LM2903DRG4 - Dual 30V Open-Collector Comparator | Texas Instruments
MPN: LM2903DRG4 ✓ چالاکLM2903DRG4 گشتی
The LM2903 is a general-purpose comparator within the broader category of analog comparator ICs. A comparator evaluates two input voltages and produces a logic-level result indicating which input is higher. In an open-collector implementation, the output stage can sink current while remaining in a high-impedance state when the device is inactive. This architecture allows external pull-up resistors to set the output voltage and interface with TTL, MOS, or CMOS logic.
Key characteristics include a 2 V to 30 V supply range for the non-V device, a 30 V maximum supply rating, approximately 1.3 microsecond propagation delay, and typical supply-current drain of approximately 0.4 mA per comparator. The input common-mode range includes ground, and the differential input voltage range is equal to the maximum-rated supply voltage at ±38 V for the versions described by the manufacturer.
The open-collector outputs require pull-up resistors when connected to digital logic. The outputs are intended to sink rather than source output current, so the pull-up resistor value determines the rise time, power consumption, and compatibility with the receiving logic. The wide supply range and low-power operation make the LM2903 suitable for process control, power supervision, sensor conditioning, and general-purpose threshold detection.
When designing around the LM2903, verify the supply limits, common-mode input range, differential input limits, output pull-up network, and the switching behavior required by the downstream circuit. The device is a dual comparator, so each channel is independent, but both channels share the same supply pins and package footprint. The SOIC-8 format supports conventional surface-mount assembly and provides a practical upgrade path from through-hole comparator designs when the pin configuration is verified.
This page brings together the manufacturer product information, verified distributor references, package details, drop-in comparison options, and application guidance for engineers evaluating the LM2903DRG4 in new analog-control and embedded-system designs.
جێگرەوەکانی جێگۆڕکێ بۆ LM2903DRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903DRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Output Type, Propagation Delay, Supply Current, Operating Temperature Range.
LM2903DR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903DT
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2903DG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903BIDR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903-Q1
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2903DRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Dual differential comparator |
| Number of Comparators | 2 |
| جۆری دەرچوون | Open-collector |
| Supply Voltage Range, Single Supply | 2 V to 30 V |
| Maximum Supply Voltage | 30 V |
| Supply Voltage Range, Dual Supply | 2 V to 36 V total supply difference |
| Differential Input Voltage | ±38 V |
| Common-Mode Input Range | Includes ground |
| Propagation Delay | 1.3 us |
| Supply Current Drain | 0.4 mA typical per comparator |
| Output Logic Compatibility | TTL, MOS, and CMOS |
| پاکێج | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Input Pins | 2 differential input pins per comparator |
| Output Pins | 2 open-collector output pins |
| Supply Pins | VCC and ground |
| Automotive Qualification | Not stated in the verified manufacturer information |
ڕێنمایی ڕێکخستنی پینی LM2903DRG4 8-pin soic
ڕێکخستنی پین بۆ LM2903DRG4 (پاکێجی 8-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM2903DRG4.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM2903DRG4 گونجاوە بۆ 6 بەکارھێنانs: Industrial Threshold Detection, Power-Supply Supervision, Sensor Signal Conditioning, Window and Limit Comparators, Motor and Actuator Control Logic, Digital Interface and Logic Conditioning.
Industrial Threshold Detection
The LM2903DRG4 is well suited to industrial threshold detection because it provides two independent differential comparators, a 2 V to 30 V single-supply range, and a common-mode input range that includes ground. Each channel can compare a sensor-derived voltage with a reference level and produce an open-collector status signal for a controller or relay logic. The open-collector output keeps the device compatible with TTL, MOS, and CMOS systems when the pull-up network is selected correctly.
پێشنیارکراو
Power-Supply Supervision
Use the LM2903DRG4 to monitor a supply rail or a divided reference voltage in power-supply supervision circuits. Its differential input arrangement compares the monitored signal with an external reference, while the open-collector output provides a flexible logic-level fault indication. The 30 V maximum supply rating supports higher-voltage supervision than many low-voltage comparator families, subject to the exact input limits and operating conditions.
پێشنیارکراو
Sensor Signal Conditioning
The LM2903DRG4 can convert a slowly changing sensor signal into a digital event when the signal crosses a programmed threshold. For example, a temperature, position, or level sensor can be scaled to the comparator input range and compared against a reference. The approximately 1.3 us propagation delay is suitable for many general-purpose conditioning tasks, while the open-collector output can be pulled up to the voltage required by the next logic block.
پێشنیارکراو
Window and Limit Comparators
Two independent LM2903DRG4 channels can be used together to create a window comparator or upper-and-lower limit detector. One channel can compare the input against a high threshold and the other against a low threshold, with external pull-up resistors and logic combining their outputs. This arrangement is useful in process control, battery-related monitoring, and industrial equipment where an input must remain inside an acceptable range.
پێشنیارکراو
Motor and Actuator Control Logic
The LM2903DRG4 can act as the decision element in low- and medium-voltage motor or actuator control logic by comparing a command signal with a feedback or reference signal. Its open-collector output can be connected to a suitable driver stage through a pull-up resistor, while the 2 V to 30 V supply range accommodates many embedded control rails. The driver, relay, and power-stage ratings must be checked independently of the comparator's output limits.
پێشنیارکراو
Digital Interface and Logic Conditioning
The LM2903DRG4 can convert analog decisions into signals for TTL, MOS, or CMOS logic because its open-collector outputs are identified as compatible with those logic technologies. Place a pull-up resistor from each output to the relevant logic supply and account for the resistor's rise time and power dissipation. The dual-channel arrangement allows two independent decisions to be routed into a control system without adding a second comparator package.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2903DRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2903DR | LM2903DT | LM2903DG4 | LM2903B | LM2903-Q1 |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Single-Supply Operating Range | 2 V to 30 V | 2 V to 30 V | 2 V to 30 V | 2 V to 30 V | 2 V to 30 V | 2 V to 30 V |
| Maximum Supply Voltage | 30 V | 30 V | 30 V | 30 V | 30 V | 30 V |
جیاکەرەوە سەرەکییەکان
- Direct same-family drop-in candidates (بەراورد بەLM2903DR)
- Improved B-version option (بەراورد بەLM2903B)
- Single-supply flexibility (بەراورد بەLM2903DT)
تێبینییەکانی دیزاین
Treat the open-collector output as a sinking element rather than a push-pull driver. Select a pull-up resistor to the logic supply used by the receiving device, and verify that the resulting output-high voltage, output-low sink current, and resistor power are acceptable. A smaller pull-up produces a faster rising edge but increases supply current and dissipation in the pull-up network.
Do not assume that the common-mode input range includes every voltage between the supply rails. The manufacturer information specifically identifies a range that includes ground, while the differential input limit is tied to the maximum-rated supply and is described as ±38 V for the relevant device versions. Verify the exact input-voltage limits and supply combinations in the official LM2903 datasheet before applying large excursions.
Place the LM2903DRG4 close to the compared input nodes and the destination logic to minimize noise pickup and trace delay. Keep the comparator ground connection short and connect the open-collector pull-up resistors near the receiving logic inputs. The 8-pin SOIC footprint requires thermal-relief or via patterns appropriate to the PCB assembly process and the manufacturer's land pattern.
Route the two differential input channels separately when both comparators are active, because shared long traces can allow one channel's switching activity to influence the other. Use a stable reference source and avoid routing input nets parallel to high-current switching paths. Since the outputs are open collector, their rising edges can be slower than the device's internal propagation-delay figure when capacitance and pull-up resistance are significant.
زانیاری پابەندبوون
The verified manufacturer product page identifies the LM2903 family, its supply range, differential input characteristics, output compatibility, and drop-in options. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated for LM2903DRG4 in the verified information. Automotive qualification applies to the separate LM2903-Q1 family option rather than being stated for LM2903DRG4.