I/O Expanders
بەرهەمەکان (3)
PCA9557PWT - 8-Bit I2C I/O Expander | Texas Instruments
Texas Instruments PCA9557PWT is an 8-bit low-power I/O expander for I2C and SMBus systems, operating from 2.3 V to 5.5 V with a 400 kHz bus interface in a 16-pin TSSOP package. It adds eight remotely controlled input/output ports to a host processor without requiring a dedicated parallel bus. An I/O expander is an interface IC that extends the number of digital input and output lines available to an embedded system. The PCA9557 combines an 8-bit input port register, an 8-bit output port register, reset and configuration registers, and an I2C/SMBus interface. This hierarchy places it within interface ICs, digital logic, and broader semiconductor-based system expansion designs. The PCA9557 supports both input and output operation through its port registers, while the configuration register controls each pin's direction. It is suitable for reading switches and logic states or driving digital inputs. The device also includes a reset function and low-current operation, helping it fit low-power embedded control, industrial automation, consumer electronics, and communication equipment. The I2C interface provides a compact connection between the expander and a host microcontroller or processor. Its 400 kHz bus capability supports straightforward communication rates for control and monitoring systems. Because the device is controlled through registers rather than a parallel data bus, it reduces the number of host pins required for additional digital I/O. Typical uses include configurable input/output modules, LED and relay-control interfaces, keypad and switch sensing, industrial control panels, and auxiliary port expansion for embedded systems. The 2.3 V to 5.5 V operating range also supports both 3.3 V and 5 V system rails. When designing a board around the PCA9557PWT, connect pull-up resistors to the I2C bus and keep the bus routing compact. Confirm the intended direction and reset state of every port bit in firmware, and verify the host's logic levels before using the device across mixed-voltage sections. The TSSOP-16 footprint also requires careful assembly planning because its lead pitch is narrower than a standard SOIC package. This page combines manufacturer specifications, practical application guidance, interface design notes, and drop-in replacement information to help engineers evaluate the PCA9557PWT for compact embedded I/O expansion.
PCAL9714HN/Q900 - 14-bit SPI I/O Expander AEC-Q100 | NXP
The NXP Semiconductors PCAL9714HN/Q900 is a 14-bit ultra low-voltage level-translating SPI I/O expander with Agile I/O features, interrupt output, and reset, qualified to AEC-Q100 for automotive applications and housed in a 24-pin HVQFN (4x4 mm) package. It expands a microcontroller's GPIO count over a Serial Peripheral Interface running up to 5 MHz, with an interface that operates down to 1.1 V. An I/O expander is a peripheral IC that gives a host microcontroller additional general-purpose input/output pins over a serial bus such as SPI or I2C. In the system hierarchy, an I/O expander sits between the microcontroller (the host) and the end loads - switches, LEDs, sensors, or other digital devices - and belongs to the broader family of interface ICs used for remote I/O expansion in embedded systems. Key features include the 14 independently configurable GPIO pins, an ultra low-voltage SPI interface that translates directly from cores operating down to 1.1 V, and NXP's Agile I/O feature set, which provides configurable output drive strength, latch-up-free power-up, and programmable pull-up/pull-down behavior. The dedicated interrupt output (INT) signals the host when an input changes state, and the active reset (RESET) pin restores the register map to default conditions without a power cycle. Technically, the PCAL9714 performs internal level translation between the low-voltage SPI interface side and the wider I/O supply, allowing a 1.1 V to 1.8 V microcontroller to safely drive I/O powered at higher voltages. The SPI clock supports up to 5 MHz, and the HVQFN24 package (4 x 4 x 0.85 mm body, plastic thermal enhanced very thin quad flat, no leads) suits space-constrained automotive and industrial boards. Typical applications include automotive body control modules and door-zone electronics, keypad and switch matrix scanning, LED and indicator control, and fan or sensor status monitoring in industrial controllers. The AEC-Q100 qualification makes it especially appropriate for automotive tiers where reliability over temperature is mandatory. Design consideration: keep the SPI traces short and decouple the VDD pins with 100 nF ceramics close to the package; the ultra low-voltage interface tolerates little noise margin, so signal integrity planning matters more than with 3.3 V parts. This page synthesizes distributor listings, AEC-Q100 qualification details, drop-in family variants, and practical design notes not found in the manufacturer datasheet alone. Pricing shown is as of 2026-10-19 where available.
PCAL9722HN/Q900 - 22-bit SPI I/O Expander AEC-Q100 | NXP
The NXP PCAL9722HN/Q900 is an ultra-low-voltage translating 22-bit SPI I/O expander with Agile I/O features, interrupt output and reset, supplied in a 32-pin HVQFN (5x5 mm) package and qualified to AEC-Q100 for automotive applications. It communicates over a 5 MHz SPI bus and supports a supply voltage range of 1.1 V to 5.5 V on the SPI bus side, enabling bidirectional voltage-level translation and GPIO expansion between 1.1 V and 5.5 V domains. An I/O expander is a peripheral IC that adds general-purpose input/output pins to a microcontroller (MCU) or microprocessor (MPU) over a serial interface, extending pin count without upgrading to a larger device. In the power-management and interface hierarchy, I/O expanders sit in the system I/O subsystem alongside GPIO controllers, port expanders and level translators. The PCAL9722 is unusual in combining both functions: expansion and translation. Key features include 22 configurable GPIO channels, a 5 MHz SPI interface, ultra-low-voltage operation down to 1.1 V for direct connection to advanced low-core-voltage MCUs, Agile I/O functions such as configurable output drive strength and latchable inputs, a dedicated interrupt output, and an external reset input for deterministic power-up states. Technically, the PCAL9722 uses a dual-supply translating architecture: the SPI side operates from 1.1 V to 5.5 V while the I/O side supports a separate port supply, allowing safe interfacing between a 1.2 V core-domain MCU and 3.3 V or 5 V loads. The Agile I/O feature set provides register-level control over pull-up/pull-down, drive strength and input latching, reducing external components. Typical applications include automotive body and zone control modules, sensor and actuator fan-out in AEC-Q100-qualified systems, and industrial I/O modules where an MCU pin budget is exhausted. The Q900 ordering variant targets automotive temperature-grade builds. Design tip: keep the SPI clock at or below 5 MHz and use the reset pin to guarantee defined GPIO states during low-voltage brownouts. This page synthesizes distributor availability, drop-in alternatives, and design guidance not found in the manufacturer datasheet.