Texas Instruments

INA122PA - 60uA Micropower Instrumentation Amplifier, 36V | Texas Instruments

MPN: INA122PA ✓ چالاک
2.2 V to 36 V Vdss 60 uA Id 8-pin PDIP (P) Package
MOQ: 1 |

INA122PA گشتی

The Texas Instruments INA122PA is a single-channel, low-power instrumentation amplifier with 60 uA quiescent current, a 2.2 V to 36 V single-supply (or plus/minus 18 V dual-supply) operating range, and programmable gains from 5 V/V to 10,000 V/V, packaged in an 8-pin PDIP (P) package. It adds differential input measurement with high input impedance to low-level sensor signals while drawing very little supply current.

An instrumentation amplifier (INA) is a precision differential amplifier optimized for sensing small signals buried in noise and common-mode interference. Structurally it sits above an operational amplifier, which itself sits inside the broader family of analog signal-chain amplifiers. The INA122 uses a two-op-amp architecture with excellent performance and very low quiescent current, so the hierarchy is instrumentation amplifier to difference amplifier to operational amplifier to analog IC, with the INA122 designed for portable instrumentation and data-acquisition systems.

Key specifications include a low quiescent current of 60 uA, a wide power-supply range reaching 36 V on a single supply, a common-mode range of (V-) minus 0.1 V, and a rail-to-rail output swing. Input offset voltage is specified at 250 uV maximum and input offset drift at 3 uV/degC maximum, which keeps gain error and drift low at high gain settings. The device offers 120 kHz bandwidth and 90 dB common-mode rejection, so high-frequency common-mode noise and gain-bandwidth-limited signals are both well controlled.

Technically, the two-op-amp topology gives a gain set entirely by one external resistor connected between the RG pins. That means the gain equation is set by a single component value rather than a matched resistor network, which simplifies calibration and keeps the design robust across temperature. Internal feedback resistors are laser trimmed, so CMRR and offset behavior stay consistent without external trimming.

Typical uses include bridge and load-cell front ends, thermocouple and RTD signal conditioning, battery-powered portable medical monitors, current-shunt measurement in power supplies, and general-purpose low-level data acquisition front ends where both low quiescent current and wide supply range matter.

When designing around the INA122PA, plan the RG resistor network for the lowest gain you can tolerate, place input filtering close to the pins, and note that the input common-mode range sits close to the negative rail, so the signal must remain above (V-) minus 0.1 V. Reference and supply decoupling capacitors should be placed adjacent to pins 5 and 7 for stable operation.

This page consolidates manufacturer specifications, drop-in PDIP-8 alternatives, comparison data and practical design notes into one engineering reference that goes beyond a single datasheet download.

جێگرەوەکانی جێگۆڕکێ بۆ INA122PA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ INA122PA (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Gain Range, Product Type, Quiescent Current, Amplifier Type.

Analog Devices
Package: 8-lead PDIP
Gain Range: 1 to 10,000
Product Type: Low-cost, low-power, high-accuracy instrumentation amplifier
بەراوردکردن لەگەڵ INA122PA →
Analog Devices
Package: 8-pin PDIP (0.300 inch, 7.62 mm pitch)
Product Type: Instrumentation Amplifier
بەراوردکردن لەگەڵ INA122PA →
Analog Devices
Package: 8-SOIC (0.154 in, 3.90 mm width)
Gain Range: 1 to 1000+
Amplifier Type: Instrumentation Amplifier
بەراوردکردن لەگەڵ INA122PA →
Texas Instruments
Gain Range: 1 V/V to 10,000 V/V (single external resistor)
Quiescent Current: ±450 µA typical
Amplifier Type: Instrumentation Amplifier (3-op-amp topology)
بەراوردکردن لەگەڵ INA122PA →
Texas Instruments
Package: 8-pin plastic DIP (8-PDIP)
Product Type: Precision instrumentation amplifier
Quiescent Current: 60 µA
بەراوردکردن لەگەڵ INA122PA →
Texas Instruments
Package: 16-pin PDIP
Gain Range: 4 to 10,000
Product Type: Single-channel instrumentation amplifier with precision voltage reference
بەراوردکردن لەگەڵ INA122PA →

INA122P

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-8 (P)
Precision instrumentation amplifier · Two-op-amp design · 60 µA · 2.2 V to 36 V · ±18 V · V− − 0.1 V · Rail-to-rail · 250 µV maximum

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA121P

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-8 (P)
Instrumentation Amplifier (3-op-amp topology) · 1 · FET / CMOS · ±4 pA typical · ±200 µV typical · ±2 µV/°C typical · 20 nV/√Hz at 1 kHz · ±450 µA typical

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA125PA

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-8 (P)
Single-channel instrumentation amplifier with precision voltage reference · 1 circuit · 4 to 10,000 · Single external resistor · 10 V · 1.35 V to 18 V · 460 µA · 250 µV maximum

پەیوەندی بۆ نرخ

بینینی داتاشیت →

AD620ANZ

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 PDIP-8
Low-cost, low-power, high-accuracy instrumentation amplifier · 1 channel · 1 to 10,000 · One external resistor · 1 MHz · 1.3 mA · 2 nA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

AD621ANZ

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 PDIP-8
Instrumentation Amplifier · 1 circuit · 8-pin PDIP (0.300 inch, 7.62 mm pitch) · Through-hole · Tube · 800 kHz at -3 dB · 1.2 V/µs · 1.3 mA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

INA122PA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Type Instrumentation amplifier, two-op-amp design
Number of Channels 1
Supply Voltage Range (Single Supply) 2.2 V to 36 V
Supply Voltage Range (Dual Supply) +/-18 V
ئێستای ئارام 60 uA
Input Offset Voltage (max) 250 uV
Input Offset Drift (max) 3 uV/degC
Common-Mode Rejection Ratio 90 dB
Gain Range 5 V/V to 10,000 V/V
Gain Bandwidth Product 120 kHz
Input Common-Mode Range (V-) - 0.1 V
Output Swing Rail-to-rail
پاکێج 8-pin PDIP (P)
جۆری دامەزراندن Through-hole
Supply Type Single or dual supply operation

ڕێکخستنی پینی INA122PA

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پین 1 RG — Gain set resistor connection
پین 2 IN- — Inverting input
پین 3 IN+ — Non-inverting input
پین 4 V- — Negative supply connection
پین 5 REF — Reference input for output offsetting
پین 6 OUT — Output voltage
پین 7 V+ — Positive supply connection
پین 8 RG — Gain set resistor connection

بەکارهێنانە باوەکان

INA122PA گونجاوە بۆ 6 بەکارھێنانs: Portable Medical Monitor Front End, Load Cell and Bridge Sensor Signal Conditioning, Thermocouple and RTD Signal Conditioning, Battery-Powered Data Acquisition Module, Power Supply Current and Shunt Measurement, Precision Analog Signal Conditioning for Test Equipment.

💊

Portable Medical Monitor Front End

The INA122PA suits portable medical monitoring because its 60 uA quiescent current and 2.2 V to 36 V single-supply capability let the amplifier run continuously from a small cell while monitoring weak bio-sensor signals. Its 250 uV maximum offset voltage and 3 uV/degC maximum drift keep baseline wander out of the measurement path, while the 90 dB CMRR rejects the mains-coupled interference common in hospital and wearable environments. Place the device directly at the electrode or sensor input, set gain with the single RG resistor, and use the REF pin to bias the output into the input range of the following converter. The rail-to-rail output swing helps when the ADC reference is low and headroom is tight.

🏭

Load Cell and Bridge Sensor Signal Conditioning

A Wheatstone bridge produces a small differential millivolt signal riding on a large common-mode voltage, which is exactly the signal class the INA122PA is designed to amplify. The (V-) minus 0.1 V input common-mode range and 90 dB CMRR reject the supply-bump component of that common-mode voltage, and the single external RG resistor lets you set gain from 5 V/V up to 10,000 V/V to bring the full-scale bridge output into the converter input range. The 120 kHz bandwidth is ample for quasi-static load measurement while still covering mechanical resonances for dynamic weighing. Use the REF pin for output offsetting when your converter lacks an internal reference.

🌐

Thermocouple and RTD Signal Conditioning

Thermocouple outputs are only tens of microvolts per degree, so offset voltage and drift dominate the error budget, and the INA122PA's 250 uV maximum offset plus 3 uV/degC maximum drift keep the measurement stable over industrial temperature ranges. The wide 2.2 V to 36 V supply range lets the same part sit behind a 24 V industrial loop supply without level shifting, and the low 60 uA quiescent current suits panel-mounted transmitters. Differential input also rejects the AC mains pickup that appears on unshielded thermocouple wiring. Configure the gain resistor for the sensor's sensitivity, then feed the output into a low-drift converter and use the REF pin for cold-junction compensation offset.

🧩

Battery-Powered Data Acquisition Module

A compact data acquisition module that must run for weeks on a single battery benefits directly from the INA122PA's 60 uA quiescent current, which lets the amplifier remain enabled continuously instead of being duty-cycled. At a 3 V supply the internal dissipation is negligible, and the 2.2 V minimum operating supply lets the module run from a single Li-ion cell without a boost stage. The 120 kHz bandwidth covers most industrial analog channels such as pressure, position and vibration envelopes, and the rail-to-rail output swing maximizes the usable span of a low-voltage ADC. Pair the amplifier with a low-power ADC and keep the RG resistor footprint free for field gain re-ranging.

⚡

Power Supply Current and Shunt Measurement

Measuring shunt drop voltage in a high-side or low-side current path demands high common-mode rejection and low offset, and the INA122PA provides 90 dB CMRR with 250 uV maximum offset in a low-power package. At a 60 uA quiescent current the amplifier adds negligible parasitic load to the monitored rail, which matters when measuring microamp-scale standby currents in a system. The 36 V maximum single-supply rating lets the amplifier sit directly on a 12 V or 24 V telemetry rail without a separate level shifter. Use a shunt that keeps the differential drop within the amplifier's common-mode range, and reference the output to ground through the REF pin when the converter expects a unipolar signal.

🔧

Precision Analog Signal Conditioning for Test Equipment

In bench and portable test equipment, the INA122PA conditions low-level differential inputs ahead of a converter while keeping the power budget low enough for a handheld instrument. The 5 V/V to 10,000 V/V gain range covers everything from millivolt sensor signals to mid-level instrumentation outputs, and because the gain depends on a single resistor, each input range can be reconfigured with a switch and a resistor network without redesigning the analog section. The 120 kHz bandwidth supports audio-band and low-frequency dynamic measurement, and the low 60 uA quiescent current extends battery life during long test campaigns. The REF pin provides the offsetting needed to drive a single-supply converter from a bipolar sensor.

What is the INA122PA?
The INA122PA is a single-channel, two-op-amp instrumentation amplifier from Texas Instruments with 60 uA quiescent current, a 2.2 V to 36 V single-supply range (or +/-18 V dual supply), programmable gain from 5 V/V to 10,000 V/V and a 120 kHz gain-bandwidth product, housed in an 8-pin PDIP package. According to the Texas Instruments INA122 datasheet, it is intended for portable instrumentation and data-acquisition systems where low supply current and wide supply range are both required.
What is the supply voltage range of the INA122PA?
The INA122PA operates from 2.2 V to 36 V on a single supply and from plus/minus 18 V on a dual supply. The Texas Instruments INA122 datasheet lists a wide power supply range of single supply up to 36 V and dual supply of +/-18 V, and the device can be operated with either configuration. The rail-to-rail output swing means the output can approach the supply rails, which is useful in low-voltage single-supply systems where headroom is limited.
What is the quiescent current of the INA122PA?
The INA122PA draws only 60 uA of quiescent current. The Texas Instruments INA122 datasheet highlights a low quiescent current of 60 uA as the headline feature of the family, which is what makes the amplifier suitable for battery-powered and portable medical instrumentation. At 3 V supply this corresponds to roughly 180 uW of internal dissipation, so a battery-powered front end can keep the amplifier always on without dominating the standby budget.
What are the offset voltage and offset drift of the INA122PA?
The INA122PA has a maximum input offset voltage of 250 uV and a maximum input offset drift of 3 uV/degC. The Texas Instruments INA122 datasheet lists these as precision specifications alongside the 90 dB common-mode rejection ratio. At a gain of 1000, a 250 uV offset translates to a 250 mV output error, so offset and drift should be included in your error budget whenever the gain setting is high.
How do I set the gain of the INA122PA?
The INA122PA gain is set by a single external resistor connected between the RG pins (pins 1 and 8), giving a range of 5 V/V to 10,000 V/V. The two-op-amp architecture described in the Texas Instruments INA122 datasheet means only one resistor value must be chosen, and the internal feedback resistors are laser trimmed for consistent common-mode rejection. Lower gain settings provide higher bandwidth, so choose the lowest gain that still provides the required resolution.
What is the INA122PA pinout?
The INA122PA is an 8-pin PDIP with pin 1 RG (gain resistor), pin 2 IN- (inverting input), pin 3 IN+ (non-inverting input), pin 4 V- (negative supply), pin 5 REF (reference), pin 6 OUT (output), pin 7 V+ (positive supply) and pin 8 RG (gain resistor). Texas Instruments lists the INA122PA as an 8-pin PDIP (P) package with 8 pins on its product page. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks and net names.
Where to download the INA122PA datasheet PDF?
The official INA122PA datasheet PDF is hosted by Texas Instruments at https://www.ti.com/lit/ds/symlink/ina122.pdf, and the product landing page at https://www.ti.com/product/INA122 carries the same data plus parametric search and package options. The document is titled Single Supply, Micropower Instrumentation Amplifier and covers features, electrical characteristics, pin configurations and typical application circuits for the whole INA122 family.
Where can I buy the INA122PA online?
The INA122PA is available as a standard orderable catalog part in the 8-pin PDIP package. Use the Request a Quote form on this page to obtain current availability, minimum order quantity, lead time and delivered pricing for the INA122PA, and to have a purchase order prepared against the exact manufacturer part number and packaging you require.
What is the lead time for the INA122PA?
Lead time for the INA122PA depends on the packaging option and current factory loading, and it changes over time. The manufacturer lists INA122PA as an active catalog part in the PDIP (P) package, so it is a normal production item rather than a legacy or no-longer-ordered device. Request the current lead time and stock position through the Request a Quote form on this page so the answer reflects today's inventory rather than a static listing.
Is the INA122PA in stock?
Stock for the INA122PA fluctuates with distributor inventory and factory output, so a real-time check is the only reliable answer. Texas Instruments lists the INA122PA as an active part in the PDIP-8 package. Submit a Request a Quote on this page for a current stock and delivery confirmation for the exact quantity and package you need.
What is the difference between INA122PA and INA122UA?
The INA122PA and INA122UA are the same INA122 silicon in different packages: INA122PA is the 8-pin PDIP (through-hole) version, while INA122UA is the 8-pin SOIC (surface-mount) version. Both carry the same 60 uA quiescent current, 2.2 V to 36 V supply range, 250 uV maximum offset and 5 V/V to 10,000 V/V gain range, but the land patterns are different, so they are not drop-in replacements for each other on the same PCB.
INA122PA vs AD620ANZ - which is better for a bridge sensor front end?
For a bridge sensor front end, the INA122PA is preferable when low power and a wide single-supply range dominate, while the AD620ANZ offers lower offset voltage and lower drift. The INA122PA is specified at 60 uA quiescent current, 250 uV maximum offset and 3 uV/degC maximum drift, versus the AD620 family's 75 uV typical offset and lower drift ratings. Both are 8-pin PDIP parts with a common instrumentation-amplifier pinout, so footprint compatibility is not the deciding factor.
When should I choose the INA122PA over the AD620ANZ?
Choose the INA122PA when your design is battery powered or powered from a low single supply that can reach 36 V, when supply headroom for the output swing is limited, or when 60 uA quiescent current dominates your power budget. Choose the AD620ANZ when your accuracy budget requires lower offset voltage and drift at high gain, or when you already have an AD620 design in production. The INA122PA also offers 90 dB CMRR and 120 kHz bandwidth for signals above DC.
Is the INA122PA suitable for battery-powered medical instrumentation?
Yes, the INA122PA is well suited to battery-powered medical and portable instrumentation. Texas Instruments describes the INA122 as a low-power instrumentation amplifier ideal for portable medical and data acquisition applications, and the family's headline feature is the 60 uA quiescent current. Combined with the 2.2 V minimum single-supply operation and the wide common-mode range reaching (V-) minus 0.1 V, it supports low-level sensor front ends where every milliamp of supply current matters.
What is the best drop-in replacement for the INA122PA?
The best same-package drop-in replacements for the INA122PA are the INA122P (the same 8-pin PDIP orderable variant), the INA125PA and the INA121P, all from the same Texas Instruments instrumentation-amplifier family and all in the PDIP-8 package with a matching RG/IN+/IN-/V-/REF/OUT/V+ pin arrangement. For a cross-brand option in the same PDIP-8 footprint, the Analog Devices AD620ANZ and AD621ANZ are commonly used. Verify gain-bandwidth and common-mode-range differences against your signal before swapping.
Can the INA121P replace the INA122PA?
Yes, the INA121P can serve as a drop-in replacement for the INA122PA when your circuit stays inside the INA121's electrical limits. Both are Texas Instruments 8-pin PDIP instrumentation amplifiers with the same RG, IN+, IN-, V-, REF, OUT and V+ pin arrangement and the same 5 V/V to 10,000 V/V gain range, but the INA121 offers a higher gain-bandwidth product for faster signals. Verify supply range, offset and common-mode range for your specific design before the swap.
What is the best Analog Devices equivalent for the INA122PA?
The closest Analog Devices equivalent in the same 8-pin PDIP footprint is the AD620ANZ, a classic single-gain-set instrumentation amplifier with a 1 V/V to 10,000 V/V gain range, a wide supply range and the standard RG/IN+/IN-/V-/REF/OUT/V+ pinout. The AD621ANZ is the offset-optimized sibling in the same package. Neither matches the INA122PA's 60 uA quiescent current figure exactly, so confirm supply current and offset against your error and power budgets.
What are the key specifications of the INA122PA that engineers should know?
The INA122PA combines a 60 uA quiescent current, a 2.2 V to 36 V single-supply or +/-18 V dual-supply range, 250 uV maximum input offset voltage, 3 uV/degC maximum offset drift, 90 dB CMRR, 120 kHz bandwidth, a (V-) minus 0.1 V common-mode range and rail-to-rail output swing, with gain set from 5 V/V to 10,000 V/V by one external resistor in an 8-pin PDIP package. These are the figures quoted in the Texas Instruments INA122 datasheet feature list and electrical characteristics tables.
What can replace an INA122PA?
Practical replacements for the INA122PA fall into two groups: same-package Texas Instruments parts such as the INA122P, INA125PA and INA121P, and cross-brand 8-pin PDIP instrumentation amplifiers such as the AD620ANZ and AD621ANZ from Analog Devices. All of them keep the standard instrumentation-amplifier pinout with RG on pins 1 and 8 and reference on pin 5, so the PCB needs no change. The trade-offs sit in gain-bandwidth product, offset voltage, drift and quiescent current, which must be checked against your design limits.

داتای سەرچاوەی ئەندازیاری بۆ INA122PA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the INA122PA when your front end is battery powered, powered from a single supply that can sit well above 5 V, or when you need an instrumentation amplifier with roughly 60 uA quiescent current and a common-mode range reaching (V-) minus 0.1 V. It is the natural choice for portable medical monitors, bridge sensors and low-level data acquisition where the 250 uV maximum offset and 3 uV/degC drift still meet the error budget. Pick the INA122P if you want a second sourcing channel for the identical silicon in the same PDIP-8 footprint, and pick the INA121P when your signal bandwidth needs exceed 120 kHz. Pick the INA125PA when you need a rail-to-rail input stage and unity gain is acceptable. Pick the AD620ANZ or AD621ANZ from Analog Devices when offset voltage and drift are the dominant error terms and you can accept higher supply current. All listed alternatives share the 8-pin PDIP footprint and the standard RG/IN+/IN-/V-/REF/OUT/V+ pinout, so no board change is required.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە INA122P INA121P INA125PA AD620ANZ AD621ANZ
Package 8-pin PDIP (P) 8-pin PDIP (P) - same 8-pin PDIP - same 8-pin PDIP - same 8-pin PDIP - same 8-pin PDIP - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Analog Devices Analog Devices
Gain Range 5 V/V to 10,000 V/V 5 V/V to 10,000 V/V 5 V/V to 10,000 V/V 1 V/V to 10,000 V/V 1 V/V to 10,000 V/V 1 V/V to 10,000 V/V

جیاکەرەوە سەرەکییەکان

  • Exceptionally low quiescent current for a gain-programmable instrumentation amplifier (بەراورد بەAD620ANZ)
  • Wider single-supply operating ceiling than classic precision instrumentation amplifiers (بەراورد بەINA121P)
  • Single external resistor sets gain across a wide 5 to 10,000 V/V range (بەراورد بەINA125PA)
  • Same-package identical-cost sourcing within the family (بەراورد بەINA122P)

تێبینییەکانی دیزاین

The INA122 input common-mode range extends only to (V-) minus 0.1 V, so a bipolar sensor output that swings below the negative rail will clip the input stage even though the output stage is rail-to-rail. Either bias the sensor output into the valid range, add a level shift ahead of the amplifier, or run on a dual supply where the signal sits mid-rail. Also note that the minimum gain of the INA122 is 5 V/V, so designs that need unity gain must add an external amplifier stage after pin 6.

The gain resistor connects between pins 1 and 8, so keep that loop physically short and away from the input and output traces to minimize parasitic pickup that unbalances the differential pair. Route IN+ and IN+ as a tight, closely spaced pair from the sensor to pins 2 and 3, and place a differential input filter (matched RC) directly at the pins if cable pickup is expected. Place supply decoupling capacitors adjacent to pins 4 and 7, and tie REF (pin 5) to a clean ground or reference node with a short, low-impedance trace.

Estimated: the INA122 quiescent current of 60 uA at a 3 V single supply is 180 uW of internal dissipation, which is negligible, so the dominant supply cost in a portable design is the load current plus the converter's own efficiency at light load. The real thermal consideration appears at high gain with a large input signal, where output drive current and internal power grow; keep the gain resistor value moderate and avoid long-term saturation of the output stage, since a saturated amplifier dissipates the full supply rail across the output stage.

Because the two-op-amp architecture relies on matching internal feedback resistors, input bias current and impedance differences can degrade CMRR at high frequencies. Use high-impedance, low-leakage sensors and keep source impedances balanced on pins 2 and 3; mismatched source resistance directly converts bias current difference into offset error. For gain settings above roughly 1000 V/V, verify offset and drift in the system error budget, since 250 uV of input offset becomes 250 mV at the output.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The INA122PA is a Texas Instruments catalog part in the PDIP-8 (P) package, but no RoHS, REACH, lead-free or conflict-minerals declarations are stated in the available manufacturer material. Automotive qualification is not claimed for this part; it is a general-purpose instrumentation amplifier.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ina122pa datasheet INA122PA INA122PA pinout INA122PA datasheet pdf INA122PA 8-PDIP INA122PA price INA122PA stock Texas Instruments INA122PA INA122PA vs AD620ANZ INA122PA drop-in replacement INA122 instrumentation amplifier 60uA INA122PA bridge sensor amplifier INA122PA gain resistor calculation INA122PA equivalent PDIP-8

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments INA122 INA122PA INA122P INA121P INA125PA AD620ANZ AD621ANZ Analog Devices instrumentation amplifier difference amplifier operational amplifier analog signal chain amplifier quiescent current common-mode rejection ratio (CMRR) input offset voltage input offset drift gain set resistor rail-to-rail output PDIP-8 DIP package family through-hole surface mount low-level transducer signal conditioning load cell amplifier data acquisition system
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ