RF Transceivers
بەرهەمەکان (260+)
RW612HN - Wi-Fi 6 + BLE 5.4 Tri-Radio Wireless MCU | NXP
The NXP Semiconductors RW612HN is a highly integrated, low-power tri-radio wireless MCU combining a 260 MHz Arm Cortex-M33 core with Wi-Fi 6 (802.11ax), Bluetooth Low Energy 5.4, and 802.15.4 radios, housed in a 116-pin VFQFN dual-row exposed-pad package supporting 2.4 GHz and 5 GHz operation. A wireless MCU (microcontroller unit) integrates both a radio transceiver and a processing core on a single die, collapsing what would traditionally require a separate MCU and RF module into one component. Within the power-management and connectivity hierarchy, the RW612 sits above simple BLE-only SoCs and below full application processors, occupying the wireless-system-on-chip (SoC) tier used for connected devices. Key features include tri-radio concurrency (Wi-Fi 6 plus BLE 5.4 plus 802.15.4 for Thread/Zigbee), TrustZone-M hardware security isolation, and 1.2 MB of on-chip SRAM. A Quad SPI interface with high bandwidth and an on-the-fly decryption engine enables secure execute-in-place (XIP) access to off-chip flash and PSRAM, letting designers extend code and data memory cost-effectively. Architecturally, the 260 MHz Cortex-M33 with Armv8-M TrustZone-M provides a root-of-trust foundation, while the integrated Wi-Fi 6 radio delivers 802.11ax efficiency features such as OFDMA and target wake time for lower power and higher network capacity. The RF front end covers 2400 MHz to 2483.5 MHz and 5170 MHz to 5895 MHz per Arrow listings. Typical applications include connected smart home devices, enterprise and industrial automation, smart accessories, and smart energy products where Wi-Fi, Thread/Matter, and BLE coexistence on one chip reduces BOM cost and board area. A key design consideration is RF layout: the dual-row VFQFN exposed pad requires a solid ground pour and via stitching directly beneath the part to ensure RF performance and thermal dissipation. This page synthesizes distributor listings, datasheet links, drop-in alternative analysis, and practical design notes not found in the NXP datasheet alone.
RW612HN-A2IMP - Wi-Fi 6 + BLE 5.4 Tri-Radio MCU | NXP
The NXP RW612HN/A2IMP is a highly integrated, low-power tri-radio wireless MCU combining Wi-Fi 6 (802.11ax), Bluetooth Low Energy 5.4, and 802.15.4 (Thread/Zigbee) radios with a 260 MHz Arm Cortex-M33 core and 1.2 MB on-chip SRAM, housed in a 116-pin VFQFN dual-row exposed-pad package. A wireless MCU (microcontroller unit) is a single-chip device that merges a processor core, memory, peripherals, and one or more radio transceivers, eliminating the need for a separate host processor and radio module. Within the system hierarchy, the RW612 sits at the top of the wireless-SoC category: wireless SoC -> wireless MCU -> microcontroller -> semiconductor, targeting connected-device designs that previously required multi-chip solutions. Key features include the tri-radio concurrent operation (Wi-Fi 6 + BLE 5.4 + 802.15.4), TrustZone-M security isolation, a Quad SPI interface with an on-the-fly decryption engine for secure execute-in-place (XIP) access to off-chip flash and PSRAM, and an operating frequency range of 2.4 GHz to 5 GHz (2400 MHz to 2483.5 MHz and 5170 MHz to 5895 MHz per the Arrow listing). The 260 MHz Cortex-M33 delivers the compute headroom needed for TLS stacks and application logic simultaneously. Technically, the RW61x platform integrates the RF front end, baseband, MAC, and MCU subsystem on one die, reducing BOM count and board area versus discrete radio-plus-host architectures. TrustZone-M partitions secure and non-secure firmware, supporting secure boot and credential storage for Matter and other IoT security frameworks. Typical applications include connected smart home devices, enterprise and industrial automation nodes, smart accessories, gaming controllers, and smart energy endpoints where multi-protocol connectivity is required. Design consideration: the VFQFN dual-row exposed-pad package requires a solid ground pour and thermal via array under the exposed pad for RF and thermal performance; consult the NXP hardware design guide for matching network placement. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.
RYLR896 - LoRa 868/915MHz UART Transceiver Module | REYAX
The REYAX RYLR896 is a LoRa long-range transceiver module operating in the 868/915 MHz ISM bands (frequency coverage 820 MHz to 960 MHz per DigiKey), built around the Semtech SX1276 LoRa engine and controlled entirely through a simple UART interface with AT commands. The module ships with an antenna included and is supplied in a castellated/chassis-mount package suitable for reflow or hand soldering onto a carrier PCB. A LoRa transceiver module is a radio subsystem that implements the LoRa PHY (physical layer) developed by Semtech. LoRa uses chirp spread spectrum (CSS) modulation to achieve link budgets far beyond conventional FSK radios, trading data rate for range and interference immunity. Within a wireless system hierarchy, the module sits between the host MCU and the antenna, providing the complete RF front end, modem, and protocol command layer. Key features include long-range low-power LoRa communication with high interference immunity, a plain AT-command UART interface that removes the need to write SPI register-level drivers for the SX1276, ultra-low current consumption for battery operation, and regulatory certifications including FCC Part 15 Class B compliance documented in the manufacturer datasheet. Technically, the RYLR896 wraps the Semtech SX1276 so that all modem configuration - frequency, spreading factor, bandwidth, coding rate, and power - is set through text commands rather than register writes. The module exposes a minimal pin set: VDD power supply, NRST (active-low reset), RXD, TXD, and GND, as documented in the Zephyr RTOS shield definition for RYLR896/RYLR915. Typical applications include smart agriculture sensor nodes, IoT telemetry and metering, home automation and appliance control over kilometers without internet infrastructure, and industrial monitoring links. Design-wise, keep UART baud rate and supply decoupling per the datasheet, and verify your regional band plan (868 MHz EU vs 915 MHz US) since this module targets the 868/915 MHz variants. This page synthesizes distributor availability, drop-in same-family alternatives, and practical design notes not found in the REYAX datasheet alone.
SAF8444 - 77GHz FMCW Automotive Radar SoC | NXP Semiconductors
The NXP Semiconductors SAF8444 is a 77 GHz automotive FMCW radar system-on-chip (SoC) operating across the 76-81 GHz band, built on 28nm RFCMOS process technology in a compact package for mainstream front and corner radar sensors. An automotive radar SoC is a highly integrated device that combines the RF transceiver front end, radar signal processing, and a microcontroller subsystem on a single die. Within the vehicle sensor hierarchy, it sits at the core of the radar sensor module, upstream of functions such as blind spot detection, automated emergency braking, and L2/L2+ ADAS features, replacing multi-chip discrete radar chains with a single-chip solution. Key features include wideband 76-81 GHz FMCW operation supporting short-, medium-, and long-range sensing, an innovative RF architecture optimized for power efficiency, and advanced interference suppression that improves robustness in dense traffic environments where multiple radar-equipped vehicles operate simultaneously. Technical depth: the SAF8444 is derived from the proven SAF85xx radar platform and fabricated in 28nm RFCMOS. The CMOS-based RF integration simplifies thermal management and reduces system cost compared with SiGe-based radar front ends, and the single-chip integration enables on-sensor L2/L2+ ADAS processing at entry-level vehicle price points. Typical applications include blind spot detection (BSD) corner radar sensors, automated emergency braking (AEB) front radar, and cost-optimized long-range front radar for mainstream and economy EVs, where the power-efficient RFCMOS design reduces cooling requirements in sealed sensor housings. Design consideration: as an automotive-qualified radar SoC, the SAF8444 requires careful antenna-in-package or antenna-on-PCB design and appropriate power sequencing with external flash memory, which is often programmed in-system (as evidenced by dedicated in-system programmers from SMH Technologies). This page synthesizes manufacturer product data, drop-in alternative analysis, and design guidance not found in the manufacturer fact sheet, with pricing references as of 2026-09-14.
SI2434-D-FT - 33.6 kbps ISOmodem | Skyworks Solutions
Skyworks Solutions Inc. SI2434-D-FT is a 33.6 kbps V.34 data ISOmodem system-side integrated circuit designed for data modem and communications equipment. The device supports ITU-T and Bell data modem formats including V.21, V.22, V.23, V.29, V.32, V.32bis, V.34, V.42, V.42bis, V.44, MNP2-5, Fast Connect, and Bell 103 and Bell 212A formats. The SI2434-D-FT is housed in a 24-pin TSSOP package. An ISOmodem is a highly integrated data communications modem controller that combines modem signal processing, line-interface functions, and host-control interfaces into one device. This type of integrated circuit is used within the broader hierarchy of communications semiconductors, specifically in modem ICs and data communications interface controllers. The SI2434-D-FT is intended for system-side implementations where an external host processor controls the modem through UART, SPI, or parallel interfaces. Key features include support for data rates from 300 bps up to 56 kbps, automatic rate negotiation for Type I and Type II caller-ID decoding, and no requirement for external ROM or RAM. The device also supports flexible clocking options, including a low-cost 32.768 kHz oscillator and 4.915 MHz clocking, as described in the Revision D data sheet covering the Si2457, Si2434, Si2415, and Si2404 family. The SI2434-D-FT combines multiple modem formats and negotiation functions in a single controller, reducing the need for separate modulation and protocol blocks. Its system-side architecture allows a host processor to manage configuration, data transfer, and line signaling through the supported serial or parallel control interfaces. This makes the device suitable for embedded telephony, fax, data terminal, modem equipment, and other legacy WAN-access designs. Typical deployments include 33.6 kbps modem systems, V.34 data communication equipment, integrated data/fax modem modules, and telephone-line terminal products. The 24-pin TSSOP package is suitable for compact surface-mount assemblies where a high pin count is required for modem control, clocking, data, and line-interface connections. The principal design consideration is ensuring that the host interface, clock source, line interface, and external analog circuitry are configured according to the manufacturer’s application guidance. Because the SI2434-D-FT is a legacy data-modem controller, system designers should verify the required modem standard, line-side interface, supported clocking method, and package-level land pattern before releasing a new design. The manufacturer data sheet and the component’s pin description should be used to assign the 24 TSSOP connections and to implement the required support circuitry. This product summary consolidates the verified product identity, supported modem formats, package information, and practical use cases into an engineering-focused reference for selecting and integrating the SI2434-D-FT.
SI2494-A-FM - 56 kbps V.92/V.34 ISOMODEM | Skyworks Solutions
The Skyworks Solutions SI2494-A-FM is a 56 kbps V.92 and V.34 ISOMODEM controller/processor IC with Global DAA support, supplied in a 38-pin QFN package measuring 5 x 7 mm. The device is intended for system-side data access arrangements where a telephone-line modem must support legacy V.34 operation alongside V.92 data-rate capability. Its 38-QFN package and exposed-pad construction place the modem controller in a compact surface-mount footprint suitable for communications equipment and embedded access products. An ISOMODEM is an integrated modem chipset solution that combines modem signal processing with telephone-interface functions and associated digital control. Within the broader semiconductor hierarchy, the SI2494-A-FM belongs to the modem controller and network-interface controller class, rather than to a conventional general-purpose microprocessor or standalone analog line transceiver. Its V.34/V.92 support is intended for interoperable data transmission over switched telephone-network and compatible access lines. The SI2494-A-FM is identified as a system-side ISOmodem product and is associated with a 56 kbps data rate. The device family is described in the product documentation as a V.92 and V.34 ISOMODEM with Global DAA, while the 38-pin QFN package is specified as 5 x 7 mm. The exposed-pad package provides a direct thermal path to the PCB and should be connected according to the package land pattern and thermal design guidance. Typical communications uses include centralized modem modules, customer-premises equipment, telephone-line data products, industrial data links, and legacy serial-access systems that require V.92/V.34 interoperability. The controller should be paired with the appropriate line-side interface, isolation barrier, power regulation, crystal or clock network, and host controller required by the end product. Its 56 kbps class is substantially higher than V.34 operation while retaining compatibility with the older modem standard. Design work should begin with the manufacturer’s SI2494/93/57/39/34/15/04 ISOmodem chipset-family guidance. Verify clock, supply sequencing, line-side signaling, exposed-pad soldering, and DAA implementation against the final modem architecture. For an existing board, confirm the 38-QFN 5 x 7 mm footprint, pin functions, thermal pad arrangement, and software compatibility before assigning a replacement role. This page combines package, protocol, compliance, and application information with practical design guidance and a structured comparison framework. It is intended to help engineers identify whether the SI2494-A-FM fits a telephone-data product, understand its integration constraints, and plan a qualified sourcing or replacement review.
SI3015-F-FS - 2.4 kbps V.90 Modem | Silicon Labs | SOIC-16
The Silicon Labs SI3015-F-FS is a 2.4 kbps V.90 modem chipset with ITU V.22bis ISOModem operation, error correction, and an integrated direct access arrangement in a 16-pin SOIC package. The SI3015-F-FS is intended for telephone-line data communication designs that require a compact line-side modem solution. It combines a 2400 bps modem function with a programmable line interface for connection to global telephone-line networks. An ISOModem chipset is a semiconductor implementation of International Telecommunication Union modem recommendations with an integrated line-side interface. In the broader product hierarchy, it belongs to the modem chipset, telecom interface IC, communication semiconductor, and interface IC categories. Its integrated direct access arrangement provides the physical interface between the modem data path and the external telephone network, reducing the amount of surrounding line-interface circuitry required by the host system. The SI3015-F-FS supports 2400 bps modem operation and V.90 data formatting. The associated ISOModem description identifies V.22bis operation with error correction, while the distributor product classification identifies the component as a 2.4 kbps V.90 modem. These features make it relevant to legacy data communications, embedded telephone equipment, remote data access, and industrial modem applications where standardized 2400 bps line communication is required. The device is packaged in a 16-pin SOIC measuring 3.90 mm wide. It is supplied in tube packaging and is identified as lead-free and RoHS-compliant. The SOIC-16 surface-mount format supports conventional PCB assembly while preserving a narrow outline for communication equipment with limited board area. The integrated line interface and standardized modem protocol reduce the functional blocks that the board designer must assemble around the chipset. Typical implementations include telephone-line data terminals, embedded equipment-access modules, industrial remote-monitoring equipment, point-of-sale systems, and legacy telecommunications test equipment. In these systems, the SI3015-F-FS can serve as the line-side modem element while a host processor or communications controller manages the data protocol and higher-level application traffic. Designers should verify the external line-network components, interface timing, isolation strategy, and system grounding against the manufacturer application information before production release. Because the SI3015-F-FS is a complete modem-oriented part rather than a general-purpose serial transceiver, firmware, host-driver, and country-specific telephone-network requirements remain important integration constraints. This page organizes the SI3015-F-FS identification, package information, compliance details, drop-in comparison candidates, and application guidance into an engineering-focused reference. It also highlights which replacement claims can be supported by documented part identities and which electrical or pin-level details still require confirmation from the manufacturer datasheet.
SI4112-D-GM - 1 GHz RF Frequency Synthesizer | Skyworks
The Skyworks Solutions Inc. SI4112-D-GM is a 1 GHz RF frequency synthesizer IC packaged in a 28-VFQFN exposed-pad package. It performs IF and dual-band, low-noise RF frequency synthesis for wireless personal communications while reducing external passive-component requirements and eliminating external VCOs and varactor diodes. The verified product information identifies a 1 GHz synthesis range and a single synthesizer channel. Its integrated approach supports communication equipment requiring accurate local frequency generation while improving power efficiency and reducing board complexity. An RF frequency synthesizer is a timing and frequency-generation IC that derives a stable output from a reference signal. Within the signal-chain hierarchy, the SI4112-D-GM is an RF synthesizer, a phase-locked-loop device, a clock-generation component, and ultimately an RF and wireless semiconductor. Its role is to establish a programmable frequency reference for RF signal paths rather than regulate a power rail or amplify an analog signal. Integrating the synthesis functions reduces the number of external discrete elements required by a communication subsystem. The principal verified features are the 1 GHz maximum synthesizer frequency, 1 GHz synthesis capability, single-channel architecture, 28-VFQFN exposed-pad construction, and RF synthesis function. Skyworks describes the device as addressing price-sensitive, low-power, high-performance personal-wireless requirements by substantially reducing external passive-component count. The exposed pad provides a defined thermal and land-pattern feature in the package, while the compact VFQFN format supports high-density RF board layouts. The device family is associated with IF and dual-band RF synthesis, making it relevant to wireless personal communications, RF transceivers, frequency-generation modules, and communication test equipment. Because the supplied sources do not provide complete operating-voltage, reference-input, output-power, phase-noise, temperature, or control-interface values, those specifications are intentionally not inferred. Engineers should consult the manufacturer datasheet and evaluate the complete electrical and pin-level requirements before releasing a production design. Typical design use places the SI4112-D-GM in the frequency-generation section of an RF communication system. Its integrated synthesizer reduces external VCO and varactor requirements, which can shorten RF layout effort and lower component count compared with a discrete implementation. The 28-VFQFN exposed-pad package still requires careful thermal-via layout and short, controlled RF interconnects to preserve intended performance. The key implementation consideration is package and RF layout validation. Place the device according to the manufacturer land pattern, provide the specified reference and decoupling connections, and verify exposed-pad soldering and thermal-via density. Do not substitute a 24-TSSOP part such as SI4112-D-GT for this VFQFN device without a complete mechanical and pin-level review. This product page consolidates the verified Skyworks and distributor information, distinguishes the VFQGN device from differently packaged family members, and highlights practical RF layout considerations that are not apparent from a basic distributor listing.
SI4112-D-GMR - 1 GHz RF Frequency Synthesizer | Skyworks (Tape & Reel)
The Skyworks Solutions Inc. SI4112-D-GMR is a 1 GHz RF frequency synthesizer IC packaged in a 28-VFQFN exposed-pad package. It performs IF and dual-band, low-noise RF frequency synthesis for wireless personal communications while reducing external passive-component requirements and eliminating external VCOs and varactor diodes. The verified product information identifies a 1 GHz synthesis range and a single synthesizer channel. Its integrated approach supports communication equipment requiring accurate local frequency generation while improving power efficiency and reducing board complexity. An RF frequency synthesizer is a timing and frequency-generation IC that derives a stable output from a reference signal. Within the signal-chain hierarchy, the SI4112-D-GMR is an RF synthesizer, a phase-locked-loop device, a clock-generation component, and ultimately an RF and wireless semiconductor. Its role is to establish a programmable frequency reference for RF signal paths rather than regulate a power rail or amplify an analog signal. Integrating the synthesis functions reduces the number of external discrete elements required by a communication subsystem. The principal verified features are the 1 GHz maximum synthesizer frequency, 1 GHz synthesis capability, single-channel architecture, 28-VFQFN exposed-pad construction, and RF synthesis function. Skyworks describes the device as addressing price-sensitive, low-power, high-performance personal-wireless requirements by substantially reducing external passive-component count. The exposed pad provides a defined thermal and land-pattern feature in the package, while the compact VFQFN format supports high-density RF board layouts. The device family is associated with IF and dual-band RF synthesis, making it relevant to wireless personal communications, RF transceivers, frequency-generation modules, and communication test equipment. Because the supplied sources do not provide complete operating-voltage, reference-input, output-power, phase-noise, temperature, or control-interface values, those specifications are intentionally not inferred. Engineers should consult the manufacturer datasheet and evaluate the complete electrical and pin-level requirements before releasing a production design. Typical design use places the SI4112-D-GMR in the frequency-generation section of an RF communication system. Its integrated synthesizer reduces external VCO and varactor requirements, which can shorten RF layout effort and lower component count compared with a discrete implementation. The 28-VFQFN exposed-pad package still requires careful thermal-via layout and short, controlled RF interconnects to preserve intended performance. The key implementation consideration is package and RF layout validation. Place the device according to the manufacturer land pattern, provide the specified reference and decoupling connections, and verify exposed-pad soldering and thermal-via density. Do not substitute a 24-TSSOP part such as SI4112-D-GT for this VFQFN device without a complete mechanical and pin-level review. This product page consolidates the verified Skyworks and distributor information, distinguishes the VFQGN device from differently packaged family members, and highlights practical RF layout considerations that are not apparent from a basic distributor listing.
SI4123-D-GM - Dual-Band RF Synthesizer | Skyworks
Skyworks Solutions SI4123-D-GM is a dual-band RF frequency synthesizer with integrated VCOs for wireless personal communications, covering intermediate-frequency and dual-band synthesis requirements. According to the retrieved product listing, it operates from 2.7 V to 3.6 V, supports frequency ranges of 900 MHz to 1800 MHz and 750 MHz to 1500 MHz, and provides output power from -14 dBm to +1 dBm. The device is associated with a 28-pin VFQFN exposed-pad package in the supplied cross-reference data. A frequency synthesizer generates a stable, programmable output signal by combining a phase-locked loop with a voltage-controlled oscillator. An RF synthesizer extends this function into the radio-frequency domain and is used to establish carrier or intermediate-frequency signals in wireless receivers, transmitters, and related communication equipment. The SI4123 family is positioned as a low-power, price-sensitive solution for personal wireless communications. The SI4123-D-GM integrates the VCO functions, which the Skyworks product description says reduces the external passive-component count and eliminates external VCOs and varactor diodes. This integration can simplify RF board layouts and reduce assembly requirements. Its dual-band capability allows one device family to address multiple wireless frequency plans, while programmable synthesis gives system designers flexibility in setting the generated frequency. Typical wireless communication uses include RF front-end signal generation, intermediate-frequency synthesis, and dual-band transceiver support. The 2.7 V to 3.6 V supply range is suitable for low-voltage RF systems, while the listed 18 mA to 27 mA current range should be checked against the actual operating mode and frequency plan. The exposed-pad package also requires attention to PCB thermal dissipation and layout quality. Designers should follow the manufacturer datasheet for the complete pinout, recommended loop-filter components, reference-clock requirements, RF output matching network, and decoupling layout. The available search results identify the device as obsolete or associated with an obsolete product status in comparison pages, so lifecycle confirmation should be completed before new production sourcing. This page consolidates verified distributor results, cross-reference findings, package information, application context, and engineering cautions.
SI4123-D-GMR - Dual-Band RF Synthesizer | Skyworks (Tape & Reel)
Skyworks Solutions SI4123-D-GMR is a dual-band RF frequency synthesizer with integrated VCOs for wireless personal communications, covering intermediate-frequency and dual-band synthesis requirements. According to the retrieved product listing, it operates from 2.7 V to 3.6 V, supports frequency ranges of 900 MHz to 1800 MHz and 750 MHz to 1500 MHz, and provides output power from -14 dBm to +1 dBm. The device is associated with a 28-pin VFQFN exposed-pad package in the supplied cross-reference data. A frequency synthesizer generates a stable, programmable output signal by combining a phase-locked loop with a voltage-controlled oscillator. An RF synthesizer extends this function into the radio-frequency domain and is used to establish carrier or intermediate-frequency signals in wireless receivers, transmitters, and related communication equipment. The SI4123 family is positioned as a low-power, price-sensitive solution for personal wireless communications. The SI4123-D-GMR integrates the VCO functions, which the Skyworks product description says reduces the external passive-component count and eliminates external VCOs and varactor diodes. This integration can simplify RF board layouts and reduce assembly requirements. Its dual-band capability allows one device family to address multiple wireless frequency plans, while programmable synthesis gives system designers flexibility in setting the generated frequency. Typical wireless communication uses include RF front-end signal generation, intermediate-frequency synthesis, and dual-band transceiver support. The 2.7 V to 3.6 V supply range is suitable for low-voltage RF systems, while the listed 18 mA to 27 mA current range should be checked against the actual operating mode and frequency plan. The exposed-pad package also requires attention to PCB thermal dissipation and layout quality. Designers should follow the manufacturer datasheet for the complete pinout, recommended loop-filter components, reference-clock requirements, RF output matching network, and decoupling layout. The available search results identify the device as obsolete or associated with an obsolete product status in comparison pages, so lifecycle confirmation should be completed before new production sourcing. This page consolidates verified distributor results, cross-reference findings, package information, application context, and engineering cautions.
SI4126-F-BM - 2.3 GHz RF Synthesizer | Skyworks
The Skyworks Solutions SI4126-F-BM is a frequency-synthesizer IC with a maximum stated frequency of 2.3 GHz, one RF output, and a 28-pin VQFN exposed-pad package. The verified distributor listing identifies it as an RF synthesizer for clock-generation, PLL, and wireless-communications applications, while the available historical family description identifies integrated VCOs, loop filters, reference dividers, VCO dividers, and phase detectors. A frequency synthesizer is a timing and RF signal-generation component that uses a phase-locked loop to create an output frequency referenced to a stable external source. In the wireless-communications hierarchy, this device belongs to RF and wireless clock and timing ICs rather than a general-purpose clock generator. Its PLL-based architecture supports programmable frequency synthesis for RF and IF signal paths. The verified data specifies a 2.3 GHz maximum frequency, one RF output, a 2.7 V to 3.6 V operating supply range as stated in the available product overview, and a 28-VFQFN exposed-pad package. The family-level description also reports low phase noise and minimal external-component requirements. These characteristics make the part relevant to compact RF systems where local frequency generation is needed instead of a fixed-frequency oscillator. The SI4136-family architecture uses three VCOs, loop filters, reference and VCO dividers, and phase detectors, with divider and power-down settings programmable through a three-wire serial interface. The available source material describes dual-band RF synthesis and integration of VCOs, loop filters, varactors, and resonators, reducing the number of discrete frequency-generation components required around the IC. Typical use cases include wireless transceivers, RF modems, ISM-band equipment, IF/RF synthesis, and embedded radio systems. The part may also be considered for test equipment or communication modules requiring a programmable RF reference. Final suitability depends on the required output frequency, reference input, loop-filter implementation, supply sequencing, and board-level RF layout. Designers should follow the manufacturer datasheet for the exact pin assignments, recommended reference components, VCO configuration, exposed-pad land pattern, and decoupling network. Because the verified material does not provide a complete electrical table or an explicit package-body drawing in the supplied fields, parameters such as phase-noise profiles, output power, temperature range, and absolute maximum ratings require confirmation from the manufacturer documentation. This product page consolidates the verified distributor specifications, source URLs, package identity, and design caveats so engineers can distinguish a genuine RF synthesizer replacement from a merely similar clock or PLL component.
SI4126-F-BMR - 2.3 GHz RF Synthesizer | Skyworks (Tape & Reel)
The Skyworks Solutions SI4126-F-BMR is a frequency-synthesizer IC with a maximum stated frequency of 2.3 GHz, one RF output, and a 28-pin VQFN exposed-pad package. The verified distributor listing identifies it as an RF synthesizer for clock-generation, PLL, and wireless-communications applications, while the available historical family description identifies integrated VCOs, loop filters, reference dividers, VCO dividers, and phase detectors. A frequency synthesizer is a timing and RF signal-generation component that uses a phase-locked loop to create an output frequency referenced to a stable external source. In the wireless-communications hierarchy, this device belongs to RF and wireless clock and timing ICs rather than a general-purpose clock generator. Its PLL-based architecture supports programmable frequency synthesis for RF and IF signal paths. The verified data specifies a 2.3 GHz maximum frequency, one RF output, a 2.7 V to 3.6 V operating supply range as stated in the available product overview, and a 28-VFQFN exposed-pad package. The family-level description also reports low phase noise and minimal external-component requirements. These characteristics make the part relevant to compact RF systems where local frequency generation is needed instead of a fixed-frequency oscillator. The SI4136-family architecture uses three VCOs, loop filters, reference and VCO dividers, and phase detectors, with divider and power-down settings programmable through a three-wire serial interface. The available source material describes dual-band RF synthesis and integration of VCOs, loop filters, varactors, and resonators, reducing the number of discrete frequency-generation components required around the IC. Typical use cases include wireless transceivers, RF modems, ISM-band equipment, IF/RF synthesis, and embedded radio systems. The part may also be considered for test equipment or communication modules requiring a programmable RF reference. Final suitability depends on the required output frequency, reference input, loop-filter implementation, supply sequencing, and board-level RF layout. Designers should follow the manufacturer datasheet for the exact pin assignments, recommended reference components, VCO configuration, exposed-pad land pattern, and decoupling network. Because the verified material does not provide a complete electrical table or an explicit package-body drawing in the supplied fields, parameters such as phase-noise profiles, output power, temperature range, and absolute maximum ratings require confirmation from the manufacturer documentation. This product page consolidates the verified distributor specifications, source URLs, package identity, and design caveats so engineers can distinguish a genuine RF synthesizer replacement from a merely similar clock or PLL component.
SI4136-F-GT - 2.5 GHz RF Synthesizer | Silicon Labs
The Silicon Labs SI4136-F-GT is a monolithic ISM RF synthesizer IC with three integrated voltage-controlled oscillators, loop filters, reference and VCO dividers, and phase detectors. It supports RF synthesis for wireless communications and is identified with a 2.5 GHz maximum frequency in distributor listings. The device is packaged in a 24-TSSOP measuring 0.173 inch, or 4.40 mm, in width. An RF frequency synthesizer generates a stable, programmable output from a reference frequency by comparing a divided output with a divided reference and correcting the VCO through a feedback loop. In the Si4136, three integrated VCOs, resonators, varactors, loop filters, phase detectors, and programmable dividers reduce the number of external RF components required. This integration is useful when a wireless product needs both IF and RF synthesis from one IC. Verified feature data identifies low phase noise, minimal external-component requirements, a 5 µA standby current, and a 25.7 mA typical supply current. A three-wire serial interface programs divider and power-down settings. The 2.5 GHz capability makes the part applicable to ISM wireless transmitters, receivers, WLAN radio designs, and other RF communication equipment, provided the selected output frequency and channel plan fall within the device's specified operating limits. The 24-TSSOP package is designed for surface-mount PCB assembly, but RF performance depends on controlled grounding, short supply connections, clean reference routing, and careful output matching. Power-supply decoupling and loop-filter layout should follow the manufacturer datasheet and reference-circuit recommendations. The integrated synthesizer simplifies BOM size, yet PCB parasitics, reference jitter, antenna coupling, and thermal conditions can still affect phase noise and lock behavior. This page consolidates the verified distributor description, package information, feature snippets, pricing evidence, and cross-reference search results for SI4136-F-GT. It also distinguishes verified drop-in alternatives from unsupported replacements; no cross-brand drop-in equivalent was established by the supplied data. Designers should verify the complete electrical limits, register map, pin names, and reference configuration in the applicable manufacturer datasheet before release. Especially, the product is a frequency synthesizer rather than a complete RF transceiver, and its performance must be evaluated together with the external reference, matching network, antenna path, and system power architecture.
SI4136-F-GTR - 2.5 GHz RF Synthesizer | Silicon Labs (Tape & Reel)
The Silicon Labs SI4136-F-GTR is a monolithic ISM RF synthesizer IC with three integrated voltage-controlled oscillators, loop filters, reference and VCO dividers, and phase detectors. It supports RF synthesis for wireless communications and is identified with a 2.5 GHz maximum frequency in distributor listings. The device is packaged in a 24-TSSOP measuring 0.173 inch, or 4.40 mm, in width. An RF frequency synthesizer generates a stable, programmable output from a reference frequency by comparing a divided output with a divided reference and correcting the VCO through a feedback loop. In the Si4136, three integrated VCOs, resonators, varactors, loop filters, phase detectors, and programmable dividers reduce the number of external RF components required. This integration is useful when a wireless product needs both IF and RF synthesis from one IC. Verified feature data identifies low phase noise, minimal external-component requirements, a 5 µA standby current, and a 25.7 mA typical supply current. A three-wire serial interface programs divider and power-down settings. The 2.5 GHz capability makes the part applicable to ISM wireless transmitters, receivers, WLAN radio designs, and other RF communication equipment, provided the selected output frequency and channel plan fall within the device's specified operating limits. The 24-TSSOP package is designed for surface-mount PCB assembly, but RF performance depends on controlled grounding, short supply connections, clean reference routing, and careful output matching. Power-supply decoupling and loop-filter layout should follow the manufacturer datasheet and reference-circuit recommendations. The integrated synthesizer simplifies BOM size, yet PCB parasitics, reference jitter, antenna coupling, and thermal conditions can still affect phase noise and lock behavior. This page consolidates the verified distributor description, package information, feature snippets, pricing evidence, and cross-reference search results for SI4136-F-GTR. It also distinguishes verified drop-in alternatives from unsupported replacements; no cross-brand drop-in equivalent was established by the supplied data. Designers should verify the complete electrical limits, register map, pin names, and reference configuration in the applicable manufacturer datasheet before release. Especially, the product is a frequency synthesizer rather than a complete RF transceiver, and its performance must be evaluated together with the external reference, matching network, antenna path, and system power architecture.
SIM7000G - Cat-M/NB-IoT/GPRS/GNSS LPWA Module | SIMCom
The SIMCom SIM7000G is a multi-band LPWA cellular module supporting LTE Cat-M, NB-IoT, GPRS and EDGE on 850 MHz, 900 MHz, 1800 MHz and 1900 MHz bands, with an integrated GNSS receiver, housed in a 24 mm x 24 mm LCC surface-mount package supplied from 3.0 V to 4.3 V. An LPWA (Low Power Wide Area) module is a type of cellular transceiver optimized for low-latency, low-throughput machine-to-machine communication rather than bandwidth. Within the wireless hierarchy - transceiver, RF module, cellular modem, IoT connectivity layer - LPWA modules like the SIM7000G bridge battery-powered sensors to carrier networks over Cat-M (LTE-M), NB-IoT (Cat-NB), and the legacy 2G GPRS/EDGE fallback used where LTE coverage is unavailable. Key features include Power Save Mode (PSM) and extended Discontinuous Reception (eDRX) that enable battery life of up to 10 years, deep coverage enhancement relative to GSM, and abundant interfaces: UART, USB, GPIO, I2C, ADC, PCM, and SIM card. The integrated GNSS receiver provides positioning without a separate GPS module, reducing BOM cost and board area. Technically, the SIM7000 series is designed for varied radio propagation conditions, and the G variant is the global/regional-frequency version covering B1, B2, B3, B4 and additional bands per SIMCom documentation. The 24x24 mm LCC castellation footprint is pad-compatible with the SIM900/SIM800F footprint, and AT command sets are largely compatible with SIM800F, easing migration from 2G designs. Typical applications include smart metering, asset tracking, smart parking, smart city sensors, and industrial M2M telemetry - all scenarios where low data volume, deep indoor coverage, and multi-year battery life dominate. Design consideration: supply the module from a 3.3 V to 4.2 V source (Li-ion directly or a buck regulator) with low-ripple capability, since cellular TX bursts draw significant peak current; a single Li-ion cell within the 3.0 V to 4.3 V window is the standard approach. This page synthesizes distributor pricing, drop-in SIM7000-family alternatives, and practical design notes not consolidated in the manufacturer datasheet.
SIM7070G - Cat-M/NB-IoT/GSM GNSS IoT Module | SIMCom
The SIMCom SIM7070G is a multi-band cellular IoT transceiver module supporting LTE Cat-M (Cat-M1), NB-IoT (Cat-NB2) and GSM/GPRS with integrated GNSS (GPS/GLONASS/Galileo/BeiDou) satellite navigation, operating in the 850 MHz, 900 MHz, 1800 MHz and 1900 MHz bands and supplied as a surface-mount module without antenna. A cellular IoT module is a self-contained wireless transceiver that integrates a baseband processor, RF front end, power management and protocol stacks (TCP/IP, UDP, FTP, HTTP, MQTT) into a single LGA footprint. Within the system hierarchy, it sits above the antenna and below the host microcontroller, communicating via AT commands or USB to give any embedded system wide-area network connectivity without the designer handling RF certification directly. Key features include tri-mode fallback (Cat-M to NB-IoT to GSM) for global coverage, integrated GNSS receiver eliminating a separate GPS module, and Power Saving Mode (PSM) plus extended Discontinuous Reception (eDRX) that can extend battery life up to 10 years, according to SIMCom product documentation. Deep coverage enhancement versus legacy GSM improves link margin in basements and rural deployments. The SIM7070 series shares its form factor and AT command set with the SIM7000X/SIM800F/SIM900 families, enabling migration of legacy 2G designs to LPWA networks with minimal firmware changes. Data rates suit telemetry workloads rather than broadband: NB-IoT/Cat-M throughput is sufficient for MQTT messaging, fleet reporting and OTA configuration. The module runs the ThreadX RTOS per SIMCom user guides. Typical applications include asset tracking with GNSS positioning, smart utility metering, fleet telematics and battery-powered sensor nodes where multi-year battery life and carrier fallback between LTE-M, NB-IoT and 2G networks are required. Design consideration: the module is not pin-for-pin identical to the SIM800F; verify the hardware design guide (SIM7070G Hardware Design) for power supply sequencing, since peak transmit currents on GSM demand a low-ESR supply with adequate bulk capacitance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
SR1010AB-MD150-MP1 - UWB Transceiver Module 3.1-5.8GHz | SPARK Microsystems
The SPARK Microsystems SR1010AB-MD150-MP1 is an 802.15.4 Ultra Wideband (UWB) impulse radio transceiver module operating across the 3.1 GHz to 5.8 GHz frequency band, with an integrated trace antenna and a connector mount form factor for flexible host-board integration. An ultra wideband transceiver module is a complete radio subsystem that transmits data using extremely short, low-power pulses spread across a very wide spectrum. In the RF hierarchy, a UWB module sits within the broader categories of RF transceivers, short-range wireless communication systems, and RF modules. UWB technology enables precise ranging and high data-rate links with very low energy per bit, which is why it has become the preferred physical layer for indoor positioning, secure keyless entry, and low-power wireless sensor networks. Key features of this module include IEEE 802.15.4 UWB impulse radio compliance, coverage of the full 3.1 GHz to 5.8 GHz UWB band, and an integrated trace antenna that eliminates the need for external antenna design and RF matching work. According to the SPARK Microsystems product highlight on DigiKey, the SR1010AB-MD150-MP1 and its sibling SR1020AB-MD110-MP1 are characterized by ultra-low power consumption, which directly extends battery life in portable and IoT devices. The SPARK Microsystems SR1010 transceiver family is built around SPARK's proprietary impulse radio architecture, which achieves efficient wake-and-transmit cycles rather than continuous carrier operation. This makes the module particularly suited to applications where average current draw, not peak throughput, dominates the power budget. The integrated antenna design also shortens time-to-market because the RF section is pre-certified and pre-matched at the module level. Typical applications include asset tracking and indoor positioning systems, wireless sensor networks for industrial monitoring, and low-latency gaming or wearable links where milliwatt-scale average power matters. The connector mount form factor allows prototyping and production integration without soldering the module directly onto the main PCB. Designers should account for antenna keep-out and ground clearance around the module's integrated trace antenna, and verify regulatory channel selection within the 3.1 GHz to 5.8 GHz band for the target region. This page synthesizes distributor pricing, family alternatives, and practical design notes not found in the manufacturer datasheet, with prices verified as of 2026-10-20.
ST25R3916B - NFC Initiator with 1.4W Power | STMicroelectronics
The ST25R3916B is a highly integrated NFC initiator and card emulator from STMicroelectronics, designed for high-performance contactless communication. It supports ISO 14443A/B, ISO 15693, and FeliCa protocols, delivering up to 1.4W of output power for extended read range. The device operates from a 2.4V to 5.5V supply and is available in a 32-pin VFQFPN package. An NFC initiator is a device that actively generates an RF field to communicate with passive tags or cards. It is the core component in applications such as point-of-sale terminals, access control readers, and NFC-enabled consumer electronics. The ST25R3916B sits within the NFC reader IC family, which is part of the broader RFID and contactless communication IC category, ultimately falling under wireless communication semiconductors. Key features include a built-in high-efficiency power amplifier that delivers up to 1.4W, dynamic power control for optimal field strength, and advanced anti-collision algorithms for reliable multi-tag reading. The device also integrates a low-power card detection mode, making it suitable for battery-powered applications. Its high sensitivity and noise immunity ensure robust performance in noisy environments. The ST25R3916B employs a sophisticated analog front-end with automatic antenna tuning and calibration, simplifying PCB design and reducing component count. It supports both active and passive load modulation, enabling card emulation and peer-to-peer modes. The device includes a comprehensive set of registers for fine-tuning RF parameters, allowing designers to optimize performance for specific antenna configurations. Typical applications include payment terminals, access control systems, NFC-enabled smart locks, and industrial RFID readers. The high output power extends read range, while the low-power modes preserve battery life in portable devices. The device is also suitable for automotive key fobs and in-vehicle NFC modules. When designing with the ST25R3916B, careful attention must be paid to antenna matching and power supply decoupling. The device requires a clean supply voltage and proper grounding to achieve optimal RF performance. The SPI interface allows easy integration with microcontrollers, and the interrupt output simplifies event-driven firmware design.
ST25R3920B - NFC Reader IC, 13.56MHz, ISO 14443A/B | STMicroelectronics
The ST25R3920B is a high-performance NFC universal reader IC from STMicroelectronics, designed for 13.56 MHz contactless communication. It supports ISO 14443A/B, ISO 15693, and FeliCa protocols, making it a versatile solution for a wide range of NFC applications. The device operates from a 2.4V to 5.5V supply and features an integrated high-power transmitter with programmable output power up to 1.4W, enabling robust communication with passive tags and cards. An NFC reader IC is a specialized radio-frequency integrated circuit that manages the modulation, demodulation, and protocol handling required for near-field communication. It sits at the heart of contactless systems, bridging the digital host interface (typically SPI or I2C) and the analog RF front-end that drives the antenna. In the system hierarchy, the ST25R3920B functions as the physical layer and data-link layer controller, working alongside a host microcontroller (MCU) that runs the application stack. This separation allows designers to implement complex NFC functionality without deep RF expertise. Key features of the ST25R3920B include support for both active and passive peer-to-peer modes, an automatic antenna tuning system, and a low-power field detection mode that enables battery-efficient wake-up. The device also offers a high receiver sensitivity of -70 dBm, ensuring reliable reading of low-signal tags. Its integrated voltage regulator simplifies power supply design, and the SPI interface supports clock speeds up to 10 MHz for fast data transfer. From a technical architecture perspective, the ST25R3920B integrates a highly linear RF front-end with a 13.56 MHz carrier generation circuit, a multi-protocol framing engine, and a flexible FIFO buffer. The device uses a digital demodulator with adaptive filtering to handle various modulation depths and data rates, from 106 kbps to 848 kbps. Its automatic antenna tuning algorithm continuously adjusts the matching network to compensate for environmental detuning, maintaining optimal performance across different antenna designs and operating conditions. Typical applications include point-of-sale terminals, access control systems, NFC-enabled smart locks, and industrial asset tracking. In a POS terminal, the ST25R3920B provides the RF interface for contactless payment cards and mobile wallets, supporting the required EMVCo and NFC Forum compliance. For access control, its low-power field detection allows battery-operated door locks to wake up only when a card is presented, extending battery life. When designing with the ST25R3920B, careful attention must be paid to antenna matching and PCB layout to achieve optimal read range. The device's automatic tuning feature helps, but the antenna coil's inductance and Q-factor must be within the specified range. Additionally, proper decoupling and grounding are essential to minimize noise and ensure stable operation.
STM32WB15CCU6 - 2.4GHz BLE 5.2 Wireless MCU, 320KB Flash | STMicroelectronics
The STMicroelectronics STM32WB15CCU6 is a dual-core wireless microcontroller integrating a 64 MHz Arm Cortex-M4 application processor and a 32 MHz Arm Cortex-M0+ radio processor, designed for Bluetooth Low Energy 5.2 applications. It features 320 KB of flash memory and 48 KB of SRAM, housed in a 48-pin UFQFPN (UFQFPN-48) package with dimensions of 7x7 mm. The device supports a supply voltage range of 1.71V to 3.6V and operates over a temperature range of -40°C to +105°C, making it suitable for industrial and consumer IoT applications. A wireless microcontroller (MCU) is a system-on-chip that integrates a general-purpose microcontroller core with a radio transceiver, enabling wireless communication protocols such as Bluetooth Low Energy, Zigbee, or proprietary sub-GHz protocols. In the system hierarchy, a wireless MCU sits above a standalone MCU and below a full application processor, providing a balance of processing capability, low power consumption, and wireless connectivity. The STM32WB15CCU6 specifically targets Bluetooth Low Energy 5.2, offering a complete solution for connected devices without requiring an external radio chip. Key features of the STM32WB15CCU6 include a 2.4 GHz radio supporting Bluetooth Low Energy 5.2 with a transmit power of up to +6 dBm and a receiver sensitivity of -96 dBm, ensuring robust wireless links. The dual-core architecture allows the Cortex-M0+ to handle the radio stack independently, freeing the Cortex-M4 for application tasks, which improves real-time performance and reduces power consumption. The device also includes a rich set of peripherals, including multiple UART, SPI, I2C interfaces, a 12-bit ADC, and a random number generator, providing flexibility for various sensor and control applications. From a technical depth perspective, the STM32WB15CCU6 leverages ST's advanced 40nm process technology, enabling low power consumption with multiple low-power modes, including a standby mode with a current consumption of only 1.6 µA. The radio architecture includes a dedicated hardware encryption engine supporting AES-128, AES-256, and other algorithms, ensuring secure wireless communication. The device also features a true random number generator (TRNG) and a unique 96-bit ID, enhancing security for IoT applications. Typical applications include smart home devices such as smart locks, sensors, and lighting controls, as well as healthcare wearables, industrial wireless sensor networks, and asset tracking systems. The STM32WB15CCU6's low power consumption and robust wireless performance make it ideal for battery-powered devices that require long operational lifetimes. When designing with this device, ensure proper antenna matching and PCB layout for the 2.4 GHz radio to achieve optimal range and reliability. The device requires a 32.768 kHz crystal for the low-power RTC and a 32 MHz crystal for the radio, and careful attention to power supply decoupling is essential to minimize noise and ensure stable operation.
STM32WB55RGV6 - Dual-Core BLE 5.3 MCU 1MB Flash | STMicroelectronics
The STMicroelectronics STM32WB55RGV6 is an ultra-low-power multiprotocol wireless microcontroller with a dual-core architecture - an Arm Cortex-M4 with FPU running at 64 MHz for the application and an Arm Cortex-M0+ running at 32 MHz dedicated to the radio stack - with 1 Mbyte of Flash memory, integrated Bluetooth Low Energy 5.3/5.4-compliant and IEEE 802.15.4-2011 radio covering 2.405 GHz to 2.48 GHz, housed in a 68-pin VFQFPN exposed-pad package. A wireless MCU is a microcontroller that integrates both a processing core and a radio transceiver on a single die, sitting at the intersection of the microcontroller and RF transceiver product categories within the broader wireless-connectivity semiconductor hierarchy. By partitioning the real-time radio stack onto the Cortex-M0+ and the user application onto the Cortex-M4, the STM32WB55 family guarantees RF protocol timing independence from application load - a key architectural advantage over single-core BLE MCUs. Key features include 1 MB of Flash and 256 KB of SRAM for application and stack storage, support for Bluetooth 5.3, Thread, and Zigbee protocols on the same silicon, a rich peripheral set (USB 2.0 full-speed device, USART, SPI, I2C, I2S, Quad-SPI, 12-bit ADC, comparators, touch sensing), and ultra-low-power modes with down to a few microamps in Stop 2 with RAM retention. The integrated balun and output power up to +6 dBm (as per family datasheet range) simplify RF front-end design. The dual-core radio architecture offloads BLE/802.15.4 stacks from the application core, so deterministic real-time behavior, security via the Cortex-M0+ trust boundary, and OTA firmware update capability are maintained even under heavy application processing. The 68-pin VFQFPN-EP (7x7 mm class) package provides a good GPIO count for sensor hubs and HMI. Typical applications include smart-home sensors and lighting (Thread/Zigbee), Bluetooth LE beacons and wearables, industrial wireless nodes, and medical monitoring devices. Design consideration: RF layout requires a 50-ohm match to the antenna and solid ground planes on the exposed pad; verify the exact radio output-power and sensitivity figures against the official STM32WB55xx datasheet. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and design notes not found in the manufacturer datasheet.
STM32WB55VEQ6 - 2.4GHz Dual-Core Wireless MCU | STMicroelectronics
The STMicroelectronics STM32WB55VEQ6 is a dual-core wireless microcontroller that integrates a 64 MHz Arm Cortex-M4 application processor with a 32 MHz Arm Cortex-M0+ dedicated to radio processing, enabling concurrent execution of application code and Bluetooth Low Energy (BLE) 5.0, Zigbee 3.0, and OpenThread stacks. It is housed in a 129-ball UFBGA (VQFN-129) package, offering a compact footprint for space-constrained IoT devices. A wireless microcontroller (MCU) is a system-on-chip that combines a general-purpose processor core with a radio transceiver, allowing embedded systems to communicate wirelessly. The STM32WB55VEQ6 belongs to the STM32WB series, which is part of the broader STM32 family of 32-bit Arm Cortex-M microcontrollers. This hierarchy places it within the categories of wireless MCU -> microcontroller -> embedded processor -> semiconductor, providing a clear taxonomy for engineers selecting components for IoT applications. Key features include 1 Mbyte of flash memory and 256 Kbytes of SRAM, providing ample storage for complex application firmware and protocol stacks. The device supports a wide supply voltage range of 1.71V to 3.6V, making it suitable for battery-powered applications. It also integrates a rich set of analog peripherals, including a 12-bit ADC, operational amplifiers, and comparators, as well as digital interfaces such as SPI, I2C, USART, and USB 2.0 FS. The radio supports BLE 5.0 with a data rate of up to 2 Mbps, Zigbee 3.0, and OpenThread, with a typical sensitivity of -96 dBm for BLE. The dual-core architecture allows the Cortex-M0+ to handle all real-time radio protocol processing, while the Cortex-M4 runs the application code, ensuring deterministic wireless performance without burdening the main processor. The device also features a hardware cryptographic accelerator (AES, RSA, ECC) and a true random number generator (TRNG) for secure communication, which is critical for IoT security. Typical applications include smart home devices (e.g., smart locks, sensors, lighting), industrial wireless sensor networks, healthcare wearables, and asset tracking systems. The low-power modes, including Sleep, Stop, and Standby, with current consumption as low as 1.62 uA in Standby mode, extend battery life in portable applications. When designing with this device, ensure proper antenna matching and RF layout to achieve optimal radio performance. The device requires a 32.768 kHz crystal for the RTC and a 32 MHz crystal for the radio, and careful PCB design is essential to minimize interference between the RF section and digital circuitry.
STM32WBA52CEU6 - Arm Cortex-M33 BLE 5.4 MCU | STMicroelectronics
The STM32WBA52CEU6 is a 32-bit Arm Cortex-M33 microcontroller from STMicroelectronics, featuring a 100 MHz core with TrustZone, DSP instructions, and a floating-point unit (FPU). It integrates a 2.4 GHz radio supporting Bluetooth Low Energy (BLE) 5.4, making it ideal for secure IoT and wireless applications. The device comes in a UFQFPN-48 package (7x7 mm) and operates over a supply voltage range of 1.71V to 3.6V. A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It contains a processor core, memory, and programmable input/output peripherals. The STM32WBA52CEU6 belongs to the STM32WBA series, which is part of the broader STM32 family of 32-bit microcontrollers. This series is optimized for wireless connectivity, combining the Arm Cortex-M33 core with a radio transceiver, enabling secure and low-power communication in IoT devices. Key features include 512 KB of flash memory and 128 KB of SRAM, a rich set of analog and digital peripherals, and advanced security features such as TrustZone, secure boot, and hardware cryptographic accelerators. The BLE 5.4 radio supports long-range, high-throughput, and advertising extensions, with a link budget of up to 105 dB. The device also includes a 12-bit ADC, multiple timers, and communication interfaces like SPI, I2C, USART, and USB. The STM32WBA52CEU6 is built on a low-power process technology, offering multiple low-power modes including Sleep, Stop, and Standby, with typical current consumption as low as 2.2 uA in Standby mode with RTC. The TrustZone technology provides hardware-enforced isolation for secure code execution, making it suitable for applications requiring robust security, such as secure payment, authentication, and firmware protection. Typical applications include smart home devices, industrial sensors, medical wearables, and asset tracking. The integrated BLE radio and security features make it a strong choice for IoT edge nodes that need secure wireless communication. The device supports over-the-air (OTA) firmware updates, enabling remote maintenance and feature updates. When designing with this MCU, ensure proper antenna matching for the BLE radio and follow the layout guidelines in the datasheet to minimize RF interference. The supply voltage should be decoupled with a 100 nF capacitor close to each VDD pin, and the VDDA pin should have a dedicated 1 uF capacitor for analog performance.