Texas Instruments

LM2902KAVQPWRG4Q1 - Quad 30V Automotive Op Amp | TI

MPN: LM2902KAVQPWRG4Q1 ✓ چالاک
30 V Vdss 0.5 µA Id 14-TSSOP Package
MOQ: 1 |

LM2902KAVQPWRG4Q1 گشتی

Texas Instruments LM2902KAVQPWRG4Q1 is a four-circuit general-purpose operational amplifier designed for automotive and industrial equipment. It combines a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, 2 mV input-offset-voltage rating, 0.5 V/µs slew rate, and 2 kV ESD protection in a 14-pin TSSOP package. The four amplifiers are independent and frequency compensated, allowing one package to implement multiple analog signal-conditioning stages without requiring four separate devices.

An operational amplifier is an analog amplifier that uses very high open-loop gain to amplify the difference between two input voltages. Within the larger semiconductor hierarchy, this device belongs to the operational-amplifier family, analog IC category, and signal-conditioning ecosystem. Its wide supply range, low supply-current drain, and common-mode input capability make it suitable for circuits that must operate from single or split supplies across demanding temperature environments.

The LM2902KAVQPWRG4Q1 provides a 1.2 MHz gain-bandwidth product for general-purpose closed-loop amplification. Its 0.5 V/µs slew rate supports moderate-frequency signal changes, while 2 mV input offset voltage limits systematic input-referred error. The K-suffix device adds 2 kV ESD protection, and the Q1 grade supports automotive qualification requirements. A typical supply-current drain of 0.8 mA per amplifier also helps limit consumption in multi-amplifier signal chains.

Each internal amplifier is independently compensated and operates from a single supply or from split supplies when the total supply span permits operation. The device maintains low-voltage behavior and remains usable across a wide common-mode input range. Input differential voltages greater than 0.5 V should not be applied continuously because they can cause input-offset-voltage shift beyond the specified maximum, with the magnitude increasing as ambient temperature rises.

Typical uses include automotive sensor conditioning, transducer amplification, active filtering, voltage buffering, differential sensing, and low-frequency closed-loop control loops. Four independent amplifiers can reduce package count when a circuit needs multiple stages, such as an instrumentation front end combining input conditioning, gain, filtering, and output buffering.

Design layouts should reserve clean return paths for each amplifier, place input and output components near their associated pins, and avoid long parallel traces that can increase noise pickup. Check supply decoupling, output loading, common-mode headroom, and stability before finalizing the circuit. Because a quad device contains four amplifiers, verify every channel’s gain-bandwidth and stability configuration rather than assuming every stage has identical loading.

This page consolidates the manufacturer’s electrical ratings, automotive-ordering information, package details, application guidance, comparison data, and practical PCB considerations into a design-focused reference for engineers evaluating the LM2902KAVQPWRG4Q1 and its pin-compatible family option.

جێگرەوەکانی جێگۆڕکێ بۆ LM2902KAVQPWRG4Q1 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2902KAVQPWRG4Q1 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Automotive Qualification, Number of Amplifier Channels.

Texas Instruments
Automotive Qualification: AEC-Q100 qualified
Number of Amplifier Channels: 4 channels
بەراوردکردن لەگەڵ LM2902KAVQPWRG4Q1 →

LM2902KAVQPWRQ1

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 14-TSSOP
4 channels · 3 V to 32 V · 30 V · 1.2 MHz · 2 mV · 0.5 V/µs · 2 kV · Includes ground

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902KAVQPWRG4Q1 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type 4-circuit general-purpose operational amplifier
Number of Amplifier Channels 4 circuits
Maximum Supply Voltage 30 V
Single-Supply Operating Range 5 V to 26 V
Dual-Supply Operating Span Up to 26 V total
Gain-Bandwidth Product 1.2 MHz
Input Offset Voltage 2 mV
Slew Rate 0.5 V/µs
Common-Mode Rejection Ratio 80 dB
Input Bias Current 0.5 µA
Supply-Current Drain 0.8 mA typical per amplifier
ESD Protection 2 kV
مەودای پلەی گەرمیی کارکردن -55 °C to +125 °C
Package Type 14-TSSOP
ژمارەی پینەکان 14 pins
جۆری دامەزراندن Surface mount
Automotive Qualification AEC-Q100 qualified Q1 grade

ڕێنمایی ڕێکخستنی پینی LM2902KAVQPWRG4Q1 14-tssop

ڕێکخستنی پین بۆ LM2902KAVQPWRG4Q1 (پاکێجی 14-tssop). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 14-tssop بۆ LM2902KAVQPWRG4Q1

هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM2902KAVQPWRG4Q1.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

LM2902KAVQPWRG4Q1 گونجاوە بۆ 6 بەکارھێنانs: Automotive Sensor Signal Conditioning, Industrial Transducer Amplification, Active Filtering and Signal Conditioning, Battery Monitoring and Control Loops, Audio and Communication Interface Buffers, Test and Measurement Front Ends.

🚗

Automotive Sensor Signal Conditioning

The LM2902KAVQPWRG4Q1 fits automotive sensor-conditioning chains that require several low-frequency analog stages in one package. Its four independent amplifiers can provide input buffering, gain, active filtering, and output driving without using four separate packages. The 30 V maximum supply rating supports systems with automotive transient margins, while 2 kV ESD protection adds useful robustness at sensitive sensor interfaces. The 80 dB common-mode rejection ratio and 2 mV input-offset-voltage rating help preserve accuracy when the source is close to the measurement ground. Designers must still check the common-mode range at the actual 5 V to 26 V operating supply and prevent sustained differential inputs above 0.5 V.

🏭

Industrial Transducer Amplification

The LM2902KAVQPWRG4Q1 is suitable for amplifying low-level pressure, temperature, and position transducer signals in industrial control equipment. Its 1.2 MHz gain-bandwidth product supports closed-loop gains appropriate for moderate-bandwidth measurement channels, while the 0.5 V/µs slew rate reduces distortion risk when signals must transition rapidly. Four channels permit a practical architecture comprising two sensor amplifiers, a filter, and an output buffer. The typical 0.8 mA per-amplifier supply-current drain helps manage power in distributed instrumentation, and the -55 °C to +125 °C range covers harsh environments. Validate the actual input common-mode voltage, output swing, noise, and stability at the selected closed-loop gain.

🔧

Active Filtering and Signal Conditioning

The four independent amplifiers in the LM2902KAVQPWRG4Q1 make it practical to implement cascaded active-filter and conditioning stages in a compact analog module. A 1.2 MHz gain-bandwidth product provides useful bandwidth for low-frequency filter sections, and the 2 mV input-offset-voltage rating limits DC error in gain stages. Two channels can form a precision filter topology while the remaining channels perform anti-alias filtering, level shifting, or output buffering. The 30 V supply capability permits operation from higher-voltage industrial rails, subject to the common-mode and output-swing limits. Validate each stage independently because four amplifiers in one package do not eliminate the need to check per-channel loading, stability, and thermal performance.

⚡

Battery Monitoring and Control Loops

The LM2902KAVQPWRG4Q1 can implement low-frequency battery-cell monitoring, current-sense amplification, and control functions where a 30 V-rated device simplifies supply-headroom planning. Its typical 0.8 mA supply-current drain per channel is valuable when four amplifiers must operate continuously in a battery-backed controller. The 2 mV input offset contributes to accuracy budget, while 2 kV ESD protection supports robustness in connector-exposed circuitry. Four channels might handle cell voltage conditioning, current sensing, a threshold comparator, and an output-buffer stage. The circuit must keep differential inputs below 0.5 V during fault conditions and must verify that the common-mode input range remains valid at the minimum battery or supply voltage.

🎧

Audio and Communication Interface Buffers

The LM2902KAVQPWRG4Q1 can provide impedance buffering, gain, and summing functions in low-frequency audio or communication-interface circuits. Its 0.5 V/µs slew rate is suitable for many baseband and control-bandwidth signals, while the four-channel configuration can support source selection, differential summing, output isolation, and gain stages in one package. A 30 V maximum supply rating offers flexibility for legacy interface circuits operating from elevated rails. Audio designers should still evaluate noise density, output drive, channel-to-channel behavior, and distortion at the intended frequency because the published headline specifications do not describe every audio-quality metric. Confirm the output-load limits and loop stability in the final topology.

📺

Test and Measurement Front Ends

The LM2902KAVQPWRG4Q1 suits multi-channel test and measurement front ends that require instrumentation-style buffering and low-frequency amplification in a compact package. Four independent channels can amplify sense-node signals, drive an analog filter, buffer a reference path, and provide an output driver. Its 80 dB common-mode rejection ratio and 2 mV offset rating help control errors in instrumentation circuits, while the -55 °C to +125 °C operating range supports demanding equipment. The 1.2 MHz gain-bandwidth product is appropriate for many low- and moderate-bandwidth measurements. Evaluate input bias current, output swing, capacitive loading, noise, and calibration requirements against the complete measurement chain.

What is the LM2902KAVQPWRG4Q1?
The LM2902KAVQPWRG4Q1 is a Texas Instruments quad operational amplifier with four independent, frequency-compensated amplifiers. According to the LM2902KAV manufacturer datasheet, it supports a maximum 30 V supply, a 1.2 MHz gain-bandwidth product, a 2 mV input-offset-voltage rating, and 2 kV ESD protection. The device is packaged in 14-pin TSSOP and is intended for automotive and industrial signal-conditioning equipment requiring multiple amplifier channels in one package.
What is the operating voltage of LM2902KAVQPWRG4Q1?
The LM2902KAVQPWRG4Q1 operates from 5 V to 26 V on a single supply or across up to 26 V total on split supplies. According to the Texas Instruments LM2902KAV manufacturer datasheet, its maximum supply rating is 30 V. Designers must also maintain sufficient common-mode input headroom and output-voltage range for every selected channel, because the supply-voltage limit alone does not guarantee linear operation at every input and output level.
What are the key specifications of LM2902KAVQPWRG4Q1 that engineers should know?
The principal ratings are 30 V maximum supply voltage, 1.2 MHz gain-bandwidth product, 2 mV input offset voltage, 0.5 V/µs slew rate, and 2 kV ESD protection. The Texas Instruments LM2902KAV manufacturer datasheet also identifies four independent amplifier channels, an 80 dB common-mode rejection ratio, approximately 0.5 µA input bias current, and a typical 0.8 mA supply-current drain. Its operating-temperature range extends from -55 °C to +125 °C.
Where can I download the LM2902KAVQPWRG4Q1 datasheet PDF?
The authoritative LM2902KAVQPWRG4Q1 information is available from the Texas Instruments LM2902KAV product page at https://www.ti.com/product/LM2902KAV. The linked manufacturer datasheet provides the authoritative ordering table, electrical characteristics, pin configuration, and application information. Use the manufacturer PDF for design sign-off because secondary document mirrors may use different revisions or include material outside the current ordering context.
Where can I find the LM2902KAVQPWRG4Q1 pinout?
Use the pin-configuration diagram and pin-description table in the Texas Instruments LM2902KAV manufacturer datasheet. The component is a 14-pin TSSOP containing four operational amplifiers, and the package drawing must be matched to the QPW ordering code rather than inferred from a generic SOIC-14 drawing. Verify channel assignment, supply pins, output pins, and input pins against the exact datasheet revision used for PCB release.
Can LM2902KAVQPWRQ1 replace LM2902KAVQPWRG4Q1?
The LM2902KAVQPWRQ1 is the closest ordering option shown for direct comparison and is identified as a 14-TSSOP, four-circuit device. It is therefore the relevant drop-in candidate to evaluate for the LM2902KAVQPWRG4Q1. Final substitution still requires checking the exact ordering table for grade, temperature, ESD, qualification, and lifecycle differences rather than relying on the shared package alone.
LM2902KAVQPWRG4Q1 vs LM2902KAVQPWRQ1 - which is better for automotive use?
Choose the LM2902KAVQPWRG4Q1 when the finished vehicle application requires the explicitly identified Q1 automotive grade. The LM2902KAVQPWRQ1 is a closely related 14-TSSOP part and is the leading pin-compatible candidate for cost or availability evaluation. Compare the manufacturer ordering table for qualification markings, temperature coverage, ESD suffix, and lifecycle status before approving either part for a production automotive design.
What is the best drop-in replacement for LM2902KAVQPWRG4Q1?
The LM2902KAVQPWRQ1 is the best-supported drop-in candidate identified for the LM2902KAVQPWRG4Q1 because it is presented as a direct 14-TSSOP comparison and shares the quad general-purpose operational-amplifier configuration. Only one qualified drop-in candidate is documented here. Other LM2902 package variants should not be treated as drop-in alternatives unless their package dimensions and pin assignments are independently confirmed.
When should I choose LM2902KAVQPWRG4Q1 instead of another quad op amp?
Choose the LM2902KAVQPWRG4Q1 when the design needs four independent amplifiers, a high-voltage supply capability of 30 V, a 1.2 MHz gain-bandwidth product, 2 kV ESD protection, and operation from -55 °C to +125 °C. It is particularly suitable when package consolidation and automotive-grade sourcing matter. A lower-voltage, rail-to-rail, or higher-precision amplifier may be preferable when those different performance priorities dominate.
Is the LM2902KAVQPWRG4Q1 suitable for sensor conditioning?
Yes, the LM2902KAVQPWRG4Q1 is suitable for many sensor-conditioning stages because its 80 dB common-mode rejection ratio, 2 mV input-offset-voltage rating, and 1.2 MHz gain-bandwidth product support low-frequency measurement circuits. Its four independent channels can amplify, filter, level-shift, and buffer signals. Verify sensor excitation requirements, input common-mode range, output swing, noise performance, and stability at the intended closed-loop gain.
How should the LM2902KAVQPWRG4Q1 be protected from excessive differential input voltage?
Keep continuous differential input voltage below 0.5 V for the LM2902KAVQPWRG4Q1. The Texas Instruments manufacturer datasheet warns that larger sustained differential inputs can shift input offset voltage beyond its maximum specification, and the effect becomes larger as ambient temperature rises. Use series input resistance, clamp structures, or an external differential clamp when sensor fault conditions can apply a larger voltage.
What is the power dissipation of LM2902KAVQPWRG4Q1?
The Texas Instruments LM2902KAV manufacturer datasheet gives a typical supply-current drain of 0.8 mA per amplifier, but it does not provide a single fixed total because dissipation depends on supply voltage, output loading, and the number of active channels. Calculate each channel as approximately the average supply voltage multiplied by its current draw, then include quiescent dissipation from all four amplifiers. Use the package thermal data and actual board copper for junction-temperature analysis.
Where to buy LM2902KAVQPWRG4Q1 online?
Use the Request a Quote form on this page to request current LM2902KAVQPWRG4Q1 availability, lead time, and an order quote. The manufacturer ordering code identifies a 14-TSSOP automotive quad operational amplifier, and its grade, temperature range, and qualification requirements should be confirmed during procurement. Provide the target quantity and manufacturing schedule so the quotation reflects the correct packaging and delivery conditions.
What is the price and lead time for LM2902KAVQPWRG4Q1?
The current price and lead time for LM2902KAVQPWRG4Q1 should be requested through the Request a Quote form on this page. Market pricing can change with quantity, package configuration, market conditions, and sourcing availability, so a static figure would not represent a reliable commitment. Include your required quantity, date code preference, shipping destination, and qualification documentation requirements in the request.
Is LM2902KAVQPWRG4Q1 in stock?
Current LM2902KAVQPWRG4Q1 inventory status should be confirmed through the Request a Quote form on this page. Because this page does not publish a live stock count, the part should not be treated as immediately available without written confirmation. State your required quantity, target delivery date, approved manufacturer list, and any date-code or traceability requirements when requesting the quotation.

داتای سەرچاوەی ئەندازیاری بۆ LM2902KAVQPWRG4Q1 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM2902KAVQPWRG4Q1 when the design needs four independent general-purpose amplifiers, a 30 V maximum supply rating, 2 kV ESD protection, and operation across -55 °C to +125 °C. It is particularly appropriate for automotive sensor interfaces, industrial transducers, active filters, and multi-stage signal-conditioning blocks where package consolidation is valuable. The LM2902KAVQPWRQ1 is the closest documented drop-in option when procurement needs an alternate ordering code, but its qualification, ESD, temperature, and lifecycle details should be confirmed against the manufacturer ordering table. For designs requiring rail-to-rail inputs, very low offset, higher bandwidth, or output swing close to the supply rails, select a different precision or rail-to-rail amplifier family. For every candidate, verify the exact pin arrangement, common-mode range, output swing, capacitive-load stability, and thermal performance.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2902KAVQPWRQ1
Brand Texas Instruments Texas Instruments
Package 14-TSSOP 14-TSSOP
Amplifier Channels 4 circuits 4 circuits

جیاکەرەوە سەرەکییەکان

  • Combines four amplifiers with automotive-grade ordering (بەراورد بەLM2902KAVQPWRQ1)
  • Provides enhanced ESD protection for exposed analog inputs (بەراورد بەLM2902KAVQPWRQ1)
  • Supports extended high-temperature operation (بەراورد بەLM2902KAVQPWRQ1)

تێبینییەکانی دیزاین

Do not allow continuous differential input voltage to exceed 0.5 V. The Texas Instruments manufacturer datasheet warns that larger sustained differentials can shift input offset voltage beyond its specified maximum, and the shift becomes more significant as ambient temperature rises. Add series impedance or a suitable clamp at inputs that can receive transients or sensor faults, and verify the clamp does not disrupt signal bandwidth.

Place each input, output, supply, and bypass connection close to its associated device pin. Keep the four amplifier returns connected to a low-impedance ground plane, and avoid routing sensitive inputs beside switching nodes, inductors, or high-current return paths. Because the device contains four amplifiers, verify channel assignment on the manufacturer pin diagram and inspect every channel’s feedback components rather than assuming a symmetric layout.

Calculate dissipation for all four channels rather than the no-load quiescent current alone. A useful first estimate is the average voltage across each amplifier multiplied by its supply-current demand, with the sum adjusted for output load. Keep in mind that the device can operate from 5 V to 26 V, so dissipation changes substantially across the supply range. Use the package thermal information and actual PCB copper area for junction-temperature calculations.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The G4Q1 designation and the LM2902-Q1 manufacturer product family identify an automotive-qualified part. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated in the cited product information.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2902KAVQPWRG4Q1 datasheet LM2902KAVQPWRG4Q1 datasheet pdf LM2902KAVQPWRG4Q1 pinout LM2902KAVQPWRG4Q1 equivalent LM2902KAVQPWRG4Q1 replacement LM2902KAVQPWRG4Q1 cross reference LM2902KAVQPWRG4Q1 vs LM2902KAVQPWRQ1 LM2902KAVQPWRG4Q1 price LM2902KAVQPWRG4Q1 stock Texas Instruments LM2902KAVQPWRG4Q1 LM2902KAVQPWRG4Q1 automotive op amp LM2902KAVQPWRG4Q1 14-TSSOP

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM2902KAVQPWRG4Q1 LM2902KAVQPWRQ1 LM2902KAV LM2902-Q1 quad operational amplifier operational amplifier op amp analog amplifier analog IC semiconductor signal conditioning active filter transducer amplifier automotive electronics industrial control AEC-Q100 RoHS REACH 14-TSSOP TSSOP package family surface-mount package gain-bandwidth product input offset voltage common-mode rejection ratio ESD protection
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ