INA148UA/2K5 - ±200V Difference Amplifier | Texas Instruments
MPN: INA148UA/2K5 ✓ چالاکINA148UA/2K5 گشتی
A difference amplifier is an amplifier category that subtracts two input voltages and scales the result. The INA148 combines a monolithic precision bipolar operational amplifier with a laser-trimmed thin-film resistor network. This integrated network establishes an accurate 1 V/V gain, accurate common-mode rejection, and stable tracking over temperature without requiring external matched resistors.
The principal electrical features include ±200 V common-mode capability, unity gain, 100 kHz gain-bandwidth product, 86 dB common-mode rejection at 100 kHz, 1 mV typical input offset voltage, 10 µV/°C typical input offset drift, 1 V/µs slew rate, and 880 nV/√Hz input noise at 1 kHz. The laser-trimmed network improves gain accuracy and common-mode rejection by reducing resistor mismatch.
The INA148 is intended for high-side and low-side current sensing, bridge and shunt measurements, industrial process-control signals, and test equipment where a small differential voltage must be extracted from a large common-mode voltage. Its bipolar input stage supports single or dual supply operation, while the low-power architecture is suited to compact signal-conditioning modules.
Typical implementation requires careful attention to input protection, supply bypassing, and the REF pin. The REF pin allows output offset adjustment when the application cannot tolerate the small internal offset voltage. Input-referenced protection networks must withstand the applicable ±200 V common-mode environment while preserving the amplifier’s accuracy.
Use short, direct input traces and place supply-decoupling capacitors close to the power pins to preserve high-frequency behavior. Because this is a precision measurement amplifier rather than a power device, thermal management centers on maintaining stable copper and ground paths. The INA148UA/2K5 provides a practical combination of wide common-mode range, unity gain, and compact packaging for instrumentation-grade signal conditioning.
This page brings together the verified device characteristics, commercially relevant sourcing information, same-footprint alternatives, and application-focused design guidance to support component selection and PCB implementation.
جێگرەوەکانی جێگۆڕکێ بۆ INA148UA/2K5 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ INA148UA/2K5 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Operating Temperature Range, Product Type, Supply Voltage Range, Amplifier Type.
INA148UA/2K5G4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
INA143U
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →INA146UAG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →INA149AIDR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →INA141U/2K5G4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
INA148UA/2K5 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Precision unity-gain difference amplifier |
| Common-Mode Input Voltage Range | ±200 V |
| Differential Gain | 1 V/V |
| Supply Voltage Range | 2.7 V to 36 V total |
| Typical Single-Supply Range | 1.35 V to 18 V |
| Typical Dual-Supply Range | ±1.35 V to ±18 V |
| Gain-Bandwidth Product | 100 kHz |
| Common-Mode Rejection | 86 dB at 100 kHz |
| Input Offset Voltage | 1 mV typical |
| Input Offset Voltage Drift | 10 µV/°C typical |
| Slew Rate | 1 V/µs |
| Input Noise Density | 880 nV/√Hz at 1 kHz |
| Input Bias Current | 260 µA typical |
| Quiescent Supply Current | 13 mA typical |
| Settling Time | 25 µs |
| مەودای پلەی گەرمیی کارکردن | -55 °C to +125 °C |
| پاکێج | 8-pin SOIC (D) |
| جۆری دامەزراندن | Surface mount |
| دۆخی RoHS | Compliant |
| Output Reference Control | REF pin for output offset adjustment |
| Protection Features | Current limiting and short-circuit protection |
| Amplifier Architecture | Monolithic precision bipolar operational amplifier with laser-trimmed thin-film resistor network |
| جۆری دەرچوون | Rail-to-rail output |
ڕێکخستنی پینی INA148UA/2K5
| پین 1 | RG — Gain resistor connection |
| پین 2 | IN- — Inverting input |
| پین 3 | IN+ — Noninverting input |
| پین 4 | V- — Negative supply |
| پین 5 | REF — Reference input for output offset adjustment |
| پین 6 | OUT — Output |
| پین 7 | V+ — Positive supply |
| پین 8 | RG — Gain resistor connection |
بەکارهێنانە باوەکان
INA148UA/2K5 گونجاوە بۆ 6 بەکارھێنانs: High-Side Shunt Current Sensing, Motor Drive and Power-Bus Measurement, Industrial Bridge and Sensor Interface, Battery-Pack and DC-Link Monitoring, Power-Lab and Test Equipment, Audio and Communication Equipment.
High-Side Shunt Current Sensing
The INA148UA/2K5 fits high-side shunt sensing when the shunt sits at a voltage that can vary across ±200 V. Its fixed 1 V/V gain directly reproduces the shunt voltage, while 86 dB common-mode rejection at 100 kHz reduces the effect of switching and capacitive common-mode noise. Place protection components close to IN+ and IN− and keep their connections symmetrical. The principal design trade-off is that the amplifier itself cannot survive voltages beyond its specified common-mode range, so external attenuation, clamping, or isolation may be required in harsh automotive or industrial environments.
پێشنیارکراو
Motor Drive and Power-Bus Measurement
The INA148UA/2K5 is appropriate for sensing small voltage differences on high-voltage motor-drive buses where the common-mode signal may approach ±200 V. Its ±200 V range separates measurement from the bus voltage, and the 100 kHz gain-bandwidth product is sufficient for slower feedback, monitoring, and protection channels. The 1 V/µs slew rate also preserves large-signal response. Designers should use Kelvin routing at the shunt, separate the input network from power-switching traces, and confirm that transients do not exceed the absolute maximum ratings.
پێشنیارکراو
Industrial Bridge and Sensor Interface
The INA148UA/2K5 can condition a low-level differential bridge output while rejecting large plant-generated common-mode voltage. Its laser-trimmed thin-film resistor network gives a nominal 1 V/V gain without external matched resistor networks, which simplifies instrumentation layouts. The 1 mV typical offset and 10 µV/°C typical drift are important when resolving small bridge signals. Place the amplifier close to the bridge connector, provide local supply bypassing, and use symmetric input traces so that resistance and thermal gradients do not degrade differential accuracy.
پێشنیارکراو
Battery-Pack and DC-Link Monitoring
The INA148UA/2K5 supports battery-management systems that need to measure a small differential voltage across a shunt or sensing element referenced to a high battery voltage. Its common-mode capability permits measurements across a ±200 V operating range, while unity gain avoids external gain-setting components. The device must operate from a separate low-voltage supply, so its V+ and V− pins should be decoupled independently from the high-energy battery path. Designers must add input limiting appropriate to the battery chemistry and verify temperature performance across the required ambient range.
پێشنیارکراو
Power-Lab and Test Equipment
The INA148UA/2K5 is useful in programmable power and test equipment for observing a small differential voltage superimposed on a high common-mode output. Its fixed 1 V/V gain makes calibration straightforward, and its 25 µs settling time supports measurement systems operating outside the highest audio and communications bands. The REF pin can introduce a deliberate output offset for calibration or level shifting. For bench instruments, connect the REF pin appropriately, provide clean low-noise supply rails, and place input and output filtering where it will not introduce unmatched capacitance.
پێشنیارکراو
Audio and Communication Equipment
The INA148UA/2K5 can monitor differential outputs in professional audio, communications, and line-interface circuits when a large common-mode voltage is present. Its 880 nV/√Hz input noise at 1 kHz and 100 kHz bandwidth make it useful for low-level monitoring rather than the highest-bandwidth audio paths. The unity-gain topology preserves signal polarity and simplifies channel matching. Maintain symmetric input routing, use low-value protection resistors, and keep the output load within the device’s rated drive capability to avoid degrading offset and distortion performance.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ INA148UA/2K5 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | INA148UA/2K5G4 | INA143U | INA146UAG4 | INA149AIDR | INA141U/2K5G4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-8 (D) | SOIC-8 (D) - same | SOIC-8 (D) - same | SOIC-8 (D) - same | SOIC-8 (D) - same | SOIC-8 (D) - same |
| Common-Mode Voltage Range | ±200 V | ±200 V | ±275 V | ±350 V | ±350 V | ±275 V |
| Differential Gain | 1 V/V | 1 V/V | 1 V/V | 1 V/V | 1 V/V | 1 V/V |
جیاکەرەوە سەرەکییەکان
- Direct same-family ordering alternative (بەراورد بەINA148UA/2K5G4)
- Closer common-mode operating point than higher-voltage families (بەراورد بەINA149AIDR)
- Integrated precision resistor network (بەراورد بەINA143U)
- Documented wide temperature capability (بەراورد بەINA141U/2K5G4)
تێبینییەکانی دیزاین
Do not treat the ±200 V common-mode rating as permission to place unprotected inputs directly on an uncontrolled high-voltage bus. Use appropriately rated series resistors, clamps, or isolation as required by the installation and applicable safety requirements. Check both the steady-state common-mode voltage and the maximum transient because a narrow switching spike can exceed a nominal operating range even when the average bus voltage remains within ±200 V.
Route IN+ and IN− as a closely matched differential pair from the sensing point to the SOIC inputs. Avoid sharing return-current paths with power-switching nodes, keep the input traces away from inductors and switching nodes, and use identical protection networks on both inputs. This minimizes converted differential error and preserves the benefit of the integrated 86 dB common-mode rejection.
Place the supply-decoupling capacitor immediately between pins 4 and 7 and connect it with a short, low-inductance ground return. The INA148UA/2K5 operates from single or dual supplies, but the appropriate connection depends on whether REF is grounded or driven. Use the manufacturer reference circuit and pin-description table when establishing the supply and reference configuration.
Account for the 100 kHz gain-bandwidth product when filtering or amplifying rapidly changing differential signals. Additional input capacitance can alter stability or response, and a protection network that is symmetrical at DC may not remain symmetrical over frequency. Validate the complete source impedance, protection components, and output loading with the amplifier’s typical-application configuration.
زانیاری پابەندبوون
RoHS compliance is identified for the INA148UA/2K5. No explicit REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified.