Texas Instruments

ISO1050DW - 5V Isolated CAN Transceiver | Texas Instruments

MPN: ISO1050DW ✓ چالاک
5.5 V Vdss 16-SOIC (0.295 inch, 7.50 mm width) Package
MOQ: 1 |

ISO1050DW گشتی

Texas Instruments ISO1050DW is an isolated 5 V CAN transceiver that complies with the ISO11898-2 standard and provides galvanic isolation up to 5000 VRMS in a 16-pin SOIC package. The device supports a maximum CAN data rate of 1 Mbps, has a typical propagation delay of 74 ns, and is specified for a maximum supply voltage of 5.5 V. Its two-channel architecture separates CAN bus and logic domains with a silicon oxide insulation barrier.

An isolated CAN transceiver is a network interface device that connects a CAN bus to a host controller while preventing high-voltage and ground-potential differences from propagating between the two systems. Within the signal-chain hierarchy, it combines a CAN physical-layer transceiver, a digital isolator, and logic-side interfaces. This galvanic isolation improves fault containment and lets equipment connected to a CAN bus operate safely when the bus and controller grounds are at different potentials.

Key electrical features include 5000 VRMS reinforced isolation for ISO1050DW, low loop delay of 150 ns typical, and transient-immunity capability of 50 kV/s typical. The logic-side and bus-side sections use separate supply domains, while failsafe outputs help define the state of the interface when the bus is inactive. The 16-SOIC package supports conventional surface-mount assembly and provides a clear path from the CAN input/output pins to the isolated logic-side TXD and RXD pins.

Technically, the ISO1050 integrates a CAN transceiver with reinforced silicon oxide isolation. The 74 ns propagation-delay specification is important for maintaining stable message timing, while the 150 ns typical loop-delay figure indicates how quickly a transition at TXD can appear at RXD through the device. Its isolation barrier separates the logic input and output buffers from the CAN bus interface, allowing isolated power to be used on the controller side when required by the system architecture.

Typical uses include industrial automation equipment, building controls, robotics, electric-vehicle subsystems, and other CAN networks where ground-potential differences are possible. The device is particularly suitable when a robust 1 Mbps bus connection and 5000 VRMS separation are required in a compact 16-pin surface-mount package.

Designers should provide separate, properly decoupled supplies to the bus-side and logic-side power pins and connect the CAN transceiver portion to the bus reference ground. The isolation barrier does not replace proper high-voltage layout practices; creepage, clearance, surge protection, and the ratings of external components must follow the complete system isolation plan.

This page consolidates verified manufacturer and distributor information, explicit data gaps, sourcing considerations, and design guidance for engineers evaluating the ISO1050DW for isolated CAN links.

جێگرەوەکانی جێگۆڕکێ بۆ ISO1050DW — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ISO1050DW (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package.

Analog Devices
Package: 16-Lead SOIC-W
بەراوردکردن لەگەڵ ISO1050DW →

هیچ جێگرەوەی ڕاستەوخۆ بۆ ئەم بەرهەمە بەردەست نییە.

داوای جێگرەوەکان بکە

ISO1050DW تایبەتمەندییەکان

Product Type Isolated CAN transceiver
CAN Standard ISO11898-2
Isolation Rating 5000 VRMS
Insulation Material Silicon oxide (SiO2)
Number of Channels 2
Propagation Delay Time 74 ns
Typical Loop Delay 150 ns
Transient Immunity 50 kV/s typical
Maximum Supply Voltage 5.5 V
Nominal Supply Voltage 5 V
Maximum Data Rate 1 Mbps
پاکێج 16-SOIC (0.295 inch, 7.50 mm width)
Number of Terminals 16
جۆری دامەزراندن Surface mount
Terminal Form Gull wing
Failsafe Outputs Supported

ڕێنمایی ڕێکخستنی پینی ISO1050DW 16-soic (0.295 inch, 7.50 mm width)

ڕێکخستنی پین بۆ ISO1050DW (پاکێجی 16-soic (0.295 inch, 7.50 mm width)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 16-soic (0.295 inch, 7.50 mm width) بۆ ISO1050DW

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ISO1050DW.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ISO1050DW گونجاوە بۆ 6 بەکارھێنانs: Industrial Automation Controllers, Robotics and Motion Systems, Building Control Networks, Electric Vehicle Subsystems, Medical and Diagnostic Equipment, Telecommunications and Data Equipment.

🏭

Industrial Automation Controllers

The ISO1050DW fits industrial automation controllers that connect a local controller to a CAN bus through a galvanic barrier. Its 5000 VRMS isolation, 1 Mbps maximum data rate, 74 ns propagation delay, and 150 ns typical loop delay support responsive communication while separating the bus domain from sensitive logic. The device is placed between the controller TXD and RXD signals and the CANH/CANL bus interface, with separate supply domains and local decoupling. Designers should add appropriately rated transient protection and maintain the required isolation clearance and creepage on the PCB.

🏭

Robotics and Motion Systems

ISO1050DW is suitable for robot controllers and motion systems where actuator buses, safety circuits, and control electronics can develop different ground potentials. The silicon oxide isolation barrier supports up to 5000 VRMS for ISO1050DW, while the 1 Mbps CAN capability and 74 ns propagation delay are appropriate for command and status traffic. The transceiver operates between host-controller logic and CAN bus pins, reducing the need for a shared high-voltage ground. Engineers still need to coordinate bus termination, surge protection, isolated power, and enclosure-level isolation requirements.

🏭

Building Control Networks

The ISO1050DW can connect building-control equipment to a CAN-based field network when controllers and building wiring are separated by substantial potential differences. Its 5000 VRMS isolation rating and 1 Mbps maximum data rate fit demanding building-automation links, and the 74 ns propagation delay supports timely message handling. In implementation, the device separates the logic TXD/RXD side from the CANH/CANL side, allowing each domain to use its own supply reference. The design must include correct bus stubs, termination, surge suppression, and compliant separation distances.

🚗

Electric Vehicle Subsystems

ISO1050DW can be used in electric-vehicle subsystems where a 1 Mbps CAN link connects control electronics to equipment operating at a different ground potential. The 5000 VRMS isolation barrier helps contain faults and electrical differences, while the 150 ns typical loop delay and 74 ns propagation delay support responsive control traffic. The transceiver handles the CANH/CANL physical layer and provides isolated TXD/RXD logic connections to the host. Compliance with vehicle-level EMC, functional-safety, and environmental requirements must be established separately from component selection.

💊

Medical and Diagnostic Equipment

ISO1050DW is applicable to medical and diagnostic equipment that uses CAN communication between isolated subsystems, provided the complete design satisfies the relevant medical electrical-safety requirements. Its 5000 VRMS isolation, 1 Mbps maximum data rate, 74 ns propagation delay, and failsafe outputs provide useful interface characteristics for separating control and bus domains. The component does not by itself establish medical certification. Designers must evaluate the full isolation network, leakage, clearance, fault behavior, external power, and applicable equipment standard.

🌐

Telecommunications and Data Equipment

ISO1050DW can support isolated CAN links in telecommunications and data equipment where backplane circuitry, external cabling, and system grounds create potential isolation concerns. The 5000 VRMS barrier and typical 50 kV/s transient immunity complement a maximum 1 Mbps CAN data rate, while the 74 ns propagation delay provides deterministic interface timing. The part is placed at the boundary between controller logic and the CAN bus, with separately filtered supplies on each side. Layout should preserve isolation boundaries and avoid placing disruptive switching nodes or unprotected copper within those boundaries.

Where to buy ISO1050DW online?
ISO1050DW can be purchased from Texas Instruments authorized distributors, including Mouser and DigiKey, or from LCSC, where the verified listing reports an in-stock price from $0.5776 as of 2026-10-28. Mouser identifies the part as a Texas Instruments 5 V isolated CAN transceiver, while the LCSC result links its product page to pricing, package information, pinout diagrams, and component data. Availability can change without notice, so buyers should confirm the exact 16-SOIC ordering code, stock position, and authorized-channel status before committing a production BOM.
What is the price of ISO1050DW?
The verified ISO1050DW price is $0.5776 per unit as of 2026-10-28, as reported by LCSC. This is the lowest listed price available in the supplied distributor data and should not be interpreted as a guaranteed volume quote. Mouser and DigiKey pages provide additional commercial inquiry and ordering channels, but the supplied snippets do not expose their complete quantity-break schedules. The JSON tier values therefore retain the verified $0.5776 floor rather than inventing unquoted prices for larger quantities.
What is the lead time for ISO1050DW?
A specific ISO1050DW lead time is not stated in the verified distributor information supplied for this product. The LCSC listing reports the component as in stock, but that statement alone does not establish a contractual lead time for every quantity. For production planning, request a current stock and lead-time quotation from LCSC, Mouser, DigiKey, or Texas Instruments with the required order quantity and date. Availability reported on 2026-10-28 should be reconfirmed at the time of purchase because distributor inventory and manufacturing schedules can change.
Is ISO1050DW in stock?
ISO1050DW is reported as in stock by LCSC in the verified data retrieved on 2026-10-27, while Heisener also displayed 13,308 pieces in its snippet. These are point-in-time distributor listings rather than a guaranteed global inventory commitment. Mouser and DigiKey product pages provide additional purchasing channels, but the supplied snippets do not state their exact stock quantities. Engineers should confirm live inventory, lot traceability, and delivery schedule when placing an order, particularly for scheduled industrial or automotive production.
What are the key specifications of ISO1050DW that engineers should know?
ISO1050DW is a 5 V isolated CAN transceiver with 5000 VRMS isolation, 1 Mbps maximum data rate, 74 ns propagation delay, and 150 ns typical loop delay. According to the Texas Instruments ISO1050 product information, it meets ISO11898-2 and separates logic-side and bus-side buffers with a silicon oxide barrier. The verified component is packaged in 16-SOIC, accepts supply voltages up to 5.5 V, includes failsafe outputs, and has typical transient immunity of 50 kV/s. These characteristics position it for isolated industrial CAN networks operating at up to 1 Mbps.
What is the isolation rating of ISO1050DW?
ISO1050DW provides galvanic isolation up to 5000 VRMS. According to the Texas Instruments ISO1050 product page, the logic input and output buffers are separated from the CAN bus side by a silicon oxide insulation barrier. The 5000 VRMS rating applies specifically to the ISO1050DW package variant; lower-rated package variants exist within the same product family. This value describes the device's specified isolation capability, but the complete installation must also satisfy applicable creepage, clearance, insulation coordination, and surge requirements.
Where to download the ISO1050DW datasheet PDF?
The official ISO1050 datasheet can be downloaded from the Texas Instruments literature link at https://www.ti.com/lit/gpn/ISO1050, while the manufacturer product page is available at https://www.ti.com/product/ISO1050. The supplied search results also identify mirrors hosted by AllDatasheet and Datasheets.com. For design review and qualification, use the TI-hosted document because it is the authoritative manufacturer source. The supplied material does not expose the datasheet revision identifier, so no revision letter or document number is inferred here.
Where can I find the ISO1050DW pinout?
The ISO1050DW uses a 16-pin SOIC package, and its connection details are included in the manufacturer datasheet available through the Texas Instruments ISO1050 literature link. The verified distributor listings also expose package and pinout resources for LCSC. Because the supplied search snippets do not provide the complete pin-number-to-signal-name table, the structured pinout field is intentionally left null rather than presenting guessed assignments. Download the official datasheet and verify every logical, supply, ground, and CAN connection before PCB design or replacement work.
ISO1050DW vs ISO1050DWR - which is better for an industrial CAN bus?
ISO1050DW and ISO1050DWR represent the same ISO1050DW device family, with the ordering suffix primarily identifying the shipping format rather than a different electrical design. The verified comparison data lists both as Texas Instruments ISO1050 isolated CAN transceivers, and the ISO1050 family provides 5000 VRMS isolation for the DW package variant. Choose the ordering code required by the authorized distributor and assembly process. A reel-versus-tube choice should not be made solely from the MPN suffix without confirming the current TI packing table.
Can ISO1042 replace ISO1050DW as a drop-in part?
No, ISO1042 is not a pin-to-pin drop-in replacement for ISO1050DW. Texas Instruments support information states that the ISO1042 SOIC-8 and ISO1050 SOIC-8 versions are not pin compatible because the RXD and TXD assignments on pins 2 and 3 are swapped; the devices also have different package pin counts in the referenced comparison. Despite both being CAN-related interface devices, ISO1042 must not be substituted without a PCB revision and a complete review of isolation, supply, logic, and bus-side requirements.
When should I choose ISO1050DW over a non-isolated CAN transceiver?
Choose ISO1050DW when the CAN bus and host electronics must be separated by up to 5000 VRMS, particularly when large ground-potential differences or fault-current paths are concerns. Its 74 ns propagation delay, 150 ns typical loop delay, failsafe outputs, and 1 Mbps capability make it suitable for robust isolated CAN links. A non-isolated transceiver may be simpler and less costly where galvanic separation is unnecessary, but it cannot provide the same electrical boundary between the bus domain and controller domain.
Is ISO1050DW suitable for industrial automation and robotics?
Yes, ISO1050DW is suitable for industrial automation and robotics when isolated CAN communication is appropriate. Its 5000 VRMS barrier, 1 Mbps maximum data rate, 74 ns propagation delay, 50 kV/s typical transient immunity, and failsafe outputs support dependable communication across electrically separated domains. The device still requires correctly decoupled bus-side and logic-side supplies, proper CAN bus termination, an appropriate surge-protection strategy, and a PCB layout that preserves the required isolation creepage and clearance.
What can replace ISO1050DW?
No verified direct drop-in replacement was identified in the supplied cross-reference results for ISO1050DW. The apparent ISO1050DWR comparison is a shipping-format variant rather than a distinct engineering alternative, while ISO1042 is explicitly not pin compatible because RXD and TXD are swapped and the referenced packages differ. Consequently, a replacement search must verify the 16-SOIC footprint, all 16 pin assignments, 5000 VRMS isolation, 5 V operation, CAN data rate, and isolation supply architecture before any substitute is approved.
Is ISO1050DW the same as ISO1050DUB?
No, ISO1050DW and ISO1050DUB are different package variants within the Texas Instruments ISO1050 family. The manufacturer product information states that ISO1050DW provides isolation up to 5000 VRMS, whereas ISO1050DUB provides up to 2500 VRMS. They are also not established by the supplied data as having the same package and pin arrangement. ISO1050DUB is therefore not a drop-in replacement for a 16-SOIC ISO1050DW design unless the PCB, isolation requirements, and every connection are independently revalidated.
What are the design considerations for using ISO1050DW in a CAN network?
The primary design considerations are supply separation, isolation safety, termination, and bus protection. According to the Texas Instruments ISO1050 information, the device separates logic-side and bus-side buffers with a silicon oxide barrier rated up to 5000 VRMS for ISO1050DW. Both isolated domains need appropriate local supply voltage and decoupling, while the CAN bus requires correct 120-ohm termination at appropriate endpoints. Keep isolation-zone copper and external components outside the required clearance and creepage boundaries, and use surge protection compatible with the CAN bus.
Does ISO1050DW meet RoHS and automotive qualification requirements?
The supplied ISO1050DW search results do not explicitly state the RoHS compliance value or identify an AEC-Q100 qualification status for this exact orderable part, so both remain unknown rather than assumed. The manufacturer, DigChip, and comparison listings reference RoHS-related information, but the snippets do not provide a verifiable status statement. Engineers should check the current TI product-page compliance declarations and the exact device qualification record. If automotive qualification is mandatory, do not infer it merely because the family supports industrial CAN applications.

داتای سەرچاوەی ئەندازیاری بۆ ISO1050DW — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose ISO1050DW when a CAN bus must be galvanically separated from host logic and the design needs up to 5000 VRMS isolation, a maximum 1 Mbps data rate, and a 16-SOIC footprint. Its 74 ns propagation delay, 150 ns typical loop delay, failsafe outputs, and 50 kV/s typical transient-immunity specification make it appropriate for industrial, robotics, building-control, telecommunications, and selected vehicle subsystem interfaces. Do not choose ISO1042 as a drop-in replacement because Texas Instruments documents incompatible RXD/TXD pin assignments and a different package comparison. ISO1050DUB offers only 2500 VRMS in the verified data, so it should not be used where the higher ISO1050DW isolation class is required. Before purchasing, confirm the current TI ordering table, reel quantity, exact price, and authorized-distributor availability.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە
Package 16-SOIC (0.295 inch, 7.50 mm width)
Brand Texas Instruments
Isolation Rating 5000 VRMS
Maximum Data Rate 1 Mbps
Propagation Delay 74 ns
Typical Loop Delay 150 ns
Maximum Supply Voltage 5.5 V
Transient Immunity 50 kV/s typical
Number of Channels 2
CAN Standard ISO11898-2

جیاکەرەوە سەرەکییەکان

  • Higher verified isolation rating within the ISO1050 family (بەراورد بەISO1050DUB)
  • No direct drop-in substitution due to incompatible pin assignments (بەراورد بەISO1042)
  • Fast isolated CAN interface for control and monitoring networks (بەراورد بەISO1050DWR)

تێبینییەکانی دیزاین

Preserve the isolation boundary across the entire PCB, not only beneath ISO1050DW. Keep the logic-side and bus-side ground planes, copper pours, test points, and external components separated according to the required working voltage and pollution degree. Avoid placing high-voltage or fast-switching copper under the device where creepage and capacitance could reduce isolation performance. The 5000 VRMS device rating does not determine the layout spacing by itself; use the complete system insulation requirements and the manufacturer guidance.

Provide independently referenced supplies to the logic-side and bus-side sections, each within the 5.5 V maximum verified limit. Place local high-frequency bypass capacitors at the relevant supply and ground pins and keep their return paths short. The isolated power source must have adequate isolation and capacitance characteristics for the operating frequency. Confirm startup, shutdown, bus-active, and bus-inactive behavior because correct voltage sequencing and stable references are essential to predictable CAN communication.

Do not substitute ISO1042 for ISO1050DW without a PCB redesign. Texas Instruments support information identifies swapped RXD and TXD assignments on pins 2 and 3 for the compared SOIC-8 versions, and the package sizes differ. ISO1050DUB also has a lower verified isolation rating of 2500 VRMS compared with 5000 VRMS for ISO1050DW. Check the complete ordering table, isolation class, pin assignments, and supply domains before approving any alternate part.

Implement the CAN bus protection and termination strategy as part of the interface rather than relying solely on the transceiver. Use the appropriate bus termination at the physical endpoints, minimize stub length, and select surge-protection devices whose capacitance and clamp behavior are compatible with the 1 Mbps maximum data rate. Keep protection current away from the isolation barrier and verify it for the required industrial transient environment. The verified 50 kV/s typical transient-immunity figure describes the device, not the complete protected system.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The verified snippets mention RoHS information but do not provide an explicit compliance value. No REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was provided for ISO1050DW; these fields are therefore left unknown rather than inferred.

داتا پشتڕاستکراوەتەوە لە: 2026-10-28 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ISO1050DW ISO1050DW datasheet Texas Instruments ISO1050DW ISO1050DW 5000 VRMS isolated CAN transceiver ISO1050DW 16-SOIC ISO1050DW 1 Mbps CAN ISO1050DW industrial CAN isolation ISO1050DW vs ISO1042 ISO1050DW vs ISO1050DUB ISO1050DW drop-in replacement ISO1050DW buy price ISO1050DW pinout

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments ISO1050DW ISO1050DWR ISO1050DUB ISO1042 isolated CAN transceiver CAN transceiver digital isolator network interface IC semiconductor ISO11898-2 silicon oxide insulation barrier galvanic isolation 5000 VRMS isolation 16-SOIC package SOIC surface-mount package 1 Mbps CAN data rate 74 ns propagation delay 150 ns loop delay 50 kV/s transient immunity failsafe output CAN bus industrial automation electric vehicle
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ