USB Interface ICs
بەرهەمەکان (37)
SN75174DW - 4-Channel RS-422/RS-485 Driver | Texas Instruments
The Texas Instruments SN75174DW is a monolithic quadruple differential line driver with four independently enabled, three-state outputs, a 4.75 V to 5.25 V supply range, and operation up to 4 megabaud in a 20-pin SOIC package. It meets the requirements of ANSI EIA/TIA-422-B, RS-485, and ITU Recommendation V.11. A differential line driver is an interface IC that converts logic-level signals into balanced differential outputs for communication over cables or long printed-circuit-board traces. As a member of the RS-422 and RS-485 interface hierarchy, it translates a digital transmitter signal into noise-resistant differential voltage pairs. The four channels suit multipoint buses, industrial equipment, industrial-control systems, and legacy data ports where multiple bus nodes require controlled output states. The SN75174 provides four differential drivers and common enable and ground pins. Each driver uses a positive and negative output, while the three-state outputs support shared party-line buses by placing unused transmitters in a high-impedance state. Its balanced outputs reduce sensitivity to common-mode noise, and the wide positive and negative output common-mode voltage ranges make it suitable for noisy industrial environments. The device supports transmission rates up to 4 megabaud and is intended for balanced multipoint communication. This makes it appropriate for RS-422 and RS-485 systems where a transmitter must support multiple drivers on one bus. The common enable control can coordinate output states, but system design must prevent multiple drivers from actively driving the same pair simultaneously. Typical uses include industrial RS-485 buses, data acquisition equipment, telecommunications interfaces, instrumentation, computer peripherals, and embedded control systems. The 20-pin SOIC package supports conventional surface-mount assembly and is available as the SN75174DW ordering option identified by DigiKey as a 20-SOIC device. Designers should match cable termination, biasing, and transceiver direction-control requirements to the bus standard. Keep traces short where possible, provide a continuous ground reference where the interface standard permits it, and verify signal polarity and enable timing before enabling the outputs. The SN75174DW is a digital interface IC, so Safe Operating Area data do not apply.
SN75174DWR - 4-Channel RS-422/RS-485 Driver | Texas Instruments (Tape & Reel)
The Texas Instruments SN75174DWR is a monolithic quadruple differential line driver with four independently enabled, three-state outputs, a 4.75 V to 5.25 V supply range, and operation up to 4 megabaud in a 20-pin SOIC package. It meets the requirements of ANSI EIA/TIA-422-B, RS-485, and ITU Recommendation V.11. A differential line driver is an interface IC that converts logic-level signals into balanced differential outputs for communication over cables or long printed-circuit-board traces. As a member of the RS-422 and RS-485 interface hierarchy, it translates a digital transmitter signal into noise-resistant differential voltage pairs. The four channels suit multipoint buses, industrial equipment, industrial-control systems, and legacy data ports where multiple bus nodes require controlled output states. The SN75174 provides four differential drivers and common enable and ground pins. Each driver uses a positive and negative output, while the three-state outputs support shared party-line buses by placing unused transmitters in a high-impedance state. Its balanced outputs reduce sensitivity to common-mode noise, and the wide positive and negative output common-mode voltage ranges make it suitable for noisy industrial environments. The device supports transmission rates up to 4 megabaud and is intended for balanced multipoint communication. This makes it appropriate for RS-422 and RS-485 systems where a transmitter must support multiple drivers on one bus. The common enable control can coordinate output states, but system design must prevent multiple drivers from actively driving the same pair simultaneously. Typical uses include industrial RS-485 buses, data acquisition equipment, telecommunications interfaces, instrumentation, computer peripherals, and embedded control systems. The 20-pin SOIC package supports conventional surface-mount assembly and is available as the SN75174DWR ordering option identified by DigiKey as a 20-SOIC device. Designers should match cable termination, biasing, and transceiver direction-control requirements to the bus standard. Keep traces short where possible, provide a continuous ground reference where the interface standard permits it, and verify signal polarity and enable timing before enabling the outputs. The SN75174DWR is a digital interface IC, so Safe Operating Area data do not apply.
STUSB4531BJR - Standalone USB PD Sink Controller | ST
The STMicroelectronics STUSB4531BJR is a standalone USB Type-C and USB Power Delivery sink controller that negotiates up to five configurable Power Data Objects (PDOs) without any software support, housed in a 16-pin CSP (chip-scale package) rated for VBUS up to 23 V and operating from -40C to +105C. It supports dead battery mode, allowing battery-powered systems to charge from any battery state of charge, including a fully depleted battery (SOC = 0%). A USB PD sink controller is the device-side counterpart in a USB Type-C power negotiation: it communicates with a source (charger, dock, or power adapter) over the CC line using the USB PD protocol to agree on a voltage and current contract. Within the power-management hierarchy, it sits between the USB-C receptacle and the system power path, upstream of DC-DC converters and battery chargers, and is a key building block of modern USB-C power interface ICs. Key features include fully standalone autorun operation with a default PDO configuration stored in internal non-volatile memory, proprietary negotiation algorithms that secure a power contract without a host MCU, dead battery operation powered directly from the VBUS receptacle pins, and a wide 23 V VBUS tolerance that removes the need for external front-end protection in many designs. The STUSB4531 implements its negotiation state machines in dedicated hardware, so it continues operating even when the application processor is asleep or unpowered. The hybrid mode allows an application MCU to monitor or adjust the negotiation, giving designers both autonomy and flexibility. Typical applications include USB-C powered accessories, power banks, portable and wearable devices, battery-powered industrial sensors, and any sink-side system that must charge reliably from a fully depleted battery. Design consideration: because the device is powered from VBUS receptacle pins, ensure the CC line ESD and VBUS discharge timing follow the reference design layout for robust hot-plug behavior. This page adds value beyond the ST datasheet by synthesizing distributor pricing context, same-family drop-in alternatives, and practical design notes in one place.
TCAN1473A-Q1 - SIC CAN FD Transceiver 8Mbps | Texas Instruments
The Texas Instruments TCAN1473A-Q1 is an automotive-grade, high-speed CAN transceiver meeting the physical layer requirements of ISO 11898-2:2024 including Signal Improvement Capability (SIC). It supports classical CAN and CAN FD data rates up to 8 Mbps in a 14-pin VSON (4.5x3 mm) DMT package. A CAN transceiver is the physical-layer interface between a CAN protocol controller and the twisted-pair bus, converting controller logic into differential signals and vice versa while providing drive strength, receiver thresholding, and fault protection. Within the interface IC hierarchy, the TCAN1473A-Q1 sits alongside LIN and FlexRay transceivers in automotive networking systems. Key features include SIC functionality, which actively shapes bus signals to reduce ringing at dominant-to-recessive edges, lowering electromagnetic emissions and enabling 2 Mbps, 5 Mbps, or 8 Mbps operation in large networks with unterminated stubs. The device integrates a low-power Sleep mode, an SWE timer that safely transitions to Sleep after tINACTIVE inactivity in Standby mode, and INH and WAKE pins for system power control. Protection includes thermal shutdown and bus fault tolerance, with AEC-Q100 qualification. According to the TI datasheet, the TCAN1473A-Q1 is pin compatible with classical CAN FD transceivers such as TCAN1043A-Q1, TCAN1043-Q1, and TCAN1043N-Q1, simplifying upgrades of existing designs to SIC without PCB changes. Typical applications include body electronics and lighting, automotive gateways, ADAS domains, infotainment and cluster, hybrid/electric powertrain systems, e-bikes, and industrial transportation. Design consideration: optimize bus termination and common-mode choke placement; SIC improves margin on long stubs, but proper PCB layout and grounding remain essential for best EMC performance.
TJA1021TK/20/C - 20 kBd LIN Transceiver | NXP
The NXP TJA1021TK/20/C is an automotive LIN physical-layer transceiver supporting communication from 1 kBd to 20 kBd in an 8-pin HVSON package measuring 3 x 3 mm. It interfaces a LIN commander or responder protocol controller with the physical LIN bus, integrates a voltage regulator, and supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 communication. A LIN transceiver is a physical-layer interface IC within the broader automotive network-controller hierarchy. A microcontroller or dedicated LIN controller generates serial transmit data, while the transceiver converts that logic-level signal into a waveform suitable for the single-wire LIN bus. It also receives the bus waveform and converts it back into a logic signal that the protocol controller can interpret. The TJA1021TK/20/C provides optimized slew-rate control and waveform shaping to reduce electromagnetic emissions. It is pin-compatible with the TJA1020 and MC33662B families and has an improved electrostatic-discharge specification relative to the TJA1020. The integrated regulator reduces the external power-supply requirements of the transceiver. Its 20 kBd limit supports modern in-vehicle subnetworks while retaining compatibility with lower LIN baud rates down to 1 kBd. The /20 variant is intended for LIN networks operating at rates up to 20 kBd. The HVSON-8 package provides a compact surface-mount footprint and an exposed thermal pad for heat dissipation. Because a LIN bus is a single-wire network, its transceiver must coordinate transmitter dominance, receiver thresholds, bus termination, waveform control, and fault behavior while allowing multiple nodes to share the same communication channel. Typical uses include LIN master modules, LIN slave controllers, body-control modules, door modules, seat modules, climate-control interfaces, switch panels, automotive lighting controllers, and other low-speed vehicle subnetworks. The part is particularly suitable where compact placement, standardized LIN behavior, low electromagnetic emissions, and direct compatibility with existing TJA1020-class hardware are important. Design the LIN bus according to the NXP datasheet, including the specified transceiver input and output capacitors, bus termination, pull-up arrangement, wiring topology, and exposed-pad soldering. Maintain the required headroom between the battery-side supply and the LIN bus level, and validate EMC behavior in the finished vehicle harness because cable geometry and termination can affect edge quality. This page combines protocol compatibility, package details, verified sourcing information, drop-in alternatives, and practical integration guidance. It also identifies where design data must be checked against the manufacturer datasheet, helping engineers move from component selection to LIN network implementation more efficiently.
TJA1085GHN/0Z - FlexRay Active Star Coupler 4-Branch | NXP
The NXP Semiconductors TJA1085GHN/0Z is a FlexRay active star coupler that connects up to 4 branches of a FlexRay vehicle network, housed in a 44-pin HVQFN (9x9 mm) package. It is compliant with the FlexRay electrical physical layer specification V3.0.1 and ISO 17458-4, providing the signal regeneration and galvanic branch isolation required in fault-tolerant automotive x-by-wire and advanced driver assistance backbone networks. An active star coupler is a network topology device that receives signals on one branch, regenerates them, and retransmits them on the remaining branches. Unlike passive coupling, active star topology means a short circuit or fault on one branch does not disable the entire FlexRay bus, because the coupler electrically decouples each branch. In the automotive in-vehicle networking hierarchy, the TJA1085G sits at the physical-layer level above simple linear bus transceivers, serving as the backbone node of safety-critical, time-triggered communication systems. Key features include support for 4 FlexRay branches with TRXD0/TRXD1 receive interfaces that allow several TJA1085G devices to be cascaded for networks requiring more branches, a dedicated Communication Controller (CC) interface for direct attachment to the FlexRay communication controller, and full compliance with FlexRay V3.0.1/ISO 17458-4 timing and electrical requirements. The HVQFN-44 package with its exposed pad provides low inductance and good thermal performance for the sustained drive currents needed to power four actively driven branches. Architecturally, the device integrates receiver, driver, and supervision logic per branch, detecting branch faults and isolating defective stubs so the healthy portion of the network keeps operating. Because FlexRay is a time-triggered protocol with deterministic 10 Mbit/s communication, the coupler's loop-through delay and signal symmetry directly affect the network's static segment timing budget, which the TJA1085G meets within the V3.0.1 specification limits. Typical applications include chassis-domain FlexRay backbones in premium vehicles, x-by-wire systems (steer-by-wire, brake-by-wire), advanced driver assistance sensor fusion rings, and gateway modules that aggregate multiple FlexRay branches. Design consideration: provide a low-impedance ground path via the exposed die pad and observe branch-wiring stub length limits per ISO 17458-4 to preserve signal integrity at 10 Mbit/s. This page adds value beyond the manufacturer datasheet by consolidating distributor pricing, availability, package data, and application guidance in one AI-optimizable reference.
TJA1086GHN/0Z - FlexRay Active Star Coupler 2 Branch | NXP
The NXP Semiconductors TJA1086GHN/0Z is a FlexRay active star coupler that connects two branches of a FlexRay network, housed in a 44-pin HVQFN (9 x 9 mm) package. It is compliant with the FlexRay electrical physical layer specification V3.0.1 / ISO 17458-4 and supports data rates up to 10 Mbit/s, the maximum rate defined by the FlexRay communications system. An active star coupler is a network topology element used in automotive and industrial in-vehicle networks. Unlike a passive star, which simply splits the bus signal, an active star receives a frame on one branch, regenerates it, and re-transmits it to all other branches. This regeneration decouples electrical faults on one branch from the rest of the network, improving fault containment, signal integrity, and overall network robustness. In the hierarchy of in-vehicle networking ICs, the TJA1086G sits above simple bus line transceivers (such as FlexRay node transceivers) and belongs to the class of network interface and communication ICs. Key features include full-duplex point-to-point branch links, TRXD0/TRXD1 receiver interfaces that allow several TJA1085G and TJA1086G devices to be cascaded to increase the number of branches in the network, and branch-related fault handling so a short or low-ohmic fault on one branch does not take down the whole star. The 44-HVQFN package with an exposed thermal pad provides low inductance and good thermal dissipation for the 9 x 9 mm footprint. Technically, the device implements the analog front end and control logic needed to drive and receive FlexRay differential signals on each branch at 10 Mbit/s, with wake-up and sleep handling compatible with the FlexRay electrical physical layer. The /0Z ordering suffix identifies the standard grade and tape-and-reel delivery of this silicon. Moisture sensitivity level is MSL 1 with a 260 C peak reflow rating, simplifying SMT assembly. Typical applications include chassis and body-domain FlexRay stars in passenger cars, gateway nodes aggregating multiple FlexRay branches, and safety-critical backbone networks where deterministic 10 Mbit/s communication with dual-channel redundancy is required. When designing with this part, route each FlexRay branch as a matched differential pair and observe the bus termination guidelines of the FlexRay electrical physical layer specification; verify supply and enable pin configurations against the latest NXP datasheet before layout sign-off. This page synthesizes distributor pricing references, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone.
TLE6251GNTMA1 - 1 Mbit/s CAN Transceiver | Infineon
Infineon Technologies TLE6251GNTMA1 is a 5 V high-speed CAN bus transceiver with sleep and standby operating modes, supplied in a 14-terminal PG-DSO-14-13 surface-mount package. Verified distributor data identifies the device as a 1/1 full CANbus transceiver, while application listings describe the TLE6251 family as a high-speed CAN transceiver supporting data rates up to 1 Mbit/s. Its principal role is to connect a host controller to a CAN network through a differential transmit and receive interface. A CAN transceiver is a physical-layer interface IC within the Controller Area Network ecosystem. The broader hierarchy is CAN transceiver, CAN interface IC, bus transceiver, interface IC, and semiconductor. A CAN controller generates and interprets CAN frames, while the transceiver converts that logical information into the CANH and CANL differential bus signals required for reliable, noise-resistant communication between automotive, industrial, and embedded systems. Verified product information highlights several useful characteristics. The TLE6251GNTMA1 operates from a 5 V supply, supports a maximum CAN data rate of 1 Mbit/s, and provides sleep and standby modes for reduced power use. It is described as a full-duplex CAN interface, meaning the transceiver supports both transmission onto the bus and reception from the bus. The 14-terminal PG-DSO-14-13 package is a surface-mount gull-wing package based on the listed SOP configuration. The sleep and standby functions are central to its power-management behavior. Standby permits the device to remain available for bus-related activity, while sleep supports a lower-power network state. Exact threshold values, current consumption, loopback behavior, bus fault reporting, and timing limits should be confirmed in the Infineon manufacturer datasheet before a design is released; those detailed values were not present in the supplied verification records. TLE6251GNTMA1 is suitable for automotive control modules, body and comfort electronics, industrial automation equipment, robotics controllers, diagnostic interfaces, and embedded CAN gateways. In a typical design, a CAN controller connects to the transceiver logic pins, while CANH and CANL connect to the physical bus. Termination is normally placed at both ends of the bus rather than at every node. PCB implementation requires correct routing of the differential bus pair, a solid ground reference, suitable supply decoupling, and compliance with the isolation and termination requirements of the selected CAN network. The bus conductors should be kept as a controlled-impedance pair, with minimal stubs and branching, because connector branches and excessive trace length can degrade signal integrity at the supported 1 Mbit/s class of operation. This product record combines verified distributor identification, family-level CAN features, package information, cross-reference findings, and practical design guidance. It also distinguishes the TLE6251 family options that require datasheet-level confirmation before being treated as drop-in replacements, providing useful context beyond a distributor listing or a basic catalog entry.
TUSB213RGYR - USB 2.0 HS Redriver with DC Boost | Texas Instruments
Texas Instruments TUSB213RGYR is a USB 2.0 high-speed signal conditioner with DC boost, optimized for restoring degraded USB data pairs across lossy interconnect. The device supports USB 2.0 high-speed, USB 2.0 OTG 2.0, and Battery Charging 1.2 operation, with one configurable high-speed data channel. Its 4.4 V to 5.5 V supply range and 14-pin VQFN package in a compact 3.5 mm by 3.5 mm footprint suit space-constrained USB ports, cable assemblies, docking systems, and embedded host or device designs. A USB redriver is a signal-processing interface integrated circuit placed between a USB transmitter and receiver. It detects degradation on a high-speed differential pair and applies selectable equalization to restore eye opening. Unlike a repeater or hub controller, the TUSB213 does not interpret USB packets or maintain device firmware; its primary role is analog signal recovery between the USB PHY and connector. The TUSB213 provides pin-strap or I2C configuration for low-speed, full-speed, and high-speed signaling. Four selectable AC boost settings allow the equalization to be tuned for different interconnect losses. Its disconnect and shutdown functions can reduce power consumption when a port is inactive. The device also supports daisy chaining to address high-loss channels, and interchangeable D1P/M and D2P/M routing helps simplify board planning. According to the Texas Instruments TUSB213 product page, the redriver is compatible with USB 2.0, OTG 2.0, and BC 1.2. It can support up to 5 meters of pre-channel cable length or 2 meters of post-channel cable length. These figures describe intended channel reach rather than a guarantee for every cable, connector, PCB, or environmental condition. Typical uses include USB Type-C and legacy USB-A ports, external storage, docking stations, cameras, test equipment, and industrial control panels. The DC-boost function can add a controlled DC component to a differential data signal, while selectable AC boost compensates high-frequency attenuation. Correct implementation requires preserving controlled-impedance routing between the source PHY, redriver, connector, and receiving PHY. Design the power rails so they remain within the 4.4 V to 5.5 V operating range, and place the redriver close to the connector when loss occurs mainly in cable or connector transitions. Configure boost through pins or I2C, evaluate eye closure with the intended channel, and verify low-speed and full-speed bypass behavior after high-speed equalization is enabled. This page combines the manufacturer feature set, packaging information, ordering variants, drop-in alternatives, application guidance, and design considerations into one engineering-focused reference. It also provides a parameter comparison to help assess whether a same-package variant is appropriate for a specific USB channel.
TUSB215RGYT - USB 2.0 HS Signal Conditioner | Texas Instruments
Texas Instruments TUSB215RGYT is a USB 2.0 high-speed signal conditioner with DC boost, integrated USB BC1.2 Charging Downstream Port (CDP) functionality, and VBUS supply. The device supports USB 2.0, OTG 2.0, and BC1.2 operation, and it is designed for Low-Speed, Full-Speed, and High-Speed USB signaling. It provides a 480 Mbit/s USB high-speed interface capability in a 14-pin VQFN RGY package. A USB signal conditioner is an interface IC that restores signal integrity through lossy interconnect while adding the functions required by a USB port. The TUSB215 family is intended for systems where cable loss, connector transitions, PCB routing, or other channel impairments can degrade USB data signals. Its support for host or device use and interchangeable D+ and D− data paths makes it useful across common USB port architectures. The TUSB215RGYT includes DC boost, an integrated CDP, and a VBUS supply. Its USB BC1.2 CDP controller can be configured by pin strap or I²C, providing a practical way to identify a downstream-facing port and coordinate charging behavior. The device also supports daisy chaining, which can extend reach in high-loss applications. TI specifies support for up to 5 m of pre-channel cable or 2 m of post-channel cable. The device supports low-speed, full-speed, and high-speed signaling. Its dual data-path implementation permits D1P/M and D2P/M interchangeability, reducing sensitivity to which host or device lane is connected. This is particularly useful in reusable equipment, docking systems, and port designs where source and sink roles can change. Typical uses include USB 2.0 docking stations, laptop and tablet accessories, industrial data acquisition equipment, peripheral interfaces, and test systems. The integrated CDP and VBUS functions can simplify a compliant USB port design, while the signal-conditioning stage is intended to preserve data integrity over longer or less controlled interconnect. PCB implementation should preserve the high-speed differential pair as a controlled-impedance route and place decoupling close to the supply pins. Review the pin-description and layout guidance in the manufacturer datasheet before assigning tracks or selecting external components. Verify that the selected cable length and channel placement comply with the device’s stated pre-channel and post-channel limits.
TUSB8041IPAPQ1 - 4-Port USB 3.0 Hub AEC-Q100 | Texas Instruments
The Texas Instruments TUSB8041IPAPQ1 is an automotive-grade four-port SuperSpeed USB 3.0 hub controller delivering 5-Gbps data rates on the upstream port and SuperSpeed, high-speed, full-speed, or low-speed connections on the four downstream ports, housed in a 64-pin HTQFP (PAP, 10x10 mm) package with exposed pad and qualified to AEC-Q100 for automotive applications. A USB hub controller is a dedicated interface IC that fans a single USB upstream connection out to multiple downstream ports while managing enumeration, power distribution, battery-charging handshakes, and protocol translation between USB 3.0 (SuperSpeed) and USB 2.0 (high/full/low speed) device populations. Hub controllers sit within the broader USB interface IC family inside the system I/O hierarchy of a compute module, head unit, or docking platform. Key features include simultaneous SuperSpeed and high-speed/full-speed operation on the upstream port, per-port USB 2.0/3.0 downstream connectivity, dual supply rails of 1.1V and 3.3V, and flexible configuration. Configuration is possible via pin straps, OTP ROM, an I2C EEPROM, or an I2C/SMBus slave interface for custom PID, VID, and port/PHY settings, with GPIO available for status and control. The device uses TI hub controller architecture that maintains 5-Gbps SuperSpeed signaling integrity while supporting battery charging strap options. Because the USB 3.0 link is handled natively, downstream traffic between mixed-speed devices is scheduled efficiently without bottlenecking SuperSpeed devices on a USB 2.0 path. Typical applications include automotive infotainment head units and telematics modules, industrial PCs and HMI panels, and docking stations or self-powered desktop hubs. The AEC-Q100 qualification makes it particularly suited to vehicle environments with wide temperature and load-dump conditions. Design consideration: supply sequencing and the 24-MHz reference clock layout dominate success with SuperSpeed hubs; keep crystal traces short and follow the TI reference design for the PAP package thermal pad grounding. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
USB2514BI-AEZG - 4-Port USB 2.0 Hub Controller | Microchip (Tape & Reel)
The Microchip Technology USB2514BI-AEZG is a 4-port USB 2.0 Hi-Speed hub controller with 480 Mbps throughput, a 3.3 V supply, and an integrated Multi Transaction Translator (MTT), housed in a 36-pin QFN (6x6 mm) package with exposed pad. It belongs to the Microchip USB251xB/xBi family of low-power, configurable hub controller ICs for embedded USB solutions. A USB hub controller is an interface IC that fans out a single upstream USB port into multiple downstream ports, handling enumeration, transaction translation between USB 2.0 Hi-Speed (480 Mbps) and Full-/Low-Speed (12/1.5 Mbps) devices, and power management for each port. Within the system hierarchy, it sits in the USB protocol layer between a host controller and the downstream peripherals, making it a critical building block in embedded USB solutions, docking stations, and instrumentation front ends. Key features include MultiTRAK technology, which assigns an independent transaction translator to every downstream port so mixed-speed devices do not block each other; I2C/SMBus and strapping-pin configuration options; industrial temperature support from -40C to +85C on the BI variant; and integrated battery-charging support on family members. Flexible OEM configuration via an external EEPROM or SMBus allows custom VID/PID, string descriptors, and port mapping without firmware development. Architecturally, the device leverages Microchip MultiTRAK technology for industry-leading data throughput in mixed-speed USB environments, and per Microchip documentation the family members are pin-compatible direct drop-in replacements for one another, using the same PCB components. The 36-QFN exposed-pad package supports good thermal and ground integrity for the 480 Mbps PHY. Typical applications include industrial USB ports on factory equipment and PLCs, medical instrument and test-equipment front panels, PC peripherals and docking hardware, and embedded host expansion in automotive-adjacent industrial systems that need robust USB connectivity. Design consideration: use the industrial-grade BI variant only if the full -40C to +85C range is required; the commercial B variant may reduce cost where 0C to 70C suffices, and both are pin-compatible drop-ins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
USB2514BI-AEZG-TR - 4-Port USB 2.0 Hub Controller | Microchip
The Microchip Technology USB2514BI-AEZG-TR is a 4-port USB 2.0 Hi-Speed hub controller with 480 Mbps throughput, a 3.3 V supply, and an integrated Multi Transaction Translator (MTT), housed in a 36-pin QFN (6x6 mm) package with exposed pad. It belongs to the Microchip USB251xB/xBi family of low-power, configurable hub controller ICs for embedded USB solutions. A USB hub controller is an interface IC that fans out a single upstream USB port into multiple downstream ports, handling enumeration, transaction translation between USB 2.0 Hi-Speed (480 Mbps) and Full-/Low-Speed (12/1.5 Mbps) devices, and power management for each port. Within the system hierarchy, it sits in the USB protocol layer between a host controller and the downstream peripherals, making it a critical building block in embedded USB solutions, docking stations, and instrumentation front ends. Key features include MultiTRAK technology, which assigns an independent transaction translator to every downstream port so mixed-speed devices do not block each other; I2C/SMBus and strapping-pin configuration options; industrial temperature support from -40C to +85C on the BI variant; and integrated battery-charging support on family members. Flexible OEM configuration via an external EEPROM or SMBus allows custom VID/PID, string descriptors, and port mapping without firmware development. Architecturally, the device leverages Microchip MultiTRAK technology for industry-leading data throughput in mixed-speed USB environments, and per Microchip documentation the family members are pin-compatible direct drop-in replacements for one another, using the same PCB components. The 36-QFN exposed-pad package supports good thermal and ground integrity for the 480 Mbps PHY. Typical applications include industrial USB ports on factory equipment and PLCs, medical instrument and test-equipment front panels, PC peripherals and docking hardware, and embedded host expansion in automotive-adjacent industrial systems that need robust USB connectivity. Design consideration: use the industrial-grade BI variant only if the full -40C to +85C range is required; the commercial B variant may reduce cost where 0C to 70C suffices, and both are pin-compatible drop-ins. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.