بەرهەمەکان (720+)

SN74LS641H - 8-Bit Open-Collector Bus Transceiver | onsemi
SN74LS641H

SN74LS641H - 8-Bit Open-Collector Bus Transceiver | onsemi

onsemi SN74LS641H is an 8-bit bipolar bus transceiver with open-collector outputs, supplied under the SN74LS logic family. It provides a practical interface between a digital bus and externally driven data lines, supporting legacy TTL-style equipment, control systems, test fixtures, and industrial data-acquisition designs. The device belongs to the buffer, driver, and transceiver hierarchy within digital logic ICs. A bus transceiver combines two directed data paths in one package. Data can move from the bus into the receiving logic, while the driver section presents the opposite signal direction to the external bus. Its open-collector outputs are important because the output stage can provide a wired-AND function when an appropriate pull-up is present. This characteristic is useful in systems where several devices share a signal line or where bus fault handling requires a passive pull-down behavior. The SN74LS641H is associated with the SN74LS641 octal bus-transceiver family. The SN74LS641 family is identified as an octal device with open-collector outputs. The H suffix distinguishes the onsemi ordering variant from the base family name, while its exact package, temperature grade, lifecycle status, and full electrical limits should be selected from the manufacturer’s order information for the complete MPN. As a member of the low-power Schottky TTL family, the device is associated with 74LS-compatible logic systems. Its open-collector interface can support bus-oriented signal conditioning where conventional totem-pole outputs are unsuitable. Designers should nevertheless verify propagation delay, sink current, output rise time, input thresholds, and supply-voltage tolerances against the exact SN74LS641H datasheet before using it as a timing-critical component. Typical uses include interfacing processor buses to open-collector peripherals, communicating with legacy test equipment, isolating logical signals through a bus-driver stage, and building wired-control networks with external pull-up resistors. In each case, the external pull-up value determines the rise time, bus speed, and current drawn while the output transistor is off. The manufacturer application guidance should govern resistor selection and logic-family interfacing. A key design consideration is the difference between a logic-compatible receiver input and an open-collector driver output. The input side may drive from another TTL-family device, while the output side requires suitable pull-up components and must not exceed the published sink-current and voltage limits. Treat the bus as a wired node, calculate its worst-case loading, and verify contention behavior during power-up, reset, and output disable. This product page combines the confirmed SN74LS641H identity with practical guidance for evaluating bus direction, pull-up requirements, package-dependent PCB compatibility, legacy-logic timing, and procurement alternatives. Exact dimensions, pin assignments, and electrical limits remain tied to the ordered package suffix, while the manufacturer datasheet and product page provide the controlling information for design release.

RFQ پەیوەندی
SN74LS641N - 8-Bit Open-Collector Bus Transceiver | TI
SN74LS641N

SN74LS641N - 8-Bit Open-Collector Bus Transceiver | TI

The Texas Instruments SN74LS641N is an 8-bit octal bus transceiver with open-collector outputs, supplied in a 20-pin PDIP package. It is designed for 5 V systems and supports bidirectional transfer between A and B data buses through direction-control and output-enable inputs. The operating voltage shown for this device is 4.75 V to 5.25 V, with an output-current capability listed as 12 mA. A bus transceiver is a bidirectional digital interface that allows two logic buses to exchange data while controlling the direction of transmission. The SN74LS641N belongs to the broader logic IC and bus-interface hierarchy, combining eight parallel data channels, direction control, and open-collector output behavior in one integrated circuit. Open-collector outputs can support wired bus arrangements when the system includes suitable pull-up components and circuit protection. The principal features of the SN74LS641N are its eight parallel channels, non-inverting data transfer, open-collector outputs, and separate direction control. The device transfers data from the A bus to the B bus or from the B bus to the A bus according to the DIR input state. Its 20-pin PDIP package is intended for conventional through-hole PCB assembly rather than surface-mount production. The SN74LS641N belongs to the SN74LS family of Low-Power Schottky TTL-compatible logic devices. Open-collector output stages are the defining architectural feature, while the direction-control inputs determine which side of the transceiver drives the bus. Because the outputs are open collector, external pull-up resistors are normally required for high-level output states. Exact propagation-delay, output-voltage, input-current, and power-consumption limits should be confirmed in the manufacturer datasheet before release to production. Typical uses include bidirectional parallel-bus interfaces, embedded data acquisition, peripheral isolation, legacy computer buses, and industrial control modules where two logic domains must exchange eight data lines. The device is especially relevant to designs that require controllable bus direction and wired-AND behavior. It can also support bus turnaround in systems where a bus driver changes between source and sink operating modes. PCB design should provide a solid ground plane, minimize loop lengths around direction and enable controls, and place pull-up resistors close to the open-collector bus pins. The 4.75 V to 5.25 V supply range requires a stable 5 V rail. Designers should also account for the additional current drawn by pull-up resistors and verify that every connected bus node can tolerate the resulting pull-up current. This product record combines device classification, source links, drop-in replacement analysis, package considerations, and practical interface guidance. The comparison and application sections clarify where the SN74LS641N fits within octal bus-transceiver designs and which technical details must be checked against the manufacturer datasheet.

RFQ پەیوەندی
SN74LS642N - 8-Bit Open-Collector Bus Transceiver | TI
SN74LS642N

SN74LS642N - 8-Bit Open-Collector Bus Transceiver | TI

The Texas Instruments SN74LS642N is an octal, 8-bit, inverting bus transceiver with open-collector outputs, operating from a 4.75 V to 5.25 V supply in a 20-pin PDIP package. It supports bidirectional asynchronous data-bus communication by transferring data from bus A to bus B or from bus B to bus A according to the DIR input. The G enable input can disable the device to isolate the buses. A bus transceiver is a logic interface that connects two data buses and allows data to travel in either direction. The SN74LS642 belongs to the 74LS low-power Schottky TTL logic family and combines eight bidirectional bus channels with direction and enable control. Open-collector outputs are particularly useful when a bus requires pull-up resistors, wired-AND behavior, or compatibility with another logic family. Key features include eight 1-bit transceiver elements, an inverting data path, open-collector output capability, a 4.75 V to 5.25 V operating range, 12 mA output-current capability, and Schmitt-trigger input behavior. The direction input determines which bus drives the other, while the enable input provides a common control for disabling the transceiver and reducing bus contention. The device is designed for asynchronous, two-way communication between computer or peripheral buses. Its open-collector architecture requires correctly sized external pull-up resistors on each bus. Pull-up resistance, bus capacitance, sink-current capability, and maximum data rate must be considered together because increasing resistance reduces current demand but can slow bus transitions and increase susceptibility to noise. Typical applications include bidirectional instrument buses, peripheral-interface isolation, test and measurement systems, computer data buses, and industrial control interfaces. In each case, the DIR input selects the transmitting direction, while G controls whether the enabled device participates in the bus transaction. The 20-pin PDIP package is suited to through-hole boards and legacy system maintenance. For reliable operation, place pull-up resistors close to the open-collector outputs and keep the shared bus traces short enough to control ringing and crosstalk. Confirm that the external pull-up network can source the required receiver current without exceeding the device's output specifications. Do not enable opposing drivers on the same bus. This page combines device architecture, package and pin information, replacement guidance, comparison criteria, and practical bus-interface design notes to support component selection and board-level implementation.

RFQ پەیوەندی
SN74LS645H - Octal Bus Transceiver | Texas Instruments
SN74LS645H

SN74LS645H - Octal Bus Transceiver | Texas Instruments

Texas Instruments SN74LS645H is an octal bus transceiver designed for asynchronous two-way communication between data buses. The device provides eight parallel data channels, non-inverting transceiver operation, and three-state output control. It is intended for systems in which two bus masters, processors, peripheral devices, or memory devices must exchange data over a shared bus. A bus transceiver is a bidirectional interface IC that combines driver and receiver functions. It allows a device to transmit logic levels onto a bus and receive logic levels from that same bus. The SN74LS645 family reduces the number of external timing requirements by coordinating bus direction and output-enable control, while the three-state outputs permit multiple devices to share common data lines without driving them simultaneously. The SN74LS645 is one member of the SN54LS and SN74LS low-power Schottky TTL logic families. Low-power Schottky TTL combines bipolar transistor logic with Schottky-clamped input stages. This technology is associated with the 74LS family’s established logic levels, system design heritage, and broad use in legacy digital equipment. The octal organization means that one device handles eight signal lines in parallel rather than requiring eight separate single-bit interface circuits. The H suffix identifies the orderable SN74LS645H configuration listed for the octal bus transceiver family. The manufacturer product page and supporting technical descriptions identify the device as an octal transceiver for asynchronous two-way bus communication. Detailed electrical limits, propagation timing, supply-current behavior, temperature grade, and package dimensions should be confirmed in the manufacturer datasheet before release to production. Typical uses include bidirectional processor and peripheral buses, memory-interface buffering, data acquisition systems, test equipment, industrial control logic, and repairs of legacy TTL-based hardware. The device is especially useful where a shared bus requires controllable drive direction and a high-impedance state so that only one participant actively drives the lines during a given transaction. Designers should verify direction and enable truth tables, propagation delay, setup and hold timing, input and output loading, and the available input-to-output voltage margin in the system. A shared bus also requires a defined arbitration method so that no two drivers enable the same line simultaneously. Decoupling and signal-return paths should follow the recommended layout in the manufacturer documentation. This page combines the official product identity with package-oriented sourcing context, replacement guidance, application patterns, and design cautions. The comparisons emphasize electrical and functional interchangeability rather than treating every similarly named 74-series component as a safe substitute. Verify timing and logic behavior on the target board, especially when replacing a component across manufacturers or between commercial and extended-temperature variants.

RFQ پەیوەندی
SN74LS682N - 8-Bit Magnitude Comparator | Texas Instruments
SN74LS682N

SN74LS682N - 8-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS682N is an 8-bit identity and magnitude comparator that compares two binary or BCD words and provides active-low equality and greater-than outputs. It is packaged in a 20-pin PDIP and uses the low-power Schottky TTL logic family for compatible digital-system interfacing. The SN74LS682N supports two 8-bit input buses, A and B, allowing a system to determine whether A equals B or whether A is greater than B. According to the manufacturer datasheet, the device also uses totem-pole output structures. An identity or magnitude comparator is a combinational logic device that accepts two multi-bit operands and produces outputs describing their relative relationship. The SN74LS682 belongs to the broader 74LS comparator family, where an 8-bit magnitude comparator compares parallel data rather than determining the order of two individual bits. Its identity function provides a direct equality result, while its magnitude function provides a greater-than result. These operations are useful in control, sorting, address matching, arithmetic sequencing, and test systems. The principal feature of the SN74LS682N is its dedicated 8-bit comparison architecture. Each operand is presented on a parallel bus, and the internal logic evaluates the complete word rather than requiring a serial sequence of bit-by-bit comparisons. The device provides active-low A=B and A>B outputs, enabling wired-output systems to combine several comparator results. Its 74LS Schottky TTL construction is suited to conventional five-volt logic environments, while the through-hole PDIP package simplifies assembly, inspection, and replacement in legacy or industrial control equipment. The SN74LS682N differs from related devices in the same 74LS family primarily by its output set. The LS682 supplies equality and greater-than functions; not every related magnitude comparator offers the same combination. This distinction is important because a substitute with the same package and pin count is not automatically interchangeable if its output behavior differs. Engineers should compare truth tables, propagation timing, output polarity, supply requirements, and input-current characteristics before approving any replacement. Typical uses include equality detection in digital control systems, BCD value comparisons in industrial controllers, parallel sorting and routing logic, address and identification-word recognition, and legacy test equipment. The comparator can also serve as the central decision element in alarm and sequencing circuits where two eight-bit values must be tested continuously. Its parallel interface makes it suitable when the system already presents complete words and requires a hardware-generated status indication without microcontroller comparison code. PCB design should preserve clear separation between the two operand buses and route each input directly to its corresponding package pin. Decoupling requirements, grounded-return practices, unused-input handling, and TTL input-current budgeting must follow the manufacturer datasheet. Because outputs are active low and totem-pole structured, downstream circuits should account for both voltage levels and fan-out rather than treating the outputs as ideal push-pull signals. Socketed prototypes should also account for contact resistance and contamination at older through-hole connections. This product page combines the manufacturer function description, package information, family distinctions, pin-verification guidance, and application-oriented replacement criteria to support engineering selection. It also identifies the limits of package-only compatibility: a true drop-in replacement must reproduce the SN74LS682N output truth table and electrical timing in addition to matching the 20-pin PDIP footprint.

RFQ پەیوەندی
SN74LS684N - 8-Bit Magnitude Comparator | Texas Instruments
SN74LS684N

SN74LS684N - 8-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS684N is an 8-bit identity and magnitude comparator for binary or BCD words, with active-low A=B and A>B outputs in a 20-pin PDIP package. It compares two parallel 8-bit operands and reports whether the inputs are equal or whether the first operand is greater than the second, supporting arithmetic control, address decoding, test systems, and industrial decision logic. A magnitude comparator is a logic IC that determines the relative ordering of two multibit numbers. It belongs to the comparator, digital logic, logic IC, and semiconductor hierarchies. Unlike a general-purpose processor or programmable controller, the SN74LS684N performs its comparison directly from wired logic inputs, so the result becomes available without firmware or instruction sequencing. The SN74LS684N supports both binary and BCD comparison, and its active-low indication outputs are useful for driving downstream enable, reset, or selection logic. The device is listed in a 20-pin PDIP package with a 0 to 70 °C operating-temperature range. These characteristics make it appropriate for legacy-compatible equipment, industrial control systems, counters, timers, test fixtures, and interface designs that retain through-hole logic boards. The LS series implementation uses Schottky-clamped TTL-compatible logic. Its structured outputs indicate the comparison result while external cascaded logic can extend comparison beyond the native 8-bit width. Design engineers should therefore treat the comparator outputs as active levels rather than passive status indicators, account for propagation delay when chaining stages, and use pull-up or pull-down components wherever the receiving circuit requires a defined inactive level. Typical applications include sorting and classification control, digital test-equipment limit checking, address and threshold comparison, arithmetic-unit control, BCD instrument processing, and industrial sequence controllers. In these systems, the two operand buses feed the comparator, while its equality and greater-than outputs coordinate a counter, register, latch, or alarm without requiring continuous software polling. A critical PCB consideration is the 20-pin PDIP footprint. Pin-1 orientation, notch direction, and adequate spacing around the package must match the board pattern, especially when repairing legacy equipment. Keep the input and output traces short enough to limit propagation-delay uncertainty, and account for the operating-temperature limits when using the part outside controlled room-temperature environments. This product page consolidates the device identity, package information, operating range, comparison functions, sourcing structure, replacement guidance, and practical logic-design considerations into an engineering-focused reference. It also highlights the limits of direct substitution by separating true pin-compatible options from related comparator functions that do not reproduce every output and feature of the SN74LS684N.

RFQ پەیوەندی
SN74LS685N - 8-Bit Magnitude Comparator | Texas Instruments
SN74LS685N

SN74LS685N - 8-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS685N is an 8-bit magnitude and identity comparator with inverted logic outputs, supplied in a 20-pin PDIP package. It compares two 8-bit binary numbers and indicates whether the A input is greater than, less than, or equal to the B input. Its three comparison indications support magnitude testing, identity detection, address decoding, conditional control, and digital sorting functions. The SN74LS685N belongs to the LS series of TTL logic and operates as a dedicated combinational comparator rather than a general-purpose arithmetic processor. A magnitude comparator is a digital logic IC that compares two multi-bit unsigned values and produces relational outputs. The SN74LS685N performs this function across two complete 8-bit input groups, reducing the need for several single-bit comparator or gate networks. Magnitude comparators sit within the broader logic-IC hierarchy, alongside arithmetic, interface, memory, and control devices. Their outputs can indicate equality as well as the direction of the numerical relationship, making them useful between data-processing blocks and system decision logic. The defining features are an 8-bit comparison width, inverted comparison outputs, LS-series TTL implementation, and PDIP-20 mechanical package. The inverted outputs are important during logic design because active-low assertions must be treated consistently with the rest of the circuit. The NS suffix identifies the standard Texas Instruments package and commercial-temperature ordering configuration. Because the device uses a through-hole PDIP package, it can also suit educational, industrial-control, test-equipment, and legacy-computing assemblies where through-hole assembly and socketed serviceability remain practical. The SN74LS685N provides a straightforward hardware comparison stage. Two 8-bit buses enter the comparator, while dedicated outputs report the relationship between them. This allows a system to make a decision without first subtracting the operands or comparing them sequentially in a processor. The architecture is particularly useful when a decision must be generated quickly and consistently, or when control logic must respond to equal, greater-than, and less-than conditions independently. Typical applications include digital address decoding, equality checking in control systems, threshold decision logic, numeric sorting networks, event counters, legacy processor interfaces, and industrial automation equipment. In an address decoder, for example, the comparator can test whether a bus matches a programmed or dynamically generated value and enable the associated circuit only when equality is asserted. In test equipment, its three relational outputs can simplify fixture routing and pass-fail detection. PCB design should preserve the logic polarity of the inverted outputs and route each 8-bit input group as a coherent bus to reduce mismatch between corresponding bits. Maintain adequate bypass capacitance at the power pins and avoid relying on the comparator outputs to source loads beyond the device's specified output-current and fan-out limits. When replacing an existing part, verify the complete pinout, supply requirements, temperature range, output timing, and propagation-delay characteristics rather than relying on the comparator function alone. This product page combines the device identity, package details, functional hierarchy, comparison design guidance, practical applications, and drop-in replacement analysis into an engineering-focused reference for the Texas Instruments SN74LS685N 8-bit magnitude comparator.

RFQ پەیوەندی
SN74LS688N 8-Bit Identity Comparator | Texas Instruments
SN74LS688N

SN74LS688N 8-Bit Identity Comparator | Texas Instruments

The Texas Instruments SN74LS688N is an 8-bit identity and magnitude comparator in a 20-pin plastic dual in-line package. It compares two 8-bit binary or BCD words and provides a dedicated P=Q output, while a low-active enable input controls whether the comparison output is actively driven. The device belongs to the SN74LS TTL logic family and is intended for digital systems that need a fast equality decision without implementing the comparison function in general-purpose logic. A magnitude comparator is a combinational logic device that evaluates the relative relationship between two multi-bit values. An identity comparator is the equality-focused subset of that category: instead of reporting greater-than and less-than relationships, the SN74LS688N asserts its P=Q result when the two input words match. In system terms, the device sits between two data buses and a downstream control or decoding circuit, converting eight parallel bit comparisons into one consolidated status signal. The principal features of the SN74LS688N are its 8-bit binary or BCD input capability, P=Q output with enable control, totem-pole output structure, and input hysteresis. These characteristics make it useful where noise immunity and stable switching behavior are important in TTL-compatible equipment. The N suffix denotes the plastic through-hole package, which supports conventional 0.100-inch lead pitch layouts, prototyping, repair work, and legacy industrial control equipment. Internally, the SN74LS688N organizes the comparison into a chain of logic stages that examine corresponding bits from the P and Q buses. Each stage propagates the higher-order comparison result toward the output, allowing the final P=Q signal to reflect the complete eight-bit relationship. External enable control prevents the output from changing state while the compared data is being updated, helping downstream circuitry avoid interpreting intermediate bus states as valid comparisons. Typical applications include digital test equipment, industrial control panels, memory and address checking, sorting and routing control, legacy processor subsystems, and general-purpose binary or BCD data validation. The chip is especially useful when a fixed-width equality result is needed but a larger programmable comparator would be unnecessary. It can also form part of a multi-stage comparison system when several independent 8-bit sections must be checked separately. When laying out a board around the SN74LS688N, maintain the standard 20-pin through-hole footprint and route the two input buses away from high-current switching nodes. The enable input should be driven only when both buses are stable, and unused inputs should be tied to a defined TTL level rather than left floating. Because this is a legacy through-hole logic device, designers should also verify the system supply level, input thresholds, output timing, and noise margin against the manufacturer datasheet before releasing a new production design. This product page adds engineering context beyond the basic catalog entry by organizing the comparison function, package details, application fit, verified source links, and realistic replacement constraints. It also highlights that true drop-in alternatives are limited: substitute parts must preserve the 20-pin footprint, pin functions, logic levels, P=Q behavior, and enable timing rather than merely offering a superficially similar 8-bit comparator.

RFQ پەیوەندی
SN74LS68N - 4-Bit Parallel Binary Accumulator | Texas Instruments
SN74LS68N

SN74LS68N - 4-Bit Parallel Binary Accumulator | Texas Instruments

The Texas Instruments SN74LS68N is a 4-bit parallel binary accumulator counter IC with a listed price of $0.5606 from LCSC as of 2026-10-22 and a verified in-stock listing. The available source data identifies the device as a counter IC, while the broader SN74LS68 function listing describes it as a 4-bit parallel binary accumulator. Its package, pin count, supply ratings, timing, and electrical limits are not stated in the supplied verified records. A parallel binary accumulator is a synchronous counting-logic IC that adds an external addend value to an internal register during an active clock transition. This makes it part of the 74-series TTL logic hierarchy: digital counter, arithmetic logic, digital integrated circuit, and semiconductor. Unlike a basic ripple counter, a parallel accumulator can combine counting and addition functions while presenting a multibit result for address generation, sequencing, instrumentation, or digital control. The N suffix identifies a through-hole Texas Instruments ordering variant, but the exact package technology, number of pins, and dimensions are absent from the verified data. Consequently, the package should not be inferred solely from the suffix. Likewise, propagation delay, output drive, fan-out, supply voltage, and operating temperature cannot be stated safely until the manufacturer datasheet or internal database provides those values. This page preserves those unknowns rather than substituting parameters from a related SN74LS86 quad XOR gate. Potential uses include binary sequencing, digital measurement systems, programmable counters, test equipment, and control logic where parallel addition is useful. Circuit implementation must preserve the device's actual logic polarity, clock requirements, clear behavior, and pinout from the authoritative datasheet. Because those details are not included in the supplied records, they remain explicit data gaps rather than inferred values. For sourcing, DigiKey Marketplace, LCSC, and Octopart provide SN74LS68N listings, but the supplied material does not establish a complete quantity-tier price schedule. LCSC explicitly reports an in-stock status and a starting price of $0.5606. Confirm current stock, lifecycle status, pin-compatible substitutions, and authorized-source traceability before committing a production design. This page combines verified distributor listings, the available functional description, strict data-gap handling, and replacement research. It deliberately excludes unrelated SN74LS86N results and does not claim unverified drop-in alternatives, electrical specifications, pin assignments, or compliance status.

RFQ پەیوەندی
SN74LS697N - 4-Bit Synchronous Up/Down Counter | Texas Instruments
SN74LS697N

SN74LS697N - 4-Bit Synchronous Up/Down Counter | Texas Instruments

The Texas Instruments SN74LS697N is a synchronous 4-bit up/down binary counter with output registers and multiplexed three-state outputs, packaged in a 20-pin PDIP. It combines counting, registered output storage, and bus-oriented output control in one logic device. The device increments or decrements on the active edge of the clock input, supports a 0°C to 70°C operating-temperature grade, and is intended for digital counting and timing systems. A synchronous binary counter is a sequential logic device whose internal state changes in step with an active clock edge. The SN74LS697 belongs to the broader 74LS TTL logic family and combines a counter element with parallel output registers. Its up/down control permits operation as an incrementing counter, decrementing counter, or programmable frequency-divider stage. The output-register stage separates the counting sequence from the signals presented at the multiplexed outputs. The principal features include one 4-bit counting element, a positive-edge clock input, directional counting control, registered outputs, and three-state output capability. The three-state outputs allow multiple counters or other bus-driving devices to share a common data bus when output-enable control is active. This combination is useful in systems requiring orderly bus access, event sequencing, or synchronized transfer of counter values. The SN74LS697N is a member of the SN74LS logic series and uses the SN74LS697 function designation. Its registered outputs provide a defined output state between active clock events, while the synchronous counting architecture simplifies designs where multiple counting stages must update in step. When cascading devices, the carry output can be used to extend counting range and coordinate event boundaries. Typical applications include frequency division, pulse and event counting, programmable timing modules, digital test equipment, industrial sequence controllers, and bus-oriented digital subsystems. The device can also serve as the central counting element in measurement systems that must divide an input frequency, count fixed-duration events, or present a latched hexadecimal or binary count to a host processor. Designers should use the pin-description table in the Texas Instruments SN74LS697 datasheet when assigning PCB signals, especially for output-enable and directional-control pins. Because the outputs are multiplexed and three-state capable, the system must keep output-enable and bus-control timing separate from the clock edge requirements. Unused inputs should be held at a defined logic level according to the datasheet guidance. This page combines the Texas Instruments function description, package information, application guidance, sourcing questions, and replacement constraints into a practical engineering reference for the SN74LS697N. It also distinguishes a verified function-compatible ordering suffix from a genuine cross-manufacturer drop-in equivalent, helping designers avoid assuming that similar counter ICs are pin-compatible without reviewing their datasheets.

RFQ پەیوەندی
SN74LS699N - Synchronous Up/Down Counter | Texas Instruments
SN74LS699N

SN74LS699N - Synchronous Up/Down Counter | Texas Instruments

Texas Instruments SN74LS699N is a synchronous up/down counter with an output register and multiplexed three-state outputs, packaged in a 20-pin plastic DIP. It combines binary counting, direction control, registered parallel outputs, and bus-driving capability in one counter IC. The SN74LS699N is associated with the 74LS TTL logic family and is intended for digital control, sequencing, address-generation, and instrumentation systems where registered counter state must drive shared buses. A counter IC is a member of the broader digital logic hierarchy and increments or decrements a binary state in response to clock events. The 74LS699 architecture adds an output register between the counting section and the external outputs, allowing the presented value to change on a defined clock edge rather than immediately after each internal count transition. This registered architecture helps prevent data races when multiple counters or peripherals share a bus. The principal functional features include synchronous counting in up or down directions, parallel output registers, and multiplexed three-state outputs. Synchronous operation means the counter state advances on the active clock edge, simplifying timing analysis in multi-stage digital systems. The three-state outputs can place each output in a high-impedance state when the device is not driving the shared bus, helping reduce bus contention when several compatible devices are connected. The device belongs to the LS logic series, using bipolar TTL-compatible signal levels and standard 74LS-family interface conventions. The output-register stage separates internal counting activity from bus presentation, while the multiplexer determines which registered information appears on the output bus. Designers should consult the manufacturer pin-description table before assigning PCB tracks because each physical pin must be connected according to its dedicated clock, control, count, or output function. Typical uses include programmable timing generators, pulse and sequence counters, industrial control logic, test-and-measurement equipment, and address or event-counting subsystems. The SN74LS699N is particularly useful when a downstream device requires stable parallel data synchronized to the system clock rather than continuously changing combinational counter outputs. For new PCB layouts, preserve the standard 20-pin DIP footprint and route all supply pins according to the manufacturer datasheet. Avoid substituting a functionally similar counter without checking output timing, output-enable behavior, clear or load semantics, and the exact multiplexing arrangement. These details determine whether a replacement is truly pin-compatible rather than merely equivalent at a high level. This product page combines the counter's core function with package guidance, replacement criteria, comparison data, and practical implementation notes. It is designed to help engineers identify the correct 74LS-family counter, verify bus-interface compatibility, and plan a board-level replacement without overlooking the distinctions between registered, multiplexed, and three-state output implementations.

RFQ پەیوەندی
SN74LS69D - Dual 4-Bit Counter, 16-Pin SOIC | Texas Instruments
SN74LS69D

SN74LS69D - Dual 4-Bit Counter, 16-Pin SOIC | Texas Instruments

Texas Instruments SN74LS69D is a dual 4-bit binary counter operating from a 4.75 V to 5.25 V supply, with up to 25 MHz operating frequency, 54 ns propagation delay, and a 16-pin SOIC package. It is suitable for digital counting, frequency division, timing, sequencing, and control logic applications. A binary counter is a synchronous sequential-logic device that stores and advances a multi-bit count. The SN74LS69 family belongs to the 74LS TTL logic series and provides two 4-bit binary counters with negative-edge triggering. Its decade-counter mode and asynchronous ripple architecture make it useful when compact, low-complexity counting is preferred over a more complex programmable counter. The verified source data identifies the SN74LS69 as a dual 4-bit decade or binary counter. The SN74LS69D ordering code uses the SOIC-16 package. Its listed operating frequency is up to 25 MHz, while the listed propagation delay is 54 ns under a 30 pF load condition. The specified supply-voltage range is 4.75 V to 5.25 V. Typical uses include digital clock dividers, event counters, sequencing circuits, industrial timing modules, and embedded control logic. Because it is a legacy LS-series TTL device, design engineers should account for supply voltage, fan-out, propagation delay, and unused input states rather than assuming compatibility with modern CMOS families. For a new design, keep clock traces short, provide a stable 5 V rail, and decode unused counter outputs carefully. Ripple transitions can propagate through multiple stages, so the maximum frequency and output timing should be checked against the complete cascaded-counter implementation. Verify operating temperature and qualification requirements against the current manufacturer documentation before production release. This product page consolidates distributor availability, technical specifications, package information, and engineering guidance. It also distinguishes verified values from parameters that are not supplied in the retrieved data, helping engineers make a grounded purchasing and design decision.

RFQ پەیوەندی
SN74LS69N - Dual 4-Bit Counter | Texas Instruments | Logic
SN74LS69N

SN74LS69N - Dual 4-Bit Counter | Texas Instruments | Logic

The Texas Instruments SN74LS69N is a dual 4-bit binary counter IC with a 5 V nominal supply, 54 ns propagation delay, and 16 through-hole terminals in a rectangular DIP package. It contains two independent 4-bit counters that count upward and provide parallel binary outputs for each counter section. A binary counter is a synchronous sequential-logic component that records a number as a sequence of binary bits. A 4-bit counter can represent 16 states from 0000 through 1111. As a digital counter IC, the SN74LS69N belongs to the 74LS low-power Schottky TTL family, where digital logic ICs implement counting, timing, and state-sequencing functions within broader control and embedded systems. The principal verified characteristics include dual 4-bit counter organization, upward counting, 54 ns propagation delay, 5 V nominal operating voltage, 16 terminals, commercial temperature grade, and through-hole DIP construction. These specifications make the device suitable for legacy digital control, event counting, sequencing, and industrial automation systems that accept standard 16-pin DIP logic footprints. The SN74LS69N provides two counter sections on one package, reducing board area compared with separate single-counter ICs. Its binary outputs can represent the current count directly, allowing external combinational logic, display drivers, memory systems, or control circuitry to interpret each clock interval. The 54 ns delay provides a concrete timing basis for maximum operating frequency and setup/hold requirements, although a complete design should also examine the complete datasheet waveform and load conditions. Typical applications include industrial batch and piece counting, digital event sequencing, test-equipment timing, legacy process-control interfaces, and educational digital-logic systems. Because the verified listing identifies upward counting and a DIP package, the part is especially relevant to through-hole industrial control boards, repair inventories, and modernization projects that need to preserve an existing 16-pin logic layout. When designing around the SN74LS69N, verify the complete pin assignment, clock-edge requirements, clear behavior, supply tolerances, and output-drive limits against the manufacturer datasheet before layout release. Decoupling and signal-integrity practices remain important even at 54 ns propagation delay: provide local supply bypassing, maintain short clock traces, and avoid relying on long PCB interconnects where edge-sensitive timing could be affected. This page combines verified distributor information, the package and timing data available from market listings, practical legacy-logic design guidance, and carefully qualified drop-in alternatives. It is intended to support component selection and sourcing decisions while clearly separating verified facts from information that still requires confirmation from the full manufacturer documentation.

RFQ پەیوەندی
SN74LS85D - 4-Bit Magnitude Comparator | Texas Instruments
SN74LS85D

SN74LS85D - 4-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS85D is a 4-bit magnitude comparator that compares two four-bit words, A and B, and produces active-high decisions for A<B, A=B, and A>B. It accepts straight binary or straight BCD 8-4-2-1 codes, operates in the 74LS low-power Schottky TTL logic family, and is packaged in a 16-pin SOIC (D) package. The device supports expandable comparisons by cascading multiple units through its higher-order inputs. Its three decoded outputs provide a convenient interface for digital sorting, conditional control, address decoding, and arithmetic sequencing. A magnitude comparator is a combinational logic IC that determines the relative order of two unsigned digital words. Within the broader hierarchy of comparator, digital comparator, logic IC, and semiconductor, the SN74LS85D is designed for fixed-width four-bit comparisons rather than subtraction or signed arithmetic. Because its operation is not restricted to binary, it can also compare monotonic BCD 8-4-2-1 values. The A3 and B3 inputs are the most significant comparison bits, while A0 through A3 and B0 through B3 provide the parallel input set. The main engineering features are three active-high outputs, expansion capability, multi-code operation, and a standard 16-SOIC footprint. The A<B, A=B, and A>B outputs allow a system to decode all three possible relationships without external logic. Expansion inputs permit a larger word width to be implemented by comparing the lower four bits first and feeding the next comparison result into higher-order sections. This makes the device useful where fixed-width ordering must be performed before another digital block makes a decision. In typical applications, the SN74LS85D compares binary counter values, BCD digit values, control registers, or decoded sensor and keypad states. It can drive selection logic in multiplexers, threshold decisions in industrial controls, or sequencing signals in digital systems. Because it is a logic device rather than a power semiconductor, safe-operating-area data is not applicable. Thermal and electrical design should instead focus on supply voltage, input levels, output loading, fan-out, and trace continuity. A key design consideration is to treat unused inputs deliberately. Enable or expansion pins must be tied to a defined logic level rather than left floating, especially in systems where unused TTL inputs can increase noise sensitivity or create unintended current paths. Designers should also verify the relevant supply rail and propagation-delay limits against the system timing budget. The manufacturer datasheet is the authoritative source for electrical limits and pin-level details. This product page combines verified manufacturer and distributor information with application guidance, comparison criteria, and design notes. It is intended to help engineers identify the SN74LS85D for four-bit binary or BCD ordering and to plan a replacement review without assuming that a similar comparator is automatically pin-compatible.

RFQ پەیوەندی
SN74LS85DR - 4-Bit Magnitude Comparator | Texas Instruments (Tape & Reel)
SN74LS85DR

SN74LS85DR - 4-Bit Magnitude Comparator | Texas Instruments (Tape & Reel)

The Texas Instruments SN74LS85DR is a 4-bit magnitude comparator that compares two four-bit words, A and B, and produces active-high decisions for A<B, A=B, and A>B. It accepts straight binary or straight BCD 8-4-2-1 codes, operates in the 74LS low-power Schottky TTL logic family, and is packaged in a 16-pin SOIC (D) package. The device supports expandable comparisons by cascading multiple units through its higher-order inputs. Its three decoded outputs provide a convenient interface for digital sorting, conditional control, address decoding, and arithmetic sequencing. A magnitude comparator is a combinational logic IC that determines the relative order of two unsigned digital words. Within the broader hierarchy of comparator, digital comparator, logic IC, and semiconductor, the SN74LS85DR is designed for fixed-width four-bit comparisons rather than subtraction or signed arithmetic. Because its operation is not restricted to binary, it can also compare monotonic BCD 8-4-2-1 values. The A3 and B3 inputs are the most significant comparison bits, while A0 through A3 and B0 through B3 provide the parallel input set. The main engineering features are three active-high outputs, expansion capability, multi-code operation, and a standard 16-SOIC footprint. The A<B, A=B, and A>B outputs allow a system to decode all three possible relationships without external logic. Expansion inputs permit a larger word width to be implemented by comparing the lower four bits first and feeding the next comparison result into higher-order sections. This makes the device useful where fixed-width ordering must be performed before another digital block makes a decision. In typical applications, the SN74LS85DR compares binary counter values, BCD digit values, control registers, or decoded sensor and keypad states. It can drive selection logic in multiplexers, threshold decisions in industrial controls, or sequencing signals in digital systems. Because it is a logic device rather than a power semiconductor, safe-operating-area data is not applicable. Thermal and electrical design should instead focus on supply voltage, input levels, output loading, fan-out, and trace continuity. A key design consideration is to treat unused inputs deliberately. Enable or expansion pins must be tied to a defined logic level rather than left floating, especially in systems where unused TTL inputs can increase noise sensitivity or create unintended current paths. Designers should also verify the relevant supply rail and propagation-delay limits against the system timing budget. The manufacturer datasheet is the authoritative source for electrical limits and pin-level details. This product page combines verified manufacturer and distributor information with application guidance, comparison criteria, and design notes. It is intended to help engineers identify the SN74LS85DR for four-bit binary or BCD ordering and to plan a replacement review without assuming that a similar comparator is automatically pin-compatible.

RFQ پەیوەندی
SN74LS85N - 4-Bit Magnitude Comparator | Texas Instruments
SN74LS85N

SN74LS85N - 4-Bit Magnitude Comparator | Texas Instruments

The Texas Instruments SN74LS85N is a 4-bit magnitude comparator with eight parallel data inputs, three active-high decision outputs, and 16-PDIP packaging. According to the TI product page, it compares two 4-bit words and supports straight binary and straight BCD (8-4-2-1) codes. It is a standard 74LS-series logic device intended for digital systems requiring A<B, A=B, and A>B decisions. A magnitude comparator is a combinational logic IC that determines the relative ordering of two unsigned binary or coded words. The SN74LS85N accepts A0-A3 and B0-B3, with A3 and B3 serving as the most significant inputs. Its three fully decoded outputs indicate whether the A word is less than, equal to, or greater than the B word. This places it within the broader hierarchy of comparator logic, digital logic IC, and semiconductor. The device supports binary and 8-4-2-1 BCD operation, as stated in the TI datasheet. It can also be expanded to compare words longer than four bits by cascading multiple devices, with the higher-order comparator receiving the lower-order equality result. This makes the SN74LS85N useful in address decoding, sorting control, arithmetic control, industrial control, and embedded digital systems. The SN74LS85N is identified as a 16-pin PDIP by the distributor data. The verified sources identify the function and package but do not provide the complete electrical timing, power, temperature, or pin-level specification tables in the supplied snippets. Those values are therefore marked as data needed rather than inferred. The device uses TTL-compatible LS-series logic, but exact voltage and timing limits should be taken from the manufacturer datasheet before design release. Designers should preserve the device's 16-pin DIP footprint, connect the supply and ground pins according to the datasheet, and account for propagation delay when using comparison results in synchronous control logic. For replacement decisions, verify pinout, power-supply voltage, output behavior, temperature range, and package rather than relying on the magnitude-comparison function alone. This page combines verified distributor and manufacturer information with explicit data gaps for an honest engineering starting point.

RFQ پەیوەندی
SN74LS90D - Decade Counter, 4-Bit, LS-TTL, 14-SOIC | Texas Instruments
SN74LS90D

SN74LS90D - Decade Counter, 4-Bit, LS-TTL, 14-SOIC | Texas Instruments

The Texas Instruments SN74LS90D is a monolithic 4-bit asynchronous decade counter built using low-power Schottky TTL (LS-TTL) technology, supplied in a 14-pin SOIC (D) package. It contains four master-slave flip-flops plus dedicated gating that implements two independent counter sections: a single divide-by-two flip-flop on the A side and a three-stage divide-by-five ripple counter on the B side. The two sections can be cascaded externally to obtain a divide-by-10 (decade, BCD 8421) counter, a symmetrical divide-by-10 (bi-quinary) counter, or a divide-by-12 counter, all selectable by how the QA output is wired back to the B-clock input. A decade counter is a fundamental sequential-logic building block in digital electronics. Decade counters cycle through ten stable output states (0 through 9) before recycling and are widely used as frequency dividers, decimal event counters, and BCD-to-display drivers. As a member of the 74LS (Low-power Schottky) TTL logic family, the SN74LS90 trades raw speed for substantially lower power consumption than the original 74xx series, while retaining TTL-compatible input thresholds and output drive levels that make it easy to interface with legacy 5V system designs, microcontrollers, and discrete indicator drivers. Key features include a guaranteed maximum clock frequency around 30 to 45 MHz at 5V VCC, 14-pin SOIC surface-mount packaging, MSI (medium-scale integration) gate complexity, and fully buffered complementary outputs on all four flip-flop stages. The part operates from a single 4.75V to 5.25V supply and is specified over the commercial 0C to +70C temperature range for the SN74LS90D commercial grade variant. Architecturally, the device uses asynchronous (ripple) clocking - flip-flops toggle on the negative edge of their individual clocks - which simplifies decoding but introduces cumulative propagation delay across the four bits. Engineers planning to decode dynamic states (rather than latched outputs) must factor in the ripple delay when designing overdrive or coincidence logic. Typical applications include digital clock frequency division (divide-by-10 stages used to generate 1 Hz from a 10 Hz oscillator), event counters driving seven-segment displays, decimal counting displays in instrumentation and test equipment, and industrial control panels where a 5V TTL-compatible decade counter is required. The dual divide-by-two / divide-by-five topology also makes the SN74LS90 useful as a general purpose frequency divider to drive lower-speed logic from a higher-rate clock source. When using this device, keep in mind that asynchronous ripple counters are not recommended for high-speed synchronous designs where all bits must update simultaneously; choose a synchronous counter such as the SN74LS160 or SN74LS162 for those cases. Decoupling VCC with a 0.1uF ceramic capacitor close to pin 14 and providing a clean ground reference at pin 7 is essential for reliable counting at high frequencies. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. All information is anchored to TI's official SN74LS90 datasheet, distributor listings, and cross-reference guides valid as of October 2026.

RFQ پەیوەندی
SN74LS90DR - Decade Counter, 4-Bit, LS-TTL, 14-SOIC | Texas Instruments (Tape & Reel)
SN74LS90DR

SN74LS90DR - Decade Counter, 4-Bit, LS-TTL, 14-SOIC | Texas Instruments (Tape & Reel)

The Texas Instruments SN74LS90DR is a monolithic 4-bit asynchronous decade counter built using low-power Schottky TTL (LS-TTL) technology, supplied in a 14-pin SOIC (D) package. It contains four master-slave flip-flops plus dedicated gating that implements two independent counter sections: a single divide-by-two flip-flop on the A side and a three-stage divide-by-five ripple counter on the B side. The two sections can be cascaded externally to obtain a divide-by-10 (decade, BCD 8421) counter, a symmetrical divide-by-10 (bi-quinary) counter, or a divide-by-12 counter, all selectable by how the QA output is wired back to the B-clock input. A decade counter is a fundamental sequential-logic building block in digital electronics. Decade counters cycle through ten stable output states (0 through 9) before recycling and are widely used as frequency dividers, decimal event counters, and BCD-to-display drivers. As a member of the 74LS (Low-power Schottky) TTL logic family, the SN74LS90 trades raw speed for substantially lower power consumption than the original 74xx series, while retaining TTL-compatible input thresholds and output drive levels that make it easy to interface with legacy 5V system designs, microcontrollers, and discrete indicator drivers. Key features include a guaranteed maximum clock frequency around 30 to 45 MHz at 5V VCC, 14-pin SOIC surface-mount packaging, MSI (medium-scale integration) gate complexity, and fully buffered complementary outputs on all four flip-flop stages. The part operates from a single 4.75V to 5.25V supply and is specified over the commercial 0C to +70C temperature range for the SN74LS90DR commercial grade variant. Architecturally, the device uses asynchronous (ripple) clocking - flip-flops toggle on the negative edge of their individual clocks - which simplifies decoding but introduces cumulative propagation delay across the four bits. Engineers planning to decode dynamic states (rather than latched outputs) must factor in the ripple delay when designing overdrive or coincidence logic. Typical applications include digital clock frequency division (divide-by-10 stages used to generate 1 Hz from a 10 Hz oscillator), event counters driving seven-segment displays, decimal counting displays in instrumentation and test equipment, and industrial control panels where a 5V TTL-compatible decade counter is required. The dual divide-by-two / divide-by-five topology also makes the SN74LS90 useful as a general purpose frequency divider to drive lower-speed logic from a higher-rate clock source. When using this device, keep in mind that asynchronous ripple counters are not recommended for high-speed synchronous designs where all bits must update simultaneously; choose a synchronous counter such as the SN74LS160 or SN74LS162 for those cases. Decoupling VCC with a 0.1uF ceramic capacitor close to pin 14 and providing a clean ground reference at pin 7 is essential for reliable counting at high frequencies. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. All information is anchored to TI's official SN74LS90 datasheet, distributor listings, and cross-reference guides valid as of October 2026.

RFQ پەیوەندی
SN74LS90N - 4-Bit Decade Counter | Texas Instruments
SN74LS90N

SN74LS90N - 4-Bit Decade Counter | Texas Instruments

Texas Instruments SN74LS90N is a 4-bit decade counter with asynchronous, negative-edge-triggered operation, TTL logic compatibility, and a 14-pin PDIP package. It divides the input clock by two and provides a three-stage binary count sequence whose overall division ratio is five for the 74LS90 family. The four internal master-slave flip-flops and gating logic allow the counter to be configured for decade-counter operation or other counting sequences required by digital control systems. A decade counter is a synchronous-state counter built from flip-flops and logic gates. In the broader electronics hierarchy, a decade counter belongs to counter logic, digital logic ICs, logic ICs, and ultimately semiconductor devices. It is commonly used to divide one input frequency into lower, predictable frequencies or to produce a modulo-10 counting sequence for timing and control functions. The SN74LS90N provides a 4-bit counter element, negative-edge triggering, and upward counting. Its TTL-compatible interface allows it to operate with other 74LS-family digital logic in established industrial control, instrumentation, and legacy computer systems. Because its counting architecture includes independently controlled sections, designers can also use it in divide-by-five, divide-by-six, divide-by-eight, and related applications depending on the selected output connections. Technically, the monolithic counter combines four master-slave flip-flops with additional gating logic. The master-slave arrangement helps prevent race-through conditions when the clock changes state, while negative-edge triggering defines exactly when the stored count advances. Designers should still account for propagation delay, setup and hold requirements, and output transition behavior when operating near the device’s maximum clock frequency. Typical uses include digital timing references, industrial sequence counters, frequency-divider circuits, test equipment, and embedded legacy control systems. The SN74LS90N is especially appropriate when an existing board requires a standard 14-pin TTL counter rather than a programmable modern counter. Availability and lifecycle decisions should be based on current distributor inventory because legacy through-hole logic sourcing can vary. The primary design consideration is timing margin. Confirm the selected output’s transition timing against the load and the next device’s setup requirement, and route the clock to minimize ringing. Decoupling close to the supply pins and careful grounding remain necessary because every counter edge can propagate supply and ground disturbance into adjacent logic. This page combines verified manufacturer and distributor information, package details, pricing context, sourcing guidance, and verified drop-in alternatives. It also distinguishes documented facts from parameters that still require confirmation from the manufacturer datasheet, helping engineers avoid unsupported assumptions during legacy-logic maintenance and redesign.

RFQ پەیوەندی
SN74LS92D - Divide-by-12 4-Bit Counter | Texas Instruments
SN74LS92D

SN74LS92D - Divide-by-12 4-Bit Counter | Texas Instruments

Texas Instruments SN74LS92D is a divide-by-12, 4-bit, positive-edge-triggered counter IC with one counter element, supplied in a 14-pin SOIC package. The verified distributor listing identifies the device as a counter and divider in the 74LS logic family. Its specified counting function provides modulo-12 state sequencing for digital control, timing, and clock-generation systems, while the 14-SOIC package supports conventional through-hole PCB assembly and breadboard or prototype integration. A counter IC is a synchronous sequential-logic device that advances an internal binary state when it receives an active clock transition. The SN74LS92 belongs to the broader 74LS TTL family, which combines digital counting functions with standard bipolar logic interfaces. Divide-by-12 operation is useful when a system needs a repetitive 12-state sequence rather than a binary modulus of 2, 8, or 16. The output state can therefore be decoded for clock-enable generation, event counting, phase selection, or repetitive control sequencing. The verified data specifically identifies a 4-bit counter, one element, positive-edge triggering, and a divide-by-12 function. The 14-pin SOIC package is the confirmed physical format for the SN74LS92D ordering code. Other operating details, including supply voltage limits, propagation delay, output drive capability, current consumption, and temperature limits, were not included in the supplied verified records and must be confirmed against the manufacturer datasheet before design release. Typical uses include industrial timing modules, digital clock dividers, pulse and event counters, sequencing controllers, and educational digital-logic systems. The positive-edge trigger means the counter changes state on the designated clock transition rather than every clock level. Designers should preserve the counter’s reset behavior and unused input states according to the manufacturer datasheet, and should not substitute a generic counter unless its count modulus, pinout, voltage interface, and timing characteristics are verified as compatible. The primary design consideration is package and logic-family compatibility. SN74LS92D uses a 14-pin SOIC footprint, so a proposed replacement must match that footprint and confirm every terminal function. Supply-voltage compatibility, output timing, fan-out, and signal-integrity margin are especially important when the counter interfaces with slower TTL, faster CMOS, microcontroller, or optocoupler-based systems. This page consolidates verified distributor information, official Texas Instruments product identification, package data, application context, and replacement-screening guidance. The available records do not provide a verified unit price, complete electrical limit table, or five distinct drop-in alternatives; those fields are intentionally marked for verification rather than inferred.

RFQ پەیوەندی
SN74LS92N - Divide-by-12 4-Bit Counter | Texas Instruments
SN74LS92N

SN74LS92N - Divide-by-12 4-Bit Counter | Texas Instruments

The Texas Instruments SN74LS92N is a 4-bit, divide-by-12 ripple counter IC in a 14-pin PDIP package. It provides one counter element, positive-edge operation, and a 12-count sequence for digital frequency division, event counting, timing, and sequencing. The device combines four master-slave flip-flops with gating to implement a divide-by-two section and a three-stage binary counter configured for a divide-by-six cycle. The two sections together produce the overall divide-by-12 function identified by the manufacturer. A ripple counter is a digital counter type within the logic IC hierarchy. Unlike a synchronous counter, its internal stages do not all change on the same clock edge; ripple transitions propagate through successive flip-flops. This architecture is useful when the required count sequence is simple, the clock frequency is moderate, and the next logic stage does not require all counter outputs to switch simultaneously. The SN74LS92N belongs to the SN74LS low-power Schottky TTL family of counters and dividers. The principal functional attributes are its 4-bit counter organization, single divide-by-12 counting element, positive-edge triggering, and 14-pin PDIP package. The verified distributor listing describes the SN74LS92N as a counter and divider IC with one element, four bits, and positive-edge operation. The manufacturer datasheet describes the internal implementation as four master-slave flip-flops plus additional gating. These details distinguish it from decade counters, binary divide-by-8 counters, and general-purpose multi-section counter ICs. Because it uses ripple-style internal propagation, the design should account for the timing relationship among the counter outputs rather than assuming synchronous counter behavior. External logic should be connected to the appropriate decoded count states, and unused inputs must be held at defined logic levels. Power and logic-level details should be confirmed in the current manufacturer datasheet before it is used in a new high-speed or industrial design. Typical applications include divide-by-12 clock generation in older digital systems, pulse and event counting, modulo-12 sequencing, industrial timing modules, and legacy control systems that require a standard TTL counter function. The SN74LS92N is especially relevant for maintaining 74LS-series logic rather than designing a new synchronous counter around a modern programmable device. The primary design trade-off is flexibility versus complexity. A dedicated counter is simpler than a programmable MCU for a fixed modulo-12 function, but its operating speed, logic thresholds, power dissipation, and propagation behavior remain those of the original TTL family. Confirm those characteristics against the manufacturer documentation before replacing a modern high-speed counter in timing-critical circuitry. This page consolidates verified manufacturer and distributor information, package details, practical application guidance, and same-footprint counter alternatives to support component identification, sourcing, and legacy-design maintenance.

RFQ پەیوەندی
SN74LS92NS - Divide-By-Twelve 4-Bit Counter | Texas Instruments | Logic
SN74LS92NS

SN74LS92NS - Divide-By-Twelve 4-Bit Counter | Texas Instruments | Logic

The Texas Instruments SN74LS92NS is a 4-bit ripple-type divide-by-twelve counter built on the 74LS low-power Schottky TTL family, packaged in a 14-pin SOIC (NS) and specified for a 4.75 V to 5.25 V supply. The device combines a divide-by-two counter section with a three-stage binary section whose complete count cycle length is divide-by-six, producing the twelve-count output sequence used in clock, timing and sequencing logic. A counter is a sequential logic circuit that stores and advances a binary count on each applied clock edge. A ripple counter chains several flip-flops so that the carry output of one stage clocks the next, which makes the device inexpensive and simple to cascade but also makes the accumulated propagation delay grow with the number of stages. The 74LS92 family is the classic divide-by-six and divide-by-twelve member of the 74LS counter line that also contains the 74LS90 (decade) and 74LS93 (divide-by-eight) parts. Key features include negative-edge triggered counting, separate clock inputs for the divide-by-two section and the binary section, active-low master reset inputs that clear the count chain, and a standard TTL output stage with symmetrical totem-pole drive. Because the SN74LS92NS is a legacy 74LS part rather than a CMOS part, its supply tolerance matches the classic 5 V rail: 4.75 V minimum to 5.25 V maximum, with a typical quiescent current in the low milliamp range. Internally, the monolithic chip contains four master-slave flip-flops plus gating logic. The master-slave arrangement means the output of a stage changes only after the clock goes low, so the design is free of race conditions when the clock is driven from a debounced switch or a slow ripple network. The divide-by-two section can be cascaded externally with the binary section, giving a divide-by-twelve chain from a single clock source, and the cleared outputs of each stage are often used as qualified enables for downstream gates. Typical uses include frequency division and pulse-train generation, decade and modulus-12 event counters, ring-timing and sequencer stages in industrial control panels, batch and cycle counting in test equipment, and timing references in legacy TTL or microprocessor subsystems that still run from a 5 V rail. When designing with this part, tie all unused clock and master reset inputs to defined logic levels rather than leaving them floating, and place a 0.1 uF bypass capacitor close to the supply pin to keep switching current out of the analog-sensitive ground return. Ripple counters also require an acknowledgement that the summed propagation delay of the chained flip-flops appears as a clock-skew interval at the final output, so the maximum input toggle frequency should be checked against the worst-case delay chain. This page assembles the manufacturer datasheet details, ordering information, equivalent cross-references and practical design notes in one place, adding engineering context that a bare distributor listing does not provide.

RFQ پەیوەندی
SN74LS93D - 4-Bit Binary Counter | Texas Instruments
SN74LS93D

SN74LS93D - 4-Bit Binary Counter | Texas Instruments

Texas Instruments SN74LS93D is a 4-bit binary counter IC with one counting element, negative-edge counting, and a 14-pin SOIC (D) package. The counter supports 0 to 70 °C operation and is described by DigiKey as a 1-element, 4-bit counter. Distributed search results also identify the device as a high-speed 4-bit ripple-type counter assembled from master-slave flip-flops and gating logic. A binary counter is a sequential digital circuit that increments or decrements a binary state when an active clock transition occurs. The SN74LS93 belongs to the 74LS low-power Schottky TTL logic family, whose product hierarchy is 74LS counter → 4-bit binary counter → counter and divider logic → digital logic IC → semiconductor. Its four output bits allow a 16-state counting sequence, while independent gating provides useful divide-by-two and three-stage binary-counter arrangements described for the SN54/74LS90, SN54/74LS92 and SN54/74LS93 family. The verified product information identifies the SN74LS93 as a 4-bit binary counter with a 14-pin SOIC package and negative-edge counting. One distributor result lists a maximum frequency of 42 MHz. The part is also described as supporting decade, divide-by-twelve and binary-counter functions, with gated sections that allow the designer to select the required counting arrangement. These characteristics make it suitable for legacy digital logic, frequency division, event counting and industrial control systems that retain 5 V TTL-compatible interfaces. Ripple-counter architecture uses cascaded flip-flop stages, so each internal stage supplies clocking information to the following stage. This structure can introduce cumulative propagation delay between output transitions. Designers should therefore account for settling time when decoding several outputs together, particularly if the decoded value must remain glitch-free around a carry transition. The reset and control inputs should be driven with clean, stable logic to prevent unintended count initialization or count-enable behavior. Typical uses include dividing a periodic signal, counting external events in legacy instrumentation, sequencing digital state machines and building compact binary accumulators. The counter is particularly relevant to brownfield industrial equipment, test fixtures and communication modules that use 74LS-family logic rather than modern programmable controllers. Because the verified material does not provide a detailed external clock or reset circuit, engineers should consult the manufacturer datasheet for exact truth-table and timing conditions before finalizing a board. For a new design, keep clock and control traces short, provide a stable ground reference and decode outputs only after the expected propagation delay has elapsed. Avoid relying on decoded ripple outputs without considering transition hazards. Verify the actual device markings, supply requirements and absolute maximum ratings because only the counter width, package, edge sensitivity, temperature range and summarized functions were provided in the verified search data. This page combines verified manufacturer and distributor information with practical selection guidance, a strict drop-in review, sourcing questions and design considerations for engineers maintaining TTL-based systems. It also clearly separates confirmed data from parameters that still require confirmation from the official SN74LS93 datasheet.

RFQ پەیوەندی
SN74LS93DR - 4-Bit Binary Counter | Texas Instruments (Tape & Reel)
SN74LS93DR

SN74LS93DR - 4-Bit Binary Counter | Texas Instruments (Tape & Reel)

Texas Instruments SN74LS93DR is a 4-bit binary counter IC with one counting element, negative-edge counting, and a 14-pin SOIC (D) package. The counter supports 0 to 70 °C operation and is described by DigiKey as a 1-element, 4-bit counter. Distributed search results also identify the device as a high-speed 4-bit ripple-type counter assembled from master-slave flip-flops and gating logic. A binary counter is a sequential digital circuit that increments or decrements a binary state when an active clock transition occurs. The SN74LS93 belongs to the 74LS low-power Schottky TTL logic family, whose product hierarchy is 74LS counter → 4-bit binary counter → counter and divider logic → digital logic IC → semiconductor. Its four output bits allow a 16-state counting sequence, while independent gating provides useful divide-by-two and three-stage binary-counter arrangements described for the SN54/74LS90, SN54/74LS92 and SN54/74LS93 family. The verified product information identifies the SN74LS93 as a 4-bit binary counter with a 14-pin SOIC package and negative-edge counting. One distributor result lists a maximum frequency of 42 MHz. The part is also described as supporting decade, divide-by-twelve and binary-counter functions, with gated sections that allow the designer to select the required counting arrangement. These characteristics make it suitable for legacy digital logic, frequency division, event counting and industrial control systems that retain 5 V TTL-compatible interfaces. Ripple-counter architecture uses cascaded flip-flop stages, so each internal stage supplies clocking information to the following stage. This structure can introduce cumulative propagation delay between output transitions. Designers should therefore account for settling time when decoding several outputs together, particularly if the decoded value must remain glitch-free around a carry transition. The reset and control inputs should be driven with clean, stable logic to prevent unintended count initialization or count-enable behavior. Typical uses include dividing a periodic signal, counting external events in legacy instrumentation, sequencing digital state machines and building compact binary accumulators. The counter is particularly relevant to brownfield industrial equipment, test fixtures and communication modules that use 74LS-family logic rather than modern programmable controllers. Because the verified material does not provide a detailed external clock or reset circuit, engineers should consult the manufacturer datasheet for exact truth-table and timing conditions before finalizing a board. For a new design, keep clock and control traces short, provide a stable ground reference and decode outputs only after the expected propagation delay has elapsed. Avoid relying on decoded ripple outputs without considering transition hazards. Verify the actual device markings, supply requirements and absolute maximum ratings because only the counter width, package, edge sensitivity, temperature range and summarized functions were provided in the verified search data. This page combines verified manufacturer and distributor information with practical selection guidance, a strict drop-in review, sourcing questions and design considerations for engineers maintaining TTL-based systems. It also clearly separates confirmed data from parameters that still require confirmation from the official SN74LS93 datasheet.

RFQ پەیوەندی