INA134PA - 0dB Audio Differential Receiver | Texas Instruments
MPN: INA134PA ✓ چالاکINA134PA گشتی
An audio differential line receiver is a specialized amplifier that accepts a balanced or unbalanced audio signal, rejects common-mode noise, and produces a single-ended output. The INA134 belongs to the broader amplifier IC hierarchy and is intended for professional and high-fidelity audio paths where low distortion, adequate slew rate, common-mode rejection, and output drive are more important than a small package or minimal power consumption.
Key features include a 90dB common-mode rejection ratio, fixed unity gain, 0.0005% distortion at 1kHz, and a 14V/µs slew rate. The wide output-voltage swing and high output-drive capability allow the receiver to drive downstream circuitry without adding substantial distortion. A maximum quiescent current of 2.9mA also supports straightforward analog power-supply design where adequate headroom and grounding remain important.
Internally, the INA134 combines high-performance operational amplifiers with on-chip precision resistors. The integrated resistor network establishes the fixed 1V/V gain and helps control gain-related errors without requiring an external matched resistor set. Its differential architecture is intended to suppress signal-correlated noise and interference that appears equally on both input lines.
Typical uses include balanced professional audio inputs, stereo differential line receivers, mixer input stages, audio interface front ends, and instrumentation that receives low-level differential signals. The INA134PA is particularly appropriate when an through-hole package is preferred and a ±15V or ±18V analog supply is available.
The primary design consideration is ensuring adequate supply headroom for signal peaks and output swing. Input and return paths should be routed as a balanced pair, with attention to grounding and source impedance. Decoupling close to the supply pins and short, symmetric signal traces help preserve the receiver’s low-noise and high-rejection performance.
This page combines verified manufacturer specifications, distributor availability information, lifecycle guidance, and an engineering-oriented comparison of the INA134PA with relevant alternatives. It also identifies where verified drop-in data is limited so engineers can distinguish confirmed compatibility from generic or cross-package substitutions.
جێگرەوەکانی جێگۆڕکێ بۆ INA134PA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ INA134PA (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Slew Rate.
INA134PAG4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
INA134PA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Single audio differential line receiver |
| Gain | 1V/V (0dB) |
| Differential Distortion | 0.0005% at 1kHz |
| Slew Rate | 14V/µs |
| Common-Mode Rejection Ratio | 90dB |
| Supply Range | ±18V |
| ئێستای ئارام | 2.9mA maximum |
| Settling Time | 0.01% settling time specification; timing value not provided |
| Number of Channels | 1 channel |
| پاکێج | 8-pin PDIP (P) |
| ژمارەی پین | 8 pins |
| جۆری دامەزراندن | Through-hole |
| مەودای پلەی گەرمیی کارکردن | -40°C to +85°C |
| Integrated Components | High-performance operational amplifiers with on-chip precision resistors |
| Output Drive | High output drive capability; current value not provided |
| Output Voltage Swing | Wide output voltage swing; numeric limits not provided |
ڕێنمایی ڕێکخستنی پینی INA134PA 8-pin pdip (p)
ڕێکخستنی پین بۆ INA134PA (پاکێجی 8-pin pdip (p)). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ INA134PA.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
INA134PA گونجاوە بۆ 6 بەکارھێنانs: Balanced Professional Audio Input, Stereo Mixer Input Stage, Audio Interface Front End, Low-Level Differential Instrumentation, Consumer Audio Differential Input, Audio Monitoring and Test Equipment.
Balanced Professional Audio Input
The INA134PA fits a balanced professional-audio input because its 1V/V gain preserves the received signal level while the 90dB CMRR suppresses noise common to both conductors. Place the receiver at the connector or preamplifier input and route the pair as a differential signal to preserve common-mode rejection. Its 0.0005% distortion at 1kHz and 14V/µs slew rate support low-distortion signal transfer, provided the ±18V-capable supply has adequate headroom and the source impedance remains within the device’s expected operating conditions.
پێشنیارکراو
Stereo Mixer Input Stage
For a stereo mixer, one INA134PA can receive each balanced channel without adding voltage gain, allowing the following stage to establish channel level and fader behavior. The receiver’s 90dB CMRR is useful when cable pickup appears equally on both input legs, while the 14V/µs slew rate preserves dynamic response across rapidly changing musical transients. Keep the two inputs symmetric, avoid long unprotected input runs, and verify the mixer’s expected source impedance and supply compatibility before insertion.
پێشنیارکراو
Audio Interface Front End
The INA134PA can serve as the analog receiving stage ahead of a professional audio interface that expects a unity-gain differential signal. Its 0.0005% distortion at 1kHz and 90dB CMRR reduce errors introduced before conversion, while the 1V/V gain preserves the source amplitude for later mixer and converter stages. Place supply decoupling close to the device, route the balanced pair together, and confirm that the downstream converter accepts the output swing and common-mode range produced by the receiver.
پێشنیارکراو
Low-Level Differential Instrumentation
INA134PA is applicable when a low-level differential measurement must be converted to a single-ended signal with minimal gain adjustment. Although its primary specifications target audio, the 90dB CMRR helps reject shared interference, and the 14V/µs slew rate supports fast signal changes. Because this is a unity-gain audio receiver rather than a general-purpose instrumentation amplifier, the designer should verify input range, offset, bias current, output swing, and stability against the actual source before production use.
پێشنیارکراو
Consumer Audio Differential Input
The INA134PA can be used in consumer audio equipment that receives balanced sources but requires a single-ended internal signal. Its fixed 1V/V gain keeps the signal path straightforward, and the 0.0005% distortion at 1kHz is suitable for high-quality audio amplification. The through-hole PDIP-8 package also simplifies repair and retrofit work in existing equipment. Designers should still account for the positive and negative supply requirements and ensure that connector, ground, and cable geometry support the rejection performance claimed for differential operation.
پێشنیارکراو
Audio Monitoring and Test Equipment
INA134PA can form the input receiver in monitoring equipment, test instruments, and signal-conversion systems that need a low-distortion unity-gain path. The 14V/µs slew rate supports sharply changing test waveforms, while 90dB CMRR can improve measurement integrity when a differential source introduces common-mode noise. For accurate results, terminate the source correctly, maintain symmetric input routing, provide stable positive and negative supplies, and calibrate downstream gain because INA134PA itself intentionally provides only 1V/V voltage gain.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ INA134PA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | INA134PAG4 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP (P) | 8-pin PDIP (P) |
| Function | Audio differential line receiver | Audio differential line receiver |
| Gain | 1V/V (0dB) | 1V/V (0dB) |
| Distortion | 0.0005% at 1kHz | 0.0005% at 1kHz |
| Slew Rate | 14V/µs | 14V/µs |
| Common-Mode Rejection Ratio | 90dB | 90dB |
| Maximum Quiescent Current | 2.9mA | 2.9mA |
| Supply Range | ±18V | ±18V |
جیاکەرەوە سەرەکییەکان
- Low-distortion unity-gain audio receiving (بەراورد بەINA134PAG4)
- Common-mode interference rejection (بەراورد بەINA134PAG4)
- Through-hole continuity for legacy audio designs (بەراورد بەINA134UA)
تێبینییەکانی دیزاین
Route the INA134PA differential input pair together with matched geometry and similar impedances. Minimize loop area between the source, receiver, and return path because differential rejection depends on the unwanted noise remaining common-mode. Keep input traces away from switching nodes and high-current return paths, and avoid sharing a long ground trace between the input return and unrelated output stages.
Provide local supply bypassing at the INA134PA and preserve adequate headroom on positive and negative rails for the maximum input and output excursion. The verified device specification allows a ±18V supply range and limits quiescent current to 2.9mA maximum, but it does not provide the detailed output-swing limits needed for layout calculations. Consult the full manufacturer datasheet before sizing headroom or asserting a specific peak output level.
Do not treat a generic cross-reference result as proof of drop-in compatibility. The verified data confirms an 8-pin PDIP format for INA134PA and identifies INA134PAG4 as a closely related same-package candidate. INA134UA is described as a surface-mount equivalent and would require a PCB change; any different gain family, such as INA2134, is not a parameter-equivalent replacement for a unity-gain circuit.
زانیاری پابەندبوون
The supplied verified excerpts identify the manufacturer, family functions, electrical characteristics, package, and temperature range but do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.