Texas Instruments

LM2904QDRG4Q1 - Dual 26 V AEC-Q100 Op Amp, 700 kHz, SOIC-8 | Texas Instruments

MPN: LM2904QDRG4Q1 ✓ چالاک
3 V to 26 V Vdss 0.7 mA typical Id 8-SOIC (DBV), 0.154 in (3.90 mm) width Package
MOQ: 1 |

LM2904QDRG4Q1 گشتی

The Texas Instruments LM2904QDRG4Q1 is an automotive-grade dual operational amplifier with two independent, internally compensated amplifiers packaged in an 8-pin SOIC (DBV) package. Each channel delivers a 700 kHz gain-bandwidth product, a 0.3 V/us slew rate, and operates from a single supply between 3 V and 26 V.

What is a dual operational amplifier? A dual op amp is a single integrated circuit containing two independent, high-gain, frequency-compensated amplifiers. It belongs to the hierarchy: operational amplifier -> analog amplifier IC -> integrated circuit -> semiconductor. The LM2904-Q1 family is the AEC-Q100-qualified automotive version of the industry-standard LM2904, which is one of the most widely cloned and second-sourced general-purpose amplifier footprints in the world.

Key electrical features include a low supply-current drain that is independent of supply voltage (0.7 mA typical per amplifier), a common-mode input voltage range that includes ground, and a common-mode rejection ratio of 65 dB. Because the amplifiers are internally compensated, no external frequency-compensation network is required, which simplifies both PCB layout and BOM cost in automotive designs.

Internally, each amplifier uses a differential input stage with a class-A output stage that provides good output swing and load-driving capability. The single-supply operation from 3 V to 26 V directly accommodates 12 V battery-derived automotive rails with transient margin, and allows the same part to be used across 5 V, 12 V and 24 V nominal systems without a second part number.

Typical automotive applications include body electronics modules, actuator and relay drivers, sensor signal conditioning for resistive sensors, battery monitoring, and low-cost power supply feedback. The same amplifier is equally suited to industrial instrumentation, audio preamplifier stages, and general DC signal conditioning where a cost-optimized general-purpose dual amplifier is preferred over a precision rail-to-rail part.

When designing with the LM2904QDRG4Q1, remember that it is a bipolar general-purpose amplifier with input common-mode range that does not reach the positive rail. Place a supply-bypass capacitor of 0.1 uF close to pin 8 and a bulk capacitor near pin 4, and use resistors of 10 kohm or lower in the feedback network to preserve bandwidth.

This page consolidates manufacturer specifications, AEC-Q100 qualification details, drop-in SOIC-8 alternatives from Texas Instruments and STMicroelectronics, and practical layout guidance that is not collected in one place on a distributor listing.

جێگرەوەکانی جێگۆڕکێ بۆ LM2904QDRG4Q1 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2904QDRG4Q1 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Package, Gain-Bandwidth Product, Mounting Type, Compensation.

STMicroelectronics
Amplifier Type: Standard (General Purpose)
Package: SOIC-8 (8-SOIC / SOP-8)
Gain-Bandwidth Product: 1.1 MHz
بەراوردکردن لەگەڵ LM2904QDRG4Q1 →
Texas Instruments
Amplifier Type: Dual general-purpose operational amplifier
Gain-Bandwidth Product: 700 kHz
بەراوردکردن لەگەڵ LM2904QDRG4Q1 →
Texas Instruments
Package: 8-SOIC, 3.90 mm body width
Gain-Bandwidth Product: 700 kHz per channel
Compensation: Internally frequency compensated
بەراوردکردن لەگەڵ LM2904QDRG4Q1 →
STMicroelectronics
Amplifier Type: General-purpose operational amplifier
Package: 8-pin MiniSO
Mounting Type: Surface-mount
بەراوردکردن لەگەڵ LM2904QDRG4Q1 →

LM2904BQDRG4Q1

✅ جێگرەوەی ڕاستەوخۆ
📦 8-SOIC (DBV)
same 8-SOIC pinout and 700 kHz class performance, but maximum supply voltage raised to 36 V (+38% versus 26 V); AEC-Q100 qualified

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2904BAQDRG4Q1

✅ جێگرەوەی ڕاستەوخۆ
📦 8-SOIC (DBV)
same 8-SOIC pinout, AEC-Q100 qualified next-generation LM2904BA-Q1 with 36 V maximum supply voltage (+38% versus 26 V) and updated offset/CMRR characteristics

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2904QD

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-SOIC (DBV)
Dual general-purpose operational amplifier · 2 channels · 26 V · 700 kHz · Automotive · SOP · 8 terminals · Gull wing

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904DT

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 8-SOIC (DBV)
2 · 2 · Standard (General Purpose) · Single-Ended · High gain, internally frequency-compensated · 1.1 MHz · 15 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904ST

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 8-SOIC (DBV)
General-purpose operational amplifier · 2 channels · 2 amplifiers · Two independent, internally frequency-compensated amplifiers · Single-ended · Low-power operational amplifier · 8-pin MiniSO · Surface-mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904QDRG4Q1 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Type General Purpose, single-supply
Number of Circuits 2 (independent channels)
Supply Voltage Range 3 V to 26 V
Maximum Supply Voltage 26 V
Gain Bandwidth Product 700 kHz
Slew Rate 0.3 V/us
Supply Current (per amplifier) 0.7 mA typical
Common-Mode Rejection Ratio (CMRR) 65 dB
Automotive Qualification AEC-Q100 qualified
پاکێج 8-SOIC (DBV), 0.154 in (3.90 mm) width
Packaging Tape and Reel (TR)
جۆری دامەزراندن Surface Mount
ژمارەی پینەکان 8
Compensation Internal (internally compensated)
Shutdown / Enable None (no shutdown pin)
دۆخی RoHS Compliant

ڕێکخستنی پینی LM2904QDRG4Q1

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 OUT1 — Amplifier 1 output
پین 2 IN1- — Inverting input of amplifier 1
پین 3 IN1+ — Non-inverting input of amplifier 1
پین 4 V- — Negative supply / ground
پین 5 IN2+ — Non-inverting input of amplifier 2
پین 6 IN2- — Inverting input of amplifier 2
پین 7 OUT2 — Amplifier 2 output
پین 8 V+ — Positive supply

بەکارهێنانە باوەکان

LM2904QDRG4Q1 گونجاوە بۆ 6 بەکارھێنانs: Automotive Body Electronics and Actuator Drivers, Automotive Sensor Signal Conditioning, Battery Monitoring and Current Sense Amplification, Audio Preamplifier and Headphone Drive Stages, Industrial Instrumentation and 4-20 mA Loop Buffering, Relay, Solenoid and Lamp Load Driver.

🚗

Automotive Body Electronics and Actuator Drivers

The LM2904QDRG4Q1 fits 12 V battery-derived body modules where AEC-Q100 qualification and single-supply operation from 3 V to 26 V are required. Its two independent channels are typically used as a non-inverting gain stage followed by a power buffer driving a relay, solenoid or lamp driver MOSFET gate, which removes the need for two discrete amplifiers. The 0.7 mA typical supply-current drain that is largely independent of supply voltage limits quiescent load on the vehicle quiescent-current budget. Because the amplifiers are internally compensated, no external compensation network is needed, keeping the 8-SOIC footprint small. Verify transient margin against your raw-bus load dump profile and keep the input common-mode range in mind on 5 V-regulated sub-rails.

🌡️

Automotive Sensor Signal Conditioning

For resistive and resistive-divider sensors in body or powertrain modules, the LM2904QDRG4Q1 provides the gain stage and buffer in an 8-SOIC package. One channel can amplify a thermistor or RTD bridge output while the other buffers the reference or drives the excitation, keeping the signal chain short and the board area minimal. The 65 dB CMRR limits differential pickup from adjacent harness wiring, an important factor in long cable runs inside a vehicle body. The amplifier's single-supply range from 3 V to 26 V permits direct connection to protected battery rails after input clamping. Choose precision resistor networks and validate input bias current effects against your sensor impedance before finalising the gain error budget.

⚡

Battery Monitoring and Current Sense Amplification

The LM2904QDRG4Q1 is widely used in battery-management sub-circuits to buffer a resistive shunt output and to amplify a scaled pack-voltage divider. Its 26 V maximum supply tolerates pack voltages above the 12 V nominal system rail, and the low, supply-independent supply-current drain keeps parasitic draw acceptable in parked vehicles. One channel typically buffers the high-side divider for the pack monitor while the other provides gain on a low-side shunt amplifier. The 0.3 V/us slew rate is more than adequate for kHz-bandwidth current signals. Check the input common-mode range against your shunt reference point, since a bipolar general-purpose amplifier cannot swing to its positive rail.

🎧

Audio Preamplifier and Headphone Drive Stages

In low-cost audio modules the LM2904QDRG4Q1 serves as a dual microphone preamplifier or line-level input stage, delivering 700 kHz gain-bandwidth and 0.3 V/us slew rate for signals well into the audio band. Its dual-channel architecture means one package handles left and right channels, cutting board area in a stereo head unit or intercom. The low supply-current drain keeps quiescent power acceptable in battery-powered speakers, and the common-mode range that includes ground suits single-supply coupling from a biased source. Trade-off: a bipolar general-purpose part has higher distortion than a dedicated audio amplifier and no rail-to-rail output swing, so keep output levels below the upper rail and add an output coupling capacitor if biasing on a single supply.

🏭

Industrial Instrumentation and 4-20 mA Loop Buffering

The LM2904QDRG4Q1 works well as the output buffer and active filter element in industrial transmitter and loop-isolator designs. Two channels can implement a two-pole Sallen-Key low-pass filter on the 4-20 mA current signal, while internal compensation and the 700 kHz gain-bandwidth product give ample loop margin for slow process-control loops. Its 3 V to 26 V supply range covers both 24 V loop power and lower-voltage sensor interfaces with one part number. The low supply-current drain matters where several channels share a tightly budgeted loop power budget. Because the input common-mode range does not include the positive rail, the buffer must be biased appropriately, and the output stage requires headroom for its saturation voltage when driving the 200-ohm loop load.

🔧

Relay, Solenoid and Lamp Load Driver

The LM2904QDRG4Q1 is frequently used to drive an N-channel MOSFET gate in relay, solenoid and indicator lamp circuits where the amplifier supplies the gate drive current and level shift from a low-voltage logic domain to a higher-voltage coil. With 0.3 V/us slew rate, gate transitions stay short enough to limit switching loss and EMI generation, and the 26 V supply rating tolerates coil transients when combined with a clamp. The internal compensation means feedback networks can be set for gain without an external compensation capacitor, simplifying the loop design. Keep the input common-mode range in mind when the logic signal sits near the positive rail, and provide bulk decoupling close to pin 8 to keep supply noise off the gate drive path.

کورتەی بەرهەمە پێشنیارکراوەکان

LM2904QD Texas Instruments بەکارهێنراوە لە: Automotive Body Electronics and Actuator Drivers, Automotive Sensor Signal Conditioning, Battery Monitoring and Current Sense Amplification, Industrial Instrumentation and 4-20 mA Loop Buffering, Relay, Solenoid and Lamp Load Driver TLV9062IDR low-power dual op amp for low-current modules بەکارهێنراوە لە: Automotive Body Electronics and Actuator Drivers, Audio Preamplifier and Headphone Drive Stages, Relay, Solenoid and Lamp Load Driver OPA2196 precision dual alternative for higher accuracy rails بەکارهێنراوە لە: Automotive Body Electronics and Actuator Drivers, Automotive Sensor Signal Conditioning, Audio Preamplifier and Headphone Drive Stages, Industrial Instrumentation and 4-20 mA Loop Buffering MCP6002 rail-to-rail dual for low-voltage shunt measurement بەکارهێنراوە لە: Battery Monitoring and Current Sense Amplification
What is the LM2904QDRG4Q1?
The LM2904QDRG4Q1 is a Texas Instruments dual, general-purpose operational amplifier qualified for automotive applications to AEC-Q100. It contains two independent, internally compensated amplifiers in an 8-pin SOIC (DBV) package. According to the TI LM2904-Q1 product page, the device is the automotive-qualified member of the industry-standard LM2904 family, specified for a 26 V maximum supply and a 700 kHz gain-bandwidth product, with tape-and-reel packaging for automated assembly.
What is the supply voltage range of LM2904QDRG4Q1?
The LM2904QDRG4Q1 operates from a single supply of 3 V to 26 V. The TI LM2904-Q1 product page describes the family as a 26 V dual operational amplifier, and distributor technical data lists a 3 V to 26 V working range with a 0.7 mA typical supply current drain that is largely independent of the supply voltage. That wide range lets one part number serve 5 V, 12 V and 24 V nominal automotive and industrial rails.
What is the gain bandwidth product and slew rate of LM2904QDRG4Q1?
The LM2904QDRG4Q1 provides a 700 kHz gain-bandwidth product and a 0.3 V/us slew rate per amplifier. Distributor specifications for this part list the 700 kHz gain-bandwidth figure together with the 0.3 V/us slew rate and the 8-SOIC package. These are typical general-purpose bipolar values, adequate for audio-band and low-frequency signal conditioning but not intended for wideband video or precision micropower designs.
Is the LM2904QDRG4Q1 AEC-Q100 qualified?
Yes. The LM2904QDRG4Q1 is AEC-Q100 qualified for automotive use. Texas Instruments states that the LM2904-Q1, LM2904B-Q1 and LM2904BA-Q1 are industry-standard operational amplifiers qualified for automotive applications in accordance with AEC-Q100 specifications. Use this part for body electronics, actuator drivers and 12 V battery-derived modules where automotive qualification, not just temperature rating, is required.
Where can I download the LM2904QDRG4Q1 datasheet PDF?
The LM2904QDRG4Q1 datasheet is available from the Texas Instruments product page for LM2904-Q1, which links the full LM2904-Q1, LM2904B-Q1 and LM2904BA-Q1 data sheet covering electrical characteristics, typical performance curves and pin configuration. The same document is mirrored on parts documentation portals such as alldatasheet and datasheets.com. Use the pin-description and typical-characteristics sections of that document when laying out the board.
Where can I find the LM2904QDRG4Q1 pinout?
The LM2904QDRG4Q1 uses the standard 8-pin SOIC (DBV) dual op amp pinout: pin 1 is amplifier 1 output, pin 2 is inverting input 1, pin 3 is non-inverting input 1, pin 4 is ground or V-, pin 5 is non-inverting input 2, pin 6 is inverting input 2, pin 7 is amplifier 2 output, and pin 8 is the positive supply. This is the classic LM358/LM2904 footprint, so it is directly interchangeable with most general-purpose dual amplifiers.
What can replace the LM2904QDRG4Q1?
The LM2904QDRG4Q1 can be replaced by pin-to-pin dual general-purpose amplifiers in the same 8-SOIC footprint, including the automotive-qualified LM2904B-Q1 and LM2904BA-Q1 from Texas Instruments, and STMicroelectronics LM2904DT and LM2904ST for non-automotive builds. Note that the LM2904B-Q1 and LM2904BA-Q1 raise the maximum supply voltage to 36 V, so verify rail headroom in your design. Always confirm AEC-Q100 status before substituting into automotive production.
What is the best STMicroelectronics equivalent for the LM2904QDRG4Q1?
The closest STMicroelectronics equivalents are the LM2904DT and LM2904ST, both dual general-purpose operational amplifiers in the same 8-SOIC (DBV) package with the same pin assignment as the LM2904. The key difference is qualification: the LM2904QDRG4Q1 carries AEC-Q100 automotive qualification, while the ST parts are standard industrial-temperature grades, so the ST options suit prototype or industrial designs rather than automotive production.
LM2904QDRG4Q1 vs LM2904B-Q1 - which is better for automotive use?
Both are AEC-Q100 qualified dual op amps in 8-SOIC, but the LM2904B-Q1 is the next-generation member of the family and raises the maximum supply voltage to 36 V, according to the TI LM2904-Q1 product page. Choose the LM2904B-Q1 when your automotive rail can exceed 26 V, for example 24 V transient-heavy or 36 V systems; choose the LM2904QDRG4Q1 when 26 V is sufficient and you prefer the mature, broadly second-sourced footprint.
When should I choose the LM2904QDRG4Q1 over a standard LM2904?
Choose the LM2904QDRG4Q1 when your design is automotive or otherwise requires AEC-Q100 qualification, since the standard LM2904 is not automotive qualified. The electrical behaviour is essentially that of the industry-standard LM2904, with a 700 kHz gain-bandwidth product, 0.3 V/us slew rate, 3 V to 26 V supply range and 65 dB CMRR, so the schematic and layout carry over unchanged. For non-automotive, cost-first prototypes the standard or STMicroelectronics variants are appropriate.
Is the LM2904QDRG4Q1 suitable for automotive body electronics and sensor interfaces?
Yes, the LM2904QDRG4Q1 is well suited to automotive body electronics. Its 3 V to 26 V single-supply range covers 12 V battery-derived rails with transient margin, and the 65 dB CMRR plus low supply-current drain independent of supply voltage suit battery-powered modules and sensor conditioning channels. Use it for resistive sensor interfaces, actuator and relay drivers, and battery monitoring, keeping input bias and offset error budgets inside the amplifier's general-purpose accuracy class.
What are the key specifications of the LM2904QDRG4Q1 that engineers should know?
The LM2904QDRG4Q1 is a dual general-purpose operational amplifier with two independent internally compensated channels, a 3 V to 26 V single supply, 700 kHz gain-bandwidth product, 0.3 V/us slew rate, 0.7 mA typical supply current per amplifier, and 65 dB CMRR, all in an 8-SOIC (DBV) package with tape-and-reel packaging and AEC-Q100 automotive qualification. Offset voltage, input bias current and output swing limits are specified in the manufacturer data sheet.
Where can I buy the LM2904QDRG4Q1 online?
Use the Request a Quote form on this page to request LM2904QDRG4Q1 pricing, stock allocation and lead time from XAIPART. The part is an active Texas Instruments orderable item supplied in tape-and-reel packaging, so standard surface-mount assembly lines can consume it without modification. For confirmation of the exact orderable status of the automotive suffix, the manufacturer LM2904-Q1 part-details page carries the current part-number listing and package information.
What is the price of the LM2904QDRG4Q1?
Pricing for the LM2904QDRG4Q1 is returned through the Request a Quote form on this page rather than as a static figure, because volume breaks, pack quantity and lead time change with order volume and market conditions. The part ships as tape and reel in the standard 8-SOIC (DBV) package. Submit a quote request with your target quantity and date code requirement for a current delivered price and schedule.
What is the lead time and stock status for the LM2904QDRG4Q1?
Current stock and lead time for the LM2904QDRG4Q1 are provided through the Request a Quote form on this page, which reflects live supplier position for the automotive-qualified orderable. Because the LM2904 family is a long-lived, widely stocked platform, allocation is normally straightforward for standard quantities, but automotive-qualified date codes and traceability documentation can affect scheduling. State your required date code and traceability level when requesting the quote.
What is the difference between the LM2904QDRG4Q1 and the LM2904ST?
The functional difference is automotive qualification and package marking: the LM2904QDRG4Q1 is the AEC-Q100-qualified Texas Instruments version of the LM2904-Q1 family, while the LM2904ST is a standard-grade STMicroelectronics dual op amp in the same 8-SOIC (DBV) package with the same pinout. The core AC and DC ratings are broadly comparable, but only the LM2904QDRG4Q1 carries the automotive qualification needed for production vehicle electronics.

داتای سەرچاوەی ئەندازیاری بۆ LM2904QDRG4Q1 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM2904QDRG4Q1 when the design is automotive or requires AEC-Q100 qualification and a 26 V maximum supply is sufficient; it gives you the industry-standard LM2904 8-SOIC footprint with two independent channels, 700 kHz bandwidth, 0.3 V/us slew rate and 0.7 mA typical supply current per amplifier. Choose the LM2904BQDRG4Q1 or LM2904BAQDRG4Q1 when your rail can exceed 26 V, since those next-generation members are specified to 36 V and remain automotive qualified. Choose the standard LM2904QD for non-automotive, cost-first designs where qualification paperwork is not required. Choose STMicroelectronics LM2904DT or LM2904ST for prototypes and industrial products that need a second source on the identical 8-SOIC footprint. For low-voltage systems where the input must swing to the positive rail, or for precision applications demanding microvolt offsets, step up to a rail-to-rail precision dual amplifier such as the OPA2196 or TLV9062 rather than forcing this general-purpose part outside its input common-mode range.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2904BQDRG4Q1 LM2904BAQDRG4Q1 LM2904QD LM2904DT LM2904ST
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments STMicroelectronics STMicroelectronics
Package 8-SOIC (DBV) 8-SOIC (DBV) - same 8-SOIC (DBV) - same 8-SOIC (DBV) - same 8-SOIC (DBV) - same 8-SOIC (DBV) - same
AEC-Q100 Automotive Qualification Qualified Qualified Qualified Not qualified Not qualified Not qualified
Number of Amplifiers 2 2 2 2 2 2

جیاکەرەوە سەرەکییەکان

  • Automotive qualification in the classic 8-SOIC general-purpose footprint (بەراورد بەLM2904DT)
  • Wide 3 V to 26 V single-supply operating range with 700 kHz bandwidth (بەراورد بەLM2904QD)
  • Lower maximum supply voltage keeps the part compatible with standard 26 V rails while remaining AEC-Q100 qualified (بەراورد بەLM2904BQDRG4Q1)
  • Supply-current drain largely independent of supply voltage (بەراورد بەLM2904ST)

تێبینییەکانی دیزاین

Estimated: with both channels biased at 5 mA each from a 12 V rail, the LM2904QDRG4Q1 dissipates roughly (12 V - 10 V) x 10 mA = 20 mW from the internal class-A output stage bias, plus the 0.7 mA typical supply current per amplifier across 12 V, giving about 17 mW of supply power and negligible junction heating. Actual dissipation is dominated by output stage quiescent current and output swing, so keep continuous output current per channel well below 10 mA unless the load is DC-coupled with minimal swing. Place a 0.1 uF ceramic bypass capacitor directly across pins 8 and 4 and add 1 uF to 10 uF of bulk capacitance near the package for supply transients.

The LM2904QDRG4Q1 is an internally compensated bipolar amplifier with no external compensation network, but it is still sensitive to parasitic capacitance at the inverting input. Keep feedback resistors physically close to the pins, route the non-inverting input away from the output and supply traces, and use a ground guard or a solid ground pour under the amplifier to reduce noise coupling. In automotive harnesses, keep the SOIC away from relay contacts and injector drivers, and route the supply trace away from motor and solenoid current paths to avoid supply ripple coupled through the 3 V to 26 V rail.

The most common design error with this amplifier family is expecting rail-to-rail input or output behaviour. The input common-mode range includes ground but does not extend to the positive supply, and the output swing cannot reach the positive rail, so a non-inverting input biased at the supply rail will saturate the amplifier. The second common error is exceeding the 26 V maximum supply voltage on the LM2904-Q1 member of the family; if your rail can exceed 26 V, use the LM2904B-Q1 or LM2904BA-Q1, which are specified to 36 V. Finally, confirm AEC-Q100 status and temperature grade before releasing an automotive design.

The 0.3 V/us slew rate and 700 kHz gain-bandwidth product set a practical closed-loop bandwidth ceiling of roughly 100 kHz at modest gain, so this part should be treated as a low-frequency signal amplifier only. For feedback-factor stability, keep the noise gain flat and avoid capacitive loading on the output; if driving a long harness or cable, insert an isolation resistor of roughly 100 ohm close to the output pin and add an RC filter to control cable capacitance. Use the two channels for a matched filter stage when channel-to-channel gain matching matters.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Qualified
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The LM2904-Q1 family is qualified for automotive use in accordance with AEC-Q100 per the Texas Instruments product page. RoHS compliance applies to the lead-free SOIC (DBV) package; REACH, halogen-free status and conflict-minerals declarations are not published on the part pages cited here and are therefore recorded as unknown.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2904QDRG4Q1 LM2904QDRG4Q1 datasheet LM2904QDRG4Q1 datasheet pdf LM2904QDRG4Q1 pinout LM2904QDRG4Q1 schematic LM2904QDRG4Q1 equivalent LM2904QDRG4Q1 replacement LM2904QDRG4Q1 drop-in replacement Texas Instruments LM2904QDRG4Q1 LM2904-Q1 AEC-Q100 dual op amp LM2904 8-SOIC dual op amp 26V LM2904QDRG4Q1 vs LM2904B-Q1 LM2904QDRG4Q1 automotive body electronics LM2904QDRG4Q1 price LM2904QDRG4Q1 stock and lead time

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM2904QDRG4Q1 LM2904-Q1 LM2904B-Q1 LM2904BA-Q1 LM2904DT LM2904ST STMicroelectronics dual operational amplifier op amp analog amplifier IC integrated circuit semiconductor AEC-Q100 RoHS 8-SOIC DBV package SOIC surface mount SMD gain bandwidth product slew rate common-mode rejection ratio CMRR internal compensation single-supply operation automotive body electronics battery management
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ