Ethernet PHYs
بەرهەمەکان (8)
BCM5461A1KFBG - Single-Port Gigabit Ethernet PHY | Broadcom
Broadcom BCM5461A1KFBG is a single-port Ethernet transceiver with support for 10 Mb/s, 100 Mb/s, and 1 Gb/s data rates, manufactured in a 0.13 μm process and housed in a 100-pin FBGA package. The device belongs to Broadcom's 0.13 μm Gigabit copper PHY family, combining 10/100/1000BASE-T Ethernet interface capability in a surface-mount package designed for compact network equipment. An Ethernet PHY, or physical-layer transceiver, is the component that converts logical data transferred through a media-access controller into signals suitable for a physical network medium and converts received signals back into digital data. Within the network interface hierarchy, a PHY operates beneath the Ethernet MAC and above the physical medium. The BCM5461A1KFBG therefore serves as the physical-layer element in a copper-Ethernet network interface, while MAC, PHY management, magnetics, and system-level routing are handled elsewhere in the design. The BCM5461A1KFBG supports all three principal Ethernet rates of 10 Mb/s, 100 Mb/s, and 1 Gb/s. Its single-transceiver configuration makes it appropriate for one-port routers, switches, industrial gateways, and network interface cards. The 100-pin FBGA package supports compact surface-mount layouts, but its fine pitch requires careful PCB layout, ground-plane continuity, and assembly-process control. Broadcom describes the underlying 0.13 μm process as a cost- and power-oriented implementation for Gigabit copper solutions. As part of Broadcom's 0.13 μm copper-PHY portfolio, the device supports integration with Ethernet magnetics, a MAC, and a host processor. The manufacturer identifies related family members including BCM5404, BCM5414, BCM5421, BCM5421S, BCM5424, BCM5434, BCM5464, and BCM5464S. Selection among those devices should be based on the complete datasheet, including supported rates, electrical characteristics, package drawing, register behavior, and clocking requirements rather than family membership alone. Typical deployments include industrial Ethernet gateways, embedded routers, access equipment, test instruments, and compact single-port network adapters. Its single-port organization avoids allocating resources for unused PHYs, while the 100-pin FBGA package reduces board area compared with larger leaded implementations. Systems requiring multiple physical Ethernet ports will normally need additional PHY devices and corresponding magnetics or coupling components. PCB implementation is the principal engineering consideration. Follow the manufacturer's land pattern, ball assignments, via requirements, and recommended stack-up when laying out the 100-pin FBGA. Place decoupling and clock components close to their associated balls, maintain a continuous ground reference under the device, and follow the prescribed assembly and reflow profile. Because the published excerpt does not reproduce the complete ball map, use the manufacturer pin-description table before assigning signals. This page combines the confirmed device identity, Ethernet rates, process technology, package format, sourcing information, and application analysis with explicit engineering guidance. It also distinguishes directly documented characteristics from parameters that require confirmation in the complete Broadcom datasheet, helping designers plan the PCB and system architecture without assuming unreleased electrical limits.
CS8952-CQ - 10/100 Ethernet PHY | Cirrus Logic | 100-TQFP
The Cirrus Logic CS8952-CQ is a CrystalLAN 10BASE-T and 100BASE-X Ethernet physical-layer transceiver with a 5 V supply, 10 Mb/s and 100 Mb/s operation, and a 100-pin TQFP package measuring 14 mm by 14 mm. It provides a Media Independent Interface for connection to a network Media Access Controller and supports 100BASE-TX copper, 100BASE-FX fiber, and 10BASE-T links. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts parallel controller-facing signals into physical network signals and receives incoming physical-layer signals for delivery to the MAC. The CS8952-CQ belongs to the interface-IC hierarchy, where a PHY sits beneath the Ethernet MAC and above the physical copper or fiber medium. Its MII interface supports both 10 Mb/s and 100 Mb/s designs, while its pseudo-ECL interface is intended for external 100BASE-FX optical modules. The adaptive receive equalizer is optimized for immunity to noise and near-end crosstalk, and the manufacturer describes receiver operation over cable lengths exceeding 160 m under suitable conditions. The device also emphasizes low transmit jitter, with a published feature value below 400 ps. These characteristics make the PHY applicable to network interface cards, Ethernet switches, repeaters, and embedded equipment requiring a parallel MAC interface rather than a modern serial PHY interface. Internally, the CS8952-CQ is a CMOS physical-layer IC combining 10BASE-T and 100BASE-X functions. Its operating modes can be tailored for low-latency 100BASE-TX repeaters, switches, and MII-based network interface cards. Control and status registers provide access to operating characteristics, while the MII handles parallel data transfer and interconnects with compatible 10 Mb/s or 100 Mb/s Media Access Controllers. Typical applications include legacy Ethernet network interface cards, 100BASE-TX switching equipment, 100BASE-FX optical links using external fiber modules, industrial control networking, and legacy embedded Ethernet equipment. For copper designs, magnetic-interface components and a correctly terminated network transformer are required. Fiber implementations also require an external optical transceiver compatible with the CS8952-CQ pseudo-ECL interface. When laying out a CS8952-CQ board, treat the MII, clock, power, and analog network paths as separate high-speed and potentially noisy domains. Place input and output decoupling capacitors close to the device, route the MII clock carefully, and follow the reference layout and component-selection guidance in the manufacturer datasheet. Maintain short return paths and appropriate isolation between the digital controller interface and copper or fiber media interfaces. This product page combines the CS8952-CQ ordering information, package details, electrical coverage, drop-in family options, comparison data, and practical Ethernet interface design guidance. It is intended to help engineers identify whether the legacy MII-based CrystalLAN transceiver remains suitable for a specific 10 Mb/s or 100 Mb/s network design before placing the final order.
DP83847ALQA56A - 10/100 Ethernet PHY | Texas Instruments
The Texas Instruments DP83847ALQA56A is a single-channel 10/100-Mbps Ethernet physical-layer transceiver with integrated PMD sublayers, designed for 10BASE-T and 100BASE-TX Ethernet communication over Category 3 or Category 5 unshielded twisted-pair cables. The device operates from a 3 V to 3.6 V supply, includes 5 V tolerant I/O, and is packaged in a 56-WQFN 9 x 9 mm surface-mount package. An Ethernet PHY is the physical-layer component in an Ethernet communications hierarchy. It converts logical data transmitted by a MAC or network controller into electrical signals for twisted-pair cabling and converts received signals back into digital data. The DP83847 supports the 10 Mb/s and 100 Mb/s Ethernet rates defined for its 10BASE-T and 100BASE-TX modes, while Parallel Detection helps determine the connection type and link status during Auto-Negotiation. The DP83847 uses low-power 0.18 µm CMOS technology and is specified for typical power consumption below 351 mW. Its 5 V tolerant I/O structure allows the digital interface to connect to systems using higher logic levels while the core operates from the 3.3 V supply range. The device includes an external twisted-pair transformer interface, making it suitable for Ethernet PHYs used in industrial, office, home, and embedded networking equipment. The manufacturer documentation identifies the DP83847 as a full-feature single Physical Layer device with integrated PMD sublayers. It supports 10BASE-T and 100BASE-TX protocols, Parallel Detection under IEEE 802.3u, and hardware reset-controlled configuration through latched float and pull-down pins. The electrical design requires careful attention to the external magnetics, line impedance, termination, decoupling, and signal routing on the printed circuit board. Typical applications include industrial Ethernet controllers, embedded Linux systems, factory automation equipment, network interface controllers, print servers, IP cameras, and communications equipment requiring 10/100-Mbps copper Ethernet. A system implementation must provide the required external transformer and suitable RJ45 or cable-side interface while observing the device’s pin configuration and power-supply recommendations. For PCB design, place the PHY, transformer, and supporting passive components according to the manufacturer’s recommended layout, keep high-current and high-speed paths controlled, and provide local supply bypassing close to the power pins. Use the manufacturer datasheet for the definitive pin assignment, package dimensions, timing characteristics, and electrical limits before releasing production hardware. This product page consolidates the manufacturer’s technical description, lifecycle information, package details, application guidance, and verified cross-reference information. It distinguishes the obsolete DP83847ALQA56A from the documented direct substitute DP83847ALQA56A/NOPB while avoiding unsupported assumptions about additional replacement parts.
DP83849IDVS/NOPB - Dual-Port 10/100 Ethernet PHY | Texas Instruments
The Texas Instruments DP83849IDVS/NOPB is an industrial-temperature, dual-port 10/100-Mbps Ethernet PHY transceiver with fiber support, packaged in an 80-pin TQFP (PFC) package measuring 12 x 12 mm. It provides two transmit and two receive channels for copper or fiber-based Ethernet connectivity, operates across -40°C to +85°C, and is designed for embedded networking equipment that requires multiple physical-layer interfaces. An Ethernet PHY transceiver is the physical-layer component that converts digital Ethernet data into electrical or optical signaling and receives incoming signaling for conversion into digital data. Within the network hierarchy, this device belongs to Ethernet transceivers, physical-layer devices, interface ICs, and semiconductor components. It connects an Ethernet MAC or network processor to physical media through integrated drivers, receivers, clocking, and auto-negotiation functions. The DP83849IDVS/NOPB supports 10/100-Mbps operation on two independent ports. Its dual-channel architecture reduces the number of separate PHY devices required in routers, industrial controllers, network switches, and test equipment. Industrial-temperature operation makes it suitable for systems expected to operate across a broad ambient range, while the 80-pin TQFP construction supports conventional surface-mount assembly and multilayer PCB routing. Fiber support extends the design beyond copper cabling and allows optical-network-interface circuitry to be connected to the PHY where appropriate. A complete Ethernet design still requires external magnetics, isolation components, connectors or fiber transceivers, a stable supply, suitable decoupling, and a compliant signal-integrity layout. The PHY does not replace the external passive network components required at the cable or fiber interface. Typical uses include industrial Ethernet gateways, dual-port embedded controllers, network-interface cards, optical network equipment, factory automation controllers, and communications infrastructure. The device can be especially useful where two 10/100 ports are required without allocating two separate PHY packages or where industrial temperature performance is required rather than a consumer-temperature alternative. Design the power, clocks, magnetic components, and medium-dependent interfaces directly from the manufacturer datasheet. Keep the PHY and its support network on a controlled impedance layer, provide the required local bypass capacitors, and maintain the specified clock and reset sequencing. Confirm the complete pin assignment and exposed thermal-pad connection on the official package drawing before fabrication. This product record combines the manufacturer’s device classification, package and temperature information, distributor listing details, and practical Ethernet design guidance. It also distinguishes true package-compatible alternatives from broader functional equivalents so engineers can assess PCB reuse, media support, and operating-temperature requirements before committing to a replacement.
KSZ8041MLL - 10/100 Ethernet PHY | Microchip | MII
The Microchip Technology KSZ8041MLL is a single-port 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a full MII host interface, supplied in a 48-LQFP 7 x 7 mm package. It supports 10 Mb/s and 100 Mb/s Ethernet operation from a single 3.3 V supply. The device interfaces with an Ethernet media-access controller through MII, RMII, or SMII-compatible signaling and provides the physical-layer functions required to connect a digital controller to a 10/100 Ethernet network. An Ethernet PHY is a physical-layer transceiver within the broader Ethernet interface hierarchy. It converts digital frame data from a MAC controller into physical signals suitable for twisted-pair cabling and recovers those signals at the receiving endpoint. The KSZ8041 family combines a mixed-signal PHY implementation with configurable operating modes, reducing board area and power consumption while preserving compatibility with conventional Ethernet controller interfaces. Key features include support for 10BASE-T and 100BASE-TX links, full MII support on the MLL version, a single 3.3 V supply, and an integrated 48-pin LQFP package measuring 7 x 7 mm. The family also supports automatic crossover-related functions identified by Microchip as HP Auto MDI/MDIX. Configuration strapping pins establish speed, duplex, auto-negotiation, power-down behavior, and PHY-address settings when the device starts or resets. The mixed-signal architecture is central to the KSZ8041 implementation. Analog transmit and receive circuitry works with the digital MAC-facing interface, allowing the same PHY family to support copper links at 10 Mb/s or 100 Mb/s. MII provides a parallel data path between the PHY and controller, while the broader KSZ8041 family is documented with RMII and SMII interface support. Designers must still verify the exact interface and strap requirements of the selected ordering code against the manufacturer datasheet. Typical uses include embedded Ethernet ports, industrial controllers, communications equipment, network interface adapters, and systems using a Microchip-compatible 10/100 Ethernet controller. The KSZ8041MLL is especially relevant to designs that require the basic MII-supported PHY in a 48-LQFP surface-mount package rather than the TL or FTL ordering options described as TQFP packaged in the manufacturer data sheet. Layout is critical because the device combines high-speed digital interface signals with sensitive analog receive and transmit circuits. Follow the manufacturer's hardware design checklist, keep the PHY and magnetics interface area tightly controlled, provide the required decoupling, and avoid routing sensitive analog traces beneath digital or high-current paths. Verify magnetics, termination, reset, strap, and crystal or clock requirements before releasing the PCB. This page consolidates the verified distributor description, manufacturer data-sheet identification, package information, hardware-design guidance, and application-oriented engineering considerations. It also distinguishes the basic MII MLL variant from related KSZ8041 ordering codes and identifies where package, electrical, lifecycle, or compliance details require confirmation from the latest Microchip documentation.
KSZ8041MLL-TR - 10/100 Ethernet PHY | Microchip | MII (Tape & Reel)
The Microchip Technology KSZ8041MLL-TR is a single-port 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a full MII host interface, supplied in a 48-LQFP 7 x 7 mm package. It supports 10 Mb/s and 100 Mb/s Ethernet operation from a single 3.3 V supply. The device interfaces with an Ethernet media-access controller through MII, RMII, or SMII-compatible signaling and provides the physical-layer functions required to connect a digital controller to a 10/100 Ethernet network. An Ethernet PHY is a physical-layer transceiver within the broader Ethernet interface hierarchy. It converts digital frame data from a MAC controller into physical signals suitable for twisted-pair cabling and recovers those signals at the receiving endpoint. The KSZ8041 family combines a mixed-signal PHY implementation with configurable operating modes, reducing board area and power consumption while preserving compatibility with conventional Ethernet controller interfaces. Key features include support for 10BASE-T and 100BASE-TX links, full MII support on the MLL version, a single 3.3 V supply, and an integrated 48-pin LQFP package measuring 7 x 7 mm. The family also supports automatic crossover-related functions identified by Microchip as HP Auto MDI/MDIX. Configuration strapping pins establish speed, duplex, auto-negotiation, power-down behavior, and PHY-address settings when the device starts or resets. The mixed-signal architecture is central to the KSZ8041 implementation. Analog transmit and receive circuitry works with the digital MAC-facing interface, allowing the same PHY family to support copper links at 10 Mb/s or 100 Mb/s. MII provides a parallel data path between the PHY and controller, while the broader KSZ8041 family is documented with RMII and SMII interface support. Designers must still verify the exact interface and strap requirements of the selected ordering code against the manufacturer datasheet. Typical uses include embedded Ethernet ports, industrial controllers, communications equipment, network interface adapters, and systems using a Microchip-compatible 10/100 Ethernet controller. The KSZ8041MLL-TR is especially relevant to designs that require the basic MII-supported PHY in a 48-LQFP surface-mount package rather than the TL or FTL ordering options described as TQFP packaged in the manufacturer data sheet. Layout is critical because the device combines high-speed digital interface signals with sensitive analog receive and transmit circuits. Follow the manufacturer's hardware design checklist, keep the PHY and magnetics interface area tightly controlled, provide the required decoupling, and avoid routing sensitive analog traces beneath digital or high-current paths. Verify magnetics, termination, reset, strap, and crystal or clock requirements before releasing the PCB. This page consolidates the verified distributor description, manufacturer data-sheet identification, package information, hardware-design guidance, and application-oriented engineering considerations. It also distinguishes the basic MII MLL variant from related KSZ8041 ordering codes and identifies where package, electrical, lifecycle, or compliance details require confirmation from the latest Microchip documentation.
KSZ8041NL-TR - 10/100 Ethernet PHY, MII/RMII, 32-QFN | Microchip
The Microchip KSZ8041NL-TR is a single-supply 10BASE-T/100BASE-TX physical layer (PHY) transceiver that provides MII and RMII MAC interfaces, housed in a 32-pin QFN (5x5 mm) package with HP Auto-MDIX support. The device operates from a single 3.3V supply (3.135V to 3.465V), supports 10/100 Mbps data rates per IEEE 802.3 and IEEE 802.3u, and integrates the line-side magnetics interface as well as baseline wander correction to extend signaling distance. A PHY (physical layer device) is the lowest tier of the Ethernet OSI stack, sitting just above the transformer/MDI and below the MAC layer. It handles line coding (MLT-3 / 4B5B), link training, auto-negotiation, and clock recovery. Within a typical embedded Ethernet design, a PHY sits between the magnetics plus RJ45 jack and an Ethernet MAC, either inside a microcontroller or as a separate controller; engineers select a discrete PHY when the host MCU/MAC lacks 10/100 support, when isolation or industrial temperature range is required, or when a broader MAC/PHY ecosystem has been validated for a given application. Key features of the KSZ8041NL-TR include 1/1 transceiver configuration with full MII and RMII MAC-side interfaces (SMII supported on the KSZ8041RNL version), HP Auto-MDIX crossover correction that eliminates the need for crossover cables, on-chip 1.8V regulator that can optionally power the MAC, low-power energy-detect mode, and linkMD cable diagnostics for opens, shorts, and cable length estimation. The mixed-signal design reportedly reduces power consumption versus competing 100 Mbps PHYs. Architecturally, the KSZ8041NL uses a DSP-based echo canceller and adaptive equalizer to achieve robust 100BASE-TX performance over CAT-5 cable, with HP Auto-MDIX implemented in the analog front end to autonegotiate polarity and pair roles. The MAC interface supports both MII (25 MHz reference clock at 100 Mbps) and RMII (50 MHz reference clock shared between MAC and PHY), enabling pin-compatible use with a wide range of microcontrollers. Typical applications include set-top boxes and IPTV gateways, network-capable printers and MFPs, industrial Ethernet sensors and PLCs, gaming consoles, and any embedded design that needs a 10/100 Ethernet port without a built-in PHY. The QFN-32 (5x5 mm) small footprint also suits space-constrained consumer and IoT appliances. When laying out this part, give the 50 MHz RMII clock trace a short, matched-length path to both the MAC and the PHY, and follow Microchip's KSZ8041NL Hardware Design Checklist for RJ45 magnetics pairing; do not skip the center-tap capacitor network on each line-side pair. This page compiles distributor pricing, drop-in alternatives, and PCB design notes not found in the bare datasheet, helping engineers select and place the KSZ8041NL-TR quickly.
KSZ8051RNL - 100BASE-TX Ethernet PHY | Microchip | Automotive
Microchip Technology KSZ8051RNL is a single-supply 10BASE-T/100BASE-TX Ethernet physical-layer transceiver for automotive Ethernet designs. It supports the Reduced Media Independent Interface, or RMII, and is supplied in a 32-pin lead-free QFN package measuring 5 mm by 5 mm. The device is AEC-Q100 standard qualified and operates from a 3.3 V supply, making it suitable for automotive body, comfort, and infotainment networks where a compact Ethernet PHY is required. Its integrated physical-layer functions reduce the need for external magnetics and simplify PCB implementation compared with discrete Ethernet interfaces. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts between a digital MAC-facing interface and analog signals carried over twisted-pair Ethernet cabling. The KSZ8051RNL supports 10BASE-T and 100BASE-TX operation through an RMII connection to an Ethernet MAC or switch controller. Because RMII uses a parallel digital interface, it reduces the number of signal lines compared with MII while maintaining compatibility with common automotive Ethernet controller architectures. The 32-QFN package supports compact placement close to the Ethernet magnetics and connector. The KSZ8051RNL includes integrated 10BASE-T on-chip termination resistors, as shown in the manufacturer system-block diagram, and supports management access through MDC and MDIO signals. Its 50 MHz RMII reference-clock arrangement allows the device to accept REF_CLK from the MAC or system board at XI and leaves the corresponding output as no connect. This makes clock planning an important part of RMII interface implementation. The manufacturer identifies the KSZ8051 as a highly integrated PHY intended to reduce board cost and simplify board layout. Typical applications include automotive Ethernet infotainment systems, head units, domain controllers, vehicle gateways, telematics units, and industrial or embedded Ethernet equipment using 100BASE-TX links. The device can support low-power management and connectivity functions where the system requires a 10/100 Ethernet physical layer without a full MII interface. The companion KSZ8051MNL uses the MII interface, so it is not an interchangeable choice for an existing RMII board. For layout, place the PHY near the RJ45 or automotive Ethernet connector and follow the manufacturer reference layout for magnetics, termination, and high-speed differential routing. Use the datasheet pin-description table and layout guidance when assigning signals, and verify the RMII clock source before fabrication. The AEC-Q100 qualification makes the KSZ8051RNL particularly relevant to automotive programs, but system-level qualification, EMC testing, and environmental testing remain the responsibility of the final vehicle or equipment design.