STMicroelectronics

LM2904DT - Dual 1.1MHz General Purpose Op Amp | STMicroelectronics | SOIC-8

MPN: LM2904DT ✓ چالاک
15 V Vdss SOIC-8 (8-SOIC / SOP-8) Package Internal (no external compensation network) Speed
MOQ: 1 |

LM2904DT گشتی

The STMicroelectronics LM2904DT is a low-power dual general-purpose operational amplifier providing two independent, internally frequency-compensated amplifiers in an 8-pin SOIC (SOP-8) surface-mount package, with a 1.1 MHz unity-gain bandwidth and single-supply operation for automotive and industrial control systems.

An operational amplifier (op amp) is a high-gain differential amplifier that compares an inverting and a non-inverting input and drives its output to amplify the difference between them. When the frequency compensation network is integrated on-chip, the part is called internally compensated and is stable at unity gain without external components. The dual configuration places two independent amplifiers in a single 8-SOIC body, roughly halving the footprint compared with two discrete single amplifiers. In the product hierarchy the device sits as an operational amplifier within analog amplifier ICs and, in turn, within integrated circuits.

Key features include two independent channels in one 8-SOIC package, a 1.1 MHz gain-bandwidth product, internal frequency compensation that removes external compensation parts, a low power supply drain that is independent of the magnitude of the output voltage swing, and single-supply operation over a wide voltage range. The LM2904 family was designed specifically for automotive and industrial control systems, so robustness and supply-voltage tolerance matter more than precision offset or ultra-low noise.

Internally the device uses a classic internally compensated bipolar input stage with single-ended outputs. Both amplifiers share one supply rail and one ground reference, so bypass and grounding rules apply to the whole package: place a small ceramic capacitor adjacent to the supply pin and add local bulk decoupling near the pins. Output swing is not rail-to-rail, so the load must be chosen so the output stays inside the supply range, and the input common-mode range must be respected when signals approach the rails.

Typical uses include motor and solenoid feedback loops in automotive electronic control units, industrial sensor signal conditioning, bridge and transducer amplification, low-side current sensing, and general DC buffering inside PLC and instrumentation racks. Two independent channels in one package also serve a control loop and a monitoring channel together.

One design tip: keep feedback routing short, guard high-impedance input nodes against pickup, and decouple the supply at the package. Do not select this amplifier where rail-to-rail input or output, very low noise, or micro-power operation is required; choose a precision or CMOS-input amplifier family instead.

This page combines the manufacturer specification summary, a complete pin map for the SOIC-8 footprint, drop-in alternatives with quantified parameter differences, and practical power, layout, and signal-integrity notes that are not combined in a single manufacturer document.

جێگرەوەکانی جێگۆڕکێ بۆ LM2904DT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2904DT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Gain-Bandwidth Product, Number of Amplifiers, Number of Channels.

STMicroelectronics
Package: 14-pin SOIC
Amplifier Type: Quad general-purpose bipolar operational amplifier
Gain-Bandwidth Product: 1.3 MHz
بەراوردکردن لەگەڵ LM2904DT →
Texas Instruments
Package: 8-SOIC (D)
Amplifier Type: General Purpose
بەراوردکردن لەگەڵ LM2904DT →
Texas Instruments
Package: 8-SOIC (D)
Amplifier Type: General Purpose
بەراوردکردن لەگەڵ LM2904DT →
Texas Instruments
Package: 8-TSSOP, 4.40 mm width
Gain-Bandwidth Product: 700 kHz
Number of Amplifiers: 2 circuits
بەراوردکردن لەگەڵ LM2904DT →
Texas Instruments
Package: 8-TSSOP, 4.40 mm width
Gain-Bandwidth Product: 700 kHz
Number of Amplifiers: 2 circuits
بەراوردکردن لەگەڵ LM2904DT →
Texas Instruments
Package: 8-SOIC (DBV), 0.154 in (3.90 mm) width
Amplifier Type: General Purpose, single-supply
بەراوردکردن لەگەڵ LM2904DT →
STMicroelectronics
Package: 8-SOIC
Number of Amplifiers: 2 circuits
بەراوردکردن لەگەڵ LM2904DT →
STMicroelectronics
Package: 8-SOIC, 3.90 mm body width
Amplifier Type: Dual general-purpose operational amplifier
Number of Channels: 2 channels
بەراوردکردن لەگەڵ LM2904DT →

LM2904D

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904DT

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 SOIC-8 (8-SOP-J)
2 · 2 · Standard (General Purpose) · Single-Ended · High gain, internally frequency-compensated · 1.1 MHz · 15 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904DR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

NJM2904D

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-8
Pin-to-pin 8-SOIC dual general-purpose amplifier; offset and bias current grades differ, bandwidth in the same 1 MHz class

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM248DT

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 SOIC-8
Quad general-purpose bipolar operational amplifier · 4 circuits · 1.3 MHz · 0.5 V/µs · 0.53 mA · 1 mV maximum · 2 nA maximum · 30 nA maximum

✓ بەردەستە

$0.9516 / یەکە

بینینی داتاشیت →

LM2904DT زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Amplifiers 2
Number of Channels 2
Amplifier Type Standard (General Purpose)
جۆری دەرچوون Single-Ended
Gain High gain, internally frequency-compensated
Gain-Bandwidth Product 1.1 MHz
Operating Voltage (listing designation) 15 V
Supply Type Single supply
Power Supply Drain Low, independent of output voltage swing magnitude
Frequency Compensation Internal (no external compensation network)
پاکێج SOIC-8 (8-SOIC / SOP-8)
ژمارەی پین 8
جۆری دامەزراندن Surface Mount
Target Applications Automotive and industrial control systems

ڕێکخستنی پینی LM2904DT

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 OUT A — Output of amplifier A (single-ended)
پین 2 IN- A — Inverting input of amplifier A
پین 3 IN+ A — Non-inverting input of amplifier A
پین 4 V- — Negative supply / ground reference
پین 5 IN+ B — Non-inverting input of amplifier B
پین 6 IN- B — Inverting input of amplifier B
پین 7 OUT B — Output of amplifier B (single-ended)
پین 8 V+ — Positive supply input

بەکارهێنانە باوەکان

LM2904DT گونجاوە بۆ 6 بەکارھێنانs: Automotive Motor Control Feedback, Industrial Sensor Signal Conditioning, Low-Side Current Sensing, Power Supply Feedback and Regulation, Audio and Communication Line Stages, Instrumentation and Test Equipment.

🚗

Automotive Motor Control Feedback

The LM2904DT fits ECU feedback loops where the amplifier conditions a scaled motor or solenoid current signal before it reaches an ADC. Its 1.1 MHz gain-bandwidth product leaves enough loop bandwidth to follow a PWM-controlled actuator edge while its low power supply drain, which is independent of output voltage swing magnitude, keeps the quiescent load predictable across the duty cycle. Because the device was designed for automotive and industrial control systems and tolerates a single supply over a wide voltage range, it handles 12-V style rails without an extra boost stage. Two independent channels in one SOIC-8 let one package handle the control loop and a redundant monitoring path. The single-ended output drives the ADC input directly through a simple RC filter, avoiding an extra buffer.

🏭

Industrial Sensor Signal Conditioning

In PLC and instrumentation racks the LM2904DT is used to buffer and amplify transducer outputs such as thermocouple, strain-gauge, and resistive sensor signals before conversion. The dual channel lets a single SOIC-8 amplify one sensor leg while the second channel provides the reference or gain stage for the same front end. A 1.1 MHz gain-bandwidth product comfortably handles 50/60 Hz and kHz-range process signals, and internal frequency compensation removes the external C1 element that a discrete design would need. Its low supply drain and single-supply operation simplify the 24-V-to-low-voltage rail architecture in the field. The part is not precision grade, so for millivolt-level bridges with tight error budgets an instrumentation amplifier is a better match.

⚡

Low-Side Current Sensing

The LM2904DT is widely used in shunt-based current sensing because its single-ended output drives the ADC or comparator input directly from a low-ohm shunt in the ground return path. The 1.1 MHz gain-bandwidth product provides more than enough bandwidth for the measurement amplifier while keeping the shunt system stable with standard feedback networks. Its low supply drain, which does not increase with output swing, means the sensing amplifier adds almost no overhead to the overall system power budget - important in battery-backed or automotive auxiliary rails. Two channels allow simultaneous measurement of two rails or an averaged differential pair. Because input bias current and offset are not precision grade, the accuracy limit comes from the shunt and the ADC rather than from the amplifier itself.

🔧

Power Supply Feedback and Regulation

The LM2904DT serves in linear power supply designs as the error amplifier in voltage-mode feedback, comparing a scaled output against a reference and driving the pass device. Its wide single-supply operating range and low power supply drain are valuable in multi-output industrial supplies where an auxiliary rail must be generated without adding load to the main converter. Internal frequency compensation stabilizes the loop with a simple compensation capacitor, and the 1.1 MHz bandwidth keeps loop crossover well above the switching ripple frequency of an upstream stage. Because the part is bipolar-input and not rail-to-rail, the feedback node must stay inside the input common-mode range and the output must not be driven into saturation. Verify loop stability against the pass device and output capacitor in simulation.

🎧

Audio and Communication Line Stages

The LM2904DT is used as a line-level buffer and gain stage in low-frequency audio, intercom, and communication equipment where a general-purpose dual amplifier is adequate. Its 1.1 MHz gain-bandwidth product supports audio-band pass-through with margin for small-signal overshoot, and the dual configuration handles two channels of a stereo or balanced pair in one package. Internal frequency compensation allows inverting and non-inverting gain configurations to be built directly from the pinout shown on this page. The trade-off is that input bias current and offset are not audio-grade low values, so very high source impedances or DC-coupled microphone inputs favor a CMOS-input amplifier. For microphone preamplifiers with very low noise requirements, use a dedicated low-noise family instead.

🖥️

Instrumentation and Test Equipment

The LM2904DT appears in bench instruments and automated test fixtures as a buffer for mid-impedance sources such as dividers, probes, and DAC outputs. Its low supply drain and single-rail flexibility make it convenient to run from a 5-V or 12-V instrument rail without an additional level shifter, while the 1.1 MHz bandwidth comfortably handles measurement bandwidths up to hundreds of kHz. Two channels allow a reference buffer and a measurement buffer to share one package close to the connector, reducing parasitic pickup on high-impedance nodes. The single-ended output stage is adequate for driving ADC front ends and comparators, but output swing is not rail-to-rail, so bias the signal chain around mid-supply to maximise usable range. For 16-bit-plus resolution paths, check the offset and bias current contribution against the ADC input-referred error budget.

What is the LM2904DT and what does it do?
The LM2904DT is a low-power dual general-purpose operational amplifier from STMicroelectronics containing two independent, high-gain, internally frequency-compensated amplifiers in an 8-pin SOIC (SOP-8) package. According to the STMicroelectronics LM2904 datasheet, the circuit operates from a single power supply over a wide range of voltages and was designed for automotive and industrial control systems. Each channel amplifies the difference between its inverting and non-inverting inputs, with a gain-bandwidth product of 1.1 MHz.
What are the key specifications of LM2904DT that engineers should know?
The LM2904DT provides two amplifier channels, single-ended outputs, a 1.1 MHz gain-bandwidth product, internal frequency compensation, and single-supply operation from a single positive rail. The STMicroelectronics datasheet states that the low power supply drain is independent of the magnitude of the output voltage swing. The device is supplied in the surface-mount SOIC-8 package, and both channels share one supply and ground reference, so one bypass network serves the whole device.
Where can I download the LM2904DT datasheet PDF?
The authoritative LM2904DT datasheet PDF is published by STMicroelectronics at https://www.st.com/resource/en/datasheet/lm2904.pdf, covering the LM2904, LM2904A, LM2904W and LM2904AW family including package information. The STMicroelectronics product page for LM2904 at st.com provides ordering, lifecycle, and support information. Use the manufacturer document for pin assignments, absolute maximum ratings, electrical characteristics, and typical performance curves.
Where do I find the LM2904DT pinout?
The LM2904DT pinout is shown in the pin-assignment table of the STMicroelectronics LM2904 datasheet and matches the standard 8-SOIC dual op-amp footprint: pin 1 = output A, pin 2 = inverting input A, pin 3 = non-inverting input A, pin 4 = V-, pin 5 = non-inverting input B, pin 6 = inverting input B, pin 7 = output B, pin 8 = V+. The SOIC-8 package drawing is on this page for direct comparison with the manufacturer diagram.
Is the LM2904DT pin compatible with the LM2904D and other LM2904 variants?
Yes. The LM2904D from STMicroelectronics uses the same 8-SOIC pin arrangement and the same electrical function, so it is a direct drop-in substitute for the LM2904DT when the tape-and-reel suffix of the ordering code is the only difference. The cross-reference listings for LM2904 and LM2904D identify pin-to-pin replacement parts across STMicroelectronics, National Semiconductor, NJRC, Philips, and Toshiba, confirming that the 8-pin footprint is industry standard.
LM2904DT vs LM2904DR from Texas Instruments - which should I choose?
The STMicroelectronics LM2904DT is specified at 1.1 MHz gain-bandwidth product, while the Texas Instruments LM2904DR is listed as a dual 26-V, 700-kHz operational amplifier in the same 8-SOIC package with identical pinout. The ST part therefore offers roughly 57 percent more bandwidth, while the TI part carries a lower maximum supply rating of 26 V. Choose the LM2904DT when signal speed or supply headroom matters; the TI part is acceptable for lower-bandwidth, lower-voltage designs.
What can replace the LM2904DT?
The most direct replacements are the STMicroelectronics LM2904D and the ROHM Semiconductor LM2904DT, both of which use the identical 8-pin SOIC pinout and the same dual general-purpose amplifier function, so no PCB change is needed. Other pin-to-pin options include the Texas Instruments LM2904DR (lower 700 kHz bandwidth) and the Renesas NJM2904D. Always confirm supply-voltage range, output swing, and temperature grade against the manufacturer datasheet before substituting.
Is the ROHM Semiconductor LM2904DT a drop-in for the STMicroelectronics LM2904DT?
The ROHM Semiconductor LM2904DT is listed as a standard general-purpose dual amplifier in an 8-SOP-J package, which is the same SOIC-8 outline and pin arrangement used by the STMicroelectronics version, making it a drop-in replacement on the same footprint. Key differences to confirm are the input offset voltage grade, temperature range, and qualification status, which vary between manufacturers for this classic dual op-amp family.
When should I choose the LM2904DT over the LM2904DR?
Choose the LM2904DT when you need more gain-bandwidth product or more supply headroom than the Texas Instruments LM2904DR provides, since 1.1 MHz versus 700 kHz is a 57 percent bandwidth increase for the same 8-SOIC footprint and pinout. Choose the LM2904DR when its 26-V maximum supply rating is sufficient and its broader sourcing base is preferred. Because the pinouts match, the decision is purely parametric and never requires a board change.
Is the LM2904DT suitable for automotive applications?
Yes. The STMicroelectronics LM2904 datasheet describes the circuit as two independent, high-gain, internally frequency-compensated operational amplifiers designed specifically for automotive and industrial control systems, operating from a single supply over a wide voltage range with low supply drain independent of output swing. For a specific vehicle program, verify the temperature grade and automotive qualification of the exact ordering code with the manufacturer before release.
How should I decouple and lay out the LM2904DT on a PCB?
Place a small ceramic bypass capacitor, typically 100 nF, directly across the supply pin (pin 8) and ground (pin 4) of the SOIC-8 package, and add local bulk decoupling near the pins for longer supply traces. Route feedback components close to pins 2, 3, 6 and 7 to minimize parasitic capacitance in the compensation loop. Because both channels share one rail, bypassing the package once benefits both amplifiers, and grounding should follow a single-point return path back to the supply.
What are the trade-offs of using the LM2904DT instead of a precision amplifier?
The LM2904DT optimizes for low cost, low power supply drain, wide supply tolerance, and a 1.1 MHz bandwidth rather than for accuracy. Offset voltage, input bias current, drift, and noise are not precision-grade, and neither input nor output swings rail-to-rail. If your signal chain needs low offset, low bias current for high source impedance, or rail-to-rail operation, choose a precision or CMOS-input amplifier family instead of this general-purpose part.
What is the lead time and stock status for the LM2904DT?
The LM2904DT is a long-lived, in-demand dual op amp from STMicroelectronics, and multiple authorized channels list the part for order with full standard ordering information on the manufacturer product page. Current stock position, minimum order quantity, and lead time change frequently, so request the latest figures using the Request a Quote form on this page rather than relying on a cached figure.
Where can I buy the LM2904DT online?
The LM2904DT is available from STMicroelectronics authorized distributors and from XAIPART, which stocks the part in the standard SOIC-8 surface-mount package. Use the Request a Quote form on this page to obtain current pricing, stock, and lead time for the exact ordering code. For full technical confirmation, refer to the STMicroelectronics LM2904 datasheet and product page links listed in the data sources section.
Can the LM2904DT drive a load directly?
The LM2904DT uses a single-ended output stage, so the output current capability and drive strength are limited compared with a rail-to-rail CMOS-input amplifier. It is suitable for high-impedance loads and standard feedback networks, but it is not intended for driving low-ohmic or capacitive loads directly. Confirm output current and output swing limits in the manufacturer electrical characteristics table, and use a buffer stage if heavier loading is expected.
What does the LM2904DT datasheet say about power supply drain?
The STMicroelectronics LM2904 datasheet states that the low power supply drain of the device is independent of the magnitude of the output voltage swing. This is a key architectural benefit of the internal design, because supply current stays roughly constant whether the output sits near mid-rail or swings close to the rails, simplifying thermal and battery-budget calculations in portable and automotive control modules. Operating temperature and quiescent current figures are given in the manufacturer electrical characteristics table.
What is the difference between LM2904 and LM2904A?
The STMicroelectronics datasheet covers LM2904, LM2904A, LM2904W and LM2904AW as variants of the same low-power dual operational amplifier family, with different offset voltage and temperature grade options while retaining the same 8-SOIC dual-channel architecture and internal compensation. The A-suffix grade is the tighter-offset version for applications that need better DC accuracy at the same bandwidth class. Choose the grade whose offset, drift, and temperature limits match your error budget.

داتای سەرچاوەی ئەندازیاری بۆ LM2904DT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM2904DT when you need two independent general-purpose amplifiers in one 8-SOIC package for automotive or industrial control, sensor conditioning, or low-side current sensing, especially where a single supply with wide tolerance is available and the signal bandwidth stays below a few hundred kHz. Choose the LM2904D from the same manufacturer when the ordering code rather than the electrical specification is the deciding factor, and choose the ROHM Semiconductor LM2904DT or Renesas NJM2904D when you want an alternative source on the same footprint. Pick the Texas Instruments LM2904DR only if its 700 kHz bandwidth and 26-V supply ceiling are sufficient and a broader sourcing base matters more than speed. Use the LM248DT when offset voltage and drift accuracy matter more than bandwidth, and move to a CMOS-input amplifier such as the MCP6001 family when the source impedance is high, the rail-to-rail swing is required, or the supply current budget is tight.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2904D LM2904DT LM2904DR NJM2904D LM248DT
Package SOIC-8 SOIC-8 - same SOIC-8 (8-SOP-J) - same SOIC-8 - same SOIC-8 - same SOIC-8 - same
Brand STMicroelectronics STMicroelectronics ROHM Semiconductor Texas Instruments Renesas Electronics Texas Instruments
Number of Amplifiers 2 2 2 2 2 2
Amplifier Type Standard (General Purpose) Standard (General Purpose) Standard (General Purpose) Standard (General Purpose) General Purpose dual Precision dual
Output Type Single-Ended Single-Ended Single-Ended Single-Ended Single-Ended Single-Ended
Frequency Compensation Internal Internal Internal Internal Internal Internal
Target Application Automotive and industrial control systems Automotive and industrial control systems General purpose signal conditioning General purpose, wide supply range General purpose Precision instrumentation
Special Feature Low supply drain independent of output voltage swing Same low supply drain behaviour Same low supply drain behaviour Internal compensation, low-power operation Internal compensation Low offset and low drift

جیاکەرەوە سەرەکییەکان

  • Higher gain-bandwidth product than the closest TI general-purpose equivalent (بەراورد بەLM2904DR)
  • Tighter power budget from low supply drain independent of output swing (بەراورد بەLM248DT)
  • Drop-in sourcing across multiple manufacturers for the same 8-SOIC footprint (بەراورد بەNJM2904D)

تێبینییەکانی دیزاین

Both amplifiers share one supply rail, so a single bypass network serves the whole package. Place a 100 nF ceramic capacitor directly across pin 8 (V+) and pin 4 (V-) with the shortest possible trace, and add a bulk capacitor nearby if the supply trace is long or shared with switching nodes. Estimated: with a 1.2 mA total quiescent current at 15 V supply, the regulator-side static dissipation is about 18 mW, so the dominant thermal path is not the IC but the surrounding power stage. Keep the analog ground return separate from high-current switching returns.

Route both feedback networks (pins 2, 3, 6, 7) on the top copper layer with the resistor and capacitor network directly adjacent to the package pins, and avoid running the inverting input node underneath or beside the supply and output pins. Keep the ground pin 4 connection short and use a solid ground plane on the layer opposite the components. Because the device is internally compensated and unity-gain stable, no external compensation network is required, but parasitic capacitance added to the inverting node can still cause ringing, so keep that node as small as possible.

Do not assume rail-to-rail behaviour. The bipolar input stage and single-ended output mean the usable input common-mode range and output swing are narrower than the supply rails, so bias inverting amplifier inputs near mid-supply to maximise signal range. Also avoid driving the output into a low-impedance or capacitive load, and never let the supply exceed the absolute maximum rating given in the manufacturer datasheet. For high-impedance sources, remember that input bias current of a bipolar amplifier can create DC error across the source impedance - a CMOS-input amplifier is preferable there.

When the amplifier sits directly in front of an ADC, add an RC anti-alias filter at the output pin with a corner frequency well below the converter sample rate, and check that the ADC input sampling capacitor can be driven by the amplifier output without stability complaints - add a small isolation resistor if the datasheet allows. At 1.1 MHz the part is fast enough to amplify switching edges, so keep the amplifier away from digital clocks and relay drivers. For 50/60 Hz rejection in instrumentation, prefer differential topology over a single-ended stage.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The LM2904DT is documented by STMicroelectronics as a dual general-purpose operational amplifier for automotive and industrial control systems. Explicit RoHS, REACH, halogen-free and conflict-minerals statements are not published on the retrieved product listings, so these fields are left as unknown; obtain the material declaration from the manufacturer for a specific ordering code.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm2904dt datasheet LM2904DT pinout LM2904DT SOIC-8 amplifier LM2904DT STMicroelectronics LM2904DT dual op amp 1.1MHz LM2904DT equivalent LM2904DT replacement LM2904DT drop-in substitute SOIC-8 LM2904DT vs LM2904DR LM2904DT price LM2904DT stock and lead time LM2904 application circuit LM2904 low power dual operational amplifier dual general purpose op amp 8-SOIC 1MHz

پێکهاتە و زاراوە پەیوەندیدارەکان

STMicroelectronics LM2904DT LM2904D LM2904 LM2904A ROHM Semiconductor Texas Instruments LM2904DR Renesas Electronics NJM2904D LM248DT operational amplifier op amp dual amplifier internally frequency-compensated single-ended output single-supply operation gain-bandwidth product unity-gain bandwidth SOIC-8 SOP-8 surface mount SMD package automotive control system industrial control system signal conditioning low-side current sensing amplifier IC integrated circuit
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ