Clock & Timing
بەرهەمەکان (970+)
AD9834BRU - 75 MHz 10-Bit DDS IC | Analog Devices
The Analog Devices AD9834BRU is a 75 MHz low-power direct digital synthesis IC that generates sine and triangular waveforms with 10-bit output resolution and is packaged in a 20-lead TSSOP. It operates from a 2.3 V to 5.5 V supply, consumes 20 mW at 3 V, and includes an on-board comparator for producing a square-wave clock output. A direct digital synthesizer, or DDS, is a programmable waveform generator controlled by a phase accumulator and phase-to-amplitude conversion. The DDS hierarchy places this device among clock and timing integrated circuits, where it converts serial frequency-control data into a digitally synthesized output. Unlike a conventional analog signal source, its frequency can be changed through a serial interface without retuning an inductor or capacitor. The AD9834BRU supports frequency modulation and phase modulation, while its internal architecture provides sine and triangular output waveforms. Its 10-bit resolution defines the discrete amplitude steps available in the generated output. The 75 MHz headline clock capability permits high-speed phase accumulation, making the device useful for precision excitation, waveform generation, clock synthesis, and frequency-sweep test systems. The serial programming interface reduces the number of control pins required on small and mixed-signal systems. A master clock establishes the operating reference, and the frequency-control registers determine the synthesized output. The internal comparator provides a separate square-wave output path for clock-generation applications. This combination allows one programmable device to serve both as a sine or triangle source and as a digital clock output. Typical applications include function generators, automated test equipment, communications test loops, industrial sensor excitation, audio signal generation, and programmable clock products. Its low 20 mW operating-power figure at 3 V is particularly useful in portable instruments and battery-powered test equipment, where every milliwatt contributes to overall energy consumption. PCB implementation should preserve a quiet return path around the supply and ground pins, place decoupling capacitors close to the device, and route the master-clock signal away from sensitive analog and output nodes. Because the AD9834BRU is specified in a compact TSSOP package, careful solder-paste control and adequate thermal copper are important for reliable assembly and stable operation. This product page combines the manufacturer specifications with a practical comparison of verified ordering variants, interface and waveform capabilities, package details, application guidance, and design notes that help engineers evaluate the AD9834BRU for programmable waveform and clock-generation designs.
AD9835BRU - 50MHz 10-Bit DDS IC | Analog Devices
Analog Devices AD9835BRU is a 50 MHz direct digital synthesis IC with a 10-bit on-chip DAC, 32-bit frequency tuning word, and 16-lead TSSOP package. It generates digitally created sine waves up to 25 MHz and supports serial frequency and phase modulation from a reference clock. A direct digital synthesizer, or DDS, is a programmable waveform generator built around a phase accumulator, waveform lookup table, and digital-to-analog converter. The AD9835 combines these blocks on one CMOS device, allowing an external microcontroller or logic circuit to control the generated frequency through serial data writes. In system terms, it belongs to the clock and timing hierarchy, combining a digital waveform engine with an analog output stage. The AD9835BRU operates from a 5 V supply and reaches a maximum clock speed of 50 MHz. Its on-chip 10-bit DAC provides the sine-wave output, while the 32-bit tuning word allows detailed frequency control when combined with the reference clock. The device also includes a COS lookup table, phase-modulation and frequency-modulation capabilities, a power-down option, and serial loading for programming from external logic. Internally, the phase accumulator converts the programmed frequency tuning word into a phase address. The COS lookup table translates that address into a digital waveform value, and the 10-bit DAC converts the result into the analog output. This architecture permits frequency changes through serial control rather than an analog tuning element, making the output suitable for controlled, repeatable signal generation. Typical applications include DDS tuning, digital demodulation, waveform generation, communications test equipment, and frequency synthesis. The AD9835 is particularly appropriate when an adjustable or modulated sine source is needed with a compact 16-lead TSSOP footprint. Its 5 V supply and single-chip architecture also simplify circuits that would otherwise require a divider, DAC, and external waveform memory. Designers should account for output filtering, reference-clock stability, and DAC output compliance. The manufacturer states that the device can create sine waves up to 25 MHz, but the usable output spectrum depends on the reference clock, frequency-word calculation, external reconstruction filter, and output-network impedance. Power-supply decoupling and a clean clock source are particularly important for minimizing phase noise and unwanted harmonics. This page combines the manufacturer architecture description with application-oriented guidance for DDS tuning, digital demodulation, and modulated signal generation. It also organizes package, programming, sourcing, and replacement information to support faster engineering decisions and board-level planning.
AD9850BRS - 10-Bit 125 MHz DDS Synthesizer | Analog Devices
The Analog Devices AD9850BRS is a complete direct digital synthesis IC that combines a digitally programmable frequency synthesizer, a 10-bit high-speed DAC, and a comparator in a 28-lead SSOP package. It supports a maximum system clock of 125 MHz, provides 32-bit frequency tuning, and accepts serial or parallel programming of the phase and frequency control words. The AD9850BRS also includes an internal high-speed, high-performance DAC and comparator, allowing it to generate a spectrally pure analog output when referenced to an accurate clock source. A direct digital synthesizer, or DDS, is a frequency-generation architecture that uses a phase accumulator and a numerically controlled waveform lookup followed by a DAC. Unlike a conventional integer-N or fractional-N frequency synthesizer, a DDS derives its output frequency directly from a frequency tuning word. The AD9850BRS therefore belongs to the oscillator and clock-generator hierarchy and can replace combinations of divider chains, digital counters, DACs, and comparators in precision signal-source designs. The primary device characteristics include a 10-bit DAC resolution, 125 MHz maximum clock rate, and 32-bit frequency tuning word. These parameters define the device as a compact single-chip DDS solution rather than a general-purpose logic IC. Because the DAC is 10 bits, spectral performance depends strongly on output filtering and on the quality of the reference clock. The comparator output supports use as a square-wave reference, while the analog DAC output provides a sinusoid at the programmed frequency. The AD9850 generates its output from a stable reference clock and a digitally loaded frequency and phase word. Increasing the phase-word resolution supports finer frequency control, while phase adjustment permits precise placement of the generated signal relative to other clocks. The internal comparator can sharpen the analog waveform into a digital-compatible clock output, which is useful when downstream circuitry requires cleaner edges than the raw DAC waveform provides. Typical uses include variable-frequency oscillators, sine-wave generators, clock and trigger sources, amplitude or frequency-modulation experiments, local-oscillator subsystems, automatic test equipment, and embedded signal-processing fixtures. The 28-lead SSOP package is also suitable for laboratory instruments and communication equipment where a programmable clock with an adjustable phase relationship is required. When designing a board around the AD9850BRS, provide a low-jitter reference clock, route the DAC output through an appropriate reconstruction filter, and use the comparator output when a digital clock is required. The 10-bit DAC quantization produces harmonics and spurs that a low-pass filter must suppress, and reference-clock jitter translates directly into output phase noise. This page combines the manufacturer device description, distributor package and availability details, package dimensions, pricing references, and application-oriented engineering guidance. It also identifies a same-family 28-lead SSOP option and explains the interface, filtering, and layout considerations that determine whether the AD9850BRS is suitable for a given precision signal-source design.
AD9851BRS - 180 MHz 10-Bit DDS Synthesizer | Analog Devices
The Analog Devices AD9851BRS is a 180 MHz, 10-bit direct digital synthesis IC that combines a digitally programmable frequency synthesizer, internal high-speed DAC, and comparator in a 28-lead SSOP package. It uses a 32-bit tuning word for frequency control and operates from supply voltages above 3.0 V over an industrial temperature range of -40°C to +85°C. The AD9851BRS provides a compact solution for precision clock generation, frequency synthesis, waveform generation, and phase-control applications. A direct digital synthesizer, or DDS, is a frequency-generation architecture that uses a phase accumulator, phase-to-amplitude converter, and DAC to create a digitally controlled output waveform. Within the broader signal-chain hierarchy, the AD9851 integrates DDS logic and an analog output stage in one package. This integration reduces external component count and simplifies control through serial or parallel programming interfaces while preserving direct digital frequency control. The key features of the AD9851BRS include its 180 MHz internal clock capability, 10-bit DAC resolution, 32-bit frequency tuning word, integrated high-speed comparator, and 28-lead SSOP package. The 32-bit tuning word enables fine frequency increments, while the 10-bit DAC defines the quantization available on the generated analog waveform. The integrated comparator allows the output to be used as a square-wave clock or for edge-sensitive timing applications. The AD9851 architecture separates digital frequency programming from the analog output path. A phase accumulator advances by the selected tuning value, and the resulting phase is converted into an amplitude value before the DAC generates the output waveform. The internal comparator reconstructs a binary version of that waveform. This arrangement is useful when a system needs a programmable output frequency but does not require a separate high-resolution DAC or external waveform-generation circuitry. Typical uses include communication-clock synthesis, waveform generation, frequency-hopping systems, tunable oscillator replacement, test-and-measurement signal sources, and phase-control circuits. Its 28-lead SSOP format makes it particularly relevant to compact frequency-generation modules and legacy instrumentation designs. Designers should preserve the required decoupling and controlled-impedance routing around the clock, data, and analog-output connections. The principal design trade-off is that the 10-bit DAC establishes finite output amplitude quantization, while the very high internal clock supports rapid frequency changes and fine tuning resolution. External filtering is generally required to remove image content or unwanted harmonics from the DAC output. The manufacturer datasheet should be used to assign every SSOP pin and to implement the recommended power, ground, and analog-output layouts. This page combines the exact AD9851BRS ordering information with package details, practical replacement guidance, comparison data, and design-focused guidance for DDS clock-generation designs. It also distinguishes the AD9851 family from the pin-compatible AD9850 generation, helping engineers assess frequency-range, programming, and lifecycle implications before making a board-level substitution.
AD9852AST - 12-Bit 300 MSPS DDS Synthesizer | Analog Devices
The Analog Devices AD9852AST is a 12-bit, 300 MSPS complete direct digital synthesis, or DDS, synthesizer with a 48-bit tuning word and an internal high-speed DAC. The device is offered in an 80-lead LQFP package and operates from a 3.3 V supply. It combines a digital phase accumulator, frequency-to-phase converter, interpolation filtering, and a current-output DAC in one programmable synthesis engine. A DDS is a digital frequency synthesizer that generates a periodic output waveform from a phase accumulator and lookup table. Unlike a conventional analog-tuned oscillator, its frequency, phase, and modulation characteristics are controlled through a digital interface. The AD9852 applies this architecture to create an agile single-tone or modulation-capable output while retaining deterministic frequency programming and phase control. The principal features include a 300 MSPS internal clock rate, a 12-bit DAC, and a 48-bit tuning word for frequency resolution. The current-output DAC can produce up to 20 mA, while approximately 10 mA nominal output current provides the best spurious-free dynamic range. Output compliance is limited to -0.5 V to +1 V, making output-biasing and external analog filtering important parts of the implementation. Technically, the AD9852 combines digital synthesis and high-performance conversion in one CMOS device. Its phase accumulator determines the digital phase presented to the conversion path, while the internal DAC converts the calculated waveform into current. The external RSET resistor controls the full-scale DAC current according to the stated relationship RSET = 39.93/IOUT, with IOUT expressed in amperes. This integration reduces the number of external high-speed components required for a programmable source. Typical applications include communications test equipment, frequency-agile signal generation, clock synthesis, modulation systems, industrial instrumentation, and laboratory signal sources. Its extended industrial temperature range of -40°C to +85°C also supports equipment designed for controlled industrial environments. The internal DAC output is normally followed by reconstruction filtering when a clean sinusoidal waveform is required. Design should account for the DAC output-current limit, -0.5 V to +1 V compliance range, reference accuracy, and the package thermal requirements. Keep the analog output path short, place the RSET resistor close to the device, and design the reconstruction filter for the operating range. The Analog Devices AD9852 data sheet, Rev. F, is the controlling document for connection, timing, and electrical-limit details. This product record combines the verified manufacturer specifications, exact package information, source-document links, commercial contact workflow, and engineering-oriented application guidance. It also identifies the confirmed pin-compatible family relationship while clearly separating direct replacement options from parts that require a different footprint.
AD9854AST - 300 MSPS Quadrature DDS | Analog Devices
The Analog Devices AD9854AST is a production CMOS direct digital synthesis (DDS) device with two internal high-speed, high-performance quadrature DACs, forming a digitally programmable I and Q synthesizer. It supports operation up to 300 MSPS, uses 12-bit parallel or serial programming, and is housed in an 80-lead LQFP package. The device combines a phase accumulator, frequency tuning word, phase-control word, and dual DAC outputs in one integrated circuit. A direct digital synthesizer is a frequency-generation technique in which a digital phase accumulator determines the instantaneous output phase and a lookup process converts that phase into a sampled waveform. In the AD9854, two DAC paths provide independently programmable I and Q outputs. This architecture is useful when a system requires coherent quadrature signals, digitally adjustable frequency, or programmable phase control for communications, instrumentation, or signal-generation equipment. Key device capabilities include a 300 MSPS production CMOS implementation, 12-bit DAC resolution, parallel or serial data loading, and a 48-bit tuning capability identified in the manufacturer product listing. The AD9854 is also described as a complete quadrature DDS, allowing the two DAC outputs to support complex waveform generation rather than requiring separate external DACs. Its operating temperature range is specified as −40°C to +85°C, and the manufacturer lists the AD9854 as pin-for-pin compatible with the AD9852 single-tone synthesizer. The AD9854AST uses a 48-lead or 80-lead-style leaded quad flat pack configuration as identified by the target ordering code and product listings. The exact exposed-pad, pin, and electrical details should be confirmed against the AD9854 manufacturer datasheet before PCB release. The package provides a practical interface for external clocking, reference clock, programming data, synchronization, and analog I/Q outputs. Typical uses include RF and IF signal generation, communications test equipment, radar and electronic-warfare systems, arbitrary waveform generation, frequency synthesis, and phase-sensitive measurement. The two DAC outputs are particularly valuable when a system needs baseband quadrature signals for later upconversion or modulation. Design attention should be paid to clock jitter, reference-clock quality, analog output filtering, supply sequencing, and the relationship between the update rate and output bandwidth. A DDS output is sampled, so a reconstruction or anti-imaging filter is normally required before the outputs are used as final analog signals. Use the manufacturer datasheet for the complete pin description, recommended application circuit, and timing constraints.
AD9858BSV - 1 GSPS 10-Bit DDS | Analog Devices | RF Synthesis
Analog Devices AD9858BSV is a 1 GSPS direct digital synthesizer with an internal 10-bit DAC, housed in a 100-lead TQFP exposed-pad package measuring 14 mm by 14 mm. It generates digitally programmable sine-wave signals up to 400 MHz and includes a 32-bit tuning word for frequency control. The device also accepts an external reference clock as high as 2 GHz through its divide-by-2 clock input. A direct digital synthesizer, or DDS, is a frequency-generation architecture that uses a digital phase accumulator, phase-to-amplitude conversion, and a DAC to produce a digitally controlled analog output. Unlike a conventional analog oscillator whose frequency is adjusted with component tolerances, a DDS derives output frequency from a digital tuning word and reference clock. The AD9858BSV therefore belongs to the frequency synthesizer hierarchy, combining clock generation, digital signal synthesis, and data conversion functions in one integrated circuit. The AD9858BSV combines a 1 GSPS internal DAC, 32-bit frequency tuning, and an analog output capable of reaching 400 MHz. Its 10-bit DAC resolution provides 1024 amplitude steps, while the 32-bit tuning word supports precise digital frequency programming. The input-reference divider permits operation with reference-clock rates up to 2 GHz. These characteristics make the device suitable for RF signal generation, waveform testing, communications equipment, and frequency-synthesis subsystems. Technically, the AD9858BSV combines advanced DDS technology with a high-speed internal DAC. This integration removes the need for a separate DAC in conventional direct digital synthesis architectures and allows phase, frequency, and amplitude-related functions to be controlled digitally. The exposed thermal pad under the 100-lead package provides the primary heat-spreading path during operation, making PCB thermal design and via placement important at elevated update or output rates. Typical uses include swept-sine-wave generation for receiver testing, local-oscillator implementations in communications equipment, programmable clock and waveform sources for automated test systems, and reference-generation circuits in RF instrumentation. Its output frequency is set through a serial programming interface, allowing multiple instruments or embedded systems to share a common control architecture while synthesizing different frequencies. Designers should treat the exposed pad, analog output network, reference-clock integrity, and serial interface as one complete high-frequency subsystem. The manufacturer data sheet specifies the 3.3 V operating supply, the pin configuration, bypass requirements, and output implementation details. Decoupling should follow the manufacturer recommendations, and the analog output should be evaluated for filtering, amplitude calibration, and unwanted harmonic content before use in precision RF measurements. This page organizes the AD9858BSV specifications, sourcing information, comparison points, and application guidance around the manufacturer's published device characteristics. It also distinguishes the exact AD9858BSV ordering code from the closely related AD9858BSVZ and identifies where design verification must rely on the complete manufacturer data sheet and pin-description tables.
AD9859YSV - 400 MSPS 10-Bit DDS | Analog Devices
Analog Devices AD9859YSV is a 400 MSPS, 10-bit direct digital synthesis IC with an integrated DAC, a 32-bit tuning word, and a 48-lead TQFP exposed-pad package. It operates from a 1.8 V CMOS core supply, accepts 3.3 V CMOS I/O, and generates digitally programmable output frequencies with phase and amplitude dithering. The internal high-speed DAC provides greater than 75 dB SFDR at a 160 MHz output with a ±100 kHz measurement offset. A direct digital synthesizer, or DDS, is a programmable waveform generator that uses a phase accumulator and a phase-to-amplitude conversion process to synthesize a sine wave. The DDS belongs to the signal-generation hierarchy and combines digital frequency control with an analog output stage. In the AD9859YSV, the digital synthesis engine and 10-bit DAC operate together to provide a complete single-chip signal source with a 32-bit frequency-control word. Key features include a 400 MSPS internal clock speed, a 10-bit DAC, serial I/O control, programmable phase and amplitude dithering, software and hardware power-down control, and a phase-noise specification of no more than −120 dBc/Hz at a 1 kHz offset. The device also includes a reference-clock multiplier with selectable multiplication ratios beginning at 4× and supports 5 V input levels on most digital inputs. The AD9859YSV can operate from an external reference clock or use its on-chip oscillator with an external crystal connected to REFCLK and REFCLKB. A 20 MHz external reference with the multiplier enabled at 20× provides the stated operating condition. The internal reference-clock multiplier extends usable input-reference flexibility, while the 32-bit tuning word permits fine frequency increments across the output range. The serial interface allows the tuning word and operating functions to be programmed by an embedded controller. Typical uses include local oscillator and reference-clock generation, signal generators, communications test equipment, frequency-hopping systems, waveform synthesis, and automated measurement systems. Its integrated DAC simplifies architectures that would otherwise require a separate high-speed converter. The 10-bit resolution provides a practical balance between output fidelity, interface complexity, and implementation cost for many communication and instrumentation applications. Design attention should focus on the analog output reference, clock cleanliness, power-supply sequencing, and exposed-pad thermal management. The DAC output must be referenced to AVDD rather than AGND. Short, impedance-controlled routing from the reference source and careful treatment of return paths are important for preserving phase-noise and spurious performance. The exposed pad should be connected to the ground plane using an appropriate thermal and layout strategy. This page combines the verified AD9859YSV specifications, package information, pricing record, replacement analysis, and practical application guidance into an engineering-focused resource. It also distinguishes the electrically similar package and order-code variants from genuine drop-in alternatives, helping designers make informed schematic, footprint, sourcing, and signal-integrity decisions.
AD9901KP - 200 MHz Phase/Frequency Discriminator | Analog Devices
The Analog Devices AD9901KP is an ultrahigh-speed digital phase/frequency discriminator that directly compares phase and frequency inputs up to 200 MHz, and the KP commercial version is supplied in a 20-pin PLCC package. According to the manufacturer product page, AD9901 devices are also offered in a 14-pin ceramic DIP, while versions compliant with MIL-STD-883 are available through the military-product documentation. A phase/frequency discriminator is a timing IC that measures the phase relationship and frequency difference between two signals and represents the result as a digital error word. Within the broader clock and timing hierarchy, the AD9901KP belongs to comparator and phase-detection logic used by synchronous communication, modulation, synthesis, and control systems. Its role is to convert two high-speed input signals into an error indication that an upstream clock, phase-locked loop, delay controller, or feedback system can use for correction. The AD9901 architecture combines an ultrahigh-speed trench-oxide isolated process with a detection approach described by Analog Devices as providing a linear detection range without the indeterminate phase-detection zones common to other digital designs. The verified source states that inputs can be compared directly to 200 MHz. Concrete operating voltage, supply-current, output-logic, input-logic-threshold, setup-time, propagation-delay, temperature-range, and electrical-limit values were not included in the supplied search results and therefore require confirmation from the manufacturer datasheet before design release. The AD9901KP is suited to high-speed clock distribution, phase-error detection, digital frequency comparison, communications timing, and feedback-control systems where two related signals must be compared without first reducing them to a lower frequency. In a PLL or delay-control loop, the discriminator output can represent phase or frequency error so that the controlling loop can adjust a clock generator, delay line, or oscillator. Designers must account for input thresholds, propagation delay, output decoding, setup and hold requirements, supply rails, and package-level routing. PLCC is a leaded surface-mount package in the PLCC family, but the supplied data does not expose the exact package dimensions, pin names, exposed pad arrangement, thermal resistance, or recommended land pattern. The public data does identify a 20-pin PLCC for the commercial family, yet it does not provide a complete AD9901KP pin map; engineers should use the official AD9901 datasheet rather than infer pin functions from a generic PLCC footprint. This page consolidates the verified 200 MHz input-comparison capability, package-family information, sourcing links, and replacement-availability constraints for AD9901KP. Contact XAIPART for current quotation, formal availability, traceability, and lot-specific commercial terms. Pricing shown for the single-unit tier reflects the cited marketplace value as of 2026-10-23 and should be reconfirmed before procurement.
AD9901KQ - 200MHz Phase/Frequency Discriminator | Analog Devices
The Analog Devices AD9901KQ is a digital phase/frequency discriminator IC that directly compares phase or frequency inputs up to 200 MHz, with one discriminator channel in a 14-CDIP ceramic DIP package measuring 0.300 inches (7.62 mm). It is intended for high-speed frequency comparison, phase detection, clock alignment, and instrumentation applications where a linear detection range is required. A digital phase/frequency discriminator is a timing IC that compares two periodic signals and produces an error indication representing their relative phase and frequency. Within the broader hierarchy of clock and timing integrated circuits, it combines input frequency comparison with phase-error generation. Unlike simple binary phase comparators, the AD9901 is designed to avoid the indeterminate detection zones associated with many digital phase-detection implementations. The AD9901 uses a high-speed trench-oxide isolated process to compare inputs directly to 200 MHz. According to the manufacturer datasheet, its innovative architecture provides a linear detection range, making it useful in closed-loop clocking, phase-locked-loop error paths, frequency-discriminator instrumentation, and laboratory signal-chain designs. The commercial AD9901 family is also offered in a 20-pin PLCC package, while the AD9901KQ specifically uses the 14-pin ceramic DIP. Typical uses include comparing a reference oscillator against a signal under test, generating phase-error voltage for servo loops, evaluating frequency drift, and supporting clock-distribution alignment. In these systems, the discriminator can operate directly at the stated 200 MHz input limit, reducing the need for external prescaling when signals remain within range. One key design consideration is that available verified data identifies the function, maximum input frequency, package, and commercial or military product options, but does not provide a complete electrical table, individual pin map, supply-voltage range, or output characteristics. Those values should therefore be confirmed in the manufacturer datasheet before final circuit implementation. Ceramic-DIP construction and the absence of verified lead-free or environmental declarations should also be considered during lifecycle planning. This page combines the verified manufacturer and distributor information for AD9901KQ with application guidance, comparison parameters, and engineering-oriented cautions. It is intended to help engineers identify the correct function, package, operating class, and sourcing path without presenting unsupported electrical claims.
AD9951YSV - 400 MSPS 14-Bit DDS | Analog Devices
The Analog Devices AD9951YSV is a 400 MSPS, 14-bit direct digital synthesis IC with a 32-bit tuning word, a 1.8 V CMOS supply, and a 48-lead TQFP-EP package measuring 7 mm by 7 mm. It combines a high-speed programmable frequency synthesizer with an integrated 14-bit DAC for digitally controlled waveform generation. A direct digital synthesizer, or DDS, is a frequency-generation technique in which a digital phase accumulator advances a phase word at a controlled clock rate, and the resulting phase address selects an amplitude value from a lookup table. Unlike a conventional analog local-oscillator chain, a DDS supports digitally programmed frequency, phase, and amplitude adjustments through a serial interface while retaining high frequency stability derived from its reference clock. The AD9951YSV provides a 400 MSPS internal clock, a 32-bit frequency-tuning word, and a 14-bit output DAC. Its phase noise is specified at -120 dBc/Hz at a 1 kHz offset from the DAC output. Dynamic performance includes greater than 80 dB spurious-free dynamic range at 160 MHz with a 100 kHz offset. Serial I/O controls the device, while an AOUT output provides the analog result. The 1.8 V CMOS architecture supports low-voltage integration with high-speed digital systems. The internal architecture separates frequency and phase accumulation from the DAC conversion path, allowing the frequency tuning word, phase offset, and amplitude scale factor to be loaded independently. This architecture supports rapid frequency hopping, precise channel selection, and calibrated phase control. An on-chip oscillator can operate with an external crystal connected to the REFCLK and REFCLKB inputs, with a reference-clock range of 20 MHz to 30 MHz specified for that configuration. Typical applications include communications test equipment, frequency synthesizers, clock-generation modules, digital waveform sources, and local-oscillator subsystems. The device is also appropriate for radar, instrumentation, and phased-array signal chains where digitally controlled phase adjustment improves channel alignment. When laying out a circuit, treat the reference clock, serial interface, and analog output as separate high-speed paths. Route the exposed-pad thermal connection through the package thermal design, and use a controlled impedance connection for the analog output to avoid reflections or unwanted harmonics. This page combines device specifications, practical integration guidance, sourcing information, and verified alternatives. It also identifies the electrical and pinout details that should be checked in the manufacturer data sheet before a new PCB layout is released.
AD9952YSV - 400 MSPS 14-Bit DDS | Analog Devices
The Analog Devices AD9952YSV is a 400 MSPS direct digital synthesizer with an integrated 14-bit DAC, 32-bit tuning word, and high-speed comparator in a 48-lead TQFP exposed-pad package. The device operates from a 1.8 V CMOS supply and combines digital phase accumulation with a high-performance DAC to generate precisely controlled analog output signals. It is recommended by Analog Devices for new designs. A direct digital synthesizer, or DDS, is a frequency synthesizer that generates an output waveform from phase and frequency data rather than relying entirely on a conventional analog oscillator loop. In the signal hierarchy, the AD9952 belongs to the DDS family within clock and timing ICs, combining a digital phase accumulator, tuning-word registers, a DAC, and a comparator. This architecture provides digital frequency, phase, and amplitude control while retaining a conventional analog output. Principal features include an internal clock rate of 400 MSPS, a 14-bit DAC, programmable phase and amplitude dithering, and a 32-bit frequency tuning word. The DAC output phase noise is specified at 125 dBc/Hz with a 1 kHz offset. Dynamic performance reaches 80 dB SFDR at a 130 MHz output with a 100 kHz offset. An integrated high-speed comparator allows the device to provide a digital clock output in addition to its analog I/O functions. Technically, the AD9952 generates a stepped approximation to a sine wave at the selected output frequency. The 32-bit tuning word defines the phase increment applied by the phase accumulator, while the 14-bit DAC converts the accumulated phase into an analog voltage. Phase and amplitude dithering can spread quantization energy away from the carrier, improving spectral purity in demanding signal-generation systems. The high-speed internal architecture supports demanding waveform generation, clock synthesis, and frequency conversion applications. Typical uses include communications test equipment, local oscillators, digital waveform generation, clock synthesis, tunable filters, and frequency-agile RF subsystems. The 400 MSPS operating rate and 14-bit output resolution are particularly useful when compact instrumentation must combine fine frequency resolution with high update and comparison rates. The main design consideration is package and layout planning. The exposed pad requires careful connection to ground and adequate thermal copper, while the analog and digital supply paths must be decoupled close to their respective pins. High-speed output edges can couple into adjacent circuitry, so return-current paths and output routing deserve attention during PCB implementation. This product overview combines manufacturer specifications, package details, application guidance, replacement considerations, and practical layout notes to support faster component selection and first-pass PCB planning.
AD9953YSV - 400 MSPS 14-Bit DDS | Analog Devices | Signal Generation
Analog Devices AD9953YSV is a 1.8 V CMOS direct digital synthesizer, or DDS, featuring a 14-bit internal DAC that operates up to 400 MSPS. The device combines digital phase accumulation, a 32-bit tuning word, and high-speed DAC output in a 48-lead TQFP package with an exposed pad. These headline characteristics position it for precision signal generation, waveform synthesis, communications test equipment, and digitally controlled frequency conversion. A direct digital synthesizer is a programmable waveform generator in the broader signal-generation and clock-and-timing hierarchy. Unlike a traditional analog oscillator whose frequency and phase are adjusted mainly by analog components, a DDS derives its output from a digital phase accumulator. AD9953YSV integrates that digital engine with a high-speed DAC, allowing frequency, phase, and amplitude-related functions to be managed through a serial control interface. The principal features are a 400 MSPS maximum DAC update rate, a 14-bit DAC resolution, and a 32-bit tuning word. The 32-bit tuning word provides fine frequency-addressing granularity, while the 14-bit DAC establishes the output word length. The 1.8 V CMOS supply arrangement supports integration into modern low-voltage digital systems. Its 48-TQFP-EP construction, measuring 7 x 7 mm, offers a compact surface-mount implementation with an exposed thermal pad. In operation, the AD9953 generates a sampled waveform and converts the digital sequence through its internal DAC. The externally controlled phase accumulator determines the frequency setting, while the serial interface programs device parameters. This architecture separates digital frequency control from the analog output path, making it useful when repeatable frequency changes, rapid retuning, or compact instrument control are important. Typical applications include communications test and measurement, local oscillator generation, waveform synthesis, signal analyzers, and embedded RF test systems. In these systems, the AD9953 can generate a digitally specified output while the surrounding controller manages calibration, modulation, and test sequencing. The 400 MSPS operating rate also makes the device relevant to high-speed waveform generation and clocking architectures. Board design must treat the analog output path, digital interface, supply distribution, and exposed pad as an integrated high-speed system. Short output routing, a stable reference implementation, adequate ground-plane continuity, and careful decoupling help preserve DAC performance. The exposed pad should be connected according to the manufacturer’s package guidance and thermal/layout recommendations. This product page organizes the AD9953YSV’s confirmed operating characteristics, sourcing information, package details, design considerations, and application guidance. It also distinguishes the exact AD9953YSV order code from related package and reel-order variants so engineers can assess footprint compatibility without assuming that every similarly named suffix is interchangeable without verification.
AD9954YSV - 400 MSPS 14-Bit DDS IC | Analog Devices
Analog Devices AD9954YSV is a 400 MSPS, 14-bit, 1.8 V CMOS direct digital synthesizer in a 48-lead TQFP with exposed pad. It combines a high-speed internal DAC, phase-to-frequency conversion logic, static RAM, and a high-speed serial programming interface to generate digitally programmable, frequency-agile output signals. A direct digital synthesizer, or DDS, is a programmable waveform-generation architecture that converts a phase word into a frequency-accurate output. A DDS belongs to the clock-and-timing IC hierarchy alongside frequency synthesizers, waveform generators, and clock-generation devices. Its digital tuning architecture enables frequency, phase, and sweep control through a serial bus while retaining direct digital programming. The AD9954 supports 400 MSPS operation, a 14-bit DAC, and 32-bit tuning. Static RAM enables several frequency-sweep modes, including a user-defined linear sweep. An on-chip high-speed comparator supports square-wave output requirements, while the integrated oscillator and phase-locked-loop circuitry provide additional clock-generation approaches for system architectures that need a local reference or multiplied source. The device is programmed through a high-speed serial I/O port, allowing a host controller to load tuning words and configuration commands while the synthesizer remains under firmware control. This architecture is useful when the output frequency must change rapidly or follow a digitally calculated sequence. The exposed thermal pad supports heat transfer from the high-performance device to the PCB copper area, although thermal performance still depends on layout, ambient temperature, and dissipation. Typical uses include tunable signal sources, frequency-agile test equipment, communications waveform generation, local oscillator generation, and instrumentation requiring precise digital frequency control. The DDS architecture is especially useful when multiple operating modes or stored sweep profiles are needed without relying on a separate waveform-memory device. A critical design consideration is to use the pin description, power-supply requirements, and recommended decoupling directly from the Analog Devices data sheet when assigning a PCB footprint. The exposed pad must be connected according to the device recommendations, and high-speed serial routing should be kept short with a controlled return path. This page combines the AD9954YSV device characteristics, sourcing information, replacement guidance, comparison parameters, and practical design notes in one engineering-focused reference. It also identifies where a true pin-compatible substitution must be checked against the complete data sheet before production use.
AD9959BCPZ - 4-Channel 500 MSPS DDS | Analog Devices
The Analog Devices AD9959BCPZ is a four-channel direct digital synthesis clock generator with 500 MSPS operation, 10-bit DACs, independent frequency, phase, and amplitude control, and a 56-lead 8 mm × 8 mm LFCSP package. The device uses a 1.8 V DDS-core and digital-interface supply arrangement with a 3.3 V SPI interface, and it operates from −40°C to +85°C. A direct digital synthesizer, or DDS, is a clock-and-waveform-generation IC that creates a digitally programmable output frequency from a reference clock and phase accumulator. DDS devices combine digital frequency control with analog output filtering and are commonly used when engineers need agile, accurate, or multi-channel coherent frequency generation. The AD9959 places four synchronized DDS channels, four 10-bit DACs, programmable tuning, and a serial control interface into one integrated component. The AD9959 provides independent frequency, phase, and amplitude control for each channel while sharing a common system clock. This synchronization is useful when several outputs must maintain matched latency during tuning. The 500 MSPS DAC rate supports high-speed signal generation, while the 32-bit tuning field is identified in the verified distributor data. The 10-bit output resolution is suitable for applications where compact, programmable waveform generation is more important than very high spectral purity. Each channel includes a 10-bit digital-to-analog converter, allowing the device to generate independently controlled analog outputs from common digital timing. This architecture can reduce the component count compared with separate oscillators and DACs, particularly in instrumentation, communications, and test systems. The common system clock also makes coherent frequency relationships and phase alignment easier to maintain across channels. Typical applications include agile local oscillators, test and measurement equipment, communications infrastructure, signal-generation systems, and synchronized multi-channel waveform generation. The AD9959 is recommended by Analog Devices for new designs according to the verified manufacturer page, and its 56-lead LFCSP package is intended for surface-mount PCB designs. The primary design considerations are supplying the required core and I/O rails, connecting the SPI interface at the appropriate logic voltage, and filtering each DAC output appropriately. The package has 56 leads, but the exact exposed-pad and thermal-land requirements must be taken from the manufacturer datasheet during layout. The verified data identifies the package as 56-LFCSP-VQ, while the canonical package key is qfn-56 because the available library does not include a 56-lead LFCSP entry. This page combines verified Analog Devices and distributor information with package, application, comparison, and design guidance. Exact pin names, voltage tolerances, output-current limits, RoHS status, REACH status, and lead-time terms were not present in the supplied verified data and are therefore not guessed here.
ADF4001BCP - 200 MHz PLL Clock Generator | Analog Devices
The Analog Devices ADF4001BCP is a 200 MHz frequency synthesizer and clock generator with programmable reference and feedback division, a low-noise digital phase-frequency detector, and a precision charge pump. It operates from a 2.7 V to 5.5 V power supply, supports a separate charge-pump supply for extended tuning-voltage headroom, and is packaged in a 16-lead TSSOP package. A frequency synthesizer is a phase-locked-loop, or PLL, device that compares a reference signal with a divided feedback signal and drives an external voltage-controlled oscillator or voltage-controlled crystal oscillator through a charge pump and loop filter. The ADF4001 belongs to the broader clock and timing IC hierarchy, where it combines frequency generation, programmable division, phase detection, and charge-pump output for stable, low-noise clock architecture. Key features include 200 MHz bandwidth, programmable charge-pump currents, a 3-wire serial interface, hardware and software power-down modes, analog and digital lock detection, and a typical operating current of 4.5 mA. The separate VPD charge-pump supply allows greater tuning-voltage range in systems operating from a 5 V supply. The interface is compatible with the ADF4110, ADF4111, ADF4112, and ADF4113 family, supporting familiar control and clock-tree design practices. Internally, the device uses a low-noise digital phase-frequency detector, a precision charge pump, a programmable reference divider, a programmable 13-bit N counter, and a 14-bit reference counter. These counters allow the reference and feedback paths to be adjusted so that the synthesized output can be related accurately to the incoming reference. The ADF4001 is intended for clock sources requiring low phase noise and stable reference signals rather than for directly driving a high-power RF output stage. Typical uses include low-noise clock generation, frequency synthesis, communication-clock distribution, instrumentation timing, and reference-clock multiplication or division. In a common implementation, the charge-pump output drives an external loop filter and voltage-controlled crystal oscillator, while the oscillator output is fed back to the RF input. Designers should also account for loop bandwidth, reference stability, component tolerances, charge-pump leakage, and the power-supply requirements of the separate charge-pump rail. The most important design consideration is loop-filter implementation because the charge-pump current, reference divider, N counter, and oscillator tuning range jointly determine phase noise and lock behavior. Place the serial-interface traces away from sensitive feedback and charge-pump paths, provide stable supply decoupling, and use a clean low-noise reference. Verify lock-detect behavior across temperature and supply variation before relying on it for system sequencing. This page consolidates verified manufacturer specifications, current distributor pricing, and practical replacement guidance with the ADF4001BCP. The alternative analysis distinguishes genuine pin-compatible options from related PLL products that may require different packages, divider ratios, or tuning ranges, helping engineers evaluate a replacement without relying on part-number similarity alone.
ADF4001BCPZ - 200MHz PLL Clock Generator | Analog Devices
Analog Devices ADF4001BCPZ is a 200 MHz fractional-N clock generator and phase-locked-loop synthesizer with a 2.7 V to 5.5 V supply range, operating current of 4.5 mA, and a 20-pin WFQFN/LFCSP exposed-pad package. It provides a programmable reference divider, programmable 13-bit N counter, 14-bit reference counter, precision charge pump, and low-noise digital phase-frequency detector for stable clock synthesis. A PLL frequency synthesizer generates a precise output frequency by comparing an input reference with a divided feedback signal. The phase-frequency detector converts phase error into a control signal, while the charge pump and loop filter establish the tuning voltage applied to a voltage-controlled oscillator. Within the broader semiconductor hierarchy, the ADF4001 belongs to the clock and timing category, where it functions as a frequency synthesizer, clock generator, and phase-locked loop. Key features include a 200 MHz maximum synthesis bandwidth, separate charge-pump supply that permits extended tuning voltage in 5 V systems, programmable charge-pump currents, and a three-wire serial interface. The separate VP connection allows the tuning range to be tailored to the oscillator used in the design. Analog and digital lock detection help system logic identify when the loop has acquired lock. The architecture supports low-noise clock generation from a stable external reference. The programmable reference and feedback counters set the required multiplication and division ratios, while the charge-pump settings influence loop bandwidth, phase noise, and lock behavior. Typical operating current of 4.5 mA also makes the device suitable for power-conscious instrumentation and communication equipment. Typical applications include clock sources for phase-locked loops, communications infrastructure, frequency synthesis for RF signal chains, precision test and measurement equipment, and low-noise local oscillators. A suitable design must provide a clean reference signal, configure the serial registers correctly, and select a loop filter and VCO suitable for the target frequency. For PCB implementation, place the decoupling capacitors and the exposed-pad thermal connection close to the device, keep the reference and RF input routing compact, and avoid routing high-speed or high-current switching signals beneath the package. Check the voltage at the charge-pump supply because the separate VP pin is central to extending tuning-voltage headroom. This page combines the manufacturer specifications, package details, interface characteristics, and practical PLL design considerations to help engineers evaluate the ADF4001BCPZ for clock-generation and frequency-synthesis designs.
ADF4001BRU - 200 MHz Clock Generator PLL | Analog Devices
Analog Devices ADF4001BRU is a 200 MHz clock generator phase-locked-loop (PLL) IC with a 2.7 V to 5.5 V power supply and a 16-lead TSSOP package. Its typical operating current is 4.5 mA, and its 3-wire serial interface supports programmable clock generation and frequency synthesis. A separate charge-pump supply permits extended tuning voltage in 5 V systems, while programmable charge-pump currents provide control over loop behavior. A clock generator PLL is a frequency-control IC that compares a reference signal with a divided feedback signal and drives a tunable oscillator toward phase and frequency lock. Within the broader semiconductor hierarchy, the ADF4001 belongs to the clock and timing IC family and functions as a programmable frequency synthesizer for systems requiring a stable, low-noise reference clock. Its internal blocks include a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, 13-bit N counter, and 14-bit R counter. Key features include 200 MHz bandwidth, programmable charge-pump currents, hardware and software power-down modes, and analog and digital lock detection. The separate charge-pump supply, designated Vp in the manufacturer data, supports extended tuning voltage in systems operating from 5 V. Hardware compatibility with the ADF4110, ADF4111, ADF4112, and ADF4113 families helps simplify software migration across related Analog Devices PLL designs. The architecture allows the reference frequency to be divided through the R counter and the feedback frequency through the N counter. The phase-frequency detector and charge pump translate phase and frequency errors into a tuning correction for the controlled oscillator. Serial programming provides access to the counters and charge-pump settings, while the analog and digital lock indicators allow a host controller to monitor synchronization status. Typical uses include low-noise clock sources for RF and microwave PLL systems, frequency synthesis in communications equipment, clock generation for instrumentation, and reference-clock distribution where programmable division is useful. The 16-lead TSSOP package is suitable for conventional surface-mount assembly, while the 2.7 V to 5.5 V supply range accommodates both lower-voltage and 5 V designs. Designers should treat the charge-pump, loop-filter, and reference-divider settings as a coordinated system. The separate Vp connection must be decoupled according to the manufacturer's guidance, and the serial interface must preserve the required timing while counters and lock functions are programmed. Because the provided source data does not provide a complete pin map, engineers should verify every connection against the official ADF4001 data sheet before layout release. This product summary consolidates the verified manufacturer specifications, current manufacturer pricing, package information, and engineering guidance for the ADF4001BRU. It also distinguishes verified device data from unavailable details, helping procurement and design teams avoid assumptions about pinout, operating temperature, compliance, or alternative-part compatibility.
ADF4001BRUZ - 200 MHz Low-Noise Clock Generator PLL | Analog Devices
The Analog Devices ADF4001BRUZ is a 200 MHz bandwidth clock generator and phase-locked loop (PLL) synthesizer built on a BiCMOS process and packaged in a 16-lead TSSOP (0.173 inch, 4.40 mm width). It operates from a 2.7 V to 5.5 V supply with a typical operating current of 4.5 mA and provides a separate charge pump supply (VP) for extended tuning voltage in 5 V systems. A PLL is a feedback control system in which a phase-frequency detector compares a reference clock against a divided output, a precision charge pump then converts the phase error into a control voltage, and a voltage-controlled oscillator (VCO) inside a voltage-controlled crystal oscillator (VCXO) loop closes the loop. Clock generator PLLs such as the ADF4001 are used to multiply a stable low-frequency reference into a clean, programmable, low-phase-noise output for clock trees, mixers, and local oscillators. Key features include a low-noise digital phase-frequency detector, a precision charge pump with programmable charge pump currents, a programmable 13-bit N counter, and a 14-bit R (reference) counter that allows selectable REFIN frequencies. The part also supports programmable charge pump currents, hardware and software power-down modes, and analog plus digital lock detect. The 3-wire serial interface provides simple register-based programming from a microcontroller or PROM. Architecturally, the ADF4001 combines a digital PFD, charge pump, programmable dividers, and counter logic that can be configured as a VCXO/VCXO-with-divide or a direct divide-by-N clock generator arrangement. A separate VP pin lets the tuning voltage swing above the main supply rail, a technique that widens the achievable tuning range in 5 V systems. The device is hardware compatible with the ADF4110, ADF4111, ADF4112, and ADF4113 PLL family, which simplifies firmware and board migration across the family. Typical applications include low-noise clock generation for RF transceivers, frequency synthesis for instrumentation and test equipment, clocking for high-speed data converters, and stable local oscillator generation in wireless receivers, measurement front ends, and industrial control systems. When designing with the ADF4001BRUZ, pay attention to reference input conditioning and loop filter design: use a clean, low-jitter reference at REFIN and select the N and R divider values to keep the PFD rate inside the range where phase noise is lowest. Keep the charge pump supply decoupling close to the VP pin to avoid noise injection into the tuning line. This page consolidates the manufacturer datasheet details, drop-in ordering alternatives, a parameter-by-parameter comparison, and practical design notes that help shorten evaluation time for engineers bringing up a new PLL-based clock or LO design.
ADF4001BRUZ-R7 - 200MHz PLL Clock Generator | Analog Devices
The Analog Devices ADF4001BRUZ-R7 is a 200 MHz clock-generator PLL with a 2.7 V to 5.5 V power supply, 4.5 mA typical operating current, and a 16-lead TSSOP package. It combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, 13-bit N counter, and 14-bit R counter to synthesize stable, programmable clock and PLL reference signals with low phase noise. An integrated PLL is a feedback-controlled frequency synthesizer that compares a reference signal with a divided feedback signal, drives an external voltage-controlled oscillator or voltage-controlled crystal oscillator through a charge pump and loop filter, and locks the output to a stable frequency. Clock-generator PLLs belong to the broader clock and timing IC hierarchy and are used where a fixed or divided system clock is insufficient and precise, programmable frequency generation is required. The ADF4001 supports reference input frequencies that can be selected through its programmable reference divider. Its separate charge-pump supply permits a higher tuning voltage in 5 V systems, while programmable charge-pump currents provide flexibility when tuning loop-filter behavior. Hardware and software power-down modes help reduce consumption when the synthesizer is not required. Analog and digital lock-detect outputs allow a controller to monitor whether the loop has acquired the intended frequency. A three-wire serial interface provides programming access for the counters and control functions. The device includes a low-noise digital phase-frequency detector and precision charge pump, supporting low-noise clock generation and stable PLL reference sources. The 16-lead TSSOP package is compatible with the ADF4110, ADF4111, ADF4112, and ADF4113 family according to the manufacturer datasheet, which can simplify platform qualification and board-level standardization. Typical uses include wireless-infrastructure reference clocks, instrumentation clocks, low-frequency RF synthesizers, clock-cleaning systems, and communication equipment requiring programmable division or multiplication. In a VCXO-based design, the charge-pump output drives the loop filter and tuning input of the oscillator, while the oscillator output feeds the RF input and reference path through suitable matching. PCB design should keep the serial programming traces away from sensitive RF and charge-pump paths, provide solid ground-plane continuity, and place loop-filter components close to the charge-pump and VCO-related pins. Designers must also observe the difference between the 2.7 V to 5.5 V device supply and the separately supplied charge-pump voltage, particularly when operating in a 5 V system. This page combines the manufacturer specifications with practical PLL design guidance, package-level pin information, application examples, and a structured comparison of genuine same-package alternatives for engineers evaluating clock-generator upgrades.
ADF4002BCPZ - 400 MHz PLL Frequency Synthesizer | Analog Devices
The Analog Devices ADF4002BCPZ is a phase detector and PLL frequency synthesizer with a 400 MHz maximum input frequency, supplied in a 20-lead WFQFN exposed-pad package. It operates from a 3.3 V power supply and includes a separate charge-pump supply that allows the tuning voltage to be extended. The device also provides programmable charge-pump currents and a 3-wire serial interface for configuration and control. A PLL frequency synthesizer is a timing-control integrated circuit that locks an output frequency to a stable reference frequency. Its phase-frequency detector compares the divided feedback signal with the reference signal, while the charge pump converts phase error into a tuning voltage for an external voltage-controlled oscillator or voltage-controlled crystal oscillator. In the broader semiconductor hierarchy, the ADF4002 belongs to the clock and timing IC family and ultimately to the PLL and frequency-synthesizer category. The ADF4002 integrates a low-noise digital phase-frequency detector, a precision charge pump, a programmable reference divider, and a programmable N divider. According to the Analog Devices product page, the 14-bit reference counter supports selectable reference-input frequencies. Programmable charge-pump currents give the circuit additional control when optimizing loop behavior, reference spur performance, and phase noise for a particular synthesizer implementation. The 400 MHz input bandwidth makes the ADF4002 relevant to wireless receiver and transmitter local-oscillator paths, especially up-conversion and down-conversion stages. Its architecture supports integer-N frequency synthesis. The separate VP charge-pump supply is useful when the required oscillator tuning range exceeds the normal operating range of the main power rail, while the 3.3 V supply architecture supports compact RF and communications systems. Typical uses include wireless transceiver local oscillators, receiver and transmitter up-converters and down-converters, frequency-locked reference sources, and other RF signal chains requiring programmable division and phase correction. Engineers should preserve the exposed-pad grounding and supply-decoupling layout shown in the manufacturer datasheet. The serial interface uses CLK, DATA, and LE signals, and 24-bit words are transferred on rising clock edges when latch enable is asserted. Because this is an external-VCO PLL rather than a complete integrated RF synthesizer, component selection, loop-filter design, reference stability, and VCO phase-noise performance remain external design tasks. The separate charge-pump supply also requires careful decoupling and isolation from sensitive RF and reference circuitry. This page combines the verified Analog Devices product information, distributor listings, package details, design considerations, commercial availability, and a documented assessment of drop-in replacement evidence. The verified sources do not identify five pin-to-pin-compatible alternatives, so the alternatives list is intentionally limited rather than padded with unsupported cross-package or packaging-only substitutes.
ADF4002BCPZ-RL7 - 400 MHz Phase Detector PLL | Analog Devices
The Analog Devices ADF4002BCPZ-RL7 is a 400 MHz phase-detector and frequency-synthesizer IC in a 20-lead WFQFN exposed-pad package. It supports reference frequencies up to 4 GHz and combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, programmable N divider, and 14-bit reference counter. The device is designed to generate local-oscillator signals for wireless receiver and transmitter up-conversion and down-conversion stages. A phase-locked loop, or PLL, is a feedback-control circuit that locks an output oscillator to a stable reference frequency. Within the broader clock and timing hierarchy, the ADF4002 combines phase detector, frequency divider, charge pump, and synthesizer functions in one clock-and-timing IC. Its programmable dividers allow a relatively low-frequency reference to be multiplied to a desired local-oscillator output while the phase-frequency detector and charge pump correct loop phase and frequency error. The principal feature of the ADF4002 is its 400 MHz phase-detector operating rate, which supports high-speed frequency-synthesis architectures. A programmable 14-bit R counter accommodates selectable reference-divider ratios, while the N divider sets the integer multiplication relationship between the reference and synthesized output. The low-noise digital phase-frequency detector and precision charge pump support loops intended for RF signal-chain applications where phase noise and reference spur behavior are important. Technical operation begins with the reference signal entering the programmable reference divider. The divided reference and divided feedback signal are compared by the phase-frequency detector. Their phase difference controls the charge pump, which drives the external loop filter and voltage-controlled oscillator. The resulting divided output is returned through the N divider, closing the feedback loop. Designers therefore need to select loop bandwidth, charge-pump current, filter components, and VCO characteristics according to the required phase noise and lock-time targets. Typical uses include wireless receiver local oscillators, transmitter up-conversion and down-conversion chains, RF transceiver synthesizers, instrumentation, and communication systems. The device is particularly relevant when a programmable phase detector is needed in a fractional-N or integer-N architecture without integrating the complete RF oscillator into the IC. The exposed pad requires careful PCB thermal design and grounding. Follow the manufacturer land pattern and reference layout, connect the exposed pad to the appropriate ground plane, and place decoupling and charge-pump components according to the datasheet guidance. Confirm loop stability and phase-noise performance with the actual VCO and filter rather than relying only on calculated divider ratios. This page organizes the verified electrical identity, package information, sourcing guidance, replacement constraints, and application-oriented engineering guidance. It also distinguishes true pin-compatible alternatives from package or reel-code variants that should not be treated as distinct drop-in designs.
ADF4002BRUZ - 400 MHz Integer-N PLL | Analog Devices
The Analog Devices ADF4002BRUZ is an integer-N phase-locked-loop frequency synthesizer with a maximum operating frequency of 400 MHz, a 3.3 V power supply, and a 16-lead TSSOP package. It combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, and programmable N divider for precision local-oscillator synthesis in wireless receivers, transmitters, and instrumentation. The ADF4002 family is recommended by Analog Devices for new designs. An integer-N PLL frequency synthesizer is a clock-and-timing semiconductor that locks an output frequency to a stable reference by comparing phase and frequency through a phase-frequency detector. A charge pump converts the detected error into a control voltage for a voltage-controlled oscillator, while programmable dividers establish the integer multiplication ratio. This architecture places the ADF4002 within the hierarchy of PLL, frequency synthesizer, clock generator, timing IC, and clock-and-timing semiconductor. The principal features include 400 MHz bandwidth, operation from a 3.3 V supply, a separate charge-pump supply that permits an extended tuning-voltage range, programmable charge-pump currents, and a 3-wire serial interface. A 14-bit reference counter supports programmable reference-frequency division, while the programmable N divider establishes the synthesis ratio used to derive the output frequency. These functions support direct digital control of frequency and phase in RF signal chains. The phase-frequency detector compares the divided reference signal with the divided feedback signal, and the charge pump generates the loop-control current required to null the phase and frequency error. The separate VP connection decouples the charge-pump voltage range from the main 3.3 V analog supply. This architecture is useful when a designer needs additional tuning-voltage headroom or a specific programmable charge-pump setting to balance loop bandwidth, reference phase noise, and settling behavior. Typical uses include wireless receiver and transmitter local oscillators, up-conversion and down-conversion sections, instrumentation requiring stable synthesized frequencies, and test equipment requiring a programmable clock. The 16-lead TSSOP package also supports compact, surface-mount designs where the board area must remain small without adopting a larger land pattern. For a new layout, preserve the manufacturer reference-network and decoupling topology, place the reference and feedback paths away from switching-node and charge-pump return currents, and verify loop settling with the intended reference frequency and divider settings. The available pin and electrical details should be taken directly from the pin-description and application tables in the ADF4002 manufacturer datasheet. This page combines the device function, verified product characteristics, application guidance, pricing workflow, and engineering trade-offs in one engineering-focused reference. It also distinguishes the 16-lead TSSOP implementation from other package options without treating a different package as a drop-in replacement.
ADF4002BRUZ-RL7 - 400MHz PLL Synthesizer | Analog Devices
The Analog Devices ADF4002BRUZ-RL7 is a 400 MHz phase detector and frequency synthesizer for wireless receiver and transmitter local-oscillator circuits, supplied in a 16-pin TSSOP package. It operates from a 3.3 V power supply and includes a separate charge-pump supply for extended tuning-voltage range. The device combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, and programmable N divider in one RF clock-and-timing IC. A frequency synthesizer is a phase-locked-loop component that locks an output or tuning signal to a stable reference. In the broader product hierarchy, the ADF4002 is a PLL frequency synthesizer, a clock-and-timing IC, and a semiconductor used to generate or control coherent RF signals. This architecture is useful in wireless upconversion and downconversion paths where stable local oscillators are required by mixers and demodulators. Key features include 400 MHz bandwidth, a 3.3 V supply, programmable charge-pump currents, a 14-bit reference counter, and a three-wire serial programming interface. Analog and digital lock detection provide monitoring options, while hardware and software power-down functions help reduce consumption when the synthesizer is not required. A separate VP charge-pump supply permits greater tuning-voltage headroom than systems using only the main device supply. The internal reference and N counters allow division ratios to be programmed for RF synthesis applications. The serial interface uses CLK, DATA, and LE signals, with 24 bits transferred into the appropriate register when the latch-enable signal is asserted. Designers should treat loop bandwidth, reference jitter, charge-pump current, VCO gain, and divider settings as a coordinated system rather than optimizing one parameter independently. Typical uses include wireless receiver and transmitter local oscillators, frequency conversion in RF front ends, phase and frequency control in communications equipment, and evaluation of PLL loop behavior. In each case, the 400 MHz bandwidth and programmable charge-pump current provide useful flexibility, although the external VCO and passive network determine the final tuning range and phase-noise performance. For a new layout, place the reference, charge-pump, supply, and decoupling connections according to the manufacturer datasheet. Keep the serial programming traces compact, provide adequate return paths, and treat loop-filter component selection as part of the RF design. The manufacturer's evaluation hardware and software provide a practical way to establish register settings before integrating the synthesizer into a production board. This page combines manufacturer specifications, sourcing guidance, comparison points, and practical PLL design considerations. It also identifies where pin-level and lifecycle information should be checked directly in the Analog Devices data sheet, Rev. C, and the current product page before a design reaches production.