بەرهەمەکان (720+)

LT1016CN8 - 10ns UltraFast Precision Comparator | Analog Devices
LT1016CN8

LT1016CN8 - 10ns UltraFast Precision Comparator | Analog Devices

The Analog Devices LT1016CN8 is an UltraFast 10ns precision comparator with matched complementary TTL/CMOS outputs, latch capability, and single 5V or ±5V supply operation, housed in an 8-pin PDIP (N8) through-hole package. A comparator is an analog building block within the voltage-comparator family of linear integrated circuits that compares two input voltages and drives its output to a digital high or low state depending on the input polarity. Comparators sit in the signal-chain hierarchy between operational amplifiers and logic devices, providing the level decision that interfaces continuous analog signals into digital logic such as TTL and CMOS. High-speed comparators like the LT1016 additionally act as timing and data-slicing elements in measurement and communication systems. Key features of the LT1016CN8 include an UltraFast 10ns typical propagation delay, direct TTL/CMOS logic interfacing while operating off ±5V or a single 5V supply, tight input offset voltage and high gain for precision applications, and matched complementary outputs that extend design versatility. The output stage provides active drive in both directions, eliminating the external pull-up required by open-collector comparators and improving edge symmetry. Technical advantages of the LT1016 architecture include no minimum input slew rate requirement, which allows slow-moving signals to be compared reliably, no power supply current spiking during output transitions, which reduces supply noise in sensitive circuits, and a LATCH pin that retains input data at the outputs when held high, enabling peak-detection and sampling functions. Quiescent negative supply current is only 3mA, allowing the negative supply pin to be driven from a resistive divider without affecting performance. Typical applications include fast sampling and sample-and-hold front ends, high-speed A/D converter input comparators, pulse and timing discriminators, and logic-level translation between analog front ends and TTL/CMOS systems. The 200ns acquisition time noted in the datasheet sample-and-hold application exceeds many monolithic sample-and-hold capabilities. A key design consideration is supply configuration: the LT1016 delivers full performance from ±5V or single 5V rails, but output logic levels must be verified against the connected logic family, and the latch pin should be tied appropriately when latching is not used. This page synthesizes verified datasheet parameters, pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.

RFQ پەیوەندی
LT685CH - 5.5ns ECL High-Speed Comparator | Analog Devices
LT685CH

LT685CH - 5.5ns ECL High-Speed Comparator | Analog Devices

The Analog Devices LT685CH is an ultrafast high-speed comparator with differential inputs, complementary ECL-compatible outputs, and a typical propagation delay of 5.5 ns, supplied in an 8-pin hermetic ceramic DIP package. Its output current capability is suitable for driving 50 ohm transmission lines, while low input offset and high resolution support precision analog-to-digital signal processing. The device also provides an output latch function and an external hysteresis control pin. A high-speed comparator is a signal-conditioning integrated circuit that compares two input voltages and changes its output state according to their relative polarity. The LT685 belongs to the comparator hierarchy within interface and signal-processing semiconductors. Its differential inputs reduce sensitivity to common-mode noise when the compared signals are balanced, while complementary outputs simplify interfacing with ECL-family logic and systems requiring both true and inverted decisions. The LT685CH emphasizes decision speed rather than rail-to-rail input operation or low power consumption. According to the manufacturer product information, the device is fully compatible with ECL logic levels and can adequately drive transmission lines terminated in 50 ohms. The 5.5 ns typical delay is the principal performance figure for high-speed threshold detection. A dedicated latch function allows a decision to be held for downstream circuitry, and external hysteresis control helps designers set or tune the switching threshold behavior. Typical signal paths place the differential inputs close to the source and route them as a short, geometry-matched pair. Because the LT685CH is capable of high-speed output transitions, trace capacitance, impedance discontinuities, and ground-return paths can materially affect observed system performance. Terminated transmission lines should use the intended 50 ohm environment rather than long unterminated traces. The complementary ECL outputs also require careful common-grounding and interface compatibility with the receiving logic. The LT685CH is suited to analog-to-digital signal processing, pulse-width or timing measurements, threshold detection, waveform conditioning, and high-speed instrumentation. Its speed makes it useful when the decision result must arrive quickly, but circuit timing must include comparator delay, external hysteresis, interconnect delay, and receiving-device delay. The CH order suffix is treated as the specific packaged LT685CH variant; package dimensions, pin mapping, and full electrical limits require confirmation from the applicable manufacturer documentation. For PCB design, keep the input pair short, matched, and away from unrelated switching nodes. Place termination close to the driven output, provide a continuous ground reference, and avoid unnecessary stubs. If the output drives a cable or long trace, verify voltage levels and impedance before connecting to ECL inputs. Account for the latch and hysteresis controls during timing analysis rather than treating them as unused pins. This page consolidates the verified LT685 family description, available distributor references, package and lifecycle observations, and engineering guidance into one design-oriented resource. Because the supplied data does not expose a complete manufacturer parameter table or verified direct replacements, unverified electrical values and non-drop-in alternatives are explicitly not inferred.

RFQ پەیوەندی
LT685CN - 5.5ns High-Speed ECL Comparator | Analog Devices
LT685CN

LT685CN - 5.5ns High-Speed ECL Comparator | Analog Devices

The Analog Devices LT685CN is an ultrafast high-speed comparator with a typical propagation delay of 5.5 ns, differential inputs, complementary ECL-compatible outputs, and a 16-pin PDIP package. It is designed for demanding analog-to-digital signal-processing and pulse-timing systems where fast decision time and direct transmission-line drive are important. The device also includes an output latch and an external hysteresis-control function. A comparator is an analog signal-processing semiconductor that evaluates two input voltages and produces a logic output indicating which input is higher. The LT685 belongs to the comparator hierarchy, where its differential inputs, complementary outputs, and ECL interface place it between general-purpose logic-level comparators and high-speed timing components used in instrumentation, communications, and data acquisition. The main features of the LT685CN include its 5.5 ns typical propagation delay, complementary ECL outputs, 50-ohm transmission-line drive capability, low input offset, output latch capability, and compatibility with the AM685 family. Its differential input structure supports balanced signal comparison, while the complementary outputs allow direct use in systems requiring both true and inverted decisions. The latch function can hold the comparator state for applications that need sampled or stored decisions rather than continuous tracking. The LT685 uses an older high-speed ECL-compatible architecture intended for short propagation-delay operation and controlled point-to-point interconnects. Its output current capability is specified for driving transmission lines terminated in 50 ohms, making board-level routing and termination more important than with ordinary CMOS or TTL comparators. Differential inputs can also reduce sensitivity to common-mode noise when the surrounding analog signal path is properly laid out and referenced. Typical applications include pulse-width and pulse-height discrimination, high-speed threshold detection, ECL interface circuits, analog-to-digital front ends, communications equipment, laboratory instrumentation, and timing recovery systems. The 16-pin PDIP package is through-hole and suitable for legacy or prototype boards where the comparator must be inserted or socketed rather than mounted in a compact surface-mount assembly. When designing a circuit around the LT685CN, verify input common-mode range, output termination, supply requirements, latch timing, and the required propagation-delay margin. Keep high-speed traces short, use controlled impedance where practical, and terminate ECL-compatible outputs according to the system’s transmission-line topology. The available verified data does not establish exact input common-mode limits, supply-current values, pin-level timing, or package temperature limits. This product record combines the verified LT685 and LT685CN manufacturer information, distributor availability references, and cross-reference search results with practical guidance for high-speed comparator implementation. It also distinguishes documented drop-in alternatives from package or functional similarities so that engineers can make a replacement decision based on actual pin and parameter evidence.

RFQ پەیوەندی
LTC1380IGN#PBF - 8-Ch SMBus Analog Mux, 70Ohm | Analog Devices
LTC1380IGN#PBF

LTC1380IGN#PBF - 8-Ch SMBus Analog Mux, 70Ohm | Analog Devices

The Analog Devices LTC1380IGN#PBF is a CMOS single-ended 8-channel analog multiplexer with an SMBus-compatible two-wire digital interface, featuring 70 ohm on-resistance, 10 uA supply current, and a wide 2.7 V to +/-5 V supply range, housed in a 16-pin SSOP (SSOP-16) package. An analog multiplexer (mux) is a switching IC that selects one of several analog input signals and routes it to a single output under digital control, making it a foundational block in the signal-switching hierarchy: multiplexer switch IC -> analog switch -> data conversion front end -> signal chain. Unlike electromechanical relays, CMOS muxes such as the LTC1380 switch in microseconds, consume microamp-level power, and integrate the decode logic on-chip. Key differentiating features include the SMBus-compatible serial interface that requires only two wires (SCL and SDA), four hard-wired SMBus addresses selectable with two external address pins, and the Pb-free (RoHS) SSOP-16 package indicated by the #PBF suffix. The extremely low 10 uA supply current makes the part well suited to battery-powered and remotely powered data-acquisition systems. Architecturally, the LTC1380 uses CMOS transmission-gate switches driven by an on-chip decode stage controlled by the serial port. Break-before-make switching prevents momentary shorting of selected channels, and the 70 ohm on-resistance keeps insertion loss low in moderate-impedance signal paths. The wide 2.7 V to +/-5 V supply capability supports both single-supply 3 V/5 V logic systems and dual-supply analog domains for bipolar signals. Typical applications include industrial data-acquisition front ends, battery-powered sensor monitoring, automatic test equipment channel routing, and general-purpose analog signal selection in embedded systems with an SMBus or I2C-compatible controller. Design-wise, keep the off-channels' source impedance low and add an op-amp buffer after the mux output if the downstream load is capacitive or high-value, because the 70 ohm RON combines with load current to create gain error. This page synthesizes distributor pricing context, drop-in alternatives, pin/package guidance, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
LTC6993CS6-4 - TimerBlox Monostable Pulse Generator (One-Shot) | ADI
LTC6993CS6-4

LTC6993CS6-4 - TimerBlox Monostable Pulse Generator (One-Shot) | ADI

The Analog Devices LTC6993CS6-4 is a monostable multivibrator (one-shot pulse generator) from the TimerBlox family of silicon timing devices, offered in a 6-pin TSOT-23 package with programmable pulse width from 1 µs to 33.6 seconds set by a single external resistor RSET. The part accepts a wide 2.25 V to 5.5 V supply, delivers up to ±20 mA output drive, and exhibits a worst-case trigger-to-output propagation delay of approximately 11 ns, making it one of the fastest precision one-shots in this package class. The S6-4 variant is the retriggerable sub-version: while the output is HIGH, additional rising trigger edges restart the timing interval, allowing the pulse width to be extended indefinitely for missing-pulse detection or watch-dog timeout applications. A monostable multivibrator (also called a one-shot) is a sequential logic block that, on receipt of a single trigger event, produces one output pulse of a defined width and then returns to its stable idle state. Within the broader digital-timing hierarchy, a one-shot sits alongside astable oscillators, counters, and delay lines as a fundamental timing primitive used to convert edges into precisely controlled pulses. The TimerBlox family positions the LTC6993 between simple RC one-shots (poor accuracy) and full microcontroller timer peripherals (high overhead): it provides digital-grade accuracy over a 33,600:1 timing range with no firmware, no crystal, and only one external resistor. Key features of the LTC6993CS6-4 include a master oscillator accuracy of ±1.5% over voltage and temperature, an internal counter that divides the master frequency by N = 4/64/128/256/512/1024/2048/4096, retrigger capability, a separate rising-edge trigger input, and CMOS-compatible output drive. The device is specified over the commercial 0 °C to 70 °C range; an industrial-grade sibling (LTC6993IS6-4) covers -40 °C to 85 °C. Because the output pulse is generated by digital division of a trimmed master oscillator, pulse-to-pulse jitter is dominated by trigger jitter rather than RC drift, giving far cleaner results than discrete 555-based one-shots. Typical applications include missing-pulse detection in safety and sensor monitoring, watchdog timer reset generation, frequency-to-pulse conversion, switch de-bouncing, time-of-flight laser or ultrasonic ranging front-ends, and pulse-stretching for narrow event capture. In each case the LTC6993 replaces either a 555 timer (better accuracy, smaller BOM) or a microcontroller capture/compare channel (faster response, no firmware burden). When designing with this part, select RSET to place the master oscillator in the range that, after the chosen divider N, yields the desired output pulse width; keep the trigger pulse width shorter than the programmed output pulse to guarantee clean retriggering; and place a 0.1 µF decoupling capacitor within 2 mm of the V+ pin to prevent supply transients from disturbing the internal oscillator. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
LTC6993HS6-4 - Mono Pulse Gen One-Shot 1µs-33.6s | ADI
LTC6993HS6-4

LTC6993HS6-4 - Mono Pulse Gen One-Shot 1µs-33.6s | ADI

The Analog Devices LTC6993HS6-4 is a monostable multivibrator (one-shot pulse generator) with a programmable pulse width of 1µs to 33.6 seconds, housed in a 6-pin TSOT-23 (S6) package. It belongs to the TimerBlox family of silicon timing devices and provides an 11 ns typical propagation delay. The LTC6993HS6-4 operates from 2.25 V to 5.5 V supply and covers the -40°C to 125°C automotive temperature grade. A monostable multivibrator (also known as a one-shot pulse generator) is a sequential logic element that produces a single output pulse of fixed duration in response to a trigger edge, then returns to its stable state until the next trigger. One-shots sit within the broader category of timer ICs and are widely used for pulse stretching, edge-to-level conversion, missing-pulse detection, and digital debouncing. Because timing accuracy is achieved via a single external resistor (RSET) and the part is fully self-contained, one-shots are easier to design with than discrete RC or 555-based equivalents. Key features of the LTC6993HS6-4 include a wide programmable pulse-width range (1µs to 33.6s) set by RSET, a low 11 ns propagation delay, 2.25 V to 5.5 V single-supply operation, and CMOS-compatible logic inputs/outputs. The device also includes an internal master oscillator derived from RSET, allowing the output pulse duration to be calculated via tOUT = N_DIV × RSET / 50 kΩ × (typical 1.0), enabling precise digital control of pulse width without external capacitors. The architecture uses a precision current reference feeding an internal master oscillator whose frequency is set by RSET; the resulting clock is divided by a fixed N factor to produce the output pulse. An on-chip comparator triggers on the rising edge of the input, with retrigger capability and an optional reset pin on related family members. This analog-digital hybrid approach yields excellent supply-rejection and temperature stability compared to simple 555 timer designs. Typical applications include industrial control pulse generation, automotive system timing, watchdog/missing-pulse detectors, debouncing mechanical switches, frequency discriminator circuits, and low-frequency clock generation in test equipment. The wide 1µs to 33.6s range covers most pulse-stretching needs from high-speed digital logic to multi-second industrial timing. The AEC-Q100 grade (H temp range) makes it suitable for automotive applications. When designing with the LTC6993HS6-4, select RSET between 10 kΩ and 1 MΩ using a low-drift, low-leakage resistor for accuracy, and place it close to the RSET pin to minimize noise pickup. Verify input pulse width is shorter than the programmed output pulse to ensure proper retrigger behavior. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.

RFQ پەیوەندی
LTC6993IS6-2 - TimerBlox One-Shot Pulse Generator | ADI
LTC6993IS6-2

LTC6993IS6-2 - TimerBlox One-Shot Pulse Generator | ADI

The Analog Devices LTC6993IS6-2 is a programmable monostable multivibrator (one-shot pulse generator) from the TimerBlox family, delivering a single output pulse whose width is set by a single external resistor RSET. The device integrates fully into a TSOT-23-6 package and provides a pulse width range of 1 µs to 33.6 seconds with a typical propagation delay of only 11 ns. The "-2" sub-version is retriggerable, allowing the output pulse to be extended by additional trigger events received while the output is still active. A monostable multivibrator (also known as a one-shot) is a sequential logic block that, upon receiving a single trigger edge, produces one output pulse of defined width and then returns to its stable (idle) state. It belongs to the broader family of multivibrators (a family that also includes astable/oscillator circuits and bistable/flip-flop circuits) and is widely used in digital control, instrumentation, and signal-conditioning subsystems. The LTC6993 family sits within Analog Devices' TimerBlox silicon timing platform, which also covers oscillators (LTC6905), low-frequency clocks (LTC6930), and divider/edge-delay blocks. Key features of the LTC6993IS6-2 include a 2.25 V to 5.5 V supply range, CMOS-compatible inputs, push-pull output stage capable of sourcing/sinking 20 mA, programmable pulse width via a single resistor to ground, retriggerable behavior (sub-version -2), and an extremely low quiescent current of typically 65 µA. The internal master oscillator is factory-trimmed, eliminating the need for external timing capacitors or trim potentiometers. The DIV pin provides four discrete range selections (1 µs, 1 ms, 1 s, 33.6 s) that scale the RSET current. Typical applications include watchdog timer reset generators, fault-pulse stretchers, switched-mode power supply synchronization, debounce timers for mechanical switches, and pulse-width extension in instrumentation front-ends. In battery-powered designs, the low quiescent current makes it suitable for always-on timing functions. When laying out a board, place RSET close to the SET pin to minimize leakage paths and use a clean ground pour under the part to keep the analog timing reference stable.

RFQ پەیوەندی
LTC6993MPS6-4#TRMPBF - 33.6s Monostable TimerBlox One-Shot | Analog Devices
LTC6993MPS6-4#TRMPBF

LTC6993MPS6-4#TRMPBF - 33.6s Monostable TimerBlox One-Shot | Analog Devices

The Analog Devices LTC6993MPS6-4#TRMPBF is a monostable multivibrator (one-shot pulse generator) with a programmable pulse width of 1 microsecond to 33.6 seconds, housed in a 6-pin TSOT-23 (S6) package. It belongs to the TimerBlox family of versatile silicon timing devices and the -4 variant is falling-edge sensitive and retriggerable, allowing the output pulse to be extended by additional trigger signals received while the output is active. The part operates from a 2.25 V to 5.5 V supply and is specified over the military -55C to +125C temperature range (MP grade). A monostable multivibrator, commonly called a one-shot, is a sequential logic element that produces a single output pulse of fixed duration in response to a trigger input. It belongs to the broader category of multivibrator circuits within digital logic ICs, which also includes astable (free-running) and bistable (flip-flop) variants. The LTC6993's TimerBlox architecture replaces legacy 555-timer-style discrete designs with a precision silicon solution offering tighter tolerance, lower power, and smaller PCB area, while maintaining the familiar single-resistor programming interface. Key features include an 11 ns propagation delay, internal master oscillator set by a single external resistor (RSET), CMOS logic outputs, and a separate divider setting (NAD pin) that selects one of eight pulse-width ranges. The retriggerable -4 variant ignores the rising edge and starts the timing cycle on a falling transition at the trigger input, making it well suited for debounce, missing-pulse detection, and watchdog reset circuits where the pulse must be restarted if a new event occurs before completion. Architecturally, the LTC6993 uses a programmable current source feeding an internal master oscillator whose frequency is set by RSET to a known reference. A divider chain produces eight selectable time bases from 1 microsecond up to 33.6 seconds, and the trigger logic arms the output pulse for one full timing cycle. Output rise and fall times are typically a few nanoseconds, and supply current is approximately 100 to 400 microamps depending on programmed pulse width and output state. Typical applications include watchdog timers, missing-pulse detectors, switch debouncers, frequency discriminators, one-shot pulse generators, and precision delay lines in industrial control, automotive, and instrumentation systems. In these roles, the LTC6993MPS6-4#TRMPBF delivers reliable timing with single-resistor programming, eliminating the need for external capacitors or trim potentiometers. When designing with this device, select RSET between 50 kohm and 800 kohm to set the master oscillator, then choose the appropriate NAD setting to land the desired pulse width within the 1 microsecond to 33.6 second range. Always place a 0.1 microfarad decoupling capacitor close to the V+ pin, and ensure the trigger pulse width is shorter than the programmed output pulse to allow retriggering.

RFQ پەیوەندی
M4T28-BR12SH1 - 48mAh SNAPHAT Lithium Battery + 32.768 kHz Crystal | STMicroelectronics
M4T28-BR12SH1

M4T28-BR12SH1 - 48mAh SNAPHAT Lithium Battery + 32.768 kHz Crystal | STMicroelectronics

The STMicroelectronics M4T28-BR12SH1 is a SNAPHAT® top battery-and-crystal module that delivers 48 mAh of lithium backup capacity at 2.8 V with an integrated 32.768 kHz quartz crystal (12.5 pF load), purpose-built as the detachable power source for ST's TIMEKEEPER® series of serial real-time clocks and non-volatile SRAM/Supervisor ICs housed in 28- and 44-pin surface-mount SOIC packages. The SNAPHAT design lets the lithium cell and crystal be snapped onto an SOIC base after reflow, keeping the battery off the board during high-temperature assembly and giving the end product years of battery-backed RTC retention. A lithium coin-cell backup battery is a primary (non-rechargeable) lithium cell that keeps volatile memory and real-time clock registers alive when the system main rail collapses; for non-volatile SRAM supervisors and RTCs it sits in the same supply hierarchy as a coin cell, a supercap-backed supply, and a buck/boost hold-up rail. In the TIMEKEEPER family the SNAPHAT module also carries the 32.768 kHz tuning-fork crystal so that the combined Battery+Crystal pair forms a complete timekeeping sub-assembly — the IC underneath just exposes a top-of-package cavity that the SNAPHAT clips into. Key features include a 48 mAh nominal capacity with lithium chemistry (long-shelf-life primary cell), an integrated 32.768 kHz crystal specified for 12.5 pF load capacitance, a typical operating voltage of 2.8 V and a detachable SNAPHAT housing that allows board-level assembly of the SOIC base before the lithium part is added. ST publishes a multi-year backup time figure and an estimated self-discharge shelf life at +25 °C so the engineer can size RTC retention against product life. Inside the SNAPHAT housing, the lithium coin cell is connected through the SOIC pinout's Vbat/RET pins while the crystal ties to the RTC's oscillator pins; the SNAPHAT body itself provides the mechanical alignment and the battery contact springs. Because the same SNAPHAT accepts both M4T28-BR12SH1 and M4T32-BR12SH1 variants, the top is reusable across ST's 28- and 44-pin TIMEKEEPERS with no board change. Typical applications are RTC + NVRAM backup in industrial controllers, point-of-sale terminals, metering and data-logging equipment, medical instruments needing tamper-proof time, and any system where the lithium cell must be replaced without re-flowing the base SOIC IC. The M4T28-BR12SH1 is the matching SNAPHAT for the M48T201, M48T58, M48T35 and M48T08/18 TIMEKEEPER family. Design consideration: do not expose the SNAPHAT to reflow temperatures above +220 °C — it must be snapped on only after the SOIC base has been soldered. Storage below +30 °C and low humidity extends shelf life, and polarity on the SNAPHAT must match the SOIC base markings to avoid reverse-charging the lithium cell. This page consolidates distributor pricing, exact SNAPHAT specifications, drop-in alternatives from the M4Txx-BR12SH family, and design guidance that supplements the STMicroelectronics datasheet — synthesized for engineers who must select, source, and qualify a TIMEKEEPER battery+crystal module quickly.

RFQ پەیوەندی
M74HC14 - Hex Schmitt Inverter, 6-Channel, CMOS | STMicroelectronics
M74HC14

M74HC14 - Hex Schmitt Inverter, 6-Channel, CMOS | STMicroelectronics

The STMicroelectronics M74HC14 is a high-speed CMOS hex Schmitt trigger inverter fabricated with silicon-gate C2MOS technology, packaged in 14-pin SOIC, providing six independent inverting buffers with 20% VCC input hysteresis. Each channel delivers a typical propagation delay of 12 ns at VCC = 6 V, balanced symmetrical output impedance with |IOH| = |IOL| = 4 mA minimum drive, and typical quiescent supply current ICC well under LSTTL equivalents while maintaining pin-to-pin compatibility with the M74HC04 non-Schmitt hex inverter. A Schmitt trigger inverter is a digital logic building block that converts a slowly-changing or noisy input waveform into a clean, sharply-transitioning output by using two different switching thresholds: VT+ for the low-to-high transition and VT- for the high-to-low transition. The voltage gap between these thresholds is called hysteresis. Compared with a standard CMOS inverter, a Schmitt trigger is far more tolerant of noisy, slowly-rising, or analog-style input signals, which makes it the standard choice for line receivers, RC oscillators, debounce circuits, and waveform shapers. Within the broader taxonomy, the M74HC14 sits inside the 74HC logic family, which itself belongs to CMOS logic ICs and the wider semiconductor category. Key features include a wide operating voltage range from 2 V to 6 V, 1.2 V typical noise immunity at VCC = 6 V, balanced propagation delays tPLH/tPHL, ESD protection on all inputs, and CMOS-compatible low quiescent current. The Schmitt hysteresis is specified as 20% of VCC, which scales automatically across the supply range, giving reliable switching margins in 3.3 V and 5 V rails alike. The device is built using silicon-gate C2MOS technology, which combines the high-speed LSTTL-class switching performance of bipolar TTL with the low static power consumption inherent to CMOS. Internal diode clamps protect inputs against ESD and latch-up, while the symmetrical output stage provides equal source and sink drive strength so edges remain matched under capacitive loading. Typical applications include waveform shaping and line receivers in industrial control, debounce circuits for mechanical switches and keypads, RC relaxation oscillators for clock generation, monostable and astable multivibrators, and signal conditioning between noisy sensors and downstream logic. Its six channels are common in PCB digital designs for handshake-overs signal lines, sensors, or power-management blocks. When using M74HC14 in oscillator or debounce circuits, choose leakage and hysteresis parameters to balance timing accuracy against power consumption. Input rise/fall times must remain slower than the internal hysteresis response or pulse stretching will distort the output duty cycle. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
M74HCT244B1 - Octal 3-State Bus Buffer, HCT, DIP-20 | STMicroelectronics
M74HCT244B1

M74HCT244B1 - Octal 3-State Bus Buffer, HCT, DIP-20 | STMicroelectronics

The STMicroelectronics M74HCT244B1 is an octal bus buffer with 3-state outputs, fabricated in advanced silicon-gate C2MOS technology and housed in a 20-pin DIP (B1 suffix) through-hole package. The device features two active-low output enable inputs (1OE and 2OE), each governing four bus buffers, with non-inverting data flow from A to Y on each channel. An HCT logic interface — 74HCT — is a high-speed CMOS logic family with TTL-compatible input voltage thresholds (VIH = 2.0 V min, VIL = 0.8 V max) that allows direct interfacing with bipolar TTL outputs while preserving the low power consumption of CMOS. Within the broader taxonomy, the M74HCT244B1 belongs to the buffer/driver category of standard logic ICs (74-series logic > buffer/driver ICs > interface ICs > integrated circuits). This HCT sub-family operates from a single 4.5 V to 5.5 V supply, making it the standard logic choice for 5 V digital systems that must bridge CMOS controllers with legacy TTL peripherals. Key features include a typical propagation delay of 12 ns at VdM8 = 5 V, low quiescent supply current (ICC of 4 µA max per channel), 6 mA standard output drive, and ±20 mA balanced output drive capability at 5 V. All inputs include protection circuits against static discharge and transient excess voltage, and the device is specified over the commercial 0 °C to +70 °C operating temperature range (B1 suffix), with a -40 °C to +85 °C industrial variant (B1R suffix) also available from STMicroelectronics. The C2MOS silicon-gate process yields low power dissipation (ICC quiescent of 80 µA max for the whole IC) while delivering CMOS-equivalent speed. Typical applications include memory and address bus buffering in microprocessor systems, peripheral interface drivers for 5 V logic, LED display driving, and general-purpose bus isolation in industrial control and instrumentation. Two active-low output enables let designers independently disable the upper and lower nibbles, which is convenient for 8-bit bus demultiplexing or for tri-state bus sharing among multiple masters. When designing with this part, place a 0.1 µF decoupling capacitor as close as possible to VCC pin 20 to suppress switching transients, and ensure both 1OE and 2OE are tied high through pull-ups if always-enabled operation is desired. The DIP-20 footprint remains popular for through-hole prototyping and legacy board retrofits, while the surface-mount M74HCT244M1R (SO-20) variant serves modern SMT designs. This page synthesizes STMicroelectronics datasheet parameters, distributor pricing, drop-in 74HCT244 equivalents from ST/TI/onsemi/NXP, and practical design notes not bundled in a single distributor listing.

RFQ پەیوەندی
M74HCT273B1R - 8-Bit D-Type Flip-Flop with Clear, DIP-20 | STMicroelectronics
M74HCT273B1R

M74HCT273B1R - 8-Bit D-Type Flip-Flop with Clear, DIP-20 | STMicroelectronics

The STMicroelectronics M74HCT273B1R is an octal D-type flip-flop with master reset (clear), eight positive-edge-triggered D-type storage latches, and TTL-compatible HCT-series CMOS inputs, housed in a 20-pin PDIP (0.300 inch / 7.62 mm) through-hole package. It is specified for a 4.5 V to 5.5 V supply range, delivers a typical maximum clock frequency of 80 MHz at VCC = 4.5 V, and provides non-inverted (true) Q outputs with a maximum propagation delay of 30 ns. An octal D-type flip-flop is a synchronous digital storage element which captures logic levels on eight parallel D inputs at the rising edge of a common clock and holds them on eight Q outputs. The 74HCT family combines low-power high-speed CMOS logic with TTL-compatible input thresholds (VIH = 2.0 V minimum), allowing direct interface with 5 V TTL buses without level shifters. The M74HCT273B1R sits in the digital logic IC hierarchy as: flip-flop -> sequential logic -> logic IC -> integrated circuit -> discrete semiconductor category. Its single-bit-wide clocked register function makes it a foundational building block in bus-oriented digital systems. Key features include a common clock and common master reset (active-low CLR) shared by all eight latches, non-inverted Q outputs, complementary CMOS output drive, low quiescent current of 4 uA, and broad compatibility with 74LS273 and 74HCT273 logic families from multiple vendors. The 20-pin PDIP package retains through-hole compatibility with legacy breadboard and socketed designs, while the HCT input stage directly accepts bipolar TTL drive levels. Technically, the device uses high-performance silicon-gate CMOS to deliver fMAX = 80 MHz (typical) at 4.5 V supply with tPLH around 13 ns and tPHL around 17 ns, all while drawing only a few microamperes of quiescent current. The master reset overrides the clock and asynchronously forces all Q outputs low when driven low. Typical applications include address and data latching in microcontroller expansion logic, I/O port expansion with 74HC595-style shift chains (this part is parallel-load, not serial-shift), debounced pushbutton and rotary-synchronous address, and general-purpose register buffering in TTL-based industrial control and instrumentation systems. When designing with this part, ensure the CLR pin is tied high through a pull-up resistor if asynchronous reset is not used, and provide standard 0.1 uF decoupling close to VCC to maintain noise margin in mixed-signal environments. This page synthesizes distributor pricing, drop-in alternatives, and design guidance beyond the manufacturer datasheet alone.

RFQ پەیوەندی
M74VHC1GT50DFT1G - Single Non-Inverting Buffer/Level Shifter | onsemi
M74VHC1GT50DFT1G

M74VHC1GT50DFT1G - Single Non-Inverting Buffer/Level Shifter | onsemi

The onsemi M74VHC1GT50DFT1G is a single-gate non-inverting CMOS buffer with TTL-compatible inputs, designed as a logic level shifter between low-voltage TTL signals and a higher-voltage CMOS rail. Housed in a 5-pin SC-88A (TSOP-5/SC-70-5/SOT-353) surface-mount package, the part operates from a 1.65 V to 5.5 V VCC supply, delivers a typical propagation delay of 3.5 ns at 5 V, and draws only 1 µA maximum quiescent current at 25 °C. What is a non-inverting buffer / level shifter? It is a single-bit logic device that regenerates an input signal to a full-rail output without inverting its polarity. When TTL logic swings (0.8 V/2.0 V thresholds) must drive a higher-voltage CMOS rail (3.3 V or 5 V), a TTL-to-CMOS level shifter buffer is required; the device sits in the signal chain between an upstream controller and a downstream CMOS load, restoring logic levels and providing isolation. This hierarchy places it under: buffer → line driver → logic IC → integrated circuit → semiconductor. Key features include TTL-compatible input thresholds (VIL = 0.8 V, VIH = 2.0 V when VCC = 5 V), CMOS-compatible outputs (VOH > 0.8·VCC, VOL < 0.1·VCC at rated load), 5 V tolerant inputs with power-down protection on both inputs and outputs, and balanced propagation delays. The part is fabricated with silicon-gate CMOS technology that achieves bipolar-Schottky-TTL-like speed while maintaining CMOS-level quiescent dissipation. The SC-88A/TSOP-5 footprint occupies only ~2.0 mm × 2.1 mm of board area. Typical applications include interfacing 5 V TTL peripherals to 3.3 V or 2.5 V CMOS logic domains, signal conditioning in mixed-voltage microcontroller designs, and clock or single-line data buffering in portable, industrial, and consumer systems. Designers select this part when board space is constrained and a true single-gate buffer is required without the overhead of multi-channel drivers. A primary design consideration is input-edge speed: although the device accepts slow TTL edges, the output rise/fall time depends on the load capacitance and VCC. Decouple VCC with a 0.1 µF ceramic capacitor placed as close as possible to pin 5, and avoid driving large capacitive loads without a series damping resistor. This page synthesizes distributor pricing, drop-in same-package alternatives from onsemi and competing vendors, and practical design notes that go beyond the manufacturer datasheet summary.

RFQ پەیوەندی
MAX301CSE+ - Dual SPST 35Ω Analog Switch | Analog Devices
MAX301CSE+

MAX301CSE+ - Dual SPST 35Ω Analog Switch | Analog Devices

The Analog Devices (Maxim Integrated) MAX301CSE+ is a precision, dual, high-speed analog switch containing two independent single-pole single-throw (SPST) normally-open (NO) switch channels in a 16-pin SOIC package. Each channel offers a maximum on-resistance of 35 ohms, guaranteed to match within 2 ohms between channels, making it suitable for precision signal routing where channel-to-channel consistency matters. A precision analog switch is a type of bidirectional signal gate within the broader family of analog switches and multiplexers (signal routing ICs within data converters and interface signal chains). Unlike a relay, a solid-state CMOS analog switch switches microsecond-fast with no moving parts, and unlike a digital logic gate, it passes continuous analog signals in both directions with minimal distortion. Switches sit between multiplexers (many channels to one) and simple gates, and are fundamental building blocks of signal conditioning, test, and communication systems. Key features of the MAX301 include low on-resistance (less than 35 ohms guaranteed), channel matching within 2 ohms for gain-consistent switching, high-speed switching for fast signal paths, and a dual-channel SPST NO configuration that lets two independent signals share one IC. The '+' suffix denotes Analog Devices' enhanced (lead-free, RoHS-compliant) manufacturing flow. Architecturally, the MAX301 family uses CMOS switch technology with logic-controlled gate drive, providing flat on-resistance across the analog signal range and low charge injection. The normally-open configuration ensures signals are isolated by default and only connected when the control logic commands it, which is the safe default for test equipment, redundant signal paths, and fault-tolerant routing. Typical applications include audio and video signal routing, precision test and measurement switching matrices, communication-system signal gating, data-acquisition channel isolation, and industrial control signal selection. The dual-channel layout is efficient for stereo signal pairs, differential-pair gating, and redundant-path designs where two switches switch simultaneously or independently. When designing with the MAX301CSE+, keep switch on-resistance in mind when driving low-impedance loads, since 35 ohms in series can introduce gain error in precision dividers. Consult the manufacturer datasheet for supply-voltage ranges, switching-time specifications, and control-logic thresholds before finalizing the design. This page synthesizes distributor availability listings, family cross-reference information, and practical design notes not found in a single manufacturer document, making it a one-stop engineering reference for the MAX301CSE+.

RFQ پەیوەندی
MAX368CPN+ - 8:1 Fault-Protected Analog Mux, 1.8kOhm | Maxim
MAX368CPN+

MAX368CPN+ - 8:1 Fault-Protected Analog Mux, 1.8kOhm | Maxim

The Analog Devices (Maxim Integrated) MAX368CPN+ is a fault-protected 8-channel (8:1) analog multiplexer with internal data latches and a 1.8 kOhm on-resistance, housed in an 18-pin PDIP (0.300 in / 7.62 mm) package. An analog multiplexer is a switch network that selects one of several analog input signals and routes it to a single output under digital control. Within the signal-chain hierarchy, the analog multiplexer sits between sensors or signal sources and amplifiers or ADCs, and is itself a member of the broader analog switch IC family. Fault-protected multiplexers add a critical layer: their inputs tolerate fault voltages far beyond the supply rails, and outputs are forced to a high-impedance state when power is removed, protecting downstream circuitry. Key features of the MAX368 include overvoltage protection up to plus or minus 35V at the analog inputs, channels automatically turned off when power is lost, all digital inputs TTL and CMOS compatible, and internal data latches for channel selection so the addressed channel is held without continuous drive of the address lines. Technical depth: the device operates from plus or minus 15V supplies with 5 nA typical leakage, and switches in approximately 1.5 microseconds on-time and 1 microsecond off-time with break-before-make switching action, ensuring the selected channels never short together during transitions. The C-grade temperature specification covers commercial ranges; E and M grades exist for extended and military environments. Typical applications include industrial data acquisition front ends where wiring faults or misconnection would otherwise destroy a standard CMOS mux, test and measurement input selector stages, and ATE (automated test equipment) channel routing where inputs may exceed supply rails. Design consideration: the 1.8 kOhm on-resistance must be accounted for in settling-time budgets when driving sample-and-hold or ADC inputs, particularly at higher source capacitance. This page synthesizes distributor pricing, verified drop-in grade variants, and practical design notes beyond the summary on the manufacturer datasheet.

RFQ پەیوەندی
MAX4852HETE+ Dual SPDT Analog Switch | Analog Devices
MAX4852HETE+

MAX4852HETE+ Dual SPDT Analog Switch | Analog Devices

The Analog Devices MAX4852HETE+ is a dual SPDT analog switch with over-rail signal handling, supplied in a 16-terminal TQFN surface-mount package. The device provides two independent single-pole, double-throw switching functions in one IC, supporting analog signal routing where one input must connect to one of two possible outputs. Its industrial temperature grade and surface-mount construction suit compact signal-conditioning and test equipment designs. An analog switch is a semiconductor-controlled routing component that connects or disconnects signal paths under digital control. A dual SPDT device extends this category by combining two SPDT channels in a single package. The MAX4852 belongs to the broader analog-switch and multiplexer hierarchy, where it sits between passive mechanical switching and more complex multiplexed signal-acquisition systems. Key features include two SPDT analog switches, over-rail signal handling, 16 terminals, and an exposed-pad TQFN package identified by package code HVQCCN. The square surface-mount package supports compact PCB layouts, while the exposed pad provides a thermal and ground connection when the manufacturer land pattern is followed. Analog Devices identifies the MAX4852 as being in production. The MAX4852 combines two separately controlled routing sections in one IC rather than requiring two discrete single-switch packages. Each SPDT section can direct a common signal toward one of two outputs, making the device useful for source selection, polarity routing, measurement-path switching, and signal-path isolation. Over-rail signal handling identifies the intended capability for signals extending beyond the nominal supply range, subject to the operating limits and absolute maximum ratings in the manufacturer datasheet. Typical applications include automated test equipment, data-acquisition modules, instrumentation, communication equipment, and embedded control systems where analog signals must be routed under software control. Integrating both SPDT channels into one package can simplify routing logic and reduce the number of separate switch components, although each board must still provide proper grounding, signal conditioning, and protection appropriate to its external interfaces. Designers should follow the TQFN exposed-pad land pattern and connect the pad as directed in the manufacturer datasheet. Keep sensitive analog traces away from high-current switching paths, provide a low-impedance ground reference, and verify absolute maximum voltage and current limits against the exact operating conditions. The dual architecture is useful only when both switch sections can use the same supply and ground arrangement. This page consolidates the verified MAX4852 device identity, package details, lifecycle information, application guidance, comparison criteria, and sourcing workflow into one engineering-focused reference. Use the Request a Quote form for current availability, lead time, and commercial terms.

RFQ پەیوەندی
MAX9100EUK+T - 1.0V 5µA Micropower Comparator | Analog Devices
MAX9100EUK+T

MAX9100EUK+T - 1.0V 5µA Micropower Comparator | Analog Devices

The Analog Devices MAX9100EUK+T is a single-supply micropower voltage comparator with 1.0V to 5.5V operation, 5µA quiescent current, and a 5-pin SOT-23 package. It is designed for battery-powered systems that require low-voltage decision-making without the higher supply requirement or current consumption of conventional comparators. A micropower comparator is a voltage-regulator-family analog semiconductor that compares two input voltages and produces a push-pull logic output indicating their relationship. The MAX9100 belongs to the comparator hierarchy and is used as a simple decision element, protection element, or threshold detector between an analog sensor and a digital system. Its low supply voltage and low quiescent current make it suitable for single-cell and coin-cell powered equipment. Key features include operation from a single 1.0V to 5.5V supply, 5µA quiescent current, rail-to-rail input capability, and an open-drain output according to the manufacturer comparison information. The common-mode input range includes the negative supply rail, which helps monitor low-voltage battery signals. The MAX9100EUK+T is specified in the 5-pin SOT-23 package and is supplied in tape-and-reel packaging. The MAX9100 is intended for low-energy signal-chain designs where the comparator must operate directly from a depleted battery or regulated low-voltage rail. Because its supply range begins at 1.0V, it can remain useful as the battery approaches its discharge endpoint. The device is optimized for single-cell systems rather than high-voltage industrial comparison tasks. Typical applications include battery threshold detection, portable sensor interfaces, low-voltage power sequencing, window or level comparison, and simple over-discharge indication. In these systems, the comparator can establish whether a measured voltage is above or below a reference without requiring a powered analog front end with a higher minimum supply. Designers should verify the exact output topology, input limits, propagation delay, and operating-temperature ratings against the current manufacturer datasheet before layout. Input and supply decoupling should be placed close to the device, and unused comparator inputs must not be left floating. The manufacturer application information is the authoritative reference for electrical limits and recommended usage. This product page combines verified manufacturer and distributor information with practical application guidance, pricing context, and design considerations that help engineers evaluate the MAX9100EUK+T for low-voltage battery systems.

RFQ پەیوەندی
MAX9675ECQ+ - 16x16 110MHz Video Crosspoint Switch | Analog Devices
MAX9675ECQ+

MAX9675ECQ+ - 16x16 110MHz Video Crosspoint Switch | Analog Devices

The Analog Devices (formerly Maxim Integrated) MAX9675ECQ+ is a 110MHz, 16x16 non-blocking video crosspoint switch with programmable gain, housed in a 100-pin TQFP (14x14 mm) package. It integrates 16 buffered inputs and 16 buffered outputs, allowing any input to be routed to any output (or to multiple outputs simultaneously) without external buffering. The device operates from a single 2.7V to 5.5V supply and supports -40C to +85C ambient operation. A crosspoint switch is a configurable analog/digital routing element used to connect any of N inputs to any of M outputs under serial or parallel control. Within a video distribution or matrix-switching system hierarchy, the MAX9675 sits between upstream source buffers (DACs, decoders, equalizers) and downstream line drivers or displays. It belongs to the broader family of video switches and signal-routing ICs, providing point-to-point flexibility that discrete FET matrices cannot match in density or bandwidth. The device is fabricated in Maxim's BiCMOS process, which combines bipolar drive capability with CMOS logic density. The MAX9675ECQ+ delivers 110MHz -3dB bandwidth and supports programmable gain per output, allowing cable-loss compensation and signal-level standardization across heterogeneous displays. Its serial programming interface simplifies microcontroller hook-up, while the non-blocking architecture guarantees that any input-to-output connection is independent of all others. Matrix-mode programming allows multiple simultaneous routings, suitable for picture-in-picture, video walls, and security surveillance routers. Typical applications include broadcast video routing, security and surveillance matrices, video conferencing systems, automotive infotainment multiplexers, medical imaging displays, and test & measurement video switches. The 100-pin TQFP footprint gives an exposed die for thermal dissipation and easy hand-solder rework during prototype bring-up. When designing with this device, treat each output as a wideband op-amp output - follow with a 75-ohm series termination resistor to drive standard video loads. Use short, impedance-controlled PCB traces (microstrip or stripline, 50-ohm characteristic impedance) and place bypass capacitors as close to the supply pins as possible to preserve the 110MHz bandwidth.

RFQ پەیوەندی
MC10EL32DTG - 5V ECL ÷2 Divider, 8-TSSOP | onsemi
MC10EL32DTG

MC10EL32DTG - 5V ECL ÷2 Divider, 8-TSSOP | onsemi

The onsemi MC10EL32DTG is a 5V ECL (Emitter-Coupled Logic) divide-by-2 frequency divider supplied in an 8-pin TSSOP surface-mount package. The device contains one divide-by-2 element that toggles on the rising edge of the differential clock input, producing complementary ECL Q and Q-bar outputs suitable for high-speed clock tree applications. Operating from a single −4.2V to −5.7V ECL supply rail with PECL compatibility via external bias, the part delivers sub-nanosecond propagation delay characteristics typical of the 10H/100H ECL logic family. An ECL divider is a digital logic device that divides an input clock frequency by an integer factor (here, 2) using current-steering bipolar transistor stages. ECL devices occupy the top of the logic family hierarchy (faster than TTL/CMOS but higher power consumption), and the MC10EL32 specifically provides the high toggle rates required by telecommunications, instrumentation, and test equipment clock distribution where low phase noise and deterministic timing are paramount. Key features include a VBB reference voltage output that allows single-ended input operation by biasing an unused differential input as a switching reference, asynchronous reset capability for initialization, and complementary differential ECL outputs. The 8-TSSOP package provides a 0.65mm pitch and compact board footprint suitable for high-density backplane designs. Architecturally, the MC10EL32 uses differential current steering with internal emitter-follower output buffering, producing typical propagation delays under 1 ns while maintaining low output skew between Q and Q-bar. The internal VBB reference simplifies PCB design by eliminating the need for external bias networks when single-ended clocks must be AC-coupled. Typical applications include clock synthesis in SONET/SDH telecommunications equipment, frequency counter prescalers, high-speed test and measurement instrumentation, and radar/digital IF signal processing. The PECL-compatible threshold also enables use in 3.3V LVPECL systems via level shifting. When designing with this part, maintain 50-ohm impedance-controlled transmission lines on all ECL signal traces to preserve edge fidelity, and provide robust bypassing (0.1 µF and 0.01 µF capacitors) close to the VEE pin. Use the VBB pin only as a reference bias - it cannot source significant load current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that supplement the manufacturer datasheet and help engineers select, source, and implement the MC10EL32DTG in high-speed clock distribution designs.

RFQ پەیوەندی
MC14017BD - 3-18V CMOS Decade Counter | onsemi
MC14017BD

MC14017BD - 3-18V CMOS Decade Counter | onsemi

The onsemi MC14017BD is a 5-stage Johnson decade counter with a built-in code converter, a 3 V to 18 V operating supply range, and ten decoded outputs in a 16-SOIC package. It converts clock pulses into one-of-ten sequential outputs for digital sequencing, timing, and control applications. The counter also provides a carry output for extending the counting sequence beyond ten states. A decade counter, also called a divide-by-10 counter, belongs to the broader counter and divider hierarchy within CMOS logic and digital timing ICs. Unlike a binary counter, a decade counter produces ten mutually exclusive output states. The Johnson-counter architecture used in the MC14017B is designed to provide high-speed operation and spike-free decoded outputs while retaining fully static operation. Key features include a five-stage Johnson counter, an integrated decimal code converter, ten decoded outputs, positive-going-edge clock updates, and a carry output for cascaded counting. Its 3 V to 18 V supply operation supports both 5 V and 12 V logic systems. The device is offered in a 16-SOIC surface-mount package, while the MC14017BD temperature-grade designation identifies a military-oriented version of the MC14017B family. The MC14017B operates from a single positive supply referenced to ground. Its DC clock-input circuit accommodates slow clock rise times, while the decoded outputs change on the positive-going edge of the clock. A clock-inhibit input provides a second control path for pausing the count, and the asynchronous clear input resets the counter so that output Q0 becomes active for the next clock cycle. Typical applications include decade sequencing, industrial timer and counter modules, stepper-motor position sequencing, programmable logic-controller counters, relay-bank activation sequences, test-equipment timing, and digital clock or display multiplexing. The carry output can also trigger a cascaded decade stage, allowing counters larger than ten states to be constructed with additional devices. For robust implementations, treat the clock, inhibit, and asynchronous clear signals as logic inputs with defined levels during reset. Keep the clock path short to reduce susceptibility to ringing and multiple transitions near the active clock edge. Verify output timing and supply-current behavior across the full intended temperature range before releasing the design. This page combines the manufacturer’s counter architecture, package and lifecycle information with drop-in family references, parameter comparisons, application guidance, and practical design notes for engineers evaluating the MC14017BD.

RFQ پەیوەندی
MC14017BF - 16 MHz Decade Counter | onsemi | Logic IC
MC14017BF

MC14017BF - 16 MHz Decade Counter | onsemi | Logic IC

The onsemi MC14017BF is a five-stage Johnson decade counter with a built-in code converter, operating from a 3 V to 18 V supply in a 16-pin SOIC package. It provides a maximum operating frequency of 16 MHz, a propagation delay of 175 ns at 15 V with a 50 pF load, and ten decoded decade outputs. The counter changes state on the positive-going clock edge and supports both rising-edge and falling-edge operation as well as programmable divide ratios and cascading. A decade counter is a sequential logic device that divides an input clock into ten decoded states. The MC14017BF family combines a five-stage Johnson counter with a decoder, producing one active output for each count from zero through nine. This structure places the MC14017BF in the logic IC hierarchy as a counter and divider within digital semiconductor and clock-control applications. Its principal characteristics include a 3 V to 18 V operating range, a 16 MHz maximum frequency, and a -55 °C to +125 °C temperature range. The Johnson-counter architecture is designed for high-speed operation and spike-free decoded outputs. The SOIC-16-208 mil package supports conventional surface-mount assembly while providing access to the clock, reset, carry, supply, ground, and decoded output functions. The MC14017BF is useful when a system needs to divide a frequency into ten discrete periods, count repetitive events, sequence multiple operations, or create programmable timing intervals. Its carry output enables frequency division beyond ten, allowing several counters to be cascaded. Falling-edge clock operation also makes it suitable for systems in which the triggering signal changes on the falling transition. Typical uses include industrial decade and event counters, clock and frequency dividers, programmable timing modules, sequencing controllers, and test equipment. In a cascaded arrangement, each additional stage extends the effective count range while preserving the decoded-decade behavior of the final stage. The broad supply range supports both low-voltage and higher-voltage industrial logic systems. When laying out the circuit, keep the clock trace short and isolate it from the ten decoded outputs to reduce clock-feedthrough and switching noise. Respect the device's absolute maximum input-voltage limits, provide a stable supply and ground reference, and account for output rise and fall times when driving capacitive loads. This page combines manufacturer specifications, drop-in family alternatives, comparison data, and practical implementation guidance for counter and divider designs.

RFQ پەیوەندی
MC14018BD - 5-Bit CMOS Johnson Counter | onsemi | SOIC-16
MC14018BD

MC14018BD - 5-Bit CMOS Johnson Counter | onsemi | SOIC-16

The onsemi MC14018BD is a five-stage CMOS Johnson counter with asynchronous preset and reset inputs, packaged in a 16-pin SOIC. It increments synchronously on the positive-going edge of the clock, and its five counter outputs support divide-by-N operation when the appropriate feedback connection is used. The device is identified in distributor records as a counter IC with one divide-by-N element, five bits, positive-edge operation, and a 16-SOIC package. A Johnson counter is a binary counter whose outputs change in a shifted sequence rather than following conventional binary counting order. Its feedback structure can implement stable divide-by-N counters when the selected output is returned to the clock or preset logic. This makes the MC14018BD useful in frequency division, sequence generation, timing, and control systems where a configurable count ratio is required. The MC14018B family provides five asynchronously presettable and resettable counter stages. Preset is controlled through a logic-high preset-enable input, while reset provides a separate asynchronous clearing function. Synchronous counting occurs on the rising clock edge, allowing counter state to advance predictably under a defined clock source. The distinction between asynchronous control inputs and synchronous counting is important when designing reset, preset, or cascading behavior. The five counter outputs expose intermediate states of the counting sequence. These outputs can be observed directly for state indication or connected according to the desired divide ratio. Because feedback logic determines the effective modulus, correct wiring and timing must be checked against the manufacturer’s counter configuration and truth-table guidance. Typical uses include digital timing dividers, programmable sequence counters, clock-frequency division, industrial timing modules, and embedded control logic. The SOIC-16 surface-mount package supports compact PCB layouts, while the positive-edge clock architecture works naturally with rising-edge clock sources and standard CMOS control signals. When laying out the circuit, keep clock and control traces short, provide a stable supply reference, and avoid routing sensitive counter outputs directly through long traces adjacent to high-switching nodes. Decoupling should follow the manufacturer’s recommended application guidance. Because preset and reset are asynchronous, their pulse widths and settling behavior should be reviewed before using them for short control pulses. This product record combines the manufacturer function description, package and counter classification, sourcing fields, and practical implementation guidance. It also identifies compatible MC14018-family alternatives while clearly separating confirmed drop-in options from related parts that require different packages or function verification.

RFQ پەیوەندی
MC14018BF - 5-Stage Presettable Counter | onsemi
MC14018BF

MC14018BF - 5-Stage Presettable Counter | onsemi

onsemi MC14018BF is a five-stage Johnson-type, presettable divide-by-N counter with asynchronous preset and reset control, packaged in a 16-pin plastic DIP. The device increments synchronously on the positive-going edge of the clock and provides five decoded decade outputs for applications requiring frequency division, sequencing, or ring-counter operation. A Johnson counter is a synchronous sequential-logic circuit whose output stages feed the next stage in a ring configuration. It belongs to the counter and divider hierarchy within CMOS logic ICs. Unlike a conventional binary ripple counter, the MC14018B implements decade-oriented counting with individually available outputs and separate asynchronous controls for preset and reset. Presetting occurs when the preset-enable input is driven to a logic 1, while the counter can be reset asynchronously through its dedicated reset input. The principal functional characteristics include five Johnson counter stages, positive-edge clock operation, asynchronous preset and reset functions, and five decoded outputs suitable for driving five sequential stages. The asynchronous control paths allow an external system to establish a known count immediately rather than waiting for a clock edge. This is useful when synchronization with another subsystem or a system initialization sequence is required. The MC14018B is implemented as a CMOS logic device, placing it within the low-dropout and low-power digital IC family associated with battery-powered and low-voltage systems. The counter maintains state across clock transitions and can divide an input clock into lower-frequency or sequential timing signals. Its decoded outputs can also act as a five-position ring sequence for sequencing multiple loads or system phases. Typical applications include programmable frequency dividers, digital timing generators, cyclic sequence counters, industrial control logic, and clock-domain distribution. It can be used where a compact five-step sequence is needed without implementing the counter from individual flip-flops. Because preset and reset are asynchronous, the device can also initialize a timing sequence after reset while the surrounding system is settling. PCB implementation requires attention to unused inputs and signal transitions. Follow the onsemi MC14018B datasheet pin-description table for every connection, keep the clock and control traces short, and place any decoupling capacitor close to the supply pins. Because transition behavior can influence adjacent CMOS nets, avoid routing high-current or high-speed signals beside the counter outputs and use a defined reset strategy during power-up. This page combines the functional description, pin and package guidance, application analysis, design notes, and sourcing information for the MC14018BF. The comparison section distinguishes the 16-pin plastic DIP MC14018BF from other MC14018B package and temperature options, helping engineers determine when a footprint or qualification change is required before substitution.

RFQ پەیوەندی
MC14022BD - 4-Stage Octal Counter, 16-SOIC | onsemi
MC14022BD

MC14022BD - 4-Stage Octal Counter, 16-SOIC | onsemi

The onsemi MC14022BD is a four-stage Johnson octal counter with a built-in code converter, packaged in a 16-SOIC. It accepts a positive-going clock edge, operates from a 3 V to 18 V supply, and provides eight decoded outputs whose transitions occur on the rising clock edge. The Johnson-counter architecture is intended to produce spike-free outputs while supporting high-speed operation. MC14022BD is suited to frequency division, sequencing, timing, and digital state-generation circuits where one low-frequency clock must be translated into eight ordered output intervals. An octal counter is a sequential digital-logic component that advances through a fixed sequence of states when driven by clock transitions. The MC14022B family uses a four-stage Johnson counter followed by an integrated decoder. A Johnson counter circulates a defined pattern through four internal stages, while the decoder converts that pattern into eight mutually timed output signals. Within the broader semiconductor hierarchy, the device belongs to the counters and dividers category of CMOS logic ICs. The primary features of the MC14022BD include eight decoded outputs, positive-edge triggering, and spike-free output behavior. Its 3 V to 18 V operating range allows use in both lower-voltage 5 V systems and conventional 15 V industrial logic environments. The four-stage counter provides the basis for dividing an input frequency into eight output periods, while the built-in code converter simplifies implementation compared with a separate binary counter and decoder arrangement. Internally, the part combines four Johnson-counter stages with decoding logic. Each decoded output is normally low and becomes high only during its assigned octal time period. The outputs change on the positive-going edge of the clock pulse, making edge polarity an essential consideration when cascading multiple counters or synchronizing the circuit with other positive-edge-triggered logic. The design supports cascaded frequency division and ordered pulse generation without requiring an external binary-to-octal decoder. Typical applications include divide-by-eight clock generation, programmable timing sequences, industrial control sequencing, digital waveform generation, and phase-distribution circuits. The device can also serve as a compact state decoder when a system requires eight outputs corresponding to successive input-clock intervals. In cascaded arrangements, multiple MC14022BD devices can create longer timing sequences or additional frequency divisions while retaining a consistent positive-edge operating model. Designers should account for output rise and fall times, supply decoupling, and clock-signal integrity when operating near the upper frequency capability of the device. Place the decoupling capacitor close to the supply pins and route the clock away from output lines to avoid unintended coupling. Because the outputs change on the positive-going clock edge, downstream circuitry should use compatible triggering conventions or deliberate inversion where required. This page combines the MC14022BD device description with practical design guidance, verified source links, application-focused engineering context, and a structured comparison of compatible family members. It also organizes sourcing information, compliance fields, package details, and technical search terms to help engineers evaluate the MC14022BD for counter, divider, timing, and sequencing designs.

RFQ پەیوەندی