LM2904DR2G - Dual 3-32V Op Amp, 8-SOIC | onsemi
MPN: LM2904DR2G ✓ چالاکLM2904DR2G گشتی
An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 belongs to the dual operational amplifier family within the broader operational amplifier, analog IC, and semiconductor hierarchies. Its two channels can amplify two signals independently, or one channel can be used as a buffer while the other performs amplification, filtering, or comparison.
The principal advantages include low power drain, common-mode input operation extending to ground or VEE, and flexible single- or dual-supply configurations. The 3 V minimum supply supports modern low-voltage systems, while the 32 V maximum accommodates higher industrial rails. The -40°C to +105°C operating-temperature range supports applications across consumer, instrumentation, industrial-control, and power-management equipment.
The LM2904 uses a bipolar operational-amplifier architecture. Each channel includes differential inputs and an output stage designed for general-purpose signal conditioning. Unlike rail-to-rail-input devices, its useful input range depends on the selected supply arrangement and common-mode limits. Designers should therefore verify signal levels against the operating conditions in the manufacturer datasheet rather than assuming full rail-to-rail input capability.
Typical applications include low-side current monitoring, sensor-signal conditioning, active filtering, buffer stages, audio preamplification, threshold detection, and general industrial control. It is especially useful when a design requires operation from a single positive supply while processing signals that approach the negative supply rail, which is represented by ground in a single-supply circuit.
For reliable implementation, place the input, feedback, and decoupling components close to their associated pins, use a stable low-noise power source, and check output-current and common-mode limits over the complete temperature range. Bypass capacitors should connect directly to the supply pins to minimize parasitic inductance and preserve stability.
This product page combines the operating characteristics, pin assignments, application guidance, drop-in comparison, and practical layout considerations needed to evaluate the LM2904DR2G for a new analog signal chain.
جێگرەوەکانی جێگۆڕکێ بۆ LM2904DR2G — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2904DR2G (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Common-Mode Input Range, Slew Rate, Amplifier Type, Input Offset Voltage.
LM2904DR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2904DR2G زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Amplifier Channels | 2 channels |
| Supply Voltage Range | 3 V to 32 V |
| مەودای پلەی گەرمیی کارکردن | -40°C to +105°C |
| پاکێج | 8-SOIC |
| جۆری دامەزراندن | Surface mount |
| Supply Configuration | Single supply or split supply |
| Common-Mode Input Range | Extends to ground or VEE |
| Power Consumption | Low power drain |
| Operational Amplifier Architecture | Bipolar |
| Amplifier Type | General purpose |
ڕێکخستنی پینی LM2904DR2G
| پین 1 | OUT1 — Channel 1 output |
| پین 2 | IN1- — Channel 1 inverting input |
| پین 3 | IN1+ — Channel 1 non-inverting input |
| پین 4 | V- — Negative supply connection or ground in single-supply operation |
| پین 5 | IN2+ — Channel 2 non-inverting input |
| پین 6 | IN2- — Channel 2 inverting input |
| پین 7 | OUT2 — Channel 2 output |
| پین 8 | V+ — Positive supply connection |
بەکارهێنانە باوەکان
LM2904DR2G گونجاوە بۆ 6 بەکارھێنانs: Low-Side Current Monitoring, Industrial Sensor Signal Conditioning, Active Audio Filtering, Threshold Detection and Control, Single-Supply Buffering, Power-Supply Control Feedback.
Low-Side Current Monitoring
The LM2904DR2G fits low-side current monitoring because one channel can amplify the small voltage developed across a shunt while the second channel buffers or filters the signal. Its 3 V to 32 V operating range covers low-voltage and industrial systems, and the common-mode input capability extending toward ground or VEE supports shunt signals near the lower rail. The designer must select the shunt value so signal voltage and amplifier input remain within the documented common-mode range, while also checking offset, bias current, output swing, and shunt power at maximum load. A dedicated filtering stage may use the second channel to limit bandwidth and reduce high-frequency noise.
پێشنیارکراو
Industrial Sensor Signal Conditioning
The LM2904DR2G is well suited to conditioning outputs from resistive, capacitive, and other analog sensors in industrial systems. Its dual-channel arrangement allows one amplifier to amplify or buffer the sensor signal and the other to perform active filtering, gain adjustment, or level detection. Operation from 3 V to 32 V supports both compact embedded equipment and higher-voltage industrial interfaces. Because this is a general-purpose amplifier rather than a rail-to-rail precision device, the input level must remain inside the specified common-mode range, particularly in single-supply systems. Offset, input bias current, open-loop gain, bandwidth, and output-swing limits should be evaluated against the sensor source impedance and required accuracy.
پێشنیارکراو
Active Audio Filtering
The LM2904DR2G can implement active low-pass, high-pass, or band-pass sections in audio and communications equipment. Two independent channels provide flexibility for stereo paths or multistage filtering, and the 3 V minimum supply supports compact single-supply designs. The -40°C to +105°C operating range makes the device useful where temperature variation must be considered across industrial or communications equipment. Stable operation depends on feedback-component selection and the amplifier's documented stability behavior, so the filter topology should be checked against the available gain-bandwidth and slew-rate limits. Resistor and capacitor tolerances, output loading, and supply decoupling also determine the achievable gain, bandwidth, and channel-to-channel matching.
پێشنیارکراو
Threshold Detection and Control
The LM2904DR2G can compare a sensor or control signal against a reference and drive a downstream logic or power-control stage. Its two channels allow one amplifier to amplify the incoming signal and the other to compare the result with a threshold, while the 3 V to 32 V supply range accommodates multiple industrial rail arrangements. Common-mode input capability extending toward ground or VEE is useful when the monitored signal lies near the lower supply rail. The comparison accuracy depends on input offset, input bias current, output swing, and reference stability, all of which must be evaluated at the required temperature. Hysteresis may be added with positive feedback to prevent repeated switching around the threshold.
پێشنیارکراو
Single-Supply Buffering
The LM2904DR2G can buffer high-impedance sources in single-supply systems where conventional rail-to-rail-input amplifiers are unnecessary. Buffering reduces source-loading errors and allows the measured node to drive a subsequent filter, measurement stage, or control input. The common-mode input range extending to ground or VEE is particularly valuable when the source signal occupies the lower portion of the available supply range. However, the output cannot be assumed to reach either supply rail, and input and output limitations vary with load and supply voltage. The circuit should therefore be checked for useful input range, output swing, stability, capacitive-load behavior, and the offset introduced by the amplifier itself.
پێشنیارکراو
Power-Supply Control Feedback
The LM2904DR2G can implement error amplification, soft-start shaping, or feedback monitoring in a power-supply control circuit. Its dual channels allow independent comparison and conditioning functions, while the broad 3 V to 32 V supply range supports low-voltage and industrial control environments. For feedback designs, offset and bias current can set the accuracy of the regulated operating point, while slew rate and gain-bandwidth influence loop response. The output must remain within its rated swing during startup and fault conditions, and the common-mode limits must include the full feedback-signal range. Stable compensation and conservative loop-gain margins should be established before increasing the power-stage bandwidth.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2904DR2G — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2904 |
|---|---|---|
| Brand | onsemi | Texas Instruments |
| Package | 8-SOIC | 8-SOIC |
| Number of Channels | 2 channels | 2 channels |
| Supply Voltage Range | 3 V to 32 V | 3 V to 32 V |
| Operating Temperature Range | -40°C to +105°C | -40°C to +105°C |
| Supply Configuration | Single supply or split supply | Single supply or split supply |
| Common-Mode Input Range | Extends to ground or VEE | Extends to ground or VEE |
| Architecture | Bipolar | Bipolar |
| Drop-In Qualification | Reference device | TI documents upgraded drop-in functionality |
جیاکەرەوە سەرەکییەکان
- Broad single- and split-supply operating range (بەراورد بەLM2904)
- Dual general-purpose channels with near-ground common-mode capability (بەراورد بەLM2904)
- Extended industrial temperature coverage (بەراورد بەLM2904)
تێبینییەکانی دیزاین
Do not treat the common-mode input range as rail-to-rail. The useful input range depends on the supply configuration, and its lower boundary can extend toward ground or VEE. Check the complete input and output operating region over the intended supply voltage, temperature, and load. In a 3.3 V single-supply design, verify the actual signal excursion rather than assuming that inputs and outputs can approach either rail.
Place the supply bypass capacitor directly between pins 8 and 4, with a short and low-inductance connection to the package ground or supply-return plane. Keep feedback resistors and inverting-input components close to their associated amplifier pins to minimize parasitic capacitance and feedback-loop area. When both channels operate at different frequencies, maintain separate, short feedback paths so switching activity in one channel does not couple into the other.
Choose closed-loop gain and feedback-component values with the amplifier's documented gain-bandwidth, slew-rate, and stability characteristics in mind. A low-frequency signal path may not require the highest available bandwidth, but excessive gain without corresponding phase-margin analysis can cause ringing or oscillation. Evaluate capacitive loading at the output and use isolation resistors when driving long PCB traces or higher-capacitance downstream nodes.
Estimated: amplifier dissipation is approximately equal to total supply voltage multiplied by the sum of quiescent current and output-current demand, minus output power delivered to the load. For example, using a 12 V supply, 1 mA quiescent current, and a 1 mA load into 5 V gives approximately 12 V × 2 mA - 5 V × 1 mA = 19 mW. Actual junction temperature also depends on package thermal resistance, copper area, and ambient temperature, so verify worst-case operating conditions before increasing output current.
زانیاری پابەندبوون
Material-compliance declarations for the exact ordering code were not identified in the available manufacturer information and should be confirmed with onsemi before formal procurement review.