RF & Wireless
ژێرپۆلەکان
بەرهەمەکان (730+)
CC115LRGPR - Sub-1GHz RF Transmitter 12dBm | Texas Instruments
The Texas Instruments CC115LRGPR is a value line sub-1 GHz RF transmitter supporting FSK, GFSK, and OOK modulation with up to 12 dBm output power and data rates up to 600 kbps, covering the 300-348 MHz, 387-464 MHz, and 779-928 MHz ISM/SRD frequency bands in a 20-pin VQFN (RGP) exposed-pad package rated from -40C to +85C. A sub-1 GHz RF transmitter is a single-chip wireless device that converts baseband data into a modulated RF carrier for license-free industrial, scientific, and medical (ISM) or short-range device (SRD) bands. Within the wireless connectivity hierarchy, it sits below full transceivers (which add a receive path) and above complete modules, forming the transmit half of a low-cost RF link. Texas Instruments designed the CC115L value line transmitter to pair with the CC113L value line receiver, enabling a bidirectional-capable but cost-optimized radio system. Key features include RF performance identical to the popular CC1101 RF transceiver, 12 dBm maximum output power for range-critical links, flexible FSK/GFSK/OOK modulation, and data rates up to 600 kbps. A fast wake-to-transmit latency of approximately 240 microseconds supports aggressive duty-cycling for battery-powered nodes. The device requires minimal external components: only a crystal, a few decoupling capacitors, and a simple antenna-matching network. Technically, the CC115L shares its radio architecture and register map with the CC1101, which means SmartRF Studio configuration files and RF register settings developed for CC1101 transmit chains port directly to the CC115L. The standard SPI interface (SCLK, SI, SO, CSn) connects to virtually any low-cost microcontroller, and packet-oriented data FIFOs offload the host MCU from bit-level timing. TX-only operation reduces die area and cost compared with the CC1101 transceiver. Typical applications include 433 MHz and 868/915 MHz remote controls and keyless entry, wireless alarm and security sensors, sub-1 GHz IoT sensor nodes for smart metering, and industrial telemetry where the 12 dBm output extends link range through building structures. According to Texas Instruments, the CC115L is EN 300 220 and FCC Part 15-friendly for SRD system designs. Design consideration: RF matching networks are band-specific; use TI reference designs (e.g., the 433 MHz and 868/915 MHz matching networks in the CC115L datasheet) and place the exposed ground pad on a solid ground plane with multiple vias for RF ground integrity and thermal dissipation. This page synthesizes distributor pricing, drop-in alternative analysis, pinout data, and practical RF layout guidance not found together in the manufacturer datasheet, with pricing verified as of 2026-10-19.
CC115LRGPT - Sub-1GHz RF Transmitter 12dBm | TI
The Texas Instruments CC115LRGPT is a value line sub-1 GHz RF transmitter delivering up to 12 dBm output power at 600 kbps data rate, housed in a 20-pin VQFN (RGP) 4x4 mm package with exposed pad. It supports FSK, GFSK, and OOK modulation in the 315 MHz, 433 MHz, 868 MHz, and 915 MHz ISM/SRD frequency bands. A sub-1 GHz RF transmitter is a wireless integrated circuit that generates modulated RF carriers for low-data-rate, long-range links. Within the radio hierarchy, it sits below full transceivers (no receive path) and above pure RF front ends, forming part of a broader power-management and connectivity ecosystem alongside microcontrollers and antenna matching networks. Sub-1 GHz links favor range and penetration over bandwidth, making them the backbone of sensor networks and remote-control systems. Key features include a cost-optimized architecture derived from the popular CC1101 RF transceiver with identical RF performance characteristics, support for both asynchronous and synchronous serial transmit modes for backwards compatibility with existing radio protocols, and a compact QLP 4x4 mm 20-pin footprint that suits space-constrained designs. Technically, the CC115L integrates a complete transmit chain: a fractional-N synthesizer, programmable frequency synthesizer control via an SPI-compatible interface, and a power amplifier with programmable output power up to 12 dBm. The device is suited for systems targeting compliance with EN 300 220 (Europe) and FCC CFR Part 15 (US) per the TI product page. Typical applications include low-cost wireless sensor nodes, remote keyless entry transmitters, and one-way telemetry links, where pairing the CC115L transmitter with a CC113L value line receiver enables a complete low-cost bidirectional RF link. When designing with the CC115LRGPT, follow the TI reference designs for RF matching network components and reference oscillator layout; supply voltage is 2.5V to 3.3V per distributor data, and the exposed pad must be soldered to a solid ground plane for RF performance. This page synthesizes distributor availability, drop-in alternatives, and practical design guidance beyond what the manufacturer datasheet provides.
CC1310F128RHBR - Sub-1GHz Wireless MCU | Texas Instruments
The Texas Instruments CC1310F128RHBR is a SimpleLink ultra-low-power Sub-1 GHz wireless microcontroller integrating a 32-bit ARM Cortex-M3 core, 128 kB flash, 20 kB SRAM, and a dedicated Sub-1 GHz RF transceiver in a 32-pin VQFN (RHB) 5x5 mm package with exposed pad. It supports ISM/SRD frequency bands from 300 MHz to 930 MHz with transmit power up to +14 dBm and receiver sensitivity as low as -124 dBm in long-range mode. What is a Sub-1 GHz wireless MCU? A wireless MCU combines an application processor, memory, peripherals, and a radio transceiver in a single die to enable compact, low-power connected nodes. The CC1310 belongs to the SimpleLink microcontroller platform (a TI ecosystem covering Wi-Fi, Bluetooth Low Energy, Sub-1 GHz, Thread, Zigbee, and host MCUs) and fits the hierarchy: wireless MCU -> microcontroller -> SoC -> semiconductor. Its dedicated ARM Cortex-M3 runs application code, while an autonomous Sensor Controller offloads polling and analog sampling tasks without waking the main CPU, dramatically cutting average current. Key features include industry-leading low-power consumption (0.7 µA standby with RTC retention, 5.5 mA RX, 12.9 mA TX at +10 dBm), integrated balun and DC/DC converter, AES-128 hardware cryptography, and a wide 1.8 V to 3.8 V supply range. The radio supports 2-(G)FSK, 4-(G)FSK, MSK, OOK, and configurable modulation schemes, paired with the TI 15.4-Stack or proprietary sub-GHz protocols. The Cortex-M3 runs up to 48 MHz with 4 KB instruction cache and 2 KB power-on-reset cache, enabling responsive application code. Typical applications include smart metering (gas/water/heat), building automation (HVAC, lighting, security panels), industrial IoT sensor nodes, wireless alarm and security systems, and long-range remote controls. The combination of -124 dBm sensitivity and +14 dBm output permits line-of-sight links beyond several kilometers in suitable regulatory bands. When designing with this device, follow TI reference layouts for the 5x5 mm RHB package to preserve RF performance. Use a 32.768 kHz crystal for RTC and an optional 24 MHz TCXO reference for narrow-band operation. Match the antenna impedance to 50 Ω via the integrated balun output. TI's SimpleLink CC13x0 SDK and Code Composer Studio provide pre-certified 15.4-Stack and EasyLink examples for fast prototyping.
CC1312PSIPMOTR - Sub-1GHz SiP RF Module | Texas Instruments
The Texas Instruments CC1312PSIPMOTR is a Sub-1 GHz system-in-package (SiP) wireless microcontroller module with an integrated power amplifier, operating across the 861 MHz to 930 MHz ISM bands (863 MHz to 930 MHz per ordering information; the radio supports 861 MHz to 1030 MHz), rated from -40C to +105C and housed in a 48-pin QFM (MOT) land-grid package supplied in tape and reel. A system-in-package wireless MCU combines a radio transceiver, a microcontroller, crystal oscillators, RF matching components and decoupling capacitors inside a single pre-tested package. In the power-management hierarchy of an IoT node, a SiP sits above a bare transceiver IC: it removes the hardest part of RF design, the antenna matching network and layout sensitivity, and replaces it with a surface-mount component that can be reflowed onto a standard PCB. The CC1312PSIP integrates a CC1312R device die plus an integrated power amplifier for increased link budget. Key features include support for IEEE 802.15.4-based stacks (Wi-SUN, Thread-compatible PHYs) and proprietary Sub-1 GHz protocols, operation on the SimpleLink MCU platform, and a Common SimpleLink Low Power F2 SDK shared across the family. The integrated PA extends output power and therefore range compared with non-PA SiP versions, which matters for metering and streetlight meshes. Technically, the device belongs to the SimpleLink F2 family and is supported by the SysConfig system configuration tool. TI explicitly states that the CC1312PSIP portfolio includes pin-compatible 2.4 GHz SiPs, so a product can migrate between communication standards (Sub-1 GHz and 2.4 GHz) on the same PCB footprint, protecting firmware and hardware investment. Typical applications include Wi-SUN mesh networks for smart utilities, wireless sensor networks in the 868/915 MHz bands, and long-range IoT nodes where the PA-enhanced link budget enables multi-kilometer range in rural deployments. Design consideration: as a SiP module, the CC1312PSIP still requires a clean 48-pin land pattern, ground vias under the package, and an antenna feed designed for the target band; follow the TI reference design impedance exactly. This page synthesizes verified distributor data, drop-in alternatives and practical design notes not found on the manufacturer datasheet alone.
CC2652R1FRGZR - Multiprotocol 2.4GHz Wireless MCU | TI
The Texas Instruments CC2652R1FRGZR is a SimpleLink multiprotocol 2.4 GHz wireless MCU with 352 kB flash, 88 kB RAM, and a 32-bit Arm Cortex-M4F application core, housed in a 48-pin VQFN (RGZ) package with exposed thermal pad. A wireless MCU (wireless microcontroller unit) is a system-on-chip that combines a microcontroller core with a radio transceiver, enabling both wireless communication and embedded application processing in a single device. Wireless MCUs sit within the broader hierarchy of embedded processors -> microcontrollers -> wireless MCUs -> RF transceiver SoCs, and are the foundation of modern IoT and smart-home node design. Key features of the CC2652R1FRGZR include support for Bluetooth 5.2 Low Energy, Zigbee 3.0, Thread, IEEE 802.15.4, 6LoWPAN, and TI 15.4-Stack proprietary protocols. The Dynamic Multiprotocol Manager (DMM) enables concurrent multiprotocol operation on a single radio, letting one hardware design serve multiple ecosystems. Programmable RF output reaches up to +5 dBm across the 2.4 GHz to 2.48 GHz band. Technically, the device uses a dual-core architecture: the Cortex-M4F runs application code while an autonomous Cortex-M0 radio controller handles real-time protocol timing, and a dedicated sensor controller operates in standby for always-on sensing with minimal current. The radio core draws approximately 5.9 mA in RX and 5.4 mA in TX at 0 dBm, enabling multi-year coin-cell battery life. Hardware crypto acceleration covers AES-128/256, SHA2, ECC, and RSA. Typical applications include smart-home devices such as locks, lighting, and sensors; industrial wireless sensor networks; and asset tracking tags where multiprotocol flexibility reduces inventory complexity. Design consideration: decouple power pins with 0.1 uF and 1 uF capacitors close to the device, use TI reference-design balun and matching networks, and solder the exposed pad to a solid ground plane. This page synthesizes distributor pricing, verified drop-in alternatives, comparison data, and practical design notes not consolidated in the manufacturer datasheet.
CC3135RNMARG - Dual-Band Wi-Fi Network Processor | Texas Instruments
The Texas Instruments CC3135RNMARG is a dual-band Wi-Fi network processor designed to connect any microcontroller (MCU) to the Internet of Things (IoT). It integrates an Arm Cortex-M3 MCU dedicated to Wi-Fi and internet protocols, offloading networking tasks from the host MCU. The device supports 802.11a/b/g/n in the 2.4 GHz and 5 GHz bands, with a 64-pin VQFN package (RGK suffix). It operates from a 2.3V to 3.6V supply and includes a 1-A low-dropout voltage regulator with enable, simplifying power design. A Wi-Fi network processor is a specialized IC that handles all Wi-Fi communication and networking protocols, allowing a host MCU to focus on application tasks. It sits between the host MCU and the RF front-end, managing the radio, baseband, and protocol stack. This offloads complex networking code, reduces host processing load, and accelerates time-to-market for IoT products. Key features include dual-band operation (2.4 GHz and 5 GHz), integrated Arm Cortex-M3, hardware security with crypto accelerators, and support for WPA2/WPA3 personal and enterprise security. The device also offers a rich set of internet protocols such as TCP/IP, TLS, and HTTP, enabling secure cloud connectivity. Its low-power modes (LPDS, hibernate) are optimized for battery-powered IoT devices. Technically, the CC3135 integrates a complete RF front-end, including PA, LNA, and RF switch, reducing external component count. It uses a 64-pin VQFN package (RGK) with exposed thermal pad for efficient heat dissipation. The device is part of TI's SimpleLink family, offering a unified software development kit (SDK) and compatibility with various host MCUs via SPI or UART interfaces. Typical applications include smart home devices, industrial automation, wireless sensors, and portable electronics. Its dual-band capability ensures robust connectivity in congested environments, while the integrated security features protect data in transit. The device is ideal for applications requiring reliable, secure Wi-Fi connectivity with minimal host MCU overhead. When designing with the CC3135, ensure proper RF layout and antenna matching for optimal performance. The integrated LDO simplifies power supply design, but external decoupling capacitors are required. Also, consider the host interface (SPI or UART) and use the TI SDK for rapid development.
CC3230SF12RGKR - Wi-Fi Wireless MCU | Texas Instruments
Texas Instruments CC3230SF12RGKR is a SimpleLink Wi-Fi wireless MCU integrating an Arm Cortex-M4 processor, 2.4 GHz 802.11b/g/n radio, 256 kB RAM, and 1 MB of XIP flash in a 64-pin VQFN (RGK) package with an exposed pad. It operates across the 2.412 GHz to 2.472 GHz frequency range and is designed for embedded Wi-Fi systems requiring integrated processing, connectivity, security, and application storage. A wireless MCU combines a microcontroller and radio transceiver in one device, allowing an embedded product to perform local control and processing while exchanging data over a wireless network. The CC3230SF belongs to the wireless MCU category, combining an Arm Cortex-M4 MCU, Wi-Fi radio, memory, networking firmware, and security capabilities within a single surface-mount package. Key features include 256 kB RAM, 1 MB XIP flash, Wi-Fi coexistence, WPA3 support, 16 TLS sockets, secure boot, device identity and keys, file-system encryption, and user-image encryption. The device also supports 802.11b/g/n operation over 2.412 GHz to 2.472 GHz, making it suitable for connected sensors, gateways, industrial equipment, and consumer IoT products. The CC3230SF12RGKR is supplied in the RGK package identified by the part number suffix. The manufacturer product page specifies a 64-pin VQFN package with an exposed pad and an operating temperature range of -40°C to 85°C. The integrated memory arrangement is useful for firmware, networking configuration, and application data without requiring a separate external memory device. Typical applications include Wi-Fi sensors, smart-home nodes, industrial monitoring systems, connected appliances, access-control equipment, portable devices, and low-cost Internet of Things gateways. The integrated radio and MCU simplify board design by reducing component count, while coexistence support helps manage wireless-network coexistence requirements. Design considerations include careful RF layout, controlled impedance routing, adequate decoupling, exposed-pad thermal management, and verification of the complete firmware and security configuration. Use the manufacturer datasheet and product documentation for pin assignments, RF layout guidance, power sequencing, antenna design, and programming requirements. This page combines the verified product identity, package information, connectivity features, security capabilities, pricing context, application guidance, and replacement considerations for engineers evaluating the CC3230SF12RGKR.
CC430F5145 - Sub-1GHz RF SoC MCU 16kB Flash | Texas Instruments
The Texas Instruments CC430F5145 is a 16-bit ultra-low-power sub-1 GHz wireless microcontroller system-on-chip (SoC) integrating the MSP430 CPUXV2 core with a CC1101 RF transceiver, offering 16kB of in-system programmable flash, 2kB of RAM, a 10-bit ADC, and a 48-pin VQFN (RGZ) package with exposed pad. A wireless MCU SoC combines a microcontroller and a radio transceiver on a single die, eliminating the inter-chip interface that a discrete MCU-plus-transceiver design requires. Within the power management and RF signal chain hierarchy, the CC430 family occupies the single-chip wireless node tier, sitting above discrete transceivers (such as the standalone CC1101) and below multi-chip RF modules. Single-die integration reduces BOM count, board area, and inter-chip digital interface noise. Key features of the CC430F5145 include sub-1 GHz operation across three license-free ISM bands (300-348 MHz, 389-464 MHz, and 779-928 MHz), the ultra-low-power MSP430 CPUXV2 architecture with multiple low-power modes, a high-performance 10-bit ADC with six external inputs plus internal temperature and battery sensors, and two 16-bit timers. The CC1101-based RF core provides configurable modulation, data rate, and channel spacing for flexible ISM-band link design. Technically, the device merges TI's proven CC1101 transceiver front end with the MSP430 bus architecture, so RF register configuration, packet handling, and application code all execute on one CPU. This removes the SPI timing race conditions and firmware coordination overhead typical of two-chip designs. Flash memory is in-system programmable, supporting field firmware and RF-parameter updates. Typical applications include sub-1 GHz wireless sensor networks, AMR/utility metering, home and building automation, alarm and security systems, and industrial monitoring nodes where long range, low duty cycle, and multi-year battery life dominate the design. Design-wise, RF layout on the RGZ-48 exposed-pad package demands a solid ground plane, short matching-network traces, and careful antenna placement; the exposed pad must be soldered to ground for both thermal and RF performance. This page synthesizes datasheet parameters, drop-in family alternatives, pricing, and practical design notes not consolidated in the manufacturer datasheet.
CC430F5145IRGZT - Sub-1GHz RF SoC, 16kB Flash | Texas Instruments
The Texas Instruments CC430F5145IRGZT is a 16-bit ultra-low-power wireless microcontroller system-on-chip (SoC) combining an MSP430 CPUXV2 core with an integrated CC1101 sub-1 GHz RF transceiver in a 48-pin VQFN (RGZ) package with exposed pad. It offers 16kB in-system programmable flash, 2kB RAM, a 10-bit ADC, and operates across the 300-348 MHz, 389-464 MHz, and 779-928 MHz ISM/SRD bands. A wireless MCU, or RF SoC, integrates a general-purpose microcontroller and a radio transceiver on a single die, collapsing the traditional two-chip MCU-plus-transceiver architecture into one package. This reduces bill-of-materials count, board area, and inter-chip interface complexity, sitting within the broader hierarchy of microcontrollers and RF transceiver ICs in the power management and connectivity domain. Key features include the CC1101-format radio supporting flexible modulation (2-FSK, GFSK, MSK, OOK, ASK), programmable data rates, and packet handling in hardware; ultra-low-power operation typical of the MSP430 family with multiple low-power modes; two 16-bit timers; and a high-performance 10-bit ADC with six external inputs plus internal temperature and battery sensors. Technically, the RF core shares a single crystal with the digital domain, and the MSP430 CPUXV2 delivers efficient 16-bit computation with fast wake-up from low-power modes, making the device well suited to battery-powered duty-cycled networks. The unified architecture simplifies RF-to-MCU data flow through dedicated radio register interfaces. Typical applications include wireless sensor networks, smart metering, building automation, alarm and security systems, and industrial telemetry, where multi-year battery life and robust sub-1 GHz link budgets matter more than raw throughput. Design consideration: RF layout of the VQFN-48 exposed pad requires careful impedance matching to the antenna per TI reference designs (e.g., DN023 style matching networks), and developers should budget flash/RAM headroom since 16kB/2kB is the smaller end of the CC430 memory range.
CC660D-LS - 3GPP NTN Satellite IoT Module LCC+LGA | Quectel
The Quectel CC660D-LS is a 3GPP NTN (Non-Terrestrial Network) satellite communication module that supports 3GPP Release-17 IoT-NTN connectivity in L-band (B255) and S-band (B256/B23), housed in a compact LCC + LGA surface-mount package measuring 17.7 mm × 15.8 mm × 2.0 mm. It delivers two-way data communication plus SMS SOS functionality, enabling direct device-to-satellite links for IoT deployments that previously required terrestrial cellular coverage. A satellite IoT module is a self-contained wireless subsystem that integrates a baseband transceiver, RF front-end, power management and host interface into a single certified PCB. Within the broader electronics taxonomy it sits as: IoT module -> wireless module -> RF module -> electronic component. Direct-to-satellite modules like the CC660D-LS remove the dependency on terrestrial base stations, extending connectivity to maritime, agricultural, asset-tracking and emergency-response use cases where cellular coverage is absent. Key features include IoT-NTN Rel-17 protocol support over L-band (B255) and S-band (B256/B23), GNSS location reporting, integrated IP/UDP/TCP stacks, and an ultra-compact 17.7 × 15.8 × 2.0 mm LCC + LGA footprint suitable for SMT mass production. The module is designed for durable, rugged designs and is positioned for size-sensitive end products. Technically, the CC660D-LS pairs a 3GPP Rel-17 IoT-NTN baseband with multi-band RF front-end and integrated GNSS for location reporting. Because it operates exclusively through non-terrestrial network satellites, link budget, antenna gain and sky-view geometry become dominant design considerations; the module is intended to be paired with an active or passive NTN-tuned antenna. Typical applications include global asset tracking, maritime and fishery monitoring, agricultural sensor telemetry, SCADA fallback for remote industrial sites, and emergency SOS wearables. It is generally used together with a GNSS module, since CC660D-LS relies on GNSS to update location before transmitting via satellite. When designing with this module, ensure the host platform supplies a stable 3.3 V–4.3 V supply, that the antenna is tuned for the chosen NTN band, and that the SIM interface matches the operator's satellite SIM provisioning (which differs from terrestrial SIMs). This page synthesizes distributor availability, parametric positioning versus competing IoT-NTN modules, and practical integration notes not found in the manufacturer datasheet alone.
CI522 - 13.56MHz ISO14443A RFID Reader IC QFN-16 | Nanjing Zhongke
The Nanjing Zhongke Microelectronics CI522 is a 13.56 MHz contactless reader/writer IC supporting ISO/IEC 14443 A communication at up to 848 Kbit/s, housed in a 16-pin QFN-EP (3x3 mm) package. It integrates a built-in antenna driver, hardware data verification (CRC/parity), low-power wake-up, and an SPI host interface operating from 2.3 V to 4 V supply, targeting contactless reader front-ends in access control, smart-locker, and NFC token applications. What is an RFID reader IC? An RFID reader IC (radio-frequency identification reader IC) is a contactless front-end transceiver that powers a passive transponder (tag or card) over a magnetic field at 13.56 MHz, exchanges modulated data using a defined air protocol such as ISO/IEC 14443 A/B or ISO 15693, and presents a digital interface (SPI, UART, I2C) to a host microcontroller. It belongs to the broader hierarchy: RFID reader IC -> 13.56 MHz NFC front-end -> contactless communication IC -> wireless/RF semiconductor -> semiconductor device. The CI522 implements the type-A sub-protocol of ISO/IEC 14443, which is the most widely deployed air interface for contactless smartcards (MIFARE Classic, MIFARE Ultralight, NTAG) and is the de-facto standard for transit fare cards and access badges. Key features include an integrated transmit-side antenna driver capable of driving a printed or wound loop directly without an external power amplifier, on-chip CRC and parity verification to offload the host MCU, a configurable low-power wake-up mode that periodically polls the RF field to extend battery life in coin-cell designs, and SPI communication up to 10 Mbit/s. The 3x3 mm QFN-EP package with exposed pad keeps the PCB footprint compact while the thermal pad provides a low-impedance ground reference that is essential for stable RF performance. Technically, the CI522 combines a 13.56 MHz resonant bridge with modulation/demodulation, anti-collision logic compliant with ISO 14443-3 type A, and a small command engine that handles REQA, SELECT, AUTH, READ, WRITE, and HALT transactions internally. Its low-power wake-up and short command latency enable wake-on-proximity designs where the host sleeps until a card is detected. Typical applications include access control readers, RFID card writers/programmers for MIFARE Classic 1K/4K and Ultralight tags, smart-locker and shared-mobility kiosks, NFC payment terminals (Type A tags), and battery-powered handheld readers. In each case the CI522 handles the RF and protocol layers so that the host MCU can focus on application logic. A key design consideration is the antenna matching network - the loop inductance, tuning capacitor, and EMC filter values must be chosen for the specific coil geometry and target card distance; using the recommended reference design from the manufacturer datasheet is the safest path. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
CLRC66303HN - 13.56MHz Multi-Protocol NFC Frontend | NXP
The NXP Semiconductors CLRC66303HN is a high-performance multi-protocol NFC frontend (contactless reader IC) operating at 13.56 MHz, supporting ISO/IEC 14443A/MIFARE, ISO/IEC 14443B, ISO/IEC 15693, ISO/IEC 18000-3 mode 3 and FeliCa, with a 2.5V to 5.5V supply range in a 32-pin HVQFN (VFQFN) exposed-pad package. An NFC frontend is the analog radio layer of a contactless system: it sits between a host microcontroller and the antenna coil, generating the 13.56 MHz carrier, modulating and demodulating signals, and handling framing at the physical layer. In the system hierarchy it belongs to the family of RFID reader ICs, contactless transceiver ICs, and wireless connectivity semiconductors. The host MCU only needs to interpret protocol frames over SPI, I2C, or serial UART, dramatically reducing firmware complexity. Key features of the CLRC663 plus family include highly flexible multi-protocol support in a single device, a highly efficient integrated analog front end, programmable transmitter output power, and low-power operating modes suited to battery-powered access control terminals. DigiKey classifies the part as an RFID Reader/Transponder IC supporting ISO 14443 with I2C, SPI and UART host interfaces at 2.5V to 5.5V in a 32-VFQFN exposed-pad package. Technically, the device integrates the complete analog front end: low-jitter quartz-stabilized 13.56 MHz carrier generation, programmable TX driver stages, low-noise RX path with programmable gain, automatic antenna tuning assistance, and extensive digital register-level configurability through the host interface. The 32-VFQFN exposed pad provides good RF ground return and thermal performance for compact reader designs. Typical applications include access control readers, gaming and lottery terminals, industrial RFID readers, and NFC-capable point-of-sale or handheld devices, all cited by NXP as target use cases for the CLRC663 plus family. Design consideration: antenna matching is the most critical aspect of a CLRC663 design - follow the NXP antenna design application note and use the 50-ohm or direct-matching network per datasheet guidance; verify EMC compliance on the first layout revision. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in family alternatives, comparison tables, and practical design notes in one place.
CLRC66303HNK - Multi-Protocol NFC Frontend IC | NXP Semiconductors
The NXP Semiconductors CLRC66303HNK is a high-performance multi-protocol NFC frontend (reader IC) belonging to the CLRC663 plus family, delivered in an HVQFN-32 (HNK) package. It functions as a highly flexible 13.56 MHz contactless reader frontend that supports multiple NFC and RFID standards, offering an extended temperature range and pin-to-pin compatibility across the CLRC663 plus family. An NFC frontend, also called an NFC reader IC or contactless reader frontend, is a radio-frequency integrated circuit that generates the 13.56 MHz carrier, modulates and demodulates the contactless signal, and communicates with a host microcontroller that runs the higher protocol layers. In the system hierarchy it sits between the antenna matching network and the host MCU, making it a key element of wireless RF ICs for NFC/RFID reader designs. Key features highlighted by NXP include high performance with flexible antenna design options, remarkably low power consumption with Low Power Card Detection (LPCD) support, and multi-protocol operation covering mainstream contactless standards. The CLRC663 plus family provides extended temperature range operation, which widens its use beyond consumer devices into industrial and infrastructure reader equipment. Technically, the device integrates the analog front end: low-noise receivers, programmable gain, transmit drivers for antenna configurations, and a digital host interface controlled via register access. The host microcontroller executes NXP protocol software such as the NFC Reader Library (NFCRDLib), which the NXP community confirms is the standard software stack for CLRC663-family parts. Typical applications include contactless payment and ticketing terminals, access-control readers, industrial handheld scanners, and embedded NFC modules for smart-home and IoT devices that must read tags such as NTAG Type 2A parts. Design consideration: the HNK (HVQFN-32) variant is the standard packaged option; NXP also offers alternative packaging (such as the HNE option), so verify the exact suffix against your supply plan, and note that Mouser currently lists this part as non-stocked with a 30-week lead time. This page synthesizes distributor pricing, drop-in family alternatives, lead-time data, and practical design guidance not consolidated in the manufacturer datasheet.
CMD199 - 26-35 GHz GaAs Driver Amplifier Die | Qorvo
The Qorvo CMD199 is a wideband 26-35 GHz (K/Ka/Q band) balanced driver amplifier MMIC fabricated in GaAs pHEMT technology, delivering 15 dB of gain with a +19.5 dBm output 1 dB compression point and 3.5 dB noise figure at 30 GHz, supplied as an unpackaged die for hybrid and module assembly. A driver amplifier MMIC is a radio-frequency integrated circuit that provides gain and power boosting between a signal source, such as a synthesizer or upconverter, and a final power amplifier stage. Within the RF signal-chain hierarchy, the driver amplifier sits between low-level gain blocks and the high-power PA, and is a key subcategory of RF/microwave amplifiers within power management of the transmit path. Key features include 50 ohm internally matched input and output, which eliminates the need for external DC blocks and RF port matching networks, full passivation for increased reliability and moisture protection, and a balanced topology that improves output match and linearity across the band. Technically, the balanced amplifier architecture uses two 90-degree hybrid-coupled gain stages, which yields good input/output return loss and graceful degradation. GaAs pHEMT process technology supports the high-frequency gain and high linearity needed at Ka and Q band frequencies, where small size and high dynamic range are critical design requirements. Typical applications include military and defense radar and communications systems, space payloads, satellite communications (SATCOM) uplinks, point-to-point microwave backhaul, and test equipment operating in K, Ka, and Q bands, where the die format enables compact module integration. A key design consideration is die-level assembly: the CMD199 requires chip-and-wire bonding or equivalent hybrid assembly with controlled bond-wire inductance, proper RF grounding via via-holes, and thermal design for the dissipating FETs; supplied DC blocking and bias decoupling must follow the manufacturer datasheet recommendations. This page synthesizes distributor availability, pricing context, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
CMD201P5 - DC-20 GHz GaAs Power Amp +27dBm | Qorvo
The Qorvo CMD201P5 is a wideband GaAs MMIC distributed power amplifier operating from DC to 20 GHz, delivering 11 dB of gain with an output 1 dB compression point of +27 dBm and output IP3 of +37 dBm at 10 GHz, housed in a 32-pin QFN (5x5 mm) surface-mount package. A distributed power amplifier is a class of RF/microwave amplifier in which multiple transistor stages are connected via an artificial transmission-line structure, allowing the gain stages to combine their outputs coherently across extremely wide bandwidths. Within the amplifier hierarchy, the CMD201P5 sits as a power-amplifier-stage MMIC, part of the broader family of RF amplifiers within microwave semiconductors. The distributed topology is what enables its DC-to-20 GHz (L, S, C, X, Ku, and K band) frequency coverage, something reactive-matched narrowband designs cannot achieve. Key features include the very wide DC to 20 GHz bandwidth, 11 dB of flat gain, high linearity with +37 dBm output IP3, and a robust +27 dBm P1dB output power rating. The 50-ohm matched input and output design eliminates the need for external RF port matching networks, dramatically simplifying PCB design and reducing board area. Technically, the GaAs MMIC process provides high transition frequency and consistent performance across the multiband range. The distributed amplifier architecture trades some efficiency for bandwidth, making the part especially attractive where a single amplifier must cover multiple legacy and modern frequency bands. Typical applications include electronic warfare and radar transmitters, wideband test and measurement signal chains, and multi-octave communication links covering L through K band. Design consideration: distributed amplifiers draw DC current continuously, so thermal management of the exposed QFN pad with a solid via-fenced ground connection is essential for reliability. This page synthesizes distributor pricing, verified datasheet parameters, and practical design notes not found in the manufacturer datasheet.
CMD243 - 26-35GHz GaAs Driver Amp, 15.5dB Gain | Qorvo
The Qorvo CMD243 is a wideband GaAs MMIC balanced driver amplifier operating from 26 GHz to 35 GHz (K, Ka and Q bands), delivering 15.5 dB of gain, an output 1 dB compression point of +21 dBm, and a noise figure of 4.4 dB at 30 GHz. The CMD243 is supplied as a bare die and is a 50 ohm matched design, which eliminates the need for external DC blocks and RF port matching. A driver amplifier MMIC is a semiconductor device that boosts signal power in an RF transmit chain, sitting between the upconverter or modulator and the final high-power amplifier. Within the power management hierarchy of an RF front end, the driver stage defines system linearity and noise contribution, and the CMD243 addresses the K/Ka/Q band segment used by satellite communications, point-to-point radio, and radar systems. Key features include balanced amplifier architecture for good input and output return loss across the full 26-35 GHz band, +21 dBm P1dB output power that comfortably drives downstream power amplifiers, and a 4.4 dB noise figure that preserves the link budget of the receiver or transmitter chain. The die format enables integration directly into hybrid microwave assemblies, carrier-bonded modules, and hermetic packages. Technically, the CMD243 is fabricated on Qorvo's GaAs pHEMT MMIC process with full passivation, which provides increased reliability and moisture protection compared with unpassivated die. The balanced topology uses 90-degree hybrids to split and recombine two parallel amplifier stages, improving both match stability and tolerance to bond-wire variation in assembly. Typical applications include military and space communications systems, VSAT and satellite uplinks in Ka band, point-to-point microwave backhaul, and test instrumentation requiring broadband gain in the 26-35 GHz range where small size and high linearity are needed. When designing with the CMD243 die, allow sufficient carrier area for bias routing and RF bond wires, and verify thermal dissipation at the +21 dBm output operating point. Exact bias conditions should be confirmed from the manufacturer datasheet before power-up. This page synthesizes distributor availability, drop-in alternative guidance, and practical die-assembly design notes not found in the manufacturer datasheet.
CMD249K5 - DC-20 GHz GaAs Distributed PA | Qorvo | RF Amplifier
The Qorvo CMD249K5 is a wideband GaAs MMIC (Monolithic Microwave Integrated Circuit) distributed power amplifier, part of Qorvo's CMD249 family, designed for RF and microwave applications from DC to 20 GHz. According to the CMD249 family datasheet, the amplifier delivers greater than 12 dB of gain with a corresponding output 1 dB compression point (P1dB) of +30 dBm and an output third-order intercept point (OIP3) of +38 dBm measured at 10 GHz. The device is fabricated in a 50 ohm matched GaAs pHEMT process, which eliminates the need for external RF port matching and simplifies PCB integration. A distributed power amplifier is a specialized RF amplifier topology that uses the absorption principle of transmission lines to achieve broad bandwidth. Unlike traditional reactively-matched amplifiers whose gain rolls off with frequency, distributed amplifiers maintain flat gain over many octaves by absorbing the parasitic gate and drain capacitances of multiple transistor cells into artificial transmission lines. Distributed amplifiers therefore belong to the broader family of broadband RF amplifiers, themselves a subset of microwave ICs within the RF & Wireless product category. The CMD249 family exploits this topology to deliver usable gain from near-DC up to millimeter-wave frequencies in a single, unconditionally-stable stage. Key features of the CMD249 family include full DC to 20 GHz operational bandwidth, +30 dBm output P1dB, +38 dBm OIP3, 12 dB small-signal gain, 50 ohm input/output match eliminating external matching components, full passivation for enhanced reliability, and 100% DC testing on the wafer. The bare-die form factor requires wirebond or flip-chip interconnect to the host PCB. Compared with reactively-matched power amplifiers that cover only a narrow band, the CMD249K5 trades saturated efficiency for bandwidth - it is the part of choice for instrumentation, EW, and multi-band radar where flat response over many octaves matters more than peak PAE. Typical applications include wideband military EW (electronic warfare) jamming and receiver systems, fiber-optic communication drivers, test and measurement instrumentation, multi-band radar, microwave backhaul, and broadband IF/RF gain blocks. The broadband response also makes the CMD249 family suitable as a generic gain block when the system requires a single amplifier covering multiple downstream frequency plans. Designers should note that GaAs distributed amplifiers dissipate substantial DC power (typically several hundred mA at +5 to +8 V supply) and require careful thermal management even at small duty cycles. The bare die format means ESD handling and clean-room assembly practices are mandatory. Designers should also evaluate the trade-off between the CMD249 family's broadband coverage and the higher efficiency of a narrowband power amplifier if the end application only requires a single band.
CMWX1ZZABZ-091 - LoRaWAN Module 868/915MHz | Murata
The Murata CMWX1ZZABZ-091 is a shielded ultra-small LoRaWAN sub-GHz transceiver module operating in the 868 MHz and 915 MHz ISM bands, integrating an STM32L072 Arm Cortex-M0+ microcontroller with 192 KB flash and an SX1276 LoRa transceiver in a 13.5 x 13.8 mm surface-mount land-grid package. A LoRaWAN module is a complete long-range, low-power wide-area network (LPWAN) radio subsystem that combines an RF transceiver, a host microcontroller, antenna matching, crystal references, and a shielded package into a single certified component. In the system hierarchy it sits above a bare transceiver IC: instead of designing RF matching networks and obtaining regional radio certifications yourself, a module such as the Type ABZ drops into a design with only power, ground, UART/SPI/I2C wiring, and an antenna connection required. Key features include support for LoRaWAN Class A and Class C operation, radio-law certification already obtained for major regions (including CE and FCC for 868/915 MHz deployments), and open MCU design support that exposes all STM32L072 peripherals such as ADC, 16-bit timers, LP-UART, I2C, SPI, and USB 2.0 FS. The module can additionally support Sigfox by modifying the firmware, with Sigfox RC1, RC2, and RC4 certification available through the X-CUBE-SFOX package. The Type ABZ architecture benefits from ST's I-CUBE-LRWAN stack and the B-L072Z-LRWAN1 Discovery kit, which embeds the same module, allowing code developed on the Discovery kit to transfer directly to production hardware. Standby-to-active wake-up occurs in approximately 60 microseconds via NRST, WKUP pins, RTC alarm, or RTC wakeup events, supporting strict battery-life budgets in asset-tracking and metering products. Typical applications include smart utility metering, asset trackers, smart-city sensor nodes, agricultural monitoring, and industrial IoT endpoints that require multi-kilometer range and years of battery life. A key design consideration is supply voltage: the module operates at 1.8 V to 3.6 V, so a primary lithium cell or low-dropout regulator should be chosen with adequate headroom for peak transmit current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
CR95HF-VMD5T - 13.56MHz Multi-Protocol RFID Reader IC | STMicroelectronics
STMicroelectronics CR95HF-VMD5T is a 13.56 MHz RFID reader and NFC transceiver IC with SPI and UART interfaces, a 2.7 V to 5.5 V supply range, and a 32-VFQFN exposed-pad package. It supports ISO/IEC 14443 Type A and B, ISO/IEC 15693, ISO/IEC 18092, and NFC Forum Type 1, 2, 3, and 4 tag operations. An RFID reader IC is the active analog and digital subsystem that generates the 13.56 MHz carrier, conditions reader signals through an antenna interface, detects tag responses, and transfers decoded data to a host processor. The CR95HF belongs to the contactless-communications and NFC/RFID transceiver hierarchy, combining RF analog front-end functions, protocol handling, and serial host connectivity in one surface-mount device. The device provides multi-protocol coverage for ISO/IEC 14443 Type A and B, ISO/IEC 15693 with single or double subcarrier operation, and ISO/IEC 18092 communication. Its NFC capabilities include detection, reading, and writing for NFC Forum Type 1, 2, 3, and 4 tags. These features make it useful for systems that must handle more than one contactless-tag family without relying on separate reader electronics. Communication with a host is available through SPI and UART interfaces, allowing integration with embedded processors and controllers. The listed operating supply range is 2.7 V to 5.5 V, which supports designs using common low-voltage digital rails. The package is a 32-pin VFQFN with an exposed pad, requiring careful land-pattern, thermal-pad, and high-frequency layout implementation. Typical uses include access-control terminals, payment and ticketing readers, asset-tracking equipment, industrial identification systems, consumer NFC readers, and embedded contactless interfaces. The 13.56 MHz operating frequency and protocol support align the part with short-range RFID and NFC applications where a reader must communicate with passive tags or cards. Designers should follow the manufacturer’s antenna, matching, decoupling, and exposed-pad guidance. Because this is a high-frequency RF device, trace geometry, ground continuity, supply filtering, antenna geometry, and exposure to nearby metal or noisy sources can materially affect read range and reliability. Validate the complete reader path with representative tags rather than relying only on digital communication tests. This page combines verified manufacturer and distributor information, interface details, protocol coverage, package information, practical application context, and explicit data gaps for parameters not present in the supplied sources.
CSB-01 - 850/1900 MHz Cellular Signal Booster | Taoglas
The Taoglas CSB-01 is a high-performance, microprocessor-controlled, bi-directional RF amplifier (cellular signal booster) designed for the North American 850 MHz cellular and 1900 MHz PCS frequency bands. It is a finished RF module that integrates a power amplifier, low-noise amplifier, filtering, and digital control into a single enclosed unit with SMA female RF connectors. A cellular signal booster (also called a bi-directional amplifier, BDA, or repeater) is an RF subsystem that captures weak outdoor cellular signals with a donor antenna, amplifies them, and re-radiates the boosted signal indoors through a coverage antenna. The CSB-01 belongs to the RF module family within RF & Wireless subsystems, sitting between the antenna infrastructure and the cellular handset or modem it serves. Key features include dual-band 850/1900 MHz operation covering the North American 2G/3G voice and data spectrum, microprocessor-controlled automatic gain and oscillation detection, integrated band-pass filtering to suppress out-of-band interference, and SMA female RF connectors for easy integration into existing coaxial cable runs. The unit is typically enclosed in a shielded metal housing to provide EMI isolation between the donor and coverage paths. The CSB-01 uses a software-controlled feedback architecture that continuously monitors the uplink and downlink paths for instability, automatically reducing gain or shutting down the affected band if feedback oscillation is detected. This automatic gain control (AGC) and oscillation-shutdown feature enables compliance with FCC Part 20 rules for consumer-signal boosters, which require self-monitoring to prevent the booster from interfering with the carrier network. Typical applications include residential in-building cellular coverage, small office SOHO coverage, basement and below-grade coverage, remote cabin or vacation home signal extension, and vehicle/RV mobile booster systems. The dual-band 850/1900 MHz coverage supports legacy AT&T, Verizon, T-Mobile, and Sprint 2G/3G voice and HSPA/CDMA data services throughout North America. When designing with the CSB-01, plan the antenna isolation between the outdoor donor antenna and the indoor coverage antenna carefully. Insufficient isolation causes feedback oscillation that will trigger the automatic gain reduction; aim for at least 20 dB of physical separation or vertical/horizontal isolation. Power the unit from a clean +12 VDC supply rated for at least 1 A continuous current. This page synthesizes distributor inventory, dual-band specifications, and application guidance not consolidated in the Taoglas datasheet, giving cellular equipment installers and product designers a single reference for evaluating the CSB-01.
CYBLE-012011-00 - BLE v4.1 Module, PSoC 4, 128KB Flash | Infineon
The Infineon CYBLE-012011-00 is a fully certified, turnkey Bluetooth Low Energy (BLE) v4.1 transceiver module based on the Cypress PSoC 4 BLE silicon, integrating a 128 KB flash PSoC, 16 KB SRAM, 23 GPIOs, and a 2.4 GHz trace antenna in a compact surface-mount module. Operating across the 2.4 GHz to 2.48 GHz ISM band, it ships pre-certified to FCC, IC, CE, and Bluetooth SIG specifications, which removes months of RF design and compliance work for cost-sensitive product teams. The module is built around an ARM Cortex-M0 core with a royalty-free BLE stack compatible with Bluetooth 5.1 features (when used with current firmware), and it exposes 23 GPIOs that can be configured for ADC, PWM, UART, SPI, I2C, and CapSense touch interfaces. A Bluetooth Low Energy (BLE) module is a pre-engineered radio subsystem that bundles the transceiver IC, antenna, matching network, crystal oscillators, and required passive components into a single certified PCB module. By offloading the RF section, BLE modules let product teams focus on firmware, sensors, and application logic rather than impedance matching, shielding, and regulatory pre-compliance testing. Within the broader taxonomy, a BLE module sits above a bare BLE transceiver IC and below a fully integrated SoC-based product; it is part of the wireless module family within RF & Wireless and is closely related to other AIROC and EZ-BLE module families from Infineon/Cypress. Key features of the CYBLE-012011-00 include a low deep-sleep current of 60 nA (with GPIO or XRES wakeup), programmable output power up to +9 dBm, and receive sensitivity of approximately -92 dBm in standard BLE mode. The onboard PSoC 4 BLE supports Cypress/PSoC Creator and ModusToolbox IDEs with a complete BLE Component and profile library. Integrated shield and regulatory certifications (FCC, IC, CE, MIC) eliminate the need for end-product RF testing for most regions. The CYBLE-012011-00 shares its module pin footprint and PSoC 4 BLE silicon datasheet with the uncertified CYBLE-012012-10 variant; the 012012-10 omits the RF shield and Bluetooth SIG listing, exposing the same GPIOs and pinout, making it a drop-in footprint alternative for prototypes that will go through self-certification. The host interface uses standard UART, SPI, or I2C, and the module runs from a single 1.8 V to 5.5 V supply rail. Typical applications include wireless sensor nodes for industrial IoT, BLE beacons for retail and asset tracking, fitness and medical wearables, smart-home hubs, remote controls, and HID peripherals such as mice, keyboards, and stylus devices. The 23 GPIOs and analog peripherals also support direct sensor readout without an external MCU. When replacing bare-chip designs with a module, expect to save 6-9 months of PCB iteration and regulatory certification effort, and budget approximately 200 mm² of host-board keep-out area for the antenna pattern.
CYBLE-022001-00 - Bluetooth LE 4.1 PSoC 4 Module 128 KB | Infineon
The Infineon CYBLE-022001-00 is a fully certified, turnkey Bluetooth Low Energy (BLE) module integrating a Cypress PSoC 4 BLE programmable MCU with 128 KB of flash memory, 16 KB of SRAM, and an onboard 2.4 GHz ceramic chip antenna, all housed in a compact 10 x 10 x 1.80 mm surface-mount package. An RF transceiver module (also called an RF module or BLE module) is a pre-certified subsystem that bundles a radio IC, matching network, crystal, antenna, and optional microcontroller into a single tested hardware unit, eliminating the need for designers to qualify the RF chain themselves. The CYBLE-022001-00 sits in the RF & Wireless > RF Modules subcategory of the broader Power/Connectivity semiconductor ecosystem and supports Bluetooth v4.1 LE with a 1 Mbps air data rate over the 2.4 GHz ISM band. Key features include 16 configurable GPIOs (with exposed ADC, PWM, UART, SPI, and I2C peripherals), an integrated ARM Cortex-M0 core, -92 dBm RX sensitivity for extended range, and up to +3 dBm programmable TX output power. Module-level FCC/IC/CE/MIC regulatory certifications substantially reduce end-product qualification time. Architecture depth: The module is built around the Infineon PSoC 4 BLE silicon (CYBL1XX7X family), which combines a 32-bit ARM Cortex-M0 CPU, configurable analog and digital blocks (the famous PSoC UDB/PLD fabric), CapSense touch support, and a 2.4 GHz radio. An onboard 32 kHz watch crystal and a 24 MHz main crystal are included, plus all RF matching components and the chip antenna. Flash is 128 KB, SRAM is 16 KB. Typical applications include BLE beaconing wearables, wireless HID peripherals (keyboards/mice/remote controls), industrial sensor telemetry nodes, smart-home lighting controllers, medical device accessory links, and proximity/marketing beacons where a small, certified, low-power radio drop is required. Design consideration: Because the module is pre-certified, no antenna-matching network is required - the user PCB only needs to expose the 10 x 10 mm land pattern and reserve adequate clearance around the antenna keep-out zone to maintain radiated performance. This page synthesizes distributor pricing, drop-in compatible module variants (CYBLE-222005-00, CYBLE-222014-01), and practical design notes not found in the manufacturer datasheet alone.
CYBLE-222014-01 - Bluetooth 4.2 LE Module, 256KB Flash | Infineon
The Infineon CYBLE-222014-01 is a fully certified, programmable Bluetooth Low Energy (BLE) v4.2 transceiver module based on the Cypress PSoC 4 BLE / PRoC BLE platform, housed in a compact 10 x 10 x 1.80 mm surface-mount module with an integrated chip antenna. It is built around an Arm Cortex-M0 core, integrates 256 KB of flash memory and 32 KB of SRAM, operates from 1.9 V to 5.5 V supply, and provides up to 16 GPIOs alongside ADC, timers, PWM, and serial interfaces (I2C, UART, SPI). An EZ-BLE module is a fully integrated, regulatory-certified Bluetooth Low Energy (BLE) turnkey solution that combines a Bluetooth radio, microcontroller, crystal oscillators, passive components, and a chip antenna into a single reflow-solderable package, eliminating the need for RF design expertise and significantly accelerating wireless product development. Key features include a royalty-free BLE stack compatible with Bluetooth 4.2 (and stack-upgradable to Bluetooth 5.x on compatible parts), an integrated 2.4 GHz transceiver with on-module chip antenna, up to 16 GPIOs, four serial communication blocks, four TCPWMs, an ADC, and onboard 32 kHz and main crystals. The module includes built-in security features and supports in-system programming via SWD. Architecturally, the CYBLE-222014-01 leverages Cypress's PSoC 4 programmable system-on-chip with CapSense touch-sensing capability, enabling flexible peripheral routing and capacitive touch buttons or sliders without external components. The integrated chip antenna is impedance-matched on the module, so designers can avoid the most common cause of BLE range failures: a poorly matched PCB trace antenna. Typical applications include IoT sensor nodes, BLE beacons, fitness and wearable devices, smart-home actuators, industrial wireless sensors, and any compact battery-powered product that needs certified wireless connectivity without an RF layout cycle. When designing with this module, follow Infineon's reference antenna keep-out region on the host PCB around the chip antenna, supply the module with a clean 1.9 V to 5.5 V rail with a decoupling cap within 5 mm of the VBAT pin, and verify regulatory output power limits in your target market. This page synthesizes distributor pricing, drop-in compatible module alternatives, and practical RF layout notes specific to the CYBLE-222014-01 that the Infineon datasheet alone does not surface, helping engineers compare candidates quickly.
CYBT-273063-02 - BT 5.0 Module U.FL, Cortex-M4 | Infineon
The Infineon Technologies CYBT-273063-02 is a certified AIROC Bluetooth v5.0 transceiver module for the 2.4 GHz ISM band, built around an Arm Cortex-M4 host processor with 256 KB flash and 176 KB RAM, housed in a 12.5 x 19 mm surface-mount LGA-style package with a U.FL connector for an external antenna. A Bluetooth module is an RF transceiver subsystem that integrates a radio, baseband, antenna interface, and a programmable host MCU into a single pre-certified unit. Modules occupy the upper tier of the wireless-connectivity hierarchy (semiconductor -> RF transceiver IC -> Bluetooth SoC -> Bluetooth module -> end device), letting OEMs add Bluetooth LE and BR/EDR connectivity without performing their own RF design or regulatory testing. Key features include Bluetooth 5.0 certification, an onboard Arm Cortex-M4 core executing user application code, 256 KB of flash for firmware and data storage, and 176 KB of RAM. The U.FL antenna connector supports a standard 2.0 dBi dipole antenna; per the Infineon EZ-BT module datasheet, any antenna of equivalent or less gain can be used without additional FCC application and testing. The EZ-BT module family shares a common footprint across antenna options: the CYBT-273063-02 uses a U.FL connector, the CYBT-263064-02 offers an RF solder-pad output, and the CYBT-263065-02 integrates a trace antenna. All three are pre-certified, reducing time-to-market for regulatory approval in North America and other regions. Typical applications include smart-home and IoT sensor nodes, industrial wireless gateways, point-of-sale and beacon hardware, and connected medical peripherals that require reliable 2.4 GHz connectivity with local processing headroom from the Cortex-M4 core. Design consideration: because the antenna is external, place the U.FL receptacle near the board edge, keep the 50-ohm transmission line short, and verify antenna placement away from ground planes and metal enclosures for optimal radiated performance. This page synthesizes distributor pricing, drop-in family alternatives, design notes, and AI-optimized technical FAQs not consolidated in the manufacturer datasheet.