بەرهەمەکان (22,000+)

AT90USB1286-AUR - 128KB USB 2.0 AVR MCU | Microchip
AT90USB1286-AUR

AT90USB1286-AUR - 128KB USB 2.0 AVR MCU | Microchip

The Microchip AT90USB1286-AUR is a low-power 8-bit AVR RISC microcontroller with 128KB of ISP flash memory, 8KB SRAM, 4KB EEPROM, and a 64-pin TQFP package. It operates at 16MHz and integrates USB 2.0 low-speed and full-speed device connectivity, 48 general-purpose I/O lines, 10-bit ADC channels, four timer/counters, USART, and a byte-oriented two-wire serial interface. An 8-bit microcontroller is a programmable semiconductor that executes instructions from nonvolatile flash memory and uses SRAM for working data. The AT90USB1286 belongs to the AVR family of RISC microcontrollers and combines general-purpose embedded processing with a dedicated USB device controller. This integration allows a single device to manage application logic, peripheral control, data acquisition, and direct USB communication without a separate USB interface controller. Its 128KB in-system programmable flash supports read-while-write operation, while the optional boot-code section, independent lock bits, and factory-programmed USB bootloader simplify firmware development and production programming. The 10-bit ADC provides eight channels for analog measurement, and the four flexible timer/counters support compare modes and PWM output. USART and two-wire serial interfaces expand the available communication options for sensors, external memory, and industrial peripherals. The enhanced AVR architecture provides an 8-bit RISC core operating at 16MHz, combining general-purpose embedded processing with dedicated USB device connectivity. Forty-eight general-purpose I/O lines support digital interfaces, while 32 general-purpose working registers help the core organize and manipulate data. The USB controller supports both low-speed and full-speed USB 2.0 device operation, making the device suitable for USB-connected control, measurement, and human-interface equipment. Typical uses include USB keyboards and other human-interface devices, USB data-acquisition equipment, bootloaders, industrial interface controllers, communications equipment, and custom USB peripherals. The 128KB flash capacity is useful for protocol stacks, boot code, application firmware, and USB class drivers that must coexist within one compact controller. PCB design should preserve high-speed USB signal integrity by routing D+ and D- as a short, tightly matched pair and placing the required USB transceiver support components near the controller. The 64-pin TQFP footprint also demands careful escape routing around the perimeter, while decoupling should be distributed close to supply pins. Use the manufacturer pin-description table and USB hardware guidance when assigning tracks and selecting protection components. This product page combines the manufacturer’s core device specifications with practical USB layout guidance, interface-selection context, and structured comparisons of verified AT90USB family alternatives. It supports faster component identification while keeping the final schematic, footprint, firmware, and USB validation decisions with the engineer.

RFQ پەیوەندی
AT90USB1286-MU - 16MHz 128KB USB AVR MCU | Microchip
AT90USB1286-MU

AT90USB1286-MU - 16MHz 128KB USB AVR MCU | Microchip

The Microchip Technology AT90USB1286-MU is an 8-bit AVR RISC-based microcontroller operating at up to 16 MHz, with 128 KB of flash memory and a 64-QFN (9 x 9 mm) package. It integrates USB 2.0 low-speed and full-speed device connectivity, 48 general-purpose I/O lines, 8 KB of SRAM, 4 KB of EEPROM, and an 8-channel 10-bit ADC. The part operates from a 2.7 V to 5.5 V supply. An AVR microcontroller is a compact embedded-control processor based on the reduced instruction set computer architecture. The AT90USB1286 family combines general-purpose digital control, USB communications, serial interfaces, timers, and analog conversion in one device. It belongs to the hierarchy of 8-bit microcontroller, RISC microcontroller, embedded processor, and semiconductor. USB integration allows the same device to manage peripheral control while presenting a standard interface to a host computer. The principal features include 128 KB of ISP flash with read-while-write capability, 4 KB of EEPROM, 8 KB of SRAM, and 48 general-purpose I/O lines. Four flexible timer/counter blocks provide compare and PWM functions, while USART and byte-oriented 2-wire serial interfaces support external sensors and peripherals. An 8-channel, 10-bit ADC provides analog measurement, and the integrated USB controller supports USB 2.0 full-speed operation up to 12 Mbit/s and low-speed operation up to 1.5 Mbit/s. The enhanced RISC architecture supports throughput approaching 1 MIPS per MHz, giving the AT90USB1286-MU up to 16 MIPS at 16 MHz. On-chip USB functionality removes the need for a separate USB interface controller in host-managed peripherals. Read-while-write flash supports firmware updates, while EEPROM preserves calibration, configuration, or user data independently of the main program memory. The MCU also includes real-time counter, USART, JTAG debugging, and timer resources for connected embedded products. Typical applications include USB-connected human-interface devices, keyboard controllers, test and measurement equipment, data-acquisition systems, USB-to-serial adapters, industrial control modules, and compact consumer peripherals. The 48 I/O lines provide flexibility for sensors, indicators, communication buses, and control signals, while the internal ADC reduces the component count for analog front ends that do not require more than 10-bit resolution. When designing around the AT90USB1286-MU, verify USB signal routing, supply decoupling, and exposed-pad thermal design against the manufacturer datasheet. Provide a compliant USB connection and ensure the firmware budget fits the 128 KB flash and 8 KB SRAM limits. Confirm the operating voltage and industrial-temperature requirements for the assembled product before releasing the PCB design. This page organizes the core memory, USB, analog, timing, and package characteristics while adding practical application guidance, direct engineering comparisons, and design considerations that help engineers evaluate the AT90USB1286-MU before schematic capture and PCB layout.

RFQ پەیوەندی
AT90USB1286-MUR - 16MHz 128KB USB AVR MCU | Microchip
AT90USB1286-MUR

AT90USB1286-MUR - 16MHz 128KB USB AVR MCU | Microchip

The Microchip Technology AT90USB1286-MUR is a 16 MHz, 8-bit AVR RISC microcontroller with 128 KB of ISP flash memory, 8 KB SRAM, 4 KB EEPROM, and USB 2.0 device connectivity in a 64-QFN 9 x 9 mm package with an exposed pad. It combines 48 general-purpose I/O lines with USB full-speed and low-speed operation for compact human-interface, peripheral, and control designs. An 8-bit AVR RISC microcontroller is a compact embedded-processing component that combines program memory, data memory, digital and analog peripherals, and communication interfaces on one device. Within the semiconductor hierarchy, the AT90USB1286 belongs to the microcontroller family and functions as a general-purpose system controller with a dedicated USB device controller. Its integrated architecture reduces the need for external USB interface devices in USB-connected equipment. The AT90USB1286 includes 128 KB of in-system-programmable flash with read-while-write capability, 8 KB of static RAM, and 4 KB of EEPROM. These memories support downloaded firmware, working data, and nonvolatile configuration storage. Its 48 general-purpose I/O lines provide flexible connections for keyboards, control panels, sensor interfaces, communications, and human-interface devices. Four flexible timer/counter blocks add compare and PWM functions for timing, dimming, motor control, and waveform generation. Communications and mixed-signal resources are integrated into the same controller. The device includes a USART, byte-oriented two-wire serial interface, USB 2.0 low-speed and full-speed device operation, an eight-channel 10-bit ADC, and JTAG on-chip debugging. The manufacturer describes up to 16 MIPS throughput, making the part suitable for real-time control tasks that must respond quickly while communicating with a USB host. Typical uses include USB keyboards and pointing devices, human-interface adapters, embedded control panels, USB-connected instrumentation, data acquisition front ends, and industrial peripherals. Engineers can use the USB interface for configuration, logging, firmware updating, or direct host-to-device control. The 48 I/O lines also allow the same MCU to supervise external sensors and actuators instead of requiring a separate interface IC. The exposed-pad QFN requires careful PCB layout and adequate thermal dissipation. Follow the manufacturer datasheet for the exposed-pad connection, pin assignment, decoupling requirements, clock configuration, and USB signal-routing guidance. USB differential traces should be routed as a controlled impedance pair, with minimal vias and uninterrupted return paths, while the USB transceiver supply and ground connections should be placed close to the device. This product page combines manufacturer specifications, family-level comparisons, sourcing guidance, and practical design guidance. It helps engineers distinguish the 128 KB AT90USB1286 from lower-memory AT90USB devices and assess whether its integrated USB, analog, timing, and communications resources fit a specific embedded design.

RFQ پەیوەندی
AT90USB1287-AU - 16MHz 128KB USB AVR MCU | Microchip
AT90USB1287-AU

AT90USB1287-AU - 16MHz 128KB USB AVR MCU | Microchip

Microchip Technology AT90USB1287-AU is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 128 KB of ISP flash memory, 4 KB of EEPROM, 8 KB of SRAM, and integrated USB 2.0 low-speed and full-speed On-The-Go support in a 64-TQFP 14 x 14 mm package. It combines 48 general-purpose I/O lines, 32 working registers, four timer/counter blocks with PWM, USART, two-wire serial interface, an eight-channel 10-bit ADC, and a real-time counter. The architecture supports throughput approaching 16 MIPS at 16 MHz, while the read-while-write ISP flash allows applications to be updated through the device’s programming interface without interrupting operation in the same manner as a conventional flash-memory restriction. An AVR microcontroller is an 8-bit RISC semiconductor that combines a processor core, program memory, data memory, and peripherals on one integrated circuit. The AT90USB1287 belongs to the 90USB hierarchy of Microchip AVR devices designed for USB-connected embedded control. Unlike a discrete USB interface solution, its integrated USB controller, general-purpose I/O, serial interfaces, timers, and ADC allow a compact design to manage data exchange, analog measurement, timing, and control functions using one microcontroller. The principal feature of the AT90USB1287-AU is native USB 2.0 connectivity operating at low speed and full speed. According to the Microchip product-page data, the device also supports USB On-The-Go operation, while the 48 GPIO pins provide extensive connectivity for sensors, indicators, controls, and external interface devices. Four flexible timer/counter blocks with compare modes and PWM support precise periodic generation, while the real-time counter, USART, byte-oriented two-wire serial interface, and eight-channel 10-bit ADC broaden its embedded-control capabilities. The 128 KB flash and 8 KB SRAM provide substantially more code and working-memory capacity than smaller AVR USB controllers. Read-while-write ISP flash supports firmware maintenance in systems where code execution can continue from another program-memory region during a suitable update operation. The AVR enhanced RISC core executes instructions in a single clock cycle for many common operations, giving the device a stated throughput approaching 1 MIPS per MHz, or approximately 16 MIPS at its 16 MHz operating frequency. Typical uses include USB human-interface interface controllers, USB-to-serial equipment, bootloaders and firmware update systems, USB-connected instrumentation, industrial control panels, data acquisition modules, and embedded accessories. Its integrated ADC makes it appropriate for monitoring eight analog channels, while its timer/counter PWM resources can drive indicators, motor-control signaling, or other periodic outputs. The integrated USB controller is especially useful when a design requires a compact interface without a separate USB transceiver or host controller. Designers should budget 64 package pins, confirm the exact pin assignments and alternate functions in the manufacturer datasheet, and provide the required USB transceiver, crystal or clock components, bypass capacitors, and programming access. USB bus routing should follow the applicable layout guidance, and analog inputs require suitable filtering and grounding. The 2.7 V to 5.5 V operating range supports both 3.3 V and 5 V systems, but peripheral and USB requirements must be evaluated together before selecting the system supply voltage. This product record consolidates verified manufacturer, distributor, and cross-reference information into a selection-focused comparison with same-package alternatives, commercial data, and practical design guidance. It distinguishes documented capabilities from unavailable details instead of estimating missing electrical, timing, compliance, or lifecycle information.

USD $13.62 لە کۆگادایە
AT90USB1287-MU - 128KB USB AVR MCU | Microchip Technology
AT90USB1287-MU

AT90USB1287-MU - 128KB USB AVR MCU | Microchip Technology

The Microchip Technology AT90USB1287-MU is an 8-bit AVR RISC-based USB microcontroller with 128KB of ISP flash memory, 4KB of EEPROM, 8KB of SRAM, and 48 general-purpose I/O lines in a 64-QFN 9 x 9 mm package. It operates at up to 16MHz and integrates low-speed and full-speed USB 2.0 connectivity. A microcontroller is a programmable semiconductor that combines a processor core, nonvolatile program memory, data memory, peripherals, and input/output interfaces on one integrated circuit. The AT90USB1287 belongs to the AVR 8-bit microcontroller family and combines the enhanced RISC architecture with a dedicated USB controller. This makes it suitable for systems that require local control logic, data acquisition, human-interface connectivity, or USB device communication without adding a separate USB interface controller. Key features include 128KB of read-while-write ISP flash memory, 4KB of EEPROM, 8KB of SRAM, 32 general-purpose working registers, and 48 general-purpose I/O lines. Four flexible timer/counter blocks provide compare modes and PWM outputs, while USART and byte-oriented 2-wire serial interfaces support external peripherals and board-level communication. The integrated USB controller supports USB 2.0 low-speed and full-speed operation. The AVR enhanced RISC architecture is designed for efficient embedded control, with most instructions executing in a single clock cycle. At a maximum clock frequency of 16MHz, the AT90USB1287 combines substantial nonvolatile memory with a broad peripheral set. Its 48 I/O lines allow the device to connect sensors, actuators, indicators, and communication transceivers while retaining USB as the primary host interface. Typical applications include USB-connected human-interface devices, industrial data-acquisition equipment, USB-to-serial or USB-to-control adapters, instrumentation, bootloader-capable embedded products, and compact USB peripherals. Its combination of EEPROM, SRAM, timers, serial interfaces, and USB makes it especially useful where firmware configuration, peripheral control, and direct USB connectivity must coexist in one package. When laying out the PCB, follow the manufacturer pin-description table for the 64-QFN footprint and its exposed thermal-pad connection. Place USB signal routing away from noisy analog or switching paths, provide compliant USB impedance and power-path layouts, and decouple each supply rail close to its associated pins. Firmware should also use the device-specific boot and clock configuration procedures from the manufacturer documentation. This page combines the exact orderable MPN, memory and peripheral specifications, package information, application guidance, and qualified same-family drop-in alternatives. It also organizes PCB, firmware, and replacement-selection considerations that help engineers evaluate the AT90USB1287-MU before integrating it into a new USB-enabled embedded design.

RFQ پەیوەندی
AT90USB1287-MUR - 128KB USB AVR MCU | Microchip Technology (Tape & Reel)
AT90USB1287-MUR

AT90USB1287-MUR - 128KB USB AVR MCU | Microchip Technology (Tape & Reel)

The Microchip Technology AT90USB1287-MUR is an 8-bit AVR RISC-based USB microcontroller with 128KB of ISP flash memory, 4KB of EEPROM, 8KB of SRAM, and 48 general-purpose I/O lines in a 64-QFN 9 x 9 mm package. It operates at up to 16MHz and integrates low-speed and full-speed USB 2.0 connectivity. A microcontroller is a programmable semiconductor that combines a processor core, nonvolatile program memory, data memory, peripherals, and input/output interfaces on one integrated circuit. The AT90USB1287 belongs to the AVR 8-bit microcontroller family and combines the enhanced RISC architecture with a dedicated USB controller. This makes it suitable for systems that require local control logic, data acquisition, human-interface connectivity, or USB device communication without adding a separate USB interface controller. Key features include 128KB of read-while-write ISP flash memory, 4KB of EEPROM, 8KB of SRAM, 32 general-purpose working registers, and 48 general-purpose I/O lines. Four flexible timer/counter blocks provide compare modes and PWM outputs, while USART and byte-oriented 2-wire serial interfaces support external peripherals and board-level communication. The integrated USB controller supports USB 2.0 low-speed and full-speed operation. The AVR enhanced RISC architecture is designed for efficient embedded control, with most instructions executing in a single clock cycle. At a maximum clock frequency of 16MHz, the AT90USB1287 combines substantial nonvolatile memory with a broad peripheral set. Its 48 I/O lines allow the device to connect sensors, actuators, indicators, and communication transceivers while retaining USB as the primary host interface. Typical applications include USB-connected human-interface devices, industrial data-acquisition equipment, USB-to-serial or USB-to-control adapters, instrumentation, bootloader-capable embedded products, and compact USB peripherals. Its combination of EEPROM, SRAM, timers, serial interfaces, and USB makes it especially useful where firmware configuration, peripheral control, and direct USB connectivity must coexist in one package. When laying out the PCB, follow the manufacturer pin-description table for the 64-QFN footprint and its exposed thermal-pad connection. Place USB signal routing away from noisy analog or switching paths, provide compliant USB impedance and power-path layouts, and decouple each supply rail close to its associated pins. Firmware should also use the device-specific boot and clock configuration procedures from the manufacturer documentation. This page combines the exact orderable MPN, memory and peripheral specifications, package information, application guidance, and qualified same-family drop-in alternatives. It also organizes PCB, firmware, and replacement-selection considerations that help engineers evaluate the AT90USB1287-MUR before integrating it into a new USB-enabled embedded design.

RFQ پەیوەندی
AT90USB162-16AU - 16MHz USB AVR MCU | Microchip Technology
AT90USB162-16AU

AT90USB162-16AU - 16MHz USB AVR MCU | Microchip Technology

The Microchip Technology AT90USB162-16AU is a low-power 8-bit AVR RISC microcontroller with an integrated USB controller, a 16 MHz clock, 16 KB of ISP flash memory, 512 bytes of SRAM, 512 bytes of EEPROM, and 22 general-purpose I/O lines. The device is packaged in a 32-pin TQFP measuring 7 mm by 7 mm and operates from a 2.7 V to 5.5 V supply. An 8-bit microcontroller is a compact embedded-control platform that combines a processor core, nonvolatile program memory, working memory, peripheral interfaces, and general-purpose input/output in one integrated circuit. The AT90USB162 belongs to the AVR 90USB family, where the AVR-enhanced RISC architecture executes instructions efficiently and the integrated USB interface allows a product to connect directly as a USB peripheral without a separate USB controller. The AT90USB162-16AU provides 16 KB of ISP flash with read-while-write capability, 512 bytes of EEPROM, and 512 bytes of SRAM. Its peripheral set includes two flexible timer/counters with compare and PWM functions, a USART, SPI, a programmable watchdog timer with an internal oscillator, and 22 general-purpose I/O lines. A 16 MHz operating speed supports deterministic control and USB peripheral tasks in compact embedded products. Its architecture combines the AVR processing core with dedicated USB functionality and conventional serial interfaces. Read-while-write flash permits program-memory access during supported operation, while the EEPROM provides nonvolatile parameter storage and SRAM supports temporary working data. The wide 2.7 V to 5.5 V supply range permits operation from common 3.3 V and 5 V rails, while USB connectivity reduces the component count required for a USB-connected peripheral. Typical applications include USB human-interface devices, data-acquisition equipment, medical-device interfaces, industrial automation controllers, and service-oriented USB peripherals. The integrated USB controller is especially useful for keyboard, mouse, control-panel, diagnostic-interface, and configuration adapters where compactness, low power, and direct host connectivity are important. The 32-pin TQFP footprint requires careful fanout between the dense peripheral pins and the external USB, clock, decoupling, and programming connections. Place the required input and output capacitors close to the device, maintain the USB signal path as a short controlled-impedance route, and verify the board against the manufacturer pin-description table and reference design before fabrication. This product page combines device specifications, application guidance, package information, and a verified same-footprint alternative assessment. It also identifies the design constraints that matter most when implementing the AT90USB162-16AU in a USB-enabled embedded system.

RFQ پەیوەندی
AT90USB162-16MU - 16MHz AVR USB MCU | Microchip Technology
AT90USB162-16MU

AT90USB162-16MU - 16MHz AVR USB MCU | Microchip Technology

The Microchip Technology AT90USB162-16MU is an 8-bit AVR RISC microcontroller operating at 16 MHz, with 16 KB of ISP Flash memory, 512 bytes of SRAM, 512 bytes of EEPROM, and 22 general-purpose I/O lines in a 32-VQFN 5 x 5 mm package. It combines an AVR-enhanced RISC core, USB connectivity, serial interfaces, timers, and programmable watchdog support in a compact surface-mount device. An 8-bit AVR microcontroller is a compact embedded processor intended for control-oriented products that coordinate peripherals, read sensors, update displays, and manage communication links. Its RISC-oriented instruction set, working registers, and dedicated peripheral modules place the AT90USB162 within the hierarchy of microcontrollers, embedded processors, and semiconductor control devices. The product is particularly relevant to USB-connected human-interface, communications, and compact embedded-control designs. Key features include 16 KB of read-while-write ISP Flash, 512 bytes of EEPROM, and 512 bytes of SRAM. The device provides 22 general-purpose I/O lines and 32 general-purpose working registers. Two flexible timer/counters with compare modes and PWM, a USART, SPI, and a programmable watchdog timer support typical embedded-control duties. Its 16 MHz maximum clock speed provides approximately one MIPS-per-MHz-class execution capability for its AVR-enhanced RISC architecture. The AT90USB162 architecture integrates USB interface hardware with an 8-bit AVR core, allowing a compact design to connect to a USB host without implementing a separate USB controller. ISP Flash supports in-system programming, while read-while-write operation allows nonvolatile code storage to remain useful during certain programming operations. The manufacturer describes the family as a low-power CMOS implementation combining 16 KB ISP Flash with 512-byte EEPROM and 512-byte SRAM. Typical applications include USB human-interface devices, firmware update and bootloader equipment, USB-to-serial adapters, compact data-acquisition controllers, and industrial peripherals. The 22 I/O lines provide interfaces for buttons, indicators, sensors, and external transceivers, while the timers, USART, and SPI broaden its usefulness beyond a basic USB bridge. The 32-VQFN footprint is appropriate for compact USB accessories and embedded modules. Board design requires careful attention to USB signal integrity, exposed-pad soldering, decoupling, and programming access. Place the USB traces according to the manufacturer reference layout, keep the exposed thermal pad soldered to the ground plane, and provide local bulk and high-frequency bypass capacitors close to the supply pins. Confirm the exact pin functions and alternate-pin assignments in the Microchip pin-description table before routing the PCB. This page combines the AT90USB162 family specifications, package information, documented drop-in family alternatives, application guidance, and design-focused comparisons to help engineers evaluate USB MCU integration before schematic capture and PCB layout.

RFQ پەیوەندی
AT90USB646-AU - 16MHz 64KB USB AVR MCU | Microchip
AT90USB646-AU

AT90USB646-AU - 16MHz 64KB USB AVR MCU | Microchip

The Microchip Technology AT90USB646-AU is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 64 KB of ISP flash memory, 2 KB of EEPROM, 4 KB of SRAM, and USB 2.0 low-speed and full-speed device support in a 64-pin TQFP package. It provides 48 general-purpose I/O lines, 32 general-purpose working registers, four flexible timer/counters with compare modes and PWM, a USART, and a byte-oriented two-wire serial interface. A microcontroller is a compact programmable controller that integrates a processor core, memory, and peripherals on one semiconductor device. The AT90USB646 belongs to the hierarchy of 8-bit MCU -> AVR RISC microcontroller -> embedded controller -> semiconductor. Its built-in USB controller allows a board to enumerate as a USB peripheral and exchange data with a host without a separate USB interface IC, while the AVR core supports typical embedded control, communication, and human-interface-device workloads. Key features include read-while-write ISP flash, 64 KB of program memory, 2 KB of EEPROM, 4 KB of SRAM, and a USB 2.0 controller supporting low-speed and full-speed operation. The four timer/counter blocks provide compare and PWM functions, while the USART and two-wire serial interface add communication options beyond USB. The 48 I/O lines provide substantial external connectivity for buttons, indicators, sensors, and peripheral control signals. The AT90USB646-AU combines an 8-bit AVR enhanced RISC processor with dedicated USB and communications peripherals in one device. Its 64 KB flash allocation supports embedded USB firmware, boot code, and application logic in a single controller. Read-while-write operation can improve firmware-update flexibility by allowing supported memory operations during programming, subject to the detailed restrictions in the manufacturer datasheet. The device also includes an 8-channel, 10-bit ADC according to the available product information. Typical uses include USB-connected human-interface devices, HID peripherals, USB-to-serial bridges, bootloaders, data-acquisition controllers, and embedded systems that need both USB connectivity and general-purpose I/O. Its integrated USB controller reduces board complexity in devices that communicate directly with a USB host. The 16 MHz operating clock supports deterministic embedded control, and the timer/counter PWM resources can drive indicator LEDs, motor-control signals, or periodic tasks. The primary design consideration is package and firmware compatibility. The -AU ordering uses a 64-pin TQFP package, so board layout, exposed-pad handling, and pin assignment must follow the manufacturer package drawing rather than a generic 64-pin footprint. USB routing also requires careful placement of the transceiver connection, protection components, and grounding. Firmware should be validated against the USB enumeration, suspend, resume, and bus-power requirements specified by Microchip. This page consolidates the verified distributor listing, manufacturer product information, and cross-reference results into an engineering-focused view of memory, connectivity, package, and replacement options. It also distinguishes true same-footprint choices from functional equivalents that require PCB or firmware changes.

RFQ پەیوەندی
AT90USB646-AUR - 16MHz 64KB USB AVR MCU | Microchip (Tape & Reel)
AT90USB646-AUR

AT90USB646-AUR - 16MHz 64KB USB AVR MCU | Microchip (Tape & Reel)

The Microchip Technology AT90USB646-AUR is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 64 KB of ISP flash memory, 2 KB of EEPROM, 4 KB of SRAM, and USB 2.0 low-speed and full-speed device support in a 64-pin TQFP package. It provides 48 general-purpose I/O lines, 32 general-purpose working registers, four flexible timer/counters with compare modes and PWM, a USART, and a byte-oriented two-wire serial interface. A microcontroller is a compact programmable controller that integrates a processor core, memory, and peripherals on one semiconductor device. The AT90USB646 belongs to the hierarchy of 8-bit MCU -> AVR RISC microcontroller -> embedded controller -> semiconductor. Its built-in USB controller allows a board to enumerate as a USB peripheral and exchange data with a host without a separate USB interface IC, while the AVR core supports typical embedded control, communication, and human-interface-device workloads. Key features include read-while-write ISP flash, 64 KB of program memory, 2 KB of EEPROM, 4 KB of SRAM, and a USB 2.0 controller supporting low-speed and full-speed operation. The four timer/counter blocks provide compare and PWM functions, while the USART and two-wire serial interface add communication options beyond USB. The 48 I/O lines provide substantial external connectivity for buttons, indicators, sensors, and peripheral control signals. The AT90USB646-AUR combines an 8-bit AVR enhanced RISC processor with dedicated USB and communications peripherals in one device. Its 64 KB flash allocation supports embedded USB firmware, boot code, and application logic in a single controller. Read-while-write operation can improve firmware-update flexibility by allowing supported memory operations during programming, subject to the detailed restrictions in the manufacturer datasheet. The device also includes an 8-channel, 10-bit ADC according to the available product information. Typical uses include USB-connected human-interface devices, HID peripherals, USB-to-serial bridges, bootloaders, data-acquisition controllers, and embedded systems that need both USB connectivity and general-purpose I/O. Its integrated USB controller reduces board complexity in devices that communicate directly with a USB host. The 16 MHz operating clock supports deterministic embedded control, and the timer/counter PWM resources can drive indicator LEDs, motor-control signals, or periodic tasks. The primary design consideration is package and firmware compatibility. The -AU ordering uses a 64-pin TQFP package, so board layout, exposed-pad handling, and pin assignment must follow the manufacturer package drawing rather than a generic 64-pin footprint. USB routing also requires careful placement of the transceiver connection, protection components, and grounding. Firmware should be validated against the USB enumeration, suspend, resume, and bus-power requirements specified by Microchip. This page consolidates the verified distributor listing, manufacturer product information, and cross-reference results into an engineering-focused view of memory, connectivity, package, and replacement options. It also distinguishes true same-footprint choices from functional equivalents that require PCB or firmware changes.

RFQ پەیوەندی
AT90USB646-MU - 16MHz USB AVR MCU 64-QFN | Microchip
AT90USB646-MU

AT90USB646-MU - 16MHz USB AVR MCU 64-QFN | Microchip

The Microchip Technology AT90USB646-MU is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 64 KB of ISP flash memory, 2 KB EEPROM, 4 KB SRAM, and integrated USB 2.0 low-speed and full-speed device support, all housed in a 64-QFN 9 x 9 mm package. The device combines 48 general-purpose I/O lines, 32 working registers, four timer/counter resources with compare and PWM modes, a USART, and a byte-oriented two-wire serial interface. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, and peripherals into one compact device. The AVR family belongs to the embedded-controller hierarchy: general-purpose MCU, embedded controller, processor, and semiconductor. AT90USB646-MU targets systems that need local control logic combined directly with USB connectivity, avoiding a separate USB interface controller when the firmware and host software support the AVR platform. Verified product information identifies read-while-write ISP flash, 2 KB EEPROM, 4 KB SRAM, 48 I/O lines, 32 general-purpose working registers, a real-time counter, four flexible timer/counters, PWM, USART, and a byte-oriented two-wire serial interface. Its integrated USB controller supports low-speed and full-speed USB 2.0 operation. These resources make the MCU suitable for compact USB-connected control, data-acquisition, human-interface, bootloader, and embedded peripheral products. The 16 MHz operating frequency provides the timing basis for the AVR core, while the 64 KB flash region stores firmware and 4 KB SRAM supports runtime data. Compared with a larger AVR controller, the AT90USB646 remains resource-focused, yet its 48 I/O lines and USB integration offer substantial peripheral connectivity. Designers must also account for the exposed-pad package, USB signal routing, decoupling, clock stability, and programming requirements. Typical implementations include USB HID controllers, DFU-capable embedded products, USB-to-serial equipment, data loggers, keyboard and control-panel firmware, and small industrial or instrumentation modules. It is particularly useful when a compact, single-chip design needs both deterministic embedded processing and USB device connectivity. PCB implementation requires a 64-QFN land pattern, adequate thermal copper, and short USB differential routing. The supplied data does not provide detailed operating-voltage limits, pin names, or thermal limits, so those values must be checked against the official manufacturer documentation before release to production. This page consolidates the verified manufacturer and distributor information, clarifies the controller's core resources, and identifies practical selection considerations. Pricing and stock are intentionally not inferred because exact commercial values were not supplied; compare authorized distributor quotations and the official product page before procurement.

RFQ پەیوەندی
AT90USB646-MUR - 16MHz USB AVR MCU 64-QFN | Microchip (Tape & Reel)
AT90USB646-MUR

AT90USB646-MUR - 16MHz USB AVR MCU 64-QFN | Microchip (Tape & Reel)

The Microchip Technology AT90USB646-MUR is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 64 KB of ISP flash memory, 2 KB EEPROM, 4 KB SRAM, and integrated USB 2.0 low-speed and full-speed device support, all housed in a 64-QFN 9 x 9 mm package. The device combines 48 general-purpose I/O lines, 32 working registers, four timer/counter resources with compare and PWM modes, a USART, and a byte-oriented two-wire serial interface. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, and peripherals into one compact device. The AVR family belongs to the embedded-controller hierarchy: general-purpose MCU, embedded controller, processor, and semiconductor. AT90USB646-MUR targets systems that need local control logic combined directly with USB connectivity, avoiding a separate USB interface controller when the firmware and host software support the AVR platform. Verified product information identifies read-while-write ISP flash, 2 KB EEPROM, 4 KB SRAM, 48 I/O lines, 32 general-purpose working registers, a real-time counter, four flexible timer/counters, PWM, USART, and a byte-oriented two-wire serial interface. Its integrated USB controller supports low-speed and full-speed USB 2.0 operation. These resources make the MCU suitable for compact USB-connected control, data-acquisition, human-interface, bootloader, and embedded peripheral products. The 16 MHz operating frequency provides the timing basis for the AVR core, while the 64 KB flash region stores firmware and 4 KB SRAM supports runtime data. Compared with a larger AVR controller, the AT90USB646 remains resource-focused, yet its 48 I/O lines and USB integration offer substantial peripheral connectivity. Designers must also account for the exposed-pad package, USB signal routing, decoupling, clock stability, and programming requirements. Typical implementations include USB HID controllers, DFU-capable embedded products, USB-to-serial equipment, data loggers, keyboard and control-panel firmware, and small industrial or instrumentation modules. It is particularly useful when a compact, single-chip design needs both deterministic embedded processing and USB device connectivity. PCB implementation requires a 64-QFN land pattern, adequate thermal copper, and short USB differential routing. The supplied data does not provide detailed operating-voltage limits, pin names, or thermal limits, so those values must be checked against the official manufacturer documentation before release to production. This page consolidates the verified manufacturer and distributor information, clarifies the controller's core resources, and identifies practical selection considerations. Pricing and stock are intentionally not inferred because exact commercial values were not supplied; compare authorized distributor quotations and the official product page before procurement.

RFQ پەیوەندی
AT90USB647-AU - 16MHz AVR USB Microcontroller | Microchip
AT90USB647-AU

AT90USB647-AU - 16MHz AVR USB Microcontroller | Microchip

The Microchip AT90USB647-AU is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 64 KB of flash memory, 4 KB of SRAM, and 2 KB of EEPROM in a 64-TQFP package. It integrates USB 2.0 low-speed and full-speed On-The-Go connectivity, 48 general-purpose I/O lines, 32 working registers, USART, a byte-oriented 2-wire serial interface, timers with PWM support, and a real-time counter. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The AT90USB647 belongs to the AVR 8-bit microcontroller family and is designed for embedded USB control, human-interface devices, data acquisition, and industrial peripheral applications. Its USB On-The-Go support can simplify device-to-device connectivity while reducing the need for separate USB interface hardware. The verified product information identifies 64 KB of ISP flash memory with read-while-write capability, 2 KB of EEPROM, 4 KB of SRAM, and 48 general-purpose I/O lines. The 16 MHz operating frequency supports responsive control-loop and USB firmware execution, while the 3.3 V and 5 V supply description identifies compatibility with common embedded system rails. The part is available in a 64-pin TQFP package and tray packaging according to the supplied distributor data. The AT90USB647-AU architecture is based on Microchip’s enhanced AVR RISC core and includes four flexible timer/counters with compare modes and PWM, USART, byte-oriented 2-wire serial interface, USB 2.0 low-speed/full-speed On-The-Go, and a real-time counter. These peripherals allow firmware to manage USB data, serial communications, timing events, motor or LED control, and sensor acquisition without requiring several discrete support devices. Typical applications include USB keyboards and mice, HID-class human-interface equipment, USB-to-serial adapters, data loggers, embedded instrumentation, and USB-connected industrial control modules. The large memory footprint is useful for bootloader code, protocol stacks, configuration data, and application firmware, while the broad I/O count supports multiple external peripherals on a single board. When designing around the AT90USB647-AU, confirm the USB connector, transceiver integration, power-supply sequencing, clock implementation, and decoupling requirements against the manufacturer datasheet. Use the specified 64-TQFP footprint and verify all 64 pin assignments before layout. USB signal routing and cable or connector behavior also require board-level validation. This page combines the verified Microchip product description, distributor specifications, package data, source links, and application guidance to support engineering selection and sourcing of the AT90USB647-AU.

RFQ پەیوەندی
AT90USB647-AUR - 16MHz 64KB USB AVR MCU | Microchip
AT90USB647-AUR

AT90USB647-AUR - 16MHz 64KB USB AVR MCU | Microchip

The Microchip Technology AT90USB647-AUR is an 8-bit AVR RISC microcontroller with USB 2.0 device support, 64KB of ISP flash memory, 2KB EEPROM, 4KB SRAM, and 48 general-purpose I/O lines. It operates at up to 16MHz and is packaged in a 64-pin TQFP (14x14 mm) tape-and-reel option. Its integrated USB controller supports low-speed and full-speed operation, while the AVR core provides a compact platform for USB-connected control, data acquisition, human-interface, and embedded peripheral designs. A microcontroller is an integrated computing device containing a processor core, nonvolatile program memory, working memory, and dedicated peripherals. The AT90USB647 belongs to the hierarchy of AVR 8-bit RISC microcontrollers, embedded microcontrollers, and general-purpose semiconductor integrated circuits. Its USB connectivity, moderate memory capacity, and 48 I/O pins make it suitable for systems that need local control without the cost or complexity of a higher-bit-width processor. Key device features include 64KB of flash with read-while-write capability, 2KB EEPROM, 4KB SRAM, 48 I/O lines, 32 general-purpose working registers, and four flexible timer/counter blocks with compare and PWM modes. The device also includes USART, byte-oriented two-wire serial interface, and USB 2.0 low-speed and full-speed On-The-Go support. These resources consolidate several control and communication tasks into one device. The AT90USB647-AUR combines a 16MHz AVR architecture with dedicated USB connectivity, allowing firmware to enumerate as a USB peripheral while using timers for timing, PWM for actuator control, and serial interfaces for sensors or external modules. Its 48 I/O lines provide substantial board-level connectivity for indicators, buttons, relays, displays, and data-capture circuits. The 2KB EEPROM supports nonvolatile parameter storage, while the 4KB SRAM provides working memory for protocol handling and control state. Typical applications include USB bootloaders, USB-to-serial bridges, industrial control modules, USB-connected instrumentation, human-interface devices, and embedded accessory controllers. The manufacturer product page also identifies MPLAB Snap and ICSP connectivity, supporting programming and debugging workflows. The 64-pin TQFP footprint offers a conventional leaded surface-mount package for prototype and production assemblies where a higher pin-count analog or mixed-signal interface is useful. When designing around this MCU, confirm the USB operating mode, clocking arrangement, power requirements, and every exposed-pin function against the manufacturer datasheet before layout. Route USB D+ and D- as a controlled-impedance differential pair, keep the interface away from noisy switching nodes, and provide the decoupling and crystal or clock circuitry recommended by the application reference design. Firmware should also use the USB descriptors and device identifiers appropriate to the finished product. This page consolidates verified manufacturer and distributor specifications, practical USB design guidance, same-family comparisons, and sourcing information. It adds engineering context around memory, connectivity, programming, and package reuse without replacing the complete manufacturer datasheet for production design release.

RFQ پەیوەندی
AT90USB647-MU 16MHz 64KB USB MCU | Microchip Technology
AT90USB647-MU

AT90USB647-MU 16MHz 64KB USB MCU | Microchip Technology

The Microchip Technology AT90USB647-MU is an 8-bit AVR RISC microcontroller with USB 2.0 device support, 64KB of ISP flash memory, 2KB of EEPROM, 4KB of SRAM, and 48 general-purpose I/O lines. It operates at up to 16MHz and is supplied in a 64-pin VFQFN package with an exposed pad. The device combines an AVR microcontroller, USB connectivity, serial interfaces, timers, and modular peripherals in one integrated package. A microcontroller is a programmable semiconductor that executes firmware, coordinates digital peripherals, and provides the central control logic for embedded products. The AT90USB series belongs to the AVR family of low-power 8-bit RISC devices. In a USB-enabled product, the controller can manage host-to-device data transfer, firmware updates, configuration handling, and application-specific control functions without requiring a separate USB interface controller. The verified feature set includes 64KB of flash with read-while-write capability, 2KB of EEPROM, 4KB of SRAM, and 32 general-purpose working registers. The device provides USB 2.0 low-speed and full-speed On-The-Go support, a USART, a byte-oriented 2-wire serial interface, a real-time counter, and four flexible timer/counters with compare modes and PWM. These resources support USB peripherals, human-interface devices, data acquisition, industrial control, communication bridges, and embedded USB test equipment. The 64-pin package leaves substantial I/O capacity for USB data, programming, debugging, serial communication, timers, and application signals. The exposed pad is intended for thermal management, but actual power dissipation and layout requirements depend on clock rate, I/O activity, supply voltage, ambient temperature, and PCB construction. The supplied data confirms industrial-temperature ordering information through the AT90USB647-MU listing, while detailed operating-temperature limits should be confirmed in the manufacturer datasheet. Typical designs place the microcontroller beside USB protection, clock circuitry, decoupling capacitors, programming access, and application-specific sensors or transceivers. Designers should preserve the exposed-pad land pattern, route USB differential signals with controlled impedance, keep high-current paths compact, and validate firmware compatibility before production release. AT90USB647-MU is a tray-packaged ordering option; the exact exposed-pad dimensions and complete pin map are not fully included in the supplied source snippets. This product page combines the verified Microchip feature summary, distributor package information, and application-oriented design guidance. Pricing and lead time vary by supplier, so procurement should be confirmed against current distributor listings as of 2026-10-23. The data also identifies AT90USB647-MUR as a closely related reel-packaging designation, but packaging form alone is not treated here as a separate drop-in alternative.

RFQ پەیوەندی
AT90USB647-MUR 16MHz 64KB USB MCU | Microchip Technology (Tape & Reel)
AT90USB647-MUR

AT90USB647-MUR 16MHz 64KB USB MCU | Microchip Technology (Tape & Reel)

The Microchip Technology AT90USB647-MUR is an 8-bit AVR RISC microcontroller with USB 2.0 device support, 64KB of ISP flash memory, 2KB of EEPROM, 4KB of SRAM, and 48 general-purpose I/O lines. It operates at up to 16MHz and is supplied in a 64-pin VFQFN package with an exposed pad. The device combines an AVR microcontroller, USB connectivity, serial interfaces, timers, and modular peripherals in one integrated package. A microcontroller is a programmable semiconductor that executes firmware, coordinates digital peripherals, and provides the central control logic for embedded products. The AT90USB series belongs to the AVR family of low-power 8-bit RISC devices. In a USB-enabled product, the controller can manage host-to-device data transfer, firmware updates, configuration handling, and application-specific control functions without requiring a separate USB interface controller. The verified feature set includes 64KB of flash with read-while-write capability, 2KB of EEPROM, 4KB of SRAM, and 32 general-purpose working registers. The device provides USB 2.0 low-speed and full-speed On-The-Go support, a USART, a byte-oriented 2-wire serial interface, a real-time counter, and four flexible timer/counters with compare modes and PWM. These resources support USB peripherals, human-interface devices, data acquisition, industrial control, communication bridges, and embedded USB test equipment. The 64-pin package leaves substantial I/O capacity for USB data, programming, debugging, serial communication, timers, and application signals. The exposed pad is intended for thermal management, but actual power dissipation and layout requirements depend on clock rate, I/O activity, supply voltage, ambient temperature, and PCB construction. The supplied data confirms industrial-temperature ordering information through the AT90USB647-MUR listing, while detailed operating-temperature limits should be confirmed in the manufacturer datasheet. Typical designs place the microcontroller beside USB protection, clock circuitry, decoupling capacitors, programming access, and application-specific sensors or transceivers. Designers should preserve the exposed-pad land pattern, route USB differential signals with controlled impedance, keep high-current paths compact, and validate firmware compatibility before production release. AT90USB647-MUR is a tray-packaged ordering option; the exact exposed-pad dimensions and complete pin map are not fully included in the supplied source snippets. This product page combines the verified Microchip feature summary, distributor package information, and application-oriented design guidance. Pricing and lead time vary by supplier, so procurement should be confirmed against current distributor listings as of 2026-10-23. The data also identifies AT90USB647-MURR as a closely related reel-packaging designation, but packaging form alone is not treated here as a separate drop-in alternative.

RFQ پەیوەندی
AT90USB82-16MU - 16MHz USB AVR MCU | Microchip
AT90USB82-16MU

AT90USB82-16MU - 16MHz USB AVR MCU | Microchip

The Microchip Technology AT90USB82-16MU is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 8 KB of self-programming ISP flash memory, 512 bytes of SRAM, 512 bytes of EEPROM, and USB connectivity in a 32-pin VQFN package measuring 5 mm by 5 mm. The -16MU suffix identifies the 16 MHz grade, while the M suffix denotes the surface-mount package configuration. An 8-bit microcontroller is a compact embedded-processing device that executes instructions from a program memory and interacts with external hardware through general-purpose I/O pins. The AT90USB82 belongs to the AVR family and the broader AT90USB product group, combining a RISC architecture, USB device connectivity, and read-while-write flash in a single device. This combination makes it suitable for USB-connected peripheral, human-interface, and firmware-update applications. According to the Microchip product page, the device provides 22 general-purpose I/O lines, 32 general-purpose working registers, and two flexible timer/counter blocks with compare and PWM capabilities. It supports 135 instructions, with most instructions completing within a single clock cycle, and can execute up to 16 million instructions per second at 16 MHz. Its operating voltage range of 2.7 V to 5.5 V supports both 3.3 V and 5 V system designs. Program development is supported through 8 KB of ISP flash with read-while-write capability, 512 bytes of EEPROM for nonvolatile data, 512 bytes of SRAM, and an on-chip DebugWire interface. USB firmware can use the device's DFU bootloader capability, while the AVR architecture and DebugWire interface support in-circuit debugging. Detailed peripheral pin assignments are not included in the supplied source data. Typical uses include low-speed USB adapters, keyboard and mouse controllers, HID peripherals, industrial interface modules, and USB-connected embedded accessories. The 5 V by 5 mm VQFN package minimizes board area, but its exposed-pad construction requires careful PCB thermal design and a suitable copper landing area. When designing the layout, place the USB transceiver and its supporting components near the package, maintain the required impedance-controlled USB traces, and provide stable decoupling at each supply pin. Because this is a fine-pitch VQFN, verify pad dimensions, paste stencil apertures, solder mask clearance, and the exposed-pad paste pattern against the manufacturer footprint before releasing artwork. This page consolidates distributor availability, verified device specifications, package information, and practical engineering guidance. It also identifies the scarcity of confirmed pin-to-pin replacements, helping designers distinguish true drop-in alternatives from related AVR devices that require schematic, firmware, or PCB changes.

RFQ پەیوەندی
AT91FR40161-CI - 33MHz ARM7 MCU, 2MB Flash | Microchip
AT91FR40161-CI

AT91FR40161-CI - 33MHz ARM7 MCU, 2MB Flash | Microchip

The Microchip Technology AT91FR40161-CI is a 33 MHz ARM7-based 16/32-bit RISC microcontroller with 2 MB of embedded Flash, 1M x 16 configuration, and 120-LBGA packaging in a 17 x 11 mm format. It is designed for embedded systems requiring a high-performance 32-bit processor, external-memory interfacing, serial communications, and integrated watchdog supervision. The industrial-grade AT91FR40161-CI combines an ARM Thumb-compatible architecture with embedded ICE, on-chip SRAM, and an EBI/EMI interface for connecting external memory and peripherals. A microcontroller is a programmable semiconductor device that integrates a processor core, memory, peripherals, and communication interfaces on one package. The AT91 family belongs to the broader hierarchy of embedded processors, microcontrollers, and semiconductor devices. It is appropriate for industrial controllers and embedded equipment where deterministic peripheral access, external bus connectivity, and a compact surface-mount footprint are more important than a highly integrated wireless interface. The AT91FR40161-CI provides a 33 MHz clock, a 32-bit data bus with single-cycle access, and 256K-word Flash organized as 2 MB in a 1M x 16 arrangement. Its integration includes EBI/EMI, UART/USART, and a Watchdog Timer. Embedded ICE supports in-circuit debugging and emulation workflows, reducing the need for external debug infrastructure. The 120-terminal LBGA also provides substantially more connection density than a leaded or small-outline package. The ARM7 processor executes 32-bit instructions while supporting the denser 16-bit Thumb instruction set. This combination provides access to a larger instruction space and more efficient compact code generation. The peripheral set is organized around embedded control rather than graphics or high-speed networking, making the device suitable for control loops, data acquisition, communication gateways, and supervisory systems that require deterministic behavior. Typical applications include industrial data-acquisition equipment, serial-control panels, embedded test systems, communication controllers, and compact industrial controllers. The EBI/EMI interface is especially useful when the system needs external RAM, flash, or peripheral devices. UART/USART connections support external sensors, modems, service interfaces, and operator consoles, while the watchdog helps recover a system after a software or hardware fault. PCB design should preserve the voltage and signal requirements of the 120-ball footprint, provide clean power distribution, and route the external-bus signals with appropriate timing margin. Software development should account for memory mapping, watchdog servicing, peripheral initialization, and the ARM7/Thumb execution mode. This page combines device characteristics, practical design considerations, application guidance, and verified sourcing information for engineers evaluating the AT91FR40161-CI.

RFQ پەیوەندی
AT91FR40162-CI - 75MHz ARM7 MCU | Microchip Technology
AT91FR40162-CI

AT91FR40162-CI - 75MHz ARM7 MCU | Microchip Technology

The Microchip Technology AT91FR40162-CI is an ARM7 16/32-bit microcontroller with a 75 MHz clock, 2 MB of embedded Flash memory organized as 1M x 16, 256 KB of on-chip SRAM, and a 121-ball BGA package measuring 10 x 10 mm. It integrates an External Bus Interface, two USARTs, a three-channel timer/counter, a watchdog timer, and dedicated embedded ICE debug pins. An ARM7 microcontroller is a 32-bit reduced-instruction-set-computing core that can execute a compact 16-bit Thumb instruction set while retaining the programming model of a 32-bit processor. Within the AT91 product hierarchy, the AT91FR40162 combines an embedded processor core with Flash, SRAM, communication peripherals, timers, interrupt control, and external memory interfaces in one integrated circuit. This integration makes it part of the broader embedded-controller and embedded-processing semiconductor category. The device provides 2 MB of Flash for firmware and 256 KB of SRAM for working memory. Its two USART channels support serial peripheral applications, while the three-channel timer/counter supports periodic timing, event counting, and industrial control functions. The ARM7TDMI core operates at 75 MHz and includes an ICE port on dedicated pins, providing a direct target-debug connection without requiring a separate external debug interface adapter. The External Bus Interface allows additional memory or peripheral devices to be connected when the internal resources are insufficient. This architecture is particularly useful in space-constrained embedded systems that need substantial nonvolatile program storage and multiple serial or timing functions without the area required by several discrete components. The 121-ball BGA also supports compact board layouts, although its fine ball pitch requires careful escape routing, inspection, and assembly-process control. Typical uses include industrial controllers, serial gateways, embedded data-acquisition systems, networking equipment, automotive electronics, and compact control modules. Two USARTs can connect sensors or communication transceivers, the three-channel timer/counter can coordinate system events, and the external bus can expand memory or peripheral capacity. The combination of 75 MHz processing, 2 MB Flash, and 256 KB SRAM supports moderately complex control firmware while preserving a deterministic embedded footprint. Board design should prioritize BGA layout quality and bank-aware signal routing. Use the manufacturer pin-description and recommended-layout material when assigning ball positions, and provide stable decoupling close to each supply ball. Firmware development should account for the ARM7TDMI memory map, interrupt priorities, peripheral addressing, and the three-channel timer/counter configuration. Confirm that the selected board library, linker configuration, and development toolchain support the AT91FR40162 device and its 121-ball package. This page consolidates the exact architecture, memory, clock, peripheral, and package characteristics with practical design guidance for industrial control, serial communications, embedded networking, automotive electronics, and data-acquisition designs. It also distinguishes verified same-family drop-in options from unsupported cross-package or functionally similar substitutes.

RFQ پەیوەندی
AT91FR4042-CI - ARM7 75MHz MCU 512KB Flash 121-BGA | Microchip
AT91FR4042-CI

AT91FR4042-CI - ARM7 75MHz MCU 512KB Flash 121-BGA | Microchip

The Microchip Technology AT91FR4042-CI is an ARM7TDMI-based 16/32-bit RISC microcontroller integrating 512 KB of on-chip Flash and 256 KB of on-chip SRAM in a 121-ball BGA (10x10 mm) package. It operates at up to 75 MHz and targets embedded applications that need an external bus interface alongside high-density on-chip memory. An ARM7TDMI microcontroller is a 32-bit RISC processor core licensed by Arm Ltd., combining a 32-bit data path with the 16-bit Thumb instruction set to balance performance and code density. Devices in this family are widely used as general-purpose embedded controllers because they pair deterministic interrupt handling with mature tool support (GCC, IAR, Keil). The AT91 sub-line from Microchip/Atmel extends the core with peripheral blocks such as USARTs, timers, and an external bus interface, placing it in the broader category of embedded microcontrollers -> microprocessors -> semiconductors. Key features of the AT91FR4042-CI include 512 KB (4 Mbits) of reprogrammable program storage, 256 KB (2 Mbits) of SRAM, an external bus interface for off-chip memory or peripherals, two USARTs, a 3-channel timer/counter, a watchdog timer, embedded ICE (in-circuit emulation) debug, and advanced power-saving modes. The combination of large on-chip memory and an external bus removes the need for external SRAM or Flash in many designs, reducing board complexity and BOM cost. The device is fabricated on a low-power CMOS process and runs from a 1.8 V core supply, with separate I/O domain rails. Its MIPS/Watt figure is competitive for the era and the architecture remains popular for legacy industrial and POS designs that need deterministic real-time performance. The embedded ICE block provides non-intrusive debug and Flash programming without external hardware beyond a standard JTAG probe. Typical applications include industrial control, point-of-sale terminals, secure access controllers, HMI panels, and other embedded designs that require 32-bit performance with rich on-chip memory. The 121-BGA package makes it suitable for compact, high-density boards. When designing with the AT91FR4042-CI, ensure the core supply is decoupled with low-ESR ceramic capacitors placed as close as possible to the power balls. The external bus interface requires careful impedance-controlled routing to avoid signal integrity issues at higher bus speeds. This page synthesizes distributor stock, replacement alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ پەیوەندی
AT91FR4042-CI-T - 75MHz ARM7 MCU | Microchip Technology
AT91FR4042-CI-T

AT91FR4042-CI-T - 75MHz ARM7 MCU | Microchip Technology

Microchip Technology AT91FR4042-CI-T is an ARM7-based 16/32-bit microcontroller with a 75 MHz operating frequency, 512 KB of embedded Flash program memory, and 256 KB of RAM. The device is packaged in a 121-ball BGA measuring 10 x 10 mm. Its integrated AT91R40008 ARM Thumb processor and AT49BV4096A 4-Mbit Flash memory die combine the processor, program storage, and associated interface signals in one compact package. A microcontroller is a programmable semiconductor system that integrates a processor core, memory, and peripherals on one die. Within the broader semiconductor hierarchy, this device belongs to the embedded-microcontroller and power-management-IC categories. An embedded microcontroller is commonly used to read inputs, execute control logic, manage communications, and operate actuators without requiring a separate general-purpose computer. The AT91FR4042-CI-T specifically combines an ARM7 processor core with embedded Flash and SRAM in a single 121-ball BGA package. The principal device characteristics visible in the manufacturer documentation are a 75 MHz clock rate, 512 KB of Flash organized as 256K x 16, 256 KB of SRAM organized as 256K x 8, and ARM7 16/32-bit processing. The integrated Flash die is identified as the AT49BV4096A 4-Mbit device. Address, data, and control signals are internally interconnected, with the Flash memory enable treated separately, reducing the external component count required around the processor. The processor implements the ARM Thumb instruction set and supports an ICE debug port on dedicated pins. This architecture combines a 32-bit ARM7 processor core with more compact Thumb code execution, allowing firmware to use the processor efficiently in embedded control systems. The dedicated debug interface also supports target debugging through the ICE port rather than requiring all debug signals to be multiplexed onto general-purpose pins. Typical applications include industrial automation controllers, networked embedded equipment, data-acquisition systems, communication gateways, and compact control platforms that require deterministic real-time behavior. The integrated Flash and SRAM make the device suitable for systems that need resident firmware, working memory, and external peripheral connectivity without separate memory packages. Its 10 x 10 mm BGA footprint is appropriate for multilayer PCB designs with careful ball assignment and controlled manufacturing processes. The principal design consideration is PCB implementation. A 121-ball BGA requires via-in-pad or blind-via structures, adequate solder mask and paste control, and inspection capable of detecting solder-joint defects. Power, clock, ground, and signal routing must follow the pin-description and recommended-layout material in the manufacturer datasheet. Firmware integration should also account for the device’s startup, debug, peripheral, and memory-access behavior before production hardware is released. This product record combines the device’s core architecture, memory organization, package information, application guidance, and documented design constraints. It also separates exact ordering information from procurement actions by directing buyers to the Request a Quote form for current commercial terms and lead-time confirmation.

RFQ پەیوەندی
AT91RM3400-AU - 66MHz ARM7TDMI 256KB ROM MCU | Microchip
AT91RM3400-AU

AT91RM3400-AU - 66MHz ARM7TDMI 256KB ROM MCU | Microchip

The Microchip Technology AT91RM3400-AU is a 16/32-bit ARM7TDMI microcontroller operating at 66 MHz, with 256 KB of ROM and 96 KB of RAM in a 100-pin LQFP package measuring 14 x 14 mm. The device belongs to the AT91SAM family and integrates interfaces including I2C, SPI, SSC, UART/USART, USB, and a multimedia memory card interface. An ARM microcontroller is a programmable system-on-chip built around a licensed processor core, embedded memory, and dedicated peripheral controllers. The ARM7TDMI core combines a 32-bit ARM architecture with Thumb instruction support, allowing compact code to execute in the 16-bit Thumb state while retaining 32-bit processing capability. The AT91RM3400 therefore sits within the hierarchy of embedded microcontroller, embedded processor, and programmable logic device. Three headline characteristics define this part: a 66 MHz ARM7TDMI operating frequency, 256 KB of program ROM, and a broad set of communication peripherals. Its 96 KB SRAM provides working memory for protocol stacks, buffers, and real-time control tasks. The integrated I2C, SPI, SSC, UART/USART, USB, and MMC interfaces reduce external component count and allow the controller to serve as the central communications hub for an embedded board. The part uses the ARM7TDMI architecture with Thumb-2 instruction support for code-density benefits. Its on-chip peripheral set covers serial data exchange, storage-device access, and system monitoring through a watchdog timer. This combination is suited to legacy industrial controllers, communication gateways, data acquisition equipment, and embedded accessories where established ARM7 software support and a mature peripheral set are more valuable than a newer high-performance core. Typical applications include USB-connected control panels, industrial serial bridges, local data concentrators, multimedia card data stores, and compact instrumentation. The 100-LQFP package provides enough pin count for parallel and serial external interfaces while remaining compatible with standard PCB assembly methods. Board designers should route USB differential pairs carefully, provide clean clock and reset networks, and decouple each supply rail close to its supply pins. Design trade-offs center on the 66 MHz ARM7TDMI performance level and the 256 KB ROM footprint. For new designs, confirm that application code, bootloader space, and update requirements fit the available memory before committing the board layout. If substantially greater code space, faster performance, or lower power consumption is required, evaluate a newer microcontroller family and plan a software migration rather than treating a different device as a pin-compatible substitute. This page consolidates core specifications, verified source listings, interface guidance, application fit, and drop-in replacement analysis to support faster component selection and board planning.

RFQ پەیوەندی
AT91RM9200-CJ-002 - ARM920T MCU 180MHz 128KB ROM BGA-256 | Microchip
AT91RM9200-CJ-002

AT91RM9200-CJ-002 - ARM920T MCU 180MHz 128KB ROM BGA-256 | Microchip

The Microchip AT91RM9200-CJ-002 is a complete system-on-chip built around the ARM920T ARM Thumb processor, integrating 128 KB of on-chip ROM, 48 KB of internal SRAM, and a rich set of system and application peripherals in a 256-ball BGA package (15x15 mm). The device operates at up to 180 MHz, delivering 200 MIPS with a memory management unit, 16 KB instruction cache, 16 KB data cache, and write buffer for high-throughput embedded workloads. An ARM920T-based microcontroller is a 16/32-bit RISC microprocessor core that combines the ARM7TDMI integer pipeline with separate instruction and data caches plus a memory management unit, making it suitable for running full operating systems such as Linux or Windows CE. As a product category, this sits within the ARM9 family of application processors, which targets industrial control, networking, and human-machine interface designs that demand deterministic real-time behavior with reasonable power dissipation. The architecture is widely adopted in point-of-sale terminals, building automation, and embedded gateways where deterministic interrupt handling is essential. Key features of the AT91RM9200-CJ-002 include a 10/100 Ethernet MAC with full DMA, a Full Speed USB Host and Device controller, a Multimedia Card Interface, I2S audio, three USARTs, two SPIs (master/slave), a TWI bus, a 16-bit timer/counter, and a real-time clock. The 256-BGA (15x15) industrial-temperature package (-40C to +85C) is suitable for harsh environment designs and is backed by a broad peripheral set that minimizes external glue logic. The device targets core voltage (Vcc) operation from 1.65 V to 1.95 V and includes an internal oscillator, four DMA channels, and an in-circuit emulator with debug communication channel for trace-aware debugging. Power management includes four programmable external interrupt lines, a watchdog timer, and a real-time clock with separate power domain for low-power standby. Typical applications include industrial automation controllers, Ethernet-attached embedded web servers, USB peripherals, building access control, and point-of-sale terminals. The integrated MAC and USB controllers allow single-chip designs that previously required a discrete network or peripheral controller. When designing with this part, plan PCB layout for the 256-ball BGA footprint, ensure 1.65 V-1.95 V core supply decoupling, and verify BGA ball pad pattern against the manufacturer footprint for manufacturability. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet, supporting faster sourcing and BOM risk reduction for AT91RM9200-CJ-002 designs.

RFQ پەیوەندی
AT91RM9200-QU-002 - ARM920T 180MHz MCU | Microchip | Industrial
AT91RM9200-QU-002

AT91RM9200-QU-002 - ARM920T 180MHz MCU | Microchip | Industrial

The Microchip Technology AT91RM9200-QU-002 is a 32-bit ARM920T-based embedded microprocessor running at up to 180 MHz with 128 KB on-chip ROM and 48 KB SRAM, housed in a 208-pin PQFP (28x28 mm) package. It integrates a full-speed USB host and device interface, a 10/100 Ethernet MAC, and a rich peripheral set for embedded control and communication designs. An ARM920T-based embedded microprocessor is a system-on-chip that combines a 32-bit RISC CPU core with memory management, cache, and integrated peripherals on a single die. The AT91RM9200 sits in the hierarchy of ARM9-based microcontrollers, which are themselves a subset of 32-bit embedded processors, which belong to the broader class of microprocessors and microcontrollers used across industrial, networking, and consumer electronics. Key features include a 16 KB instruction cache and 16 KB data cache with write buffer, a memory management unit (MMU) supporting Linux and real-time operating systems, 122 programmable I/O lines, and a supply voltage range of 1.65 V to 1.95 V for the core. The device delivers approximately 200 MIPS at 180 MHz, making it suitable for compute-intensive embedded tasks that require both performance and low power consumption. The AT91RM9200 architecture includes a 16-bit external bus interface, multiple USARTs, master/slave SPI channels, a two-wire interface (TWI), 16-bit timers, an I2S audio interface, and a multimedia card interface (MCI). This peripheral mix enables single-chip solutions for industrial gateways, data loggers, and network appliances without requiring external bridge chips. Typical applications include industrial automation controllers, Ethernet-to-serial gateways, point-of-sale terminals, and embedded Linux systems. The integrated 10/100 Ethernet MAC and USB host/device interfaces reduce BOM cost and board area in networked embedded designs. When designing with the AT91RM9200-QU-002, pay close attention to the 1.8 V core supply decoupling and the 3.3 V I/O rail sequencing. The 208-pin PQFP package requires careful PCB layout to manage the high pin count and maintain signal integrity on the external memory bus. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a single reference for selection and sourcing decisions.

RFQ پەیوەندی