بەرهەمەکان (310+)

SIM7600CE-A - 4G LTE Cat-4 150Mbps Module | SIMCom
SIM7600CE-A

SIM7600CE-A - 4G LTE Cat-4 150Mbps Module | SIMCom

The SIMCom SIM7600CE-A is a 4G LTE Cat-4 wireless module delivering up to 150 Mbps downlink and 50 Mbps uplink, with multi-band TDD-LTE (B38/B39/B40/B41) support and integrated GNSS, housed in a 30 x 30 x 2.9 mm LCC (leadless chip carrier) surface-mount package. A cellular module of this type is a self-contained RF transceiver system that implements the modem baseband, RF front-end, and protocol stack of an LTE network terminal. Within the system hierarchy, it sits between the antenna connector and the host application processor, communicating over AT commands or USB, and forms the connectivity layer of the power management and communications subsystem of an IoT or M2M device. Key features include LTE Cat-4 peak throughput of 150 Mbps downlink / 50 Mbps uplink, backward compatibility with TD-SCDMA (384 Kbps downlink), HSPA+, EVDO, GSM/GPRS/EDGE, and integrated GNSS positioning (GPS + GLONASS + BeiDou). The compact 30 x 30 mm footprint makes it suitable for space-constrained industrial designs requiring both high-speed data and positioning. Technically, the SIM7600 series implements a multi-mode modem supporting LTE-TDD/FDD, TD-SCDMA, CDMA/EVDO, and GSM bands, allowing seamless fallback to 2G/3G networks where LTE coverage is unavailable. Data transfer over USB, UART, and optional audio interfaces enables straightforward integration with microcontrollers and Linux-based hosts via standard AT command sets and dial-up networking. Typical applications include industrial IoT gateways, vehicle tracking and telematics, smart metering backhaul, and security/camera systems that need reliable cellular data plus satellite positioning from a single module. Design consideration: LTE Cat-4 transmitters draw burst currents above 2 A at peak power; the host power supply must provide a stable 3.3-4.2 V rail with low impedance and adequate bulk capacitance to avoid voltage drops during transmit bursts and network registration. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
SIM7600G-H - LTE Cat-4 150Mbps Global 4G GNSS Module | SIMCom
SIM7600G-H

SIM7600G-H - LTE Cat-4 150Mbps Global 4G GNSS Module | SIMCom

The SIMCom SIM7600G-H is a global-band LTE Cat-4 cellular module delivering up to 150 Mbps downlink and 50 Mbps uplink in a 30 x 30 mm LCC surface-mount package, powered from a 3.4 V to 4.2 V supply with 2.3 mA idle current and integrated multi-constellation GNSS (GPS, BeiDou, GLONASS). A cellular module is a self-contained wireless modem that integrates baseband processor, RF transceiver, memory, and power management into a single land-grid-array unit. Within the wireless hierarchy it sits above discrete RF chipsets and below full gateways: host systems (MCU, SBC, or PC) talk to it over USB or UART using AT commands, while the module handles protocol stacks for LTE, WCDMA, and GSM internally. Key features include true global band coverage across LTE-FDD, LTE-TDD, WCDMA/HSPA+, EDGE, and GPRS, so a single PCB design ships to any region. The integrated GNSS receiver with simultaneous cellular-plus-GNSS operation serves trackers and telematics. Interfaces span USB 2.0, UART, I2C, SDMMC, ADC, and PCM voice with DTMF, audio playback, and recording. The module supports multiple built-in network protocols (TCP/IP, HTTP, FTP, MQTT-class stacks) and ships USB drivers for Windows, Linux, and Android, with a mainline Linux option in recent kernels. AT commands are compatible with the SIM7500/SIM7600 family, protecting software investment across variants. Typical applications include vehicle telematics and fleet trackers, industrial IoT gateways, and Raspberry Pi or LattePanda 4G connectivity via popular HAT boards. Critical design point: GSM burst emission draws up to 2 A ripple every 4.615 ms on the VBAT pins, so the supply must deliver more than 2 A with roughly 1000 uF bulk capacitance (or over 300 uF on a 2 A-capable rail) to keep voltage droop under 300 mV. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in family alternatives, and practical power-supply design guidance in one place.

RFQ پەیوەندی
SIM7670E - LTE Cat 1bis 10Mbps GNSS Module | SIMCom | IoT
SIM7670E

SIM7670E - LTE Cat 1bis 10Mbps GNSS Module | SIMCom | IoT

The SIMCom SIM7670E is an LTE Cat 1bis wireless communication module based on the Qualcomm QCX216 chipset that supports LTE-FDD and LTE-TDD modes, delivering up to 10 Mbps downlink and 5 Mbps uplink data rates, with integrated GNSS positioning and a rich protocol stack including MQTT and HTTPS for IoT applications. An LTE Cat 1bis module is a category of cellular IoT modem that achieves LTE data rates using a single receive antenna, unlike Cat 1 with two receivers or Cat M1/NB1 low-power narrowband technologies. Within the wireless connectivity hierarchy, it sits above NB-IoT and Cat M modules in throughput while remaining far more cost-effective than Cat 4 modules, making it a key building block of power management and connectivity subsystems in cellular IoT devices. Key features include the 10 Mbps downlink / 5 Mbps uplink peak data rates enabled by the latest QCX216 chipset, support for both LTE-FDD and LTE-TDD wireless communication modes, integrated GNSS for satellite positioning, and built-in support for IoT application protocols such as MQTT and HTTPS, which reduces host-side firmware complexity. Architecturally, the QCX216 baseband integrates the LTE modem, application processor functions, and GNSS receiver in a single platform, simplifying the RF chain and bill of materials. The single-antenna Cat 1bis RF architecture halves receiver complexity compared with dual-receiver Cat 1, directly lowering module cost while preserving LTE latency and throughput benefits over 2G/3G alternatives. Typical applications include telematics and asset trackers that exploit the GNSS receiver plus LTE uplink, point-of-sale terminals and smart meters that rely on secure MQTT/HTTPS connectivity, and industrial gateways migrating from sunset 2G/3G networks (GSM/GPRS) to LTE, where the module provides a pin-compatible upgrade path from legacy SIM800/SIM7000 designs. A key design consideration is power: LTE Cat 1bis radios draw burst currents during transmission bursts, so the power supply must handle peak current demands with adequate bulk capacitance and a stable supply rail across the specified voltage range. This page synthesizes distributor data, drop-in alternative comparisons, and practical design notes not found in the manufacturer datasheet, with verified sources and freshness dating.

RFQ پەیوەندی
SIM7670G - LTE Cat-1 10Mbps GNSS Module | SIMCom
SIM7670G

SIM7670G - LTE Cat-1 10Mbps GNSS Module | SIMCom

The SIMCom SIM7670G is an LTE Cat-1 wireless communication module with GNSS satellite navigation support, delivering up to 10 Mbps downlink and 5 Mbps uplink data rates in a 24 x 24 mm LCC+LGA form factor. It is built on the Qualcomm QCX216 chipset and supports LTE-FDD and LTE-TDD operation for global (G-region) deployments. An LTE Cat-1 module is a cellular IoT device category defined for machine-type communications that balances moderate data throughput with low cost and wide 4G LTE network coverage. Within the power-management hierarchy of connected devices, cellular modules such as the SIM7670G sit alongside NB-IoT (Cat-M/NB1) modules and full Cat-4 modems, occupying the sweet spot for devices that need several megabits per second, voice capability, and fallback-free LTE-only connectivity as 2G/3G networks sunset worldwide. Key features include Cat-1 peak rates of 10 Mbps DL and 5 Mbps UL, integrated GNSS receiver for positioning alongside cellular data, voice call support, and a supply voltage range of 3.4 V to 4.2 V. Typical quiescent/standby current figures of approximately 3 mA are cited by distributors for comparable SIMCom Cat-1 modules, and the module exposes a rich industrial interface set: UART, USB, I2C, SPI, GPIO, ADC, and SIM card interfaces. Technically, the SIM7670G uses the Qualcomm platform, which distinguishes it from the pin-similar SIMCom A7670X series based on the ASR platform; AT command compatibility across the SIMCom module ecosystem shortens software integration cycles. Embedded network protocol stacks and USB drivers for Windows, Linux, and Android reduce host-side development effort. Typical applications include cellular IoT gateways, vehicle trackers and telematics units, payment terminals, smart metering backhaul, and Raspberry Pi/ESP32-based HAT designs such as the Waveshare SIM7670G LTE Cat-1/GNSS HAT and LilyGo T-SIM7670G-S3. Design consideration: because the module requires a tightly regulated 3.4-4.2 V supply with adequate burst-current headroom during RF transmission, budget the power rail carefully and follow the manufacturer hardware design guide for antenna and keep-out layout. This page synthesizes distributor pricing, regional variant comparisons, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone.

USD $14.77 لە کۆگادایە
SIM7672E - LTE Cat 1bis 10Mbps Module | SIMCom | IoT M2M
SIM7672E

SIM7672E - LTE Cat 1bis 10Mbps Module | SIMCom | IoT M2M

The SIMCom SIM7672E is an LTE Cat 1bis cellular module based on the Qualcomm QCX216 chipset that supports LTE-FDD and LTE-TDD wireless communication modes with a maximum downlink rate of 10Mbps and a maximum uplink rate of 5Mbps, housed in an LCC+LGA form factor package. The E regional variant targets the EMEA (Europe, Middle East, Africa) market with LTE band coverage for those regions. An LTE Cat 1bis module is a category of cellular IoT modem that uses a single antenna (bis = one receive antenna) to deliver Category 1 data rates, positioning it in the hierarchy of cellular connectivity as: Cat 1bis -> LTE Cat 1 -> LTE (4G) -> cellular wide-area network -> wireless communication module. It is widely adopted as the successor technology to 2G (GSM/GPRS) and NB-IoT/Cat M modules for machine-to-machine (M2M) and Internet of Things (IoT) devices that require moderate throughput at low power and low cost. Key differentiating features include the 10Mbps downlink / 5Mbps uplink throughput envelope, the modern QCX216 platform that ensures long-term LTE network longevity, and the LCC+LGA form factor that is pin-compatible by design with SIMCom's A7672 series (Cat 1), SIM7000/SIM7070 series (NB-IoT/Cat M), and SIM800/SIM800F series (2G) modules. This enables a smooth hardware migration path from legacy 2G or NB-IoT products to LTE Cat 1 without a PCB redesign. Technically, the module integrates the cellular baseband, transceiver, RF front end, power management, and a USB 2.0 interface plus UART for host communication, with standard AT command control documented in the SIM76XX Series AT Command Manual. Firmware is updated over USB, and typical host integration uses a microcontroller or application processor driving the UART interface. Typical applications include smart metering, asset trackers and fleet telematics, POS terminals, industrial gateways, security alarm panels, and shared-economy devices such as bike sharing and EV charging stations - use cases that need reliable mid-rate cellular data with multi-year network support. For design-in, pay close attention to power supply design: cellular PA transmit bursts draw high peak currents, so use a low-ESR bulk capacitor near the VBAT pins and follow the reference layout for the antenna feed and grounding to preserve RF performance. This page synthesizes verified datasheet parameters, distributor pricing context, drop-in alternatives within the SIMCom footprint family, and practical design notes not found together in the manufacturer datasheet. Pricing references are as of 2026-10-20.

RFQ پەیوەندی
SIM7672G-MNGV - LTE Cat 1bis 10Mbps Module GNSS | SIMCom
SIM7672G-MNGV

SIM7672G-MNGV - LTE Cat 1bis 10Mbps Module GNSS | SIMCom

The SIMCom SIM7672G-MNGV is an LTE Cat 1bis cellular module with integrated GNSS receiver delivering up to 10 Mbps downlink and 5 Mbps uplink data rates in a compact 24 x 24 x 2.4 mm LCC+LGA surface-mount package. An LTE Cat 1bis module is a category of cellular IoT modem that uses a single receive antenna (bis = one RX chain) to achieve LTE FDD/TDD connectivity at lower cost and power than multi-antenna Cat 4 modules. Cat 1bis sits within the wider LTE category hierarchy of cellular modules, bridging the gap between legacy 2G/GPRS modules such as the SIM800 series and higher-throughput LTE routers, making it the de facto migration path for global 2G/3G sunset designs. Key features include operation on the latest Qualcomm QCX216 chipset, support for LTE-FDD and LTE-TDD wireless modes, worldwide band coverage for global roaming, and form-factor compatibility with the SIMCom A7672 series (Cat 1), SIM7000/SIM7070 series (NB-IoT/Cat M) and SIM800/SIM800F series (2G). This compatibility allows designers to drop the module onto an existing A7672-class land pattern and migrate from 2G, NB-IoT or Cat M products to LTE Cat 1 with minimal PCB rework. Technically, the QCX216 platform integrates the cellular baseband, transceiver and memory in a single chipset, and the G variant adds GNSS (GPS/BeiDou-class satellite positioning) for asset tracking and telematics. Software functions include FOTA (firmware over the air), SSL secure transport, and VoLTE voice support, with AT-command control per the SIM76XX Series AT Command Manual. Typical applications include global-roaming asset trackers, automotive telematics, smart metering, payment terminals, and industrial IoT gateways where LTE longevity matters more than raw throughput. Design consideration: because Cat 1bis uses a single RX chain, throughput falls back gracefully rather than relying on RX diversity - ensure antenna matching and power-supply design follow the SIM7672 hardware design guide for peak-current bursts during LTE transmission. This page synthesizes distributor availability, drop-in family alternatives, design notes, and commercial data not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
SIM800C - Quad-Band GSM/GPRS Module | SIMCom
SIM800C

SIM800C - Quad-Band GSM/GPRS Module | SIMCom

The SIM800C is a complete Quad-Band GSM/GPRS module in a compact LCC (Leadless Chip Carrier) package, designed by SIMCom Wireless Solutions. It operates on 850/900/1800/1900 MHz frequencies and supports GPRS data transfer up to 85.6 kbps. The module measures 17.6 x 15.7 x 2.3 mm, making it suitable for space-constrained IoT and embedded applications. It requires a supply voltage of 3.4V to 4.4V and features a 42-pin SMD interface. A GSM/GPRS module is a cellular communication module that enables devices to connect to GSM networks for voice, SMS, and data services. It integrates a baseband processor, RF transceiver, and power management into a single package, allowing developers to add cellular connectivity to their products without designing complex RF circuitry. The SIM800C sits within the hierarchy of cellular modules, which includes 2G, 3G, 4G LTE, and NB-IoT categories, and is specifically a 2G GSM/GPRS module. Key features of the SIM800C include support for Quad-Band frequencies, GPRS multi-slot class 12, and a rich set of interfaces including UART, USB 2.0, GPIO, SPI, and I2C. It also integrates an audio codec with speaker and microphone amplifiers, making it ideal for voice applications. The module supports AT command control, enabling easy integration with microcontrollers. Its low power consumption in sleep mode (around 1 mA) is beneficial for battery-powered devices. Technically, the SIM800C is built on a mature GSM/GPRS platform, offering reliable performance in 2G networks. It supports SMS, voice calls, and data transmission, with a maximum GPRS downlink speed of 85.6 kbps. The module includes a power management unit that handles over-voltage and under-voltage protection, ensuring safe operation. It also features a PWRKEY pin for power-on/off control and supports normal power-off via AT command 'AT+CPOWD=1'. Typical applications include remote monitoring, asset tracking, alarm systems, smart metering, and IoT gateways. Its compact size and low power consumption make it suitable for portable devices, while its robust interface set allows for flexible system integration. The SIM800C is widely used in industrial and consumer applications where 2G connectivity is still available. When designing with the SIM800C, ensure a stable power supply within 3.4V to 4.4V and adequate decoupling. The module requires a proper antenna connection and careful PCB layout to minimize RF interference. Also, consider the lifecycle status, as 2G networks are being phased out in many regions, which may affect long-term deployment.

RFQ پەیوەندی
SIM800C - Quad-Band GSM/GPRS Module | SIMCom | IoT & M2M
SIM800C

SIM800C - Quad-Band GSM/GPRS Module | SIMCom | IoT & M2M

The SIM800C is a complete Quad-Band GSM/GPRS module in a compact LCC (Leadless Chip Carrier) package, designed by SIMCom Wireless Solutions. It operates on 850/900/1800/1900 MHz frequencies and supports GPRS data transfer up to 85.6 kbps. The module measures only 17.6 x 15.7 x 2.3 mm, making it ideal for space-constrained IoT and M2M applications. It provides a rich set of interfaces including UART, USB 2.0, GPIO, and an audio codec with speaker and microphone amplifiers, enabling voice, SMS, and data communication. A GSM/GPRS module is a self-contained cellular communication device that integrates a baseband processor, RF transceiver, and power management into a single package. It connects to a microcontroller via serial interfaces (typically UART) and communicates using AT commands. The SIM800C sits within the hierarchy: GSM/GPRS module -> cellular module -> wireless communication module -> IoT connectivity component. This modular approach simplifies adding cellular connectivity to embedded systems without requiring deep RF design expertise. Key features of the SIM800C include support for Quad-Band GSM/GPRS (850/900/1800/1900 MHz), GPRS class 12 (up to 85.6 kbps), and a wide operating voltage range of 3.4V to 4.4V. It integrates an audio codec and amplifiers for voice applications, and offers low power consumption in sleep mode (around 1 mA), which is critical for battery-powered IoT devices. The module also supports a variety of network protocols including TCP/IP, UDP, HTTP, and FTP via AT commands, enabling direct internet connectivity. Technically, the SIM800C uses a LCC package with 42 pins, providing excellent thermal and electrical performance. It includes a power management unit that handles over-voltage and under-voltage protection, and supports both normal and abnormal power-off procedures via the PWRKEY pin or AT command AT+CPOWD=1. The module is designed for easy integration with a minimal external component count, requiring only a power supply, SIM card holder, antenna, and a few passive components. Typical applications include remote monitoring and control systems, vehicle tracking devices, smart meters, alarm systems, and portable IoT devices. Its compact size and low power consumption make it suitable for battery-operated devices that need periodic data transmission. The SIM800C is also widely used in development boards and prototyping platforms. When designing with the SIM800C, ensure a stable power supply capable of handling current peaks up to 2A during GSM transmission bursts. Proper PCB layout with adequate grounding and decoupling is essential to maintain RF performance and minimize noise. Also, consider the module's lifecycle status, as it is being phased out in favor of 4G/LTE modules; for new designs, evaluate alternatives like the SIMCom A7683E or SIM7080G.

RFQ پەیوەندی
SIM868 - Quad-Band GSM/GPRS + GNSS Module | SIMCom
SIM868

SIM868 - Quad-Band GSM/GPRS + GNSS Module | SIMCom

The SIMCom SIM868 is a quad-band GSM/GPRS cellular module with integrated GNSS satellite navigation (GPS/GLONASS/BDS), operating from a 3.4V to 4.4V supply with 650 uA idle current, housed in a compact 17.6 x 15.7 mm LCC/LGA surface-mount package. A GSM/GPRS module is a wireless communication subsystem that provides cellular voice, SMS, and packet-switched data connectivity over 2G mobile networks. Within the system hierarchy, it sits between the antenna/RF front end and the host microcontroller, abstracting the cellular protocol stack behind AT commands over UART. Modules such as the SIM868 belong to the broader family of cellular IoT modules, which also includes 3G, 4G/LTE, and LPWA (Cat-M/NB-IoT) devices. Key features include worldwide quad-band operation at 850/900/1800/1900 MHz, GPRS multi-slot class data rates up to 85.6 kbps in both downlink and uplink, and a co-located GNSS receiver supporting GPS, GLONASS, and BeiDou (BDS) constellations for positioning without a second module. The SIM868 integrates abundant extension interfaces: UART, USB 2.0, I2C, GPIO, dual SIM card interfaces, and an SD card interface. The dual-SIM capability is a differentiator versus the earlier SIM808, enabling multi-carrier failover designs. The compact LCC and LGA pad design significantly reduces development time and cost for GNSS-enabled M2M applications, and the module is ROHS compliant. Typical applications include asset tracking, vehicle fleet monitoring, anti-theft systems, and general M2M IoT devices that need both cellular telemetry and satellite positioning in a single footprint. Design considerations: supply the module from a low-impedance 3.4V to 4.4V rail capable of handling GSM transmit burst currents, and verify antenna keep-out areas in the 17.6 x 15.7 mm footprint region. This page synthesizes distributor pricing, availability, drop-in alternative analysis, and design notes not found in the manufacturer datasheet. According to the SIMCom product page, the SIM868 combines a complete quad-band GSM/GPRS engine with GNSS technology for satellite navigation.

RFQ پەیوەندی
SKY66122-11EK1 - 863-928MHz Wi-SUN FEM Eval Board | Skyworks
SKY66122-11EK1

SKY66122-11EK1 - 863-928MHz Wi-SUN FEM Eval Board | Skyworks

The Skyworks Solutions SKY66122-11EK1 is the official evaluation board for the SKY66122-11 high-performance RF front-end module (FEM), tuned for 863 to 915 MHz operation and intended for rapid prototyping of Wi-SUN, ISM-band, and IoT radio designs. An RF front-end module (FEM) evaluation board is a reference PCB that mounts the target RFIC together with the recommended matching network, decoupling, RF connectors, and control interfaces, allowing engineers to measure transmit power, receive sensitivity, and current consumption before committing to a custom layout. In the RF signal-chain hierarchy (evaluation board -> front-end module -> RF transceiver -> wireless node), the SKY66122-11EK1 sits at the top as a measurement and validation vehicle. The underlying SKY66122-11 FEM integrates a power amplifier, a low-noise amplifier (LNA), an RF switch, and a power detector in a single 36-pin MCM (6x6 mm) package. It provides fully matched 50 ohm RF input and output, digital control lines compatible with 1.6 V to 3 V logic, and supports the 863 to 928 MHz high-power ISM band for OFDM modulations such as Wi-SUN. Typical uses include bench characterization of output power and harmonic performance, link-budget validation for sub-GHz mesh networks, firmware development for radio controllers driving the digital control pins, and regulatory pre-scanning in the 863-928 MHz band. When using the board, maintain a clean low-noise supply and calibrate measurements with a calibrated vector signal analyzer to preserve result accuracy. This page synthesizes distributor pricing, datasheet references, and practical evaluation guidance not found in a single manufacturer page.

RFQ پەیوەندی
SKY66409-11 - 2.4 GHz FEM for Zigbee/Thread/BLE | Skyworks
SKY66409-11

SKY66409-11 - 2.4 GHz FEM for Zigbee/Thread/BLE | Skyworks

The Skyworks SKY66409-11 is a high-performance, fully integrated 2.4 GHz RF front-end module (FEM) designed for Zigbee, Thread, and Bluetooth (including Bluetooth Low Energy) applications, housed in a compact 12-ball WLCSP package (1.25 x 1.7 mm). It integrates a power amplifier (PA), low-noise amplifier (LNA), low-loss bypass path, transmit/receive switches, and digital control logic, providing a complete RF front-end solution in a single die. The digital controls are compatible with 1.2 V to 3.6 V logic, allowing direct interfacing with low-power microcontrollers and SoCs. A front-end module (FEM) is a critical subsystem in any wireless transceiver design, sitting between the transceiver IC and the antenna. It amplifies the transmit signal (PA), boosts receive sensitivity (LNA), routes the RF path between TX and RX modes (switches), and optionally bypasses the LNA for power savings. The FEM category sits hierarchically under RF ICs -> wireless transceivers -> RF subsystems, and the SKY66409-11 targets low-power IoT and wearable applications where size, efficiency, and bill-of-material count are critical. Key specifications include integrated TX/RX switching, optimized for +20 dBm output power in Zigbee/Thread modes and Bluetooth/BLE soaks through the PA chain, plus an integrated bypass path that improves RX power consumption when high LNA gain is not required. The 12-ball WLCSP footprint (1.25 x 1.7 mm) makes the part suitable for space-constrained wearables, beacons, and sensor nodes where every square millimeter counts on the PCB. The SKY66409-11 architecture pairs a GaAs/AlGaAs HBT PA with a silicon-on-insulator (SOI) switch/LNA core, providing high efficiency in TX and low noise figure in RX. Digital control inputs (CSD, CTX, CRX, CPSDO, CRSB) eliminate external RF switch driver complexity and enable direct host-microcontroller control. The module is designed for ease of use with minimal external matching, reducing total design cycle time for high-volume IoT products. Typical applications include Zigbee/Thread smart-home hubs and end devices, Bluetooth Low Energy wearables and fitness bands, asset tracking beacons, and Matter-compatible wireless sensor nodes. The wide supply range and low standby current also make it a strong fit for battery-powered devices targeting multi-year coin-cell lifetimes. When designing with the SKY66409-11, follow the Skyworks reference layout to control RF coupling between the PA output and the LNA input. Place the DC control pull-up/down resistors close to the chip balls and use a solid ground plane on layer 2 beneath the WLCSP. Decoupling capacitors must be placed within 1 mm of the supply balls to maintain stable operation across the 1.6 V to 3.6 V supply range. This page synthesizes distributor pricing, datasheet specifications, drop-in alternatives within the same WLCSP footprint, and practical design notes not found in a single source on the manufacturer datasheet.

RFQ پەیوەندی
SR1020AB-MD110-MP1 - UWB Transceiver Module 6-9.3GHz | SPARK Microsystems
SR1020AB-MD110-MP1

SR1020AB-MD110-MP1 - UWB Transceiver Module 6-9.3GHz | SPARK Microsystems

The SPARK Microsystems SR1020AB-MD110-MP1 is an IEEE 802.15.4 Ultra Wideband (UWB) impulse radio RF transceiver module covering the 6 GHz to 9.3 GHz band, with an integrated antenna arrangement and trace connector mounting for flexible integration into host PCBs. It delivers up to 6 Mbps data throughput with an ultra-low-power duty-cycled architecture optimized for battery-powered wireless connectivity. Ultra Wideband impulse radio is a wireless communication technology that transmits data using nanosecond-scale pulses spread over several gigahertz of spectrum, rather than a narrowband modulated carrier. Within the radio hierarchy, the SR1020 sits as a physical-layer transceiver solution under short-range wireless standards (802.15.4 UWB), competing in the same application space as BLE, 802.15.4 Zigbee, and LoRa radios, but offering far lower energy per bit and very low latency. Key differentiating specifications include deep sleep current of just 920 nA and shutdown current of 55 nA, enabling multi-year coin-cell operation under defined use conditions and even energy-harvesting configurations. The active power profile is exceptionally efficient for the 6-9 GHz band: 0.39 mA/Mbps in receive and 0.12 mA/Mbps in transmit at 3.3 V, which is an order of magnitude better energy-per-bit than typical narrowband radios at comparable throughput. The SR1020 architecture aggressively duty-cycles the radio, waking only for short UWB bursts. This yields microsecond-scale synchronization and low-latency links suited to wireless gaming peripherals, true wireless audio, and industrial sensor networks. Data rates from low-kbps telemetry up to 6 Mbps allow a single radio platform to serve both monitoring and streaming use cases. Typical applications include wireless gaming headsets and mice, true wireless earbuds with ultra-low latency, coin-cell IoT sensors, and energy-harvesting industrial nodes where battery replacement is impractical. Design consideration: because UWB performance depends on antenna integration and host-board grounding, follow the SPARK Microsystems reference layout and use the trace connector footprint exactly as specified in the manufacturer datasheet to preserve RF performance and regulatory compliance. This page synthesizes distributor pricing, family alternatives, and practical design guidance not found in the manufacturer datasheet, with pricing data as of 2026-10-20.

RFQ پەیوەندی
ST25DV04K-IER6S3 - 4Kbit Dynamic NFC/RFID Tag IC | STMicroelectronics
ST25DV04K-IER6S3

ST25DV04K-IER6S3 - 4Kbit Dynamic NFC/RFID Tag IC | STMicroelectronics

The ST25DV04K-IER6S3 is a dynamic NFC/RFID tag IC from STMicroelectronics, offering 4 Kbit of EEPROM memory with an I2C interface and an ISO 15693 / ISO 18000-3 Mode 1 compliant RF interface. It operates at 13.56 MHz and supports data rates up to 53 kbit/s in the RF interface, while the I2C interface supports up to 1 MHz. The device is housed in an SO-8 package (NXP-style) and is designed for applications requiring contactless data transfer and configuration, such as smart home devices, industrial equipment, and consumer electronics. Data verified as of 2026-08-05. What is a dynamic NFC/RFID tag IC? A dynamic NFC/RFID tag IC is a type of RFID transponder that combines a contactless RF interface with a wired interface (typically I2C) to allow a microcontroller to read and write the tag's memory both over the air and via the wired bus. This category sits within the broader hierarchy: NFC/RFID tag IC -> RFID transponder -> RFID/NFC integrated circuit -> wireless communication IC -> semiconductor. The dynamic nature means the tag can be updated in real time by the host MCU, enabling use cases like wireless configuration, data logging, and product authentication. Key features include 4 Kbit EEPROM organized in 128-byte pages, an I2C interface with a 1 MHz clock, an RF interface compliant with ISO 15693 and ISO 18000-3 Mode 1, a 64-bit unique identifier (UID), and an energy harvesting function that can power external circuits. The device supports a wide supply voltage range of 1.8V to 5.5V on the I2C side, and it includes an interrupt output to signal RF activity. The SO-8 package is compact and suitable for surface-mount assembly. Technically, the ST25DV04K-IER6S3 integrates an RF front-end with an analog-to-digital converter for energy harvesting, a state machine for protocol handling, and a memory controller for EEPROM access. The EEPROM is organized into 32 pages of 128 bits each, with a data retention of 10 years and an endurance of 1 million write cycles. The device supports both static and dynamic memory mapping, allowing the host to control which memory areas are accessible over RF. Typical applications include smart home devices (e.g., smart locks, thermostats), industrial equipment configuration, consumer electronics pairing (e.g., Bluetooth speakers, wearables), and medical device calibration. The energy harvesting feature enables battery-less operation for low-power sensors, and the I2C interface allows seamless integration with microcontrollers. When designing with this device, ensure proper antenna matching for the RF interface and place decoupling capacitors close to the VCC pin. The energy harvesting output should be buffered with a capacitor to provide stable power to external circuits. Also, consider the I2C address configuration via the RF field to avoid conflicts in multi-tag systems. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing a comprehensive resource for engineers evaluating the ST25DV04K-IER6S3.

USD $0.56 پەیوەندی
ST87M01-1000 - NB-IoT LTE Cat NB2 Module | STMicroelectronics
ST87M01-1000

ST87M01-1000 - NB-IoT LTE Cat NB2 Module | STMicroelectronics

The STMicroelectronics ST87M01-1000 is an ultra-compact, low-power LTE Cat NB2 (NB-IoT) industrial cellular module supporting LTE FDD bands B1, B3, B5, B8, B20 and B28 for worldwide NB-IoT coverage, housed in an LGA package of 10.6 mm x 12.8 mm. It is the variant of the ST87M01 series without the integrated GNSS/Wi-Fi positioning capability, making it the lowest-power and most cost-effective choice for fixed or stationary IoT endpoints. An NB-IoT (Narrowband Internet of Things) module is a low-power wide-area (LPWAN) radio transceiver standardized by 3GPP for LTE Cat NB2. It sits within the broader hierarchy of cellular modules: transceiver -> cellular module -> wireless connectivity IC -> semiconductor device. NB-IoT prioritizes deep indoor penetration, ultra-low standby current and years of battery life over raw throughput, which suits metering, sensing and tracking infrastructure. Key features of the ST87M01 include fully programmable embedded processing, comprehensive worldwide band coverage on a single hardware SKU, and advanced security features per the STMicroelectronics product brief. The ultra-compact LGA footprint facilitates device miniaturization without compromising RF performance, and the industrial-grade design targets long deployment lifetimes. Architecturally, the ST87M01 series integrates the NB-IoT modem, baseband and RF front end into one module, exposing a standard LGA land pattern for direct PCB mounting. The 1.8 V supply domain simplifies power-tree design around common low-voltage batteries and regulators. ST describes it as the first all-in-one module family combining NB-IoT, GNSS and Wi-Fi positioning across its variants; the -1000 SKU provides the cellular function alone. Typical applications include smart electricity, gas and water metering, smart-city infrastructure such as street lighting and parking sensors, industrial condition monitoring, and asset-tracking endpoints where positioning is handled by another means. Design consideration: choose the -1000 variant when GNSS is not required, since the -1001 variant with GNSS capability costs more and consumes additional power; verify antenna keep-out and RF layout per the ST87M01 hardware design guidance. This page synthesizes distributor availability, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
ST87M01-1001 - NB-IoT LTE Cat NB2 Module | STMicroelectronics
ST87M01-1001

ST87M01-1001 - NB-IoT LTE Cat NB2 Module | STMicroelectronics

The STMicroelectronics ST87M01-1001 is an ultra-compact, low-power LTE Cat NB2 NB-IoT industrial cellular module supporting LTE FDD bands B1, B3, B5, B8, B20, and B28, delivering up to +23 dBm transmit output power in a 10.6 mm x 12.8 mm surface-mount LGA package with antenna not included. A cellular IoT module is a wireless communication subsystem that connects embedded devices to operator cellular networks. Within the power-management and connectivity hierarchy, NB-IoT (Narrowband IoT) sits under the LPWAN (Low-Power Wide-Area Network) family of 3GPP LTE standards, which in turn belong to the broader categories of wireless transceivers, RF modules, and industrial IoT communication ICs. NB-IoT modules are optimized for low data rates, deep indoor coverage, and multi-year battery life rather than throughput. Key features of the ST87M01-1001 include comprehensive worldwide band coverage across six LTE FDD bands, ultra-low power consumption of less than 2 uA in low-power mode for multi-year battery operation, and fully programmable architecture allowing customer applications to run on-module. It is a certified LTE Cat NB2 design per the 3GPP release on which it is based, and STMicroelectronics guarantees 15 years of availability, a critical factor for industrial product lifecycles. Technically, the ST87M01 series integrates the cellular modem with advanced security features and industrial-grade design. The -1001 variant provides NB-IoT connectivity plus an extra ADC, while the -1301 and -2301 variants add GNSS and Wi-Fi positioning for combined cellular-plus-location designs. The industrial operating range of -40 C to +85 C supports harsh deployments such as outdoor metering and cold-chain tracking. Typical applications include smart utility metering (electricity, gas, water), asset tracking and telematics, smart city infrastructure such as parking and streetlight control, and industrial sensors on NB-IoT networks. The 868.95 MHz reference in listings relates to adjacent sub-GHz positioning options; the cellular path uses the licensed LTE FDD bands listed above. Design consideration: NB-IoT coverage and SIM/eSIM data plans vary by country and operator, so verify operator NB-IoT support early in the project. Antenna selection and RF layout are also critical because no antenna is included. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet.

RFQ پەیوەندی
ST87M01-1100 - NB-IoT Module with GNSS | STMicroelectronics
ST87M01-1100

ST87M01-1100 - NB-IoT Module with GNSS | STMicroelectronics

The STMicroelectronics ST87M01-1100 is an ultra-compact, low-power LTE Cat NB2 (NB-IoT) industrial module with integrated GNSS/Wi-Fi positioning, certified by Anatel for Brazil and supporting LTE FDD bands B1, B3, B5, B8, B20, and B28. An NB-IoT module is a type of cellular wireless module within the broader family of LPWAN (Low-Power Wide-Area Network) connectivity devices. NB-IoT operates on licensed LTE spectrum and provides deep indoor penetration and long battery life, making it a key building block of power management-aware, battery-operated industrial IoT systems alongside sensors, microcontrollers, and cellular infrastructure. Key features of the ST87M01 family include its all-in-one integration of NB-IoT cellular connectivity, GNSS (GPS/Galileo) satellite positioning, and Wi-Fi 802.11b-based positioning in a single ultra-compact surface-mount package. This eliminates the need for a separate positioning module, reducing BOM count, board area, and integration effort. The family is described by ST as fully programmable, high-performance, and certified, with worldwide band coverage and advanced security features. Technically, the ST87M01 series is an LTE Cat NB2 device, the evolution of 3GPP NB-IoT supporting higher peak data rates than Cat NB1. ST guarantees 15 years of availability for the ST87M01 platform, which is a critical procurement criterion for industrial products with long service lifetimes. Security features are embedded per the manufacturer product page, and the module supports both classic SIM and externally connected eSIM. Typical applications include smart metering, smart street lighting, asset tracking, livestock and agriculture monitoring, and other smart-city verticals - especially in Brazil and other regions using the B1/B3/B5/B8/B20/B28 band set covered by this -1100 region variant. Design consideration: choose the region-specific variant that matches your deployment market and operator certification requirements; ST explicitly directs users to confirm NB-IoT coverage and suitable SIM data plans with their operator before finalizing the design. This page synthesizes manufacturer data, region-variant guidance, drop-in family alternatives, and practical design notes not found on distributor listing pages.

RFQ پەیوەندی
ST87M01-1101 - NB-IoT Module with GNSS | STMicroelectronics
ST87M01-1101

ST87M01-1101 - NB-IoT Module with GNSS | STMicroelectronics

The STMicroelectronics ST87M01-1101 is an ultra-compact, low-power LTE Cat NB2 (NB-IoT) industrial module with integrated GNSS (GPS/Galileo) and Wi-Fi positioning capability plus an extra ADC, supporting LTE FDD frequency bands B1, B3, B5, B8, B20, and B28 for comprehensive worldwide band coverage. An NB-IoT module is a type of cellular LPWAN (Low Power Wide Area Network) transceiver subsystem that sits within the broader hierarchy of wireless connectivity solutions: cellular module, RF transceiver, RF & wireless component. NB-IoT operates on licensed spectrum with deep indoor penetration and carrier-grade security, making it distinct from unlicensed-technologies such as LoRa or Sigfox. Modules like the ST87M01 series integrate the baseband modem, RF front end, power management, and optional positioning engines into a single certified surface-mount unit. The ST87M01-1101 differentiates itself as one of the first all-in-one modules to combine NB-IoT connectivity, GNSS, and Wi-Fi positioning in a single package, eliminating the need for a separate positioning module in asset-tracking designs. Its LTE Cat NB2 compliance enables deployment on 3GPP Release 14 NB-IoT networks, and ST highlights advanced security features and full programmability for industrial applications. The -1101 variant adds GNSS and Wi-Fi positioning plus the additional ADC, and is Anatel-certified for the Brazilian market alongside the ST87M01-1100. Architecturally, the module series is built for ultra-low power consumption, targeting battery-powered endpoints where multi-year battery life is a design requirement. The integrated GNSS receiver supports GPS and Galileo constellations, while the Wi-Fi sniffing capability provides urban positioning where satellite visibility is poor, and the auxiliary ADC allows direct connection of analog sensors without an external converter. Typical applications include asset tracking, smart metering, smart city infrastructure, and battery-powered industrial IoT sensors. In asset trackers, the combination of NB-IoT and GNSS/Wi-Fi positioning in one module reduces BOM count and board area; in metering, the ultra-low-power profile extends battery service intervals. When designing with the ST87M01-1101, verify antenna selection and RF layout against the ST evaluation kit reference design, and confirm the region-specific certification variant matches your target market, since ST ships distinct MPNs for North America (ST87M01-2001/-2301), Brazil (ST87M01-1000/-1100/-1101), and other regions. This page synthesizes distributor listings, the manufacturer datasheet, family-variant cross-references, and pricing context not consolidated in the ST datasheet alone.

RFQ پەیوەندی
ST87M01-2001 - NB-IoT LTE Cat NB2 Module | STMicroelectronics
ST87M01-2001

ST87M01-2001 - NB-IoT LTE Cat NB2 Module | STMicroelectronics

The STMicroelectronics ST87M01-2001 is an ultra-compact, low-power LTE Cat NB2 NB-IoT industrial cellular module from the ST87M01 family, purpose-built for North American markets (USA and Canada regional certification) with Anatel-certified siblings covering Brazil. The -2001 variant provides NB-IoT connectivity only, allowing designers to lower the bill of materials when positioning is not required, while family members such as the ST87M01-2301 add GNSS and Wi-Fi positioning in the same footprint. An NB-IoT (Narrowband Internet of Things) module is a low-power wide-area network (LPWAN) cellular transceiver that operates within licensed spectrum on LTE Category NB2. Within the wireless connectivity hierarchy, NB-IoT modules sit alongside LTE-M and LoRa devices as long-range, low-throughput radios optimized for battery-powered telemetry, smart metering, and asset tracking. The ST87M01 family is positioned as a certified industrial-grade option with multi-band worldwide coverage. Key features of the ST87M01 series include LTE Cat NB2 operation, comprehensive worldwide band coverage, advanced security features, ultra-low power consumption for battery-operated designs, and an ultra-compact surface-mount form factor. According to STMicroelectronics, the family is fully programmable, and ST guarantees 15 years of availability, a critical commitment for industrial product lifecycles. The module integrates the cellular protocol stack in firmware (maintained via the STSW-ST87M01 firmware bundle) and connects to host systems over serial interfaces, with support for both classic SIM cards and externally connected eSIM. The family is programmable, enabling application-level processing on-module rather than on a separate host MCU in some designs. Typical applications include smart utility metering, asset tracking, industrial telemetry, smart city infrastructure, and battery-powered IoT sensor nodes deployed on North American NB-IoT networks. The -2001 variant is the right choice where cellular connectivity alone suffices. Design considerations include verifying operator NB-IoT coverage and SIM data plans for the deployment region, providing an adequate power supply for RF transmit bursts, and following the STDES-ST87M01IGN reference design for antenna and layout guidance. This page synthesizes datasheet information, family cross-references, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
ST87M01-2301 NB-IoT + GNSS/Wi-Fi Module | STMicroelectronics
ST87M01-2301

ST87M01-2301 NB-IoT + GNSS/Wi-Fi Module | STMicroelectronics

The STMicroelectronics ST87M01-2301 is an ultra-compact, low-power LTE Cat NB2 NB-IoT industrial module with integrated GNSS and Wi-Fi positioning plus an extra ADC, supporting LTE FDD frequency bands B2, B4, B5, B12, B13, B66 and B85 for North American networks. A cellular module is a self-contained wireless subassembly that integrates an LTE modem baseband, RF transceiver, front-end, power management and protocol stack on a single surface-mount land pattern, connecting a host microcontroller to operator networks through a simple UART or USB interface. Within the IoT connectivity hierarchy, NB-IoT (Narrowband IoT, standardized by 3GPP as LTE Cat NB2) sits alongside LTE-M as a licensed-spectrum LPWAN technology optimized for low data rates, deep indoor coverage and multi-year battery life. Key differentiating features of the ST87M01-2301 include its all-in-one integration of NB-IoT cellular, GNSS satellite positioning and Wi-Fi positioning - which ST describes as the first such combination in the industry - together with advanced security features and full programmability of the module firmware. The module series is described by STMicroelectronics as high-performance, fully programmable, ultra-compact and low-power, certified for LTE Cat NB2 operation with comprehensive worldwide band coverage. The -2301 variant is region-targeted for the USA and Canada and is certified for those markets, with companion Anatel-certified variants (-1100/-1101) available for Brazil. Typical applications include asset tracking (where GNSS and Wi-Fi positioning remove the need for a separate positioning IC), smart metering, smart-city infrastructure and battery-powered industrial sensors - use cases showcased in the STEVAL-NBIOTV1 evaluation platform and the STDES-ST87M01IGN 2-layer FR4 reference design. Design considerations: NB-IoT coverage and operator support must be confirmed per country, and SIM selection (eSIM or classic SIM, both supported) affects the data plan; RF layout should follow the STDES-ST87M01IGN reference design for antenna matching and power integrity. This page synthesizes datasheet data, family-variant drop-in alternatives, evaluation-tool pairings and pricing references not consolidated in the manufacturer datasheet alone.

RFQ پەیوەندی
STM32WBA5MMGH6TR - Cortex-M33 BLE 5.4/Thread/Zigbee Module | ST
STM32WBA5MMGH6TR

STM32WBA5MMGH6TR - Cortex-M33 BLE 5.4/Thread/Zigbee Module | ST

The STMicroelectronics STM32WBA5MMGH6TR is an ultra-low-power Arm Cortex-M33 TrustZone MCU module integrating Bluetooth LE 5.4, IEEE 802.15.4 (Thread/Zigbee) radio, and 1 Mbyte of Flash memory in a 76-pin LGA module (8 x 12.5 mm). The module runs the Cortex-M33 core at up to 100 MHz with TrustZone security extensions and is designed for connected devices that require multi-protocol 2.4 GHz wireless connectivity without a discrete radio stack on the host MCU. A wireless MCU module combines an application processor, memory, peripherals, and a certified RF subsystem in a single surface-mount land-grid package. In the broader hierarchy, the STM32WBA5MMGH6TR sits under MCU module -> Wireless SoC -> short-range transceiver, where the integrated Cortex-M33 host manages both application code and the radio link layer. This integration eliminates the need for an external radio co-processor, reduces BOM count, and shortens certification time for end products targeting Bluetooth LE, Thread, Zigbee, or Matter ecosystems. Key features of the STM32WBA5MMGH6TR include 1 Mbyte of Flash, up to 100 MHz Cortex-M33 core with TrustZone, Bluetooth LE 5.4 certification-ready radio, integrated 2.4 GHz antenna matching network, and support for Thread/Zigbee via 802.15.4. The module exposes GPIO, I2C, SPI, USART, and ADC peripherals on the LGA pads. Security is enhanced by TrustZone isolation, secure boot, and hardware cryptographic accelerators. Ultra-low-power operation targets always-on battery-powered IoT endpoints. Architecturally, the device pairs an applications Cortex-M33 core with a dedicated 2.4 GHz radio subsystem. The radio chain supports BLE 5.4 (Coded PHY/LE 2M), IEEE 802.15.4 O-QPSK, and proprietary modes. RF matching, balun, and antenna tuning are integrated, removing the need for external RF components. The 76-pin LGA exposes digital I/O, debug (SWD/JTAG), and RF test access, enabling both prototype bring-up and production assembly via standard SMT lines. Typical applications include Bluetooth LE lighting, Matter-over-Thread smart-home devices, Zigbee sensors, BLE wearables, industrial wireless sensor nodes, and asset-tracking beacons. The combination of Cortex-M33 headroom with multi-protocol 2.4 GHz radio makes it well suited to gateways bridging Thread/Zigbee and BLE ecosystems. When designing in the STM32WBA5MMGH6TR, follow ST's recommended PCB footprint and keep the antenna keep-out region clear of copper and plastic. Provide adequate decoupling near the supply pads and verify regulatory compliance for the end device in your target region. This page synthesizes distributor pricing, drop-in STM32WBA module alternatives, and practical PCB/RF layout guidance not consolidated in the ST datasheet alone.

RFQ پەیوەندی
SWA70-CA2A2A1 - WirelessHART Adapter, 4-20mA/HART to Wireless | Endress+Hauser
SWA70-CA2A2A1

SWA70-CA2A2A1 - WirelessHART Adapter, 4-20mA/HART to Wireless | Endress+Hauser

The Endress+Hauser SWA70-CA2A2A1 is a WirelessHART Adapter module from the SWA70 family that wirelessly transmits 4 to 20 mA and HART signals from connected field devices to a WirelessHART Fieldgate (gateway). It functions as an add-on interface module that retrofits wired 4-20 mA/HART instruments with wireless connectivity, powered by either a battery pack or an external power supply unit. The SWA70-CA2A2A1 configuration supports hazardous and non-hazardous area deployments in process automation plants. A WirelessHART Adapter is an industrial wireless interface module that bridges legacy wired HART field instruments onto a WirelessHART mesh network. HART (Highway Addressable Remote Transducer) is the global standard for 4-20 mA smart instrumentation, combining analog signaling with a digital HART protocol. WirelessHART extends this standard to IEC 62591 (HART over IEEE 802.15.4 radio at 2.4 GHz with TDMA mesh), enabling battery-powered wireless monitoring of pressure, temperature, flow, level, and analytical measurements without running new cabling. Key features of the SWA70 WirelessHART Adapter family include dual power options (replaceable battery pack and 24 V DC power supply unit), intrinsic safety variants for hazardous areas, robust IP66/IP67 housing for outdoor mounting, and seamless integration with Endress+Hauser Fieldgate gateways. The adapter retains all HART diagnostic and configuration data while adding wireless transmission, allowing plant operators to extend visibility into remote or hard-to-reach measurement points. Radio output is 10 dBm EIRP typical on the 2.4 GHz ISM band with mesh self-healing routing. The SWA70-CA2A2A1 incorporates industrial-grade EMC and surge protection, conformal-coated electronics, and a wide operating temperature range suitable for chemical, oil & gas, water & wastewater, and power plant environments. Its internal mesh radio (IEEE 802.15.4 PHY, WirelessHART MAC) handles time-synchronized channel hopping, AES-128 encryption, and join/authentication to a WirelessHART network manager. Compared with proprietary wireless sensor networks, WirelessHART interoperability ensures the SWA70 communicates with any IEC 62591-compliant gateway. Typical applications include retrofitting 4-20 mA level gauges in storage tanks, monitoring pressure transmitters along pipelines without trenching signal cables, connecting HART valves and analytical instruments to plant DCS systems, and adding wireless backup to critical measurement loops in chemical plants. Battery-powered operation enables unattended deployment for years, while power-supply operation supports continuous high-update-rate streaming of HART variables including PV, SV, TV, QV and device diagnostics. Design considerations when deploying the SWA70-CA2A2A1 include antenna placement for line-of-sight or near-line-of-sight mesh coverage, calculation of battery life based on update rate (faster updates drain battery quicker), and verification of hazardous-area certification matches the installed zone. The adapter mounts directly on or near the wired HART device with a short stub cable carrying the 4-20 mA loop and HART signal. This page synthesizes distributor pricing, configuration options, and application guidance beyond what the manufacturer's datasheet alone provides, helping engineers select the correct SWA70 option code for their process automation project.

RFQ پەیوەندی
SX1276MB1MAS - LoRa 433/868MHz Mbed Shield | Semtech
SX1276MB1MAS

SX1276MB1MAS - LoRa 433/868MHz Mbed Shield | Semtech

The Semtech SX1276MB1MAS is a LoRa Connect Mbed shield development board featuring the SX1276 sub-GHz LoRa transceiver, configured for the 433 MHz (LF) or 868 MHz (HF) ISM bands, with a U.FL antenna connector (antenna not included) and a through-hole shield form factor. A sub-GHz RF transceiver module is a radio device that transmits and receives data in the license-free frequency bands below 1 GHz. Within the wireless connectivity hierarchy, it belongs to the category of ISM-band transceivers, which sits under RF transceivers, RF and wireless components, and semiconductors. The SX1276 device on this shield implements LoRa (Long Range) spread-spectrum modulation, the leading LPWAN physical-layer technology. Key features include the SX1276 LoRa modem with ultra-long-range spread-spectrum communication, dual-band 433 MHz and 868 MHz configuration, LoRa modulation with high interference immunity, and a standard Mbed-compatible shield format for rapid prototyping with Mbed-enabled microcontroller boards. The U.FL (MHF) connector allows connection of an external antenna matched to the selected band. Technically, the SX1276 integrates the LoRa modem plus a high-performance FSK/OOK modem in a single device, covering 137 MHz to 1020 MHz, with low active and sleep current consumption suited to battery-powered long-range links. The shield exposes the transceiver through the Mbed shield connector (SPI interface), letting developers evaluate LoRa link budgets, range, and modulation settings before committing to a custom PCB. Typical applications include LPWAN node prototyping, smart agriculture and smart city sensor links, industrial telemetry, and long-range IoT gateways in the 433 MHz and 868 MHz ISM bands. Design consideration: always attach a correctly tuned 433 MHz or 868 MHz antenna before transmitting; operating the SX1276 into an unmatched or absent load can stress the PA output stage. This page synthesizes distributor pricing, related-module alternatives, and practical design notes not found in the manufacturer product page. Pricing references are as of 2026-10-19.

RFQ پەیوەندی
T5577 - 125 kHz Read/Write LF RFID IDIC | Microchip Technology
T5577

T5577 - 125 kHz Read/Write LF RFID IDIC | Microchip Technology

The Microchip Technology (formerly Atmel) T5577 (ATA5577C) is a contactless read/write identification IC (IDIC) operating in the 100 to 150 kHz LF RFID band. The T5577 is housed in a wafer-level chip-scale package (WLCSP die), powered and communicated with through a single external coil that doubles as the antenna, energy harvesting element, and bidirectional data interface. The chip integrates 1 kbit of EEPROM organized into blocks plus dedicated config pages, and supports EM4100/EM4200, HID Prox, T5557, and several other 125 kHz protocols via configurable modulation and bit-rate settings. An LF RFID IDIC (Low-Frequency Identification Integrated Circuit) is a passive transponder IC designed for short-range (typically 5–15 cm) contactless identification. The reader/base station energizes the transponder's coil with an RF field; the transponder harvests energy from that field, clock-recovery locks onto the field frequency, and back-scatters or amplitude-modulates its data back to the reader. The 100–150 kHz band is the de-facto standard for legacy access control, animal tagging, parking systems, and hotel locks, balancing coil size against read range. Key features of the T5577 include 100 to 150 kHz carrier compatibility, 1 kbit (128 byte) on-chip EEPROM with block write protection, selectable bit rates and modulation schemes (ASK, FSK, PSK), a 32-bit unique ID, and password-protected write modes. The chip is fully backward-compatible with the T5557/E5551 register map, simplifying migration of legacy T5557 designs. A built-in high-Q antenna tolerance and adaptive resonant capacitor help designers build coils with loose tolerances. Architecturally, the T5577 contains a high-efficiency rectifier, voltage limiter, field-clock recovery block, EEPROM array, modulator, and digital state machine all on a single die. Programming is performed via downlink commands encoded as 100% OOK pulse-interval bit streams, and uplink data is sent back via load modulation (resistive and capacitive options supported). The wide Q-factor tolerance reduces BOM cost because customers can wind coils with less precision. Typical applications include writable access control cards and key fobs, hotel guest-key credentials, parking lot long-range readers, industrial asset tagging, pet/animal identification, laundry and waste-management tokens, and multi-protocol card emulators used by integrators needing EM4100/EM4200/HID compatibility. Compared to a write-locked EM4100, the T5577 trades a single fixed ID for a flexible multi-protocol, password-protected writable credential that can emulate many existing formats from the same silicon. When designing with the T5577, take care to keep the resonant LC tank within the chip's recommended Q range to maximize read distance; a too-high Q narrows bandwidth and reduces data reliability, while a too-low Q wastes energy. Adding a free-wheel rectifier diode and a current-limiting resistor on the coil input is good practice to survive nearby readers operating at full RF power. This page synthesizes verified distributor pricing, multi-protocol feature analysis, and practical design notes that go beyond the manufacturer datasheet's individual parameter tables.

RFQ پەیوەندی
TD1204 - Sigfox/GPS Module with 3D Accelerometer | Telecom Design
TD1204

TD1204 - Sigfox/GPS Module with 3D Accelerometer | Telecom Design

The Telecom Design TD1204 is a high-performance, low-current SIGFOX gateway and GPS receiver module that combines a sub-GHz RF transceiver with a multi-GNSS (GPS/GLONASS) receiver and an integrated ultra-low-power 3D accelerometer, delivered in a compact surface-mount module form factor. It is specified for SIGFOX bidirectional communication in the RCZ1 (868 MHz) band and for multi-GNSS geolocation, with embedded motion and free-fall detection to extend the application range into asset tracking, telematics, and sensor network edge nodes. The module exposes analog and digital interfaces (UART, SPI, I2C, ADC, GPIO) so that any host MCU can interconnect to peripherals with minimal external glue. A SIGFOX module is a pre-certified radio transceiver that implements the SIGFOX ultra-narrow-band (UNB) low-power wide-area network (LPWAN) protocol, allowing battery-powered end devices to transmit short telemetry packets over kilometers of range to base stations. Within the broader wireless hierarchy, SIGFOX sits alongside LoRa and NB-IoT as an LPWAN technology, while GPS represents the global navigation satellite system (GNSS) used for absolute geolocation; the TD1204 fuses both radios in one module to enable asset-tracking applications that need both uplink telemetry and position reporting. Key features include SIGFOX Ready Class 0 certification, integrated multi-GNSS receiver, on-board 3D accelerometer with motion and free-fall interrupts, ARM Cortex-M3 microcontroller core for application firmware, and ultra-low-power sleep modes designed for multi-year battery operation. The wide range of analog and digital interfaces (10-bit ADC, PWM timers, UART/SPI/I2C buses, GPIO) makes it easy to interconnect any external sensor cluster. Typical applications include GPS-tracked asset monitoring (containers, trailers, pallets), fleet management telemetry, livestock and pet trackers, environmental sensor networks, anti-theft vehicle alarms, and remote metering. The combination of SIGFOX uplink, GNSS positioning, and accelerometer-based wake-on-motion allows designers to build event-driven trackers that minimize average power consumption while preserving sub-50 m positional accuracy outdoors. When designing with the TD1204, plan the antenna layout carefully: a tuned 50 ohm trace or chip antenna for 868 MHz plus a separate active or passive GNSS antenna is required. Account for cold-start TTFF (time to first fix) of the GNSS receiver and ensure the host MCU has enough flash for SIGFOX ID, payload codec, and any application-layer encryption. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing, designing in, and qualifying the TD1204.

RFQ پەیوەندی