بەرهەمەکان (46,000+)

AD7451ART-R2 - 12-Bit 1 MSPS Pseudo-Diff SAR ADC | Analog Devices | SOT-23-8
AD7451ART-R2

AD7451ART-R2 - 12-Bit 1 MSPS Pseudo-Diff SAR ADC | Analog Devices | SOT-23-8

The Analog Devices AD7451ART-R2 is a 12-bit, 1 MSPS successive-approximation analog-to-digital converter (ADC) in an 8-lead SOT-23 package with a pseudo-differential analog input. Specified for VDD from 2.7 V to 5.25 V, it consumes 4 mW maximum at 1 MSPS with VDD = 3 V and 9.25 mW maximum at 1 MSPS with VDD = 5 V. The serial interface is compatible with DSP, MICROWIRE, QSPI, and SPI. Analog Devices positions the part as a low-power, high-speed SAR ADC for space-constrained single-channel data acquisition. A SAR (successive-approximation-register) ADC is one of the two dominant architectures for medium-speed, medium-resolution data conversion. Unlike delta-sigma ADCs that oversample and integrate over many clock cycles, a SAR ADC performs a binary search across an internal capacitive DAC in a single conversion cycle, producing a latency of one clock period. The result is predictable, alias-free behavior at Nyquist, deterministic settling, and very low pipeline delay, which makes SAR ADCs the preferred choice for multiplexed multi-channel systems, motor control feedback loops, and instrumentation front-ends. Key differentiating features of the AD7451ART-R2 include a 70 dB SINAD rating at a 100 kHz analog input frequency, a wide-bandwidth low-noise differential track-and-hold front-end that handles input signals above 1 MHz, and a programmable flexible power/serial-interface management. The external VREF input accepts 100 mV to 3.5 V (or up to VDD), giving designers fine control over the input full-scale range. An overbar CS (active-low chip select) and serial clock control the conversion and data acquisition, supporting direct connection to microprocessors and DSPs without glue logic. Architecturally, the device pairs a low-noise wide-bandwidth differential T/H amplifier with a charge-redistribution SAR core and an on-chip conversion clock. The pseudo-differential input means IN+ is sampled against GND with IN- providing only common-mode rejection, simplifying front-end drive versus a fully-differential topology. External reference decoupling is critical to realizing the datasheet SINAD figure. Typical applications include industrial process control loop monitoring, portable battery-powered instrumentation, optical-module photodiode current sensing (with external TIA), and general-purpose data acquisition in PLC analog input modules. Designers should note that achieving the 70 dB SINAD figure requires a clean, well-bypassed external reference and a low-impedance analog input driver; small SOT-23-8 thermal limits also constrain continuous duty cycle at full 1 MSPS. This page synthesizes distributor pricing, drop-in alternatives, and practical design guidance not found in any single manufacturer datasheet.

RFQ پەیوەندی
AD7451BRT-R2 - 12-Bit 1MSPS Pseudo-Diff SAR ADC | ADI
AD7451BRT-R2

AD7451BRT-R2 - 12-Bit 1MSPS Pseudo-Diff SAR ADC | ADI

The Analog Devices AD7451BRT-R2 is a 12-bit, 1 MSPS successive-approximation (SAR) analog-to-digital converter with a pseudo-differential analog input, packaged in an 8-pin SOT-23 (RT) on a 7-inch tape-and-reel. It operates from a single 2.7 V to 5.25 V supply, draws 4 mW at 1 MSPS with VDD of 3 V, and integrates a low-noise, wide-bandwidth track-and-hold that does not require an external buffer. A successive-approximation ADC (SAR ADC) is a type of Nyquist-rate converter that uses an internal binary-search capacitor array to resolve one bit per clock cycle, producing deterministic latency, no pipeline delay, and excellent DC accuracy. SAR ADCs sit beneath the broader ADC hierarchy (SAR > Nyquist-rate > data converter > mixed-signal IC > semiconductor) and are favored when applications need simultaneous high accuracy, low latency, and small package size. The AD7451 family extends that architecture into an ultra-miniature 8-pin SOT-23, making it the smallest true 12-bit 1 MSPS ADC in ADI's catalog at release. Key specifications include 12-bit resolution, 1 MSPS throughput, pseudo-differential input (IN+ and IN- with IN- usable as ground sense), 4 mW power dissipation at 1 MSPS with VDD = 3 V (9.25 mW with VDD = 5 V), SPI/QSPI/MICROWIRE/DSP-compatible serial interface, and an operating temperature range suitable for industrial environments. The pseudo-differential topology rejects small common-mode noise and supports rail-to-rail single-ended sources with proper reference design. Typical applications include precision industrial process control, portable and battery-powered instrumentation, optical sensor front-ends (photodiode/phototransistor read-out), data acquisition boards, motor control current sensing, and medical patient-monitoring front-ends. The SOT-23-8 footprint is particularly attractive for space-constrained PCB designs where a 12-bit accurate signal chain must fit alongside dense digital logic. When designing with this part, place a 100 nF decoupling capacitor within 2 mm of the VDD pin and a 10 µF bulk capacitor on the supply trace; the reference input (REF) requires a low-impedance 2.5 V reference such as the ADR01 or ADR02 for full 12-bit performance. The -R2 tape-and-reel suffix designates packaging only and does not affect electrical behavior. This page synthesizes cross-reference alternatives, distributor pricing, application guidance, and practical PCB notes that go beyond what the bare datasheet reveals.

RFQ پەیوەندی
AD7452BRT-R2 - 12-Bit 555kSPS SAR ADC | Analog Devices | SOT-23-8
AD7452BRT-R2

AD7452BRT-R2 - 12-Bit 555kSPS SAR ADC | Analog Devices | SOT-23-8

The Analog Devices AD7452BRT-R2 is a 12-bit, high-speed, low-power successive-approximation (SAR) analog-to-digital converter featuring a fully differential analog input, packaged in an 8-pin SOT-23 and offered on a 2,500-piece reel. It operates from a single 3V or 5V power supply and achieves throughput rates up to 555 kSPS while consuming only 1.2 mW of power at 3V and 555 kSPS, making it well suited to battery-powered and portable data-acquisition systems. An SAR ADC is a successive-approximation analog-to-digital converter that uses a binary-search algorithm against an internal DAC to digitize an analog input in N clock cycles (where N is the resolution in bits). Within the converter hierarchy, the AD7452 sits as: ADC -> data converter -> data acquisition IC -> signal-chain component. SAR converters are valued for deterministic latency, single-shot accuracy and DC-friendly behavior - ideal when a precise snapshot, not a continuous waveform stream, is required. Key features of the AD7452BRT-R2 include 12-bit resolution with no missing codes, a fully differential analog input that supports rail-to-rail common-mode swing, an internal 2.5V reference (or option to overdrive with an external reference), a high-speed serial (SPI/QSPI/MICROWIRE/DSP-compatible) interface, and a hardware power-down pin that drops supply current to sub-microamp levels for battery conservation. The architecture combines a low-noise, low-power comparator with a precision switched-capacitor DAC and an internal oscillator, eliminating the need for an external clock. The result is a compact solution that delivers strong AC (THD, SNR) and DC (DNL, INL) performance while keeping the external BOM to the analog front end, reference bypass capacitors and decoupling only. Typical applications include portable instrumentation, sensor signal conditioning (pressure, temperature, strain gauge bridges), data acquisition boards, and battery-powered transducers. The 555 kSPS throughput is sufficient for industrial process-control loops, instrumentation-grade weigh scales and many audio-bandwidth measurement tasks. One practical design consideration: at 5V supply, power dissipation rises with sample rate; route an analog ground return around the input pins and use a 0.1uF ceramic bypass cap adjacent to AVDD to maintain the rated SNR. Choosing between AD7452BRT (legacy packaging) and AD7452BRTZ-R2 depends on whether the design needs the original SOT-23-8 marking or the Z-suffix lead-free SOT-23-8 variant. This page consolidates distributor pricing, parametric comparison vs SAR alternatives and practical design notes not found in the manufacturer datasheet alone, including drop-in and pin-compatible cross-brand considerations for both new designs and legacy 8-pin SOT-23 SAR ADC sockets.

RFQ پەیوەندی
AD745AQ - 20MHz Low-Noise FET Op Amp | Analog Devices
AD745AQ

AD745AQ - 20MHz Low-Noise FET Op Amp | Analog Devices

The Analog Devices AD745AQ is an ultralow-noise, high-speed, JFET-input operational amplifier with a 20 MHz gain-bandwidth product, 12.5 V/us slew rate, and 1 mV maximum offset voltage in an 8-pin CERDIP package. It combines the low voltage noise traditionally associated with bipolar input amplifiers with the very low input bias current of FET-input devices, making it suitable for precision signal-chain applications. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify small differential signals. Its hierarchy extends from amplifier ICs to analog integrated circuits and semiconductor devices. The AD745AQ uses a JFET input stage to provide low input bias current, while its high bandwidth and slew rate preserve signal fidelity across audio, instrumentation, and control systems. Key electrical characteristics include a 20 MHz gain-bandwidth product, 12.5 V/us slew rate, 90 dB open-loop gain, 250 pA maximum input bias current, and 90 uV/°C input voltage offset temperature drift. The manufacturer lists the AD745 family as not recommended for new designs, making legacy maintenance and previously qualified designs the primary use cases. A ceramic CERDIP package supports operation in demanding temperature environments. The AD745 combines low-noise JFET inputs with high-speed closed-loop performance. Its input bias current remains suitable for high-impedance sources, while the 20 MHz bandwidth supports wider signal bandwidth than precision-only amplifiers. The 12.5 V/us slew rate helps preserve large-signal accuracy when configured as a non-inverting or inverting amplifier with suitable feedback and compensation. Typical uses include low-noise audio preamplification, laboratory instrumentation, sensor signal conditioning, photodiode amplification, and precision feedback networks in industrial control equipment. The low 250 pA maximum bias current is particularly useful when source impedance is high, while the 90 dB open-loop gain supports accurate closed-loop amplification when the feedback network is properly selected. Designers should verify the required supply voltage, unity-gain stability, noise-gain bandwidth, output swing, and load capability against the manufacturer datasheet. Because the AD745AQ is a legacy device, engineers should also confirm availability and source the exact ceramic-package ordering code when maintaining an existing qualified assembly. This product page combines the AD745AQ operating characteristics, ordering information, package details, comparison guidance, and practical design notes to support legacy-system maintenance. It also explains where to obtain the manufacturer datasheet and how to evaluate exact MPN substitutions before making a board-level change.

RFQ پەیوەندی
AD745JR-16 - 20MHz Low-Noise FET Op Amp | Analog Devices
AD745JR-16

AD745JR-16 - 20MHz Low-Noise FET Op Amp | Analog Devices

The Analog Devices AD745JR-16 is an ultralow-noise, high-speed JFET-input operational amplifier with a 20 MHz gain-bandwidth product, 12.5 V/µs slew rate, and operation from ±4.8 V to ±18 V, housed in a 16-pin SOIC package. It combines the low voltage noise associated with bipolar-input amplifiers with the very low bias currents of a FET-input device. A JFET-input operational amplifier is an analog signal-conditioning IC whose input stage uses junction field-effect transistors. Within the broader hierarchy of amplifier ICs, it belongs to the precision-amplifier family and provides high input impedance, low distortion, and wide bandwidth for signals that require both noise performance and speed. This makes the AD745 suitable where a conventional CMOS amplifier may lack sufficient input impedance or a slower bipolar device may add excessive noise. The AD745 is designed for precision signal acquisition, instrumentation, audio, and sensor-interface applications. Its 20 MHz gain-bandwidth product supports useful closed-loop bandwidth well beyond audio frequencies, while the 12.5 V/µs slew rate improves large-signal response. The manufacturer describes the device as an ultralow-noise, high-speed, FET-input amplifier, and the 16-pin SOIC option is available in industrial and military temperature grades depending on the order code. The AD745J grade is specified for the industrial temperature range of -40°C to +85°C. Its input stage provides the low input current expected from a FET design while preserving the low voltage-noise behavior normally associated with bipolar input amplifiers. The AD745 family is available in several packages, including 8-pin plastic mini-DIP, 8-pin cerdip, 16-pin SOIC, and chip form, allowing selection according to assembly method and thermal requirements. Typical uses include low-level sensor amplification, precision current measurement, audio and instrumentation signal chains, photodiode interfaces, and high-impedance buffer stages. In these applications, the combination of low noise, low input bias current, and 20 MHz bandwidth allows the amplifier to condition signals without imposing a severe bandwidth or loading penalty on the source. For stable operation, follow the manufacturer's recommended input and output network, provide adequate supply bypassing close to the device, and verify output swing, input common-mode range, and stability across the intended gain and load conditions. The JR-16 order code identifies the 16-pin SOIC package; exact pin functions, noise density, input bias current, and offset limits should be confirmed in the AD745 datasheet before finalizing a design.

RFQ پەیوەندی
AD745KR-16 - 20MHz Low-Noise J-FET Op Amp | Analog Devices
AD745KR-16

AD745KR-16 - 20MHz Low-Noise J-FET Op Amp | Analog Devices

The Analog Devices AD745KR-16 is a single, low-noise, high-speed J-FET input operational amplifier with 20 MHz gain-bandwidth product, 12.5 V/µs slew rate, and low voltage noise in a 16-lead SOIC package. Its J-FET input stage combines the very low input bias current associated with FET transistors with the low voltage noise and high speed normally associated with bipolar input amplifiers. An operational amplifier is an analog signal-processing building block that amplifies the voltage difference between its inverting and non-inverting inputs. The AD745 belongs to the precision-amplifier hierarchy, where accurate amplification, low noise, and high bandwidth are more important than saturated-output or high-output-current performance. Its low-noise J-FET input stage makes the device suitable for instrumentation, sensor interfaces, and precision signal-conditioning circuits. The AD745's headline characteristics include a 20 MHz gain-bandwidth product, a 12.5 V/µs slew rate, and ultralow voltage-noise performance. The 20 MHz bandwidth allows the amplifier to process signals well above the audio range, while the 12.5 V/µs slew rate supports accurate reproduction of large, fast transitions. Because it is a J-FET-input amplifier, the device also offers very low input bias currents, which helps minimize distortion when driven by high-impedance sources. The AD745 can operate on dual supplies or as a single-supply amplifier when the input and output common-mode ranges permit. Design work should verify the supply voltage, input common-mode range, output swing, stability, and noise specifications against the operating conditions in the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and feedback resistors should be selected to preserve the intended closed-loop bandwidth. Typical uses include precision current-to-voltage conversion, low-level sensor amplification, photodiode and phototransistor interfaces, audio and communication-signal conditioning, laboratory measurement front ends, and high-impedance buffer stages. The combination of 20 MHz bandwidth, 12.5 V/µs slew rate, and low-noise J-FET inputs is particularly useful when the source impedance is high enough that input bias current would otherwise create unacceptable offset errors. A key design consideration is that the AD745 is optimized for low-noise, high-speed signal work rather than rail-to-rail input and output operation. Check headroom at both ends of the signal range and account for bias-current-generated error across the source impedance. Feedback-component values and source impedances should also be checked against the amplifier's stability requirements. This page organizes the AD745KR-16 electrical characteristics, package details, application guidance, same-footprint amplifier alternatives, and design notes in one place. It also identifies which published parameters need confirmation in the manufacturer datasheet, helping engineers move from part selection to a validated analog design.

RFQ پەیوەندی
AD745SQ - 20 MHz Ultra-Low-Noise JFET Op Amp | ADI
AD745SQ

AD745SQ - 20 MHz Ultra-Low-Noise JFET Op Amp | ADI

Analog Devices AD745SQ is an ultralow-noise, high-speed, JFET-input operational amplifier with a 20 MHz gain-bandwidth product and a 12.5 V/µs slew rate, housed in an 8-pin CERDIP through-hole package. The device combines the low voltage noise associated with bipolar input amplifiers with the very low input bias current characteristic of a field-effect transistor input stage. Its one-amplifier configuration supports precision signal conditioning, instrumentation, and high-impedance analog front ends. A JFET-input operational amplifier is a voltage-feedback amplifier whose input stage uses junction field-effect transistors. Within the semiconductor hierarchy, it belongs to the operational-amplifier, analog-amplifier, and integrated-amplifier categories. This input architecture is particularly useful when measuring or amplifying signals from high-impedance sensors because it can combine high input impedance, low bias current, low input noise, and wide signal bandwidth in a single monolithic circuit. The AD745 family is identified for its ultralow-noise, high-speed operation. The published 20 MHz gain-bandwidth figure supports closed-loop bandwidth beyond the 10 V/µs range with suitable feedback networks, while the 12.5 V/µs slew rate allows large-amplitude signals to be reproduced with relatively low distortion. Its operating supply current is 8 mA, and the specified temperature range extends from -55°C to 125°C. Exact voltage-noise, input-bias-current, input-offset-voltage, and supply-voltage limits should be taken from the AD745 manufacturer datasheet for the selected temperature and supply conditions. BiFET input stages provide a practical compromise between bipolar and CMOS input amplifiers. Bipolar inputs commonly offer low voltage noise, while FET inputs minimize input bias current and simplify the drive of high-source-impedance transducers. The AD745SQ uses this architecture for applications requiring both bandwidth and low-noise signal handling. Its voltage-noise and common-mode performance remain sensitive to circuit configuration, so resistor values, source impedance, and feedback topology must be evaluated together rather than as isolated specifications. Typical uses include low-level transducer amplification, audio and instrumentation signal chains, laboratory measurement systems, and precision analog filters. The 8-pin CERDIP package also makes the AD745SQ suitable for legacy industrial and scientific equipment that uses through-hole op-amp footprints. Because Analog Devices marks the AD745 family as not recommended for new designs, engineers should verify long-term availability and consider a currently recommended amplifier for new production programs. For a new PCB, do not substitute a surface-mount amplifier without confirming that its electrical performance, supply requirements, pin function, stability behavior, and thermal characteristics satisfy the original design. For an existing 8-pin CERDIP board, preserve adequate supply decoupling, route the feedback loop for minimum parasitic capacitance, and avoid using a long input trace next to high-current switching nodes. These practices help preserve the intended bandwidth and noise performance. This product page combines the AD745 family specifications, lifecycle information, package details, sourcing guidance, and design-focused guidance for the AD745SQ. It also distinguishes true same-package alternatives from broader functional equivalents, helping engineers make a drop-in decision without confusing electrical similarity with PCB compatibility.

RFQ پەیوەندی
AD7466BRM - 12-Bit 200 kSPS Micro-Power ADC | Analog Devices
AD7466BRM

AD7466BRM - 12-Bit 200 kSPS Micro-Power ADC | Analog Devices

The Analog Devices AD7466BRM is a 12-bit successive-approximation analog-to-digital converter designed for low-power, high-speed signal acquisition. It operates from a single 1.6 V to 3.6 V supply, supports throughput rates up to 200 kSPS, and is packaged in an 8-MSOP package. The converter uses a low-noise, wide-bandwidth track-and-hold amplifier to handle input signals with frequencies in excess of 100 kHz. An ADC is an analog-to-digital converter, a semiconductor device that converts a continuously varying analog voltage into a numeric code for processing, measurement, or control. The AD7466 belongs to the successive-approximation ADC family, within the broader ADC and data-converter IC hierarchy. This architecture is useful when moderate resolution, compact size, low power consumption, and serial data transfer are more important than very high conversion rates. The AD7466BRM provides a 12-bit conversion resolution, a single analog input channel, and serial-interface operation identified in the product documentation as MICROWIRE, QSPI, and SPI compatible. Its single-supply operating range allows operation in compact battery-powered and embedded systems where a 1.8 V or 2.5 V rail is available. The low-power architecture helps reduce energy consumption during periodic sampling and standby operation. The AD7466, AD7467, and AD7468 form a related family of 12-bit, 10-bit, and 8-bit high-speed, low-power successive-approximation converters. The AD7466 is therefore useful when the system requires greater resolution than the lower-resolution family members while retaining the same general serial-converter architecture. The wide-bandwidth track-and-hold amplifier supports acquisition of higher-frequency input signals than a slow low-pass-oriented converter would allow. Typical applications include industrial process monitoring, portable instrumentation, sensor interfaces, battery-powered measurement systems, and embedded data acquisition. In a sensor interface, the ADC can digitize a conditioned analog output from a transducer or signal-conditioning front end. In an industrial system, its serial interface can connect to a microcontroller or digital signal processor while its low operating voltage helps reduce system power requirements. Designers should pay attention to input range, reference voltage, sampling timing, digital-interface levels, and the acquisition time required by the source impedance. The input network should present a stable settling waveform during the track phase, and the serial clock and data lines should be configured to match the host controller. Use the manufacturer datasheet and pin-description table when assigning PCB tracks, and review the operating limits for the exact suffix before applying the part in a production design.

RFQ پەیوەندی
AD7466BRT-R2 - 12-Bit 200kSPS Micropower ADC | Analog Devices
AD7466BRT-R2

AD7466BRT-R2 - 12-Bit 200kSPS Micropower ADC | Analog Devices

The Analog Devices AD7466BRT-R2 is a 12-bit, high-speed, low-power successive approximation register (SAR) analog-to-digital converter (ADC) in a 6-pin SOT-23 (RT) package. It operates from a single 1.6 V to 3.6 V power supply and supports throughput rates up to 200 kSPS, drawing only 0.62 mW typical at 100 kSPS with a 3 V supply. The internal reference is taken from VDD, allowing the widest dynamic input range with an analog input span of 0 V to VDD. What is a SAR ADC? A successive approximation register analog-to-digital converter is a precision data conversion IC that uses a binary search algorithm to resolve an analog input voltage into a digital code, one bit per clock cycle. SAR ADCs sit within the broader hierarchy: data-converter -> ADC -> precision converter -> signal chain IC. They are valued for high accuracy at moderate sample rates, low latency, deterministic conversion time, and very low power consumption, making them the workhorse of battery-powered and instrumentation applications. Key features include a flexible serial interface compatible with DSP, MICROWIRE, QSPI, and SPI host controllers; an automatic power-down mode between conversions that drops quiescent current to under 1 microampere; and a wide 1.6 V to 3.6 V single-supply range. The SOT-23-6 footprint makes AD7466BRT-R2 one of the smallest precision 12-bit ADCs available, ideal for space-constrained designs. No external reference is required, simplifying BOM cost. Technically, the AD7466BRT-R2 uses a switched-capacitor charge redistribution architecture with input sampling on the falling edge of CS and conversion driven by the external SCLK. The reference is internally tied to VDD, which trades absolute accuracy for simplicity and minimum external parts. Signal-to-noise-plus-distortion ratio (SINAD) tracks VDD, and integral nonlinearity (INL) and differential nonlinearity (DNL) are specified for industrial temperature grades. Typical applications include portable and battery-powered measurement systems, medical instrumentation front-ends, remote and isolated data acquisition modules, optical sensor monitoring, and low-power industrial sensor interfaces. The part is widely used wherever a 12-bit conversion is sufficient and board area is critical. A key design tip: the SCLK idle state must be set high to match the AD7466 logic convention, and the CS falling edge initiates both sampling and conversion - there is no separate sample/hold control. Bypass VDD with a 1 microfarad plus 100 nanofarad capacitor pair placed within 3 mm of the supply pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single decision-ready reference for the AD7466BRT-R2.

RFQ پەیوەندی
AD7467BRM - 10-Bit 200 kSPS ADC | Analog Devices
AD7467BRM

AD7467BRM - 10-Bit 200 kSPS ADC | Analog Devices

Analog Devices AD7467BRM is a 10-bit, single-channel, successive-approximation analog-to-digital converter with a throughput rate up to 200 kSPS, a 1.6 V to 3.6 V supply range, and an 8-MSOP package. It combines low-power operation with a compact footprint for applications that require moderate resolution and fast sampling. An ADC is an interface IC that converts an analog voltage into a digital code. A successive-approximation ADC performs conversion by progressively comparing the input with a reference voltage. Within the broader semiconductor hierarchy, the AD7467BRM is an ADC, an interface IC, and a data-acquisition component. It is suited to sensors, industrial controls, instrumentation, and embedded systems that need continuous conversion rather than the very high throughput of a flash converter. The principal specifications include 10-bit resolution, one analog input channel, operation from 1.6 V to 3.6 V, and throughput up to 200 kSPS. These characteristics place the device between low-resolution sensor interfaces and higher-resolution precision converters. The single 8-MSOP package also reduces board area compared with larger multi-channel converter packages, while the 1.6 V minimum supply supports compact low-voltage systems. The AD7467 uses a successive-approximation conversion architecture. This architecture is appropriate when moderate conversion speed and low power consumption are more important than very high sampling rates. Analog Devices identifies the AD7466, AD7467, and AD7468 as related 12-bit, 10-bit, and 8-bit converters, respectively, allowing designers to select the resolution that matches the measurement requirement rather than using unnecessary conversion capacity. Typical uses include battery-powered environmental sensors, temperature and pressure measurement front ends, analog control monitoring, portable instrumentation, and industrial data-acquisition modules. The 200 kSPS throughput allows the converter to sample rapidly varying analog signals, while the 10-bit code provides 1,024 quantization levels for general-purpose measurement and control. The main design consideration is matching the input range, reference voltage, sampling network, and digital interface to the source signal. The analog input must remain within the converter's permitted operating range, and source impedance can affect acquisition time. PCB layout should keep analog and digital return paths controlled and place input, reference, and supply bypass components close to their associated pins. This page combines the manufacturer's family-level specifications with package, application, replacement, and design guidance. It also identifies same-footprint resolution alternatives so engineers can assess whether AD7466BRM or AD7468BRM offers a more appropriate conversion resolution without changing the PCB footprint.

RFQ پەیوەندی
AD7468BRT-R2 - 8-Bit 200kSPS Micro-Power ADC | Analog Devices
AD7468BRT-R2

AD7468BRT-R2 - 8-Bit 200kSPS Micro-Power ADC | Analog Devices

The Analog Devices AD7468BRT-R2 is an 8-bit, high-speed, low-power, successive-approximation analog-to-digital converter (SAR ADC) in a 6-pin SOT-23 package, operating from a single 1.6 V to 3.6 V supply and supporting throughput rates up to 200 kSPS. The R2 suffix indicates a 2,500-piece tape-and-reel packaging variant for high-volume manufacturing. A successive-approximation ADC is a type of data converter that converts an analog input voltage into a digital code by performing a binary search across an internal precision DAC, comparing the reconstructed voltage to the input on each clock cycle. The SAR architecture is prized for low power, deterministic latency, and excellent DC accuracy - it occupies the architectural middle ground between flash ADCs (fast but expensive) and integrating/delta-sigma ADCs (precise but slower). It belongs to the broader hierarchy: ADC -> data converter -> signal chain IC -> semiconductor. Key features of the AD7468BRT-R2 include 8-bit resolution, 200 kSPS throughput, 1.6 V to 3.6 V single-supply operation, and an extremely low power dissipation of 0.62 mW typical at 100 kSPS with a 3 V supply (0.12 mW at 100 kSPS / 1.6 V). The device includes a high-speed SPI-/QSPI-/MICROWIRE-/DSP-compatible serial interface, pseudo-differential analog input, and built-in power-down control via the CS bar pin, which reduces current draw between conversions and makes the part ideal for battery-powered systems. The AD7468BRT-R2 uses a charge-redistribution SAR core with an input bandwidth that comfortably exceeds the Nyquist requirement for 8-bit conversion at 200 kSPS, eliminating the need for an external input buffer in many applications. The wide supply range allows direct interfacing with low-voltage microcontrollers, 1.8 V DSPs, and modern battery chemistries (Li-Ion, coin-cell, energy-harvested rails). Typical applications include battery-powered monitoring systems, portable medical instruments (pulse oximeters, glucose meters), remote data acquisition nodes, isolated data acquisition front-ends, and transducer/sensor signal digitisation. The 6-pin SOT-23 footprint is among the smallest ADC packages available, making the part attractive for space-constrained PCB designs. When designing with this device, observe the analog input bandwidth specification - the -3 dB input bandwidth is typically 2 MHz, so excessive input source impedance can introduce gain error. Use the power-down feature between bursts of conversions to extend battery life by an order of magnitude. This page synthesises distributor pricing, parametric drop-in alternatives, and PCB layout notes for engineers who need to specify or second-source the AD7468BRT-R2 in compact, low-power designs.

RFQ پەیوەندی
AD746AQ - 13MHz Dual Precision BiFET Op Amp | Analog Devices
AD746AQ

AD746AQ - 13MHz Dual Precision BiFET Op Amp | Analog Devices

Analog Devices AD746AQ is a dual precision BiFET operational amplifier with 13 MHz gain-bandwidth, 500 ns settling to 0.01% for a 10 V step, and 0.0001% total harmonic distortion. The device is supplied in an 8-pin ceramic dual in-line package for applications requiring low-noise amplification, precision signal conditioning, and fast settling. A BiFET operational amplifier is a voltage-feedback amplifier whose input stage uses junction field-effect transistors. This input structure provides low input bias current and high input impedance while preserving the low offset voltage and common-mode characteristics needed for precision analog systems. In the broader hierarchy, the AD746 belongs to the operational amplifier, analog signal-conditioning IC, and power management and signal-chain semiconductor categories. The AD746AQ contains two AD744 BiFET amplifiers on one monolithic die. Both channels therefore have closely matched DC and AC characteristics. Its 13 MHz gain-bandwidth supports signal bandwidth beyond the 0.01% settling criterion, while the internal compensation provides stable operation at gains of two or greater. A 500 ns settling time is especially useful when amplifying the outputs of 12-bit or 14-bit DACs and ADCs. The low-noise input stage and 0.0001% THD make the amplifier suitable for demanding audio paths, instrumentation channels, and precision buffers. The matched channels can also implement differential, active-filter, line-driver, and current-to-voltage converter circuits. Inputs can operate around the supply rails when configured for the appropriate common-mode range, making the device useful in bipolar ±5 V, ±12 V, and ±15 V systems. Typical uses include ADC input conditioning, DAC output buffering, active low-pass filters, audio preamplification, sensor signal amplification, and precision waveform-generation circuits. In a 12-bit DAC buffer, the AD746AQ combines sufficient bandwidth with fast settling to reduce code-transition error without relying on a complex external compensation network. When laying out an AD746AQ circuit, keep the feedback components and signal traces short, provide adequate supply bypassing close to the device, and use clean ground returns. The ceramic package is suited to legacy precision and industrial equipment, but board availability and thermal performance should be checked before committing to a new design. This page combines manufacturer performance characteristics with application-focused design guidance, package information, comparison data, and practical replacement considerations. It is intended to help engineers determine whether the AD746AQ’s precision, settling behavior, and low-noise BiFET architecture fit a specific analog signal chain.

RFQ پەیوەندی
AD746JN - Dual 500ns Precision BiFET Op Amp | Analog Devices
AD746JN

AD746JN - Dual 500ns Precision BiFET Op Amp | Analog Devices

The Analog Devices AD746JN is a dual precision BiFET operational amplifier with two AD744 amplifier circuits on one monolithic die, 500 ns settling to 0.01%, and an 8-pin PDIP package. Its headline characteristics include an 80 dB open-loop gain, 110 pA input bias current, 0.00035 uA input offset current, and a 75 V/us slew rate. The device operates from 9 V to 36 V total supply, equivalent to +4.5 V to +18 V for single-supply operation or ±4.5 V to ±18 V for dual-supply operation. A BiFET operational amplifier is a voltage-amplifier built around junction field-effect transistor input devices. These low-noise inputs provide high input impedance, low bias current, and low offset current, placing the amplifier within the operational-amplifier hierarchy of signal-conditioning ICs used for precision analog measurement, buffering, filtering, and audio signal paths. The AD746 combines that low-input-current architecture with closely matched amplifier characteristics on the same die. The AD746JN provides fast single-pole settling to within 0.01% in 500 ns, making it useful where acquisition systems require rapid recovery after a large input transition. Its stated total harmonic distortion of 0.0001% supports demanding audio applications, while the monolithic dual-amplifier construction gives closely matched AC and DC characteristics. The 110 pA bias current is particularly useful with high-impedance sensors, and the 80 dB open-loop gain supports precision closed-loop gain configurations. The dual amplifier can implement two independent signal-conditioning channels or can be configured as a differential amplifier when its two amplifiers are interconnected appropriately. The device supports instrumentation and precision signal-chain requirements where low input current, high open-loop gain, fast settling, and low distortion are important. Its operating supply range also accommodates conventional ±15 V laboratory and industrial analog systems as well as lower-voltage designs operating from a single +9 V to +36 V rail. Typical uses include input buffering for 12-bit and 14-bit ADCs or DACs, precision measurement front ends, audio signal conditioning, sample-and-hold signal paths, and active filters. A dual package reduces board area when two amplifier channels are required. It is particularly appropriate when the signal source has high source impedance, because the 110 pA bias current limits the voltage error introduced across that source resistance. Designers should follow the manufacturer datasheet for pin connections, supply bypass capacitors, input and output voltage limits, and common-mode range. Decoupling should place a suitable ceramic capacitor close to the positive and negative supply pins, while input routing should minimize leakage and stray capacitance. Because a dual amplifier shares a package, thermal performance and channel-to-channel matching should be considered before assigning each channel to different thermal or source-impedance conditions. This product page combines the AD746JN electrical characteristics, package details, practical application guidance, and verified drop-in replacement information in one engineering-focused reference. It also highlights where the JFET-input architecture, settling performance, low distortion, and dual-channel construction make AD746JN a strong choice for precision buffering and instrumentation.

RFQ پەیوەندی
AD746JR - Dual 13MHz Precision BiFET Op Amp | Analog Devices
AD746JR

AD746JR - Dual 13MHz Precision BiFET Op Amp | Analog Devices

The Analog Devices AD746JR is a dual precision BiFET operational amplifier in an 8-pin SOIC package, combining two AD744 amplifier circuits on one monolithic die. Its headline specifications are 13 MHz gain-bandwidth product, 75 V/µs slew rate, and ±4.5 V to ±18 V supply operation. Both channels benefit from close AC and DC matching because they share the same die and operating environment. An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain and negative feedback to amplify weak differential signals with high input impedance and low output impedance. Within the amplifier hierarchy, the AD746JR is a voltage-feedback BiFET precision amplifier: a BiFET input stage, dual-channel architecture, and monolithic construction distinguish it from general-purpose CMOS amplifiers and comparators. This combination makes it suitable for instrumentation, filtering, and precision conversion interfaces. The AD746 datasheet identifies a single-pole response that settles to 0.01% in 500 ns. It also specifies a very low total harmonic distortion of 0.0001%. These characteristics support fast-settling buffer stages for 12-bit and 14-bit DACs and ADCs. The dual architecture also allows one channel to buffer a reference while the other performs amplification, although simultaneous precision performance remains tied to matching load impedances and balanced layout. Mechanically, the AD746JR uses an 8-pin SOIC package and is identified by the JR ordering code. The precision and BiFET characteristics inherited from the AD744 core give the device low input bias behavior and good DC precision, while the monolithic implementation improves channel-to-channel matching. Applications include low-frequency active filters, audio preamplifier stages, sample-and-hold interfaces, and precision ADC or DAC input buffers. When using the device, follow the manufacturer's recommended power-supply bypassing and observe the input common-mode range for the selected supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths. Stable feedback components and careful grounding are essential because the fast settling response can expose instability in poorly compensated filter stages. This page combines the AD746JR electrical characteristics, drop-in alternatives, application guidance, and practical design notes in one engineering-focused reference. It also identifies where the device differs from related dual JFET-input amplifiers, helping designers balance precision, speed, supply range, and channel matching when selecting an amplifier for an existing design.

RFQ پەیوەندی
AD746SQ - Dual 13MHz BiFET Op Amp | Analog Devices
AD746SQ

AD746SQ - Dual 13MHz BiFET Op Amp | Analog Devices

The Analog Devices AD746SQ is a dual precision BiFET operational amplifier packaged in an 8-pin CERDIP package. It combines two AD744 amplifiers on one monolithic die, a 13 MHz gain-bandwidth product, and a 500 ns settling-time capability for applications requiring accurate signal amplification and fast transient recovery. The AD746SQ operates from dual supplies, supports input and output signal paths suited to precision analog systems, and provides the close AC and DC matching inherent to amplifiers sharing a common die. A BiFET operational amplifier is a voltage-feedback amplifier whose input stage uses junction field-effect transistors. This amplifier family belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, rail-to-rail amplifiers, transimpedance amplifiers, and general-purpose voltage amplifiers. The AD746 combines low input bias current characteristics with the bandwidth and slew performance needed for active filters, sample-and-hold circuitry, instrumentation, and signal-conditioning systems. The principal features include dual-amplifier integration in one package, a 13 MHz gain-bandwidth product, and 500 ns settling performance. Monolithic construction helps maintain matching between amplifier channels, which is valuable in differential signal chains and precision filter designs. Each channel includes the conventional inputs, output, and power connections required to configure non-inverting, inverting, summing, or active-filter amplifier circuits. The AD746SQ uses the AD746 family architecture, where two AD744 BiFET operational amplifiers share one die. This construction supports consistent channel behavior and makes the device suitable where matched dynamic performance is more useful than the absolute current capability of a high-power amplifier. Its bandwidth makes it appropriate for signal paths extending beyond audio-band precision-only applications, while its BiFET input stage supports high-impedance source interfaces when source impedance and bias-current error are properly considered. Typical uses include active low-pass and band-pass filters, instrumentation preamplifiers, audio and communication-signal conditioning, analog-to-digital converter input drivers, and precision sample-and-hold systems. The dual configuration can implement two closely related channels on one board, reducing component count and helping preserve consistency between complementary or differential functions. Designers should follow the manufacturer datasheet for the exact DC supply limits, input common-mode range, output swing, offset voltage, bias current, slew rate, noise, and pin configuration. Ceramic DIP construction should also be evaluated against environmental sealing, thermal cycling, vibration, and soldering-process requirements rather than assuming that a hermetic package is interchangeable with a plastic DIP. This page combines the AD746 family architecture and package information with application guidance, verified source links, comparison parameters, and design checks for engineers evaluating the AD746SQ in precision analog signal chains.

RFQ پەیوەندی
AD7472ARUZ-REEL - 12-Bit 1.5MSPS SAR ADC | Analog Devices
AD7472ARUZ-REEL

AD7472ARUZ-REEL - 12-Bit 1.5MSPS SAR ADC | Analog Devices

The Analog Devices AD7472ARUZ-REEL is a 12-bit, 1.5 MSPS successive-approximation analog-to-digital converter (SAR ADC) with a parallel data interface, housed in a 24-pin TSSOP (RU-24) package. It operates from a single 2.7 V to 5.25 V power supply and dissipates only 3.34 mW typical at 1.5 MSPS with 3 V supplies (7.97 mW typical at 5 V), making it well-suited for power-sensitive applications. The device accepts a single-ended analog input on one channel and delivers conversion results through a high-speed parallel interface that can be directly connected to microcontrollers, DSPs, or FPGAs. An SAR (Successive Approximation Register) ADC is a type of analog-to-digital converter that uses a binary search algorithm, an internal DAC, and a comparator to digitize an analog input one bit at a time over N clock cycles, where N equals the converter's resolution. SAR ADCs occupy the middle ground between flash converters (fastest, most power-hungry) and sigma-delta ADCs (highest resolution, lowest speed), making them ideal for general-purpose industrial, instrumentation, and communication applications that need single-shot or burst-mode conversion at hundreds of kSPS to a few MSPS. The AD7472 family sits in the data acquisition -> ADC -> SAR ADC -> semiconductor taxonomy of signal-chain components. Key features include 12-bit resolution with no missing codes, a track-and-hold front end, low power consumption, and a wide input bandwidth suitable for multiplexed or single-channel systems. The wide 2.7 V to 5.25 V supply range allows designers to power the part directly from a 3.3 V or 5 V system rail, simplifying power-tree design. Industrial temperature grade (-40C to +85C) and TSSOP surface-mount packaging support compact PCB layouts. Typical applications include industrial process control, portable and battery-powered instrumentation, data acquisition systems, optical networking modules, and motor control feedback loops. The parallel interface and moderate throughput make it well matched to embedded control tasks where deterministic latency is more important than serial-link compactness. When designing with this ADC, place a low-ESR 100 nF decoupling capacitor close to the VDD pin and a bulk 10 uF capacitor on the supply rail. Provide a clean low-impedance reference voltage to the REFIN pin and ensure the analog input bandwidth is matched to the source impedance to avoid conversion errors. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes that complement the manufacturer datasheet for the AD7472ARUZ-REEL.

RFQ پەیوەندی
AD7472BRU-REEL - 12-Bit 1.5 MSPS Parallel ADC | Analog Devices
AD7472BRU-REEL

AD7472BRU-REEL - 12-Bit 1.5 MSPS Parallel ADC | Analog Devices

The Analog Devices AD7472BRU-REEL is a 12-bit, 1.5 MSPS successive-approximation analog-to-digital converter (SAR ADC) with a parallel interface, housed in a 24-pin TSSOP package. It accepts a 0 V to 2.5 V analog input, operates from a 2.7 V to 5.25 V single supply, and consumes only 3.34 mW typical at 1.5 MSPS with a 3 V supply or 7.97 mW at 1.75 MSPS with a 5 V supply. The part is specified for industrial temperature range (-40 C to +85 C) and is supplied on a 7-inch reel. A SAR ADC is a type of analog-to-digital converter that uses a binary-search successive-approximation algorithm with an internal DAC and comparator to digitize a single analog sample per conversion cycle. SAR ADCs sit in the broader hierarchy of ADC architectures (SAR -> Nyquist-rate ADC -> data converter -> mixed-signal IC -> semiconductor), favored over pipeline or delta-sigma types where low latency, deterministic single-cycle conversion, and simple digital control are required. Key features include 1.5 MSPS guaranteed throughput on the 12-bit grade (the 10-bit AD7470 in the family runs to 1.75 MSPS), a low-power CMOS process with auto-shutdown between conversions, and a high-speed parallel output bus that connects directly to microprocessors, microcontrollers, or ASICs without glue logic. The input is sampled on the falling edge of CONVST and the result is latched on the rising edge of the same signal, simplifying system timing. The internal architecture combines a track-and-hold amplifier, a precision charge-redistribution DAC, a comparator, and a successive-approximation register. The 0 V to 2.5 V input range is well suited to single-supply sensor conditioning, and the wide 2.7 V-5.25 V supply range lets the same part work in both 3 V and 5 V systems without level shifting. Typical applications include battery-powered instrumentation, data acquisition boards, CCD imaging front-ends, optical measurement systems, and process control loops. The low power and small TSSOP footprint also suit handheld test equipment and dense multi-channel acquisition boards. When designing with this ADC, budget the input settling time and ensure the source impedance seen at the analog input is well below the datasheet's recommended maximum to avoid gain errors. Use a low-impedance reference and adequate decoupling on VDD and REFIN to preserve linearity. This page synthesizes reel-packaging pricing, drop-in TSSOP alternatives, and practical design notes that are not found in the manufacturer datasheet alone, helping engineers select, source, and qualify the AD7472BRU-REEL faster.

RFQ پەیوەندی
AD7472BRZ - 12-Bit 1.5 MSPS ADC | Analog Devices
AD7472BRZ

AD7472BRZ - 12-Bit 1.5 MSPS ADC | Analog Devices

The Analog Devices AD7472BRZ is a 12-bit, single-channel, successive-approximation analog-to-digital converter with a parallel output interface, conversion throughput up to 1.5 MSPS, and a 24-lead SOIC package. It operates from a single 2.7 V to 5.25 V supply and accepts an analog input range of 0 V to 2.5 V. The low-power architecture supports portable instrumentation, industrial control, sensor acquisition, and data-capture systems where a compact, low-noise ADC is required. An ADC converts a continuously varying analog voltage into a numerical value for processing by a microprocessor, digital signal processor, or programmable logic. The AD7472 belongs to the successive-approximation, or SAR, ADC family. SAR converters repeatedly compare the sampled input against an internal reference and a weighted capacitor array. This architecture combines predictable latency, direct sampling control, and a parallel data interface without the clock and filtering complexity of a pipeline converter. Key characteristics of the AD7472 include 12-bit resolution, throughput up to 1.5 MSPS, a single 2.7 V to 5.25 V analog and digital supply, and a 0 V to 2.5 V input range. Conversion is initiated by the falling edge of CONVST, while BUSY indicates that the conversion is in progress. According to the manufacturer product information, BUSY returns low 531.66 ns after the falling CONVST edge when the internal clock operates at 26 MHz. The parallel interface simplifies connection to older DSP and FPGA systems that do not use serial protocols. Typical power figures depend on supply voltage and throughput. The AD7472 dissipates approximately 3.34 mW at 1.5 MSPS with 3 V supplies and 7.97 mW at 1.75 MSPS with 5 V supplies, as listed in the component datasheet. This operating range makes the converter suitable for battery-powered measurement equipment, where power dissipation affects both run time and thermal design. The industrial temperature option covers -40°C to +85°C. The AD7472BRZ is used in portable data loggers, process-control modules, industrial sensor interfaces, ultrasonic measurement systems, and embedded acquisition boards. In these systems, the 12-bit code supports measurement of 2.5 V full-scale signals with an input-referred quantization step of approximately 610 µV when the full 0 V to 2.5 V range is used. External reference and input conditioning circuitry remain important when accuracy, common-mode rejection, or overrange behavior must be controlled. For implementation, route the analog input and reference paths away from digital switching nodes, place input and reference decoupling capacitors close to their associated pins, and use a short, symmetric digital-output routing pattern. Check the acquisition timing against the 531.66 ns conversion indication and the receiving device setup time. Request a quote on this page for current commercial availability, lead time, and orderable quantities.

RFQ پەیوەندی
AD7472YRU - 12-Bit 1.5 MSPS ADC | Analog Devices
AD7472YRU

AD7472YRU - 12-Bit 1.5 MSPS ADC | Analog Devices

The Analog Devices AD7472YRU is a 12-bit, single-channel, parallel-output successive-approximation analog-to-digital converter capable of 1.5 MSPS throughput from a single 2.7 V to 5.25 V supply. It is packaged in a 24-pin TSSOP surface-mount package for compact data-acquisition and signal-conditioning systems. An ADC is a data-acquisition IC that converts an analog voltage into a digital code. The AD7472 belongs to the parallel-output SAR ADC family, combining a 12-bit resolution, 1.5 MSPS sampling capability, and low 4 mW power operation in a single package. The AD7470 is the related 10-bit member of the family, while AD7472 provides the higher resolution needed when the input-to-output quantization step must be smaller. Key characteristics include 12-bit resolution, 1.5 MSPS maximum throughput, a 2.7 V to 5.25 V analog supply range, and a low-noise internal reference. The parallel interface presents the conversion result across dedicated digital output pins, allowing direct connection to a microcontroller, FPGA, DSP, or logic device without requiring a serial data link. The successive-approximation architecture performs one conversion through a sequence of internal comparator decisions. Its throughput is suitable for industrial process monitoring, sensor acquisition, portable measurement equipment, and embedded control loops. Because the interface is parallel, the host processor must be able to accept and latch 12 bits of conversion data within the available acquisition interval. A typical implementation places the AD7472 close to the analog input source and routes its digital outputs to a logic device. Short analog traces reduce pickup of noise and switching artifacts, while a solid ground plane and careful separation of analog and digital return currents help preserve conversion accuracy. The manufacturer datasheet should be consulted for the complete pin-description table, recommended input and reference circuits, and acquisition timing diagrams. The AD7472YRU is suited to designers who require a parallel-output SAR converter with a compact 24-pin TSSOP footprint. AD7472ARU and AD7472BRU provide related temperature-grade choices, while the AD7470 members trade resolution for higher throughput. This page also organizes pricing evidence, replacement guidance, comparison parameters, and practical design notes for faster component selection.

RFQ پەیوەندی
AD7472YRZ - 12-Bit 1.5 MSPS ADC | Analog Devices
AD7472YRZ

AD7472YRZ - 12-Bit 1.5 MSPS ADC | Analog Devices

The Analog Devices AD7472YRZ is a 12-bit, single-channel, successive-approximation analog-to-digital converter with a throughput rate up to 1.5 MSPS, a 2.7 V to 5.25 V analog supply range, and a 24-lead SOIC package. It converts an analog input voltage into a 12-bit parallel digital result for data-acquisition, instrumentation, industrial-control, and embedded measurement systems. An ADC is a data-conversion integrated circuit that samples an analog voltage and represents it as digital data. Within the analog-to-digital converter hierarchy, the AD7472 is a successive-approximation, or SAR, ADC: an internal sample-and-hold circuit captures the input, and successive comparison steps determine each output bit. A parallel-output ADC exposes the converted word directly on digital pins, reducing the need for a serial interface and simplifying connections to suitable processors, FPGAs, or data-capture logic. The AD7472 combines 12-bit resolution with a maximum 1.5 MSPS conversion rate. Its single analog input and 2.7 V to 5.25 V operating supply support compact mixed-signal designs where conversion speed, resolution, and low power consumption are more important than input multiplexing. The Analog Devices AD7472 family is identified as a high-speed, low-power SAR ADC, while the AD7472YRZ is offered in the 24-terminal SOIC outline. Its 0 V to 2.5 V analog input range makes the converter appropriate for sensor interfaces and control signals scaled to that interval. The parallel word-access architecture allows the twelve-bit result to be captured directly rather than serialized on a dedicated data bus. Designers must still account for acquisition time, conversion time, input settling, reference accuracy, digital timing, and analog noise when defining the overall sample rate. Typical uses include industrial process monitoring, temperature and pressure sensor acquisition, laboratory measurement equipment, motor and power-system control, and embedded data-logging systems. A 1.5 MSPS conversion capability is useful when a design needs more frequent measurements than a slow general-purpose ADC can provide, while 12-bit resolution provides 4096 discrete codes across the selected input range. The principal design consideration is signal integrity. Place the input and reference networks close to the device, use a low-noise reference, keep analog and digital return currents separated, and observe the datasheet timing for sample acquisition and conversion. The SOIC footprint also requires adequate copper area and careful assembly layout for stable thermal and analog performance. This page combines the Analog Devices product specifications with practical acquisition guidance, verified drop-in references, packaging details, and application-oriented design notes. It helps engineers evaluate the AD7472YRZ against pin-compatible family members and plan the surrounding analog, digital, and layout implementation.

RFQ پەیوەندی
AD7475ARM-REEL7 - 12-bit 1MSPS SAR ADC | Analog Devices
AD7475ARM-REEL7

AD7475ARM-REEL7 - 12-bit 1MSPS SAR ADC | Analog Devices

The Analog Devices AD7475ARM-REEL7 is a 12-bit, high-speed, low-power successive-approximation register (SAR) analog-to-digital converter (ADC) that operates from a single 2.7V to 5.25V supply and delivers throughput rates up to 1 MSPS. Packaged in an 8-pin MSOP (RM-8) and supplied on a 7-inch reel, the part integrates a low-noise wide-bandwidth track-and-hold amplifier capable of processing input signals beyond 1 MHz. The 2.5V reference is applied externally to the REF IN pin, allowing designers to optimise dynamic range for each application by selecting the most appropriate external reference. The serial interface is compatible with DSP, MICROWIRE, QSPI and SPI, allowing easy connection to the majority of microcontrollers and DSPs without glue logic. A SAR ADC is a successive-approximation architecture that converts an analog input to a digital code through a binary-search algorithm using an internal DAC and comparator, achieving an excellent balance of speed, accuracy and power efficiency. SAR ADCs sit within the broader category of data converters (ADC/DAC) and are widely preferred for multiplexed channel acquisition, motor control feedback loops, and precision instrumentation where low latency and deterministic sampling are required. The AD7475 family (AD7475/AD7495) occupies the lower-power, high-speed segment of the SAR market, targeting portable, industrial and process-control designs. Key specifications include 12-bit resolution with no missing codes, 1 MSPS throughput, 4.5 mW typical power dissipation at 1 MSPS with 3V supply (10.5 mW at 5V), and a flexible VDRIVE function that sets the serial-interface logic level independently of the analog supply. The high-bandwidth track-and-hold amplifier handles input frequencies well above the Nyquist limit, supporting undersampling and accurate acquisition of fast transients. The serial interface can be configured for 3-wire or 4-wire SPI/MICROWIRE/QSPI/DSP operation, simplifying integration across a broad range of host platforms. Typical applications include battery-powered instrumentation, data acquisition systems, motor control feedback, portable medical devices and industrial process control. The wide 2.7V to 5.25V supply range and low power dissipation make the AD7475ARM-REEL7 particularly attractive for remote, battery-powered sensor nodes where energy budget is critical. When designing with the AD7475, provide a low-impedance external reference (such as the AD780 or ADR02) for full 12-bit performance, and keep digital and analog ground returns separated with a single-point join to preserve noise immunity.

RFQ پەیوەندی
AD7475BRMZ-REEL - 12-Bit 1MSPS SAR ADC | Analog Devices
AD7475BRMZ-REEL

AD7475BRMZ-REEL - 12-Bit 1MSPS SAR ADC | Analog Devices

The Analog Devices AD7475BRMZ-REEL is a 12-bit, high-speed, low-power successive-approximation analog-to-digital converter (SAR ADC) that operates from a single 2.7 V to 5.25 V supply and delivers throughput rates up to 1 MSPS. Packaged in an 8-pin MSOP (RM-8) and supplied on a 7-inch reel, it integrates a low-noise, wide-bandwidth track-and-hold amplifier capable of handling input frequencies in excess of 1 MHz. The external 2.5 V reference applied at REF IN, combined with the on-chip serial interface, makes it well suited for compact mixed-signal designs. A SAR (Successive Approximation Register) ADC is a precision converter architecture that uses a binary-search algorithm against an internal DAC to digitize the input voltage in N clock cycles. SAR ADCs sit in the broader taxonomy of analog-to-digital converters -> data converters -> mixed-signal ICs -> signal chain semiconductors, and they are favoured over pipeline or flash ADCs where low latency, deterministic sampling, and low power consumption are required at moderate resolutions (8 to 16 bits). Key features include a 1 MSPS conversion rate, 4.5 mW typical power dissipation at full speed, a flexible serial (SPI/QSPI/MICROWIRE/DSP-compatible) interface, and the proprietary VDRIVE function that allows the digital I/O logic levels to be set independently of the analog supply. The device offers a typical INL of ±1 LSB and operates across the industrial -40C to +85C temperature range, ensuring stable performance in harsh environments. From an architectural standpoint, the AD7475 uses a charge-redistribution DAC array combined with a high-bandwidth sample-and-hold capable of digitizing signals well beyond the Nyquist frequency. The serial clock can be applied up to 20 MHz, supporting the full 1 MSPS throughput while keeping the digital interface noise isolated from the analog input stage, an essential consideration for high-precision measurement systems. Typical applications include battery-powered instrumentation, portable data acquisition systems, optical sensor front-ends, isolated industrial process controls, and precision medical instruments such as patient monitoring devices. Designers also deploy it in motor control feedback loops and programmable logic controller (PLC) analog input modules where deterministic latency and low power are equally important. When designing with this device, ensure the reference decoupling capacitor is placed as close as possible to the REF IN pin and use a clean, low-noise analog ground pour to preserve 12-bit accuracy. The VDRIVE pin should be tied to the host MCU's logic supply to guarantee proper SPI timing margins at full 1 MSPS throughput. This page synthesizes distributor pricing, drop-in compatible replacements, and practical PCB layout notes that extend beyond the manufacturer datasheet, giving engineers a single authoritative reference for the AD7475BRMZ-REEL.

RFQ پەیوەندی
AD7476AAKSZ-REEL - 12-bit 1MSPS SAR ADC SC-70 | ADI
AD7476AAKSZ-REEL

AD7476AAKSZ-REEL - 12-bit 1MSPS SAR ADC SC-70 | ADI

The Analog Devices AD7476AAKSZ-REEL is a 12-bit, 1 MSPS successive-approximation register (SAR) analog-to-digital converter (ADC) housed in a 6-lead SC-70 package. It operates from a single 2.35 V to 5.25 V power supply, consumes low power, and provides one analog input channel with a throughput rate up to 1 MSPS. An ADC is a data converter that transforms a continuous analog voltage into a discrete digital code. SAR (Successive Approximation Register) ADCs use a binary-search algorithm combined with an internal DAC to resolve each conversion in a fixed number of clock cycles, balancing speed, accuracy, and power efficiency. Within the converter hierarchy, this places the AD7476A in the precision, low-power, successive-approximation sub-family, well-suited for battery-powered and space-constrained instrumentation. Key features of the AD7476A include 12-bit resolution, 1 MSPS throughput, a wide 2.35 V to 5.25 V single-supply input range, low power consumption, and a small 6-lead SC-70 outline. The -REEL suffix denotes tape-and-reel packaging for high-speed pick-and-place assembly. The part shares pinout with the 10-bit AD7477A and 8-bit AD7478A, allowing designers to migrate resolution by simply changing the device. Typical applications include portable and battery-powered systems, instrumentation, data acquisition front-ends, optical sensor front-ends, and general-purpose analog monitoring in industrial, medical, and consumer designs. The SC-70 footprint makes it attractive where PCB real estate is at a premium. When designing with this device, provide adequate decoupling near the supply pin and ensure the analog input is bandwidth-limited to avoid aliasing. The wide supply range simplifies integration into both 3.3 V and 5 V systems. This page synthesizes distributor pricing, verified pin-compatible alternatives, and practical design notes curated for engineers — beyond what is found in the manufacturer datasheet.

RFQ پەیوەندی
AD7476ABKSZ-REEL - 12-Bit 1 MSPS SAR ADC, SC-70-6 | Analog Devices
AD7476ABKSZ-REEL

AD7476ABKSZ-REEL - 12-Bit 1 MSPS SAR ADC, SC-70-6 | Analog Devices

The Analog Devices AD7476ABKSZ-REEL is a 12-bit, 1 MSPS successive-approximation register (SAR) analog-to-digital converter housed in a 6-lead SC-70-6 package. It operates from a single 2.35 V to 5.25 V power supply, features a single-ended analog input, and is rated over the -40C to +85C industrial temperature range. The part pairs a 12-bit resolution with throughput up to 1 million samples per second, making it one of the smallest form-factor high-speed ADCs in the ADI portfolio. An SAR ADC is a type of data converter that uses a successive-approximation register and an internal track-and-hold to digitize an analog input in a fixed number of clock cycles (typically one per N-bit cycle). As a sub-family of Nyquist-rate data converters, SAR ADCs sit between sigma-delta converters (higher resolution, lower speed) and flash ADCs (highest speed, lowest resolution) within the ADC taxonomy. ADCs are integrated circuits that bridge real-world analog signals to digital processors and microcontrollers across the broader mixed-signal and data-acquisition IC hierarchy. Key features include very low power consumption, a high-speed SPI/QSPI/MICROWIRE-compatible serial interface, and an automatic power-down between conversions that drops current draw dramatically when the part idles between samples. The 6-lead SC-70 footprint makes it one of the smallest 1 MSPS ADCs available, enabling analog front-end placement next to sensors on space-constrained PCBAs. The device uses a charge redistribution DAC architecture with an internal reference and a high-bandwidth input track-and-hold to deliver 12-bit linearity across the full input common-mode range. Because conversion is deterministic in time (no pipeline latency), the AD7476A is well suited to event-triggered sampling, multiplexed-channel sequencing, and motor-control feedback loops where deterministic group delay is required. Typical applications include battery-powered portable instrumentation, hand-held multimeters and data loggers, transducer signal conditioning chains, isolated industrial sensors, optical-module monitoring, and general-purpose embedded analog front ends. Designers select this part specifically when PCB area, single-rail operation, and deterministic conversion latency are more important than the very highest absolute sampling rates. When laying out a board, place the 0.1uF supply-decoupling capacitor as close as possible to the VDD pin, keep analog and digital grounds separated with a single-point stitch near the IC, and route the SCK, SDATA, and /CS digital traces away from the analog input net. Always drive /CS low before SCK edges and observe the tCONVERT timing budget for accurate 1 MSPS operation. This page synthesizes ADI distributor pricing, drop-in alternatives, and SC-70 layout/design notes that go beyond the bare datasheet to give you a faster procurement and bring-up decision.

RFQ پەیوەندی