IRS20954STRPBF - 2-Channel Protected Audio Driver | Infineon
MPN: IRS20954STRPBF ✓ چالاکIRS20954STRPBF گشتی
A digital audio driver is an interface and protection IC positioned between a PWM controller or digital signal processor and a power-converter stage. Within the signal chain, this category combines logic-level command processing with protection and gate-drive support. The resulting device belongs to the broader power-management IC hierarchy while providing the timing and fault-handling functions needed to operate external half-bridge power switches safely.
The principal verified features include two-channel operation, floating PWM inputs, programmable bidirectional over-current protection, automatic self-reset after a protected fault, and compensated preset dead time. Compensation of the preset dead time can reduce distortion introduced when the bridge switches between its output states. The self-reset behavior also allows the driver to recover without requiring an external system reset after the protected condition has cleared.
Because the IRS20954STRPBF is a driver rather than the audio output power stage itself, its operation depends on appropriately rated external switching devices. Its protected digital-drive architecture supports the implementation of half-bridge arrangements commonly used in audio amplification. Detailed electrical limits, propagation delays, drive-current capability, thermal ratings, and recommended external components must be confirmed in the manufacturer datasheet before layout or production use.
Typical uses include digitally controlled class-D audio amplifiers, speaker-drive power stages, compact consumer-audio systems, and industrial amplification equipment where fault recovery and controlled switching transitions are important. The floating PWM input arrangement can simplify use with systems that drive each channel using complementary or single-ended PWM information. The appropriate external MOSFETs and passive network remain application-specific.
The primary design consideration is MOSFET selection. The external devices must satisfy the application voltage, current, switching-loss, and thermal requirements, while their gate characteristics must remain compatible with the driver. PCB layout should minimize gate-loop inductance and keep switching-node copper compact. Protection settings, dead-time programming, and fault-response behavior must also be checked against the intended speaker impedance and amplifier architecture.
This page consolidates verified distributor availability, exact catalog identifiers, the documented feature set, and engineering-focused application guidance. It distinguishes confirmed data from parameters that still require the official datasheet, providing a useful starting point for sourcing and design review without assigning unsupported electrical values.
جێگرەوەکانی جێگۆڕکێ بۆ IRS20954STRPBF — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ IRS20954STRPBF (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Manufacturer, Over-Current Protection, Package.
هیچ جێگرەوەی ڕاستەوخۆ بۆ ئەم بەرهەمە بەردەست نییە.
داوای جێگرەوەکان بکەIRS20954STRPBF زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Protected digital audio driver |
| Channel Count | 2 channels |
| پاکێج | 16-pin SOIC |
| PWM Input Type | Floating PWM input |
| Over-Current Protection | Programmable bidirectional protection with self-reset |
| Dead-Time Function | Programmable compensated preset dead time |
| Topology Support | Half-bridge implementation |
| جۆری دامەزراندن | Surface mount |
| Lead Style | Leaded |
| Process Compatibility | Lead-compatible |
| Peak Reflow Compatibility | Compatible |
| Manufacturer | Infineon Technologies |
| Original Manufacturer | International Rectifier |
| Distributor Category | Audio Special Purpose |
| Distributor Description | 2-channel audio line driver |
| Minimum Order Quantity | 2500 units |
ڕێنمایی ڕێکخستنی پینی IRS20954STRPBF 16-pin soic
ڕێکخستنی پین بۆ IRS20954STRPBF (پاکێجی 16-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ IRS20954STRPBF.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
IRS20954STRPBF گونجاوە بۆ 6 بەکارھێنانs: Class-D Speaker Power Stages, Portable Consumer Audio, Digital Headphone Amplifiers, Industrial Audio Amplification, Powered Speaker Systems, Multichannel Audio Amplifier.
Class-D Speaker Power Stages
The IRS20954STRPBF fits digitally controlled class-D speaker power stages because its floating PWM inputs support half-bridge implementation and its two channels can control two output bridge sections. Programmable bidirectional over-current protection provides a defined response to abnormal output current, while self-reset allows operation to resume after the protected condition clears. Compensated preset dead time can also reduce distortion associated with switching transitions. The IC does not replace the external power MOSFETs, so device selection must account for rail voltage, speaker load, switching loss, gate characteristics, and thermal conditions.
پێشنیارکراو
Portable Consumer Audio
The IRS20954STRPBF is applicable to portable consumer-audio systems that use an external digital amplifier controller and discrete switching transistors. Its two-channel organization can reduce the number of separate protection-driver functions required for a stereo output, while the floating PWM interface supports compact half-bridge implementation. Bidirectional over-current protection and self-reset are useful in a product where output faults should not always require a full system restart. Battery-derived designs still require careful review of supply voltage, quiescent behavior, efficiency, and thermal performance once those values are obtained from the official datasheet.
پێشنیارکراو
Digital Headphone Amplifiers
The IRS20954STRPBF can be evaluated for digitally controlled headphone or line-output amplifier designs that use external switching devices rather than a monolithic output stage. Two channels suit stereo signaling, and the floating PWM inputs simplify interface with compatible digital audio controllers. Over-current protection and self-reset may improve robustness in a headphone system where load transients or accidental shorts can occur. The final choice depends on output-stage voltage, current, switching frequency, EMI objectives, and whether the selected power devices can be driven safely under all supported conditions.
پێشنیارکراو
Industrial Audio Amplification
The IRS20954STRPBF is suitable for consideration in industrial audio equipment requiring controlled output-stage faults and autonomous recovery. Its 2-channel structure supports dual audio outputs, while programmable bidirectional over-current protection addresses abnormal current in both directions. Self-reset can reduce system downtime after a transient output fault, and compensated preset dead time supports distortion-conscious operation. Industrial designs should additionally verify the device's complete electrical ratings, thermal limits, external MOSFET behavior, protection configuration, and long-term component availability against the manufacturer datasheet.
پێشنیارکراو
Powered Speaker Systems
The IRS20954STRPBF can serve in a powered-speaker architecture where a digital controller drives external half-bridge switches. Floating PWM inputs permit straightforward connection to compatible modulation circuitry, and the two channels provide a compact solution for left and right amplification. Programmable bidirectional protection is valuable when a powered speaker may encounter wiring errors, unusual loads, or output-stage disturbances. Because the driver does not directly deliver speaker power, engineers must select the external MOSFETs for voltage, current, loss, and thermal requirements and must verify startup and fault behavior in the complete amplifier.
پێشنیارکراو
Multichannel Audio Amplifier
The IRS20954STRPBF is applicable to multichannel audio systems that use one protected driver per two output channels. Its confirmed 2-channel organization and floating PWM interface allow the same building block to be repeated across left, right, center, or surround outputs. Programmed over-current protection and self-reset can standardize fault handling across multiple power stages, while compensated preset dead time supports lower distortion. System partitioning should consider synchronization between channels, control-signal routing, protection coordination, thermal design, and whether the available datasheet timing limits satisfy the chosen switching frequency.
پێشنیارکراو
داتای سەرچاوەی ئەندازیاری بۆ IRS20954STRPBF — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە |
|---|---|
| Package | 16-pin SOIC |
| Brand | Infineon Technologies |
| Product Type | Protected digital audio driver |
| Channel Count | 2 channels |
| PWM Input Architecture | Floating PWM input |
| Over-Current Protection | Programmable bidirectional protection with self-reset |
| Dead-Time Control | Programmable compensated preset dead time |
| Supported Output Topology | Half-bridge implementation |
| Minimum Order Quantity | 2500 units |
| Verified Unit Price | $1.1683 as of 2026-10-28 |
جیاکەرەوە سەرەکییەکان
- Two-channel integration reduces the number of driver devices in a stereo output (بەراورد بەSingle-channel audio-driver concepts)
- Bidirectional over-current protection with automatic recovery (بەراورد بەUnprotected basic gate-driver concepts)
- Compensated preset dead time supports lower switching distortion (بەراورد بەFixed-dead-time driver concepts)
- Floating PWM inputs simplify half-bridge implementation (بەراورد بەGround-referenced PWM-input drivers)
تێبینییەکانی دیزاین
Do not treat the IRS20954STRPBF as a self-contained audio power amplifier. It is a protected digital driver for external switching stages, so the complete design must include correctly rated MOSFETs, gate resistors, bias or level-shift components as required, and suitable DC blocking for the audio output. Verify every pin against the official 16-pin SOIC pin drawing before fabrication because the supplied web results do not include a complete pin table.
Minimize the distance between the driver outputs, gate resistors, and external MOSFET gates to reduce gate-loop inductance. Keep the high-current switching node compact and route it away from sensitive audio and control traces. Use a low-inductance ground path for the driver and power stage, place required protection and timing components close to their associated pins, and follow the layout recommendations in the official datasheet and reference circuit.
Size the external switching devices for the actual bridge voltage, output current, switching frequency, and thermal environment. The verified data does not provide the IRS20954STRPBF supply-voltage or drive-current limits, so those values must be taken from the manufacturer datasheet before selecting MOSFET gate charge, bootstrap components, or passive protection networks. Never infer safe drive conditions from the catalog category alone.
Audio amplifier EMI is influenced by switching-node dv/dt, di/dt, dead time, and output-voltage amplitude. Use the lowest switching rate that satisfies the system requirement, select external MOSFETs with controlled transition behavior, and compare the resulting harmonic spectrum with the audio specifications. Compensated preset dead time may improve distortion, but it must be configured using the datasheet's recommended method rather than relying on an external approximation.
Separate driver dissipation from MOSFET switching and conduction loss when evaluating thermal design. The supplied information does not provide junction-temperature, thermal-resistance, or drive-current figures, so a numerical junction-temperature estimate is not possible without confirmed datasheet parameters. Validate the complete amplifier across maximum load, supply voltage, fault duration, and ambient temperature rather than considering the SOIC package rating alone.
زانیاری پابەندبوون
The supplied verified search results do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this is an audio driver rather than an automotive-qualified device, but no separate automotive qualification was verified.