Texas Instruments

INA148UA/2K5 - ±200V Difference Amplifier | Texas Instruments

MPN: INA148UA/2K5 ✓ פעיל
±200 V Vdss 260 µA typical Id 8-pin SOIC (D) Package
כמות הזמנה מינימלית: 1 |

INA148UA/2K5 סקירה

The Texas Instruments INA148UA/2K5 is a precision, unity-gain difference amplifier with a ±200 V common-mode input range, 1 V/V differential gain, and an 8-pin SOIC (D) package. It operates from single or dual supplies with a total supply range up to 36 V, making it suitable for measuring small differential signals embedded in high-voltage industrial and instrumentation systems.

A difference amplifier is an amplifier category that subtracts two input voltages and scales the result. The INA148 combines a monolithic precision bipolar operational amplifier with a laser-trimmed thin-film resistor network. This integrated network establishes an accurate 1 V/V gain, accurate common-mode rejection, and stable tracking over temperature without requiring external matched resistors.

The principal electrical features include ±200 V common-mode capability, unity gain, 100 kHz gain-bandwidth product, 86 dB common-mode rejection at 100 kHz, 1 mV typical input offset voltage, 10 µV/°C typical input offset drift, 1 V/µs slew rate, and 880 nV/√Hz input noise at 1 kHz. The laser-trimmed network improves gain accuracy and common-mode rejection by reducing resistor mismatch.

The INA148 is intended for high-side and low-side current sensing, bridge and shunt measurements, industrial process-control signals, and test equipment where a small differential voltage must be extracted from a large common-mode voltage. Its bipolar input stage supports single or dual supply operation, while the low-power architecture is suited to compact signal-conditioning modules.

Typical implementation requires careful attention to input protection, supply bypassing, and the REF pin. The REF pin allows output offset adjustment when the application cannot tolerate the small internal offset voltage. Input-referenced protection networks must withstand the applicable ±200 V common-mode environment while preserving the amplifier’s accuracy.

Use short, direct input traces and place supply-decoupling capacitors close to the power pins to preserve high-frequency behavior. Because this is a precision measurement amplifier rather than a power device, thermal management centers on maintaining stable copper and ground paths. The INA148UA/2K5 provides a practical combination of wide common-mode range, unity gain, and compact packaging for instrumentation-grade signal conditioning.

This page brings together the verified device characteristics, commercially relevant sourcing information, same-footprint alternatives, and application-focused design guidance to support component selection and PCB implementation.

חלופות תחליף ישיר עבור INA148UA/2K5 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם INA148UA/2K5 (אותו גורם צורה וטביעת רגל) — שונים ב Package, Operating Temperature Range, Product Type, Supply Voltage Range, Amplifier Type.

Texas Instruments
Package: 8-SOIC, 0.154 in width, 3.90 mm width
Operating Temperature Range: -40 C to 85 C
Product Type: Precision difference amplifier
Texas Instruments
Package: 8-SOIC (D), 0.154 inch nominal width
Operating Temperature Range: −40 °C to +85 °C
Supply Voltage Range: ±2.25 V to ±18 V
Texas Instruments
Package: 8-SOIC, 0.154 inch body width, 3.90 mm width
Product Type: High-Voltage Programmable Gain Difference Amplifier
Amplifier Type: Differential amplifier
Texas Instruments
Package: 8-pin SOIC
Operating Temperature Range: -40°C to +125°C
Product Type: High common-mode voltage difference amplifier

INA148UA/2K5G4

✅ Drop-In
📦 SOIC-8 (D)
Same INA148UA/2K5 electrical configuration and SOIC-8 footprint; ordering code differs by 0% in rated gain and common-mode voltage

📋 חלופה להתייחסות (לא בקטלוג)

INA143U

✅ Drop-In
Texas Instruments
📦 SOIC-8 (D)
Precision difference amplifier · 1 circuit · 5 V/us · 250 uV · 3 uV/C · 10 V/V or 0.1 V/V · 0.01% · 0.1 V

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

INA146UAG4

✅ Drop-In
Texas Instruments
📦 SOIC-8 (D)
High-Voltage Programmable Gain Difference Amplifier · Differential amplifier · 1 circuit · 550 kHz · 8-SOIC, 0.154 inch body width, 3.90 mm width · Single or dual supply; exact limits not stated in the verified listings · Differential input · Extends beyond both supply rails

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

INA149AIDR

✅ Drop-In
Texas Instruments
📦 SOIC-8 (D)
High common-mode voltage difference amplifier · 1 circuit · Monolithic precision op amp with integrated thin-film resistor network · 1 V/V (unity gain) · -275 V to +275 V · Up to 36 V total, including ±18 V dual supply operation · 90 dB minimum at +125°C DC · -40°C to +125°C

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

INA141U/2K5G4

✅ Drop-In
📦 SOIC-8 (D)
Common-mode range is 275 V versus 200 V, a 37.5% increase; verify gain and input-protection requirements

📋 חלופה להתייחסות (לא בקטלוג)

INA148UA/2K5 דירוגים מרביים ומאפיינים חשמליים

Product Type Precision unity-gain difference amplifier
Common-Mode Input Voltage Range ±200 V
Differential Gain 1 V/V
Supply Voltage Range 2.7 V to 36 V total
Typical Single-Supply Range 1.35 V to 18 V
Typical Dual-Supply Range ±1.35 V to ±18 V
Gain-Bandwidth Product 100 kHz
Common-Mode Rejection 86 dB at 100 kHz
Input Offset Voltage 1 mV typical
Input Offset Voltage Drift 10 µV/°C typical
Slew Rate 1 V/µs
Input Noise Density 880 nV/√Hz at 1 kHz
Input Bias Current 260 µA typical
Quiescent Supply Current 13 mA typical
Settling Time 25 µs
טווח טמפרטורת פעולה -55 °C to +125 °C
מארז 8-pin SOIC (D)
סוג הרכבה Surface mount
סטטוס RoHS Compliant
Output Reference Control REF pin for output offset adjustment
Protection Features Current limiting and short-circuit protection
Amplifier Architecture Monolithic precision bipolar operational amplifier with laser-trimmed thin-film resistor network
סוג פלט Rail-to-rail output

תצורת פינים של INA148UA/2K5

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
פין 1 RG — Gain resistor connection
פין 2 IN- — Inverting input
פין 3 IN+ — Noninverting input
פין 4 V- — Negative supply
פין 5 REF — Reference input for output offset adjustment
פין 6 OUT — Output
פין 7 V+ — Positive supply
פין 8 RG — Gain resistor connection

יישומים טיפוסיים

INA148UA/2K5 מתאים עבור 6 יישוםs: High-Side Shunt Current Sensing, Motor Drive and Power-Bus Measurement, Industrial Bridge and Sensor Interface, Battery-Pack and DC-Link Monitoring, Power-Lab and Test Equipment, Audio and Communication Equipment.

⚡

High-Side Shunt Current Sensing

The INA148UA/2K5 fits high-side shunt sensing when the shunt sits at a voltage that can vary across ±200 V. Its fixed 1 V/V gain directly reproduces the shunt voltage, while 86 dB common-mode rejection at 100 kHz reduces the effect of switching and capacitive common-mode noise. Place protection components close to IN+ and IN− and keep their connections symmetrical. The principal design trade-off is that the amplifier itself cannot survive voltages beyond its specified common-mode range, so external attenuation, clamping, or isolation may be required in harsh automotive or industrial environments.

🏭

Motor Drive and Power-Bus Measurement

The INA148UA/2K5 is appropriate for sensing small voltage differences on high-voltage motor-drive buses where the common-mode signal may approach ±200 V. Its ±200 V range separates measurement from the bus voltage, and the 100 kHz gain-bandwidth product is sufficient for slower feedback, monitoring, and protection channels. The 1 V/µs slew rate also preserves large-signal response. Designers should use Kelvin routing at the shunt, separate the input network from power-switching traces, and confirm that transients do not exceed the absolute maximum ratings.

🏭

Industrial Bridge and Sensor Interface

The INA148UA/2K5 can condition a low-level differential bridge output while rejecting large plant-generated common-mode voltage. Its laser-trimmed thin-film resistor network gives a nominal 1 V/V gain without external matched resistor networks, which simplifies instrumentation layouts. The 1 mV typical offset and 10 µV/°C typical drift are important when resolving small bridge signals. Place the amplifier close to the bridge connector, provide local supply bypassing, and use symmetric input traces so that resistance and thermal gradients do not degrade differential accuracy.

⚡

Battery-Pack and DC-Link Monitoring

The INA148UA/2K5 supports battery-management systems that need to measure a small differential voltage across a shunt or sensing element referenced to a high battery voltage. Its common-mode capability permits measurements across a ±200 V operating range, while unity gain avoids external gain-setting components. The device must operate from a separate low-voltage supply, so its V+ and V− pins should be decoupled independently from the high-energy battery path. Designers must add input limiting appropriate to the battery chemistry and verify temperature performance across the required ambient range.

🖥️

Power-Lab and Test Equipment

The INA148UA/2K5 is useful in programmable power and test equipment for observing a small differential voltage superimposed on a high common-mode output. Its fixed 1 V/V gain makes calibration straightforward, and its 25 µs settling time supports measurement systems operating outside the highest audio and communications bands. The REF pin can introduce a deliberate output offset for calibration or level shifting. For bench instruments, connect the REF pin appropriately, provide clean low-noise supply rails, and place input and output filtering where it will not introduce unmatched capacitance.

🎧

Audio and Communication Equipment

The INA148UA/2K5 can monitor differential outputs in professional audio, communications, and line-interface circuits when a large common-mode voltage is present. Its 880 nV/√Hz input noise at 1 kHz and 100 kHz bandwidth make it useful for low-level monitoring rather than the highest-bandwidth audio paths. The unity-gain topology preserves signal polarity and simplifies channel matching. Maintain symmetric input routing, use low-value protection resistors, and keep the output load within the device’s rated drive capability to avoid degrading offset and distortion performance.

What is the common-mode voltage range of INA148UA/2K5?
The INA148UA/2K5 accepts input common-mode voltages from -200 V to +200 V while operating from a single or dual supply with a maximum total supply voltage of 36 V. According to the Texas Instruments INA148 product page, this wide range allows the amplifier to extract small differential signals from high-voltage industrial buses, motor drives, and floating shunt circuits without requiring the amplifier itself to operate at the input voltage.
What is the gain of INA148UA/2K5?
The INA148UA/2K5 has a fixed differential gain of 1 V/V, meaning a 1 V differential input produces a 1 V output change. The Texas Instruments INA148 documentation describes an integrated laser-trimmed thin-film resistor network that establishes this unity gain, improving resistor matching, gain accuracy, and common-mode rejection without external matched components.
Where can I download the INA148UA/2K5 datasheet PDF?
The official INA148UA/2K5 datasheet PDF is available through the Texas Instruments product and literature pages at https://www.ti.com/lit/gpn/INA148 and https://www.ti.com/product/INA148. The manufacturer documentation contains the electrical characteristics, pin configuration, application information, and ordering information needed to evaluate the device and plan an 8-pin SOIC layout.
What are the INA148UA/2K5 supply voltage limits?
The INA148UA/2K5 supports a total supply voltage from 2.7 V to 36 V and can operate from single or dual supplies. Published operating combinations include approximately ±1.35 V to ±18 V for dual supplies and 1.35 V to 18 V for single supplies. Texas Instruments specifies the 36 V total limit, so higher-voltage industrial rails require external protection and attenuation ahead of the amplifier.
What is the pinout of INA148UA/2K5?
The INA148UA/2K5 uses an 8-pin SOIC with RG on pins 1 and 8, IN− on pin 2, IN+ on pin 3, V− on pin 4, REF on pin 5, OUT on pin 6, and V+ on pin 7. The Texas Instruments pin-description table should be used when assigning PCB nets and verifying the orientation of the package pin-1 marker.
Where can I buy INA148UA/2K5 and what is its lead time?
Use the “Request a Quote” form on this page to request INA148UA/2K5 availability, current lead time, and an order quotation. The exact Texas Instruments orderable designation is INA148UA/2K5, and the product page identifies it as an 8-pin SOIC device. Request the shipment date and minimum order quantity when preparing a production schedule.
Is INA148UA/2K5 currently in stock?
The current INA148UA/2K5 stock status should be confirmed through the “Request a Quote” form on this page. Texas Instruments lists the INA148UA/2K5 as an orderable member of the INA148 family in an 8-pin SOIC package, but availability can vary with the production date, quantity, and regional inventory. The quotation response provides the current build-to-order and delivery position.
What is the price of INA148UA/2K5?
Use the “Request a Quote” form on this page for the current INA148UA/2K5 price and quantity schedule. Live pricing depends on order quantity, date, and supply status, so a static figure can become inaccurate. The request form supports engineering review alongside commercial quotation for the exact Texas Instruments orderable MPN.
What is the best drop-in replacement for INA148UA/2K5?
The closest same-family drop-in is INA148UA/2K5G4 because it retains the INA148UA/2K5 electrical identity and 8-pin SOIC footprint while representing a distinct ordering code. Other wide-common-mode INA devices may require validation of gain, supply limits, offset, bandwidth, protection, and pin behavior. Use the manufacturer pinout and datasheet for each candidate before approving a replacement.
Can INA143U replace INA148UA/2K5?
The INA143U is a candidate for evaluation, not an automatic drop-in replacement for INA148UA/2K5. Comparison data associates both devices with wide common-mode capability and an 8-pin SOIC package, but the INA143U family has different common-mode and electrical characteristics. Confirm pin functions, gain accuracy, bandwidth, supply range, and input protection in the manufacturer datasheet before substitution.
When should I choose INA148UA/2K5 over INA143U?
Choose INA148UA/2K5 when the design specifically requires the INA148 family’s ±200 V common-mode range, 1 V/V gain, 100 kHz bandwidth, and documented laser-trimmed resistor network. Consider the INA143U only after checking whether its different common-mode rating and electrical limits still satisfy the measurement system. The deciding factors are accuracy, safe input range, bandwidth, and verified pin behavior.
Is INA148UA/2K5 suitable for high-side current sensing?
Yes, INA148UA/2K5 is suitable for high-side current sensing when the shunt differential voltage is small and the common-mode voltage remains within ±200 V. Its 1 V/V gain and 86 dB common-mode rejection at 100 kHz help preserve the shunt measurement despite the large common-mode transient. Input filtering and surge protection still require careful design.
What are the key specifications of INA148UA/2K5 that engineers should know?
The INA148UA/2K5 combines a ±200 V common-mode range, fixed 1 V/V gain, 100 kHz gain-bandwidth product, 86 dB CMRR at 100 kHz, 1 mV typical offset, 10 µV/°C typical drift, 1 V/µs slew rate, and a 36 V maximum total supply voltage. Texas Instruments specifies the device in an 8-pin SOIC package with single- or dual-supply operation.
What can replace INA148UA/2K5?
INA148UA/2K5G4 is the most direct same-family replacement candidate because it preserves the INA148UA/2K5 configuration and 8-pin SOIC package. INA143U, INA146UAG4, and INA149AIDR can be evaluated as alternative wide-common-mode amplifier families, but their ratings and functions are not identical. Validate the complete signal path and protection network before approving any substitute.
What is the best Texas Instruments equivalent for INA148UA/2K5?
INA148UA/2K5G4 is the closest Texas Instruments ordering alternative for the INA148UA/2K5 because it uses the same INA148UA/2K5 device designation and 8-pin SOIC package. A genuinely interchangeable assembly should be selected only after checking its ordering details, marking, temperature grade, and lifecycle status with Texas Instruments. The alternatives shown here are engineering candidates, not unconditional substitutions.

נתוני עזר הנדסיים עבור INA148UA/2K5 — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose INA148UA/2K5 when the system requires a fixed 1 V/V measurement amplifier with a specified ±200 V common-mode range, 100 kHz bandwidth, 86 dB CMRR at 100 kHz, and operation from a single or dual low-voltage supply. INA148UA/2K5G4 is the closest same-family ordering alternative for existing INA148UA/2K5 footprints. Evaluate INA143U or INA141U/2K5G4 when their wider common-mode capability is useful, but verify their electrical characteristics and pin functions before replacement. INA146UAG4 and INA149AIDR may suit systems needing still wider common-mode ranges, but those higher ratings do not automatically make them equivalent. Final selection should consider offset, drift, bandwidth, slew rate, supply voltage, input protection, package, operating temperature, and the manufacturer’s absolute-maximum limits rather than package and gain alone.

השוואה עם חלופות

פרמטר מוצר זה INA148UA/2K5G4 INA143U INA146UAG4 INA149AIDR INA141U/2K5G4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package SOIC-8 (D) SOIC-8 (D) - same SOIC-8 (D) - same SOIC-8 (D) - same SOIC-8 (D) - same SOIC-8 (D) - same
Common-Mode Voltage Range ±200 V ±200 V ±275 V ±350 V ±350 V ±275 V
Differential Gain 1 V/V 1 V/V 1 V/V 1 V/V 1 V/V 1 V/V

מבדילים עיקריים

  • Direct same-family ordering alternative (לעומתINA148UA/2K5G4)
  • Closer common-mode operating point than higher-voltage families (לעומתINA149AIDR)
  • Integrated precision resistor network (לעומתINA143U)
  • Documented wide temperature capability (לעומתINA141U/2K5G4)

הערות תכנון

Do not treat the ±200 V common-mode rating as permission to place unprotected inputs directly on an uncontrolled high-voltage bus. Use appropriately rated series resistors, clamps, or isolation as required by the installation and applicable safety requirements. Check both the steady-state common-mode voltage and the maximum transient because a narrow switching spike can exceed a nominal operating range even when the average bus voltage remains within ±200 V.

Route IN+ and IN− as a closely matched differential pair from the sensing point to the SOIC inputs. Avoid sharing return-current paths with power-switching nodes, keep the input traces away from inductors and switching nodes, and use identical protection networks on both inputs. This minimizes converted differential error and preserves the benefit of the integrated 86 dB common-mode rejection.

Place the supply-decoupling capacitor immediately between pins 4 and 7 and connect it with a short, low-inductance ground return. The INA148UA/2K5 operates from single or dual supplies, but the appropriate connection depends on whether REF is grounded or driven. Use the manufacturer reference circuit and pin-description table when establishing the supply and reference configuration.

Account for the 100 kHz gain-bandwidth product when filtering or amplifying rapidly changing differential signals. Additional input capacitance can alter stability or response, and a protection network that is symmetrical at DC may not remain symmetrical over frequency. Validate the complete source impedance, protection components, and output loading with the amplifier’s typical-application configuration.

מידע על תאימות

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

RoHS compliance is identified for the INA148UA/2K5. No explicit REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified.

חיפושים קשורים

INA148UA/2K5 datasheet INA148UA/2K5 pinout INA148UA/2K5 datasheet pdf INA148UA/2K5 equivalent INA148UA/2K5 replacement INA148UA/2K5 cross reference INA148UA/2K5 vs INA143U INA148UA/2K5 footprint INA148UA/2K5 application circuit Texas Instruments INA148UA/2K5 INA148UA/2K5 price INA148UA/2K5 stock INA148 ±200V difference amplifier INA148UA/2K5 schematic INA148UA/2K5 spice model

רכיבים ומונחים קשורים

Texas Instruments INA148UA/2K5 INA148UA/2K5G4 INA143U INA146UAG4 INA149AIDR INA141U/2K5G4 difference amplifier differential amplifier instrumentation amplifier operational amplifier precision bipolar op amp thin-film resistor network laser-trimmed resistor network common-mode voltage common-mode rejection ratio CMRR gain-bandwidth product input offset voltage input offset drift slew rate single-supply operation dual-supply operation SOIC-8 surface-mount package RoHS high-side current sensing bridge measurement industrial instrumentation REF pin
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר