and hardware engineers a single consolidated decision point.

RFQ پەیوەندی
HCF4046M013TR - Micropower PLL, 1.4MHz, SOIC-16 | STMicroelectronics
HCF4046M013TR

HCF4046M013TR - Micropower PLL, 1.4MHz, SOIC-16 | STMicroelectronics

The STMicroelectronics HCF4046M013TR is a Micropower Phase-Locked Loop (PLL) IC operating at up to 1.4 MHz, housed in a 16-pin SOIC (0.154", 3.90mm width) package. It features quiescent current specified to 20V, very low power consumption of 70 µW (typ.) at VCO = 5V, and operating frequency range to 1.4 MHz (typ.) at VDD = 10V. The device also includes low frequency drift of 0.04%/°C (typ.) at VDD = 10V and a choice of two phase comparators: an exclusive-OR (XOR) detector and an edge-triggered sequential phase detector with charge pump output. A Phase-Locked Loop (PLL) is a closed-loop feedback system that generates an output signal whose phase is locked to the phase of an input reference signal. PLLs are widely used for frequency synthesis, modulation/demodulation, clock recovery, and tone decoding in analog and mixed-signal systems. As a member of the CMOS 4000-series logic family, the HCF4046 sits within the broader hierarchy of clock and timing integrated circuits (ICs), which also include phase-locked loops, frequency synthesizers, and clock generators. The 4046 architecture in particular is the industry-standard micropower PLL, with variants offered by multiple manufacturers. Key features of the HCF4046M013TR include a wide supply voltage range of 3V to 20V, very low quiescent current well-suited for battery-powered designs, two selectable phase comparators (Phase Comparator I for low-noise locking without dead zone, Phase Comparator II for high-noise rejection with a charge-pump output capable of driving low-pass filters), an on-chip linear VCO with external R/C tuning, and source-follower output buffer. The combination of low power, wide supply range, and dual phase comparators makes the device uniquely flexible among monolithic PLL ICs. The HCF4046 employs a CMOS architecture with an internal VCO whose gain is set by external resistor R1 and capacitor C1, and whose frequency offset is set by external R2 and C2. Phase Comparator I is an exclusive-OR gate offering low harmonic content in the locked condition but requiring 90° phase offset at the VCO input. Phase Comparator II is an edge-triggered sequential network that locks at zero phase error, allowing the loop to operate with arbitrary input duty cycles and providing a charge-pump output for direct connection to an external low-pass filter. The micropower CMOS design keeps dynamic supply current low even at maximum VCO frequency. Typical applications include FM demodulation and modulation, frequency synthesis, tone decoding, FSK (Frequency-Shift Keying) modems, motor speed control, and clock recovery from NRZ data. The wide supply range (3V to 20V) allows the device to operate directly from battery stacks, 5V logic rails, and ±15V analog supply rails with a single part number. When designing with the HCF4046M013TR, pay close attention to the loop-filter component selection, as it directly determines loop bandwidth, capture range, and lock time. Phase Comparator I requires 50% duty cycle signals for proper operation, whereas Phase Comparator II can handle any duty cycle. Bypass VDD with a 0.1 µF ceramic capacitor placed close to the IC pins to ensure clean supply rails. This page consolidates distributor pricing, verified pin-compatible drop-in alternatives, and practical loop-filter design guidance drawn from multiple sources rather than from the manufacturer datasheet alone.

RFQ پەیوەندی
HMC704LP4E - 8 GHz 19-Bit Fractional-N PLL | Analog Devices
HMC704LP4E

HMC704LP4E - 8 GHz 19-Bit Fractional-N PLL | Analog Devices

The Analog Devices HMC704LP4E is an 8 GHz, 19-bit fractional-N phase-locked loop frequency synthesizer with one output, supplied in a 24-pin VFQFN exposed-pad package. It uses a silicon-germanium BiCMOS process and combines a low-noise digital phase detector, VCO, divider, reference divider, and precision controlled charge pump. According to the manufacturer product page, the HMC704 family is designed for very low phase noise and spurious content. The manufacturer datasheet states that reference spurious levels can typically be below -100 dBc when used with a well-designed board layout. A fractional-N PLL is a frequency synthesizer that uses a controllable divider ratio to synthesize a precise output frequency from a stable reference. In the signal-chain hierarchy, this PLL belongs to clock generation and timing, then to frequency synthesis, and finally to the broader semiconductor and RF signal-control categories. Its programmable synthesis capability is useful when a system needs a local clock, modulation capability, or flexible frequency relationship between a reference source and downstream circuitry. The HMC704LP4E combines an 8 GHz synthesizer identity with a 19-bit fractional-N control word. The verified distributor listing identifies it as an integer-N/fractional-N clock-generation IC with a 24-VFQFN exposed-pad package. Its ultra-low-spurious design target makes it relevant to RF, communications, test-and-measurement, and other systems where phase noise, reference spurs, or frequency flexibility affect signal integrity. The exact reference frequency, output-frequency range, divider limits, supply currents, temperature range, and package dimensions are not included in the supplied verified text and require confirmation from the complete manufacturer datasheet. The silicon-germanium BiCMOS implementation supports the device’s combined high-frequency and low-noise synthesizer architecture. The integrated phase detector, charge pump, VCO, and divider functions reduce the number of external frequency-generation blocks while preserving programmable loop behavior. External loop-filter components and a stable reference supply remain essential design considerations because they determine loop bandwidth, phase noise, reference-spur performance, and settling behavior. Typical applications include RF transceiver clock generation, communication equipment, frequency-conversion systems, instrumentation, and test equipment. In an RF system, the synthesizer can generate a relationship between the local reference and a required channel or conversion frequency. In instrumentation, programmable frequency generation provides flexibility when the exact output frequency is selected by the host or test sequence. The most important layout consideration is preserving the low-spurious performance claimed by the manufacturer. Keep the reference and sensitive synthesizer paths short, use a stable low-noise supply, provide suitable decoupling, and follow the manufacturer’s recommended reference and loop-filter implementation. The HMC860LP3E is identified in the verified datasheet snippet as a recommended low-noise, high-PSRR regulator for minimizing external spurious sources. This page combines the verified HMC704 identity, package, synthesizer description, lifecycle indication, reference-spurious claim, and source links with clearly marked engineering data gaps. It also distinguishes verified facts from parameters that must be checked in the full datasheet before a new PCB or production design is released.

RFQ پەیوەندی
ICS1523M - 250MHz Video Clock Synthesizer | Renesas | SOIC-24
ICS1523M

ICS1523M - 250MHz Video Clock Synthesizer | Renesas | SOIC-24

Renesas Electronics ICS1523M is a 250 MHz clock synthesizer and frequency generator designed for general-purpose phase-controlled clock synthesis, line-locked and genlocked high-resolution video systems, and video projection equipment. The device is supplied in a 24-pin SOIC package measuring 0.295 inch, or 7.50 mm, in width. Its architecture uses advanced low-voltage CMOS mixed-mode technology to combine programmable frequency generation with phase-controlled operation. A clock synthesizer, also called a clock generator or phase-locked-loop-based timing device, produces one or more timing signals whose frequency and phase are controlled relative to an external reference. In a phase-locked system, the internal output remains synchronized to the reference while the feedback network determines the desired relationship. This category belongs to the Clock & Timing hierarchy, which includes clock generators, frequency synthesizers, phase-locked loops, clock buffers, and timing controllers used to coordinate digital and video systems. The principal documented feature of the ICS1523M is its 250 MHz operating frequency. Its phase-controlled frequency-generation capability makes it suitable where a system requires adjustable or externally synchronized clocks rather than a fixed-frequency oscillator. The manufacturer describes the ICS1523 family as a low-cost, high-performance solution for general-purpose clock synthesis, line-locked and genlocked high-resolution video applications, and projectors. The mixed-signal nature of the design is important in video timing systems. A reference signal establishes the synchronization point, while phase control permits the generated clock to be adjusted relative to that reference. This supports timing alignment across multiple video-processing stages and reduces reliance on multiple independent free-running clocks. Exact voltage, current, jitter, temperature, and programming-interface details were not included in the supplied source data and must be confirmed in the manufacturer datasheet before design release. ICS1523M applications include professional video timing systems, video projectors, line-locked display equipment, genlocked production systems, and general-purpose phase-controlled clock modules. In these systems, the ICS1523M can provide a coordinated timing reference for converters, processors, memory interfaces, or other circuitry requiring a stable phase-related clock. A key implementation consideration is to preserve the manufacturer's recommended reference, feedback, decoupling, and output-routing topology. Incorrect feedback connections or an unsuitable reference source can prevent phase lock or impair jitter performance. Because the verified source material does not expose complete pin assignments or electrical tables, engineers should use the official datasheet for pin connectivity, loop-filter selection, operating limits, and layout requirements. This product summary combines the verified 250 MHz, 24-SOIC package, application positioning, pricing availability, and replacement analysis with practical design guidance. It also distinguishes documented facts from parameters that still require datasheet confirmation, helping engineers evaluate the ICS1523M without treating unspecified values as guaranteed specifications.

RFQ پەیوەندی
ICS1523MT - 250MHz Video Clock Synthesizer | Renesas
ICS1523MT

ICS1523MT - 250MHz Video Clock Synthesizer | Renesas

The Renesas ICS1523MT is a video clock synthesizer with I2C programmable delay, designed for general-purpose phase-controlled clock synthesis and line-locked or genlocked high-resolution video applications. It operates as a clock-generation and timing IC with a nominal 250 MHz capability and is packaged in a 24-SOIC package. The device is listed by Renesas as a clock synthesizer within the clock-generator and PLL product family. A video clock synthesizer is a timing IC that generates, divides, delays, or phases a reference clock so downstream video-processing circuits operate from a controlled timing source. In the broader semiconductor hierarchy, the ICS1523MT belongs to the clock and timing IC category and supports power-management, display, broadcast, and video-conversion systems where predictable phase relationships and programmable timing are required. The main feature of the ICS1523MT is its I2C-programmable delay. This allows a system controller to adjust timing behavior over a serial interface rather than relying on fixed external delay components. The part is specifically suited to phase-controlled clock synthesis, where the relationship between a generated clock and an external reference must be managed precisely. Its video-clock orientation makes it useful in professional video, broadcast, monitoring, and genlocking equipment. The ICS1523MT is identified as a 24-SOIC device with a 0.295 inch, or 7.50 mm, width. The suffix MT distinguishes this ordering code from other package or temperature-related variants of the ICS1523 family. Because clock timing performance depends on reference-clock quality, board layout, output loading, and supply stability, designers should preserve short clock paths and provide the decoupling recommended by the manufacturer datasheet. Typical applications include high-resolution video timing, line-locked systems, genlocked broadcast equipment, video capture and conversion systems, and multi-standard video infrastructure. The I2C control interface is especially useful in systems where timing calibration must be adjusted dynamically during setup or when different video formats require different phase relationships. Designers should verify the complete electrical limits, register map, clock-input requirements, output characteristics, and recommended application circuit against the Renesas datasheet before layout release. The principal trade-off is that programmable delay adds control complexity, but it can reduce discrete timing hardware and improve system calibration flexibility. This page combines the verified ICS1523MT product identity, package information, clock-synthesizer classification, datasheet links, application guidance, and drop-in alternatives for engineers evaluating a PCB-compatible replacement.

RFQ پەیوەندی
ICS1524AM - Dual Output Phase Controlled SSTL_3/PECL Clock Generator | Renesas
ICS1524AM

ICS1524AM - Dual Output Phase Controlled SSTL_3/PECL Clock Generator | Renesas

The Renesas (formerly Integrated Device Technology / IDT) ICS1524AM is a dual-output phase-controlled SSTL_3/PECL clock generator integrated into a 24-pin SOIC surface-mount package. It is cataloged under clock generators, PLLs and frequency synthesizers and is described as a low-cost, very high-performance frequency generator and phase-controlled clock synthesizer, delivering two independently phase-controlled differential clock outputs from a common reference source. A clock generator is a timing IC that converts a reference frequency into one or more output clocks, forming the entry point of the clock and timing hierarchy that runs from crystal oscillator through clock generator and PLL to clock buffer and jitter cleaner. Where a plain buffer only reproduces an existing waveform, a phase-controlled clock generator adds programmable delay and frequency synthesis, allowing a board to create two related but independently adjustable clocks without a separate PLL, delay line or FPGA fabric. Key characteristics of this device include a dual-output architecture, SSTL_3/PECL-compatible differential output signalling designed for high-speed backplane and telecommunications links, phase control of each output, and a 24-SOIC package with a 0.295 inch (7.50 mm) body width. Because it is a differential ECL-family output device, it is normally used with terminated 50 ohm transmission lines, short stub lengths and controlled reference planes in multilayer boards. Internally, the device combines a phase-locked loop with programmable phase shift elements feeding two output buffers. The phase adjustment range, operating frequency band and lock characteristics are the parameters that determine whether it can lock to the system reference and deliver the required skew margin. Because it is a bipolar ECL-family design, supply rails are positive-referenced, typically around 5 V with PECL-compatible output levels, and the unused supply pins must still be connected to keep the device within its rated operating condition. Typical uses include telecommunications line-card and network interface clock distribution, server and storage backplane clock synthesis, data-converter sampling clock generation, and instrumentation or test systems that require two phase-offset clocks from a single reference. In these systems the two outputs are commonly used to create a sampling clock and a data-strobe clock, or to feed a PLL capture circuit with an offset reference clock. When laying out a board around the ICS1524AM, keep output and input traces short, provide solid ground-plane continuity under the device, and place termination close to the receiver. Verify differential pair length matching, keep the phase-control network away from high-speed output routing, and confirm the reference clock amplitude meets the input sensitivity requirement in the manufacturer datasheet before committing the layout. This page consolidates device classification, package details, drop-in ordering variants, and practical layout guidance into one engineering reference, so you can evaluate the ICS1524AM against alternative dual-output clock generators without hunting through separate distributor listings and application notes.

RFQ پەیوەندی
ICS1526G - 110MHz Clock Synthesizer, 16-TSSOP | Renesas
ICS1526G

ICS1526G - 110MHz Clock Synthesizer, 16-TSSOP | Renesas

The Renesas Electronics ICS1526G is a low-cost, high-performance clock/frequency synthesizer IC with a maximum operating frequency of 110 MHz, packaged in a 16-pin TSSOP (0.173 inch, 4.40 mm width). It is built on IDT's advanced low-voltage CMOS mixed-mode technology and is positioned as a general-purpose phase-controlled clock synthesis solution as well as a line-locked and genlocked high-resolution video timing generator. A clock synthesizer (also called a PLL-based frequency generator or clock generator IC) is a timing IC that multiplies, divides, or regenerates a reference clock into one or more stable output frequencies. It belongs to the clock and timing hierarchy inside integrated circuits, sitting between a crystal oscillator and the logic, memory, or display circuitry that consumes the clock. Unlike a simple crystal oscillator, a PLL-based synthesizer can derive many related output frequencies from one low-frequency reference and can phase-align those outputs to an external video sync source. Key characteristics of the ICS1526G include a 110 MHz maximum frequency, a single clock/frequency synthesizer function, and 16-TSSOP surface-mount packaging. The device is specifically suited to video projectors and displays across multiple resolutions, where the master oscillator frequency and lock behavior determine whether the generated timing is stable enough for pixel-perfect image reproduction. Technically, the ICS1526 relies on a phase-locked loop to lock an internal VCO to a reference input, then divides or multiplies that locked frequency down to the desired output. The mixed-mode CMOS implementation combines analog loop control with digital frequency programming, which is why phase adjust and lock detection features are central to its use in genlocked video systems. Typical applications include video projector timing generation, professional video monitoring equipment, broadcast and studio reference distribution, genlocked display systems, industrial imaging panels, and general-purpose clock trees for consumer and industrial electronics where a single reference source must fan out to multiple derived clocks. When designing with the ICS1526G, verify the reference frequency window, the required output divider ratios, and loop lock acquisition time for your target video standard. Also confirm that your output jitter and skew budget is satisfied before committing to the part, since these parameters are not published in the distributor listings summarized on this page. This page consolidates distributor availability, package details, drop-in alternatives from the same Renesas/IDT clock-generator family, and practical design guidance that is not consolidated in any single distributor product page.

RFQ پەیوەندی
ICS1526GT - 110MHz Clock Synthesizer | Renesas | Video
ICS1526GT

ICS1526GT - 110MHz Clock Synthesizer | Renesas | Video

Renesas Electronics ICS1526GT is a 110 MHz clock and frequency synthesizer IC with one clock output in a 16-pin TSSOP package measuring 4.40 mm wide. It is designed for general-purpose phase-controlled clock synthesis and for line-locked or genlocked high-resolution video systems. A clock synthesizer is an integrated timing circuit that generates or organizes clock signals for another circuit. Within the broader semiconductor hierarchy, the ICS1526GT belongs to the clock and timing IC family, where it sits between a basic oscillator and a more complex PLL-based clock-generation solution. Its frequency-generation architecture allows a system to derive synchronized timing for video projection, display, and other phase-sensitive equipment. The principal rated operating frequency is 110 MHz, and the device provides one clock output in a 16-TSSOP package. The 4.40 mm package width supports compact, surface-mount PCB construction without using a large through-hole footprint. Its low-voltage CMOS mixed-mode process technology combines digital timing functions with analog phase-control behavior, which is useful when multiple system clocks must remain aligned. The ICS1526GT is particularly suited to general-purpose phase-controlled clock synthesis. In a video projector or display, timing relationships determine pixel synchronization and image stability. Line-locked and genlocked operation allows the generated clock to remain referenced to an external video signal, helping downstream circuits reproduce stable horizontal and vertical timing. The 110 MHz operating point also provides a useful reference point for timing designs requiring precise phase alignment. Typical uses include video projectors, professional displays, broadcast-compatible video equipment, line-locked timing modules, genlock distribution systems, and clock-generation boards. The same synthesizer can also serve as the timing reference in an industrial imaging system when its operating conditions, lock behavior, and electrical limits match the intended source and output architecture. When designing around the ICS1526GT, preserve the manufacturer’s recommended input, output, and decoupling arrangements. Signal-integrity performance depends on keeping the clock route compact, providing a stable reference source, and observing the allowable loading and timing ranges. Because phase-control and synchronization behavior are central to this device, evaluate the complete external loop rather than judging suitability from the 110 MHz headline frequency alone. This product page combines the manufacturer’s clock-generation description with the 110 MHz frequency, single-output configuration, 16-TSSOP package information, practical application guidance, and verified source links. It also identifies the sourcing and engineering questions that should be resolved before the device is placed into a new line-locked, genlocked, or phase-controlled timing design.

RFQ پەیوەندی
ICS1574BM - Programmable Laser Clock Generator | Renesas
ICS1574BM

ICS1574BM - Programmable Laser Clock Generator | Renesas

Renesas Electronics ICS1574BM is a user-programmable laser engine pixel clock generator built around a monolithic phase-locked-loop frequency synthesizer. It generates the timing signals required by laser-engine imaging systems and is specified in a 16-pin SOIC package. The device description identifies advanced CMOS mixed-mode PLL technology, combining programmable frequency synthesis with clock-generation functionality in one integrated circuit. A phase-locked loop, or PLL, is a feedback-controlled frequency synthesizer that locks an internally generated output to a reference clock. By phase-locking the output to a stable reference, the ICS1574BM provides a controlled relationship between its program settings and the resulting laser-engine pixel timing. This makes it part of the broader clock and timing IC hierarchy: pixel clock generator, PLL frequency synthesizer, clock-generation IC, timing IC, and semiconductor. The principal feature of the ICS1574BM is user programmability. Programming lets a laser-imaging system tune pixel-clock behavior for different operating conditions instead of relying on a fixed-frequency output. The monolithic construction reduces the number of separate frequency-synthesis components, while the CMOS mixed-mode architecture combines analog phase detection with digital control functions. The 16-SOIC package also provides a compact surface-mount option for laser-engine electronics. The ICS1574BM is specifically positioned for laser-engine applications, where pixel timing must remain synchronized with scanning, modulation, and image-processing systems. Its frequency-synthesizer architecture makes it relevant where adjustable clock generation and deterministic reference locking are required. Because exact operating limits and programming electrical characteristics are defined by the manufacturer datasheet, system designs should verify output-frequency range, reference-input requirements, jitter, supply voltage, and acquisition time against the intended optical configuration. Typical deployments include laser projection engines, scanning-laser systems, optical inspection equipment, and image-generation assemblies. In each case, the clock generator provides the programmable timing foundation needed to coordinate pixel generation with downstream drivers and controllers. The integration of PLL synthesis and pixel-clock generation is particularly useful when component count, board area, and synchronization control are important design constraints. A robust implementation should route the reference clock cleanly, keep programming-interface traces away from sensitive feedback paths, and follow the recommended bypass-capacitor and grounding layout in the manufacturer datasheet. Designers should also validate startup, lock behavior, and output jitter across the complete temperature range of the assembled laser engine rather than evaluating only nominal bench conditions. This product page combines the device identity, package information, application engineering guidance, datasheet links, and cross-reference findings into a design-focused reference. It also distinguishes the verified operating concept of the ICS1574BM from specifications that must be confirmed directly in the manufacturer datasheet before schematic release or production qualification.

RFQ پەیوەندی
ICS180M-01 - Low EMI Clock Generator | Renesas Electronics
ICS180M-01

ICS180M-01 - Low EMI Clock Generator | Renesas Electronics

The Renesas Electronics ICS180M-01 is a low-EMI, single-output spread-spectrum clock generator with a maximum output frequency of 28 MHz in an 8-pin SOIC package. It accepts either a clock or crystal input, produces a CMOS output, and provides a 1:1 input-to-output ratio. The device uses a proprietary combination of analog and digital phase-locked-loop technology to generate a low-EMI output clock. A spread-spectrum clock generator is a clock and timing IC that varies clock energy over a controlled frequency band. This technique reduces narrowband electromagnetic emissions by distributing clock energy across multiple frequencies rather than concentrating it around one carrier. In the broader semiconductor hierarchy, the ICS180M-01 belongs to clock and timing ICs, PLL-based clock synthesis, and broader frequency-generation and timing-control devices. The ICS180M-01 supports both clock and crystal input, giving a designer flexibility when the board already contains a reference oscillator or requires operation from a crystal. Its single CMOS output is suitable for systems that need one low-EMI clock domain. The 28 MHz maximum output frequency covers applications requiring moderate-speed digital clock distribution, although the minimum operating frequency and detailed timing limits are not stated in the available product records. The central architectural feature is the proprietary mix of analog and digital PLL technology. A PLL locks the generated output to the selected reference, while spread-spectrum modulation controls the clock spectrum and reduces electromagnetic interference concentration. The device contains one clock-generation circuit, and its stated 1:1 input-to-output ratio indicates that the output frequency follows the input reference without a stated frequency multiplication or division ratio. Typical uses include EMI-sensitive digital control systems, communications equipment, industrial electronics, and clock-distribution subsystems in which reducing narrowband clock radiation is important. The device can also serve as a low-EMI reference-clock source in equipment with multiple digital subsystems, provided the reference frequency and all timing requirements remain within the device's operating limits. PCB implementation should preserve a short, controlled return path from the input reference and provide a clean supply connection to the clock generator. Decoupling should follow the manufacturer application guidance, and unused input or output states should be handled according to the datasheet rather than inferred from the brief device description. Differential clock-impedance requirements should be checked before using the CMOS output in a high-speed or length-sensitive topology. This product record combines the device's key functional characteristics, sourcing information, and design-oriented comparison points. It also distinguishes the confirmed 180M-01LF drop-in candidate from unverified similarly named clock ICs, helping engineers identify replacements without confusing functional similarity with guaranteed pin compatibility.

RFQ پەیوەندی
ICS180M-03 - 28MHz Low EMI Clock Generator | Renesas
ICS180M-03

ICS180M-03 - 28MHz Low EMI Clock Generator | Renesas

Renesas ICS180M-03 is a low-EMI spread-spectrum clock generator that accepts a clock or crystal input and produces a CMOS output clock with a maximum frequency of 28 MHz. The device uses mixed analog and digital phase-locked-loop technology to reduce electromagnetic interference. It is packaged in an 8-pin SOIC measuring 0.154 inch, or 3.90 mm, in width and operates from 3.135 V to 5.5 V. A spread-spectrum clock generator is a clock and timing IC that deliberately varies clock frequency over a defined range. This frequency spreading distributes spectral energy across multiple bins, reducing the peak conducted and radiated emissions produced by a narrowband digital clock. The ICS180M-03 belongs to the clock generator, PLL, and frequency-synthesizer hierarchy within clock and timing semiconductor products. The principal features of the ICS180M-03 include one clock-generating circuit, support for either clock or crystal inputs, CMOS output logic, and a 1:1 input-to-output frequency ratio. Its maximum operating output frequency is 28 MHz. These characteristics make it suitable for systems that require a low-EMI reference clock while retaining a conventional, single-output clock architecture. Internally, the device combines analog and digital phase-locked-loop functions. The PLL locks the generated output to the external clock or crystal reference, while spread-spectrum operation broadens the output spectrum and lowers its peak frequency concentration. The manufacturer datasheet describes this combination as a method for producing a low-EMI output clock while preserving accurate frequency generation. Typical applications include EMI-sensitive digital equipment, interface and communication modules, embedded control systems, and general-purpose clock-distribution designs. In each case, the part can provide the system timing reference while limiting narrowband emissions from the associated clock line. The 8-SOIC surface-mount package also supports standard automated PCB assembly and compact board-space utilization. When designing around the ICS180M-03, preserve the recommended input, output, and decoupling connections described in the manufacturer datasheet. Pay particular attention to crystal or clock-source stability because a phase-locked-loop generator derives its output from that reference. Confirm the intended supply voltage, output loading, trace topology, and EMI target before releasing the PCB layout. This product page combines the device specifications, sourcing guidance, application context, and practical design considerations engineers need when evaluating the ICS180M-03 for a low-EMI clock-generation design.

RFQ پەیوەندی
ICS180M-51 - 28MHz Low EMI Clock Generator | Renesas
ICS180M-51

ICS180M-51 - 28MHz Low EMI Clock Generator | Renesas

The Renesas Electronics ICS180M-51 is a low-EMI single-output spread-spectrum clock generator that operates from a clock or crystal input. It combines IDT proprietary analog and digital phase-locked-loop technology, supports a maximum frequency of 28 MHz, and provides a CMOS output with a 1:1 input-to-output ratio. The device is offered in an 8-pin SOIC package. A clock generator is an integrated circuit that produces a stable timing reference for digital systems. It may accept an existing reference clock or a crystal and use a phase-locked loop, or PLL, to create a related output frequency. Clock generators are used to support processor timing, data conversion, communications, storage, and other digital subsystems. The ICS180M-51 belongs to the clock generator and timing-IC hierarchy rather than the general-purpose logic IC category. The central feature of the ICS180M-51 is its low-EMI output. According to the ICS180-51 datasheet, the device offers center-spread selections of ±0.625% and ±1.875%. These selections allow a clock's spectral energy to be distributed across a wider frequency range, which can reduce the peak magnitude of narrowband emissions when used as an EMI mitigation technique. The single output stage uses CMOS signaling and has a listed 1:1 input-to-output ratio. The ICS180-51 combines analog and digital PLL functions to derive its output from a clock or crystal input. This architecture allows a single device to operate as a low-EMI clock generator rather than requiring a separate fixed-frequency oscillator arrangement. The Renesas datasheet also identifies related MK1714-01 and MK1714-02 devices as references for a wider selection of input frequencies and multipliers when a design requires more flexible frequency translation than the ICS180-51 provides. Typical uses include EMI-sensitive digital equipment, communications equipment, and systems requiring a low-EMI clock derived from an existing reference. The device is also suitable where spread-spectrum clocking is used to reduce discrete spectral components. It can serve as a timing reference for processors, interface circuits, converters, and other clocked digital logic where a CMOS output at up to 28 MHz is required. When designing around the ICS180M-51, first confirm that the source frequency, selected spread mode, and required output frequency are supported by the device configuration. Place the clock input and output traces for controlled impedance and maintain short return paths to the device ground pins. Verify conducted and radiated emissions at the finished-product level because spread-spectrum timing alone does not establish regulatory compliance. This page consolidates the device type, operating limits, spread-spectrum selections, package information, sourcing guidance, and design cautions into one engineering reference. It also provides practical application analysis, alternative-part qualification guidance, and a structured comparison framework for evaluating the ICS180M-51 against other low-EMI clock-generator options.

RFQ پەیوەندی
ICS2402M - Multiplier Zero Delay Buffer | Renesas
ICS2402M

ICS2402M - Multiplier Zero Delay Buffer | Renesas

The Renesas ICS2402M is a multiplier and zero-delay buffer integrated circuit with one single-ended LVCMOS output, supplied in an 8-pin SOIC package. The device uses ICS proprietary analog/digital phase-locked-loop techniques to multiply an input clock and reproduce a buffered clock output with low propagation delay. Its clock-buffer function makes it suitable for clock distribution, frequency conversion, communications, industrial control, and other systems requiring a multiplied or redistributed clock signal. A zero-delay buffer, or ZDB, is a clock and timing semiconductor that combines frequency multiplication or conditioning with buffered clock propagation. In the broader product hierarchy, ICS2402M belongs to clock and timing ICs and ultimately to the semiconductor category. Unlike a passive resistor-and-capacitor delay line, an active ZDB uses PLL techniques to establish the output relationship and provide a low-delay clock output. The verified product information identifies the ICS2402M as a multiplier and zero-delay buffer, with one LVCMOS output and a single-ended signal arrangement. The 8-SOIC package supports conventional surface-mount PCB assembly. Verified distributor information also identifies the component as lead-free and RoHS compliant. Exact operating limits, supply-voltage range, supported multiplication ratios, frequency range, output impedance, and timing tolerances were not present in the supplied source excerpts and therefore require confirmation from the manufacturer datasheet before design release. Technically, the ICS2402M integrates analog and digital PLL methods to multiply a reference clock while buffering the result. This architecture is intended to reduce the timing penalty normally encountered when a system must distribute a clock derived from a lower-frequency reference. The single-ended LVCMOS interface can simplify connection to conventional digital logic, but signal-integrity review remains necessary because PLL multipliers can amplify supply noise and produce clock-related harmonics. Typical uses include processor and communications clock generation, frequency-interface bridging, industrial data-acquisition systems, and retrofit designs requiring a clock output derived from an existing reference. In each case, the designer must confirm that the selected multiplier ratio, input frequency, output frequency, and supply voltage fall within the limits documented for the exact ICS2402M ordering configuration. For implementation, begin by reviewing the pin assignment and recommended decoupling in the manufacturer datasheet, then validate the output waveform with the intended clock load. Keep the clock trace short where possible, provide a clean return path, and account for PLL lock and startup behavior in the system timing budget. Because the verified excerpts do not provide the complete timing table, board release should be conditional on checking the official electrical characteristics and reference circuit. This product record combines verified device identity, package, interface, regulatory, and sourcing information with application-specific design guidance. It also separates confirmed facts from parameters that remain unavailable, helping engineers distinguish source-backed characteristics from values that still require datasheet confirmation.

RFQ پەیوەندی
ICS252PM - 200MHz Dual-Output Clock Synthesizer | Renesas
ICS252PM

ICS252PM - 200MHz Dual-Output Clock Synthesizer | Renesas

The Renesas Electronics ICS252PM is a field-programmable dual-output spread-spectrum VersaClock synthesizer with an operating output-frequency range up to 200 MHz in an 8-SOIC package. The device generates two independently programmable output frequencies and is intended for clock and frequency-distribution systems requiring programmable frequency generation with spread-spectrum clocking. A clock synthesizer is a clock-and-timing integrated circuit that generates or distributes one or more related clock signals. In the broader hierarchy, ICS252PM belongs to the clock generator and frequency synthesizer family, within clock and timing ICs and ultimately the semiconductor category. Its dual-output architecture can reduce the number of separate oscillator and distribution components required in a system. The verified product information identifies ICS252PM as a low-cost, field-programmable, dual-output clock synthesizer capable of generating two output frequencies from 314 kHz to 200 MHz. The 200 MHz upper limit makes the device applicable to communication equipment, storage systems, computer peripherals, and other systems requiring a programmable clock. Spread-spectrum operation can reduce peak spectral concentration, although exact modulation settings and implementation limits must be confirmed in the manufacturer datasheet. The ICS252PM uses independently programmable output stages rather than a fixed-frequency oscillator arrangement. This allows one device to serve multiple clock domains when two related but unequal frequencies are required. Because it is a digital-programmable clocking component, board design should account for trace propagation, output loading, supply integrity, and EMI behavior associated with high-frequency clock distribution. The part is offered in an 8-SOIC package, providing a conventional surface-mount footprint for PCB assembly. In an 8-SOIC, the exact pin names, programming interface, supply voltage, output-drive capability, operating-temperature range, and electrical limits are not supplied in the verified excerpts and are therefore identified as data needed rather than estimated. Typical uses include clock generation for networking and communication equipment, read/write timing in storage systems, industrial control electronics, and embedded computing platforms. Validate the required frequency range, jitter, skew, supply voltage, and output configuration against the complete manufacturer datasheet before releasing a production design. This product record combines verified distributor identification, package and frequency information, sourcing links, application guidance, and practical selection criteria. It distinguishes explicitly verified facts from parameters that still require confirmation, helping engineers avoid unsupported assumptions while locating an ICS252PM replacement or equivalent.

RFQ پەیوەندی
ICS270PG - 200MHz Triple-PLL VCXO Clock Synthesizer | Renesas
ICS270PG

ICS270PG - 200MHz Triple-PLL VCXO Clock Synthesizer | Renesas

Renesas Electronics Corporation ICS270PG is a field-programmable voltage-controlled crystal oscillator and triple-PLL clock synthesizer that generates up to eight high-quality, high-frequency clock outputs. It supports a maximum frequency of 200 MHz, uses a crystal input, provides CMOS outputs, includes PLL bypass, and is packaged in a 20-pin TSSOP measuring 0.173 inch, or 4.40 mm, wide. A clock synthesizer is an integrated timing device that accepts a reference source and derives one or more stable, programmable clock outputs for digital systems. A VCXO adds voltage-controlled frequency adjustment to the crystal reference, while a PLL multiplies or divides that reference to produce the required output frequencies. The ICS270PG combines both functions in a clock and timing IC, allowing one reference crystal to serve multiple clock domains. Its principal features include three phase-locked loops, PLL bypass capability, one internal clock circuit, a crystal reference input, and CMOS output signaling. The synthesizer can generate as many as eight outputs, including multiple reference clocks originating from a low-frequency reference source. This output flexibility reduces the number of separate oscillators required in systems requiring related but unequal clock rates. The triple-PLL architecture separates clock-generation functions that might otherwise require multiple oscillator and divider combinations. PLL bypass is useful during configuration, test, or operating conditions where a directly derived clock path is preferred. CMOS outputs are suitable for interfacing with modern digital logic, while the 200 MHz maximum output frequency supports demanding processor, communications, data-conversion, and industrial control clock trees. Typical applications include communications infrastructure, instrumentation, industrial automation, test and measurement equipment, data-acquisition systems, and embedded control platforms. In each case, the device can centralize multiple clock requirements around a crystal reference and provide programmable outputs instead of requiring a separate oscillator for each frequency domain. The multiple reference outputs can support communication links, data converters, memory interfaces, and digital control logic within one clock tree. The principal design consideration is the device's programmed configuration and the resulting relationships among its three PLLs, reference outputs, and output dividers. Review the manufacturer datasheet's pin-description table, recommended external components, clock-output constraints, and programming procedure before laying out a new board. PCB placement should minimize clock traces and keep the crystal and associated components close to the device. This product page summarizes the documented architecture, package information, output capability, and practical design considerations of the ICS270PG. It also distinguishes verified technical facts from details that still require confirmation from the manufacturer datasheet, helping engineers plan the architecture without overlooking programming, layout, or qualification work.

RFQ پەیوەندی
ICS271PG - Triple PLL VCXO Clock Synthesizer | Renesas
ICS271PG

ICS271PG - Triple PLL VCXO Clock Synthesizer | Renesas

The Renesas Electronics ICS271PG is a triple-PLL, field-programmable VCXO clock synthesizer that generates up to six high-quality clock outputs and operates up to 200 MHz in a 20-pin TSSOP package. It accepts a crystal input, provides CMOS outputs, supports PLL bypass, and combines one clock-synthesis circuit with multiple reference and high-frequency outputs. These characteristics make it suitable for systems that require flexible clock generation from a low-frequency crystal source. A VCXO, or voltage-controlled crystal oscillator, is a clock-generation technique in which an oscillator’s frequency can be controlled by an external voltage. A field-programmable VCXO clock synthesizer extends that concept by combining crystal-referenced timing with programmable phase-locked loops and selectable output divisions. Within the broader hierarchy, the ICS271PG belongs to the clock and timing IC category, specifically the PLL and frequency-synthesizer class, and can replace multiple discrete crystal and oscillator arrangements when system designers need several related frequencies from one reference. Key features include three PLL capability, up to six generated clock outputs, a maximum frequency of 200 MHz, CMOS output logic, crystal input, and PLL bypass operation. The six-output architecture supports systems that need both reference clocks and higher-frequency working clocks. Field programming allows the device to be configured for different output requirements, while PLL bypass provides a path for systems that need to select between synthesized and direct-reference operating conditions during design or validation. Technically, the ICS271PG uses a crystal-referenced architecture with programmable PLL and output stages. The low-frequency crystal source establishes a stable reference from which the internal synthesis circuitry can derive multiple clock outputs. CMOS output signaling supports integration with digital logic operating in the same clock domain. Because the device is controlled through VersaClock software according to its documentation, configuration should be completed with the intended output frequencies, divider relationships, and operating modes validated together rather than selected independently. Typical applications include communications equipment, interface controllers, digital signal processing systems, test and measurement instruments, and embedded systems that require several coordinated clock outputs. It can also serve clock-distribution designs where a central synthesizer offers a more scalable alternative to multiple separately sourced oscillators. In each case, the main design benefits are centralized referenceing and programmable output relationships. The primary design consideration is preserving clean, deterministic clock behavior across every enabled output. Use the manufacturer’s configuration procedure, validate each output against its assigned load, and check startup and bypass transitions with the final system timing budget. PCB layout should follow the datasheet guidance for crystal connections, supply decoupling, and output routing to minimize jitter and crosstalk. This page organizes the device’s clock-generation characteristics, drop-in candidate listings, application guidance, and engineering design considerations. It is intended to help engineers compare the ICS271PG with equivalent field-programmable clock synthesizers before committing to a board design or production sourcing plan.

RFQ پەیوەندی
ICS275PG - 200MHz Triple-PLL VCXO Clock Synthesizer | Renesas
ICS275PG

ICS275PG - 200MHz Triple-PLL VCXO Clock Synthesizer | Renesas

The Renesas Electronics ICS275PG is a triple-PLL field-programmable VCXO clock synthesizer with a maximum output frequency of 200 MHz, supplied in a 16-pin TSSOP surface-mount package. It operates from a 3.135 V to 3.465 V supply, accepts a crystal reference input, provides CMOS clock outputs, and can generate as many as four high-quality clock outputs. A VCXO, or voltage-controlled crystal oscillator, is a clock-generation architecture that combines a crystal oscillator with voltage-controlled frequency adjustment. A PLL, or phase-locked loop, locks an internal oscillator to a reference signal and provides programmable frequency synthesis. The ICS275PG therefore belongs to the clock synthesizer and frequency generator hierarchy, where it functions as a timing IC for communications, industrial control, and digital processing systems. The device's principal features include three PLL sections, PLL bypass capability, a crystal reference input, CMOS output technology, and operation up to 200 MHz. The multiple output architecture allows one reference source to feed several related clock domains. Its field-programmable nature also permits output-frequency and phase relationships to be configured for systems that require more flexibility than a fixed-frequency oscillator. The ICS275PG uses a 3.3 V-class supply range centered on the conventional 3.3 V operating point. Its specified 0°C to 70°C temperature range supports commercial-temperature equipment, although the datasheet pin description and detailed electrical limits must be checked before applying the device outside that range. The TSSOP-16 package is intended for surface-mount assembly and supports compact board layouts without requiring a through-hole package. Typical uses include generating reference and communication clocks, distributing clocks among multiple digital subsystems, and synthesizing programmable clock outputs for test and measurement equipment. It is particularly relevant where several outputs must remain phase-related to a common crystal reference. The CMOS outputs are suited to digital logic interfaces when their voltage, timing, and drive requirements are checked against the receiving circuitry. PCB implementation should preserve a short return path from each supply connection to ground, place decoupling capacitance close to the device, and route clock outputs as controlled-impedance traces when timing margin is limited. Follow the manufacturer's recommended crystal and load-capacitance configuration because oscillator startup, frequency accuracy, and loop stability depend on the complete reference network rather than the IC alone. This page organizes the ICS275PG's clock-generation capabilities, package information, application guidance, and design considerations. It also provides an explicit framework for evaluating replacement requirements, including package compatibility, pin compatibility, supply voltage, output type, and maximum operating frequency.

RFQ پەیوەندی