Logic ICs
بەرهەمەکان (720+)
MC14024BD - 7-Bit Binary Ripple Counter | onsemi
The onsemi MC14024BD is a 7-bit binary ripple counter IC with one counter element, negative-edge clock triggering, and a 14-pin SOIC package. It operates across a 3 V to 18 V supply range and provides buffered outputs for each of its seven counter stages. The device is designed for frequency division, event counting, timing generation, and digital state sequencing in conventional CMOS logic systems. A binary ripple counter is a sequential digital logic device that advances through 2^n states as clock pulses arrive. The MC14024BD implements seven cascaded stages, allowing a single clock input to produce division ratios from 2 through 128 when the corresponding output stages are used. Its 3 V to 18 V supply range places it between conventional 5 V logic and higher-voltage CMOS-compatible equipment. The principal features include short propagation delays, high maximum clock rates, buffered stage outputs, and hysteresis on the clock input for improved noise immunity. The reset input uses standard noise immunity. Unlike a synchronous counter, the ripple architecture changes adjacent output stages sequentially, which can create accumulated decoding delay when several outputs are decoded simultaneously. Each counter stage is buffered, allowing the outputs to drive external logic while maintaining predictable logic levels. The manufacturer describes the MC14024BD as a pin-for-pin replacement for the CD4024B. The component is also identified as Pb-free and RoHS compliant in the manufacturer datasheet. A qualified NLV-prefixed option exists for automotive and other applications requiring unique site and control changes, but the exact NLV ordering code is not identified here. Typical uses include dividing a system clock into slower timing intervals, counting recurring events, sequencing digital operations, generating programmable delays, and maintaining a modulo count in industrial control, instrumentation, and embedded peripheral logic. The counter can also operate as a one-shot or binary state register when its clock and reset inputs are driven according to the application requirements. Designers should account for ripple propagation delay when decoding multiple outputs, allow sufficient clock rise and fall times for reliable CMOS operation, and use hysteresis benefits when the clock source is noisy. Decoupling capacitors should be placed close to the supply pins, while unused inputs must be held at a defined logic level. This page also organizes the available sourcing, comparison, and engineering guidance around the exact MC14024BD ordering code. For a new design, the MC14024BD is most appropriate when a 14-pin SOIC footprint, seven binary count stages, and a 3 V to 18 V operating range are required. Because it is a ripple counter, a synchronous counter may be preferable when simultaneous output transitions must remain tightly aligned. For legacy repairs, confirm the exact pinout and electrical limits in the manufacturer datasheet before substituting an equivalent device onto an existing board.
MC14024BF - 7-Bit CMOS Ripple Counter IC | onsemi
The onsemi MC14024BF is a 7-bit, asynchronous binary ripple counter IC with a supply voltage range of 3 V to 18 V, operating temperature range of -55°C to 125°C, and a 14-terminal PDSO14 package. It provides seven buffered counter outputs, negative-edge clock triggering, upward counting, and standard CMOS integration. A binary ripple counter is a logic IC that advances through a sequence of binary values when an external clock edge is applied. The MC14024BF belongs to the CMOS counter and divider category within the broader hierarchy of digital logic, logic ICs, and integrated circuits. Its seven stages can be used independently as modulo counters, frequency division stages, state-counting elements, or a complete seven-bit counter when the output stages are chained internally. The key operating features include seven counter stages, buffered outputs, negative-edge triggering, asynchronous counting, and hysteresis on the clock input for improved noise immunity. The reset input uses standard noise immunity. These characteristics make the device useful when a design requires a simple counter without a dedicated microprocessor or programmable logic. The 3 V to 18 V supply range permits operation across common low-voltage and conventional CMOS supply systems. The ripple architecture advances one stage per clock event, with propagation delay accumulating through the cascaded stages. Each output is buffered, allowing individual stage outputs to be observed or used in external logic. Because the maximum operating frequency and timing limits depend on operating voltage and temperature, the onsemi MC14024B datasheet should be consulted for the applicable values before relying on the counter at a system clock edge that approaches the device limit. Typical applications include digital event counting, pulse accumulation, seven-segment sequencing control, industrial timing, frequency division, laboratory instrumentation, and embedded control logic. The MC14024BF can count external events when the input signal remains within the electrical limits of its clock input. Its buffered outputs are particularly useful when one or more counter states must drive gates, indicators, or control signals independently. For reliable implementation, connect the reset to a defined inactive state, maintain clean clock edges, and observe the supply-voltage and temperature limits of 3 V to 18 V and -55°C to 125°C. Because ripple-counter outputs can change successively after a clock edge, downstream circuitry should not treat the seven outputs as a simultaneous encoded bus unless the timing requirements are specifically analyzed. This page combines the onsemi counter architecture with application guidance, verified parameter availability, comparison fields, and practical implementation notes. It helps engineers distinguish the MC14024BF from other counter functions and identify what must be checked in the manufacturer datasheet before releasing a PCB or production design.
MC14029BF - 4-Bit Binary/Decade Up-Down Counter | onsemi
The onsemi MC14029BF is a 4-bit binary/decade up-down counter built with complementary MOS P-channel and N-channel enhancement-mode devices in a 16-pin SOIC package. It supports positive-edge-triggered counting, operates in binary or BCD mode, and provides separate carry and borrow outputs for multi-digit arithmetic and digital sequencing. The MC14029BF is the F-package ordering code associated with the MC14029B counter family and is identified by onsemi as the MC14029B Binary/Decade Up/Down Counter. A binary/decade up-down counter is a synchronous logic circuit that increments or decrements a four-bit numerical state when clocked. Binary mode represents values from 0 through 15, while decade mode supports decimal counting from 0 through 9. In the broader electronics hierarchy, the MC14029BF is a counter IC, which belongs to the logic IC and digital semiconductor categories. Its architecture combines D-type flip-flop stages with gating that permits counting in either direction, making it useful for modular arithmetic, stepper-motor position tracking, frequency division, and programmable event sequencing. The principal feature of the MC14029BF is its bidirectional counting capability. A separate up/down control determines the counting direction, while the clock input advances the selected state on the active edge. The four parallel outputs Q0 through Q3 expose the current count for direct observation, decoding, display, or control. A cascade input allows multiple counters to form larger counting systems, and the carry and borrow outputs identify overflow or underflow conditions. A parallel load input supports initialization to a predefined count, while master reset provides a common clearing mechanism. Because the device is implemented in complementary MOS technology, it combines low-power operation with the voltage-level behavior expected from the MC14029B logic family. The counter can be used either as a binary counter or as a decade counter, allowing the same physical circuit to serve digital clocks, industrial sequence counters, and modular arithmetic functions. Because a cascade connection introduces propagation delay between stages, designers should account for settling time when interpreting overflow signals or when several stages must transition coherently. Typical uses include digital frequency dividers, programmable event counters, bidirectional position indicators, decade timing chains, and four-bit arithmetic sequences. In a cascaded display or timing system, one MC14029BF can count units while additional devices count tens and higher groups. The carry output can advance the next stage during an up-count, while the borrow output can decrement it during a down-count. A parallel-load path can also initialize the counter to a nonzero value, which is useful in presettable timers and sequence generators. PCB implementation should preserve the pin assignments of the 16-pin SOIC footprint and route clock and control signals away from sensitive analog or high-speed nets. The clock input is especially important in a counter because excessive clock-edge noise can cause false increments or decrements. Keep traces short, provide a low-impedance ground reference, and avoid placing slow control inputs immediately beside the clock net when the layout permits. Follow the manufacturer’s application information for recommended decoupling and unused-input treatment. This product page combines the manufacturer’s function description with package, pinout, sourcing, and engineering guidance. It also distinguishes the MC14029BF from related ordering codes while emphasizing that final replacement decisions require checking the complete truth table, timing limits, voltage limits, and operating-temperature requirements for the specific design.
MC14040BD - 12-Bit Binary Counter, 3-18 V | onsemi
The onsemi MC14040BD is a 12-stage ripple-carry binary counter operating from 3 V to 18 V in a 16-pin SOIC package. The device advances its count on the negative-going edge of the clock and provides twelve binary outputs for frequency division, event counting, timing, and sequential control. Its monolithic construction uses MOS P-channel and N-channel enhancement-mode devices, while an input wave-shaping circuit supports reliable clock handling. A binary counter is a sequential digital-logic component that stores an integer count and advances that count when triggered. The MC14040B belongs to the counter and divider hierarchy within logic ICs. Its twelve stages divide the input clock by powers of two, allowing Q0 through Q11 to represent successive binary bits of the accumulated count. This structure supports both binary counting and programmable frequency division when selected outputs are used as the feedback clock. The principal features include a 12-bit count capacity, negative-edge clock operation, 3 V to 18 V operating voltage, and 16-pin SOIC construction. The ripple-carry architecture provides multiple count taps without requiring a microprocessor or programmable logic device. Because the outputs are ordinary CMOS logic levels, the counter can be combined with gates, flip-flops, display drivers, and timing circuits in industrial control, instrumentation, and embedded systems. Operationally, the device accepts a clock transition at the CLK input and transfers state through twelve internal stages. A master reset input initializes the count, while the twelve Q outputs expose the binary count bits. The manufacturer identifies time-delay circuits, counter controls, and frequency division among the intended applications. Designers should account for propagation delay through the ripple chain when cascaded counters must present a coherent multi-bit count to downstream logic. The MC14040BD is suitable for industrial control and automation, frequency-divider modules, programmable timing references, digital time-delay circuits, event counters, and low-cost embedded sequencing systems. It is especially useful when a controller needs a repeatable binary count derived from an external clock without allocating a microcontroller input or software counter. For reliable implementation, route the clock and reset traces away from the Q outputs, keep the supply return path short, and place the normal bypass capacitor close to the supply pins. Confirm that the clock amplitude and transition times meet the operating requirements for the selected supply voltage, and account for counter propagation delay when multiple output bits are sampled simultaneously. This page combines the manufacturer device characteristics with package-level implementation guidance, comparison parameters, and application-oriented design notes. Those engineering details help engineers evaluate the MC14040BD for a new counter design before completing the PCB schematic, timing analysis, and qualification plan.
MC14060BF - 14-Bit Counter with Oscillator | onsemi
onsemi MC14060BF is a 14-stage binary ripple counter with an on-chip oscillator buffer, supplied in a 16-pin SOIC package. It provides 14 binary counter outputs, a common reset function that clears all outputs and disables the oscillator, and an oscillator arrangement that supports RC or crystal timing networks. The clock advances the counter on a negative transition, making the device suitable for frequency division, timing generation, pulse counting, and periodic control functions. A binary ripple counter is a digital sequential circuit in which each counting stage drives the next stage. The MC14060BF belongs to the counter and divider hierarchy within CMOS logic ICs. Its integrated oscillator removes the need for a separate clock generator when a free-running time base is required. If an external clock is available, the clock input allows the circuit to operate as a divide-by-2 through divide-by-16,384 counter chain. The on-chip oscillator buffer supports both resistor-capacitor and crystal oscillator configurations. The onsemi datasheet also identifies a Schmitt-trigger clock input, which improves switching behavior when the clock waveform has a slow edge or appreciable noise. Buffered outputs are available from stages 4 through 10 and stages 12 through 14, providing usable drive capability for selected divider outputs in frequency-divider and timing applications. A common reset input places every counter output into the zero state and disables the oscillator. This behavior allows a system controller to establish a known timing origin, synchronize multiple events, or restart a periodic sequence. Each negative transition on the clock advances the count by one, and the 14 counter stages provide a total division ratio of 16,384 when the highest-order output is used. Typical applications include digital clocks and timers, industrial sequence controllers, periodic pulse generators, frequency dividers, phase-shift systems, and embedded control systems requiring a local time base. The 16-pin SOIC package also allows the counter to be used on conventional surface-mount control boards where a larger leaded package would be unnecessary. For reliable oscillator operation, keep the oscillator and clock traces short and place timing components close to the device. When using an RC network, validate component tolerance and temperature behavior across the intended operating range. For crystal timing, follow the manufacturer connection and load recommendations and maintain clean return paths to reduce false clock transitions. This product page combines the MC14060B functional description, package information, drop-in alternatives, comparison parameters, and practical oscillator and layout guidance to support faster component selection and implementation.
MC14071BDR2G - Quad 2-Input OR Gate, 3-18V CMOS, SOIC-14 | onsemi
The onsemi MC14071BDR2G is a B-suffix series Quad 2-Input OR Gate built with P-channel and N-channel enhancement-mode CMOS transistors in a single monolithic structure, supplied in a 14-pin SOIC package. It contains four independent 2-input OR gates and operates across a wide supply voltage range of 3 V to 18 V DC, with logic-level compatibility across the full range. An OR gate is a fundamental combinational logic device that outputs a logic HIGH whenever at least one of its inputs is HIGH; four such gates share a common power rail in the MC14071B, forming part of the 4000-series CMOS logic family. This family sits within the broader hierarchy: logic gate -> combinational logic -> digital IC -> integrated circuit -> semiconductor. The MC14071BDR2G is widely used as a glue-logic building block in mixed-signal systems, replacing discrete transistors and providing reliable logic OR-ing where board-level routing is critical. Key features include extremely low quiescent supply current (typically 0.5 nA per gate at 5 V), high noise immunity of 45% of VDD minimum, and 5 V, 10 V, and 15 V parametric ratings per JEDEC JESD 20. Output drive is symmetric CMOS with balanced rise/fill characteristics and ESD protection on all inputs. The MC14071BDR2G's buffered-output architecture provides consistent fan-out and clean logic levels across the supply range, while inputs are diode-protected against over-voltage transients. The MC14071BDR2G uses a complementary MOS (CMOS) process in which P-channel pull-ups and N-channel pull-downs are co-integrated; this yields the family's hallmark near-zero quiescent current (current flows only during switching), making it ideal for battery-powered equipment. Designers can cascade gates for combinatorial logic, use the part as a logic-level translator between 5 V and 12 V domains, or wire OR multiple interrupt sources together for MCU monitoring. The 14-SOIC footprint is footprint-compatible with the rest of the MC140xx family, allowing easy migration to NAND, AND, NOR or XOR equivalents when board real-estate is reserved. Typical applications for the MC14071BDR2G include industrial control logic, automotive body electronics, battery-powered instrumentation, alarm-system OR-tying, and general-purpose glue logic in mixed-signal PCBs. The wide 3-18 V supply tolerates 12 V and 15 V analog rails, simplifying designs that interface to legacy analog sections. When designing with this part, observe standard CMOS handling precautions: tie all unused inputs to VDD or GND to prevent floating-input oscillation and extra current draw. The MC14071BDR2G is a direct functional replacement for the legacy CD4071B from Texas Instruments and is drop-in compatible on most 14-pin SOIC layouts.
MC145026D - 9-Line CMOS Encoder IC | NXP | 16-SOIC
The NXP Semiconductors MC145026D is a CMOS encoder integrated circuit designed to encode nine information lines and transmit the resulting data serially for remote-control and security applications. It supports nine input lines with either trinary low, high, or open states or binary low and high states, providing 19,683 possible trinary codes. The device is packaged in a 16-pin SOIC surface-mount package. A remote-control encoder IC is part of the broader interface and logic semiconductor hierarchy used to convert physical switch or control states into a compact serial signal. The MC145026D is intended for use with the MC145027 decoder family, allowing an encoded command or access-code word to be transmitted over a wired link and recovered by a compatible receiving circuit. Its repeated transmission behavior increases security by making the received word more resistant to simple single-event transmission errors. The encoder accepts a transmit-enable input to initiate a serial encoding sequence. During normal operation, the nine input pins can represent individual control functions such as multiple button states, access-code positions, or discrete logic conditions. The trinary mode is especially useful for systems that need more than binary combinations, while binary mode can simplify the interface when each control line is restricted to two valid states. The MC145026D is a dedicated encoder rather than a general-purpose microcontroller or communication transceiver. It does not require firmware, and its function is determined by the electrical state of the input pins and the transmit-enable control. This makes it suitable for simple, compact remote-control systems, keypad-based access devices, industrial control panels, and security-related key-entry modules where a hardware encoder is preferable to a programmable controller. As a legacy CMOS logic device, the principal design considerations are operating voltage compatibility, input-state definitions, timing around the transmit-enable signal, and correct receiver pairing. The MC145026D should be used with an appropriate MC145027-family decoder and verified against the NXP datasheet for pin functions, electrical timing, and operating conditions. The part’s documented lifecycle status is obsolete, so new designs should confirm availability and consider a supported alternative before committing to a production release. This page consolidates the manufacturer’s functional description, package information, application guidance, and replacement considerations into a design-focused reference for engineers evaluating the MC145026D in legacy remote-control systems.
MC145028P - 9-Line CMOS Remote Control Decoder | NXP
NXP MC145028P is a CMOS remote-control decoder IC designed for the decoding half of an encoder/decoder pair, with nine address lines, a 16-pin through-hole DIP package, and a 0.300-inch, 7.62 mm body width. It receives a serially encoded command stream, checks the transmitted address, and presents the decoded data and valid-data indication to the associated system controller. A remote-control decoder is a logic IC that translates a serial communication stream into usable control signals. The MC145026, MC145027, and MC145028 devices form encoder/decoder families for remote-control applications. In such a hierarchy, an encoder converts parallel command information into a serial waveform, while a decoder receives that waveform, validates the address information, and reconstructs the data. The MC145028P is therefore a semiconductor interface and logic device rather than a general-purpose microcontroller or analog receiver. The MC145028P supports nine encoded information lines, as described for the MC145026/27/28 encoder-and-decoder family. Its CMOS construction supports low-power remote-control system implementations, while the 16-pin DIP package facilitates through-hole assembly, prototyping, repair, and legacy industrial equipment. The identified package is a 0.300-inch, 7.62 mm 16-DIP configuration. Operating details beyond the package and basic device function require confirmation from the manufacturer datasheet. The decoder is intended to work with a compatible remote-control transmitter, commonly an MC145026 encoder. The transmitter serializes address and command information when its transmit-enable signal is asserted. The receiver reconstructs the transmitted information and indicates whether the received command corresponds to the selected address. This arrangement allows one receiver system to respond selectively to one transmitter or group of transmitters. Typical uses include industrial remote-control panels, access and equipment-control systems, telemetry links, model or process-control interfaces, and legacy embedded systems. The 16-DIP format is especially useful where a through-hole replacement is required, but board area and manual insertion limitations make the device less suitable for compact new portable products. When designing around the MC145028P, match the encoder waveform, address coding, timing, and interface voltage levels rather than selecting the receiver from package appearance alone. Confirm the complete pin assignment and electrical limits in the manufacturer datasheet before routing a new PCB. This page combines device identity, package information, sourcing guidance, application fit, and design cautions for engineers evaluating legacy or repair applications.
MC14503BD - Hex 3-State Buffer, 3-18V | onsemi
The onsemi MC14503BD is a hex non-inverting buffer with six high-impedance, 3-state outputs and two independent disable controls. The device operates from 3 V to 18 V, supports common-bus multiplexing, and is packaged in a 16-pin SOIC for surface-mount assembly. It is designed to provide high current source and sink capability while allowing multiple drivers to share a bus without active output contention. A hex 3-state buffer is a digital logic device that passes each input signal to its corresponding output without inversion. When an output is disabled, it enters a high-impedance state and releases the connected bus line. This tri-state behavior places the MC14503BD in the wider logic-buffer and bus-driver hierarchy, supporting functions from signal isolation and level buffering to bus multiplexing and data-bus sharing. The MC14503B family provides two disable controls. A high level on Disable A places the outputs of buffers 1 through 4 into the high-impedance state, while a high level on Disable B controls the outputs of buffers 5 and 6. This arrangement allows two groups of three outputs to be enabled or disabled independently, which is useful when several devices drive a shared communication or address bus. The 3 V to 18 V operating range makes the MC14503BD suitable for both 5 V and legacy multi-voltage logic systems. Its 16-pin SOIC construction supports compact, high-density PCB layouts while preserving the pin arrangement associated with the MC14503B family. Because the output impedance is high while disabled, only one buffer should actively drive a shared node at a time. Typical uses include bidirectional bus isolation, address decoding, memory-bank selection, peripheral multiplexing, and level translation within mixed-voltage systems. Its non-inverting signal path preserves data polarity, allowing the device to be inserted between a source and destination logic node without changing bus timing or data format. When assigning PCB signals, use the manufacturer pin-description table to confirm the data, disable, supply, and ground connections. Keep the disable traces away from high-current switching nodes, and confirm that every shared output node has exactly one enabled driver during any operating state.
MC14503BF - Hex 3-State Non-Inverting Buffer | onsemi
onsemi MC14503BF is a hex non-inverting buffer with six 3-state outputs, a 5 V nominal operating voltage, 150 ns propagation delay, and a 16-lead PDIP package. The device provides high-current source and sink capability, making it suitable for common-bus applications where multiple logic devices must share an interconnect. Two independent disable controls allow buffers 1 through 4 and buffers 5 through 6 to be placed in the high-impedance state independently. A 3-state buffer is a digital interface component that can present a valid logic level, actively drive a bus, or electrically release the bus with a high-impedance output. The three-state function distinguishes it from a conventional buffer, which continuously drives its output. By placing several drivers in parallel, a system can reduce contention when only one device is active. The hex organization provides six non-inverting channels in one package. The MC14503BF supports common-bus architectures where source and sink capability must accommodate driven logic levels. Its 150 ns propagation delay provides a defined timing relationship between an input transition and the corresponding output transition. The 50 pF load-capability figure identifies a useful bus-loading condition when evaluating interconnect behavior. Two disable inputs add local bus-segment control without requiring individual output gating at the source logic. The MC14503BF is a bipolar CMOS-family logic device, with the MC14503B family identified by onsemi as a hex non-inverting, 3-state buffer. The two disable controls divide the six buffers into separately controlled groups: Disable A controls buffers 1 through 4, while Disable B controls buffers 5 through 6. This arrangement permits a compact implementation of segmented shared buses, bidirectional-looking bus translators built from unidirectional channels, and systems that require a driver to relinquish a line during another device's transfer cycle. Typical uses include microprocessor and microcontroller bus isolation, memory-module data buses, peripheral port expansion, test-interface routing, and industrial control systems with shared parallel data paths. The device is particularly relevant when one group of four channels must disengage together while another group of two channels remains active. The package also provides through-hole mechanical compatibility with conventional 16-pin logic-board layouts. For reliable operation, design the disable signals so that no two devices actively drive the same shared node simultaneously. Account for output propagation delay when establishing bus ownership timing, and keep signal routing short enough to limit capacitive loading. Because the device includes a high-impedance state, the disable logic must actively establish every required output state rather than relying on floating control inputs. This product page combines the functional description, technical attributes, sourcing information, interface use cases, and design guidance needed to evaluate the MC14503BF. It also organizes drop-in alternatives and engineering trade-offs so designers can determine whether the original part remains the best fit before modifying a PCB or changing the bus architecture.
MC14510BF - BCD Up/Down Counter | onsemi | Logic IC
The onsemi MC14510BF is a BCD up/down counter integrated circuit, also categorized as a counter and divider, and is offered in a flat-package configuration. Its core function is to count upward or downward through a decade and preserve the count in BCD format, making it suitable for sequencing, timing, and event-counting systems that require decimal-compatible logic rather than ordinary binary counting. The MC14510BF belongs to the broader 4000-series CMOS logic family, where counter ICs operate as state-management building blocks inside larger digital control systems. A BCD up/down counter is a specialized type of counter IC that advances or reverses through ten states from zero through nine. This decimal-oriented behavior can simplify the interface between digital logic and ten-position displays because each decade is represented by four BCD output bits. The counter can therefore support decade-stepping, programmable timing, and sequential control functions. By contrast, a conventional binary counter advances through 16 states per four output bits, which may require additional conversion when a decimal display or decade-oriented mechanism is involved. The MC14510BF uses four parallel BCD outputs to represent the current count. Typical system use requires a clock source, control logic for count direction, reset or initialization handling, and suitable decoupling close to the power terminals. Because the part belongs to the MC14510B family, designers should consult the family datasheet for the exact electrical limits, truth table, propagation timing, supply-voltage range, and pin assignments before finalizing a PCB. MC14510BF is suitable for industrial sequencing equipment, laboratory timers, digital panel meters, test fixtures, event counters, and embedded control subsystems. In a timer or sequencer, the up/down capability allows the same counter to advance through timing intervals or reverse when a control event requests a return to the starting state. In an instrument, the BCD outputs can feed display-driver circuitry without requiring the system controller to perform repeated binary-to-BCD conversion. PCB implementation should follow the package drawing and pin-description table in the onsemi family datasheet. Place the decoupling capacitor close to the supply and ground connections, route clock and control traces away from noisy analog or switching-power nodes, and use a consistent ground-return path. Decoupling requirements, operating voltage, and maximum clock frequency must follow the official family documentation rather than assumptions based on another package or counter variant. This product page combines the device identity, package information, application guidance, comparison structure, and practical design considerations needed to plan a replacement or redesign. It also separates confirmed device facts from parameters that require verification against the manufacturer datasheet, helping engineers create a reproducible design review before committing the counter to a new PCB.
MC14516BD - 3-18V Binary Up/Down Counter | onsemi
The onsemi MC14516BD is a synchronous 4-bit binary up/down counter built with MOS P-channel and N-channel enhancement-mode devices in a monolithic structure. It operates from a 3.0 Vdc to 18 Vdc supply, uses a 16-SOIC package, and includes diode protection on all inputs. The synchronous architecture allows the counting stages to change together rather than operating as separate ripple counters. A binary up/down counter is a digital logic component that increments or decrements a four-bit numerical state according to direction-control and clock inputs. It belongs to the counter and arithmetic-function hierarchy within CMOS logic ICs. The MC14516BD is useful when a digital system must track a sequence in either direction, such as positioning, timing, indexing, or state progression, while retaining the familiar parallel binary-counter interface. Key features include a 3.0 Vdc to 18 Vdc supply range, internal synchronous operation for high-speed counting, and diode protection on every input. These characteristics make the device appropriate for general-purpose digital control, clocked sequencing, and count-direction control. The 16-SOIC package is a surface-mount format that supports conventional reflow assembly and PCB routing without requiring a through-hole footprint. The counter uses MOS P-channel and N-channel enhancement-mode devices in a monolithic implementation. Its internal synchronous operation provides coordinated state transitions when the clock advances the count. Direction control determines whether the binary output increments or decrements, allowing two counting behaviors to share one counter block. The manufacturer describes the circuit as a binary up/down counter and identifies all inputs as protected by diodes. Typical applications include digital position and step tracking, programmable event counters, industrial sequencing logic, instrumentation timers, and control systems that need a reversible binary count. In these systems, the synchronous counter can be clocked from a defined timing source while external control logic selects count direction or clears the state. The broad 3.0 Vdc to 18 Vdc supply range accommodates both low-voltage CMOS logic and higher-voltage industrial interface environments. Designers should use the manufacturer pin-description and connection diagrams when assigning PCB nets and should not infer inactive or reserved pins from abbreviated online descriptions. Input transitions, clock timing, reset behavior, and output-state requirements must be verified against the MC14516BD datasheet before high-speed operation. Decoupling practice should also follow the voltage rails used in the final system and the manufacturer application guidance. This product page consolidates the verified device identity, supply range, synchronous-counter construction, protected-input feature, package information, source links, and same-footprint family alternatives. It also provides application guidance and engineering checks that support faster part selection without replacing the complete manufacturer datasheet.
MC14516BF - 4-Bit Synchronous Up/Down Counter | onsemi
The onsemi MC14516BF is a 4-bit synchronous binary up/down counter built with complementary P-channel and N-channel enhancement-mode MOSFETs in a monolithic structure. It operates from a 3.0 V to 18 V supply, provides input diode protection, and is offered in a 16-pin SOP package. The counter can be incremented or decremented synchronously and can be loaded with a parallel preset value for deterministic control sequences. A synchronous binary counter is a sequential logic device that advances or reverses its four-bit output state on each active clock transition. The MC14516BF belongs to the broader CMOS counter hierarchy, where counter ICs provide repeatable digital state generation for timing, sequencing, arithmetic, and industrial control. Unlike a simple ripple counter, its internally synchronous architecture coordinates state transitions for predictable operation in clocked digital systems. The primary features of the MC14516BF include a 3.0 V to 18 V supply range, internal synchronization, diode protection on all inputs, and four preset inputs. Preset data can be loaded into the counter by applying the desired binary value and asserting the preset-enable control. This combination supports repeatable initialization, programmable step sequences, and compact state management in systems that need more flexibility than a fixed modulus counter. Internally, the monolithic construction combines P-channel and N-channel enhancement-mode MOSFETs. The four output bits represent the current count, while separate direction, clock, preset-enable, and preset-data controls allow the system designer to choose between counting and parallel loading. Because the device operates from 3.0 V through 18 V, it can be used with both low-voltage digital systems and higher-voltage industrial control environments, subject to the input and output limits in the manufacturer datasheet. Typical applications include industrial sequence controllers, programmable timing modules, digital instrumentation, batch-counting equipment, and control systems that periodically divide an event stream into groups. The counter is also useful in laboratory and test equipment where a repeatable four-bit state must advance at each clock edge. A design can use the outputs as address bits, time-slot indicators, step markers, or binary control signals. For reliable implementation, review the manufacturer pin-description table and the input transition and timing diagrams before assigning logic levels. Account for setup and hold requirements around the clock, direction, and preset controls. Ensure unused inputs are connected to a defined valid state and include reset or preset sequencing in the controller startup routine. The 16-pin SOP footprint also requires an appropriate land pattern and adequate clearance between adjacent copper features. This product page combines the manufacturer function description with practical sourcing, replacement, pinout-location, and circuit-integration guidance. It also distinguishes documented device characteristics from parameters that still require verification against the latest ON Semiconductor datasheet, helping engineers move from selection to schematic capture with fewer component-level questions.
MC14521BD - 24-Stage Frequency Divider | onsemi
onsemi MC14521BD is a 24-stage CMOS frequency divider with a 16-pin SOIC package, capable of dividing an input frequency by up to 2^24, or 16,777,216. Its input circuit supports crystal-oscillator, RC-oscillator, and external-oscillator operating modes. Each successive flip-flop divides the preceding frequency by two, making the device suitable for long-duration timing, pulse-rate division, and low-frequency clock-generation systems. A frequency divider is a counter or logic IC that reduces one clock frequency to a lower, predictable frequency. The MC14521BD belongs to the CMOS counter-and-divider hierarchy, where a chain of bistable stages forms a ripple-style binary frequency reduction network. The 24-stage count provides a much longer division interval than ordinary binary counters, allowing a relatively high-frequency timing reference to produce a slow event rate without a microcontroller or complex divider array. The key features of the MC14521BD include 24 internal flip-flops, three selectable input operating modes, division by two per stage, and a maximum count of 16,777,216. Its 16-lead SOIC package supports conventional surface-mount assembly. The D suffix identifies the particular onsemi device grade, while the MC14521B family datasheet describes the common divider architecture and electrical characteristics used to evaluate the MC14521BD. Internally, the input section can operate as a crystal oscillator, an RC oscillator, or a buffer for an externally supplied oscillator signal. This flexibility allows the circuit designer to establish a self-contained timebase or use a cleaner reference already present elsewhere in the system. Each flip-flop divides the frequency of the preceding stage by two, creating a binary sequence across the divider chain and supporting applications that require long count intervals or periodic pulse generation. Typical uses include low-frequency clock generation, industrial timer modules, laboratory pulse generators, frequency-counting instruments, event-rate reduction, and embedded timing references. In an oscillator arrangement, the device can replace a bank of discrete divider flip-flops. When driven from an external oscillator, the same package provides a compact way to reduce a reference clock to a rate suitable for counters, displays, or slow sequencing circuits. Designers should verify the selected crystal or RC network against the operating conditions in the MC14521B datasheet and confirm that the oscillator starts and remains stable over the intended temperature and supply range. Decoupling should be placed close to the supply pins, unused inputs should be held at defined logic levels, and output timing should be checked for the propagation delay accumulated through 24 stages. The maximum operating frequency and output-drive capability must also be considered in the final timing design. This product page combines the verified divider architecture, package information, application guidance, replacement analysis, and practical design considerations in one engineering-focused reference. It helps designers identify the correct operating mode, understand the binary count limit, and distinguish a genuine same-footprint replacement from a merely similar counter before committing a new PCB revision.
MC14521BF - 24-Stage Binary Frequency Divider | onsemi
onsemi MC14521BF is a 24-stage binary frequency divider and counter IC with a 16-pin PDIP package. Its internal architecture contains 24 flip-flops, each dividing the frequency of the preceding stage by two, allowing the device to count through 2^24 states, or 16,777,216. The input circuit supports three operating modes: crystal oscillator, RC oscillator, and buffered external-oscillator input. A binary frequency divider is a sequential logic device that reduces an input clock frequency by a fixed integer factor. The MC14521B belongs to the counter and multivibrator family of CMOS logic ICs, placing it within the broader semiconductor hierarchy of sequential logic, counters, frequency dividers, and clock-management circuits. Unlike a programmable divider or phase-locked loop, it implements a fixed divide-by-2^24 ratio at its output while retaining a simple external clocking architecture. The principal feature of the MC14521BF is its 24-stage flip-flop chain. Each successive stage operates at one-half the frequency of the preceding stage, enabling a clock input to be divided into a substantially lower-frequency output. The manufacturer describes three input configurations: a crystal oscillator, an RC oscillator, or an input buffer for an externally supplied oscillator. These configurations give designers flexibility when creating stable timing references or dividing an existing system clock. The internal counting architecture advances on each active clock transition. The 24-bit count range reaches 16,777,216, which makes the device useful for long timing intervals, fixed-ratio clock generation, event counting, and low-frequency timing references. Its fixed binary ratio differs from general-purpose programmable counters and makes system timing easier to analyze when a known divide factor is required. Typical uses include timer and delay networks, pulse-rate reduction, instrumentation clocks, sequential test systems, low-frequency waveform generation, and digital timing references. In an RC or crystal-oscillator implementation, the device can establish its own timing source; with the buffered external-oscillator mode, it can instead divide a clock already present elsewhere in the system. Designers should select the appropriate oscillator components and confirm the device’s electrical limits, supply requirements, and timing characteristics against the manufacturer datasheet before implementation. PCB layout should keep oscillator and timing paths compact, maintain a defined ground reference, and separate sensitive timing nodes from noisy switching circuits. The 16-pin PDIP package is suitable for through-hole assembly and prototype or legacy industrial equipment where a large package is acceptable. This page combines the manufacturer function description, package and pin-count information, architecture details, application guidance, and a transparent assessment of drop-in replacement options. It also distinguishes the uniquely ordered MC14521BF ordering code from generic family references and focuses design decisions on the fixed 24-stage division behavior.
MC14543BF - 3-18V BCD 7-Segment LCD Driver | onsemi
The onsemi MC14543BF is a CMOS BCD-to-seven-segment latch, decoder, and driver designed for liquid-crystal readouts, with operation from 3 V to 18 V in a 16-pin SOIC package. It accepts 4-bit BCD input and uses the 8421 code format to control the seven segment and decimal-point outputs required by common LCD display readouts. The MC14543BF combines input storage, code decoding, and display drive functions in one integrated circuit. An LCD BCD-to-seven-segment decoder is a display-interface IC positioned between a digital control system and a segmented liquid-crystal display. In the signal hierarchy, it belongs to the decoder and display-driver class within integrated logic and interface circuits. Its internal latch captures the input code, allowing the connected logic to update a display value without unintended intermediate segment transitions during the storage interval. The MC14543BF operates across a 3 V to 18 V supply range, allowing it to interface with both low-voltage and higher-voltage CMOS systems when its output drive requirements match the selected display. Its CMOS construction supports low-power operation in battery-powered equipment, while the integrated latch and 8421 BCD decoder reduce the number of external components required for a basic numeric display. The 16-pin SOIC package supports conventional surface-mount assembly. Because liquid-crystal segments generally require an alternating drive rather than a static DC level, the MC14543BF is intended for displays with compatible drive characteristics. Its segment outputs should be connected in accordance with the manufacturer pin-description table and the display module's required common and segment arrangement. Designers should verify output timing, polarity, and segment mapping against the selected LCD rather than inferring them only from the segment labels. Typical uses include compact digital meters, panel counters, small industrial readouts, laboratory equipment, and embedded control panels that receive BCD values from a microcontroller, counter, or system controller. It is especially appropriate where a dedicated numeric display is needed and the source already supplies a stable 4-bit BCD word. The latch function can simplify display updates and reduce intermediate visual states. Design the PCB with a low-impedance ground return and route the BCD inputs away from sensitive analog or high-speed switching nodes. Confirm the LCD segment mapping, common-drive topology, logic levels, and supply decoupling on the schematic before fabrication. If the display requires LCD bias generation, backlight control, or multiple digits, those functions generally need additional circuitry. This page combines the verified MC14543BF operating limits, package information, function description, sourcing workflow, and design guidance. It also distinguishes a true pin-to-pin replacement from merely similar seven-segment decoder functions by requiring identical package construction and confirmed electrical and pin compatibility.
MC14555BF - Dual 1-of-4 CMOS Decoder | onsemi
The onsemi MC14555BF is a dual binary-to-1-of-4 decoder/demultiplexer built with complementary MOS enhancement-mode devices, packaged in a 16-pin SOIC. Each decoder section has two select inputs, A and B, an active-low enable input, E, and four mutually exclusive outputs, Q0 through Q3. The selected output switches high while the other three outputs remain low. A nominal 5 V supply and 440 ns propagation delay at a 50 pF load are identified for the device. A decoder or demultiplexer is a combinational logic device that converts a binary selection code into one active output path. The dual architecture provides two independent binary-to-1-of-4 conversion channels in one IC. This hierarchy places the MC14555BF in the CMOS logic family, specifically within decoder and demultiplexer logic ICs used to route control, address, or selection signals. The principal feature is active-high decoding: the selected output goes to the high state, while the three unselected outputs remain low. Two select inputs permit all four output positions to be addressed. An active-low enable input provides a common control function for disabling the decoding network. The complementary MOS construction supports low-power operation and compatibility with conventional CMOS logic systems. The MC14555BF combines two complete decoder/demultiplexer functions in one package, reducing component count in designs that require parallel four-way selection. Its 440 ns propagation delay at a 50 pF load provides useful timing guidance for control paths where propagation delay must remain predictable. The 16-pin SOIC package also supports conventional surface-mount assembly and inspection. Typical uses include four-way control-signal routing, address selection, display or peripheral selection, instrumentation multiplexing, and industrial control logic. Because the device is CMOS and operates from a nominal 5 V supply, it is particularly appropriate for systems using 5 V digital logic levels. The enable input can also support shared bus isolation or synchronized selection in a larger controller. Design with the active-low enable polarity and active-high output polarity clearly in mind. Confirm the voltage ratings, absolute maximum conditions, output drive capability, and timing limits in the onsemi datasheet before finalizing a new design. Place the device so that switching outputs do not unintentionally drive adjacent high-impedance nodes, and validate fanout against every connected load. This product page combines the manufacturer function description, package information, timing indications, application guidance, structured specifications, and engineering design notes to accelerate component evaluation. Request current commercial availability and sourcing terms through the Request a Quote form on this page.
MC14556BD - 1-of-4 CMOS Decoder/Demultiplexer | Motorola
The Motorola MC14556BD is a dual binary to 1-of-4 decoder/demultiplexer built with complementary MOS enhancement-mode devices. It accepts two select inputs, A and B, together with an active-low enable input, E, and routes one of four mutually exclusive outputs, Q0 through Q3, according to the select state. The device operates from 3 V to 18 V, supports operation from -55 °C to 125 °C, and is packaged in a 16-pin SOIC. A decoder/demultiplexer is a logic device that converts binary selection information into one active output path. This makes the MC14556BD useful for control, address decoding, peripheral selection, data routing, and test-point multiplexing. Its four outputs are designed so that only one selected output is active for a valid select combination while the enable input provides an additional gating function. The complementary MOS construction places the device in the 4000-series CMOS logic family. The principal electrical characteristics are a 3 V to 18 V supply range, low-power CMOS operation, and an active-low enable control. The package is a 16-SOIC, also described in listings as SOIC-16 or PDSO16, with a body width of 3.90 mm and a nominal 0.154 inch lead pitch. The operating-temperature range of -55 °C to 125 °C supports industrial and extended-temperature equipment where the additional qualification and sourcing requirements are satisfied. The MC14556BD can decode a two-bit command into one of four mutually exclusive destinations, making it appropriate for selecting one sensor, switching one bank of loads, directing a signal path, or controlling a group of digital peripherals. Because it is a demultiplexer, the enable input can inhibit output activity during reset, initialization, or shared-bus conditions. Designers should account for propagation delay and output transition timing when operating at high system clock rates. For reliable PCB implementation, place the device close to the signals it decodes, route the enable and select nets away from noisy switching nodes, and maintain a common ground reference between the logic device and connected circuitry. Use the manufacturer pin-description and logic diagrams when assigning PCB tracks because the available product documentation does not reproduce a verified pin-by-pin connection table here. This product page combines the device’s verified function, supply range, package, temperature range, and sourcing information with application guidance, comparison parameters, and practical design notes. The result helps engineers identify whether the MC14556BD fits a new decoder/demultiplexer design or whether a different logic function is required.
MC14556BF Dual 1-of-4 Decoder/Demultiplexer | onsemi
The onsemi MC14556BF is a dual binary-to-1-of-4 decoder/demultiplexer built with complementary MOS enhancement-mode devices, supplied in a 16-pin gull-wing surface-mount package. Each decoder section accepts two select inputs, A and B, and uses the four binary combinations to address four mutually exclusive outputs. A shared active-low Enable input controls whether the selected output path is active, making the device useful for address decoding, data routing, chip selection, and control-signal multiplexing. A decoder/demultiplexer is a digital logic IC that translates a binary address into one active output. It belongs to the decoder hierarchy within combinational logic, interface ICs, and broader semiconductor products. In demultiplexer mode, the MC14556BF routes one selected output according to the A and B inputs. The active-low Enable input provides a common gating function, allowing the selected path to be disabled without changing the select state. The verified device information identifies complementary MOS enhancement-mode construction, two select inputs, one active-low Enable input, and four mutually exclusive outputs labeled Q2 and Q3 within the family description. Its specified temperature grade is military, and the package is described as a rectangular gull-wing SOP with 16 terminals. These characteristics place it in applications that require compact binary decoding alongside conventional through-hole-era logic-package compatibility. Typical uses include selecting one of four peripheral sections, decoding a two-bit control address, separating mutually exclusive commands, and directing a shared signal toward one of four destinations. Because the outputs are mutually exclusive, the active output provides a straightforward way to convert a two-bit binary value into a one-of-four selection without implementing individual Boolean gates at the system level. When laying out a board, place the device near the signals it decodes and route each output according to its assigned destination. Maintain a common ground reference with the controlling logic and connected circuits. Treat all unused inputs according to the manufacturer logic truth table, and do not infer active levels or output polarity from the output names alone. Review the pin-description and truth-table sections in the manufacturer datasheet before finalizing PCB nets. This page consolidates the device identity, package information, decoder architecture, sourcing workflow, comparison framework, and practical design considerations. It also distinguishes documented facts from parameters that require direct confirmation from the manufacturer datasheet, helping engineers plan a review of the MC14556BF without relying on incomplete distributor summaries.
MC14568BD - Phase Comparator & Programmable Counter | onsemi
The onsemi MC14568BD is a CMOS phase comparator and programmable counter integrated circuit that combines a phase comparator, a 100 counter, and a programmable divide-by-N 4-bit binary counter in one 16-pin SOIC package. All internal counting functions are positive-edge triggered, and the complementary MOS construction provides the device family’s defining logic implementation. A phase comparator is a logic component that determines the relationship between two signals, commonly returning a comparison state when the signals agree or differ. A counter is a sequential digital circuit that records successive clock events and generates corresponding binary states. By integrating comparison and counting functions, the MC14568BD supports signal-phase monitoring, periodic event counting, and programmable frequency division within one compact device. The MC14568B family provides a programmable divide-by-N function implemented with a 4-bit binary counter. This architecture allows an incoming event sequence to be reduced to a selected division ratio. The integrated 100 counter provides a separate counting path, while the phase-comparator section supports two-input phase relationships. These functions are useful when a system must derive a slower periodic indication, monitor relative signal timing, or combine counting and comparison behavior. Constructed with MOS P-channel and N-channel enhancement-mode devices, the MC14568BD uses complementary CMOS in a monolithic implementation. CMOS logic provides a natural connection to digital systems because its switching behavior supports low static power in suitable operating states and broad integration with TTL-compatible system logic when operating and interface conditions are properly matched. Typical uses include digital timing and sequencing systems, phase-error indication, programmable pulse division, event counting, periodic clock generation, and industrial control logic. The same integrated architecture can simplify designs that would otherwise require a separate comparator and binary counter, reducing component count and keeping the comparison and counting functions within one device. Designers should verify the supply-voltage range, operating-temperature limits, input thresholds, output-drive capability, and timing characteristics in the manufacturer datasheet before implementation. The divide control and clock-source connections must also be configured according to the datasheet logic table so that the intended division ratio is selected without invalid intermediate states. This product page organizes the MC14568BD function, package information, verified lifecycle data, sourcing route, and practical design guidance. It also identifies the base-family MC14568B alternative while clearly distinguishing it from suffix-specific procurement decisions. Engineering review should always confirm the exact package suffix, pinout, operating limits, and logic behavior before approving a substitution.
MC14585BD - 4-Bit CMOS Magnitude Comparator | onsemi
The onsemi MC14585BD is a 4-bit CMOS magnitude comparator in a 16-pin SOIC package. It compares two 4-bit binary words presented at inputs A3–A0 and B3–B0, then indicates whether A is less than, equal to, or greater than B through three active-high outputs. The device also provides three cascading inputs so multiple 4-bit sections can be expanded into wider comparison functions without adding a separate priority encoder or equality logic. A magnitude comparator is a digital logic IC that determines the relative order of two binary numbers. Its outputs encode the mathematical relationships A<B, A=B, and A>B, making the comparator a fundamental building block in arithmetic control, sorting, address decoding, test equipment, and digital control systems. The MC14585BD belongs to the CMOS logic family and uses complementary MOS enhancement-mode devices, providing a direct alternative to TTL implementations when system-level logic is already based on CMOS supply rails. The principal features of the MC14585BD are its eight data inputs, three cascade inputs, three active-high comparison outputs, 4-bit comparison width, and 16-pin SOIC format. The cascade inputs allow a more significant 4-bit section to determine the result when lower-order sections are equal. This architecture supports cascaded comparisons for 8-bit, 12-bit, 16-bit, and larger data paths when the corresponding logic states are properly connected. The MC14585BD is intended for conventional CMOS digital systems in which logic thresholds, supply voltage, noise immunity, and propagation delay must be checked against the actual design operating conditions. Because the available manufacturer datasheet identifies the circuit as a CMOS enhancement-mode implementation but does not expose complete electrical-limit tables in the search excerpt, detailed voltage, current, timing, and temperature ratings remain marked where necessary rather than estimated. Typical uses include binary number ordering, digital test fixtures, arithmetic-controller address selection, industrial control logic, embedded comparison functions, and cascading multi-section comparisons. The active-high A<B, A=B, and A>B outputs can feed counters, multiplexers, control-state machines, display logic, or interrupt and status signals in a larger digital system. PCB layout should preserve short input and output traces, provide a solid ground reference, and decouple the power supply near the device. When cascading comparators, route the cascade outputs from the least-significant section into the most-significant section and confirm timing at the system level. The manufacturer datasheet pin-description table should be used as the authority when assigning tracks and probing the 16-pin footprint. This page organizes the manufacturer function description, pin map, verified package information, qualified drop-in comparisons, application guidance, and practical implementation notes. It is designed to help engineers move quickly from device identification to schematic review and PCB-level design decisions while keeping unresolved electrical details explicit.
MC3302PG - 4-Channel 3-36V Comparator | onsemi
The onsemi MC3302PG is a four-channel, general-purpose comparator designed for single-supply operation across a 3 V to 36 V input range. It provides CMOS and TTL-compatible open-collector outputs, a 1 mA supply current specification, and a response time of 1.3 microseconds. The device is packaged in a 14-pin PDIP package for through-hole industrial, consumer, and automotive electronics assemblies. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The MC3302PG belongs to the comparator hierarchy within analog ICs and interface ICs. Its four independent channels allow a single package to perform multiple threshold, level-detection, low-level-sensing, or memory-interface functions while operating from one supply rail. The primary electrical features are the wide 3 V to 36 V operating range, four general-purpose comparator channels, 1.3 microsecond response time, and 1 mA supply current. CMOS and TTL output compatibility allows the open-collector outputs to interface with a broad range of digital logic. The 14-pin PDIP package also supports conventional through-hole assembly and hand prototyping without requiring a fine-pitch surface-mount footprint. Each comparator section is intended to operate from the same single supply, making the IC suitable for systems where a positive supply rail is available but split bipolar rails are not. Open-collector outputs provide a flexible output architecture, while the common-device package simplifies inventory and reduces the number of discrete comparator components required on a board. The 1.3 microsecond response time is appropriate for threshold monitoring and control functions that do not require sub-microsecond timing. Typical uses include level detection, low-level sensing, memory applications, industrial control inputs, consumer equipment, automotive signal interfaces, and digital threshold crossings. The four-channel arrangement is particularly useful when several sensed voltages must be compared against independent references or when redundant comparator decisions are needed within one package. Designers should account for the open-collector output configuration, including pull-up requirements and pull-up resistor selection. Input common-mode range, output saturation behavior, supply-current variation, and input offset must be checked against the manufacturer datasheet for the exact operating condition. Input leads should be routed away from switching nodes and noisy return paths to prevent false comparator transitions. This product page combines the core MC3302PG electrical characteristics, same-footprint replacement options, application guidance, and practical design notes. It is intended to help engineers identify the correct package, confirm logic compatibility, and plan PCB implementation before requesting a quotation for production sourcing.
MC3459P - Quad NMOS Address Line Driver | Motorola
The Motorola MC3459P is a quad NMOS address line driver, also described as a bipolar bus driver, packaged in a 14-pin DIP. The device contains four address-driver elements, each with a one-bit output, for driving address and control lines in older digital systems. According to the available distributor and datasheet listings, the MC3459P operates from a 5.25 V supply and is categorized as an address driver, bus driver, buffer, driver, receiver, and transceiver. A bus driver is an interface IC that strengthens digital signals so they can reliably travel between circuit boards, processors, memories, and peripheral devices. Within the logic-IC hierarchy, a bus driver sits below interface ICs and above general-purpose buffers. The MC3459P is specifically intended to drive multiple address lines in systems where the source device cannot directly provide the required output current or signal integrity. The main verified characteristics are a four-element architecture, one-bit output per element, a 5.25 V supply designation, bipolar bus-driver construction, and a 14-pin DIP package. The listings also identify the device as a Quad NMOS Address Line Driver. The exact output-current rating, propagation delay, output disable levels, input and output logic levels, operating temperature range, and absolute maximum ratings are not present in the supplied search data and therefore require confirmation from the manufacturer datasheet before release to production. The 14-pin through-hole package makes the MC3459P suitable for legacy computer, industrial-control, instrumentation, and data-acquisition equipment where motherboard-level bus routing and socketed DIP construction remain practical. Its four independent driver elements can be assigned to address or control lines when the system architecture requires buffered digital outputs. Modern designs may instead favor surface-mount bus-driver ICs with documented electrical limits and lifecycle guarantees. Engineers should confirm the pinout, enable-control polarity, and logic thresholds before substitution because the supplied distributor records identify the function and package but do not provide a complete pin table. Power-supply decoupling, unused-input handling, and signal-integrity checks should follow the manufacturer datasheet rather than assumptions based on generic 14-pin bus drivers. This page combines verified distributor descriptions, package information, sourcing records, and qualification data into a structured engineering reference. It also documents the remaining datasheet-dependent parameters and the limited cross-reference evidence so that engineers can distinguish confirmed facts from data requiring validation before procurement or PCB redesign.
MC74ACT32DR2G - 5V Quad 2-Input OR Gate, SOIC-14 | onsemi
The onsemi MC74ACT32DR2G is a quad 2-input OR gate from the ACT (Advanced CMOS TTL-compatible) logic family, supplied in a 14-pin SOIC surface-mount package on tape and reel. The device contains four independent 2-input OR gates in a single silicon die, operates from a single 4.5V to 5.5V VCC supply, and is rated for a maximum propagation delay of approximately 9 ns at 5V with a 50 pF load. An OR gate is a fundamental combinational logic primitive whose output is the logical disjunction of its two inputs: the output goes HIGH whenever at least one input is HIGH. The MC74ACT32DR2G belongs to the ACT subfamily, which provides TTL-compatible input voltage thresholds while retaining CMOS output drive capability. In the broader taxonomy, this part sits under: logic gate -> combinational logic -> standard logic -> digital IC -> semiconductor. The ACT family was specifically developed to ease migration from legacy 74LS/74F TTL designs to CMOS, providing the lower quiescent current of CMOS with input levels that directly interface to 5V TTL outputs. Key specifications include four channels per package, two inputs per channel, one output per channel, 24 mA source/sink output drive capability, and a propagation delay of 9 ns at 5V VCC. The device features TTL-compatible input thresholds (VIH = 2.0 V min, VIL = 0.8 V max), rail-to-rail output swing to VCC and ground, and ESD protection on all pins. Power dissipation is reduced by approximately 50% compared to the equivalent bipolar 74LS32, while drive strength is retained. Architecturally, the ACT32 uses CMOS transistors for both the input stage (TTL-compatible threshold via adjusted NMOS/PMOS ratios) and the output stage (symmetric push-pull drivers capable of 24 mA sink/source). This makes the part suitable for driving moderate capacitive loads, bus interfaces within a backplane, and LED indicators. The four gates share VCC and GND pins (pins 14 and 7 respectively), with each gate using two dedicated input pins and one output pin. Typical applications include address decoding in 5V memory-mapped systems, glue logic between microcontrollers and peripherals, bus arbitration logic, control signal combining in industrial PLC interfaces, and general-purpose logic replacement in legacy TTL designs. The wide operating temperature range of -40C to +85C supports both commercial and industrial environments, while the SOIC-14 package is suitable for hand-soldered prototypes and high-volume SMT assembly lines. When designing with the MC74ACT32DR2G, observe standard high-speed CMOS design practice: place a 0.1 uF decoupling capacitor as close as possible to the VCC pin (pin 14), keep input traces short to minimize noise-induced threshold violations, and avoid driving inputs above VCC. Unused inputs must be tied to VCC or GND - never left floating - to prevent unwanted shoot-through current in the input stage that can increase ICC. The ACT32 is a 5V-only part and will not operate correctly at 3.3V; for 3.3V applications use the 74LVC32 family instead. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, with explicit cross-brand references to TI, Toshiba, and Fairchild equivalents that share the same SOIC-14 footprint.