onsemi

LM2903DG - Dual Comparator, 2-36V, SOIC-8 | onsemi

MPN: LM2903DG ✓ چالاک
2 V to 36 V Vdss 0.4 mA (typical, largely independent of VCC) Id SOIC-8 (D suffix), 8 pins Package
MOQ: 1 |

LM2903DG گشتی

The onsemi LM2903DG is a dual differential voltage comparator with open-collector outputs, low input offset voltage of 2 mV typical, and a wide supply voltage range of 2V to 36V (single supply) or +/-1V to +/-18V (split supply), housed in an 8-pin SOIC package rated from -40C to +105C.

A voltage comparator is an analog IC that compares two input voltages and outputs a digital signal indicating which input is higher. It sits at the boundary between the analog and digital domains within the signal-chain hierarchy: comparator -> analog front-end IC -> signal conditioning -> power/semiconductor. The LM2903 family, originally introduced as the LM393 series, is the industry-standard general-purpose comparator, and the LM2903 variant extends the temperature range for industrial use.

Key features include two independent comparators in one package, open-collector outputs that support rail-to-rail output swings and wired-OR configurations, a common-mode input range that extends down to ground (negative rail) during single-supply operation, and a very low supply-current drain of approximately 0.4 mA per comparator that is largely independent of supply voltage. Input offset voltage as low as 2 mV makes the device suitable for precision threshold detection.

Technically, the device permits single- or split-supply operation as long as the difference between the two supplies is 2V to 36V and VCC is at least 1.5V more positive than the input common-mode voltage. Typical propagation delay (response time) is approximately 1.3 us, adequate for threshold detection, level shifting, and slow-to-medium speed switching tasks. The open-collector stage requires an external pull-up resistor to define the logic-high level, allowing direct interfacing to 5V, 3.3V, or other logic families.

Typical applications include limit comparators and over-voltage/under-voltage detectors in power supplies, window comparators in battery-management and industrial monitoring circuits, zero-crossing detection, oscillator and pulse-generator timing circuits, and logic-level translation in automotive and industrial controllers where the -40C to +105C range is required.

When designing with the LM2903DG, add hysteresis (a small positive-feedback resistor around the comparator) to prevent output chatter near slowly changing input thresholds, and place a pull-up resistor of 1k to 100k on each output.

This page consolidates distributor availability data, pin-compatible drop-in alternatives from multiple manufacturers, and practical design notes that go beyond the manufacturer datasheet alone.

جێگرەوەکانی جێگۆڕکێ بۆ LM2903DG — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903DG (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Comparator Type, Common-Mode Input Range, Output Type, Operating Temperature Range.

Texas Instruments
Package: 8-SOIC (D), 3.90 mm body width
Comparator Type: Differential
Output Type: Open-Collector (Open-Drain)
بەراوردکردن لەگەڵ LM2903DG →
Texas Instruments
Package: 8-pin SOIC, 0.154 inch (3.90 mm) width
Comparator Type: Dual differential comparator
Common-Mode Input Range: Includes ground
بەراوردکردن لەگەڵ LM2903DG →
Texas Instruments
Package: 8-pin SOIC
Comparator Type: Dual differential comparator
Output Type: Open-collector
بەراوردکردن لەگەڵ LM2903DG →
onsemi
Package: 8-pin SOIC
Comparator Type: Dual differential voltage comparator
Common-Mode Input Range: Extended to ground with single-supply operation
بەراوردکردن لەگەڵ LM2903DG →
onsemi
Package: 8-SOIC
Comparator Type: Dual differential voltage comparator
Common-Mode Input Range: Rail-to-rail
بەراوردکردن لەگەڵ LM2903DG →
Texas Instruments
Package: 8-pin SOIC, 0.154 inch width and 3.90 mm width
Comparator Type: Dual differential voltage comparator
Output Type: Open-collector
بەراوردکردن لەگەڵ LM2903DG →
Texas Instruments
Package: 8-pin SOIC
Comparator Type: Dual differential comparator
Common-Mode Input Range: Includes ground
بەراوردکردن لەگەڵ LM2903DG →
Texas Instruments
Package: 8-pin SOIC, 3.90 mm width
Comparator Type: Dual differential comparator
Output Type: Open-collector
بەراوردکردن لەگەڵ LM2903DG →
Texas Instruments
Package: 8-pin SOIC
Comparator Type: Dual differential comparator
Output Type: Open collector
بەراوردکردن لەگەڵ LM2903DG →
onsemi
Package: 8-SOIC (SOIC-8), 1.27 mm lead pitch
Comparator Type: Precision, dual, independent
Common-Mode Input Range: Includes ground (single supply operation)
بەراوردکردن لەگەڵ LM2903DG →
onsemi
Package: 8-pin SOIC
Comparator Type: Precision voltage comparator
Common-Mode Input Range: Includes ground under single-supply operation
بەراوردکردن لەگەڵ LM2903DG →

LM2903DR2G

✅ جێگرەوەی ڕاستەوخۆ
onsemi
📦 SOIC-8
Dual differential voltage comparator · 2 channels · 2 independent channels · 2 V to 36 V · ±1 V to ±18 V · Open collector · 1.5 µs · 2.0 mV

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393DG

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
onsemi
📦 SOIC-8
Precision voltage comparator · 2 independent channels · 2 V to 36 V · 2.0 mV minimum · 1.3 µs · Open-collector · Single or split supply · Includes ground under single-supply operation

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903DR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
Dual differential comparator · 2 channels · 2 V to 36 V · Open-collector · 300 ns · 8-pin SOIC · Surface mount · -40 °C to +125 °C

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903DRG4

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
Dual differential comparator · 2 · Open-collector · 2 V to 30 V · 30 V · 2 V to 36 V total supply difference · ±38 V · Includes ground

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903AVQDRG4Q1

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
Differential · 2 · Open-Collector (Open-Drain) · 2 V to 36 V · +/-1 V to +/-18 V · 0.4 mA typ, independent of supply voltage · AEC-Q100 Grade 0 and Grade 1 · -40 °C to +125 °C

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903QDRQ1

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
Dual differential comparator · 2 · AEC-Q100 Grade 0 and Grade 1 · 2 V to 36 V · Total supply difference of 2 V to 36 V · 0.4 mA per comparator · 2 mV typical · 25 nA typical

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903DG زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Channels 2 (dual independent comparators)
Comparator Type General purpose, differential
جۆری دەرچوون Open-collector, rail-to-rail output swing
Supply Voltage Range (Single) 2 V to 36 V
Supply Voltage Range (Split) +/-1 V to +/-18 V
Input Offset Voltage (Typ) 2 mV
Response Time / Propagation Delay 1.3 us (typical)
Supply Current per Comparator 0.4 mA (typical, largely independent of VCC)
Common-Mode Input Range Includes ground (negative rail) in single-supply operation
Maximum Supply Voltage Rating 36 V (V-suffix devices tested to 32 V)
Minimum VCC Above Common-Mode 1.5 V
مەودای پلەی گەرمیی کارکردن -40C to +105C
پاکێج SOIC-8 (D suffix), 8 pins
جۆری دامەزراندن Surface Mount
Description Category Low Offset Voltage Dual Comparators

ڕێکخستنی پینی LM2903DG

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 OUT A — Open-collector output of comparator A (requires pull-up)
پین 2 IN A- — Inverting input of comparator A
پین 3 IN A+ — Non-inverting input of comparator A
پین 4 GND / V- — Ground or negative supply
پین 5 IN B+ — Non-inverting input of comparator B
پین 6 IN B- — Inverting input of comparator B
پین 7 OUT B — Open-collector output of comparator B (requires pull-up)
پین 8 VCC / V+ — Positive supply, 2V to 36V (single) or +1V to +18V (split)

بەکارهێنانە باوەکان

LM2903DG گونجاوە بۆ 6 بەکارھێنانs: Over-Voltage / Under-Voltage Detection in Power Supplies, Window Comparators for Battery Management, Zero-Crossing and Threshold Detection, Oscillators and Pulse/Timing Generators, Logic-Level Translation and Interface Buffers, Automotive and Industrial Sensing Front-Ends.

⚡

Over-Voltage / Under-Voltage Detection in Power Supplies

The LM2903DG's wide 2V to 36V supply range and 2 mV typical input offset make it a natural supervisor for AC-DC and DC-DC power rails. One comparator monitors an output rail against a resistor divider from a reference, while the second monitors a second rail, giving dual-rail supervision in a single SOIC-8. Because the common-mode input range extends to ground, rails referenced to 0V are sensed directly without biasing tricks. The open-collector outputs drive an optocoupler LED or a fault-flag pull-up, and the -40C to +105C rating covers industrial PSU ambient conditions. Estimated: with a 5V rail divided to 2.5V at the input, the 2 mV offset corresponds to roughly 0.08% trip-point accuracy before divider tolerance.

🔋

Window Comparators for Battery Management

A window comparator uses both LM2903DG comparators to detect when a battery voltage leaves an acceptable band: one comparator trips on over-voltage, the other on under-voltage, and the wired-OR open-collector outputs combine into a single fault signal without extra glue logic. The 0.4 mA per-comparator supply current keeps quiescent drain low in battery-powered monitors, and the 2 mV offset supports thresholds accurate to tens of millivolts at typical lithium-cell voltages. Single-supply 2V operation covers low cell counts, while the 36V rating survives stacked-cell and charger transients. Per the datasheet, VCC must stay at least 1.5V above the common-mode input, which is satisfied at normal cell voltages.

🏭

Zero-Crossing and Threshold Detection

In AC mains synchronization, motor back-EMF sensing, and signal-level slicing, the LM2903DG compares an analog waveform against a threshold and produces a clean logic edge. Its approximately 1.3 us typical response time is adequate for 50/60 Hz zero-crossing detection, where microsecond accuracy corresponds to sub-0.1-degree phase error, and for comparator-based motor commutation in low-cost drives. The common-mode range to ground allows direct sensing of ground-referenced signals, and hysteresis added with a positive-feedback resistor prevents multiple transitions on noisy crossings. Estimated: for a 1 V/ms slew input and 10 mV of hysteresis, chatter band dwell time is about 10 us, comfortably resolvable by the 1.3 us response time.

🔧

Oscillators and Pulse/Timing Generators

An LM2903DG comparator with an RC network and positive feedback forms a relaxation oscillator, and with two comparators you can build windowed monostables or duty-cycle-controlled clocks in one SOIC-8. The open-collector output charges and discharges the timing capacitor through the pull-up and feedback resistors, with frequency set by estimated f = 1/(2RC ln(2)) for the classic configuration. The device's low input bias current minimizes timing error at high-impedance RC values, and the 2-36V supply range lets the same oscillator run from 5V logic rails or 24V industrial panels. Response time of about 1.3 us sets the practical upper frequency floor in the hundreds-of-kilohertz range.

🌐

Logic-Level Translation and Interface Buffers

Because the LM2903DG output only sinks current and floats high through a pull-up, the high level is defined by whichever supply the pull-up resistor connects to - enabling comparison of a 3.3V-domain signal and delivery of a 5V or 24V-domain output with a single comparator. This makes it a robust one-bit level translator in mixed-voltage industrial I/O, PLC input cards, and sensor interfacing. The 36V absolute supply rating allows the pull-up to sit on 24V rails while inputs sense low-voltage logic, and the -40C to +105C range covers unconditioned factory environments. Estimated: with a 10k pull-up to 24V, output sink current at saturation is about 2.4 mA, well within open-collector capability.

🚗

Automotive and Industrial Sensing Front-Ends

The LM2903DG's -40C to +105C operating range and tolerance of wide supply excursions make it suited to automotive body electronics and industrial sensor monitoring - coolant-level switches, pressure-switch thresholds, lamp-failure detection, and comparator-based quadrature decoding. The open-collector outputs directly drive relays, LEDs, or MCU interrupt inputs through pull-ups on the vehicle's battery-supplied domain, and the 36V rating absorbs load-dump clamped transients within limits. Input offset of 2 mV typical supports millivolt-level bridge and thermistor threshold decisions. For designs requiring formal AEC-Q100 qualification evidence, use the pin-compatible TI LM2903QDRQ1 variant on the same SOIC-8 footprint.

کورتەی بەرهەمە پێشنیارکراوەکان

TL431AIDBZR Texas Instruments بەکارهێنراوە لە: Over-Voltage / Under-Voltage Detection in Power Supplies MC34063ADR DC-DC converter whose output rail is monitored بەکارهێنراوە لە: Over-Voltage / Under-Voltage Detection in Power Supplies TLV431 Low-voltage shunt reference for window thresholds بەکارهێنراوە لە: Window Comparators for Battery Management MC33269DR-5.0 LDO powering the monitoring circuitry بەکارهێنراوە لە: Window Comparators for Battery Management MC14093B CMOS NAND for pulse shaping after comparator بەکارهێنراوە لە: Zero-Crossing and Threshold Detection MOC3021 Triac driver triggered by zero-cross output بەکارهێنراوە لە: Zero-Crossing and Threshold Detection NE555DR Texas Instruments بەکارهێنراوە لە: Oscillators and Pulse/Timing Generators MC14011B CMOS gates for output buffering بەکارهێنراوە لە: Oscillators and Pulse/Timing Generators MC1489NG4 Texas Instruments بەکارهێنراوە لە: Logic-Level Translation and Interface Buffers MC3486NSR Texas Instruments بەکارهێنراوە لە: Logic-Level Translation and Interface Buffers MC33215BE NXP Semiconductors بەکارهێنراوە لە: Automotive and Industrial Sensing Front-Ends LM2903QDRQ1 Texas Instruments بەکارهێنراوە لە: Automotive and Industrial Sensing Front-Ends
What is the supply voltage range of the LM2903DG?
The LM2903DG operates from a single supply of 2V to 36V, or from split supplies of +/-1V to +/-18V. According to the onsemi datasheet, operation is valid as long as the difference between the two supplies is 2V to 36V and VCC is at least 1.5V more positive than the input common-mode voltage. The wide range lets one comparator family cover 5V logic, 12V industrial, and 24V automotive rails.
What is the difference between LM2903DG and LM393?
The LM2903DG and the LM393 share the same die architecture and pinout, but the LM2903 variant is temperature-graded for -40C to +105C operation, while the standard LM393 is graded for commercial 0C to +70C use. Both are dual open-collector comparators with approximately 2 mV input offset and 0.4 mA per-comparator supply current, so the LM2903DG is the industrial/automotive-ambient choice within the same product family.
What is the difference between LM2903DG and TI LM2903DR?
Functionally the LM2903DG (onsemi) and the LM2903DR (Texas Instruments) are the same dual comparator: identical SOIC-8 pinout, open-collector outputs, 2-36V supply range, and -40C to +105C rating. The main differences are the manufacturer, the die revision and guaranteed parameter limits in each datasheet, and supply-chain sourcing. They are widely treated as cross-brand drop-in equivalents on the same PCB footprint.
Does the LM2903DG output need a pull-up resistor?
Yes, the LM2903DG uses open-collector outputs that can only pull low, so each output requires an external pull-up resistor to the desired logic supply. Per the datasheet family description, the output saturates low when the non-inverting input is below the inverting input and floats high through the pull-up otherwise. Pull-up values from 1k to 100k are typical; lower values improve speed and noise immunity but increase current draw.
What is the response time of the LM2903DG?
The typical response time of the LM2903DG is approximately 1.3 us, as listed in comparator cross-reference parameter data for the LM2903 family. This makes it suitable for threshold detection, over-voltage protection, relay driving, and low-to-medium speed timing circuits, but not for fast-edge logic slicing. For nanosecond-class propagation delay, choose a dedicated high-speed comparator instead.
Can the LM2903DG inputs go down to ground in single-supply operation?
Yes, the LM2903DG is designed so the common-mode input voltage range includes ground (the negative rail) during single-supply operation, per the onsemi datasheet. This allows direct sensing of signals referenced to 0V without a negative supply or level-shift circuitry. The only constraint is that VCC must remain at least 1.5V more positive than the input common-mode voltage for specified performance.
Where can I buy LM2903DG online?
LM2903DG is a standard active onsemi part available from authorized distributors. On this page, use the Request a Quote form to obtain current price, stock, and delivery information for the exact SOIC-8 onsemi LM2903DG. Quote requests are answered with lead time and quantity pricing, and volume-break pricing is available for production quantities.
What is the price of the LM2903DG?
The LM2903DG is a commodity dual comparator, so unit pricing depends on order quantity and market availability. For an exact, current quotation rather than a stale list price, submit the Request a Quote form on this page with your required quantity. You will receive quantity-break pricing, currency options, and the current lead time for onsemi LM2903DG in the SOIC-8 (D) package.
What is the lead time for LM2903DG?
Because LM2903DG is a high-volume standard part, distributor stock is usually available for same-day or short-lead-time shipment, with factory orders typically a few weeks. Exact lead time varies with market conditions, so request the current onsemi LM2903DG lead time through the Request a Quote form on this page; the quote will state available stock and delivery date for your quantity.
What is the best drop-in replacement for LM2903DG?
The best drop-in replacements for LM2903DG are pin-compatible SOIC-8 LM2903 devices from other manufacturers: TI LM2903DR (or LM2903DRG4) and the TI LM2903AVQDR precision (A-grade) version are pin-for-pin with the same 2-36V supply range and -40C to +105C temperature rating. Within onsemi, the LM2903DR2G offers the same die in the same SOIC-8 footprint. Verify the offset-voltage grade required by your accuracy budget before switching.
What is the best Texas Instruments equivalent for LM2903DG?
The best Texas Instruments equivalent for the onsemi LM2903DG is the TI LM2903DR in SOIC-8, which is pin-for-pin compatible with the same dual open-collector topology, 2V to 36V supply range, and -40C to +105C ambient rating. TI's LM2903DRG4 is the same die with a reel packing suffix. Both cross to LM2903DG directly in distributor cross-reference tools, requiring no PCB redesign.
Where can I download the LM2903DG datasheet PDF?
Download the LM2903DG datasheet PDF from the onsemi official website product page, where the current revision of the Low Offset Voltage Dual Comparators datasheet (about 10 pages) is published with full electrical characteristics, absolute maximum ratings, and application information. Mirror copies also exist on datasheet aggregators, but the manufacturer site always carries the latest revision with current package drawings.
Where can I find the LM2903DG pinout?
The LM2903DG SOIC-8 pinout is: pin 1 = Output A, pin 2 = Inverting Input A, pin 3 = Non-Inverting Input A, pin 4 = GND/V-, pin 5 = Non-Inverting Input B, pin 6 = Inverting Input B, pin 7 = Output B, pin 8 = VCC/V+. This pinout is common to the entire LM393/LM2903 family across manufacturers, which is why cross-brand SOIC-8 versions are drop-in interchangeable.
Is the LM2903DG suitable for automotive applications?
Yes, with qualification caveats. The standard LM2903DG covers the -40C to +105C ambient range typical of automotive cabin and under-hood-adjacent zones, and its 36V supply rating tolerates 12V/24V automotive rail transients within its absolute maximum limits. However, for formally AEC-Q100 qualified designs, use the automotive-grade variant LM2903QDRQ1 from Texas Instruments, which is pin-compatible in SOIC-8 and carries the Q1 automotive qualification.
What are the key specifications of LM2903DG that engineers should know?
The LM2903DG is a dual differential comparator in SOIC-8 with open-collector outputs, a 2V to 36V single-supply (or +/-1V to +/-18V split-supply) range, typical input offset voltage of 2 mV, typical response time of 1.3 us, about 0.4 mA supply current per comparator, common-mode input range extending to ground, and a -40C to +105C operating range. These figures come from the onsemi LM2903 datasheet family description.
LM2903DG vs LM2903AVQDR - when should I choose each?
Choose the onsemi LM2903DG for general-purpose threshold detection at lowest cost, and choose TI LM2903AVQDR when your application demands tighter guaranteed offset. The A-grade LM2903A version guarantees lower maximum input offset voltage and better offset matching between the two comparators than the standard grade. Both are SOIC-8, pin-for-pin, open-collector, 2-36V devices, so the upgrade requires no footprint change, only a parametric trade-off review.
Is the LM2903DG still active and in production?
Yes, the onsemi LM2903DG is listed as an active, generally available part - distributor listings such as DigiKey show it in stock and shipping. The LM393/LM2903 comparator family has been in continuous production since the 1970s across multiple semiconductor vendors, giving it one of the strongest longevity and multi-source supply records in the analog catalog, which minimizes lifecycle risk for new designs.

داتای سەرچاوەی ئەندازیاری بۆ LM2903DG — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the onsemi LM2903DG when you need the industry-standard dual comparator with an industrial -40C to +105C rating at commodity pricing, and multi-source supply security matters. Choose the onsemi LM393DG if your board never leaves 0C to +70C and you want the lowest-cost grade of the same die. Choose TI LM2903DR or LM2903DRG4 when your AVL prefers TI or when onsemi allocation affects lead time - they are pin-for-pin drop-ins on the same SOIC-8 footprint. Choose TI LM2903AVQDR when guaranteed offset limits matter more than price, such as precision window comparators. For automotive programs requiring AEC-Q100 evidence, choose TI LM2903QDRQ1, also pin-compatible. In every case no PCB redesign is needed; only parametric limits and qualification paperwork differ.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2903DR2G LM393DG LM2903DR LM2903AVQDR LM2903QDRQ1
Package SOIC-8 (D) SOIC-8 - same SOIC-8 - same SOIC-8 - same SOIC-8 - same SOIC-8 - same
Brand onsemi onsemi onsemi Texas Instruments Texas Instruments Texas Instruments
Number of Comparators 2 2 2 2 2 2
Supply Voltage Range 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 32 V class 2 V to 36 V
Output Type Open-collector Open-collector Open-collector Open-collector Rail-to-rail open-collector Open-collector
Operating Temperature Range -40C to +105C -40C to +105C 0C to +70C -40C to +125C -40C to +125C -40C to +125C (Grade 1 class)
Automotive Qualification No (standard industrial grade) No No No No (A-grade precision, not Q1) Yes (AEC-Q100 Q1)

جیاکەرەوە سەرەکییەکان

  • Industrial temperature grade at commodity cost (بەراورد بەLM393DG)
  • Higher maximum ambient ceiling than TI LM2903DR (بەراورد بەLM2903DR)
  • Precision upgrade path without footprint change (بەراورد بەLM2903AVQDR)

تێبینییەکانی دیزاین

Always fit a pull-up resistor on both outputs - the open-collector stage cannot produce a high level on its own, and an unloaded output will appear stuck low. Choose pull-up values between 1k and 100k: lower values improve rise time and noise margin at the cost of sink current; higher values suit battery designs but slow the rising edge and increase susceptibility to capacitive coupling. Never connect the output directly to a supply rail without the resistor, and remember the output high voltage equals the pull-up supply, not VCC.

Add hysteresis whenever the input approaches the threshold slowly or carries noise. A positive-feedback resistor from output to the non-inverting input, sized so that feedback overrides the source impedance by 10x, creates a few-millivolt transfer band that eliminates output chatter. Estimated: with a 100k feedback resistor from a 5V pull-up output and a 10k source impedance, hysteresis is roughly 41 mV - enough to reject typical industrial noise on slowly ramping signals. Un-hysteresized comparators near a threshold can oscillate at high frequency.

Place a 100 nF ceramic decoupling capacitor directly across pins 8 (VCC) and 4 (GND), with a short, wide ground return. Although the LM2903DG draws only about 0.4 mA per comparator, open-collector output switching injects current transients into the ground pin that can disturb the other comparator's reference input in the same package - keep the two threshold divider networks physically separated and reference them to a quiet ground node. Route high-impedance input traces short and guard them with ground to limit leakage-driven offset errors.

Verify the constraint that VCC must remain at least 1.5V more positive than the input common-mode voltage, especially in low-voltage designs: with VCC at 3V, inputs should stay below about 1.5V for specified performance. In split-supply use, keep the total difference between supplies within 2V to 36V. During startup or fault conditions, confirm that input voltages never exceed VCC, since inputs outside the supply rails can cause incorrect output states or damage per the absolute maximum ratings.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The DG suffix indicates onsemi Pb-free, RoHS-compliant SOIC-8 packaging. REACH and halogen-free status should be confirmed from the onsemi product page for the exact ordering code.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2903DG datasheet LM2903DG datasheet pdf LM2903DG pinout LM2903DG equivalent LM2903DG replacement onsemi LM2903DG LM2903DG vs LM2903DR LM2903DG drop-in replacement pin compatible LM2903DG SOIC-8 dual comparator LM2903DG price stock LM2903DG buy LM2903 dual comparator 2-36V open collector LM2903 window comparator circuit LM2903DG cross reference

پێکهاتە و زاراوە پەیوەندیدارەکان

onsemi ON Semiconductor LM2903DG LM2903 LM393 LM2903DR LM2903AVQDR LM2903QDRQ1 Texas Instruments voltage comparator dual differential comparator open-collector output input offset voltage SOIC-8 small outline package surface mount single-supply operation common-mode input range RoHS AEC-Q100 window comparator zero-crossing detection hysteresis pull-up resistor
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ