Analog Devices

AD8011ANZ - 328MHz Low-Power Current Feedback Amp | Analog Devices

MPN: AD8011ANZ ✓ چالاک
+5 V or ±5 V Vdss 8-PDIP Package
MOQ: 1 |

AD8011ANZ گشتی

The Analog Devices AD8011ANZ is a very low-power, high-speed current-feedback amplifier designed for operation from +5 V or ±5 V supplies. It is a single-circuit device in an 8-PDIP package, combining wide bandwidth, low distortion, and low power consumption for general-purpose signal amplification. The AD8011 is suitable as a general-purpose amplifier and can also replace higher-power high-speed amplifiers when its lower power consumption is acceptable. According to the manufacturer product information, the amplifier provides gain flatness of 0.1 dB to 25 MHz.

A current-feedback amplifier is a voltage-feedback amplifier architecture whose bandwidth and stability behavior are strongly influenced by feedback impedance rather than by a fixed closed-loop gain bandwidth. This architecture is widely used for video, instrumentation, signal-conditioning, and communications applications where high-speed operation and predictable gain-bandwidth behavior are more important than unity-gain stability. The AD8011 is therefore positioned between general-purpose precision amplifiers and very-high-power RF amplifiers.

The AD8011ANZ operates from +5 V or ±5 V supplies and is designed around a current-feedback topology for high-speed signal amplification. Its key strengths include wide bandwidth, low distortion, and very low power consumption. The 8-PDIP package provides through-hole assembly compatibility for industrial, instrumentation, and legacy equipment designs. The manufacturer describes the device as a general-purpose amplifier and as a possible replacement for high-speed amplifiers that consume more power.

The AD8011 is appropriate for video signal paths, instrumentation amplifiers, communication interfaces, analog front ends, and other applications requiring high-frequency amplification. Because current-feedback amplifiers depend on feedback-component selection, engineers should use the resistor and capacitor values recommended in the manufacturer datasheet rather than transplanting feedback networks from unrelated amplifier families.

For PCB implementation, keep feedback-loop connections short and place the input, output, feedback, and decoupling connections with attention to high-current return paths. The AD8011ANZ is a through-hole device, so its package requires adequate board spacing, pin-clearance planning, and mechanical verification against the target enclosure and connector layout.

This product page combines manufacturer application information, distributor package confirmation, lifecycle context, drop-in alternatives, and practical design guidance to support component selection, board layout, and sourcing decisions.

جێگرەوەکانی جێگۆڕکێ بۆ AD8011ANZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

AD8011AN

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP
AD8011 family variant with the same 8-PDIP package; ordering suffix differs from AD8011ANZ

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

AD8011ANC

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP
AD8011 family variant with the same 8-PDIP package; ordering suffix differs from AD8011ANZ

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

AD8012

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP
AD8012 shares the AD8011 current-feedback family and 8-PDIP format, with performance and supply details differing by device

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

AD8013

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP
AD8013 is a related current-feedback amplifier in the 8-PDIP family, with device-specific bandwidth and power characteristics

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

AD8014

✅ جێگرەوەی ڕاستەوخۆ
📦 8-PDIP
AD8014 is a related current-feedback amplifier in the 8-PDIP family, with device-specific bandwidth and power characteristics

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

AD8011ANZ زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Type Current Feedback Amplifier
Number of Circuits 1 circuit
ڤۆڵتیەی دابینکردن +5 V or ±5 V
پاکێج 8-PDIP
تۆپۆلۆژی Current feedback
Gain Flatness 0.1 dB to 25 MHz
Bandwidth 328 MHz
Power Consumption Very low power
Signal Type Single-ended
جۆری دامەزراندن Through-hole
دۆخی RoHS RoHS-compliant
Lead-Free Status Lead-free
Green Packaging Green electronic component

ڕێنمایی ڕێکخستنی پینی AD8011ANZ 8-pdip

ڕێکخستنی پین بۆ AD8011ANZ (پاکێجی 8-pdip). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 8-pdip بۆ AD8011ANZ

هیچ داتای وردی پینئاوت بەردەست نییە بۆ AD8011ANZ.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

AD8011ANZ گونجاوە بۆ 6 بەکارھێنانs: High-Speed Video Signal Conditioning, Instrumentation and Sensor Front Ends, Communications Receive Chains, Analog-to-Digital Converter Drive, Low-Power Instrumentation Signal Buffers, Pulse and Transient Signal Conditioning.

📺

High-Speed Video Signal Conditioning

The AD8011ANZ is well suited to video signal-conditioning stages that require wide bandwidth and low power consumption from a +5 V or ±5 V supply. Its current-feedback architecture and 0.1 dB gain-flatness specification to 25 MHz provide the bandwidth needed to preserve fast video edges, while the manufacturer describes the device as a low-power high-speed video amplifier. Place the AD8011 near the video source or receiving buffer, use the recommended feedback resistor for the intended gain, and keep the feedback trace short. Verify output settling and distortion in the target video format because source impedance, cable loading, and the next-stage input capacitance can materially affect the practical response.

🏭

Instrumentation and Sensor Front Ends

The AD8011ANZ can serve as the first high-speed gain stage in an instrumentation or sensor front end when the sensor produces a fast analog waveform that must be conditioned before digitization. The 328 MHz bandwidth figure and 0.1 dB gain-flatness specification to 25 MHz make the device relevant to wideband measurement chains, while its very-low-power bias reduces the burden on portable or distributed acquisition systems. Use the manufacturer's recommended feedback network for the selected gain, terminate the source impedance correctly, and place supply-bypass capacitors close to the device. Check input common-mode range, output swing, and offset behavior against the sensor's operating range.

🌐

Communications Receive Chains

The AD8011ANZ is appropriate for low-power amplification within communications receive chains where a high-speed analog stage must operate before filtering, conversion, or demodulation. Its current-feedback topology supports wide bandwidth, and the manufacturer identifies the device as a general-purpose high-speed amplifier with low power consumption and low distortion. In a practical receiver, the amplifier can add gain close to the connector or antenna interface, reducing the amount of unwanted loss before subsequent filtering. Keep the input path and feedback loop compact, verify the return path against ground, and confirm the output drive against the next stage's impedance and capacitance.

🔧

Analog-to-Digital Converter Drive

The AD8011ANZ can provide the high-speed drive stage immediately preceding an ADC when the converter's sampling edge requires more bandwidth or lower distortion than a general-purpose op amp can deliver. Its 328 MHz bandwidth and gain flatness to 25 MHz allow the stage to preserve fast transitions, while the +5 V or ±5 V supply options simplify integration into mixed-signal equipment. Select the gain and feedback components from the manufacturer's ADC-driving guidance, place the amplifier close to the ADC input, and use a controlled return path to minimize clock and digital crosstalk. Validate settling, common-mode level, and output compliance against the ADC data sheet.

🧪

Low-Power Instrumentation Signal Buffers

The AD8011ANZ can replace a higher-power high-speed amplifier in instrumentation buffers where the system has a restricted supply budget but still requires wide bandwidth. Analog Devices specifically describes the AD8011 as a possible replacement for high-speed amplifiers consuming more power, which makes it relevant to portable measurement systems and compact laboratory equipment. The 8-PDIP package supports straightforward through-hole assembly and rework in legacy or industrial instruments. Use the recommended current-feedback network, preserve the manufacturer's recommended ground and bypass arrangement, and validate that the lower-power device still meets the required output swing, noise, and stability margins.

📡

Pulse and Transient Signal Conditioning

The AD8011ANZ is useful for amplifying short-duration pulses and fast transient signals where bandwidth determines whether the system preserves pulse edges. Its wide-band current-feedback architecture, combined with the manufacturer description of low distortion and very low power consumption, makes it a candidate for radar, test and measurement, and industrial pulse-processing circuits. The amplifier should be placed near the source to limit trace loss, with the feedback loop kept as short as possible. Verify rise time, overshoot, and settling with the actual source and load because the gain-bandwidth relationship of a current-feedback amplifier depends directly on the selected feedback impedance.

کورتەی بەرهەمە پێشنیارکراوەکان

AD8011AN Same-family 8-PDIP amplifier بەکارهێنراوە لە: High-Speed Video Signal Conditioning, Analog-to-Digital Converter Drive AD8012 Related current-feedback amplifier بەکارهێنراوە لە: High-Speed Video Signal Conditioning, Communications Receive Chains, Pulse and Transient Signal Conditioning AD8011ANC Same-family 8-PDIP amplifier بەکارهێنراوە لە: Instrumentation and Sensor Front Ends, Low-Power Instrumentation Signal Buffers AD8013 Related current-feedback amplifier بەکارهێنراوە لە: Instrumentation and Sensor Front Ends, Analog-to-Digital Converter Drive, Pulse and Transient Signal Conditioning AD8014 Related current-feedback amplifier بەکارهێنراوە لە: Communications Receive Chains, Low-Power Instrumentation Signal Buffers
What is the operating voltage of AD8011ANZ?
The AD8011ANZ operates from +5 V or ±5 V supplies, according to the Analog Devices product information. The single-ended operating arrangement gives designers the choice between a 5 V supply for lower-voltage systems and split supplies for bipolar signal levels. When using ±5 V, the amplifier has symmetrical headroom for positive and negative signal excursions, which is useful in video, instrumentation, and communications circuits. Confirm the selected supply configuration against the application circuit in the manufacturer datasheet before finalizing the bypass and biasing network.
Is the AD8011ANZ a voltage-feedback or current-feedback amplifier?
The AD8011ANZ is a current-feedback amplifier, as identified by the Analog Devices product page and distributor package records. Current-feedback amplifiers derive their high-speed performance from the impedance of the feedback network, so the recommended feedback resistor and compensation capacitor are central to achieving the target gain and stability. Engineers should follow the manufacturer datasheet values for each supported gain configuration rather than copying a feedback network from a conventional voltage-feedback amplifier.
What are the key specifications of AD8011ANZ that engineers should know?
The AD8011ANZ is a single-circuit, current-feedback amplifier in an 8-PDIP package, specified for +5 V or ±5 V operation. Analog Devices describes gain flatness of 0.1 dB to 25 MHz, while distributor product records identify the device as a high-speed, low-power video amplifier with a 328 MHz bandwidth figure. The combination of wide bandwidth and very low power consumption makes it useful where a higher-power high-speed amplifier would add unnecessary supply demand. Use the manufacturer datasheet for exact test conditions and full electrical limits.
Where can I download the AD8011ANZ datasheet PDF?
The official AD8011ANZ datasheet is available through the Analog Devices product page at https://www.analog.com/en/products/ad8011.html. Select the AD8011 data sheet from the product resources, then choose the PDF document for the complete electrical characteristics, recommended operating conditions, pin descriptions, and typical performance curves. The 8-PDIP package designation is confirmed in distributor product records. Because the exact document revision and page count can change, use the current manufacturer download rather than a cached third-party copy.
Where can I find the AD8011ANZ pinout?
The AD8011ANZ pinout is defined in the pin-description section of the Analog Devices manufacturer datasheet. The part is packaged as an 8-PDIP, so the physical package has eight through-hole pins, but the complete signal and power assignments should be taken from the current datasheet rather than inferred from similar amplifier families. When laying out a board, verify pin numbering orientation, the supply pins, the inverting and non-inverting inputs, and the output against the package drawing and schematic before fabrication.
What can replace the AD8011ANZ?
The closest same-family replacements identified for the AD8011ANZ are the AD8011AN and AD8011ANC, while the AD8012, AD8013, and AD8014 appear in the same manufacturer amplifier family as related alternatives. Whether any candidate is a true drop-in replacement depends on package, pin assignment, supply arrangement, gain configuration, and feedback-network requirements. Cross-reference search results identify compatible-equivalent and pin-to-pin replacement families, but engineers should verify the candidate datasheet and perform stability and distortion checks before substitution.
Is the AD8011ANZ suitable for video amplifier applications?
Yes, the AD8011ANZ is suitable for video amplification because it is a high-speed, low-power current-feedback amplifier with wide bandwidth and low distortion. The Analog Devices product information identifies it as a general-purpose amplifier, and distributor product records classify it as a high-speed, low-power video amplifier. It is particularly attractive when a video path must operate from +5 V or ±5 V without the higher power consumption of many conventional high-speed amplifiers. Verify settling behavior and gain accuracy against the video format and system tolerance requirements.
What is the difference between AD8011ANZ and AD8011AN?
AD8011ANZ and AD8011AN are variants of the Analog Devices AD8011 family, and both are associated with the 8-PDIP package family used for the AD8011ANZ. Their suffix codes identify different orderable device variants, so procurement should be based on the exact manufacturer part number and its ordering information. For a drop-in substitution, confirm that the candidate has the same pin assignment, supply configuration, operating-temperature range, gain stability, and recommended feedback components as the AD8011ANZ.
When should I choose AD8011ANZ over a higher-power high-speed amplifier?
Choose the AD8011ANZ when the design needs the combination of high-speed amplification, low distortion, and very low power consumption from a +5 V or ±5 V supply. The manufacturer explicitly positions the device as a possible replacement for high-speed amplifiers that consume more power. It is a strong choice for video, instrumentation, and general signal-conditioning paths where the system has a tight power budget. Choose a higher-power device instead only when the required output swing, load drive, noise, temperature range, or exact feedback behavior exceeds the AD8011ANZ ratings.
What is the AD8011ANZ used for in instrumentation and signal conditioning?
The AD8011ANZ is used as a high-speed, low-power gain stage in instrumentation and signal-conditioning circuits. Its current-feedback architecture supports wide bandwidth, while the 328 MHz bandwidth figure and 0.1 dB gain-flatness specification to 25 MHz make it relevant to circuits handling fast analog signals. The amplifier can sit before an ADC, between sensor-conditioning stages, or in a communications receive chain. Feedback components, input termination, and output loading must be selected from the datasheet examples for the intended gain.
Is AD8011ANZ in stock and what is its typical availability?
Distributor listings identify AD8011ANZ as an orderable Analog Devices amplifier, but stock and lead time change continuously by region and quantity. The part appears in DigiKey, Mouser, LCSC, and other distributor catalogs, with at least one listing reporting inventory. For a confirmed allocation, submit the required quantity, target date, and package suffix through the Request a Quote form on this page. The manufacturer product page should also be used to confirm current product status and any last-time-buy or lifecycle notices.
How much does AD8011ANZ cost?
Current commercial pricing for the AD8011ANZ is best obtained through the Request a Quote form on this page, because distributor inventory and volume breaks change by order quantity and purchasing date. The page links to current manufacturer and distributor product records for verification. Request a quote for the exact 8-PDIP ordering suffix, required quantity, and delivery target so the commercial team can confirm availability, lead time, and applicable volume pricing directly.
Where can I buy AD8011ANZ online?
AD8011ANZ is listed by major authorized distributors and is also available through XAIPART's sourcing channel. Use the Request a Quote form on this page to specify quantity, packaging preference, delivery location, and target date. The manufacturer product page and the linked distributor records can be used to confirm the 8-PDIP package, current product status, and technical documentation. Avoid selecting a similarly named AD8011 variant without checking the exact suffix and pin-compatible ordering information.
What is the lead time for AD8011ANZ?
The current lead time for AD8011ANZ depends on factory availability, distributor inventory, order quantity, and the requested delivery date. Because lead time is not a fixed catalog attribute, request a firm schedule through the Request a Quote form on this page and include your required quantity and ship-to location. The manufacturer product page and distributor listings can be checked for lifecycle status and current inventory, while the commercial team can confirm the allocation and production schedule for your order.
Is the AD8011ANZ RoHS compliant and lead-free?
The AD8011ANZ is identified as a RoHS-compliant, lead-free, and green electronic component in distributor product documentation. This means the device is manufactured within the stated restrictions on hazardous substances and is supplied in lead-free packaging for RoHS-compliant assemblies. RoHS compliance does not by itself determine automotive qualification, so projects requiring AEC-Q100 should verify that status separately. For final material compliance records, use the current Analog Devices product documentation and the distributor's declaration for the exact ordering code.
How should feedback resistors and capacitors be selected for AD8011ANZ?
Select the AD8011ANZ feedback resistor and optional compensation capacitor from the gain-versus-frequency tables and application circuits in the Analog Devices manufacturer datasheet. Because the device uses current feedback, changing the feedback impedance changes both bandwidth and stability, and values copied from another amplifier family may produce peaking or oscillation. Keep the feedback loop compact on the PCB, use the recommended bypass capacitance at the supplies, and verify the final gain stage with an oscilloscope for adequate phase margin across the intended signal and load range.

داتای سەرچاوەی ئەندازیاری بۆ AD8011ANZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the AD8011ANZ when the design requires a high-speed current-feedback amplifier with 328 MHz bandwidth, 0.1 dB gain flatness to 25 MHz, and very low power consumption from a +5 V or ±5 V supply. It is especially suitable for video, instrumentation, communications, and ADC-drive stages where replacing a higher-power amplifier is desirable. Select AD8011AN or AD8011ANC first when exact family continuity and the 8-PDIP package are the dominant requirements. Consider AD8012, AD8013, or AD8014 only after checking their individual bandwidth, power, supply, and feedback-network data against the required gain. A substitute is acceptable only when its pinout, supply arrangement, operating-temperature range, stability, output swing, and distortion requirements satisfy the original circuit. Because the alternatives come from the same manufacturer family, they are preferable to an unqualified cross-brand substitute, but each still requires datasheet verification.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە AD8011AN AD8011ANC AD8012 AD8013 AD8014
Package 8-PDIP 8-PDIP 8-PDIP 8-PDIP 8-PDIP 8-PDIP
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Amplifier Architecture Current Feedback Amplifier Current Feedback Amplifier Current Feedback Amplifier Current Feedback Amplifier Current Feedback Amplifier Current Feedback Amplifier

جیاکەرەوە سەرەکییەکان

  • Lower-power current-feedback amplification option (بەراورد بەAD8012)
  • Direct AD8011 family ordering continuity (بەراورد بەAD8013)
  • Gain-flat performance for fast video and analog paths (بەراورد بەAD8014)

تێبینییەکانی دیزاین

Do not treat a current-feedback amplifier like a unity-gain-stable voltage-feedback amplifier. The AD8011ANZ bandwidth and stability depend on the feedback impedance, so the feedback resistor and compensation capacitor must come from the manufacturer datasheet. Copying a feedback network from another amplifier can create peaking or instability even when the intended gain is identical.

Keep the forward and feedback paths physically short and connect the bypass capacitors directly to the supply and ground pins. High-frequency current should not flow through long traces or shared ground paths between the input, output, and feedback components. After layout, verify the implemented gain, peaking, settling, and output drive with the actual source and load rather than relying only on simulation.

Use the +5 V or ±5 V supply arrangement intended by the application and follow the manufacturer bypass recommendations. Because the AD8011 is specifically positioned as a lower-power replacement for higher-consumption high-speed amplifiers, power-supply capacity should still be checked for the configured supply voltage, output load, and board temperature. Avoid adding excessive decoupling capacitance directly across the supply pins, which can impair stability in some high-speed amplifier layouts.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

RoHS-compliant, lead-free, and green status is stated in distributor product documentation for AD8011ANZ. Automotive qualification, REACH status, halogen-free status, and conflict-minerals declarations require separate confirmation from the current manufacturer documentation.

داتا پشتڕاستکراوەتەوە لە: 2026-11-18 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

AD8011ANZ datasheet AD8011ANZ datasheet pdf AD8011ANZ pinout AD8011ANZ 8-PDIP AD8011ANZ current feedback amplifier AD8011ANZ 328MHz bandwidth AD8011ANZ video amplifier AD8011ANZ replacement AD8011ANZ equivalent AD8011ANZ vs AD8012 AD8011ANZ price AD8011ANZ stock Analog Devices AD8011ANZ AD8011 application circuit AD8011 5V low power amplifier

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices AD8011ANZ AD8011 AD8011AN AD8011ANC AD8012 AD8013 AD8014 current-feedback amplifier voltage-feedback amplifier operational amplifier signal-conditioning amplifier video amplifier 8-PDIP DIP package through-hole package surface-mount alternative gain flatness bandwidth feedback impedance low-distortion amplification low-power amplification instrumentation amplifier ADC driver RoHS lead-free packaging
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ